before you order your seat cushions

Transcription

GROUP 18: FRONT SEAT FRAME SPOTTER'S GUIDE
BEFORE YOU ORDER YOUR SEAT CUSHIONS OR COVERS,
MAKE SURE THAT YOU KNOW WHAT SEAT FRAMES YOU HAVE!
MB or GPW DRIVER (LATE STYLE B1811 or EARLY STYLE B1811-E)
UPPER SHEET METAL PAN HAS (2) REINFORCEMENT BEADS ROLLED FROM SIDE TO SIDE THAT ARE VISIBLE FROM THE REAR OF THE JEEP;
SEAT CUSHIONS SIT ON THE FACE OF THE PAN & ATTACH WITH SCREWS & WASHERS; CUSHION DOES NOT COVER BACK SIDE OF THE UPPER SEAT PAN.
LOWER BOTTOM PAN IS WELDED TO THE SEAT FRAME & HAS ACCESS HOLES FOR THE GAS TANK FILLER CAP.
Late Style
B1811 IS THE LATE STYLE SEAT FRAME FOR GAS TANK B0301-LH WITH THE LARGE 4-5/8" DIAMETER FILLER NECK CAP;
with Large
B1811-E IS THE EARLY STYLE SEAT FRAME FOR GAS TANK B0301-EH WITH THE SMALL 2-7/8" DIAMETER FILLER NECK CAP.
Gas Tank Filler
UPPER PAN SIZE: 18" WIDE X 14" HIGH
LOWER PAN SIZE: 18" WIDE X 15-1/2" FRONT TO BACK
Hole (B1811)
CAN BE RETROFITTED OR FOUND IN ANY JEEP; SOLD AS A BARE FRAME. YOU MUST ORDER UPHOLSTERY SEPARATELY.
(2A1811) CJ2A; (3A1811) CJ3A & 1950'S EARLY CJ3B; (C1811-N) M38 DRIVER
LOWER COVER/CUSHION IS DRAWSTRINGED AROUND A REMOVEABLE SHEET METAL PAN, (SOMETIMES REPLACED WITH PLYWOOD).
THE LOWER PAN BOLTS TO THREE CROSS BARS ON LOWER SEAT FRAME
SEAT HAS TWO LEGS THAT BOLT TO FLOOR IN VARYING CONFIGURATIONS
REAR OF SEAT LEANS ON & BOLTS TO FENDER WELL
M38
(C1811-N)
also fits
CJ3A & CJ3B
CJ2A
(2A1811)
CAN BE RETROFITTED OR FOUND IN ANY JEEP
SOLD AS A BARE FRAME. YOU MUST ORDER UPHOLSTERY SEPARATELY.
CJ3A
or CJ3B
(3A1811)
also fits M38
(D1811-N) M38A1 DRIVER
UPPER SHEET METAL PAN HAS (3) REINFORCEMENT BEADS ROLLED FROM SIDE TO SIDE THAT ARE VISIBLE FROM THE REAR OF THE JEEP
UPPER SEAT CUSHION SITS ON THE FACE OF THE PAN & ATTACHES WITH SCREWS & WASHERS; CUSHION DOES NOT COVER BACK SIDE OF THE UPPER SEAT PAN.
LOWER PAN BOLTS TO THREE CROSS BARS ON LOWER SEAT FRAME
SEAT HAS ONE LEG THAT BOLTS TO FLOOR WHILE THE OTHER LEG SITS ON & BOLTS TO DOORWAY OPENING
REAR OF SEAT LEANS ON & BOLTS TO FENDER WELL
M38A1
(D1811-N)
also fits
CJ5 & CJ6
(B1812) MB or GPW PASSENGER
LOWER BOTTOM PAN IS WELDED TO THE SEAT FRAME.
LEGS HAVE HINGES AND BOLT DIRECT TO FLOOR PAN;
SEAT LEANS ON FENDER WELL & CAN SWIVEL FORWARD.
CAN BE RETROFITTED OR FOUND IN ANY JEEP WITHOUT THE UNDER SEAT TOOL BOX
UPPER PAN SIZE:
18" WIDE X 14" HIGH
(2A1812) CJ2A & (3A1812) CJ3A, M38 & EARLY 1950'S CJ3B PASSENGER
UPPER SHEET METAL PAN HAS (3) REINFORCEMENT BEADS ROLLED FROM SIDE TO SIDE THAT ARE VISIBLE FROM THE REAR OF THE JEEP
UPPER SEAT CUSHION SITS ON THE FACE OF THE PAN & ATTACHES WITH SCREWS & WASHERS; CUSHION DOES NOT COVER BACK SIDE OF THE UPPER SEAT PAN.
PAN BOLTS TO THREE CROSSBARS ON LOWER SEAT FRAME
SEAT HAS TWO LEGS THAT HINGE ON TWO BRACKETS AT THE FRONT EDGE OF THE PASSENGER SIDE TOOL BOX;
SEAT LEANS ON FENDER WELL & CAN SWIVEL FORWARD.
CAN BE RETROFITTED OR FOUND IN ANY JEEP WITH THE UNDER SEAT TOOL BOX
UPPER PAN SIZE:
18" WIDE X 18" HIGH
LOWER PAN SIZE:
18" WIDE X 15-1/2" FRONT TO BACK
ALL EARLY CJ5 & CJ6; LATE 1960'S CJ3B LOW BACK BUCKET SEATS
CONTOURED, MORE MODERN LOW BACK FRONT BUCKET SEATS WITH NO SEAT UPPER OR LOWER METAL PAN
SPRINGS SPAN ACROSS TUBE STEEL FRAME & ARE A NON-REMOVEABLE INTEGRAL PART OF FRAME
ORIGINAL COVERS COVERED ENTIRE FRONT SEAT UPPER PORTION; THERE IS NO UPPER SHEET METAL PAN
VISIBLE FROM THE REAR OF THE JEEP; COVERS ARE UPHOLSTERED ON WITH HOG OR "C" RINGS.
SEAT HAS APPEARANCE OF THE 1960'S LOW BACK CAR SEATS (LIKE IN A 60'S MUSTANG CONVERTIBLE).
PASSENGER SEAT LEANS ON FENDER WELL & CAN SWIVEL FORWARD.
C
Copyright 2011 Beachwood Canvas Works Island Heights, N.J. 08732-0137 All Rights Reserved
ORDER NUMBERS LISTED ABOVE
TM10-3000 Page 46
GROUP 18: REAR SEAT FRAME SPOTTER'S GUIDE
B1813* MB GPW FOLDING MILITARY STYLE
SEAT BOTTOM CUSHION FITS WITHIN THE SEAT FRAME OUTER TUBING
FRONT LOWER FRAME'S TUBING HAS (5) HOLES DRILLED INSIDE FOR LOWER CUSHION FLAP ATTACHMENT
ORIGINAL CUSHION THICKNESSES WERE 1" UPPER & 2-1/2" LOWER
SEAT FOLDS IN HALF FOR STOWAGE & MOUNTS ON BRACKETS ON THE SIDES OF THE REAR WHEELHOUSES
WILL ONLY FIT IN AN MB OR GPW WITH HARDWARE SHOWN BELOW
UPPER SEAT OUTSIDE DIMENSIONS: 32"WIDE X 6" HIGH
LOWER SEAT OUTSIDE DIMENSIONS: 32"WIDE X 14"DEEP
C1813* M38 M38A1 FOLDING MILITARY STYLE
FRONT LOWER FRAME'S TUBING & REAR OF PAN EACH HAVE (5) HOLES DRILLED FOR CUSHION FLAP ATTACHMENT
ORIGINAL CUSHION THICKNESSES WERE 2-1/2" UPPER & 2-1`/2" LOWER
SEAT FOLDS IN HALF FOR STOWAGE & MOUNTS ON BRACKETS ON THE SIDE OF THE REAR WHEELHOUSES
CAN ALSO BE FOUND OR USED IN CJ2A CJ3A CJ3B CJ5 CJ6 WITH HARDWARE BELOW
UPPER SEAT OUTSIDE DIMENSIONS: 35"WIDE X 6" HIGH
B1836-F (2 RPV)
FORWARD REST
Original for: MB M38 M38A1
Retrofit: CJ2A 3A 3B 5 6
G1836-F (2 RPV)
FORWARD REST
Original for: GPW
Retrofit: MB CJ2A 3A 3B 5 6
B1833 (2 RPV)
SPRING LOCK
OR
Original for: MB GPW M38 M38A1
C1826 (2 RPV)
UPPER HOOK
Original for: M38
LOWER SEAT OUTSIDE DIMENSIONS: 35"WIDE X14" DEEP
B1826 (2 RPV)
UPPER HOOK
Original for: MB GPW
Retrofit: CJ2A 3A 3B 5 6 M38 M38A1
OR
OR
D1826 (2 RPV)
UPPER HOOK
Original for: M38A1
Retrofit: MB GPW CJ2A 3A 3B 5 6 M38
B1836-R (2 RPV)
REAR PIVOT
Original for: MB GPW
Retrofit: CJ2A 3A 3B 5 6 M38 M38A1
OR
C1836-R (2 RPV)
REAR PIVOT
Original for: M38 M38A1
Retrofit: MB GPW CJ2A 3A 3B 5 6
2A1813* CJ2A NON-FOLDING FREE-STANDING CIVILIAN "BUS" STYLE
ORIGINAL CUSHION THICKNESSES WERE 1" UPPER & 2-1/2" LOWER
SEAT IS FREE STANDING WITH LEGS, DOES NOT FOLD, & SNAPS INTO FLOOR RECEPTACLES
WILL ALSO FIT DIRECTLY INTO CJ3A CJ3B CJ5 CJ6 WITH 2A1804-S (2 RPV)
CAN BE RETROFITTED IN MB GPW M38 M38A1 WITH 2A1804-S RECEPTACLES (2 RPV)
UPPER SEAT OUTSIDE DIMENSIONS: 32" WIDE X 6" HIGH
LOWER SEAT OUTSIDE DIMENSIONS: 32" WIDE X 14" DEEP
CJ3A NON-FOLDING FREE-STANDING CIVILIAN "BUS" STYLE **
ORIGINAL CUSHION THICKNESSES UPPER & LOWER WERE 2-1/2"
WILL ALSO FIT DIRECTLY INTO CJ2A CJ3B CJ5 CJ6 WITH 2A1804-S (2 RPV)
CAN BE RETROFITTED IN MB GPW M38 M38A1 WITH 2A1804-S RECEPTACLES (2 RPV)
UPPER SEAT OUTSIDE DIMENSIONS: 32" WIDE X 15" HIGH
LOWER SEAT OUTSIDE DIMENSIONS: 32"WIDE X 14" DEEP
CJ3B CJ5 NON-FOLDING FREE-STANDING CIVILIAN "BUS" STYLE**
SEAT BOTTOM CUSHION IS SCREWED TO THE OUTSIDE OF & COVERS THE SEAT'S LOWER PERIMETER TUBING & PAN
ORIGINAL UPPER CUSHION THICKNESS 2-1/2"; BOTTOM CUSHION THICKNESS 4"
WILL FIT DIRECTLY INTO CJ3A CJ3B CJ5 CJ6 WITH 2A1804-S (2 RPV)
CAN BE RETROFITTED INTO MB GPW M38 M38A1 WITH 2A1804-S RECEPTACLES (2 RPV)
UPPER SEAT OUTSIDE DIMENSIONS: 32"WIDE X 15"HIGH
LOWER SEAT OUTSIDE DIMENSIONS: 32"WIDE X 14" DEEP
FRONT LOWER FRAME'S TUBING & REAR OF THE LOWER PAN HAVE HOLES DRILLED ALL AROUND THE
TUBE & PAN PERIMETER FOR LOWER CUSHION ATTACHMENT
*SOLD AS A BARE FRAME. YOU MUST ORDER UPHOLSTERY SEPARATELY.
** 3A1813 & 3B1813 SEAT FRAMES SUPPLY NOT ALWAYS RELIABLE, SO YOU CAN ORDER A FREE STANDING 2A1813,
OR FOLDING C1813 & RELATED HARDWARE AS A GOOD SUBSTITUTE, OR SEE 100-710-01 BELOW
R-100-710 AFTER MARKET FOLDING REAR SEAT
SUPPLIED FROM MANUFACTURER IN BLACK VINYL; WE CAN REUPHOLSTER IT TO MATCH YOUR FRONT SEATS
SEAT FOLDS IN HALF FOR STORAGE & MOUNTS ON BRACKETS ON SIDE OF REAR WHEELHOUSES
CAN BE MOUNTED IN CJ2A CJ3A CJ3B CJ5 CJ6 M38 M38A1 M170 & INCLUDES MOUNTING HARDWARE
C
TM10-3000 Page 47
GROUP 23: CJ SERIES CIVILIAN JEEP SEAT COVERS & CUSHIONS
SITUATION 1:
SEAT FRAMES WITH SPRINGS
& LOWER PANS
SITUATION 2:
SITUATION 3:
SITUATION 4:
SEAT FRAMES; NO SPRINGS
BUT WITH LOWER PANS
SEAT FRAMES; NO SPRINGS;
NO FRONT LOWER PANS
SEAT FRAMES & SUSPENDED SPRINGS;
WAS NEVER MADE WITH PANS
TYPICALLY
CJ2A CJ3A
Early 1950's CJ3B
TYPICALLY
CJ2A CJ3A
Early 1950's CJ3B
TYPICALLY
CJ5 CJ6 up to 1971
Late 1960's CJ3B
TYPICALLY
CJ2A CJ3A
Early 1950's CJ3B
Build your custom SEAT COVER or CUSHION SET (in an Array of Canvas or Vinyl Colors)
ON-LINE by inserting the Base Part Number below into the "SEARCH FOR" box at www.beachwoodcanvas.com
Otherwise please e-mail, fax or call us for current pricing!
DRIVER.................... UPPER .....................(2-1/2" Thick) ............................ Base Part Number....2A2302-1
DRIVER.................... LOWER.....................(3" Thick).................................... Base Part Number....2A2302-2
CJ2A
CJ3A
EARLY
CJ3B
CJ5
CJ6
FRONT SEAT
2A
REAR SEAT
2A
CJ5
CJ6
FITS SEAT FRAMES 2A1811 2A1812 3A1811 3A1812 C1811-N D1811-N
DRIVER......................... UPPER ..........................(2-1/2" Thick) ........................................................ Base Part Number.........2A2302-1
DRIVER......................... LOWER..........................(3" Thick; Unoriginal roomier thickness)........... Base Part Number.........2A2302-2
DRIVER......................... LOWER..........................(5" Thick; Original thickness).............................. Base Part Number.........3A2302-2
PASSENGER................. UPPER ..........................(2-1/2" Thick) ........................................................ Base Part Number.........2A2302-1
PASSENGER................. LOWER..........................(3" Thick; Unoriginal roomier thickness)........... Base Part Number.........2A2302-2
PASSENGER................. LOWER..........................(5" Thick; Original thickness).............................. Base Part Number.........3A2302-2
FITS SEAT FRAMES 2A1811 2A1812 3A1811 3A1812 C1811-N D1811-N
DRIVER....................UPPER .....................(Cover Only) . ............................ Base Part Number....5L2302-1
DRIVER.................... LOWER.....................(Cover Only)............................... Base Part Number....5L2302-2
Installation
Kit
Fronts Only
2A2303-F
(1 Kit Required)
(Screws & Washers)
Pan Screw
B2306-S
(8 Required)
Installation
Kit
Fronts Only
PASSENGER............ UPPER .....................(Cover Only) . .......... . ................Base Part Number....5L2302-3
PASSENGER............ LOWER.....................(Cover Only)............................... Base Part Number....5L2302-4
FITS SEAT FRAMES 5L1811 5L1812
LATE
CJ3B
3A
PASSENGER............ UPPER .....................(2-1/2" Thick) ............................ Base Part Number....2A2302-1
PASSENGER............ LOWER.....................(3" Thick).................................... Base Part Number....2A2302-2
LATE
CJ3B
REAR........................ UPPER ...(6" High x 30" Wide) . ................................ Base Part Number....B2301-5X
REAR........................ LOWER...(2-1/2" Thick; Fits inside of tubing)........... Base Part Number....B2301-6X
ABOVE FITS SEAT FRAMES B1813 2A1813
REAR FENDER WELL CUSHIONS (Pair; 10" x 29")............................... Base Part Number....B2381
REAR FENDER WELL CUSHIONS (Pair; 10" x 32")............................... Base Part Number....C2381
INSTALLATION KIT (Screws & Washers) for Fender Cushions................ Base Part Number....B2381-IKIT
REAR........................ UPPER ...(15" High x 30" Wide) . .............................. Base Part Number....3A2302-5
REAR........................ LOWER...(2-1/2" Thick; Fits inside of tubing)........... Base Part Number....B2301-6X
ABOVE FITS SEAT FRAME 3A1813
REAR........................ UPPER ...(15" High x 30" Wide) . .............................. Base Part Number....3A2302-5
REAR........................ LOWER...(4" Thick; Covers perimeter of tubing)..... Base Part Number....3B2302-6
ABOVE FITS SEAT FRAME 3B1813
BEFORE ORDERING, BE CAREFUL!
IDENTIFY YOUR SEAT FRAMES & YOUR SITUATION AS
SHOWN ABOVE BY USING THE
"SEAT FRAME SPOTTER'S GUIDES"
ON PAGES 46 & 47
C
b3061-x2g-p-1
(Hog Ring)
(as Required)
Installation
Kit
Rear Only
B2303-R
(1 Kit Required)
(Screws & Washers)
Installation
Kit
Rear Only
3A2303-R
(1 Kit Required)
(Screws & Washers)
Installation
Kit
Rear Only
3B2303-R
(1 Kit Required)
(Screws & Washers)
JEEPS WERE OFTEN BOUGHT FROM THE FACTORY WITH ONLY A
DRIVER'S SEAT! THE PASSENGER & REAR SEAT MAY HAVE BEEN
ADDED, EVEN BY THE WILLYS DEALERSHIP LATER ON, WITH
WHATEVER FIT!
TM10-3000 Page 48
GROUP 23: CJ SERIES CIVILIAN JEEP SEAT COVERS, TOPS, & ENCLOSURES
ORIGINAL STYLE SEAT COVERS, INSERTS, & CUSHIONS
These covers duplicate the original CJ Series Jeep spring assembly covers and cushions, and are available in olive drab, grey, tan, or black
cotton canvas or olive drab, black, red, grey, white, tan, or brown vinyl. Each cover is double stitched as per original W-O specifications
and is ready for you to install on your springs! Springs unreplaceable or missing? Seat pans rusted out? NOT TO WORRY! Check out our
cushion AND COVER ORDER guide & SEAT FRAME spotter's guideS on pages 46, 47, & 48. Look for your particular
situation and use the grid to find the solution! Simple as that! The Spotter's guide will show you what to order to get you into a full seat
cushion arrangement. We can also re-pad and recover your original seat springs. (You must supply the springs, front seat bottom spring
pans stripped, cleaned and painted. For original CJ2A rear seat springs, upper and lower, or original CJ3A rear seat bottom springs, you
must also supply the border wire that is sewn into the cover.)
CJ Series "TRAILRUN" HALF & FULL SUMMER TOPS or DELUXE "WINTER" HALF OR FULL ENCLOSURES
Although these jeeps were not offered with summer tops, we simplified our original winter top patterns by eliminating non-essential
flaps, hardware, and reinforcements required for side curtains. The top cost is reduced yet the top still uses our high quality materials
and constuction standards, and maintains overall original appearance. Features includes double stitched rear bow seam, reinforced lower
rear panel, heavy weight D.O.T. approved safety window, black hardware, and issue stenciling. (NOTE: These tops don’t accept curtains
and can’t be converted to a winter top later.). Our Willys-Overland design CJ series jeep enclosures conform to original dimensions and
utilize original bow and rod work. These enclosures are constructed from heavy CJ grey, olive drab, tan, or black cotton canvas, and
duplicate the original full and half cab options. All windows are heavy weight D.O.T. approved (on CJ2A tops, windows are sized such
that original CJ2A window frames can be installed at a later date). Some key side curtain canvas hardware is supplied uninstalled allowing for variations in your jeep body and bows, providing for a perfect custom fit! Use the TOP & ENCLOSURE SPOTTER'S GUIDE
on page 50 to determine what you need!
MILITARY Style Field Expedient "TRAILRUN" TOPS & ENCLOSURES for CJ SERIES CIVILIAN JEEPS
Whether you have a mix & match jeep or are just trying to give your beauty that militarized appearance by signing it up for active
duty, we can make a top or enclosure that fits the bill! Check out ALL2308-HYBRID and add this item to the CART on-line to see all
of the combinations......(Additional hole drilling, metal and framework is required)............Here are just a few examples!
CJ2A Body with CJ2A Windshield & MB Top Bows........(Summer Top) . .....ALL2308-HYBRID..(Winter Enclosure) . .............2A2340-MB-2A
CJ2A Body with CJ2A Windshield & M38 Top Bows. .....(Summer Top) . .....ALL2308-HYBRID..(Winter Enclosure) . .............2A2340-M38-2A
CJ2A
CJ3A
CJ3B
CJ5
NOTE: Straps and all other accesories are in the JEEP STRAPS & WELTS section.
MADE IN U.S.A.!
HEAVY DUTY INDOOR/OUTDOOR STORAGE COVERS
MB, GPW, CJ2A, CJ3A, M38, CJ3B, CJ5, M38A1, M422A1 & M151 Series.
NEW!
YOU ASKED FOR IT! And we delivered! We now offer heavy duty olive drab 18 oz. vinyl coated polyester rip-stop storage covers made to protect your jeep from the elements. These super duty covers are puncture, tear, ultra-violet, mildew,
shrink and water resistant. Just what you need if you lack garage space. Don't confuse these with light-weight dust covers of
equivalent price on the market. These are made for an outdoor beating! Covers listed below will fit:
Windshield Up
Windshield & Top Up
Windshield & Top Down
Order No. B2384-VCPWU
Order No. B2384-VCPTU
Order No. B2384-VCP
1/4 Ton JEEP Trailers (MBT, BT3, M100, BT3-C, M416)...........BT2384-VCP
Bungee Tie-down kit for any cover.............B1984-B
Also ask about our special production EXTRA LONG (XL) Series Storage covers
for JEEPS that reach down & touch the ground in order to protect your entire tire from UV exposure!
C
TM10-3000 Page 49
GROUP 23: CJ SERIES CIVILIAN JEEP TOP & ENCLOSUREs
(2) PIECE
TRAILRUN
SUMMER
HALF
CAB TOP
(1) PIECE
TRAILRUN
SUMMER
HALF
CAB TOP
(3) PIECE
DELUXE
WINTER
HALF CAB
ENCLOSURE
(5) PIECE
DELUXE
WINTER
FULL CAB
ENCLOSURE
(1) PIECE
TRAILRUN
SUMMER
FULL
CAB TOP
(2) PIECE
TRAILRUN
SUMMER
FULL
CAB TOP
(4) PIECE
DELUXE
WINTER
HALF CAB
ENCLOSURE
JEEP is a registered trademark
of the Chrysler Corporation
(6) PIECE
DELUXE
WINTER
FULL CAB
ENCLOSURE
(7) PIECE
DELUXE
WINTER
HALF CAB TO
FULL CAB
CONVERSION
ENCLOSURE
Build your custom TOP or ENCLOSURE (in an Array of Canvas Colors)
TOP or ENCLOSURE STYLE
CJ2A
CJ3A
CJ3B
CJ5
HALF CAB TRAILRUN SUMMER TOPS (1-piece & 2-piece Versions):
TRAILRUN SUMMER HALF TOP (Base Part Number). ..............................................2A2331........................3A2331........................3A2331........................5E2331
(Will not accept side curtains or doors; half cab only; can not be added to in order to make a full cab)
HALF CAB DELUXE WINTER TOPS & ENCLOSURES (3-piece & 4-piece Versions):
DELUXE WINTER HALF TOP ENCLOSURE (Base Part Number)............................2A2321........................3A2321........................3B2321........................5E2321
(Will accept side curtains or doors; half cab only; can not be added to in order to make a full cab)
FULL CAB TRAILRUN SUMMER TOPS (1-piece & 2-piece Versions):
TRAILRUN SUMMER FULL TOP....................................................................................2A2308........................3A2308........................3B2308........................5E2308
(Will not accept side curtains or doors; full cab only; does not break down to half cab)
FULL CAB DELUXE WINTER TOPS & ENCLOSURES (5-piece & 6-piece Versions):
(Will accept side curtains or doors; full cab only; does not break down to half cab)
FULL CAB DELUXE WINTER FULL CAB TO HALF CAB CONVERSION ENCLOSURES (7-piece Versions):
(Will accept side curtains or doors; breaks down from a full cab to a half cab top)
TOP BOW SET.....................................................................................................................2A1858........................2A1858........................2A1858........................5E1858
TOP BOW BRACKETS.......................................................................................................2A1859........................2A1859........................2A1859...........2A1859-2PR
TOP BOW STOWAGE BRACKETS (for side body stowage).........................................2A1858-STOW..........2A1858-STOW..........2A1858-STOW..........--------TOP BOW SUPPORT ROD KIT........................................................................................2A2319-RODKIT . ......... 3A2319-RODKIT............ 3A2319-RODKIT 5E2319-RODKIT
FRAME DOOR KIT.............................................................................................................3A2319-DOORKIT ......... 3A2319-DOORKIT .......... 3A2319-DOORKIT 5E2319-DOORKIT
LOWER DOOR PIVOT (2 Required)................................................................................2A2319-8....................2A2319-8....................2A2319-8....................--------UPPER DOOR PIVOT.........................................................................................................B2319-3......................3A2319-12..................3A2319-12..................3A2319-12
INSTALLATION VIDEO TAPE (VHS)...............................................................................V-2A2316....................V-3A2316....................V-3A2316....................V-5E2316
NOTE: ALL TOPS & ENCLOSURES ON THIS PAGE WORK ONLY WITH ORIGINAL BOWS & RODWORK!
SUMMER TOPS CAN ALSO BE QUOTED FOR HYBRID COMBINATIONS OF JEEPS & BOWS.
C
TM10-3000 Page 50
GROUP 18: TOP BOW SPOTTER'S GUIDE
MB GPW (B1858)
ROUND ENDS
BOWS MOUNT WITH EXTERNAL BRACKETS ON OUTSIDE OF REAR QUARTER PANELS
BOWS PIVOT INTO THE UP OR DOWN POSITION
BOWS ACT AS HAND RAIL IN DOWN POSITION
B1858
B0WS CAN BE USED OR FOUND RETROFITTED ON:
CJ2A CJ3A CJ3B CJ5 CJ6 M38 M38A1 WITH B1859, G1859 or B1859-W
B1859, G1859, & B1859-W
M38 & M38A1 (C1858)
FLAT ENDS
BOWS MOUNT WITH EXTERNAL BRACKETS ON OUTSIDE OF REAR QUARTER PANELS
BOWS ARE PLACED INTO THE UP OR DOWN POSITION
BOWS ACT AS HAND RAIL IN DOWN POSITION
C1859
B0WS CAN BE FOUND OR USED ON CJ5 CJ6 WITH D1859
B0WS CAN BE USED OR FOUND RETROFITTED ON:
MB GPW CJ2A CJ3A CJ3B WITH C1859
C1858
CJ2A CJ3A CJ3B CJ5 & CJ6
D1859
FORWARD BOW MOUNTS BEHIND FRONT SEATS IN SQUARE RECEPTACLES ON TOP OF THE REAR WHEELHOUSES;
REAR BOWS MOUNT TO EXTERNAL ROUND TUBES WELDED TO OUTSIDE OF REAR CORNERS OF BODY;
THE (6) PIECE BOW SET IS ASSEMBLED OR TAKEN APART FOR THE UP OR DOWN POSITION;
THE BROKEN DOWN BOWS ARE STOWED WHEN NOT IN USE ON THE CJ2A LOWER WINDSHIELD FRAME
& CJ2A REAR DRIVER'S SIDE QUARTER PANEL WITH 2A1858-STOW BRACKETS
OR ON THE TOP OF THE REAR WHEELHOUSES FOR ALL OTHER THE CJ3A CJ3B CJ5 CJ6
2A1858
(SEPARATES
INTO 6
PIECES)
2A1858 B0WS WILL DIRECTLY FIT ON CJ2A CJ3A CJ3B
5E1858 B0WS WILL DIRECTLY FIT ON CJ5 CJ6
2A1858 B0WS CAN BE RETROFITTED ON MB GPW M38 M38A1 WITH 2A1859
2A1859
GROUP 20: WINDSHIELD FRAME SPOTTER'S GUIDE
MB GPW (B2001-IO)
HEIGHT: 22"
AT CENTER
WINDSHIELD IS (2) PIECE WITH INNER SWING OUT SPLIT PANES
INNER WINDSHIELD HAS CENTER GRAB HANDLE
PANEL BELOW INNER WINDSHIELD IS FLAT UNMARKED PLAIN STEEL
INNER WINDSHIELD SWINGS OUT WITH B2014 SLOTTED SLIDE ARMS
ORIGINAL WINDSHIELD USED EITHER B2025-A OR B2025-B WINDSHIELD STUDS
(YOU CAN SUBSTITUTE UNORIGINAL 2A2025 OR 2A2025-R WINDSHIELD STUDS)
B2025-A
WINDSHIELD CAN BE USED OR FOUND RETROFITTED ON CJ2A CJ3A CJ3B M38
B2025-B
B2014
CJ2A (2A2001-IO OR 2A2001-IOW)
HEIGHT: 24"
AT CENTER
WINDSHIELD IS (2) PIECE WITH INNER SWING OUT SPLIT PANES
INNER WINDSHIELD HAS CENTER CAM LEVER CLOSING LOCK
ORIGINAL WINDSHIELD USED 2A2025 WINDSHIELD STUDS
2A2025
(YOU CAN SUBSTITUTE UNORIGINAL B2025-A, B2025-B, OR 2A2025-R STUDS)
WINDSHIELD HAS "WILLYS" STAMPED IN SHEET METAL PANEL BELOW INNER PANES
INNER WINSHIELD SWINGS OUT WITH 2A2014-KIT ROTATING "LOLLIPOP" SWING ARMS
2A2025-R
WINDSHIELD CAN BE USED OR FOUND RETROFITTED ON MB GPW CJ3A CJ3B M38
CJ3A (3A2003) & M38 (C2003)
HEIGHT: 26-1/2"
AT CENTER
2A2014-KIT
WINDSHIELD IS (1) PIECE WITH CLOSED VENT IN CENTER IN SHEET METAL PANEL BELOW GLASS
WINDSHIELD DOES NOT HAVE AN INNER SWING OUT GLASS FRAME
WINDSHIELD USES A "C" CHANNEL ROPE TRACK ABOVE THE GLASS FOR TOP ATTACHMENT
WINDSHIELD CAN BE USED OR FOUND RETROFITTED ON MB GPW CJ2A CJ3B
CJ3B (3B2003)
HEIGHT: 22"
AT CENTER
WINDSHIELD IS (1) PIECE WITH PLAIN FLAT STEEL PANEL BELOW GLASS
WINDSHIELD CAN BE USED OR FOUND ON MB GPW CJ2A M38
CJ5 CJ6 M38A1 & M170 (5E2003)
HEIGHT: 21"
AT CENTER
C
WINDSHIELD IS (1) PIECE WITH PLAIN FLAT STEEL PANEL BELOW GLASS
THIS WILL ONLY FIT M38A1 & M170, ALSO CJ5 & CJ6 UP TO 1975
TM10-3000 Page 51
GROUP 18 & 23: JEEP TOP BOWS, RODS, BRACKETS, & ACCESSORIES
We can supply top bows and brackets for most military and civilian jeeps. These bows duplicate all original dimensions and specs and
are an absolute must in order for your original top to work and fit properly. MB & GPW (B1859, G1859, or B1859-W), M38 (C1859),
M38A1 (D1859) military style top bow bracket sets contain (8) pieces which include cast thumbscrews
FRAME DOOR, HANDLE, LATCH PLATE & SUPPORT ROD KITS
VEHICLE
TOP BOW
SET
BOW BRACKET
SET
THUMBSCREW
WIRES & CHAINS
MB............................... B1858...................... B1859 or B1859-W......................B1857
GPW............................ B1858........................ B1859 or G1859.........................G1857
M38 or M38A1........... C1858........... (M38) C1859; (M38A1) D1859............C1857
M151 SERIES.............E1858.................................. ------..................................C1857
CJ2A, CJ3A or CJ3B.... 2A1858.............................. 2A1859................................. -----CJ5 or CJ6..................5E1858.......................... 2A1859-2PR............................. -----The DOOR KIT includes (2) door frames, handles, latch plates, striker plates, & rivets necessary to add doors to your jeep. You must
however, also use the ROD KIT in order to frame the jeep doorway for use with a winter enclosure. These kits supply the metal parts as per
original Willys Overland specifications, and assume that your jeep is complete as it left the factory. (In order to install a winter enclosure,
additional components may have to be ordered if they are missing from your jeep; such as windshield or body door pivot hinges).
DOOR FRAME (PAIR) KIT
SUPPORT ROD KIT
MB/GPW Late Style Winter Enclosure (B2340-L) Door & Rod Kit.............B2319-RODKIT.......................B2319-DOORKIT
M38 Winter Enclosure (Base Part Number C2320).............................................C2319-RODKIT......................3A2319-DOORKIT
M38A1 Winter Enclosure (Base Part Number D2320)........................................D2319-RODKIT......................5E2319-DOORKIT
CJ2A Winter Enclosure (Base Part Numbers 2A2320 & 2A2321)......................2A2319-RODKIT....................3A2319-DOORKIT
CJ3A Winter Enclosure (Base Part Numbers 3A2320 & 3A2321)......................3A2319-RODKIT....................3A2319-DOORKIT
CJ3B Winter Enclosure (Base Part Numbers 3B2320 & 3B2321)......................3A2319-RODKIT....................3A2319-DOORKIT
CJ5 Winter Enclosures (Base Part Numbers 5E2320 & 5E2321)........................5E2319-RODKIT....................5E2319-DOORKIT
CJ6 Winter Enclosures (Base Part Numbers 5E2320 & 5E2321)........................6E2319-RODKIT....................5E2319-DOORKIT
CJ2A, CJ3A, CJ3B, CJ5, or CJ6 top bow sets 2A1858 & 5E1858 require either the SUPPORT ROD KIT
listed above, or at a minimum, (1) each 2A1917-F & 2A1917-R support strap kit in order to stabilize
your bows set. MB, GPW, M38 or M38A1 top bow sets (B1858 or C1858) do not require a SUPPORT
ROD KIT, however, it is recommended that you either use one or make certain that your jeep's pivoting
top bow rivets are TIGHT and do not allow the center bow to bow to fall or "flop" onto the steering wheel
when the bow is released. The bow should stay in the position where placed so that the bow supports
the top and the top DOES NOT support the bow. See page 51 for bow descriptions.
1/4 & 1 TON TRAILER TARPS, ROPES, DATA PLATES, WIRING, & COVERS
Build your custom TRAILER TARP or COVER (in an Array of Canvas Colors)
Heavy duty, quality crafted, original style construction olive drab canvas trailer tarp with features such as double reinforced corners, triple reinforced edges, plated black
brass grommets, and issue stenciling. Available in canvas or durable rip-stop vinyl. Rope kits include enough pieces of mil-spec style ‘manila’ rope, cut to proper length,
with end clips; to secure one tarp. 1/4 ton trailer tarps lised here are the flat military style that simply cover the bed opening. If you are interested in the full enclosure
covered wagon style with end curtains (as was used on the BT3-C), please call for a quote). MBT is the WWII Willys trailer, BT3 is the WWII Bantam trailer, M100 is
the Korean War trailer, M416 is the Vietnam trailer, BT3-C is the post-WWII Bantam civilian trailer with tail gate, BC is the WWII airborne Converto dump trailer.
MBT
BT3
M100
M416
BT3-C
WIRING HARNESS EARLY (without cable, plug, & tail light sockets) BT0601
BT0601
1000601-E
4160601
---------
WIRING HARNESS LATE (without cable, plug, & tail light sockets)
---------
---------
1000601-L
---------
---------
TRAILER CABLE & PLUG ASSEMBLY WWII (4-Blade) BT0671-CP
BT0671-CP
---------
---------
---------
TRAILER CABLE & PLUG ASSEMBLY WWII (6-Blade) BT0671-CP6 BT0671-CP6
---------
---------
---------
TRAILER CABLE & PLUGS ASSEMBLY EARLY DOUBLE (M-Series)
--------- ---------
10000671-CPE ---------
---------
TRAILER CABLE & PLUG ASS'Y (M-SERIES LATE SINGLE) ---------
---------
10000671-CPL 10000671-CPL ---------
BODY & FRAME GROMMET KIT BT1843
BT1843
BT1843
BT1843
BT1843
BED OPENING (FLAT) TARP (Base Part Number)
BT2310
BT2310
BT2310
4162310
BTC2310
ROPE KIT FOR FLAT TARP (Base Part Number)
BT1910
BT1910
BT1910
BT1910
BTC1910
DATA PLATE(S) MBT2430
BT2430
1002430
4162430
---------
ONE TON "BEN HUR" STYLE TRAILER COVER ASSEMBLY AND ROPE KIT:
BC
----------------BT0671-CP
BT0671-CP6
----------------BT1843
BC2310
BC1910
---------
Heavy duty, quality crafted, original construction trailer tarp with features such as reinforced corners, triple reinforced edges, plated black brass grommets, integral end
flaps, leather or web closure straps, and issue stenciling. This cover is an exact duplicate of the American Bantam/Michigan Awning cover
and is the same cover we’ve supplied to the government.
ENCLOSURE (COVER) with integral end curtains & closure straps (Base Part Number)...................................... BH2316-X
Rope Kit for BH2316-X (Base Part Number). ................................................................................................... BH1916-R
C
TM10-3000 Page 52
GROUP 23: REPLACEMENT VINYL JEEP SEATS & ENCLOSURES
We are also able to supply cost effective replacement black vinyl after market jeep enclosures and seat assemblies. These enclosures are
supplied with ALL necessary hardware including door frames, brackets, top bows, mounting hardware, covers, and instructions. Nothing
else to buy! (You will have to drill holes). If you want to enclose your vehicle without the expense of original style bows and canvas, this
it the way to go! We also carry replacement after market rear seat assemblies. These seat assemblies can be retro-fitted on any earlier
jeep listed below. These are all great non-original economical solutions to your seating and top needs.
Vehicle & Year
MB & GPW (1941-45)
CJ2A (1946-48)
M38 or CJ3A (1950-52)
M606 or CJ3B (1953-64)
M38A1 (1951-64)
CJ5 (1955-75)
CJ5 (1976 & UP)
CJ6 (1955-75)
CJ7 & YJ (1970's & UP)
CJ8 (1981 & UP)
Enclosure Part No.
R-101-011
R-102-011
R-103-011
R-104-011
R-109-011
R-109-011
R-110-011
R-106-011
R-116-011
R-108-011
Rear Seat
-----------
R-100-710
R-100-710
R-100-710
R-100-710
R-100-710
R-100-710
R-100-710
R-100-710
R-100-710
HYBRID JEEP SEAT COVERS & TOPS
So your 1942 Willys MB mixed with a few other vehicles in its lifetime
and you ended up with a CJ2A windshield and M38 top bows, or a
CJ3A windshield, CJ3B seat frames, and M38A1 topbows, or.......Well,
believe us, we’ve seen and made patterns for almost every hardware
combination you could think of! Tell us your particular arrangement
and we will be glad to quote you a price for whatever you need in
seat covers and enclosures.
MIL-SPEC OLIVE DRAB VINYL SEAT COVERS & TOPS
Almost any canvas item in our catalog can be reproduced in heavy
weight mil-spec reinforced rip-stop vinyl, as used on later military
vehicles. Not only is this material water, mildew, rot, and shrink
resistant but it also has an integral tear resistant rip-stop mesh.
Coloring matches WWII spec olive drab. Best buy for your dollar
if you use your vehicle more than you show it! Many other colors
also available. Ask for sample today!
DESERT TAN SEAT COVERS & TOPS
THE OLIVE DRAB BLUES
No more searching for the right mil-spec khaki-tan for your special All canvas or vinyl seat covers and tops listed in this catalog foldesert project. Samples are awaiting your request! This coloring is low original color and material specs as close as possible. We are,
similar to the early war khakis.
however, able to provide these same covers on special order in
unoriginal color or material schemes, at nominal additional costs,
AHOY! NOW HEAR THIS! NAVY ENTHUSIASTS!
if you have a special project in mind. Tell us your ideas and we can
Almost any canvas item in our catalog can now be reproduced in Navy provide quotes and samples. Our inventory of colored cotton canvas
grey colored cotton canvas! GO NAVY! Request a sample!
includes OD, grey, black, & tan.
THE BEACHWOOD CANVAS CARGO TARP DIFFERENCE
FIG. 1
Here is the BEACHWOOD DIFFERENCE in our cargo bed tarp construction that outshines our competitors and
even exceeds the military’s specifications! Figure No. 1 depicts the standard military flat seam construction for bed
tarps where only two layers of nonreinforced canvas comprise each seam. Tarp grommets are sharp edged, prone
to rip out, and sometimes poorly finished or not finished at all. Now look at Figure No. 2, the BEACHWOOD
CONSTRUCTION! Each of our tarp’s seams is double felled and interlocked: four layers of material creating
its’ own seam reinforcement. Our grommets are high quality black plated brass with rolled edges and teeth to FIG. 2
prevent rusting, rip out, or glint! No unfinished or rough canvas edges, either. All edges are folded or finished.
If an original WWII specification called for leather reinforcements, that’s what you get, too! Whether you’re
purchasing a DELUXE or TRAIL RUN tarp, this is the type of attention to details you receive from
BEACHWOOD! Believe us, we try to carry these hidden extras through every product that we make.
AUXILIARY BENCH PADS (REAR WHEEL HOUSE CUSHIONS)
Build your custom SEAT COVER or CUSHION SET (in an Array of Canvas or Vinyl Colors)
These bench pads are modeled after the original Willys-Overland approved bench pads and attach to either the passenger or driver
side rear wheel housings on CJ2A, CJ3A, CJ3B, and early CJ5 jeeps. We can produce wheelwell (rear wheelhouse or fender)
cushions to increase comfort and passenger seating in your military jeep. For added truck troop seat comfort, we also have bench
pads as originally supplied with artic winterization kits. Use order number B2381-IKIT for any cushion pair listed below. Check
your body for presence of top bow brackets on top of the rear fender well in order to determine optimum cushion size.
Base Part Number for Cushion (pair)... ..............SIZE............................................VEHICLES with...................................................... VEHICLES without
Wheelhouse top bow brackets (sockets)
Wheelhouse top bow brackets (sockets)
B2381 . .................................. 10" x 29"............................................... CJ2A............................................................MB GPW CJ3A CJ3B
3A2381................................... 10" x 26"............................................... CJ3A CJ3B............................................................---------------C2381..................................... 10" x 32"............................................... CJ5...............................................................CJ2A CJ5 M38 M38A1
C
TM10-3000 Page 53
ALL GROUPS & JEEPS STRAPS, WELTS, COVERS, BOOTS, & FASTENERS
B2290
MB GPW
SHOWN
B2270-50
B2285
B2364
B2216-C
Build your custom CANVAS or WEB Product or Accessory (in an Array of Colors)
ITEM DESCRIPTION
MB
GPW
M151
CJ2A
CJ3A
CJ3B
CJ5
----
2A2303
3A2303
3B2303
----
----
----
----
----
----
4-I
----
----
----
----
----
CRASH PADS RECOVERED:
B2304-X B2304-X ----
Please supply your original metal
backs cleaned and painted. We recover
your metal backs with animal
hair inserts and canvas covers (1 RPV; pair).
----
----
----
----
----
----
CRASH PADS COMPLETE (with metal): B2304-X B2304-X ----
Crash pad assemblies made
from powder coated steel plates, horsehair
padding,and canvas; complete,
already upholstered; not a kit;
ready for installation (1 RPV; pair).
----
----
----
----
----
----
----
----
----
----
----
----
----
----
SEAT CUSHION INSTALLATION KIT:
B2303
B2303
Nearly (100) separate pieces of dull
black plated military finish stainless steel and brass slot head screw
nuts, and washers; fastens (1) set of
six cushions or covers to seat frames.
M38
C2303
C2303
3
CRASH PAD COVERS:
B2304-X B2304-X ----
Original style canvas covers
supplied so you can recover your
own crash pads (1 RPV; pair).
CRASH PAD INSERTS:
B2304-I
Genuine animal hair inserts supplied
so you can recover your own crash pads (1 RPV; pair).
INSTALLATION SCREWS FOR B2305 or B2306:
Round head slotted machine screws (8 RPV)
B2306-S
B2304-I
B2306-S
M38A1
----
4
----
----
5
6
----
DOORWAY “HALF CURTAINS”:
B2307-X B2307-X
Duplicates original doorway
curtains using original NOS brass
black antique hardware;jeep must have
properly set body sockets (1 RPV; pair).
(Also see Part No. B1824)
----
WINDSHIELD COVER (PLAIN FACE):
B2314-X B2314-X
Protects folded down windshield; prevents
aircraft observation due to glass reflection.
Originally MB or GPW issue. Accomodates windshields
with or without metal rifle racks or vacuum wiper motors.
(Specify plain face without a star at all; factory issue).
3A2314-X 5E2314-X E2314-X
C
7
----
2A2314-X 3A2314-X 3B2314-X 5E2314-X
14
TM10-3000 Page 54
B2025-A
CAST SNAP HOOK
USED ON
SAFETY STRAPS
B2025-B
37
MB GPW
SHOWN
B1851-L (CAST)
C1851 (WIRE)
WWII
1" BUCKLE & TIP
WWII
1-1/2" JERRY CAN STRAP
BUCKLE & TIP
ITEM DESCRIPTION
MB
GPW
M38
M38A1 M151
CJ2A
CJ3A
CJ3B
CJ5
WINDSHIELD COVER WITH STAR or B2314-X B2314-X 3A2314-X 5E2314-X E2314-X
INVASION STAR & CIRCLE:
Protects folded down windshield; prevents
aircraft observation due to glass reflection.
(Specify plain star or star with broken invasion circle).
2A2314-X 3A2314-X 3B2314-X 5E2314-X
STEERING COLUMN WASHER (LEATHER): B1416-L
B1416-L
B1416-L
B1416-L
Seals steering column at floor board RUBBER): B1416-R B1416-R B1416-R B1416-R
GAS PEDAL LINKAGE BOOT
(LEATHER): B0317-L
B0317-L
B0317-L
B0317-L
Seals pedal linkage at floor board
(RUBBER): B0317-R B0317-R B0317-R B0317-R ----
B1416-L
B1416-R
B1416-L
B1416-R
B1416-L
B1416-R
---5E1416
B0317-L
B0317-R
B0317-L
B0317-R
B0317-L
B0317-R
B0317-L
B0317-R
(LEATHER): B0718-L
TRANSMISSION BOOT
Genuine dark brown leather boot
(RUBBER): B0718-R
B0718-L
B0718-R
B0718-L
C0718
B0718-L
C0718
----
----
B0718-L
2A0718
B0718-L
2A0718
B0718-L
2A0718
B07182A0718
TRANSFERCASE BOOT
(LEATHER): B0818-L
Genuine dark brown leather boot
(RUBBER): B0818-R
B0818-L
B0818-R
B0818-L
2A0818
B0818-L
----
2A1818
18
B0818-L
2A0818
B0818-L
2A0818
B0818-L
2A0818
B0818-L
2A0818
B1719
2A1719
5E1719
----
2A1719
2A1719
3B1719
5E1719
STRAP SET for AX & SHOVEL:
B1920
B1920
B1920
100% Cotton straps with original
style appropriate WWII or postwar
plated dull black buckles and tips;
authentically secures tools on jeep.
D1920
E1920
----
----
----
----
STRAP SET for TOP BOW STOWAGE:
B1921
B1921
C1921
100% Cotton straps with original
style appropriate WWII or post-war
plated dull black buckles and tips;
secures stowed or folded top bows to jeep.
D1921
2A1921
2A1922
2A1922
2A1922
COLLAPSIBLE WATER BUCKET:
B2395
2-gallon reinforced pail as seen on almost
every WWII and many post war military vehicles.
B2395
B2395
B2395
B2395
B2395
B2395
COLLAPSIBLE WATER PITCHER:
B2398
RARE! Canvas pitcher stowed in the glove or
tool box; used to fill radiators. Very rare & handy!
B2398
B2398
B2398
B2398
B2398
14
16
HOOD WELT KIT:
Pre-cut 3/4" dual beaded welt buffers
radiator grill top from hood; includes rivets
C
B1719
Use B1719-E
for Slat Grill
MB Jeeps
B2395
17
19
20
E1921
21
B2395
95
B2398
B2398
B2398
98
TM10-3000 Page 55
ITEM DESCRIPTION
MB
GPW
M38
M38A1 M151
CJ2A
CJ3A
CJ3B
CJ5
STRAP SET for TOP STOWAGE:
100% Cotton straps with original style WWII
or postwar dull black plated buckles and tips;
secures MB or GPW jeep top under passenger
seat; M38, M38A1,or CJ jeep top to fender wells;
M151 jeep top under rear seat.
B1922
B1922
C1922
D1922
E1922
2A1922
2A1922
2A1922
2A1922
STRAP for securing TANDEM TOW BAR:
100% Cotton strap with original dull black
plated buckle and tip; secures tandem tow
bar to jeep grill block B2212.
B1924
----
B1924
B1924
B1924
B1924
2A1923
22
24
B1924
B1924
B1924
23
STRAP for WINDSHIELD TIE DOWN :
----
----
C1923
100% Cotton strap with original
plated dull black buckle and tip;
secures jeep windshield to hood when
in folded down position.
D1923
E1923
2A1923
2A1923
2A1923
DOORWAY BODY CANVAS FASTENERS:
B1824
B1824
Original style dull military black
finish body fastener for both doorways;
(14) sockets required MB
or GPW Half Curtains (B2307);
(4) sockets required for CJ2A doors;
(8) studs required for M38A1or M170 doors.
B1824
D1824
----
B1824
----
----
REPLACEMENT M38A1 BODY FASTENER:
Unoriginal mil-spec black body “turn” head
fastener for M38A1 doorways;
(8) studs required for M38A1 or M170 doors;
replaces Part No. D1824.
----
----
24
D1824
----
----
2A2025
WINDSHIELD STUD for late MB or GPW:
B2025-A
B2025-A
----
Steel late “capstan” style`
reproduction studs made with
permission from the original
manufacturer; don’t confuse these
with soft steel or brass foreign
reproductions available elsewhere;
set of (10) required per jeep.
(Recommended for durability over B2025-B)
WINDSHIELD STUD for early MB or GPW:
B2025-B B2025-B ----
Original style early “push button”
stud; set of (10) required per jeep.
WINDSHIELD STUD for CJ2A (NOS):
----
----
----
Original NOS black finish “turn” head
stud; set of (10) required per jeep..
WINDSHIELD STUD (Replacement):
----
Unoriginal mil-spec “turn” head black studs
with dual screw hole base fasteners which
work fine as replacements. Requires matching
grommet in top; set of (10) required per top.
HEADLIGHT COVERS (Pair):
Original style covers protect headlights &
prevent aerial observation aerial due to glass
reflection (Optional black-out slot available).
B2326-X
----
D1824
(Optional)
----
2A2025-R
2A2025-R ----
----
----
----
----
----
----
----
25R
----
----
2A2025-R
----
25A
B2025-A
B2025-B
25B
----
----
----
----
----
----
25
----
2A2025
----
----
----
----
2A2025-R ----
----
----
----
----
25R
26
B2326-X
----
----
----
M-SERIES
1" BUCKLE & TIP
----
----
----
----
27
GLOVE BOX SPARE PARTS BAG:
B2327-X
Bag carries spare parts such as spark plugs,
taillight lenses,etc. in glove or tool box.
B2327-X
B2327-X
B2327-X
B2327-X
B2327-X
B2327-X
B2327-X
B2327-X
ORIGINAL STYLE TOOL BAG:
WWII and post war issue 'envelope' style
tool bag; standard issue most vehicles.
B2328-X
B2328-X
B2328-X
B2328-X
B2328-X
B2328-X
B2328-X
B2328-X
B2328-X
RIFLE RACK COVER:
Zippered 44" long cover encloses
windshield rifle rack and fits M1 Garand rifle
& others; (specify longer if required).
B2329-X
B2329-X
B2329-X
B2329-X
B2329-X
B2329-X
C
28
B2329-X
B2329-X
B2329-X
29
TM10-3000 Page 56
CJ2A
SHOWN
2A2025
2A2025-R
36
37
2A1851
C1851
Footman
Loop
B1824
50
D1824
M38A1
SHOWN
ITEM DESCRIPTION
CIVILIAN TOP BOW STABILIZING STRAP KITS:
MB
----
----
This is an economical strap kit that replicates the function of the more expensive original top bow
2319 series support rods for stabilizing the original (6) piece
nesting1858 series CJ top bows when using only a summer top.
GPW
M38
----
---- ----
----
M38A1
----
----
M151
CJ2A
CJ3A
CJ3B
CJ5
----
----
2A1917-F
2A1917-R
2A1917-F
2A1917-R
2A1917-F
2A1917-R
2A1917-F
2A1917-R
2A0330
2A0330
2A0330
2A0330
2A0331
2A0331
2A0331
2A0331
2A1732
2A1723
2A1732
----
C1934
C1934
C1934
C1934
17
(-F ) FRONT bow to windshield, (-R) REAR bow to center bow)
FUEL TANK HOLD DOWN STRAP WELT KIT:
B0330
Pre-cut welt buffers hold down straps & tank.
B0330
C0330
D0330
----
FUEL TANK to FLOOR PAN WELT KIT:
Pre-cut welt buffers tank underside & floor.
B0331
B0331
C0331
D0331
----
RADIATOR GRILL AIR DEFLECTION KIT: Pre-cut genuine animal hair strips
used to deflect air into radiator for
MB,GPW,and CJ jeeps. M38’s kit uses
rubberized felt. (specify sheet metal
or slat grill.)
B1732
B1732
C1732
----
----
2-PIECE JERRY CAN STRAP KIT with Rivets:
Original factory style 2-piece pre-cut 100% cotton straps
rivets directly to can holder B1855.
B1934
1-PIECE JERRY CAN REPLACEMENT STRAP:
Late field style replacement for factory strap kit.
Wraps around can holder B1855 No riveting needed.
30
31
32
B1934
C1934
C1934
E1934
34
B1934-NC
B1934-NC
C1934-NC
C1934-NC
----
C1934-NC
C1934-NC
C1934-NC
C1934-NC
STANDARD WWII ISSUE VEHICLE
DOORWAY SAFETY STRAPS:
Adjustable 100% Cotton vehicle
doorway safety strap with original WWII cast
snap hooks. Typical style issue for almost
all vehicles in WWII.
B1935-B
B1935-B
B1935-B
B1935-B
E1935-B
B1935-B
B1935-B
B1935-B
B1935-B
EARLY WWII ISSUE VEHICLE DOORWAY SAFETY STRAPS WITH LEATHER:
Same as no. B1935-B except has an additional
secondary WWII buckle and leather retaining
slides; discontinued early in WWII.
B1935-C
HOOD BUMPERETTE WELT KIT:
Pre-cut welt re-lines windshield
bumperettes;protects hood; rivets included.
----
G.I. RIFLE MUZZLE COVER:
Stenciled US; issued for WWII rifles.
B2363
C
35B
B1935-C
35C
----
----
CAST SNAP HOOK
USED ON
SAFETY STRAPS
----
----
----
5E2038
E2038
B2363
B2363
B2363
B2363
SAFETY STRAP RELATED
MOUNTING HARDWARE:
B1835 BOLT & SWIVEL BRACKET (2 RPV);
B1835-EB DASHBOARD EYEBOLT (2 RPV)
38
63
----
----
----
5E2038
B2363
B2363
B2363
B2363
TM10-3000 Page 57
Build your custom CANVAS or WEB Product or Acceccesory (in an Array of Colors)
ITEM DESCRIPTION
MB
GPW
M38
M38A1
M151
CJ2A
CJ3A
CJ3B
CJ5
FENDERS & STEP-UP PADS WELT KIT:
Pre-cut welt kit used between fenders, body,
& step-up pads (One kit required per vehicle; 1 RPV).
B1739
B1739
B1739
5E1739
----
B1739
B1739
B1739
5E1739
FRAME WELT KIT:
Pre-cut welt kit used between all
contact points of the frame and
body as parts manual requires. (1 RPV)
B1540
B1540
2A1540
5E1540
----
2A1540
2A1540
2A1540
STEERING COLUMN WELT:
Pre-cut welt used between steering
column and column bracket to
buffer metal to metal contact.
B1441
39
5E1540
40
B1441
B1441
B1441
B1441
B1441
B1441
B1441
B1441
41
INNER WINDSHIELD CANVAS WELT KIT: B2042-C
Pre-cut kit seals (3) edges of MB or GPW
inner windshield to outer windshield frame. For others;
seals glass directly to outer frame. RUBBER KIT: B2042-R
B2042-C
----
----
----
----
---
----
B2042-R
3A2042
3A2042
----
B2042-R
3A2042
3A2042
3A2042
FELT PEDAL WASHER:
Felt washers prevent clutch & brake
pedals from clanging on floor pan (2 RPV).
B0244-1
B0244-1
B0244-1
B0244-1
----
B0244-1
B0244-1
B0244-1
B0244-1
BACKUP SPRING FOR B0244 WASHER:
B0244-SPG
B0244-SPG
B0244-SPG
B0244-SPG
----
B0244-SPG
B0244-SPG
B0244-SPG
B0244-SPG
TAILGATE CHAIN COVERS:
Heavy duty chain covers prevent
your tailgate chains from
rattling and chipping paint.
----
----
2A2350
----
----
2A2350
2A2350
2A2350
2A2350
FOOTMAN LOOPS:
Original style cast loop for MB or
GPW; wire stamped loop for postwar
civilian and military jeeps.
42
----
44
50
B1851-L
B1851-L
(B1851-E
for early
slat grill MB's)
C1851
C1851
(also fits MB/GPW)
2A1851
2A1851
2A1851
C1851
2A1851
2A1851
2A1851
51
B1851-L (CAST)
JERRY CAN NOZZLE SPOUT COVER:
Stops spout rattling in tool box & protects
from sand. (Stenciled 'US').
B2362
B2362
B2362
B2362
B2362
B2362
B2362
B2362
PEDESTAL SOCKET COVER:
Covers M25, M31, M31-C machine gun
pedestal opening when cradle is removed.
B2364
B2364
B2364
B2364
B2364
B2364
B2364
B2364
WINCH COVER:
Protects head on Braden WWII or Ramsey
post war winch drum and cable.
(Can be stenciled "US")
B2374
B2374
C2374
D2374
----
B2374
C2374
C2374
MIRROR COVER:
Rare accessory protects your mirror
and prevents aircraft “glint”.
B2375-X
B2375-X
B2375-X
B2375-X
B2375-X
B2375-X
B2375-X
B2375-X
B2375-X
TIRE CHAIN BAG:
Rare accessory for carrying tire
chains in your tool box; can be stenciled for
Ford or Willys jeeps. (Holds 2 chains per bag)
B2376-X
B2376-X
B2376-X
B2376-X
B2376-X
B2376-X
B2376-X
B2376-X
B2376-X
PARTS MANUAL POUCH:
Canvas or vinyl pouch for 8 1/2" x 11" parts
manual. (Actual pouch size 11"x14".)
B2382-X
MAINTENANCE MANUAL POUCH:
Canvas or vinyl pouch for 8 1/2" x 11"
maintenance manual. (Actual pouch size 8"x11".)
B2383-X
LOWER WINDSHIELD TO COWL
WEATHERSTRIP GASKET:
Heavy original style rubber gasket
that seals your outer windshield
frame to the body cowl.
(*These are interchangeable)
VEHICLE SIREN COVER:
Cover for Federal Signal Co.
vehicle siren Model EGH
C
62
64
B2362
B2364
C2374
74
76
B2382-X
B2382-X
B2382-X
B2382-X
B2382-X
B2382-X
B2382-X
B2382-X
82
B2383-X
B2383-X
B2383-X
B2383-X
B2383-X
B2383-X
B2383-X
B2383-X
83
B2086*
B2086*
3A2086*
5E2086
----
B2086*
3A2086*
3A2086*
5E2086
86
B2385
B2385
B2385
B2385
B2385
B2385
B2385
TM10-3000 Page 58
B2385
85
B2385

before you order your seat cushions

Transcription

Similar documents

Website page_GearUp Accessories Catalogue all Product

driver protection screen

2007 CADILLAC STS-V

Hedstrom 2 in 1 Swing

Early Years newsletter

It`s All About Fit

Seat Covers

The Newly Re-Designed “GS Van Package” by Sherrod:

KAMU PERSONEL SEÇME SINAVI ÖĞRETMENLİK ALAN

1971-72 Chevelle/El Camino Touring II Front