Setting Mitchell On-Demand v 5.8 DVD

Setting Mitchell On-Demand v 5.8 DVD
General information.
Kit Mitchell On-Demand DVD consists of 13 DVD, installation CD (Installation CD), and DVD
drive Estimator Parts and Labor (normochasy and spare parts).
Attention! On the installation disk also contains a Internet Explorer 6.0 distribution. If you have an
older version, you need to upgrade. (The renewal will also be started automatically if necessary, but
Setting.
I. Installation program.
1.
eC
ar
the version of IE will change with the English.)
Insert the CD-ROM drive Install CD. If the installation does not start automatically, run
ftw
ar
autorun.exe (Click on the icon to disk, right-click and select from the drop-down menu "Open",
So
click 2 times on the autorun.exe).
Attention! Any break up the installation, except the button Cancel, can cause problems in the
future, ie You can not successfully install the program. Make sure have enough time (about 30
min.) To bring the installation to finish.
Create an installation floppy.
To do this, press box «Дискета» (creation of the keydisk), pre-setting a blank floppy in the drive
3,5
If your computer does not drive 3.5-inch then you can use a virtual floppy disk. This program is on
eC
ar
the installation disk in the folder «Virtual_Floppy_Driver-2» file vfdwin.exe
So
ftw
ar
Not removing the floppy disk, click the button «Установка» (shell setup, Install)
eC
ar
2. In the license agreement, tick, and then "Next".
3. Fill in two fields in the form of "Company Information": Account Number - any text in Latin
ftw
ar
characters or numbers, Shop Name - Company Name (not required). If necessary, click the "Browse
..." and change the installation directory program. (Not recommended) to install the program
requires about 600 Mb. Attention! If you have drive Mitchell Estimator, it is desirable that the
So
location of the program was free an additional 600 Mb. Click "Next".
ftw
ar
II. Installing applications.
eC
ar
4. Upon completion of the installation process, click "Finish".
So
1. After the installation procedure starts automatically add a new product (see below), tick
«Repair» and «Estimator» (if you have a kit). Click "Next".
Specify the path to your DVD-drive. Insert any of the DVD-ROM drive in the appropriate drive.
Make sure the license diskette in the drive is a 3.5''drive. Click "Next".
eC
ar
So
ftw
ar
5. Specify the path to each DVD. (You can also copy the DVD to various directories on your hard
drive, then it is necessary to specify the path to them). Not removing the floppy from the drive,
click "Next".
ftw
ar
eC
ar
6. To complete the installation of Mitchell Repair Press “Finish”.
7. If you pointed out in paragraph 1 tick and installation Mitchell Estimator, the installation will
start automatically
So
If not, click «Add Data» and tick the "Data Selection". Click "Next." Otherwise, skip to step 13.
8. Make sure the license diskette drive is installed, and disk Mitchell Estimator - in CD-Rom drive,
ftw
ar
eC
ar
and specify the path to the CD-Rom with the button "Browse". Click "Next".
9. Repeat what you did in PP. 3 and 4.
So
10. In the next window, not removing the floppy, click "Next".
11. You can copy data to the Estimator CD to your hard drive. Copying is carried out at the same
location where you installed the program! If you have not less than 1100 Mb of free space on the
disk where you installed the program and are encouraged to do so and leave the box "Copy all of
the Estimator data to your computer. Otherwise, the tick should be removed. Not removing the
ftw
ar
eC
ar
floppy, click "Next".
So
12. Click "Finish" to complete the installation of data "Estimator ”.
13. Start the program with the button Repair / Estimator. If you need to view or change your
ftw
ar
eC
ar
settings, add a new product, etc., please contact menu Setup.
III. Troubleshooting (problems).
So
1. If immediately after the launch of an error, first remove the program via the Control Panel ( «Add
/ Remove Programs»), then locate the file in the Windows directory and delete it OD5.INI. Repeat
the installation.
2. If you have problems with displaying information on the maintenance (Maintenance) and / or
fails (or does not show entries) when working with the Estimator, switch option «Regional
Standards» in "English (USA)". This is done in the control panel, regional settings ( «Language and
Standards»).