110907 - Hustler Turf

Hustler Sport
Parts Manual
•••••••
Hustler Turf Equipment
•••••
P.O. Box 7000
•••
Hesston, Kansas
•
67062-2097
WARNING:
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.
NOTICE OF REQUIREMENT OF SPARK ARRESTER MUFFLER
This equipment may create sparks that can start fires around dry vegetation. California Public Resources Code Section 4442.6 provides that it is unlawful to use or operate an internal combustion engine on any forest-covered,
brush-covered, or grass-covered land unless the engine is equipped with a spark arrester maintained in effective
working order. A spark arrester is a device constructed of nonflammable materials specifically for the purpose of
removing and retaining carbon and other flammable particles over 0.0232 of an inch in size from the exhaust flow of
an internal combustion engine that uses hydrocarbon fuels or which is qualified and rated by the United States Forest Service. Other states or federal areas may have similar laws. The Operator Should Contact Local Fire Agencies
For Laws or Regulations Relating to Fire Prevention Requirements. THIS EQUIPMENT DOES NOT HAVE A
SPARK ARRESTER AND YOU SHOULD CONTACT YOUR AUTHORIZED DEALER FOR THE PURCHASE OF A
SPARK ARRESTER.
Inspect spark arrester daily; replace every 500 hours or as needed.
The Engine Owner’s Manual provides information regarding the U.S. Environmental Protection Agency
(EPA) and the California Emission Control Regulation of emission systems, maintenance and warranty.
Keep Engine Owner’s Manual with your unit. Should the Engine Owner’s Manual become damaged or illegible, replace immediately. Replacements may be ordered per the information found in the Product Information section of the owner’s manual.
t-2
110907 07/10
Table of Contents
Section 1
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 2 Contents
Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Additional California Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 3 Contents
Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering Sub-Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Park Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 4 Contents
Wheel & Tire—42/48" Decks . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel & Tire Breakdown—42/48" Decks . . . . . . . . . . . . . . . . . . . .
Wheel & Tire—54" Decks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel & Tire Breakdown—54" Decks . . . . . . . . . . . . . . . . . . . . . .
Section 5 Contents
Engine, 17 HP/ 21 HP Briggs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine, 26 HP Briggs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine, Honda GXV 530. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 6 Contents
Instrument Panel, 17/21 Briggs. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel, 26 Briggs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel, Honda . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Schematic—Briggs (601676). . . . . . . . . . . . . . . . . . . . . .
Electrical Schematic—Honda GXV 530 (602096). . . . . . . . . . . . . .
Section 7 Contents
42" Deck Decals—Forward Swept . . . . . . . . . . . . . . . . . . . . . . . . .
42" Deck Decals—Rear Swept . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48" Deck Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
54" Deck Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
42" Deck Pulleys and Spindles—Forward Swept . . . . . . . . . . . . . .
Deck Pulleys and Spindles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48" Deck Pulleys and Spindles . . . . . . . . . . . . . . . . . . . . . . . . . . . .
54" Deck Pulleys and Spindles . . . . . . . . . . . . . . . . . . . . . . . . . . . .
42" Deck—Forward Swept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
42" Deck—Forward Swept Belt Routing & Tensioning . . . . . . . . . .
42" Deck—Rear Swept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
42" Deck—Rear Swept Belt Routing & Tensioning. . . . . . . . . . . . .
48" Deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48" Deck Belt Routing & Tensioning . . . . . . . . . . . . . . . . . . . . . . . .
54" Deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
54" Deck Belt Routing and Tensioning . . . . . . . . . . . . . . . . . . . . . .
DeckLift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deck Mounting Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
110907 07/10
c-1
1-1
2-2
2-4
2-5
3-2
3-6
3-8
3-14
4-2
4-4
4-6
4-8
5-2
5-4
5-6
5-8
6-2
6-4
6-6
6-8
6-10
6-11
7-2
7-4
7-6
7-8
7-10
7-12
7-14
7-16
7-18
7-20
7-22
7-24
7-26
7-28
7-30
7-32
7-34
7-36
Section 8 Contents
Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i-1
c-2
110907 07/10
Section 1
General Information
This Manual covers Hustler Sport models 929125, 929125CA, 929133, 929133CA, 929463,
929471, 929596, 929851 & 929869.
Frequently Ordered Parts
PART NO.
769133
600726
777185
601123
601846
601848
602570
601845
602572
785626
DESCRIPTION
PART NO.
Pump Drive Belt
Deck Belt 42"
Deck Belt 54"
Blade, 16.50"-L-F-CW
Filter, Air Precleaner, 17.5 HP Briggs
Filter, Air Precleaner, 21 HP Briggs
Filter, Air Cartridge, 26 HP Briggs
Engine Oil Filter 17.5/21 HP Briggs
Engine Oil Filter 26 HP Briggs
Fuel Filter, Honda
DESCRIPTION
771634
601124
793794
601847
601849
602571
068478
787234
787226
Deck Belt 48"
Blade, 18.50"-L-F-CW
Blade, 20.50"-L-F-CW
Filter, Air Flat Panel, 17.5 HP Briggs
Filter, Air Cartridge, Briggs
Filter, Air Precleaner, 26 HP Briggs
Fuel Filter In-Line, Briggs
Engine Oil Filter, Honda
Air Filter, Honda
PART NO.
DESCRIPTION
Options Available From Your Dealer
PART NO.
929216
929828
929836
112614
112615
DESCRIPTION
Catcher, 2-Bag 42" Sport
Catcher, 2-Bag 48" Sport
Catcher, 2-Bag 54" Sport
Containment Kit, 48"
Containment Kit, 54"
111164
112609
112611
111167
110737
Mulch Kit, 48" Sport
Mulch Kit, 42" Sport
Mulch Kit, 54" Sport
Hour Meter Kit
Sport LED Light Kit
Service Literature
PART NO.
DESCRIPTION
111176
601865
601866
602607
787242
Hustler Sport Owner’s Manual
Briggs & Stratton 17.5 HP Engine Manual
Briggs & Stratton 21 HP Engine Manual
Briggs & Stratton 26 HP Engine Manual
Honda 16 HP Engine Manual
Note: When ordering parts, you must use the part number as shown for each part, not the item number. Always give
the model and serial number to your parts and service representative.
Note: Items sold in bulk such as seals and hoses are sold by the foot.
110907 07/10
1-1
Using this manual
Illustrations used were current at the time of printing, but subsequent production changes may cause your machine to
vary slightly in detail. Excel Industries, Inc. reserves the right to redesign and change the machine as deemed necessary, without notification. If a change has been made to your machine which is not reflected in this parts manual, see
your Hustler dealer for current information and parts.
Hardware Description Codes & Abbreviations
The following codes are used throughout this parts manual. Refer to this list when ordering parts.
ABBREVIATION
CB
CE
CP
CN
CS
CW
FDRW
FW
HX
LW
DESCRIPTION
ABBREVIATION
Carriage Bolt
Clevis Pin
Cotter Pin
Clip Nut
Cap Screw
Cup Washer
Fender Washer
Flat Washer
Hex Head
Lock Washer
MB
MS
NT
SC
SH
SB
SS
OD
ID
DESCRIPTION
Machine Bushing
Machine Screw
Nut
Self Tapping Cap Screw
Socket Head
Shoulder Bolt
Set Screw
Outside Diameter
Inside Diameter
Standard Torques
The following chart lists the standard torque values for the threaded fasteners found in this manual. Torque all cap
screws, nuts and set screws to these values unless a different torque is shown in the Notes section next to the fastener
SIZE
FT-LBS
NM
SIZE
FT-LBS
NM
.250
.312
.375
.438
.500
.562
.625
.750
.875
1.00
8.2
17
30
48
73
105
145
260
420
625
11.1
23
40
65
99
143
200
350
565
850
M3
M4
M5
M6
M8
M10
M12
M16
M20
M24
1
2.2
4.5
7.7
18.5
37
64
160
320
555
1.3
3
6.1
10.4
25
50
87
215
435
750
NOTE:
Loctite 592 to be used on all pipe threads.
Lubricate all grease zerks.
1-2
110907 07/10
Section 2 Contents
Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Additional California Decals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Engine Guard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
110907 07/10
2-1
Frame
1
2
3
4
5
2
14
6
13
11
10
12
1
9
15
6
16
7
2-2
1
3
8
110907 07/10
Frame
INDEX NO.
PART NO.
QTY.
1
550249
1
550248
1
FRAME, SPORT
2
808485
1
RIVET NUT, 5/16-18 THREAD
3
600899
1
PUMP BELT WARNING DECAL
4
785220
1
STEERING DECAL
5
727172
1
'MADE IN U.S.A.' DECAL
6
601986
2
STEP TREAD, LOWER SPORT
7
601813
1
HUSTLER DECAL FRONT
8
601981
1
SAFE OPERATION DECAL
9
601812
1
SPORT ID DECAL
10
782573
1
FIRST ZERO TURN DECAL
11
785139
1
STEERING DECAL
2
3
DESCRIPTION
FRAME, SPORT
12
N/A
1
SERIAL NO PLATE TURF
13
601967
1
ENGINE COMPARTMENT DECAL
14
602041
1
HOT DECAL
15
110063
2
GRIP TAPE
16
601987
1
STEP TREAD, FOOT LIFT
NOTES:
1. In the event the serial number tag becomes damaged or illegible, please
contact your Hustler dealer to order a replacement.
2. Illustration shows frame used on 929133, 929133CA, 929471 & 929596.
3. Illustration shows frame used on 929125, 929125CA, 929463, 929851 &
929869.
110907 07/10
2-3
Additional California Decals
2
1
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
083279CA
1
DECAL, CA EMISSIONS
2
601908
1
DECAL, SPARK ARRESTOR
NOTES:
1. In the event the serial number tag becomes damaged or illegible, please
contact your Hustler dealer to order a replacement.
2-4
110907 07/10
Engine Guard
1
2
3
3
4
INDEX NO.
PART NO.
QTY
DESCRIPTION
1
112849
1
BUMPER GUARD PLATE
2
016428
2
CS .375-16 X 2.50 HX GR5
3
767954
4
FW .406 X .812 X .060 SAE
4
086660
2
NT .375-16 HXZY NL
NOTES:
1. This guarding is used only on mowers with Briggs & Stratton 26 HP
engine.
110907 07/10
2-5
2-6
110907 07/10
Section 3 Contents
Hydraulic System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Steering Sub-Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Park Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
110907 07/10
3-1
Hydraulic System
1
2
3
4
5
6
8
12
10
7
3
11
9
10
1
10
12
10
3-2
110907 07/10
Hydraulic System
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
043067
4
2
710087
4
CS .312-18X2.500 HX G5
3
768523
16
FW .343X.687X.051/.080H
4
793174
2
TOWLINK ROD
5
048553
2
CP .062DX1.000 LG HML Z
6
601391
2
EZT, 19.2 RIGHT TRANSMISSION
7
601390
1
EZT, 19.2 LEFT TRANSMISSION
8
110042
1
HYDROSTAT CROSS BRACE
CS .375-16X2.250 HX G5 ZN
CS .312-18X3.00 HX G5 Z
9
056036
4
10
767954
8
FW .406 X .812 X .060 SAE HRD ZN
11
034272
8
NT .312-18 HX G5 ZN
12
054502
4
NT .375-16 HX G5 ZN
NOTES:
1. Torque to 17 ft-lbs.
2. Service parts available for the transaxles:
PART
NUMBER
110907 07/10
PART
NUMBER
DESCRIPTION
DESCRIPTION
788877
IZT, HUB NUT
798371
RING, RETAINING
788232
IZT, HUB ASSEMBLY
601941
FAN/PULLEY KIT
798363
GEAR, PARK BRAKE
795047
PARKING PAWL KIT, EZT
3-3
Hydraulic System
13
3
14
15
16
21
17
18
22
19
15
15
23
20
24
3-4
110907 07/10
Hydraulic System
INDEX NO.
PART NO.
QTY.
DESCRIPTION
13
017616
1
CS .500-13X1.75 HX GR5 ZN
14
601983
1
CS .625-11 X 2.25 HX G5 ZY
15
028118
3
FW .625X1.00X.134 ZNYC
16
036384
1
SPRING 1/4 COIL PL 1.23
17
111079
1
PUMP IDLER, FORMED
18
601398
1
SPACER, PUMP IDLER
19
784827
1
IDLER PULLEY, 4.00"OD
20
016972
1
NT .625-11 HX G5 ZNYC
21
602026
2
BEARING DISC
22
602025
1
BUSHING, IGUS .500 I.D.
23
781567
1
NT .500-13 HX G8 ZY NL
24
769133
1
BELT, A 67.24" EL
NOTES:
3. Torque to 100 ft-lbs.
Hydraulic pump belt adjustment
The transaxle drive belt tension remains constant by means of a tension idler and spring. There is no
tension adjustment of this belt.
NOTE:
Inspect the belt every 100 hours and replace as needed. Replace the belt
every 200 hours or every two (2) years whichever comes first.
WARNING: If the transaxle belt fails, loss of control will occur especially when operating on a slope. If
you lose steering control while operating the machine, place the steering control levers in the park
brake position immediately. Inspect the machine and involve your Hustler dealer to resolve the
problem before continuing to operate.
110907 07/10
3-5
Steering
1
Steering
Sub-Assembly
2
3
3
4
3
6
5
8
3
9
3
7
10
3
7
3
3
4
3-6
110907 07/10
Steering
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
600221
2
STEERING DAMPER
2
781922
4
BALL STUD, DAMPER
3
768523
17
FW .343X.687X.051/.080H
4
023655
4
NT .312-24 HXZY NL
5
784439
2
LOCK COLLAR,0.757 ID
6
600981
2
PUMP ROD ASSEMBLY
7
034272
4
NT .312-18 HX G5 ZNYC
8
034280
1
CS .312-18X .750 HX G5
9
110014
1
PIVOT TUBE ASSEMBLY
10
029876
2
LW .312 INT-EXT TOOTH Z
NOTES:
1. Service parts for Damper:
PART
NUMBER
110907 07/10
DESCRIPTION
601425
CONNECTOR BODY
601426
CAP LOCK
3-7
Steering Sub-Assembly
1
2
2
6
3
4
4
5
7
4
10
4
5
9
11
12
13
14
12
3-8
110907 07/10
Steering Sub-Assembly
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
781260
2
2
110370
2
STEERING BAR
3
054502
4
NT .375-16 HX GRD 5 ZNY
4
767954
12
FW .406X .812 X.060 SAE
5
770867
4
BUSHING, PLAS .750X1(FS)
6
086660
2
NT .375-16 HXZY NL
7
110008
1
STEERING BOX LH
8
110007
1
STEERING BOX RH (NOT SHOWN)
GRIP, STEERING BAR
9
705178
2
CS .375-16X1.750 HX G5
10
080655
4
CS .375-16X1.500 HX G5
11
110089
2
CONTROL LEVER
12
768523
4
FW .343X.687X.051/.080H
13
796615
2
BALL JOINT LINK
14
023655
2
NT .312-24 HXZY NL
NOTES:
1. Left side steering sub-assembly is shown; the right side is similar.
2. Item 2 (Steering Bar) includes Item 1 (Steering Bar Grip).
110907 07/10
3-9
Steering Adjustments
Steering linkage
The neutral adjustment for the control levers in the neutral position is discussed in this section.
The tractor steering has been factory adjusted to eliminate creeping when the control levers are in the
neutral position (FIG. 1). However, should the mower begin to creep, the control lever linkage can be
adjusted as follows:
CONTROL
LEVER
CONTROL LEVER IN THE
NEUTRAL POSITION
FIG. 1
CONTROL LEVER NEUTRAL ADJUSTMENT
Before considering any adjustment, check the tire air pressure. Unequal tire pressure will cause the mower
to drift to one side. Refer to tire pressure information in the Maintenance section of this manual.
NOTE:
Proper park brake adjustment must be completed before the control lever
neutral adjustment can be done.
Fine adjustment to the unit’s steering is made with the transaxle control rod. (FIG. 2).
Neutral is properly adjusted when the control levers are in the park brake position and the ZT 2800
transaxles do not “whine”.
If this occurs, the control linkage may be adjusted as follows:
1. Park the unit on a flat surface, raise the rear of the mower and block with certified jack stand. With the park brakes
set, start the engine (FIG. 2). Once the engine is started, if the ZTs whine while the park brake is engaged, then
neutral needs to be reset. Turn off the engine.
WARNING: Never work under the machine or attachment unless it is safely supported with jack
stands. Make certain machine is secure when it is raised and placed on the jack stands. The jack
stands should not allow the machine to move when the engine is running and the drive wheels are
rotating. Use only certified jack stands. Use only appropriate jack stands, with a minimum weight
rating of 2000 pounds to block the unit up. Use in pairs only. Follow the instructions supplied with the
vehicle stands.
WARNING: This is a dangerous operation - keep hands, hair, clothing, etc., clear of the cooling fans
on top of the ZTs! Exercise extreme caution.
WARNING: .Never attempt to make any adjustments or repairs to the mower drive system while the
engine is running. The following procedures should be performed by trained maintenance
personnel only.
2. Loosen and back off the jam nuts on both ends of the steering control rod assembly (FIG. 2). Set the steering control lever in the neutral/brake position.
3-10
110907 07/10
CONTROL LEVER IN THE
NEUTRAL POSITION
CONTROL LEVERS IN PARK BRAKE POSITION
DAMPER
JAM NUT
STEERING
CONTROL ROD
JAM NUT
FIG. 2
FIG. 3
STEERING
DAMPER
ENGINE
GUARD
JACK STANDS
REAR DAMPER
BALL STUD
FIG. 4
FIG. 5
3. Remove the female spade connectors from the seat switch (located under the seat). These will need to be connected together now to bypass the seat switch to perform the following functions. This must only be done by a
qualified Hustler Dealer.
4. Make sure the steering damper ball studs attached to the frame at the rear of the damper on either side are loose
and allowed to slide in the slot.
5. Both steering control levers need to be in the brake position when starting the engine, but need to quickly be
moved out of the brake position once engine is started so the brakes do not fight the transmissions since they have
not yet been adjusted.
6. Start the engine. Move the control lever to just engage the brake (neutral) slot and hold it in that position (Do not
engage the control lever far enough to engage the brakes in the brake slot) (FIG. 3).
WARNING: This operation is extremely dangerous. Pay close attention when adjusting the
transaxle control rod so you do not get your fingers, tools, or anything else close to the EZT
transaxle’s cooling fans.
7. Beginning with the RH side of the mower, adjust the steering control rod so that the RH drive axle just starts turning
in the forward rotation while the steering lever remains in the neutral positon. Now, turn the steering rod back the
opposite direction to the point when the drive axle stops spinning. From that point, turn the steering rod back again
½ turn. This ensures that the steering rod is adjusted so that the transmission control arm is centered in the neutral
band of the transmission.
110907 07/10
3-11
8. Move the lever forward and backward and make sure that the drive axle spins forward and backward correctly.
Return the steering lever to neutral and re-check to make sure the drive axle is stopped in the neutral position.
Lock the steering control lever into the brake position. You should not hear the transmission whine if neutral is
properly set.
9. Turn off the engine.
10. With the engine off, move the RH steering control lever into the neutral position and pull the lever all the way back
to the rear of the mower as if you were going full speed in reverse. Now, slowly bring the lever back to the neutral
position and lock it into the brake position. This sets the steering damper in the correct neutral position. Tighten
the ball stud at the rear of the damper that is attached to the frame side panel on the RH side (FIG. 5). Once this
is tightened, you should be able to move the steering control lever to the reverse position, let it go, and the steering
lever should return itself to the neutral position. This should finish the adjustment for the RH side steering control.
Double check to make sure you have all fasteners tightened to the correct torque specifications.
11. Repeat steps 4 thru 9 for the LH side.
12. Once both sides are properly adjusted, double check them together to make sure everything is working properly.
13. IMPORTANT: With the engine off, disconnect the two female spade connectors from each other (from step #3)
and reconnect them to the seat switch. This must be completed so the safety circuit is functioning properly. Refer
to the machine’s owner’s manual for operation check.
WARNING: Do not operate the mower without plugging the mower wiring harness into the seat
switch. This switch is an important part of the safety start interlock system. Serious injury can result
if the seat switch is not plugged into the mower’s wiring harness.
14. Check to make sure all tools or obstructions are removed from under the mower. Assemble the drive wheels and
lugnuts. Torque the lugnuts to 65-75 ft-lbs.
15. Jack up the rear of the mower and remove the jack stands. Lower the mower to the ground and remove the jack.
16. The control levers should be adjusted so that they align vertically with each other when in the neutral position.
Space between ends of control handles to be .50" ±.25".
17. Check the hydraulic oil level after final adjustments. Make sure oil level is within operating range specified.
Steering damper
The steering damper (FIG. 5) is spring loaded to return the control levers to the neutral position from the
reverse position. This gives the operator a sense of neutral during operation.
If the mower does not return to neutral from reverse then adjust as follows:
To set the steering dampers in the correct operating position follow these steps:
1. Shut engine off, place control levers in the park brake position, disengage deck clutch, remove ignition switch key
and disconnect negative battery cable before doing any adjustments.
2. Place the control lever in the neutral position (FIG. 1).
3. Loosen the steering damper’s rear ball stud (FIG. 5).
4. Pull the damper spring housing, to the rear, past the point that the internal spring is engaged.
5. Release the damper spring housing and allow the internal spring to bring the housing back to the neutral position.
6. Tighten the nut on the steering damper’s rear ball stud.
7. To check, move the control lever to the reverse position and release. The control lever should return to the neutral
position. If not, repeat steps 1 through 6.
3-12
110907 07/10
This page intentionally left blank.
110907 07/10
3-13
Park Brake
CONNECTS TO
STEER PIVOT
14
1
3
BELL
CRANK
DETAIL
4
5
15
16
6
7
7
8
9
10
11
12
10
13
3-14
110907 07/10
Park Brake
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
110001
1
2
110000
1
BRAKE ACUTATOR RH (NOT SHOWN)
3
765339
4
BUSHING,IGUS#0608 (FS)
4
601822
2
NUT PLATE, .420 CENTERS
5
781211
2
SWITCH, PUSH BUTTON(FS)
6
086660
2
NT .375-16 HXZY NL
7
767954
4
FW .406X .812 X.060 SAE
8
725796
2
CS .375-16X4.00 HX G8 Z
BRAKE ACTUATOR LH
9
063198
4
CS 10-24X .750 HXFLK ZN
10
068551
4
NT .250-20 HXZY NL
11
768515
4
FW .281X.625X.051/.080H
12
601131
2
SPRING, BRAKE ARM RET.
13
110009
2
BRAKE ACTUATOR ROD
14
048553
2
CP .062DX1.000 LG HML Z
15
768523
8
FW .343X.687X.051/.080H
16
023655
2
NT .312-24 HXZY NL
NOTES:
PARK BRAKE SPRING ADJUSTMENT
NOTE:
method:
Occasionally check the park brake spring adjustment using the following
1. Shut engine off, place control levers in the park brake position,
disengage deck clutch, remove ignition switch key and disconnect
negative battery cable before doing any adjustments.
2. Position the control lever in the park brake position.
3. Measure the park brake spring. It should be compressed to 1.00”. If it is
not, adjust the nylock nut until the proper spring compression is
achieved (FIG. 6).
1.00"
0.25"
NYLOCK NUT
NYLOCK NUT
BRAKE ARM
SPRING
FIG. 6
4. Repeat for the other side.
110907 07/10
3-15
3-16
110907 07/10
Section 4 Contents
Wheel & Tire—42/48" Decks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Wheel & Tire Breakdown—42/48" Decks . . . . . . . . . . . . . . . . . . . . . 4-4
Wheel & Tire—54" Decks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Wheel & Tire Breakdown—54" Decks . . . . . . . . . . . . . . . . . . . . . . . . 4-8
110907 07/10
4-1
Wheel & Tire—42/48" Decks
15
10
3
17 10
16
2
1
4
4
2
6
2
7
1
8
9
3
5
10
14
10
11
12
13 2
3
4-2
110907 07/10
Wheel & Tire—42/48" Decks
INDEX NO.
PART NO.
1
788166
2
ANTI-SCALP WHEEL ASSEMBLY
2
344267
6
FW .510X 2.15X.187 SPL
3
781567
4
NT .500-13 HX G8 ZY NL
4
601810
2
TIRE/WHEEL 18X8.5-8
5
061077
8
WHEEL NUT
6
705954
2
CS .500-13X1.25 HX G5 Z
7
712976
2
FW .531X 1.375X.125 ZNY
8
784223
4
BEARING
SPACER
5
5
QTY.
DESCRIPTION
9
784603
2
10
767962
8
FW .531X 1.063X.090 SAE
11
042630
2
CS .500-13X6.50 HX G5 Z
12
306969
2
GAGE WHEEL SPACER
TIRE/WHL 11X4-5 RIBBED
13
602079
2
768044
2
TIRE/WHL 11X4-5 RIBBED
110116
2
CASTER FORK
339689
2
CASTER FORK
15
781708
2
CS .500-13X4.250 HX G5
16
031997
2
ANTI-SCALP WHEEL
17
053199
2
NT .500-13 HX JAM ZNYC
14
NOTES:
1. Torque to 65-75 ft. lbs.
2. Inflate tire to 8-12 psi.
3. Apply grease to zerks (see owners manual).
4. Item 1 includes (items 10 &15–17).
5. Serial numbers higher than 09080553, use tire/wheel (602079 ) and
caster fork (110116). Serial numbers prior to 09080553, use tire/wheel
(768044 ) and caster fork (339689).
110907 07/10
4-3
Wheel & Tire Breakdown—42/48" Decks
601
810
1
2
3
Fro
nt W
hee
l
4
5
4
4-4
110907 07/10
Wheel & Tire Breakdown—42/48" Decks
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
601821
1
TIRE 18 X 8.5 - SPORT
2
601820
1
WHEEL 8 X 6.93 - SPORT
3
019521
1
TIRE VALVE TR-412 GOODY
4
772806
2
BEARING CAPS
5
772814
1
BEARING, 3/4" ROLLER
NOTES:
110907 07/10
4-5
Wheel & Tire—54" Decks
15
10
3
17 10
16
2
1
4
4
2
6
2
7
8
1
5
9
3
10
8
14
10
11
12
13 2
3
4-6
110907 07/10
Wheel & Tire—54" Decks
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
788166
2
ANTI-SCALP WHEEL ASSEMBLY
2
344267
6
FW .510X 2.15X.187 SPL
3
781567
4
NT .500-13 HX G8 ZY NL
4
784264
2
TIRE/WHEEL 18X9.5
5
061077
8
WHEEL NUT
6
705954
2
CS .500-13X1.25 HX G5 Z
7
712976
2
FW .531X 1.375X.125 ZNY
8
784223
4
BEARING
SPACER
9
784603
2
10
767962
8
FW .531X 1.063X.090 SAE
11
042630
2
CS .500-13X6.50 HX G5 Z
12
306969
2
GAGE WHEEL SPACER
13
602079
2
TIRE/WHL 11X4-5 RIBBED
14
110116
2
CASTER FORK
15
781708
2
CS .500-13X4.250 HX G5
16
031997
2
ANTI-SCALP WHEEL
17
053199
2
NT .500-13 HX JAM ZNYC
NOTES:
1. Torque to 65-75 ft. lbs.
2. Inflate tire to 8-12 psi.
3. Apply grease to zerks (see owners manual).
4. Item 1 includes (items 10, 15 & 16).
110907 07/10
4-7
Wheel & Tire Breakdown—54" Decks
784
264
1
2
3
602
0
79
4
5
4
4-8
110907 07/10
Wheel & Tire Breakdown—54" Decks
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
784272
1
TIRE 18 X 9.5-8
2
784280
1
WHEEL 8 X 6.23
3
019521
1
TIRE VALVE TR-412 GOODY
4
772806
2
BEARING CAPS
5
772814
1
BEARING, 3/4" ROLLER
NOTES:
110907 07/10
4-9
4-10
110907 07/10
Section 5 Contents
Engine, 17 HP/ 21 HP Briggs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Engine, 26 HP Briggs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Engine, Honda GXV 530 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Fuel System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
110907 07/10
5-1
Engine, 17 HP/ 21 HP Briggs
TOWARD
ENGINE
20
27
16
10
12
18
RED
1
22
11
RED
2
BLK
3
1
23
1
4
1
TO
BATTERY
14
12
13
10
ORG 1
15
12
PART OF
ENGINE
1
17
19
24
25
TO FUEL
TANK
3
5
6
PART OF
ENGINE
24
21
2
28
7
26
8
9
5-2
110907 07/10
Engine, 17 HP/ 21 HP Briggs
INDEX NO.
PART NO.
QTY
DESCRIPTION
1
601800
1
601850
1
ENGINE 21 HP BRIGGS
2
034272
4
NT .312-18 HX G5 ZNYC
3
768523
8
FW .343X.687X.051/.080H
4
029876
1
LW .312 INT-EXT TOOTH Z
5
050161
4
CS .312-18 X 1.750 HX G5
6
793760
1
PULLEY, ENGINE-HYDRO DRIVE
7
601801
1
CLUTCH WARNER I-5217-53
8
763417
1
FW .454X1.50X.250
9
601834
1
CS .437-20 X 3.50 HX G5
10
024927
3
NT .250-20 HX GR.5 ZNYC
11
044255
1
NT #10-32 HX ZN
ENGINE 17.5 HP BRIGGS
12
768515
5
FW .281X.625X.051/.080H
13
030817
1
STARTER SOLENOID
14
055939
2
CS .250-20X .750 HX G5
15
601818
1
OIL DRAIN - 3/8-18 NPTF
16
601840
1
BATTERY CABLE, POS.
17
104786
1
OIL DRAIN HOSE
18
601844
1
BRIGGS CONTACT COVER
19
601982
2
CN .250-20X .150 MAX THK
20
771428
1
BATTERY CBL BOOT-RED(FS)
21
712372
1
KEY 1/4 SQ X 0.66 LG
22
601062
1
BATTERY CABLE, POS.
23
601841
1
BATTERY CABLE, NEG.
24
000323
2
CLIP
25
015818
1
FUEL LINE 9"
26
015818
1
FUEL LINE 12"
27
602062
1
SC # 8 X 1.00 PHCR BO
28
791251
1
HARNESS, CLUTCH PIGTAIL
NOTES:
1. Part of mower wiring harness.
2. Pigtail supplied with clutch.
3. Engine oil capacity: Refer to engine owner’s manual. Tighten dipstick
before checking.
4. Torque to 45-48 ft-lbs. If fastener is loosened or removed, do not re-use.
Replace with new fastener. Use only hand tools to install this fastener.
ENGINE SPEED
110907 07/10
MODEL NO. ENDING IN:
HIGH IDLE
NO EXTENSION
3450±50 RPM
5-3
Engine, 26 HP Briggs
3
2
2
3
1
4
5
RED
1
TO BATTERY
POSITIVE
TERMINAL
8
1
8
3
2
3
3
2
9
10
7
1
3
BLK
6
TO BATTERY
NEGATIVE
TERMINAL
11
13
14
12
23
24
BLK
1
15
25
26
1
TOWARD
ENGINE
28
16
17
1.5"
24
19
29
27
16
1.75"
18
20
29 30
21
22
5-4
110907 07/10
Engine, 26 HP Briggs
INDEX NO.
PART NO.
QTY
DESCRIPTION
1
602388
1
BRIGGS 26 HP ENGINE
2
024927
5
NT .250-20 HX GR5 ZN
3
768515
7
FW .281 X .625 X .051/.080 HD
4
601062
1
POS BATTERY CABLE 17"
5
044255
1
NT #10-32 HX ZN
6
055939
2
CS .250-20 X .750 HX G5
7
030817
1
STARTER SOLENOID
8
601840
1
POS BATTERY CABLE 12"
SC # 8 X 1.00 PHCR BO
9
602062
1
10
602422
1
STATIC COVER ASSEMBLY
11
601818
1
OIL DRAIN 3/8-18 NPTF
12
104786
1
OIL DRAIN HOSE
13
785543
2
GASKET, MUFFLER
14
704478
4
CS .312-18X .75 SKTHD
15
602389
1
BRIGGS 26 MUFFLER
16
000331
3
WIRE TIE, SMALL/SHORT
17
712372
1
KEY 1/4 SQ X 0.66 LONG
18
793760
1
ENGINE PULLEY
19
791251
1
CLUTCH PIGTAIL HARNESS
20
601784
1
WARNER CLUTCH
21
763417
1
FW .454 X 1.50 X .250
22
601834
1
CS .437-20 X 3.250 HXG5P85
23
034272
1
NT .312-18 HX G5 ZN
24
768523
5
FW .343 X .687 X .051/.080 H
25
601841
1
NEG. BATTERY CABLE
26
029876
1
LW .312 INT-EXT TOOTH ZN
27
050161
1
CS .312-18 X 1.750 HX G5
28
792788
3
SC .375-16 X 1.00 HX FL STP
29
000323
2
30
015818
28”
HOSE CLAMP CLIP
FUEL LINE
NOTES:
1. Part of wiring harness (601676).
2. Contains a 25 amp fuse.
3. Supplied with engine.
4. Torque to 45-48 ft-lbs. If fastener is loosened or removed, do not re-use.
Replace with new fastener. Use only hand tools to install this fastener.
5. Torque to 30 ft-lbs.
6. Engine oil capacity: Refer to engine owner’s manual. Tighten dipstick
before checking.
ENGINE SPEED
110907 07/10
MODEL NO. ENDING IN:
HIGH IDLE
NO EXTENSION
3450±50 RPM
5-5
Engine, Honda GXV 530
PART OF
ENGINE
23 PART OF
ENGINE
1
YEL/BLK 2
3
5
4
BLK
PART OF
ENGINE
TO
8 BATTERY
RED
D
RE
1 4
1
1
TOERY
TT
B A B LK
6
10
11
9
PART OF
ENGINE
12
4
24
13
25
DETAIL
TO FUEL
TANK
27
15
14
7
16
26
17
28
15
18
19
20
TOWARD
ENGINE
21
22
3
1.50"
1.75"
5-6
110907 07/10
Engine, Honda GXV 530
ITEM NO.
PART NO.
QTY
DESCRIPTION
1
785394
1
ENGINE, HONDA 16HP
2
602098
1
OIL PRESSURE WIRE/WIRING HARNESS
3
034272
4
NT .312-18 HX G5 ZNYC
4
768523
4
FW .343X.687X.051/.080H
5
601841
1
BATTERY CABLE, NEG.
6
029876
1
LW .312 INT-EXT TOOTH Z
7
000331
7
WIRE TIE, SMALL/SHORT
8
602099
1
BATTERY CABLE, POS.
9
768515
2
FW .281X.625X.051/.080H
10
782664
1
NT M8-1.25 HX STAINLESS
11
056077
2
CS .250-20X1.000 HX G5
12
601982
2
CN .250-20X .150 MAX THK
13
050161
4
CS .312-18X1.750 HX G5
14
015818
1
FUEL LINE 28"
15
000323
2
CLIP
16
791608
1
OIL DRAIN - VALVE M16X1.5
17
104786
1
OIL DRAIN HOSE
18
793760
1
PULLEY, ENGINE-HYDRO DRIVE
19
712372
1
KEY 1/4 SQ X 0.66 LG
20
601801
1
CLUTCH WARNER I-5217-53
21
763417
1
FW .454X1.50X.250
22
601834
1
CS .437-20 X 3.50 HX G5
23
602211
1
MUFFLER, HONDA 16 AE
24
110888
1
ENGINE GUARD, SPORT
25
086660
2
NT .375-16 HXZY NL
26
767954
4
FW .406X .812 X.060 SAE
27
016428
2
CS .375-16X2.50 HX GR5
28
791251
1
HARNESS, CLUTCH PIGTAIL
NOTES:
1. Part of tractor wiring harness.
2. Engine oil capacity: Refer to engine owner’s manual. Tighten dipstick
before checking.
3. Torque to 45-48 ft-lbs. If fastener is loosened or removed, do not re-use.
Replace with new fastener. Use only hand tools to install this fastener.
ENGINE SPEED
110907 07/10
MODEL NO. ENDING IN:
HIGH IDLE
NO EXTENSION
3450±50 RPM
5-7
Fuel System
2
1
3
4
5
2
4
5
4
5
5-8
110907 07/10
Fuel System
ITEM NO.
PART NO.
QTY
DESCRIPTION
1
779306
1
3.5" FUEL CAP
2
110080
1
FENDER RH
3
110081
1
FENDER TANK LH
4
768523
8
FW .343X.687X.051/.080H
5
034280
6
CS .312-18X .750 HX G5
NOTES:
1. Torque to 7 ft-lbs.
2. Suction hose and grommet included with new fuel tank.
3. Service parts available for the fuel tank:
PART
NUMBER
785295
110907 07/10
DESCRIPTION
FLANGE GROMMET
5-9
PART
NUMBER
DESCRIPTION
601805
SUCTION HOSE ASSY 22.0
5-10
110907 07/10
Section 6 Contents
Instrument Panel, 17/21 Briggs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Instrument Panel, 26 Briggs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Instrument Panel, Honda . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
Electrical Schematic—Briggs (601676) . . . . . . . . . . . . . . . . . . . . . . 6-10
Electrical Schematic—Honda GXV 530 (602096) . . . . . . . . . . . . . . 6-11
110907 07/10
6-1
Instrument Panel, 17/21 Briggs
1
11
2
1
3
4
10
11
9
11
5
10
10
13
12
2
3
6
7
8
9
RIGHT SIDE
FENDER
1
6-2
110907 07/10
Instrument Panel, 17/21 Briggs
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
776476
1
2
785808
1
KEY ASSEMBLY (FS)
3
045898
1
IGN SWITCH INDAK 3H463
4
601053
2
RELAY
5
601098
4
CB 10-24 X .500 ZYNC
6
000331
5
WIRE TIE, SMALL/SHORT
7
601803
1
THROTTLE/CHOKE CABLE ASSY
8
704932
2
FW .219X .500X.048 ZNYC
NT #10-24 HX NL ZN
SWITCH, PTO 6201-321(FS)
9
059832
4
10
768515
3
FW .281X.625X.051/.080H
11
055947
3
CS .250-20X .500 HX G5
12
550224
1
INSTRUMENT PANEL
13
601811
1
DASH DECAL
NOTES:
1. Part of 601676 wiring harness.
2. Item 12 includes 601811 (Dash Decal).
110907 07/10
6-3
Instrument Panel, 26 Briggs
1
10
2
8
1
10
3
14
9
9
10
9
12
4
11
2
3
6
5
7
8
13
6-4
110907 07/10
Instrument Panel, 26 Briggs
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
776476
1
2
785808
1
KEY ASSEMBLY (FS)
3
045898
1
IGN SWITCH INDAK 3H463
4
601098
4
CB 10-24 X .500 ZYNC
5
000331
5
WIRE TIE, SMALL/SHORT
6
602555
1
40" THROTTLE/CHOKE CABLE
7
704932
2
FW .219X .500X.048 ZNYC
8
059832
4
NT #10-24 HX NL ZN
SWITCH, PTO 6201-321(FS)
9
768515
3
FW .281X.625X.051/.080H
10
055947
3
CS .250-20X .500 HX G5
11
550224
1
INSTRUMENT PANEL
12
601811
1
DASH DECAL
13
601676
1
WIRING HARNESS
14
601053
2
SEALED RELAY
NOTES:
1. Part of 601676 wiring harness.
2. Item 11 includes 601811 (Dash Decal).
110907 07/10
6-5
Instrument Panel, Honda
12
1
13
12
2
12
13
3
13
4
11
14
5
15
6
2
7
1
5
8
1
9
10
11
RIGHT SIDE
FENDER
1
ORG
6-6
YEL/BLK
110907 07/10
Instrument Panel, Honda
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
601097
1
CHOKE CABLE
2
776476
1
SWITCH, PTO 6201-321(FS)
3
712257
1
INDICATOR LIGHT, RED(FS)
4
785808
1
KEY ASSEMBLY (FS)
5
045898
1
IGN SWITCH INDAK 3H463
6
601053
2
RELAY
7
601098
4
CB 10-24 X .500 ZYNC
8
000331
5
WIRE TIE, SMALL/SHORT
THROTTLE CABLE
9
601096
1
10
704932
2
FW .219X .500X.048 ZNYC
11
059832
4
NT #10-24 HX NL ZN
12
055947
3
CS .250-20X .500 HX G5
13
768515
3
FW .281X.625X.051/.080H
14
602232
1
DASH DECAL INSTRUMENT
15
550225
1
INSTRUMENT PANEL SPORT
NOTES:
1. Part of 602096 wiring harness.
2. Item 15 includes 602232 (Dash Decal Instrument).
110907 07/10
6-7
Battery
1
2
3
POSITIVE
CABLE (RED)
4
7
6
5
5
5
4
5
6
2
1
NEGATIVE
CABLE (BLACK)
11
MOWER
FRAME
8
9
6-8
110907 07/10
Battery
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
601930
2
CS .250-20 X 6.50 HX G5
2
768515
2
FW .281 X .625 X .051/.080H
3
348417
1
BATTERY CLAMP STRAP
4
055939
2
CS .250-20 X .750 HX G5 ZN
5
029868
4
LW .250 INT-EXT TOOTH ZN
6
024927
2
NT .250-20 HX GR.5 ZNYC
7
771428
1
BATTERY CBL BOOT-RED
8
601982
2
CN .250-20X.150 MAX THK
GM 1.50 X 2.12 X 1.75
9
794644
1
10
000331
2
WIRE TIE, SMALL/SHORT
11
740696
1
BATTERY
NOTES:
1. When performing service on mower, disconnect battery ground cable
and do not reconnect to battery until engine is ready to be started. See
Owners Manual.
2. Battery is not installed in export models.
110907 07/10
6-9
Electrical Schematic—Briggs (601676)
6-10
110907 07/10
Electrical Schematic—Honda GXV 530 (602096)
110907 07/10
6-11
6-12
110907 07/10
Section 7 Contents
42" Deck Decals—Forward Swept . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
42" Deck Decals—Rear Swept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
48" Deck Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
54" Deck Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9
42" Deck Pulleys and Spindles—Forward Swept . . . . . . . . . . . . . . 7-11
Deck Pulleys and Spindles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13
48" Deck Pulleys and Spindles . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15
54" Deck Pulleys and Spindles . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17
42" Deck—Forward Swept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19
42" Deck—Forward Swept Belt Routing & Tensioning . . . . . . . . . . 7-21
42" Deck—Rear Swept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-23
42" Deck—Rear Swept Belt Routing & Tensioning . . . . . . . . . . . . . 7-25
48" Deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-27
48" Deck Belt Routing & Tensioning . . . . . . . . . . . . . . . . . . . . . . . . 7-29
54" Deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-31
54" Deck Belt Routing and Tensioning . . . . . . . . . . . . . . . . . . . . . . 7-33
DeckLift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-35
Deck Mounting Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-37
110907 07/10
7-1
42" Deck Decals—Forward Swept
2
1
2
9
8
3
4
5
6
7
7-2
110907 07/10
42" Deck Decals—Forward Swept
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
550011
1
DECK W/A, 42" SPORT
2
601069
4
CN .312-18X.200 MAX THK
3
601837
1
DECK DANGERS DECAL
4
601892
1
THROWN OBJECTS DECAL
5
794503
1
STEP TREAD
6
793521
1
42 DECK ID DECAL
7
602243
1
BELT ROUTING DECAL
8
601817
1
DISCHARGE DECAL
9
601816
1
DECK DANGERS DECAL
NOTES:
1. Item 1 (Deck Weldment) includes Items 2–9.
110907 07/10
7-3
42" Deck Decals—Rear Swept
2
1
2
3
4
4
5
7
8
6
7-4
110907 07/10
42" Deck Decals—Rear Swept
INDEX NO.
PART NO.
QTY
DESCRIPTION
1
550592
1
2
601069
4
CN .312-18 X .200 MAX THK
3
601624
1
DISCHARGE CHUTE DECAL
4
601837
2
DECK DANGERS DECAL
5
601892
1
THROWN OBJECTS DECAL
6
602243
1
BELT ROUTING DECAL
7
794503
1
STEP TREAD 3 X 6
8
793521
1
42" DECK ID DECAL
42" DECK
NOTES:
1. Item 1 includes items 2–8.
110907 07/10
7-5
48" Deck Decals
2
1
2
8
9
3
4
5
6
7
7-6
110907 07/10
48" Deck Decals
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
109754
1
48" DECK W/A
2
601069
2
CN .312-18X.200 MAX THK
3
601816
1
DECK DANGERS DECAL
4
601892
1
THROWN OBJECTS DECAL
5
794503
1
STEP TREAD
6
793976
1
48" DECK ID DECAL
7
781419CE
1
DECK BELT RTG DECAL
8
601817
1
DISCHARGE DECAL
9
601837
1
DECK DANGERS DECAL
NOTES:
1. Item 1 (Deck Weldment) includes Item 2–9.
110907 07/10
7-7
54" Deck Decals
4
3
1
5
2
4
8
INDEX NO.
PART NO.
QTY
1
550533
1
54" DECK
2
781419
1
BELT ROUTING DECAL
3
601837
2
DECK DANGERS DECAL
4
601069
4
CN .312-18 X .200 MAX THK
5
601624
1
DISCHARGE CHUTE DECAL
6
601892
1
THROWN OBJECTS DECAL
7
794503
1
STEP TREAD
8
799171
1
54" DECK ID DECAL
7
6
3
DESCRIPTION
NOTES:
1. Item 1 includes items 2 through 8.
7-8
110907 07/10
This page intentionally left blank.
110907 07/10
7-9
42" Deck Pulleys and Spindles—Forward Swept
1
2
3
8
4
7
6
5
9
1
2
10 2
3
11
4
12
3
13
14
15
25
24
1
20
18
22
19
23
18
17
21
15
16
7-10
110907 07/10
42" Deck Pulleys and Spindles—Forward Swept
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
794446
2
CS .625-11X1.500 HX G5
2
046821
2
FW .656X 2.00X.078 ZNYC
3
797449
3
FW .650X1.125X.18 ZNYCG5
4
784504
2
PULLEY, IDLER, 5.00"OD
5
109770
1
IDLER SLIDE W/A
6
781302
1
IDLER SPRING
7
259812
1
CHAIN DECK LIFT SPRING
8
784199
4
CS .312-18X1.250 FLT SH
9
601619
2
IDLER SLIDE UHMW RT & LT
10
705954
2
CS .500-13X1.25 HX G5 Z
11
798603
2
FW .515X1.65X.125 HD ZY
12
793778
2
DECK SPINDLE PULLEY
13
045765
2
FW 1.030X 1.500X.134 ZN
14
054502
8
NT .375-16 HX GRD 5 ZNY
15
767954
16
FW .406X .812 X.060 SAE
16
005116
8
CS .375-16X1.375 HX G5
17
781708
1
CS .500-13X4.250 HX G5
18
767962
2
FW .531X 1.063X.090 SAE
19
031997
1
ANTI-SCALP WHEEL
20
053199
1
NT .500-13 HX JAM ZNYC
21
601804
2
SPINDLE ASSEMBLY
22
768523
4
FW .343X.687X.051/.080H
23
058776
4
NT .312-18 HXZY NL
24
781567
1
NT .500-13 HX G8 ZY NL
25
788166
1
ANTI SCALP WHEEL ASSY
NOTES:
1. Item 25 includes Items 17–20.
2. Torque to 73 ft. lbs.
110907 07/10
7-11
Deck Pulleys and Spindles
1
2
3
4
7
6
8
5
9
1
10
1
11
2
12
3
4
13
14
3
20
21
2
25
23
24
23
22
15
17
19
14
18
16
7-12
110907 07/10
Deck Pulleys and Spindles
INDEX NO.
PART NO.
QTY
DESCRIPTION
1
794446
2
CS .625-11 X 1.500 HX G5 ZNYC
2
046821
2
FW .656 X 2.00 X .078 ZNYC
3
797449
3
FW .650 X 1.125 X .180 ZNYC G5
4
784504
2
IDLER PULLEY 5.00"
5
109770
1
IDLER SLIDE
6
036384
1
SPRING 1/4 COIL PL 1.23
7
259812
1
CHAIN DECK LIFT SPRING
8
784199
4
CS .312-18 X 1.250 FLT SH ZNYC
9
601619
2
IDLER SLIDE UHMW
10
705954
2
CS .500-13 X 1.250 HX G5 ZN
11
798603
2
FW .515 X 1.65 X .125 HD ZN
12
793778
2
DECK SPINDLE PULLEY
13
054502
8
NT .375-16 HX G5 ZN
14
767954
16
FW .406 X .812 X .060 SAE HRD ZN
15
601804
2
SPINDLE ASSEMBLY
16
005116
8
CS .375-16 X 1.375 HX G5 ZN
17
045765
2
FW 1.030 X 1.500 X .134 ZN
18
058776
4
NT .312-18 HX NL ZN
19
768523
4
FW .343 X .687 X .051/.080 HD ZN/YL
20
781567
1
NT .500-13 HX G8 ZN NY
21
788166
1
ANTI-SCALP WHEEL ASSEMBLY
22
781708
1
CS .500-13 X 4.250 HX G5
23
767962
2
FW .531 X 1.063 X .090 SAE
24
031997
1
ANTI-SCALP WHEEL
25
053199
1
NT .500-13 HX JAM ZNYC
NOTES:
1. Torque to 67-75 ft. lbs.
2. Item 21 includes items 22–25.
110907 07/10
7-13
48" Deck Pulleys and Spindles
1
2
3
8
4
6
7
5
9
1
2
3
10 2
3
11
4
12
13
23
21
14
22
21
20
24 1
19
17
18
16
7-14
14
15
110907 07/10
48" Deck Pulleys and Spindles
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
794446
3
CS .625-11X1.500 HX G5
2
046821
3
FW .656X 2.00X.078 ZNYC
3
797449
4
FW .650X1.125X.18 ZNYCG5
4
784504
3
PULLEY, IDLER, 5.00"OD
5
109770
1
IDLER SLIDE W/A
6
781302
1
IDLER SPRING
7
259812
1
CHAIN DECK LIFT SPRING
8
784199
4
CS .312-18X1.250 FLT SH
9
601619
2
IDLER SLIDE UHMW RT & LT
10
705954
3
CS .500-13X1.25 HX G5 Z
11
798603
3
FW .515X1.65X.125 HD ZY
12
792689
3
PULLEY 5.00"OD 80B102
13
054502
12
NT .375-16 HX GRD 5 ZNY
14
767954
24
FW .406X .812 X.060 SAE
15
005116
12
CS .375-16X1.375 HX G5
16
601804
3
SPINDLE ASSEMBLY
17
768523
4
FW .343X.687X.051/.080H
18
058776
4
NT .312-18 HXZY NL
19
781567
2
NT .500-13 HX G8 ZY NL
20
053199
2
NT .500-13 HX JAM ZNYC
21
767962
4
FW .531X 1.063X.090 SAE
22
031997
2
ANTI-SCALP WHEEL
23
781708
2
CS .500-13X4.250 HX G5
24
788166
2
ANTI SCALP WHEEL ASSY
NOTES:
1. Item 24 includes Items 20–23.
2. Torque to 73 ft. lbs.
110907 07/10
7-15
54" Deck Pulleys and Spindles
1
2
3
4
6
7
5
8
9
1
22
2
21
24 21
3
23
10 2
4
11
3
12
13
14
17
19
21
16
18
14
1 20
7-16
15
110907 07/10
54" Deck Pulleys and Spindles
INDEX NO.
PART NO.
QTY.
1
794446
3
CS .625-11 X 1.500 HX G5
DESCRIPTION
2
046821
3
FW .656 X 2.00 X .078 ZNYC
3
797449
4
FW .650 X 1.125 X .18 ZNYCG5
4
784504
3
PULLEY, IDLER, 5.00"OD
5
109770
1
IDLER SLIDE W/A
6
781302
1
IDLER SPRING
7
259812
1
CHAIN DECK LIFT SPRING
8
784199
4
CS .312-18 X 1.250 FLT SH
9
601619
2
IDLER SLIDE UHMW RT & LT
10
705954
3
CS .500-13 X 1.25 HX G5 Z
FW .515 X 1.65 X .125 HD ZY
11
798603
3
12
786889
3
PULLEY, DECK DRIVE 5.25
13
054502
12
NT .375-16 HX GRD 5 ZNY
14
767954
24
FW .406 X .812 X .060 SAE
15
005116
12
CS .375-16 X 1.375 HX G5
16
601804
3
SPINDLE ASSEMBLY
17
768523
4
FW .343 X .687 X .051/.080H
18
058776
4
NT .312-18 HXZY NL
19
781567
2
NT .500-13 HX G8 ZY NL
20
788166
2
ANTI SCALP WHEEL ASSY
21
767962
6
FW .531 X 1.063 X .090 SAE
22
781708
2
CS .500-13 X 4.250 HX G5
23
031997
2
ANTI-SCALP WHEEL
24
053199
2
NT .500-13 HX JAM ZNYC
NOTES:
1. Item 20 includes items 21–24.
2. Torque to 73 ft. lbs.
110907 07/10
7-17
42" Deck—Forward Swept
1
3
2
5
6
2
4
6
6
8
5
7
9
12
13
10
11
11
11
10
10
11
9
10
14
15
16 1
7-18
110907 07/10
42" Deck—Forward Swept
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
601806
1
2
601824
1
TORSION SPRING
3
601843
1
CHUTE PIN
4
111067
1
SPORT CHUTE BRACKET
5
767954
4
FW .406X .812 X.060 SAE
6
086660
5
NT .375-16 HXZY NL
7
110846
1
DISCHARGE CHUTE
8
600726
1
BELT A 114.3" EL
DISCHARGE CHUTE
9
025395
4
CB .375-16X 1.00 STD CD
10
034280
4
CS .312-18X .750 HX G5
11
768523
4
FW .343X.687X.051/.080H
12
110891
1
RIGHT HAND PULLEY COVER
13
110892
1
LEFT HAND PULLEY COVER
14
793794
2
BLADE 20.50"-L-F-CW
15
782474
2
CW .631 2.250X .187 PNT
16
781872
2
CS .625-11X1.25 HX G5 Z
NOTES:
1. Torque to 118 ft-lbs.
2. Do not torque, Item 1 (Discharge Chute) must pivot freely.
110907 07/10
7-19
42" Deck—Forward Swept Belt Routing & Tensioning
8.0"–9.0"
NOTES:
3. Spring length after tensioning new belt is measured from outside of hook
to outside of hook.
4. Route belt as shown.
7-20
110907 07/10
This page intentionally left blank.
110907 07/10
7-21
42" Deck—Rear Swept
1
2
3
4
5
6
9
5
2
5
6
7
10
11
8
12
13
8
13
12
14
15
1
7-22
16
110907 07/10
42" Deck—Rear Swept
INDEX NO.
PART NO.
QTY
DESCRIPTION
1
601806
1
2
601843
1
DISCHARGE CHUTE PIN
3
601824
1
TORSION SPRING
4
111067
1
CHUTE BRACKET
5
086660
5
NT .375-16 HXZY NL
6
767954
4
FW .406 X .812 X .060 SAE HRD ZN
7
112429
1
DISCHARGE CHUTE ADAPTOR
8
025395
4
CB .375-16 X 1.000 STD CD
DISCHARGE CHUTE
9
112187
1
PULLEY COVER RH
10
112188
1
PULLEY COVER LH
11
600726
1
BELT A-SECTION 114.3"
12
034280
4
CS .312-18 X .750 HX G5 ZN
13
768523
4
FW .343 X .687 X .051/.080 HD ZN/YL
14
793794
2
BLADE 20.50"-L-F-CW
15
782474
2
CW .631 X 2.250 X .187 PNT
16
781872
2
CS .625-11 X 1.250 HX G5 ZN
NOTES:
1. Torque to 118 ft. lbs.
2. Do not torque, Item 1 (Discharge Chute) must pivot freely.
110907 07/10
7-23
42" Deck—Rear Swept Belt Routing & Tensioning
4.5"–5.5"
NOTES:
1. Spring length after tensioning new belt. Measured from outside of hook
to outside of hook with deck set at 3¼" cut height.
2. Route belt as shown.
7-24
110907 07/10
This page intentionally left blank.
110907 07/10
7-25
48" Deck
1
3
2
6
2
7
9
10
6
11
4
5
8
6
5
9
10
13
12
13
14
15
16 1
10
19
18
17
7-26
110907 07/10
48" Deck
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
601806
1
2
601824
1
TORSION SPRING
3
601843
1
CHUTE PIN
4
111067
1
CHUTE BRACKET
5
767954
4
FW .406X .812 X.060 SAE
6
086660
5
NT .375-16 HXZY NL
7
771634
1
BELT, B 134.50" EL
8
110821
1
CHUTE ADAPTER PLATE 48"
DISCHARGE CHUTE
9
034280
2
CS .312-18X .750 HX G5
10
768523
4
FW .343X.687X.051/.080H
11
110840
1
RIGHT SIDE PULLEY COVER
12
110841
1
LEFT SIDE PULLEY COVER
13
025395
4
CB .375-16X 1.00 STD CD
14
601123
3
BLADE, 16.50"-L-F-CW
15
782474
3
CW .631 2.250X .187 PNT
16
781872
3
CS .625-11X1.25 HX G5 Z
17
111999
1
“A” BLOWOUT BAFFLE
18
016253
2
CB .312-18X .750 FUL ZN
19
058776
2
NT .312-18 HXZY NL
NOTES:
1. Torque to 118 ft-lbs.
2. Do not torque, Item 1 (Discharge Chute) must pivot freely.
110907 07/10
7-27
48" Deck Belt Routing & Tensioning
8.5"–9.5"
NOTES:
3. Spring length after tensioning new belt is measured from outside of hook
to outside of hook.
4. Route belt as shown.
7-28
110907 07/10
This page intentionally left blank.
110907 07/10
7-29
54" Deck
6
4
7
5
12
13
8
4
5
9
10
12
11
3
2
13
1
11
Discharge
Chute
14
15
19
16
5
17
18
2
1
Front
Wall
7-30
110907 07/10
54" Deck
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
777185
1
BELT, B 145.5" EL
2
112079
1
PULLEY COVER LS
3
112078
1
PULLEY COVER RS
4
034280
4
CS .312-18 X .750 HX G5
5
768523
6
FW .343 X .687 X .051/.080H
6
601806
1
DISCHARGE CHUTE
7
601824
1
SPRING, TORSION
8
601843
1
PIN, CHUTE
BRACKET, CHUTE
9
111067
1
10
110821
1
PLATE, CHUTE ADAPTER
11
025395
4
CB .375-16 X 1.00 STD CD
12
086660
5
NT .375-16 HXZY NL
13
767954
4
FW .406 X .812 X .060 SAE
14
601124
3
BLADE, 18.50"-L-F-CW
15
782474
3
CW .631 2.250 X .187 PNT
16
781872
3
CS .625-11 X 1.25 HX G5 Z
17
058776
2
NT .312-18 HXZY NL
18
111999
1
BAFFLE, "A" BLOWOUT
19
016253
2
CB .312-18 X .750 FUL ZN
NOTES:
1. Torque to 118 ft. lbs.
2. Install item 18 (111999 Baffle) to be flush with front wall of deck.
110907 07/10
7-31
54" Deck Belt Routing and Tensioning
8.25"—9.25"
NOTES:
1. Spring length after tensioning new belt. Measured from outside of hook
to outside of hook with deck set at 3¼" cut height.
7-32
110907 07/10
This page intentionally left blank.
110907 07/10
7-33
DeckLift
2
3
5
1
3
4
6
1
2
13
2
7
9
8
10
1
8
2
15
5
8
15
1
14
9
15
12
2
10
2
15
1
11
13
8
2
9
12
2
11
12
16
17
18
DECK PULLERS TO BE
MOUNTED TO INBOARD
SIDE ON TRACTOR,
OUTBOARD SIDE
ON DECK
7-34
110907 07/10
Deck Lift
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
054502
8
2
767954
16
FW .406X .812 X.060 SAEFW .406X .812 X.060 SAE
3
769257
2
FW .656X 1.250X.250 ZNY
4
110829
1
HANDLE, DECK HT LOCK
5
348862
2
STEERLEVER BUSHING
6
601963
1
PIN, DECK HEIGHT STOP
7
550216
1
DECK ADJUST PLATE LH
8
704643
12
NT .437-14 HX FLG ZN
CS .437-14X1.750 HX G5
NT .375-16 HX GRD 5 ZNY
9
055749
6
10
110929
2
DECK LIFT LINK, NON-SLOT
11
036244
6
CS .375-16X1.000 HX G5
12
601839
6
PIVOT SPACER BUSHING
13
110884
1
LIFT PEDAL LINK, SPORT
14
080655
2
CS .375-16X1.500 HX G5
15
015495
4
GREASE FITTING STRAIGHT
16
110879
2
PULLER STRAP, SPORT
17
110880
1
DECK LIFT LINK
18
601814
1
DECK HEIGHT DECAL
NOTES:
1. Apply grease to zerks.
2. Item 7 (Deck Adjustment Plate) includes Item 16 (Deck Height Decal).
3. See following page for deck mounting hardware.
110907 07/10
7-35
Deck Mounting Hardware
REAR SWEPT DECK
2
11
9
8
8
9
8
1
2
7-36
110907 07/10
Deck Mounting Hardware
FORWARD SWEPT DECK
2
11
9
8
8
9
8
1
110907 07/10
2
7-37
DECK BELT ADJUSTMENT
The spindle belt tension remains constant by means of a tension idler and spring. The spring tension should be such that the belt does not slip under normal operating load conditions, assuming
the belt is not excessively worn or damaged. As the belt stretches and wears in, adjusment may
become necessary. To increase belt tension, move the spring chain one (or more) link(s) at the
anchor point on the deck frame.
IMPORTANT: Do not over tension the spring to compensate for a badly worn belt or pulley.
SPRING CHAIN
ANCHOR POINT
SPRING CHAIN
IDLER
SPRING
FIG. 7
DECK LEVELING PROCEDURE
1. Check tire pressures (8 - 12 psi) to make certain they are properly inflated before
starting to level deck.
NOTE:
Stop engine. Make sure deck clutch switch is in the down (OFF) position. Remove ignition key. Place control levers in the brake position.
2. Drive mower onto hard flat surface.
3. Raise and lock deck into transport position.
4. Place 3" high deck support blocks (two stacked 2"x4" blocks can be used to create a 3"
high support) at the four corners of the deck as indicated in FIG. 8.
5. Remove the deck stop pin and lower the deck until it rests on the support blocks.
BLOCK
BLOCK
BLOCK
BLOCK
FIG. 8
7-38
110907 07/10
DECK LINK
DECK LINK
FIG. 9
6. Loosen the three bolts attaching the three deck links to the deck.
7. Push the lift pedal forward, place the deck stop pin in the indicator hole marked 3.25",
and release the pedal.
8. Pull the pedal rearward so that the crank lever is held firmly against the stop pin and
play in the pivot joint is removed; secure the pedal in this position (a bungee cord may
be used).
9. Tighten the three deck links to deck with flanged nuts clamping on either side of slot
with 48 ft-lbs of torque. Release the lift pedal and ensure that deck can be raised and
locked into transport position.
110907 07/10
7-39
7-40
110907 07/10
Section 8 Contents
Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
110907 07/10
8-1
Seat
1
3
2
5
6
3
7
4
4
8
15
9
5
4
10
11
4
12 1
13
14
8-2
110907 07/10
Seat
INDEX NO.
PART NO.
QTY.
DESCRIPTION
1
601807
1
SEAT-SPORT
2
550217
1
SEATPAN, SPORT
3
086660
2
NT .375-16 HXZY NL
4
767954
8
FW .406X .812 X.060 SAE
5
768523
6
FW .343X.687X.051/.080H
6
034280
4
CS .312-18X .750 HX G5
7
052860
2
CS .375-16X1.250 HX G5
8
793851
2
SPRING,COMP 1.25X4.00X.
CS .312-18X1.50 FLTHR G
9
756270
2
10
054502
2
NT .375-16 HX GRD 5 ZNY
11
601069
2
CN .312-18X.200 MAX THK
12
036244
2
CS .375-16X1.000 HX G5
13
110876
1
CATCH, SPORT SEAT PAN
14
070557
2
NT .312-18 HX UNT ZN
15
601815
1
DECAL, BATTERY
NOTES:
1. Do not torque, Item 2 (Seat Pan) must pivot freely.
2. Available service parts for Michigan seat: 793315 (Seat Switch).
3. Item 2 includes (601815 Battery Decal).
110907 07/10
8-3
8-4
110907 07/10
Numerical Index
Part
No.
Page
No.
Part
No.
Page
No.
Part
No.
Page
No.
068551
070557
080655
083279ca
086660
3-15
8-3
3-9, 4-3, 4-7, 7-35
2-4
2-5, 3-9, 3-15, 4-3,
4-5, 4-7, 4-9, 5-7,
7-19, 7-23, 7-27,
7-31, 8-3
5-3, 5-5, 5-7
7-7
7-11, 7-13, 7-15,
7-17
3-15
3-15
3-9, 4-3, 4-7
3-9, 4-3, 4-5, 4-7, 4-9
3-15
3-3
2-3
5-9
5-9
3-9, 4-3, 4-7
4-3, 4-7
3-9
7-27
7-35
7-27, 7-31
7-27, 7-31
7-19
8-3
7-35
5-7
7-19
7-19
7-35
7-19, 7-23, 7-27,
7-31
3-5
1-1
7-27, 7-31
7-23
7-23
7-23
2-5
7-31
7-11, 7-13, 7-15,
7-17
4-3
6-9
7-35
7-3
7-35
550217
550224
550225
550248
550249
550533
550592
600726
600899
601053
601062
601069
601096
601097
601098
601123
601124
601131
601390
601391
601398
601425
601426
601619
8-3
6-3, 6-5
6-7
2-3
2-3
7-8
7-5
1-1, 7-19, 7-23
2-3
6-3, 6-5, 6-7
5-3, 5-5
7-3, 7-5, 7-7, 7-8, 8-3
6-7
6-7
6-3, 6-5, 6-7
1-1, 7-27, 7-31
1-1
3-15
3-3
3-3
3-5
3-7
3-7
7-11, 7-13, 7-15,
7-17
7-5, 7-8
5-5, 6-5
5-5
5-3
5-3, 5-7
6-3
7-11, 7-13, 7-15,
7-17
5-9
7-19, 7-23, 7-27,
7-31
8-3
6-3, 6-5
2-3
2-3
7-35
8-3
7-3, 7-7
7-3, 7-7
5-3, 5-5
3-15
7-19, 7-23, 7-27,
7-31
5-3, 5-5, 5-7
7-3, 7-5, 7-7, 7-8
7-35
5-3, 5-5
Index
Part Numbers
000323
000331
005116
015495
015818
016253
016428
016972
017616
023655
024927
025395
028118
029868
029876
030817
031997
034272
034280
036244
036384
043067
044255
045765
045898
046821
048553
050161
052860
053199
054502
055749
055939
055947
056036
056077
058776
059832
063198
068478
110907 07/10
5-5, 5-7
5-5, 5-7, 6-3, 6-5,
6-7, 6-9
7-11, 7-13, 7-15,
7-17
7-35
5-5, 5-7
7-27, 7-31
2-5, 5-7
3-5
3-5
3-9, 3-15, 4-3, 4-5,
4-7, 4-9
5-3, 5-5, 6-9
7-19, 7-23, 7-27,
7-31
3-5
6-9
5-3, 5-5, 5-7
5-3, 5-5
4-3, 4-7, 7-11, 7-13,
7-15, 7-17
3-3, 5-3, 5-5, 5-7
5-9, 7-19, 7-23, 7-27,
7-31, 8-3
7-35, 8-3
3-5, 7-13
3-3
5-3, 5-5
7-11, 7-13
6-3, 6-5, 6-7
7-11, 7-13, 7-15,
7-17
3-3, 3-15
5-3, 5-5, 5-7
8-3
7-11, 7-13, 7-15,
7-17
3-3, 3-9, 4-3, 4-7,
7-11, 7-13, 7-15,
7-17, 7-35, 8-3
7-35
5-3, 5-5, 6-9
6-3, 6-5, 6-7
3-3
5-7
7-11, 7-13, 7-15,
7-17, 7-27, 7-31
6-3, 6-5, 6-7
3-15
1-1
104786
109754
109770
110000
110001
110007
110008
110009
110042
110063
110080
110081
110089
110116
110370
110821
110829
110840
110841
110846
110876
110880
110888
110891
110892
110929
111067
111079
111176
111999
112187
112188
112429
112849
190037
259812
339689
348417
348862
550011
550216
i-1
601624
601676
601784
601800
601801
601803
601804
601805
601806
601807
601811
601812
601813
601814
601815
601816
601817
601818
601822
601824
601834
601837
601839
601840
Part
No.
Page
No.
Part
No.
Page
No.
Part
No.
Page
No.
601841
601843
5-3, 5-5, 5-7
7-19, 7-23, 7-27,
7-31
5-3
1-1
1-1
1-1
1-1
1-1
5-3
1-1
1-1
7-3, 7-5, 7-7, 7-8
2-4
6-9
3-3
7-35
2-3
2-3
5-3, 5-7, 6-9
3-5
2-3
2-3
3-5
3-5
2-3
5-5
6-7
5-7
5-7
5-7
6-7
7-3, 7-5
5-5
5-5
5-5
6-5
1-1
1-1
1-1
1-1
5-5
7-35
6-3, 6-5, 6-7
3-9, 4-3, 4-7
7-11, 7-13, 7-15,
7-17
3-3
6-7
5-3, 5-5, 5-7
725796
727172
740696
756270
763417
765339
767954
3-15
2-3
6-9
8-3
5-3, 5-5, 5-7
3-15
2-5, 3-3, 3-9, 3-15,
4-3, 4-7, 5-7, 7-11,
7-13, 7-15, 7-17,
7-19, 7-23, 7-27,
7-31, 7-35, 8-3
4-3, 4-7, 7-11, 7-13,
7-15, 7-17
3-15, 5-3, 5-5, 5-7,
6-3, 6-5, 6-7, 6-9
3-3, 3-9, 3-15, 4-3,
4-7, 5-3, 5-5, 5-7,
5-9, 7-11, 7-13, 7-15,
7-17, 7-19, 7-23,
7-27, 7-31, 8-3
1-1
7-35
3-9, 4-3, 4-7
5-3, 6-9
1-1, 7-27
6-3, 6-5, 6-7
1-1, 7-31
5-9
3-15
3-9
7-11, 7-15, 7-17
7-8
7-7
3-5, 7-11, 7-13, 7-15,
7-17
4-3, 4-7, 7-11, 7-13,
7-15, 7-17
7-19, 7-23, 7-27,
7-31
7-19, 7-23, 7-27,
7-31
2-3
5-7
7-11, 7-13, 7-15,
7-17
7-11, 7-13, 7-15,
7-17
3-5
2-3
2-3
785295
785394
785543
785626
785808
786889
787226
787234
787242
788166
5-9
5-7
5-5
1-1
6-3, 6-5, 6-7
7-17
1-1
1-1
1-1
7-11, 7-13, 7-15,
7-17
3-3
3-3
5-3, 5-5, 5-7
5-7
7-15
5-5
3-3
8-3
7-3, 7-5
5-3, 5-5, 5-7
7-11, 7-13
1-1, 7-19, 7-23
8-3
7-7
7-11, 7-13, 7-15,
7-17
7-3, 7-5, 7-7, 7-8
6-9
3-3
3-9, 4-3, 4-7
7-11, 7-13, 7-15,
7-17
3-5
3-3
3-3
7-11, 7-13, 7-15,
7-17
7-8
2-3
1-1
1-1
1-1
1-1
1-1
1-1
1-1
1-1
1-1
601844
601845
601846
601847
601848
601849
601850
601865
601866
601892
601908
601930
601941
601963
601967
601981
601982
601983
601986
601987
602025
602026
602041
602062
602096
602098
602099
602211
602232
602243
602388
602389
602422
602555
602570
602571
602572
602607
704478
704643
704932
705178
705954
710087
712257
712372
767962
768515
768523
769133
769257
770867
771428
771634
776476
777185
779306
781211
781260
781302
781419
781419CE
781567
781708
781872
782474
782573
782664
784199
784504
784827
785139
785220
i-2
788232
788877
791251
791608
792689
792788
793174
793315
793521
793760
793778
793794
793851
793976
794446
794503
794644
795047
796615
797449
797514
798363
798371
798603
799171
808485
929125
929125CA
929133
929133CA
929463
929471
929596
929851
929869
110907 07/10