Main Applications
Transcription
Main Applications
ME2500 High Density Polyethylene · Injection Molding Grade Main Applications Caps for beverage bottles Description LUTENE-H ME2500 is mainly intended for injection molding of bottle caps. It has good gas permeability characteristics and high toughness. General Characteristics Physical properties Test methods Units Values Melt Flow Index 190 /2.16 ASTM D 1238 g/10min 2.0 Density at 23℃ ASTM D 792 g/㎤ 0.952 DSC ℃ 131 LG method - narrow Crystalline Melting Point Molecular Weight Distribution Mechanical properties Test methods Units Values Tensile Strength at Yield ASTM D 638 kg/㎠ 280 Elongation at Break ASTM D 638 % > 1000 IZOD Impact Strength at 23℃ (notched) ASTM D 256 kg·㎝/㎝ 10 Flexural Modulus ASTM D 790 kg/㎠ 8000 Hardness (Shore D) ASTM D 2240 - 64 Softening Point (Vicat) ASTM D 1525 ℃ 123 ※ The tables give typical values measured on compression molded specimen. These value should not be considered as specifications. ※ Individual measurements may deviate from these values depending on the conditions under which the test specimen was prepared. LG Petrochemical ME2500S High Density Polyethylene · Injection Molding Grade Main Applications Caps for beverage bottles Description LUTENE-H ME2500S is for injection molding of bottle caps. It has good characteristics of gas permeability and high toughness. It has a lubricant for torque-releasing. Certificate This is to certify that LUTENE-H ME2500S is a suitable HDPE material Intended to come into contact with Foodstuffs. LUTENE-H ME2500S has been tested in accordance with the German Federal Health Office (BGA) regulations, the Japanese Food Sanitation Law and FDA 21 CFR 177.1520 For HDPE. K. H. SEO Manager Quality Assurance HDPE Plant LG Petrochemical ME2500S High Density Polyethylene · Injection Molding Grade Main Applications Caps for beverage bottles Description LUTENE-H ME2500S is for injection molding of bottle caps. It has good characteristics of gas permeability and high toughness. It has a lubricant for torque-releasing. General Characteristics Physical properties Test methods Units Values Melt Flow Index 190 /2.16 ASTM D 1238 g/10min 2.0 Density at 23℃ ASTM D 792 g/㎤ 0.952 DSC ℃ 131 LG method - narrow Crystalline Melting Point Molecular Weight Distribution Mechanical properties Test methods Units Values Tensile Strength at Yield ASTM D 638 kg/㎠ 280 Elongation at Break ASTM D 638 % > 1000 IZOD Impact Strength at 23℃ (notched) ASTM D 256 kg·㎝/㎝ 10 Flexural Modulus ASTM D 790 kg/㎠ 8000 Hardness (Shore D) ASTM D 2240 - 64 Softening Point (Vicat) ASTM D 1525 ℃ 123 ※ The tables give typical values measured on compression molded specimen. These value should not be considered as specifications. ※ Individual measurements may deviate from these values depending on the conditions under which the test specimen was prepared. LG Petrochemical ME3200 High Density Polyethylene · Injection Molding Grade Main Applications Caps for beverage bottles Description LUTENE-H ME3200 is for injection molding of bottle caps. It has good processability and high toughness. Certificate This is to certify that LUTENE-H ME3200 is a suitable HDPE material Intended to come into contact with Foodstuffs. K. H. SEO Manager Quality Assurance HDPE Plant LG Petrochemical ME3200 High Density Polyethylene · Injection Molding Grade Main Applications Caps for beverage bottles Description LUTENE-H ME3200 is mainly intended for injection molding of bottle caps. It has a high toughness and flow-ability. General Characteristics Physical properties Test methods Units Values Melt Flow Index 190 /2.16 ASTM D 1238 g/10min 3.2 Density at 23℃ ASTM D 792 g/㎤ 0.952 DSC ℃ 131 LG method - narrow Crystalline Melting Point Molecular Weight Distribution Mechanical properties Test methods Units Values Tensile Strength at Yield ASTM D 638 kg/㎠ 275 Elongation at Break ASTM D 638 % > 1000 IZOD Impact Strength at 23℃ (notched) ASTM D 256 kg·㎝/㎝ 8 Flexural Modulus ASTM D 790 kg/㎠ 8000 Hardness (Shore D) ASTM D 2240 - 64 Softening Point (Vicat) ASTM D 1525 ℃ 123 ※ The tables give typical values measured on compression molded specimen. These value should not be considered as specifications. ※ Individual measurements may deviate from these values depending on the conditions under which the test specimen was prepared. ME5000 High Density Polyethylene · Injection Molding Grade Main Applications Caps for mineral water bottles, Dust bin, Pails Description LUTENE-H ME5000 is mainly intended for injection molding of bottle caps. It has a high toughness and flow-ability. Certificate This is to certify that LUTENE-H ME5000 is a suitable HDPE material Intended to come into contact with Foodstuffs. The LUTENE-H ME5000 has been tested in accordance with the German Federal Health Office(BGA) regulations and the Japanese Food Sanitation Law. K. H. SEO Manager Quality Assurance HDPE Plant LG Petrochemical ME5000 High Density Polyethylene · Injection Molding Grade Main Applications Caps for mineral water bottles, Dust bin, Pails Description LUTENE-H ME5000 is mainly intended for injection molding of bottle caps. It has a high toughness and flow-ability. General Characteristics Physical properties Test methods Units Values Melt Flow Index 190 /2.16 ASTM D 1238 g/10min 5.0 Density at 23℃ ASTM D 792 g/㎤ 0.952 DSC ℃ 130 LG method - narrow Crystalline Melting Point Molecular Weight Distribution Mechanical properties Test methods Units Values Tensile Strength at Yield ASTM D 638 kg/㎠ 270 Elongation at Break ASTM D 638 % > 500 IZOD Impact Strength at 23℃ (notched) ASTM D 256 kg·㎝/㎝ 7 Flexural Modulus ASTM D 790 kg/㎠ 7500 Hardness (Shore D) ASTM D 2240 - 64 Softening Point (Vicat) ASTM D 1525 ℃ 123 ※ The tables give typical values measured on compression molded specimen. These value should not be considered as specifications. ※ Individual measurements may deviate from these values depending on the conditions under which the test specimen was prepared. LG Petrochemical