EX750 QIG ver1.0

Product Introduction
Quick Installation Guide
AC750 Dual Band WiFi Range Extender
Model No.: EX750
Power: The indicator keep lighting after powered on.
CPU: The indicator is blinking after powered on, keep fast
blinking after the RST button pressed.
5G EXT: The indicator is blinking when searching for
primary AP, keep lighting when connected.
2.4G EXT: The indicator is blinking when searching for
5G WPS: Press this button for 5G WiFi network extension.
2.4G WPS: Press this button for 2.4G WiFi network
RST: Press this button for more than 5 seconds, the
LNK/ACT: The indicator will keep lighting when
extension.
device will be reset to factory default settings.
connected.
V1.1501
Copyrights
ON/OFF: Slide this switch to power on or off the device.
primary AP, keep lighting when connected.
LAN Port: This port is used to connect the PC.
2015 by TOTOLINK All rights reserved. Website: http://www.totolink.net
Information in this document is subject to change without prior notice.
Method One: WiFi Extension by WPS button
One-click WPS connection makes it easy to extend the coverage of your existing WiFi network. Here we take A2004NS as primary Router.
Press the WPS button on the router for 2 seconds.
(SSID: TOTOLINK A2004NS)
Then press the WPS button on the router for 2 seconds again.
(SSID: TOTOLINK A2004NS_5G)
Press the 2.4G WPS button on EX750 for 2 seconds. Wait for a while.
Until the 2.4G EXT indicator turns solid lighting, 2.4G WiFi network
extending successfully. (SSID: TOTOLINK EX750)
Press the 5G WPS button on EX750 for 2 seconds. Wait for a while.
Until the 5G EXT indicator turns solid lighting, 5G WiFi network extending
successfully. (SSID: TOTOLINK EX750_5G)
SSID: TOTOLINK EX750
SSID: TOTOLINK EX750
TIPS:
You can put EX750 close
the router to setup WPS
connection, then unplug it
and place it anywhere within
the WiFi coverage. EX750
can remember the last
connected AP and firstly
connect to it when powered
on.
5G
2.4G
WPS
WPS
Method Two: Setup via Web Interface
1 Setup your PC (Connect your PC to the LAN port of EX750)
:
Right-click “ Network — Properties
— Local Area Connection — Properties”.
Double-click “Internet Protocol
Version 4 (TCP/IPv4)”
2 Setup the EX750
:
Open any browse, type in 192.168.0.254, press Enter key.
Choose “Use the following IP address”,
IP address: 192.168.0.5, default
gateway: 192.168.0.254. Click OK--OK.
Below the Web Interface of EX750 shows up. First click 2.4GHz Extender Setup.
Click Setup Tool:
5
By default, AP mode selected.
Click LOGIN, the Web settings page shows up. Choose your upper router’s
SSID, here we choose zion.
6
Choose Extender (AP + Client) mode.
8
Select primary router’s SSID, then type in the correct Encryption key (password)
of the router. Click Apply.
10
Next, please do the same operation for 5GHz Extender Setup: Choose
Extender (AP + Client) mode, click AP Scan button. Select primary router’s SSID,
then type in the correct Encryption key (password) of the router. Click Apply.
7
click AP Scan button on right top of the page, then many SSIDs will
turn up for you to choose.
9
After a moment, it shows connected.
11
You can check the EX750’s status on Status Summary page, see below:
For more information, please go to www.totolink.net
12
Try any website to test the Internet.
NOTE
NOTE: EX750 allows you to change the extended SSID for extender.
So that you can keep a separated SSID for extending WiFi network,
not same as primary router.