CAR CARRIER - Miller Industries

OWNER'S MANUAL
CAR CARRIER
INSTALLATION, OPERATION, MAINTENANCE & PARTS
NOTE: MANUAL including SPECIFICATIONS, subject to change without notice
All ratings specified are based on structural factors only,
not vehicle capacities or capabilities.
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive
Ooltewah, Tennessee 37363
Phone (423) 238-7227 ï FAX (423) 238-7237
FORM NO. 9121921
01 / 03
PRICE $25.00
LIMITED WARRANTY
MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as MILLER, warrants to
the original purchaser that each new MILLER wrecker or other MILLER products will be free from
defects in material and workmanship for a period of twelve (12) months from date placed in service,
but in no event shall such warranty period exceed twenty-four (24) months from date of manufacture
by MILLER. The purchaser must promptly notify MILLER in writing of any failure in material or
workmanship. In no event shall MILLER accept such notification later than twenty-four (24) months
from date of delivery or twelve (12) months from date placed in service, whichever is earlier.
MILLER's obligation under this warranty, statutory or otherwise, is limited to the repair or replacement
at the MILLER factory, or at a point designated by MILLER, of such part or parts as shall appear upon
inspection by MILLER to be defective in material or workmanship. New or remanufactured parts will be
used for any replacement at MILLER's option. This warranty is not transferable. This warranty does
not obligate MILLER to bear the cost of labor or transportation charges in connection with the repair or
replacement of any parts found to be defective, nor shall it apply to a product upon which repairs or
alterations have been made unless authorized by MILLER.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, MILLER MAKES NO OTHER
WARRANTY, EXPRESS OR IMPLIED, AND HEREBY DISCLAIMS ALL OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. MILLER shall in no event be liable for claimed downtime,
claimed loss of profits or goodwill, or any other special, incidental, indirect, or consequential damages
concerning or relating to any product or parts, whether based on negligence, strict liability, breach of
contract, breach of warranty, misrepresentation or any other legal theory, regardless of whether the
loss resulted from any general or particular requirement which MILLER knew or had reason to know
about at the time of sale.
MILLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, AS TO THE FINISHED PRODUCTS
MANUFACTURED OR SUPPLIED BY ANOTHER MANUFACTURER AND SUPPLIED BY MILLER
TO PURCHASER, including, but not limited to, any vehicle to which a MILLER product may be affixed
or any accessories or wire rope, and MILLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AS TO SUCH EQUIPMENT
OR PRODUCTS. This language shall in no way affect or diminish the rights of the purchaser to rely
on such warranties as are extended by such manufacturers or suppliers. MILLER shall, to the extent
permitted under applicable law, pass on to the purchaser such manufacturer's or seller's warranty.
MILLER, whose policy is one of continuous improvement, reserves the right to improve its products
through changes in design or materials as it may deem desirable without being obligated to incorporate
such changes in products previously sold. This warranty is not intended to cover or include the
following items, which are set forth by way of example and not limitation:
A. Normal deterioration of trim, paint, lettering, and appearance items due to wear or exposure to
weather, road conditions, road treatments, etc.
B. Any damage or defect due to accident, misuse, abuse, improper or unauthorized repairs, failure
to provide reasonable and necessary maintenance, or uses for which the equipment was not
designed or intended.
C. Alterations or modifications that affect performance, operation or reliability.
D. Normal maintenance parts including, but not limited to, wear pads, bushings, wire rope, mud
flaps, fenderettes, light bulbs, hydraulic oil, filters, and tow sling belts.
IT IS EXPRESSLY UNDERSTOOD THAT MILLER MAKES NO IMPLIED WARRANTY THAT MILLER
PRODUCTS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR MOVING PEOPLE OR FOR ANY
OTHER IMPROPER USE.
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive
Ooltewah, Tennessee 37363
Telephone (423) 238-4171
SERIAL NUMBER
Section VI - PARTS
This Section is provided by the manufacturer for the
purpose of ordering any component part of the CAR CARRIER
that may be required when part replacement is necessary.
Be certain to use only original equipment replacement
parts for warranty purposes as well as for keeping your
CAR CARRIER in its original state and optimum operating
capacities.
When ordering replacement or spare parts be sure to
provide the following information to the manufacturer's
Parts Department.
1.
2.
3.
4.
5.
6.
7.
Manual Number & Date of Publication
Manual Page Number
Page Title
Reference Number of Part Desired
Part Number
Part Description
Quantity of Part Desired
Providing this information will help ensure that the
correct parts will be delivered to you in an expedient
manner without delay. Should additional information be
required for repair or replacement of certain components,
contact your Wrecker Manufacturer Authorized
Representative.
The Manufacturer reserves the right, without notice or
obligation, to improve or modify their products, which
may change the specifications, models and feature
availability.
VI-1
Section VI - PARTS (cont'd)
ALUMINUM BED ASSEMBLY
VI-2
Section VI - PARTS (cont'd)
ALUMINUM BED ASSEMBLY
ID
NO
PART
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
0300132
0300134
0300250
0301669
0301740
0301861
0302027
0302180
0400044
0400077
0400088
0400181
0400237
0400408
0400492
0701172
0702517
0708913
0709868
0709869
0709870
0801482
0802660
0802661
0802662
0805033
0805096
0805000-32
0805000-34
0805000-36
0805020-45
0805020-48
0805020-54
LT0118
LT0119
29
30
DESCRIPTION
WIRE TIE
HOSE CLAMP
WINCH ASSEMBLY
CABLE ASSEMBLY, WINCH
GROMMET, LIGHT ASSEMBLY MOUNTING
PIN, LYNCH
BEARING PAD
BEARING PAD, SPECIFY BODY LENGTH
SCREW, 10 X 1/2" RD HD DRIVE
SCREW, 1/4" X 1" SELF DRILLING
SCREW, 1/4"-20 X 5/8" FL HD PH
SCREW, 1/2"-13 X 1-1/2" HEX HD CAP
SCREW, 1/2"-13 X 4" HEX HD CAP
NUT, 1/2"-13 NYLOK HEX
WASHER, 1/2" FL
SPACER WINCH BRACKET
BEARING PAD STOP BAR
ANTI TILT PLATE
COVER PLATE (BOTTOM)
CAP, END
CAB PROTECTOR REINFORCEMENT PLATE
WINCH MOUNTING BRACKET
SIDE RAIL, FRONT REMOVABLE 19'
CENTER REMOVABLE SIDE RAIL
REAR REMOVABLE SIDE RAIL
CAR CARRIER 19' ALUMINUM
TRAY, HOSE (SPECIFY BODY LENGTH)
CAB PROTECTOR - 32"
CAB PROTECTOR - 34"
CAB PROTECTOR - 36"
CAB PROTECTOR - 45"
CAB PROTECTOR - 48"
CAB PROTECTOR - 54"
LIGHT ASSEMBLY, AMBER
LIGHT ASSEMBLY, RED (NOT SHOWN)
VI-3
QTY
8
2
1
1
2
4
2
2
6
15
8
6
4
10
16
2
4
1
1
2
2
1
2
2
2
1
1
1
2
2
Section VI - PARTS (cont'd)
STEEL BED ASSEMBLY
VI-4
Section VI - PARTS (cont'd)
STEEL BED ASSEMBLY
ID
NO
PART
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
0805047
0805048
0300250
0400181
0801482
0701172
0805000-32
0805000-34
0805000-36
0805000-45
0805000-48
0805000-54
0400408
0400088
0306033
0400177
0306032
0400089
0300134
0400367
0705332
0400077
0301887
0300132
0805096
0400211
0708913
0802660
24
25
26
27
0802661
0802662
0301669
0805039
28
0301861
DESCRIPTION
CAR CARRIER 19' STEEL
CAR CARRIER 21' STEEL
WINCH ASSEMBLY
SCREW, 1/2"-13 X 1-1/2" HEX HD CAP
WINCH MOUNTING BRACKET
SPACER, WINCH BRACKET
CAB PROTECTOR - 32"
CAB PROTECTOR - 34"
CAB PROTECTOR - 36"
CAB PROTECTOR - 45"
CAB PROTECTOR - 48"
CAB PROTECTOR - 54"
NUT, 1/2"-13 NYLOK
SCREW, 1/4"-20 X 5/8" FL HD PH
BEARING PAD
SCREW, 1/2"-13 X 1-1/4" HEX HD CAP
BEARING PAD
SCREW, 1/4"-20 X 1" FL HD PH
HOSE CLAMP
NUT, 1/4"-20 NYLOK HEX HD
COVER PLATE, BOTTOM
SCREW, 1/4" X 1" SELF-DRILLING
LIGHT ASSEMBLY, AMBER
WIRE TIE
TRAY, HOSE (SPECIFY BODY LENGTH)
SCREW, 1/2"-13 X 1-3/4" HEX HD CAP
ANTI TILT PLATE
FRONT REMOVABLE SIDE RAIL
(19'CARRIER)
CENTER REMOVABLE SIDE RAIL
REAR REMOVABLE SIDE RAIL
CABLE ASSEMBLY, WINCH
FRONT REMOVABLE SIDE RAIL
(21' CARRIER)
PIN, LYNCH
VI-5
QTY
1
1
1
4
1
2
1
10
8
8
2
2
38
2
38
1
13
2
8
1
4
1
2
2
2
1
2
4
Section VI - PARTS (cont'd)
TILT FRAME ASSEMBLY
VI-6
Section VI - PARTS (cont'd)
TILT FRAME ASSEMBLY
ID
NO
PART
NO
1
2
3
4
5
0805093
0300113
0805019
0805035
0802668
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
0704792
0301800
0302474
0303123
0303124
0304147
0702434
0709867
0709878
0400211
0301932
0304642
0301671
0300867
0300273
0302987
0300686
0400564
0302988
0802666
0306001
DESCRIPTION
RESERVOIR ASSEMBLY
GREASE FITTING
SUB-FRAME, INDEPENDENT WHEEL LIFT
SUB-FRAME, INDEPENDENT TOW BAR
OIL TANK MTG BRACKET
(SPECIFY FRAME WIDTH)
PIN, PIVOT
JUNCTION BOX
PIN, LYNCH
LIGHT, STOP & TURN, RED
LIGHT, BACKUP, CLEAR
WORK LIGHT
SHAFT, LIFT CYLINDER
PIN, SAFETY
WEAR PAD
SCREW, 1/2"-13 X 1-3/4" HEX HD CAP
SAFETY CHAIN w/HOOKS 12'
CHECK VALVE, PIVOT
SOCKET, TOW LIGHT
ILLUMINATOR, CONTROL PANEL
ILLUMINATOR, LICENSE PLATE
MARKER LIGHT, SEALED RED
THROTTLE ASSEMBLY (25 FT.)
PIN, ROLL
TOOL BOX
EXTENSION STAND (WHEN NEEDED)
MUD FLAP
VI-7
QTY
1
4
1
1
2
1
1
1
4
2
2
4
1
2
20
2
10
1
2
1
2
1
1
1
2
2
Section VI - PARTS (cont'd)
TILT FRAME ASSEMBLY (cont'd)
VI-8
Section VI - PARTS (cont'd)
TILT FRAME ASSEMBLY (cont'd)
ID
NO
PART
NO
DESCRIPTION
QTY
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
0705092
0704793
0400122
0400121
0400392
0703960
0300132
0301601
0400150
0303061
0802667
0301397
0300134
0500805
0500806
0802664
0802665
0700584
0802663
0400408
0801558
0801557
0300442
0801559
0720030
0710777
0720031
BAR, MUD FLAP
BRACKET, MUD FLAP MOUNTING
SCREW, 3/8"-16 X 1-1/4" HEX HD CAP
SCREW, 3/8"-16 X 3/4" HEX HD CAP
NUT, 3/8"-16 NYLOK
PIN, EXTEND CYLINDER
CABLE TIE
CLAMP, INSULATED WIRE
SCREW, 3/8"-16 X 2-1/2" HEX HD CAP
BACK-UP ALARM
TOOL BOX MOUNTING BRACKET
GREASE FITTING, 90°
CLAMP, INSULATED WIRE
DECAL, CONTROL STATION (L.H.)
DECAL, CONTROL STATION (R.H.)
TAIL LAMP HOUSING, LEFT
TAIL LAMP HOUSING, RIGHT
CHAIN, 12" SASH
L-ARM STORAGE TUBE BRACKET
NUT, 1/2"-13 NYLOK
CONTROL BOX, RIGHT SIDE
CONTROL BOX, LEFT SIDE
LIGHTS
CONTROL CHANNEL ASSEMBLY
TAIL LAMP MOUNTING PLATE, LT SIDE
HOSE TRAY
TAIL LAMP MOUNTING PLATE, RT SIDE
2
2
9
8
20
1
18
8
1
1
2
3
4
1
1
1
1
1
2
20
1
1
3
?
1
1
1
VI-9
Section VI - PARTS (cont'd)
WHEEL LIFT & CROSSBEAM ASSEMBLY
WITH WHEEL RETAINERS
VI-10
Section VI - PARTS (cont'd)
WHEEL LIFT & CROSSBEAM ASSEMBLY
WITH WHEEL RETAINERS
ID
NO
PART
NO
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
0300113
0705238
0400392
0801012
0301850
0302183
0400044
0400129
0400139
0400392
0702131
0703277
0703345
0801556
0801568
0400141
0801009
0400150
8700180
8700190
8609001
9025068
0301932
8600404
8601900
GREASE FITTING
PIN, PIVOT
NUT, 3/8"-16 NYLOK HEX
SHAFT, LIFT CYLINDER
BEARING PAD, NYLATRON
BEARING PAD, 3/8"
SCREW, #10 X 1/2" DRIVE
SCREW, 3/8"-16 X 3/4" CUP PT ALN HD
SCREW, 3/8"-16 X 1-1/2" HEX HD SKT
NUT, 3/8"-16 NYLOK
SHAFT, INNER TUBE CYLINDER
SLIDER, PAD
SHAFT, EXTEND CYLINDER
OUTER BOOM
INNER BOOM
SCREW, 3/8"-16 X 7/8" HEX HD CAP
SHAFT, PIN ASSEMBLY, UPPER BOOM
SCREW, 3/8"-16 X 2-1/2" HEX HD CAP
WHEEL RETAINER, RIGHT
WHEEL RETAINER, LEFT
CROSSBEAM PIVOT PIN
REFLECTOR
SAFETY CHAIN, 10'
WASHER, 11/16" ID X 2" OD
SLIDE LOCK HANDLE KNOB ASSEMBLY
2
1
3
1
1
1
4
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
VI-11
Section VI - PARTS (cont'd)
WHEEL LIFT & CROSSBEAM ASSEMBLY
WITH WHEEL RETAINERS (cont'd)
VI-12
Section VI - PARTS (cont'd)
WHEEL LIFT & CROSSBEAM ASSEMBLY
WITH WHEEL RETAINERS (cont'd)
ID
NO
PART
NO
DESCRIPTION
QTY
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
880411500
8700109
880360500
880417000
880410000
8701600
8701500
9012944
9043950
9043956
9045255
9045259
8600406
9047057
9052013
9012501
9030214
9046310
8602001
8601608
890440003
9033198
0400139
0400392
07120060
STOP PIN ASSEMBLY
LOCK PIN, SCOOP
STINGER, CROSSBEAM
WHEEL GRID, RIGHT
WHEEL GRID, LEFT
SCOOP BRACKET, LEFT
SCOOP BRACKET, RIGHT
PIPE PLUG
SCREW, 5/8" NC X 1-1/2" HEX HD CAP
SCREW, 3/8" NC X 3/4" BTN HD ALN
WASHER, 3/8" FL
WASHER, 5/8" FL
WASHER, 1" X 3/8" FL
DIE SPRING
BALL BEARING, 1"
GREASE NIPPLE
"O" RING
ROLL PIN, 3/16" X 1-1/8"
LOCK PIN WITH CHAIN
SLIDE LOCK SOCKET
LOCKING PIN
SAFETY CHAIN DECAL
SET SCREW, 3/8"-16 X 1-1/2" HEX SKT
LOCKNUT, 3/8"-16 NYLOK HEX
PAD HOLDER
2
2
1
1
1
1
1
1
2
1
1
2
1
1
1
3
2
2
4
2
2
2
?
?
?
VI-13
Section VI - PARTS (cont'd)
HYDRAULICS
VI-14
Section VI - PARTS (cont'd)
HYDRAULICS
ID
NO
PART
NO
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
0300142
0300208
0301403
0301424
0301478
0301524
0301640
0301658
0301660
0301694
0301769
0302867
0301878
0301970
0301663
0301665
0705296
0300055
0300056
0300071
0300136
REF.
0300692
0300865
0301659
0300165
0704802
0300044
ELBOW, 6MJ-4MP90
TEE, 6MJ-6MP90
HOSE ASSEMBLY, 80-1/2"
CONNECTOR, 6MJ-4MP
HOSE ASSEMBLY, 54"
HOSE ASSEMBLY, 14"
VALVE, BED TILT CYLINDER LOCK
HOSE ASSEMBLY, 128"
HOSE ASSEMBLY, 21"
TEE, 6MJ-6MJ-4MP
HOSE ASSEMBLY, 52"
CYLINDER, BED LIFT
HOSE ASSEMBLY, 137"
CYLINDER, BED EXTEND
HOSE ASSEMBLY, 204" (WINCH MOTOR)
ELBOW, 6MJ-8MP90
SKUFF JACKET
HOSE BARB, 3/4" HOSE X 3/4" MP
HOSE BARB, 1" HOSE X 1" MP
CLAMP, 1" HOSE
FILTER ASSEMBLY
PTO CONNECTOR
ELBOW, 1" X 90° STREET
CONNECTOR, 8MJ-8MJ
HOSE ASSEMBLY, 150" (VALVE TO PUMP)
HOSE ASSEMBLY, 91" HI-PRESSURE
HOSE, 192" RETURN
CONNECTOR, 6MJ-8MB
6
2
2
5
2
2
1
1
2
1
1
2
2
1
2
2
1
3
1
4
1
1
1
1
1
1
1
10
VI-15
Section VI - PARTS (cont'd)
HYDRAULICS (cont'd)
VI-16
Section VI - PARTS (cont'd)
HYDRAULICS (cont'd)
ID
NO
PART
NO
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
0300065
0300789
0302179
0300347
0805093
0709871
0301522
0302178
0300133
0300209
0301473
0301484
0301731
0301848
0301868
0301900
0400064
0400366
0400451
0400452
0703001
0300090
0400196
0302170
0302160
0302037
0303485
DESCRIPTION
SWIVEL, 12MB-12FPX
CONNECTOR, 5/8" X 1/2" JIC STR
VALVE, 5 SPOOL
PLUG, 1/2" SQ HD BLK
RESERVOIR ASSEMBLY
FILLER CAP
CONNECTOR, 6MJ-6MB
CYLINDER, WHEEL LIFT EXTEND
CLAMP, CHECK VALVE
ELBOW, 6MJ-6MP90
HOSE ASSEMBLY, 18"
CYLINDER
VALVE, WHEEL LIFT HOLDING
ELBOW, 6MJ-6MP4S
TEE, 4FP-4MP
HOSE ASSEMBLY, 18"
SCREW, 1/4"-20 X 2-1/4" SL RD HD
NUT, 1/4"-20 HEX
WASHER, 1/4" FL
LOCKWASHER, 1/4" HELICAL
BRACKET, VALVE MNTG
MOTOR, WINCH
SCREW, 1/2"-13 X 1-1/4" SKT HD CAP
SWIVEL, 16C2-16FJX90
ELBOW, 6MJ-4MP90L
HOSE, 1" DIA. SUCTION
PTO
PUMP, HIGH PRESSURE HYDRAULIC
VI-17
QTY
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
2
2
2
1
1
2
1
1
1
1
1
Section VI - PARTS (cont'd)
CONTROL & CROSSROD ASSEMBLY
VI-18
Section VI - PARTS (cont'd)
CONTROL & CROSSROD ASSEMBLY
ID
NO
PART
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
0302179
0301638
0800798
0800797
0800795
0800796
0301720
0300341
0300834
0400393
0400541
0705242
0400532
0400465
0400121
0400482
0400392
0400243
0800800
0800799
0801566
0400543
0400140
0801274
0306006
DESCRIPTION
CONTROL VALVE, 5-SPOOL
BRACKET, CONTROL HANDLE
CONTROL HANDLE, OUTER REAR
CONTROL HANDLE, INNER REAR
CONTROL HANDLE, OUTER FWD
CONTROL HANDLE, INNER FWD
KNOB, BALL
KNOB
KNOB, "IN-OUT" CABLE
NUT, 3/8"-16 JAM
COTTER PIN, 1/16" X 3/4"
PIN, CONTROL HANDLE PIVOT
CLEVIS PIN, 5/16" X 1"
WASHER, 5/16"
SCREW, 3/8"-16 X 3/4" HEX HD CAP
LOCKWASHER, 3/8" HELICAL
NUT, 3/8"-16 NYLOK
NUT, 3/8"-16 TINNERMAN "J"
CONTROL ROD LINK
VALVE SHIFTER
CONTROL HANDLE, CENTER
COTTER PIN, 1/8" X 3/4"
SCREW, 3/8"-16 X 4" HEX HD CAP
CONTROL ROD LINK, ANTI TILT
SPRING, ANTI-RATTLE
VI-19
QTY
1
10
2
2
2
2
2
6
2
15
4
2
10
10
10
5
8
5
5
4
2
10
3
1
10
Section VI - PARTS (cont'd)
HYDRAULIC WINCH
VI-20
Section VI - PARTS (cont'd)
HYDRAULIC WINCH
ID
NO
PART
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
0300261
0300448
0300449
0300450
0300451
0300452
0300398
0300399
0300453
0300454
0300455
0300456
0300457
0300458
0300381
0300459
0300460
0300461
0300462
0300463
0300464
0300465
0300466
0300447
0300467
0300468
0300695
0300694
0300471
---0300472
0300473
0300474
0300475
0300476
0300477
0300569
0300290
DESCRIPTION
LEVER
KEY
SCREW
KEY
SHAFT
CLUTCH HOUSING
YOKE
SCREW
BUSHING
SCREW
SPRING
BALL
CLUTCH
SPACER
DRUM
PLUG
HOUSING
PLUG
REDUCER
DRAG BRAKE
SPRING
SCREW
CAP
GASKET
BEARING
WORM
SCREW
CAP ADAPTER
SEAL
KEY
SHAFT
KEY
HUB
GEAR
WASHER
SCREW
GASKET
COVER
SCREW
COUPLING
VI-21
QTY
1
1
1
1
1
1
1
1
5
1
1
1
1
1
1
2
1
1
1
1
1
16
1
2
2
1
1
1
1
2
1
2
1
1
6
6
1
1
4
1
Section VI - PARTS (cont'd)
CYLINDERS
ID
NO
PART
NO
1
2
0301970
0304219
ID
NO
PART
NO
1
2
0302867
0304219
DESCRIPTION
BED EXTEND CYLINDER (COMPLETE)
SEAL KIT
DESCRIPTION
BED TILT CYLINDER (COMPLETE)
SEAL KIT
VI-22
QTY
1
--
QTY
2
--
Section VI - PARTS (cont'd)
CYLINDERS
ID
NO
PART
NO
DESCRIPTION
QTY
1
2
0302178
0304086
WHEEL LIFT EXTEND CYLINDER, COMPLETE
SEAL KIT, EXTEND CYLINDER
1
1
ID
NO
PART
NO
DESCRIPTION
QTY
1
2
0301484
0304181
WHEEL LIFT LIFT CYLINDER, COMPLETE
SEAL KIT, LIFT CYLINDER
VI-23
1
1
Section VI - PARTS (cont'd)
OPTIONAL EQUIPMENT
CABLE ROLLER ASSEMBLY
ID
NO
PART
NO
1
2
3
4
0900892
0805037
0400177
0400408
DESCRIPTION
CABLE ROLLER ASSEMBLY
CABLE ROLLER GUIDE WELDMENT
SCREW, 1/2"-13 X 1-1/4" HEX HD CAP
NUT, 1/2"-13 NYLOK HEX
VI-24
QTY
-1
2
2
Section VI - PARTS (cont'd)
OPTIONAL EQUIPMENT
WINCH CLUTCH CONTROL
ID
NO
PART
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
0300845
0301532
0301588
0400116
0400126
0400150
0400392
0400393
0400492
0400537
0400546
0400560
0702408
0800780
0805060
0301397
DESCRIPTION
SPRING, COMPRESSION
"T" HANDLE
ADJUSTABLE YOKE
SCREW, 5/16"-18 X 1/2" SQ HD SET
SCREW, 3/8"-16 X 1" HEX HD CAP
SCREW, 3/8"-16 X 2-1/2" HEX HD CAP
NUT, 3/8"-16 NYLOK HEX
NUT, 3/8"-16 JAM HEX
WASHER, 1/2" FL
CLEVIS PIN, 1/2" X 1-1/2"
COTTER PIN, 1/8" X 1-1/4"
ROLL PIN, 5/32" X 1"
MOUNTING CHANNEL
CONTROL ROD, SINGLE WINCH
WELDMENT, BELL CRANK
GREASE FITTING 90°
VI-25
QTY
1
1
1
1
1
1
2
1
4
1
1
2
1
1
1
1
Section VI - PARTS (cont'd)
OPTIONAL EQUIPMENT
LIGHTING ACCESSORIES
ID
NO
PART
NO
1
2
3
4
5
6
7
8
0301359
0800539
0709872
0400392
0300095
0400043
0400356
0400520
DESCRIPTION
WRECKER SPECIAL LIGHT
"T" BOLT ADAPTER
RUBBER CUSHION
NUT, 3/8"-16 NYLOK HEX
SPOTLIGHT
SCREW, #10-24 X 1" PH HD MCHN
NUT, #10-24 NYLOK
LOCKWASHER, #10
VI-26
QTY
1
2
2
2
2
8
8
8
Section VI - PARTS (cont'd)
OPTIONAL EQUIPMENT
INDEPENDENT TOW BAR ASSEMBLY
ID
NO
PART
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
-0301381
0805030
0805150
0702434
0702418
0302368
0500241
0301723
0800898
0300113
0800784
0400436
0301642
0800777
0301798
DESCRIPTION
TOW BAR ASSEMBLY (COMPLETE)
SNAP RING, 3/4"
SHAFT, TOW BAR PIVOT, PIN w/KEEPER
TUBE, TOW BAR OUTER
PIN, LIFT CYLINDER
SHAFT, EXTEND CYLINDER
CYLINDER, WHEEL LIFT TILT
DECAL, SAFETY CHAIN WARNING
GUARD, TOW BAR BUMPER
CROSSTUBE, TOW BAR
GREASE FITTING
PIN, TOW BAR PIVOT
NUT, 7/8"-9 NYLOK HEX
SNAP RING, 1-1/4"
TUBE, TOW BAR INNER
CYLINDER, TOW BAR EXTEND
VI-27
QTY
-2
1
1
2
1
2
1
2
1
3
1
1
5
1
1
Section VI - PARTS (cont'd)
OPTIONAL EQUIPMENT
TOW BAR ASSEMBLY
ID
NO
PART
NO
1
2
0301798
0304220
DESCRIPTION
TOW BAR CYLINDER (COMPLETE)
SEAL KIT
VI-28
QTY
1
--
Section VI - PARTS (cont'd)
OPTIONAL EQUIPMENT
TOWING SLING
ID
NO
PART
NO
1
2
3
4
5
6
7
8
9
0800608
0800609
0701919
0800873
0400105
0400156
0701920
0400392
0300176
DESCRIPTION
CHAIN KEEPER, LEFT
CHAIN KEEPER, RIGHT
TOW SLING BELT
BELT RETAINER
SCREW, 5/16"-18 X 1-1/4" SELF
CARRIAGE BOLT, 3/8"-16 X 1-1/4"
GRIP PLATE
NUT, 3/8"-16 NYLOK HEX
"J" HOOK ASSEMBLY
VI-29
QTY
1
1
2
2
8
8
2
8
2
NOTES
NOTES
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive ï Ooltewah, Tennessee 37363 ï (423) 238-7227
www.millerind.com