UNISAW® Accessories

Comments

Transcription

UNISAW® Accessories
UNISAW ® Accessories
DELTA and BIESEMEYER products can be found on www.DeltaMachinery.com
®
®
U NI SAW ® Accessories
36-201
36-055
36-050
36-0101
Standard & Dado
Arbor Nut Assembly
Feather Board
Push Stick
Table Saw
Arbor Wrench
»» For single-blade operations, an arbor
nut coupled with a 5/16 in. x 2 1/2 in.
dia. machined steel flange provides
rigid blade stabilization
»» For stacked dado applications,
switch to the separate arbor nut
without a flange
»» Universal T-track compatibility for
»» Device used to push stock while
»» Design allows stock to pass in one
»» Designed to optimize control of your
improved cut control
direction and causes resistance
if moved in the other direction;
preventing kickback
keeping hands away from the blade
»» Extra-long handle keeps your hand
away while changing the blade
workpiece
»» Each features a wide knurled grip
with hex-head for final tightening
36-805
36-0944
Standard
Replacement
Throat Plate
Zero Clearance
Throat Plate
»» Designed to support the material on
both sides of the saw kerf to prevent
tearout
»» 1/2 in. thick melamine-coated solid
36-808
50-479
Dado Throat Plate
5 in. to 4 in. Port
Reducer
»» For use with stacked dado cutters
»» Phenolic construction for minimal
tearout
»» This fitting allows you to reduce down
from a larger main line to smaller
branch lines
phenolic resin blanks
78-967
78-965
34-568
34-928
BIESEMEYER®
Medium and Thick
Kerf Riving Knife
BIESEMEYER®
Thin Kerf Riving Knife
Clamp Attachment
Deluxe Miter Gauge
»» Holds work securely for accurate
»» Designed with the
»» For use with Model 34-928 miter gauge
»» Oversized grip and positive
miter and cut-off operations
professional in mind
stops at all popular miter angles
DELTA and BIESEMEYER products can be found on www.DeltaMachinery.com
®
®
U NI SAW ® Accessories
78-9450
50-2000 / 50-257
BIESEMEYER® Rear Outfeed Table
Mobile Base
»» Adds an additional 4 ft. x 44 in. of work support
»» Compatible with any DELTA® UNISAW® or other DELTA® 12 in. or 14 in. saws
»» Enhances mobility in the workshop
»» 50-2000 for use with older model UNISAW®
»» 50-257 for use with 36-L352 or 36-L552 UNISAW® models
78-864B / 78-918B
78-138B / 78-055B
BIESEMEYER® Universal Table Board
BIESEMEYER® Fence Rails
78-864B – For the 36 in. BIESEMEYER® Fence System
Table Board L X W X H: 37 in. X 35 1/2 in. X 4 1/2 in.
78-918B – For the 52 in. BIESEMEYER® Fence System
Table Board L x W x H: 52 in. x 37 in. x 4 1/2 in.
78-138B – For 36 in. BIESEMEYER® Fence System
78-055B – For 52 in. BIESEMEYER® Fence System
»» Constructed of a hardwood alder frame and laminated particle board
»» Laminate siding on three sides
»» Backer-board underside
DELTA and BIESEMEYER products can be found on www.DeltaMachinery.com
®
®
Premium Accessories
78-919B
78-939
BIESEMEYER®
Fence System
BIESEMEYER®
Cut-off Fence
»» Quick-release clamp for fast
»» The most precise fence in the industry
»» Fence body constructed from .083
and safe setups
»» Acts as a stand off to keep material
gauge steel
away from the fence when using
a miter gauge
»» Laminated 9-ply Birch plywood sides
are durable and do not mar easily
»» Smooth sliding surface. The one
»» Accurate repeatability, eliminating
78-970
BIESEMEYER®
Standard
Accessory Drawer
»» Storage designed for the woodworker
»» Easily accommodates up to five saw
blades, two riving knives, throat plate,
push stick, wrench/ arbor nut and
complete guarding assembly
inch dimension can be easily added
when indexing the hairline on your
BIESEMEYER® fence with the scale on
the system ft.s guide
the need for using a hand-held tape to
square and set the fence
78-940
34-184
BIESEMEYER®
Auxiliary Fence
Universal
Tenoning Jig
»» Has ergonomic handles, quick release
coarse adjustment, micro adjustment
to .004 in.
»» Universal miter bar for use with all
table saws with
»» 3/8 in. x 3/4 in. miter slots
50-786
50-531
50-530
4 in. x 20 ft. Hose
4 in. x 10 ft. Hose
The Perfect
1.5 HP Dust Collector
for the DELTA UNISAW
DELTA and BIESEMEYER products can be found on www.DeltaMachinery.com
®
®
®
®
Service Parts
Service Part A28410
Service Part A28414
Rise-and-Fall Split
Guard Assembly
Anti-Kickback Pawls
»» Tool-free split guard design allows
easier line of site with the blade and
work-piece
»» Design allows stock to pass in
one direction and causes resistance
if moved in the other direction;
preventing kickback
ServiceNet is the Official
Parts & Service Site For DELTA® and is
your one-stop for all your parts needs.
www.DeltaMachinery.com/parts
Riving Knife Selection
The riving knife supplied with the DELTA® UNISAW® is the correct size for the blade supplied with the saw. If a different blade is used,
check the blade body, or plate, thickness and the blade kerf, or cutting width marked on the blade or on the blade packaging. The riving
knife thickness must be greater than the body thickness and less than the kerf width as shown in Fig. 1. If it is not, the riving knife MUST
be replaced with one that has the correct thickness. The riving knife provided with this saw is marked as follows: 2.2 mm THICK RIVING
KNIFE. ONLY USE FOR 10 in. BLADE WITH 2.4 mm minimum KERF WIDTH AND 1.7 mm maximum BODY THICKNESS. (See Fig. 2) The riving
knife (available as an accessory from DELTA®) is marked as follows: 2.8 mm THICK RIVING KNIFE. ONLY USE FOR 10 in. BLADE WITH 3.0
mm minimum KERF WIDTH AND 2.5 mm.
MAX. BODY THICKNESS–All DELTA® blade body thickness and kerf widths are provided at www.DeltaMachinery.com. If a different
blade is used and the body thickness and kerf width dimensions are not provided, use the following procedure to determine the correct
riving knife thickness:
»»
»»
»»
»»
STEP 1: Measure the body thickness of the blade.
STEP 2: Make a shallow cut in scrap material and measure the kerf width.
STEP 3: Select the riving knife as shown in Fig. 1.
STEP 4: Slide the riving knife through the shallow cut (Fig. 3) made in step 2 to confirm the correct riving knife has been selected. The riving knife should not bind or drag through the cut.
IMPORTANT NOTE: If any dragging or binding of the material is encountered as it reaches the riving knife, turn unit off and disconnect machine from power
source. Repeat steps 1–4 to make the proper riving knife selection before attempting another cut.
DELTA and BIESEMEYER products can be found on www.DeltaMachinery.com
®
®
Copyright © 2012
DELTA® Power Equipment Corporation
92-393B - 03-01-2012