Century Formula I 411/412

CENTURY
L E G E N D A R Y
®
L E A D E R S H I P
OWNER'S MANUAL
FORMULA I
411 & 412 WRECKER
INSTALLATION, OPERATION, MAINTENANCE & PARTS
NOTE: MANUAL including SPECIFICATIONS, subject to change without notice
All ratings specified are based on structural factors only,
not vehicle capacities or capabilities.
CENTURY®
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive
Ooltewah, Tennessee 37363
Phone (423) 238-4171 • FAX (423) 238-5371
FORM NO. 0500744
REV. A
12 / 99
PRICE $25.00
LIMITED WARRANTY
MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as MILLER, warrants to
the original purchaser that each new MILLER wrecker or other MILLER products will be free from
defects in material and workmanship for a period of twelve (12) months from date placed in service,
but in no event shall such warranty period exceed twenty-four (24) months from date of manufacture
by MILLER. The purchaser must promptly notify MILLER in writing of any failure in material or
workmanship. In no event shall MILLER accept such notification later than twenty-four (24) months
from date of delivery or twelve (12) months from date placed in service, whichever is earlier.
MILLER's obligation under this warranty, statutory or otherwise, is limited to the repair or replacement
at the MILLER factory, or at a point designated by MILLER, of such part or parts as shall appear upon
inspection by MILLER to be defective in material or workmanship. New or remanufactured parts will be
used for any replacement at MILLER's option. This warranty is not transferable. This warranty does
not obligate MILLER to bear the cost of labor or transportation charges in connection with the repair or
replacement of any parts found to be defective, nor shall it apply to a product upon which repairs or
alterations have been made unless authorized by MILLER.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, MILLER MAKES NO OTHER
WARRANTY, EXPRESS OR IMPLIED, AND HEREBY DISCLAIMS ALL OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. MILLER shall in no event be liable for claimed downtime,
claimed loss of profits or goodwill, or any other special, incidental, indirect, or consequential damages
concerning or relating to any product or parts, whether based on negligence, strict liability, breach of
contract, breach of warranty, misrepresentation or any other legal theory, regardless of whether the
loss resulted from any general or particular requirement which MILLER knew or had reason to know
about at the time of sale.
MILLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, AS TO THE FINISHED PRODUCTS
MANUFACTURED OR SUPPLIED BY ANOTHER MANUFACTURER AND SUPPLIED BY MILLER
TO PURCHASER, including, but not limited to, any vehicle to which a MILLER product may be affixed
or any accessories or wire rope, and MILLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AS TO SUCH EQUIPMENT
OR PRODUCTS. This language shall in no way affect or diminish the rights of the purchaser to rely
on such warranties as are extended by such manufacturers or suppliers. MILLER shall, to the extent
permitted under applicable law, pass on to the purchaser such manufacturer's or seller's warranty.
MILLER, whose policy is one of continuous improvement, reserves the right to improve its products
through changes in design or materials as it may deem desirable without being obligated to incorporate
such changes in products previously sold. This warranty is not intended to cover or include the
following items, which are set forth by way of example and not limitation:
A. Normal deterioration of trim, paint, lettering, and appearance items due to wear or exposure to
weather, road conditions, road treatments, etc.
B. Any damage or defect due to accident, misuse, abuse, improper or unauthorized repairs, failure
to provide reasonable and necessary maintenance, or uses for which the equipment was not
designed or intended.
C. Alterations or modifications that affect performance, operation or reliability.
D. Normal maintenance parts including, but not limited to, wear pads, bushings, wire rope, mud
flaps, fenderettes, light bulbs, hydraulic oil, filters, and tow sling belts.
IT IS EXPRESSLY UNDERSTOOD THAT MILLER MAKES NO IMPLIED WARRANTY THAT MILLER
PRODUCTS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR MOVING PEOPLE OR FOR ANY
OTHER IMPROPER USE.
SERIAL NUMBER
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive
Ooltewah, Tennessee 37363
Telephone (423) 238-4171
Section VI - PARTS
This Section is provided by the manufacturer for the purpose of ordering
any component part of the Formula I Wheel Lift and 411 / 412 Wrecker
that may be required when part replacement is necessary.
Be certain to use only original equipment replacement parts for warranty
purposes as well as for keeping your Formula I Wheel Lift and 411 / 412
Wrecker in its original state and optimum operating capacities.
When ordering replacement or spare parts be sure to provide the following
information to the manufacturer’s Parts Department.
1.
2.
3.
4.
5.
6.
7.
Manual Number & Date of Publication
Manual Page Number
Page Title
Reference Number of Part Desired
Part Number
Part Description
Quantity of Part Desired
Providing this information will help ensure that the correct parts will be
delivered to you in an expedient manner. Should additional information be
required for repair or replacement of certain components, contact your
Wrecker Manufacturer Authorized Representative.
The Manufacturer reserves the right, without notice or obligation, to improve
or modify their products, which may change the specifications, models and
feature availability.
VI-1
Section VI - PARTS (cont'd)
FORMULA BODY ASSEMBLY
VI-2
Section VI - PARTS (cont'd)
FORMULA BODY ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
1
2
2
1
1
1
2
2
4
2
6
4
10
4
8
4
4
4
4
12
2
42
4
1
0300028
0301932
0302173
0302181
0302182
0302855
0303123
0303124
0303125
0303126
0303127
0303128
0400062
0400066
0400122
0400126
0400260
0400351
0400370
0400392
0400421
0400567
0400821
0703220
25
26
27
28
29
30
31
32
33
-34
16 FT.
2
2
1
1
1
2
1
1
-2
0703792
0704516
0705092
0707510
0708809
0708810
0710198
0801258
0802620
0802714
0802712
DESCRIPTION
STRIKER, TOOL COMPARTMENT
SAFETY CHAIN, 5/16" ALLOY
MUD FLAP
LT FIBERGLASS FENDER (OPT.)
RT FIBERGLASS FENDER (OPT.)
LATCH, TOOL COMPARTMENT DOOR
LIGHT, STOP & TURN, RED
LIGHT, BACKUP, CLEAR
MARKER, SEALED RED
MARKER, SEALED AMBER
GROMMET, MARKER LIGHT
GROMMET, TAIL LIGHT
SCREW, 1/4-20 X 3/4" THREAD CUTTING
SCREW, 1/4"-20 X 3/4" HEX HD CAP
SCREW, 3/8"-16 X 1-1/4" HEX HD CAP
SCREW, 3/8"-16 X 1" HEX HD CAP
SCREW, 5/8"-11 X 2" HEX HD CAP
NUT, #8-32 KEPS
CLIP, 1/4" TINNERMAN "U" TYPE
NUT, 3/8"-16 NYLOK
NUT, 5/8"-11 NYLOK
RIVET, 1/4" POP
SCREW, #8-32 RD HD
PLATE, ACCESS HOLE COVER
(FORMULA I, WHEEL LIFT ONLY)
MIRACLE SEAL
GUARD, CONTROL STATION
MUD FLAP BAR
BRACKET, "L" ARM STORAGE
RT MUD FLAP MTG ANGLE
LT MUD FLAP MTG ANGLE
BRACKET, MARKER LIGHT
SIDE TOOL BOX
BODY WELDMENT - 60 C.A. FI
BODY WELDMENT - 56 C.A. FI
BRACKET, "L" ARM STORAGE
VI-3
Section VI - PARTS (cont'd)
DAYTONA BODY ASSEMBLY
VI-4
Section VI - PARTS (cont'd)
DAYTONA BODY ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
1
4
32 FT.
2
2
1
1
4
2
2
4
2
6
4
8
4
16
4
8
4
4
16
4
12
2
42
32
1
0300028
0300032
0300844
0301932
0302173
0302181
0302182
0302855
0303123
0303124
0303125
0303126
0303127
0303128
0304264
0304480
0400062
0400066
0400122
0400126
0400260
0400351
0400370
0400392
0400421
0400567
0400821
0703220
29
30
31
32
33
34
35
36
37
4
4
2
2
1
1
1
2
1
--2
0703654
0704231
0704516
0705092
0707510
0708809
0708810
0710198
0802621
0802622
0802623
0802712
38
DESCRIPTION
STRIKER, TOOL COMPARTMENT
PLUG, 1" HOLE
SPONGE, 3/4" X 1/8" W/ ADHBK
SAFETY CHAIN, 5/16" ALLOY
MUD FLAP
LT FIBERGLASS FENDER (OPT.)
RT FIBERGLASS FENDER (OPT.)
LATCH, TOOL COMPARTMENT DOOR
LIGHT, STOP & TURN, RED
LIGHT, BACKUP, CLEAR
MARKER, SEALED RED
MARKER, SEALED AMBER
GROMMET, MARKER LIGHT
GROMMET, TAIL LIGHT
HINGE, DOOR
DOOR, DAYTONA BOX
SCREW, 1/4-20 X 3/4" THREAD CUTTING
SCREW, 1/4"-20 X 3/4" HEX HD CAP
SCREW, 3/8"-16 X 1-1/4" HEX HD CAP
SCREW, 3/8"-16 X 1" HEX HD CAP
SCREW, 5/8"-11 X 2" HEX HD CAP
NUT, #8-32 KEPS
CLIP, 1/4" TINNERMAN "U" TYPE
NUT, 3/8"-16 NYLOK
NUT, 5/8"-11 NYLOK
RIVET, 1/4" POP
SCREW, #8-32 RD HD
PLATE, ACCESS HOLE COVER
(FORMULA I, WHEEL LIFT ONLY)
PAD, DOOR CHECK
ANGLE DOOR CHECK
GUARD, CONTROL STATION
MUD FLAP BAR
BRACKET, "L" ARM STORAGE
RT MUD FLAP MTG ANGLE
LT MUD FLAP MTG ANGLE
BRACKET, MARKER LIGHT
BODY WELDMENT - 60 C.A. DAYTONA
BODY WELDMENT - 72 C.A. DAYTONA
BODY WELDMENT - 84 C.A. DAYTONA
BRACKET, "L" ARM STORAGE
VI-5
Section VI - PARTS (cont'd)
FORMULA I WHEEL LIFT ASSEMBLY
VI-6
Section VI - PARTS (cont'd)
FORMULA I WHEEL LIFT ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
13
1
2
1
2
1
1
6
1
1
8
1
1
8
1
*
2
1
1
1
4
2
1
4
1
1
1
2
2
1
1
1
2
0300113
0301197
0301397
0301398
0301601
0301850
0306748
0303016
0303018
0400139
0400141
0400353
0400366
0400392
0400398
0701941
0701956
0702131
0702546
0703345
0703422
0703640
0801009
0801011
0802820
0801073
0801074
0200040
0801448
0801687
0803639
0802610
0906575
-34
35
36
37
-4
4
8
8
0902835
0400260
0400264
0400421
0400506
DESCRIPTION
GREASE FITTING, ALEMITE
SPRING, DETENT
GREASE FITTING, ALEMITE
BALL, DETENT
CLAMP
SLIDE PAD, NYLATRON
BUSHING
BUSHING
SLIDE PAD, NYLATRON
SCREW, 3/8"-16 X 1-1/2" HEX SKT SET
SCREW, 3/8"-16 X 7/8" HEX HD CAP
SETSCREW, 3/8"-16 X 1/2" ALLEN HD
NUT, 1/4"-20 HEX
NUT, 3/8"-16 NYLOK HEX
NUT, 3/8"-16 HEX JAM
WHEEL LIFT MOUNTING SPACER
SCREW, 1/2"-13 X 1" HEX HD CAP
SHAFT, CYLINDER
SPACER
SHAFT, EXTEND CYLINDER
HOSE GUARD
THRUST WASHER
UPPER SHAFT WELDMENT, BOOM
SHAFT WELDMENT, ARM
SHAFT, LIFT CYLINDER
PIN, CROSSTUBE PIVOT
CROSSTUBE, INNER WELDMENT
UPPER ARM CASTING
LOWER SHAFT WELDMENT, BOOM
OUTER BOOM WELDMENT
INNER BOOM WELDMENT
FRAME WELDMENT
UPPER ARM ASSY - INCLUDES
ITEMS 8 & 28
WHEEL LIFT MOUNTING HARDWARE
SCREW, 5/8"-11 X 2" HEX HD CAP
SCREW, 5/8"-11 X 2-1/4" HEX HD CAP
NUT, 5/8"-11 NYLOK HEX
WASHER, 5/8" FLAT
VI-7
Section VI - PARTS (cont'd)
FORMULA I WHEEL LIFT HYDRAULICS
VI-8
Section VI - PARTS (cont'd)
FORMULA I WHEEL LIFT HYDRAULICS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
1
6
1
1
4 FT.
1
2
1
2
1
2
1
1
1
2
2
1
1
2
6
6
1
1
1
1
1
6
1
1
1
20 FT.
2
2
2
2
2
2
1
0300010
0300040
0300052
0300055
0301674
0300071
0300113
0300133
0300142
0300206
0300209
0300660
0301375
0301377
0301397
0301402
0301425
0301473
0301485
0301522
0301696
0301731
0301825
0301854
0301855
0301900
0301902
0302341
0302904
0302905
0303193
0400069
0400140
0400362
040366
0400451
0400452
0703001
DESCRIPTION
3-SPOOL VALVE
CONNECTOR, 6MJ-8MB
ELBOW, 8MJ-10MB90
HOSEBARB, 12C4-12MP
HOSE, 3/4" RETURN
CLAMP, HOSE 1"
GREASE FITTING, ALEMITE
CLAMP, HOLDING VALVE
ELBOW, 6MJ-4MP90
BRANCHTEE, 6MJ-6MJ-4MP
ELBOW, 6MJ-6MP90
HOSE ASSEMBLY, 120"
ELBOW, 12MB-12FP90
TEE, 6MJ-6MJ-6MJ
GREASE FITTING, ALEMITE 90°
HOSE, LIFT CYLINDER, 45"
CONNECTOR, 6MJ-6MP
HOSE ASSEMBLY, 18"
HOSE ASSEMBLY, 81"
CONNECTOR, 6MJ-6MB
ELBOW, 6MJ-6FJX90
HOLDING VALVE, 4000 PSI
CYLINDER, EXTEND
VALVE, RESTRICTOR
TEE, 6MJ-6MJ-6MP
HOSE ASSEMBLY, 18"
HOSE ASSEMBLY, 35"
CYLINDER, LIFT
CYLINDER, TILT, L.H.
CYLINDER, TILT, R.H.
SKUFF JACKET
SCREW, 1/4"-20 X 2" RD HD SLOTTED
SCREW, 3/8"-16 X 4" HEX HD CAP
NUT, 3/8"-16 NYLOK HEX
NUT, 1/4"-20 HEX
WASHER, 1/4" FLAT
LOCKWASHER, 1/4" HELICAL
BRACKET, CHECK VALVE MOUNTING
VI-9
Section VI - PARTS (cont'd)
OUTER CROSSTUBE &
SLIDE-IN TIRE RESTRAINT ASSEMBLY
VI-10
Section VI - PARTS (cont'd)
OUTER CROSSTUBE &
SLIDE-IN TIRE RESTRAINT ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
--
1
0902456
--
1
0902457
1
2
3
4
5
6
7
8
9
10
11
12
13
14
2
2
2
2
2
2
2
2
2
2
2
1
1
1
0300113
0300341
0301417
0301956
0400367
0400393
0400451
0400559
0400560
0706688
0800590
0802069
0802070
0903478
15
1
0903479
16
17
18
1
1
2
0802359
0802360
0902382
DESCRIPTION
CROSSTUBE, LEFT OUTER,
W/ BASKET STRAP HOOKS (COMPLETE)
CROSSTUBE, RIGHT OUTER,
W/ BASKET STRAP HOOKS (COMPLETE)
GREASE FITTING, ALEMITE
KNOB
SPRING, PLUNGER PIN
STRAP, 9" RUBBER
NUT, 1/4"-20 NYLOK HEX
NUT, 3/8"-16 JAM HEX
WASHER, 1/4" FLAT
PIN, 3/16" X 1" ROLL
PIN, 5/32" X 1" ROLL
PIN, PLUNGER
HANDLE, TEE
HANDLE, LEFT PLUNGER
HANDLE, RIGHT PLUNGER
TIRE RESTRAINT, LEFT, W/ BASKET STRAP
SLOT
TIRE RESTRAINT, RIGHT, W/ BASKET STRAP
SLOT
CROSSTUBE, LEFT OUTER
CROSSTUBE, RIGHT OUTER
1" NYLON POLY COAT STRAP
VI-11
Section VI - PARTS (cont'd)
OUTER CROSSTUBE & 3-WAY PIVOT
TIRE RESTRAINT ASSEMBLY
VI-12
Section VI - PARTS (cont'd)
OUTER CROSSTUBE & 3-WAY PIVOT
TIRE RESTRAINT ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
6
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
2
2
0300113
0301399
0301956
0302640
0302641
0302642
0302648
0400161
0400207
0400349
0400367
0400390
0400412
0400451
0400480
0400560
0707505
0710227
0800583
0800590
0802187
0903489
0903490
0802675
0802676
0802679
0802680
0902382
0708915
DESCRIPTION
GREASE FITTING, ALEMITE
STRAP, TIE DOWN W/ RATCHET (OPT.)
STRAP, 9" RUBBER
PLUG, DRY-OUT HOLE
SPRING, PLUNGER PIN
SPRING, PIVOT LOCK
"T" HANDLE
BOLT, 3/8"-16 X 2-3/4" CARRIAGE (OPT.)
SCREW, 1/2"-20 X 1-1/4" HEX HD CAP
SCREW, 3/8"-16 X 3/4" SKT HD
NUT, 1/4"-20 HEX NYLOK
NUT, 3/8"-16 ESLOK JAM (OPT.)
NUT, 1/2"-20 HEX JAM
WASHER, 1/4" FLAT
WASHER, 3/8" FLAT (OPT.)
PIN, ROLL 5/32" X 1"
PIN, PLUNGER
PIN, DETENT
PIVOT, TIE DOWN (OPT.)
TEE HANDLE
SHAFT, PIVOT
"L" ARM, L.H.
"L" ARM, R.H.
OUTER CROSSTUBE, L.H.
OUTER CROSSTUBE, R.H.
END PLATE WELDMENT, L.H.
END PLATE WELDMENT, R.H.
1" NYLON, POLY-COAT STRAP (OPT.)
THREADED INSERT
VI-13
Section VI - PARTS (cont'd)
411 WRECKER ASSEMBLY
VI-14
Section VI - PARTS (cont'd)
411 WRECKER ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
1
6
4
6
1
4
4
1
6
9
9
4
8
9
1
1
1
1
1
1
2
1
1
1
1
1
0300219
0300109
0300110
0300113
0300251
0300679
0400060
0400121
0400122
0400260
0400421
0400452
0400482
0400506
0703082
0703137
0703965
0704745
0704746
0704747
0706668
0800941
0801373
0801376
0801510
0900007
DESCRIPTION
WIRE ROPE, 3/8" X 100', 6 X 19 IPS
SNAP RING, 1-1/2"
SNAP RING, 1"
GREASE FITTING, ALEMITE
WINCH, HLC-246 LEFT REAR
SLIDE PAD, NYLATRON
SCREW, 1/4"-20 X 1/2" HEX HD CAP
SCREW, 3/8"-16 X 3/4" HEX HD CAP
SCREW, 3/8"-16 X 1-1/4" HEX HD CAP
SCREW, 5/8"-11 X 2" HEX HD CAP
NUT, 5/8"-11 NYLOK
WASHER, 1/4" LOCK
WASHER, 3/8" LOCK
WASHER, 5/8" FLAT
PIN, EXT CYLINDER PIVOT
SHAFT, EXT CYLINDER OUTER BOOM
RETAINER, BOLT-ON PAD
SHAFT, BOOM LIFT PIVOT
SHAFT, LOWER LIFT CYLINDER
SHAFT, BOOM PIVOT
SHIM, WINCH MOUNTING
INNER BOOM WELDMENT
OUTER BOOM WELDMENT
WRECKER FRAME, SINGLE WINCH
DIP STICK WELDMENT
BOOM END SWIVEL ASSEMBLY
VI-15
Section VI - PARTS (cont'd)
411 WRECKER HYDRAULICS
VI-16
Section VI - PARTS (cont'd)
411 WRECKER HYDRAULICS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
REF.
1
2
3
2
2
2
1
1
1
4
2
1
1
2
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
2
6
2
6
2
2
1
1
0300010
0300010
0300041
0300044
0300052
0300055
0300071
0300090
0300133
0300136
0300142
0300147
0300206
0300209
0300229
0300286
0300288
0300660
0301207
0301334
0301375
0301388
0301405
0301425
0301470
0301471
0301547
0301696
0301731
0301755
0301780
0301790
0301902
0301964
0301965
0302356
0302777
0400069
0400140
0400366
0400392
0400451
0400452
0700238
0705085
DESCRIPTION
VALVE, 3 SPOOL CONTROL
VALVE, 3 SPOOL CONTROL
CONNECTOR, 8MJ-8MB
CONNECTOR, 6MJ-8MB
ELBOW, 8MJ-10MB90
HOSE BARB, 12C4-12MP
CLAMP, HOSE 1"
MOTOR, HYDRAULIC
CLAMP, 3" - 4", CK VALVE RET
RETURN LINE FILTER ASSY
ELBOW, 6MJ-4MP90
STREET ELBOW, 4MP-4FP90
TEE, BRANCH 6MJ-6MJ-4MP
ELBOW, 6MJ-6MP90
ELBOW, 8MJ-8MP90
ADAPTOR, H.P.C.O.
ELBOW, 90°, 3/4" NPT STREET
HIGH PRESSURE HOSE ASSY, 120"
HOSE ASSY, 72"
GROMMET, CATERPILLAR
ELBOW, 12MB-12FP90
ELBOW, 8MJ-8MB90
BENT TUBE ASSY, 4-1/2"
CONNECTOR, 6MJ-6MP
ELBOW, 6MJ-8MB90
HOSE ASSY, 30"
ELBOW, 8MJ-12MB90
ELBOW, 6MJ-6FJX90
HOLDING VALVE, 4000 PSI
BOOM EXTEND CYLINDER
CONNECTOR, 8MJ-12MB
HOSE ASSY, 15"
HOSE ASSY, 35"
HOSE ASSY, 65"
HOSE ASSY, 131"
BOOM LIFT CYLINDER
HOSE ASSY, 16"
SCREW, 1/4"-20 X 2" RD HD
SCREW, 3/8"-16 X 4" HEX HD CAP
NUT, 1/4"-20 HEX
NUT, 3/8"-16 NYLOK HEX
WASHER, 1/4" FLAT
WASHER, 1/4" HELICAL LOCK
BRACKET, HOLDING VALVE
HOSE, 3/4" ID X 48" RETURN
VI-17
Section VI - PARTS (cont'd)
412 WRECKER ASSEMBLY
VI-18
Section VI - PARTS (cont'd)
412 WRECKER ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
2
6
4
6
1
1
4
4
2
12
9
9
4
16
9
1
1
1
1
1
1
4
1
1
1
1
2
0300219
0300109
0300110
0300113
0300250
0300251
0300679
0400060
0400121
0400122
0400260
0400421
0400452
0400482
0400506
0703082
0703137
0703965
0704745
0704746
0704747
0706668
0800942
0801373
0801375
0801510
0900007
DESCRIPTION
WIRE ROPE, 3/8" X 100', 6 X 19 IPS
SNAP RING, 1-1/2"
SNAP RING, 1"
GREASE FITTING, ALEMITE
WINCH, HLC-246 RIGHT REAR
WINCH, HLC-246 LEFT REAR
SLIDE PAD, NYLATRON
SCREW, 1/4"-20 X 1/2" HEX HD CAP
SCREW, 3/8"-16 X 3/4" HEX HD CAP
SCREW, 3/8"-16 X 1-1/4" HEX HD CAP
SCREW, 5/8"-11 X 2" HEX HD CAP
NUT, 5/8"-11 NYLOK
WASHER, 1/4" LOCK
WASHER, 3/8" LOCK
WASHER, 5/8" FLAT
PIN, EXT CYLINDER PIVOT
SHAFT, EXT CYLINDER OUTER BOOM
RETAINER, BOLT-ON PAD
SHAFT, BOOM LIFT PIVOT
SHAFT, LOWER LIFT CYLINDER
SHAFT, BOOM PIVOT
SHIM, WINCH MOUNTING
INNER BOOM WELDMENT, DUAL
OUTER BOOM WELDMENT
WRECKER FRAME, DUAL WINCH
DIP STICK WELDMENT
BOOM END SWIVEL ASSEMBLY
VI-19
Section VI - PARTS (cont'd)
412 WRECKER HYDRAULICS
VI-20
Section VI - PARTS (cont'd)
412 WRECKER HYDRAULICS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
REF.
1
4
4
2
2
2
2
1
1
4
2
1
1
4
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
2
6
2
6
2
2
1
1
0300010
0300011
0300041
0300044
0300052
0300055
0300071
0300090
0300133
0300136
0300142
0300147
0300206
0300209
0300229
0300286
0300288
0300660
0301207
0301334
0301375
0301388
0301405
0301425
0301470
0301471
0301547
0301696
0301731
0301755
0301780
0301790
0301893
0301902
0301964
0301965
0302356
0302777
0400069
0400140
0400366
0400392
0400451
0400452
0700238
0705085
DESCRIPTION
VALVE, 3 SPOOL CONTROL
VALVE, 4 SPOOL CONTROL
CONNECTOR, 8MJ-8MB
CONNECTOR, 6MJ-8MB
ELBOW, 8MJ-10MB90
HOSE BARB, 12C4-12MP
CLAMP, HOSE 1"
MOTOR, HYDRAULIC
CLAMP, 3" - 4", CHK VALVE RET
RETURN LINE FILTER ASSY
ELBOW, 6MJ-4MP90
STREET ELBOW, 4MP-4FP90
TEE, BRANCH 6MJ-6MJ-4MP
ELBOW, 6MJ-6MP90
ELBOW, 8MP-8MJ90
ADAPTOR, H.P.C.O.
ELBOW, 90°, 3/4" NPT STREET
HIGH PRESSURE HOSE ASSY, 120"
HOSE ASSY, 72"
GROMMET, CATERPILLAR
ELBOW, 12MB-12FP90
ELBOW, 8MJ-8MB90
BENT TUBE ASSY, 4-1/2"
CONNECTOR, 6MJ-6MP
ELBOW, 6MJ-8MB90
HOSE ASSY, 30"
ELBOW, 8MJ-12MB90
ELBOW, 6MJ-6FJX90
HOLDING VALVE, 4000 PSI
BOOM EXTEND CYLINDER
CONNECTOR, 8MJ-12MB
HOSE ASSY, 15"
HOSE ASSY, 84"
HOSE ASSY, 35"
HOSE ASSY, 65"
HOSE ASSY, 131"
BOOM LIFT CYLINDER
HOSE ASSY, 16"
SCREW, 1/4"-20 X 2" RD HD
SCREW, 3/8"-16 X 4" HEX HD CAP
NUT, 1/4"-20 HEX
UT, 3/8"-16 NYLOK HEX
WASHER, 1/4" FLAT
WASHER, 1/4" HELICAL LOCK
BRACKET, HOLDING VALVE
HOSE, 3/4" ID X 48" RETURN
VI-21
Section VI - PARTS (cont'd)
FORMULA I (W/O WRECKER) SUCTION
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
1
2
1
2
1
4
4
1
1
1
0300055
0300071
0300136
0300288
0300347
0400126
0400392
0702741
0705085
0800788
DESCRIPTION
HOSEBARB, 12C4-12MP
CLAMP, HOSE 1"
RETURN LINE FILTER ASSEMBLY
ELBOW, STREET 90° 3/4" MALLEABLE BLACK
PLUG, 1/2" SQ HD BLACK
SCREW, 3/8"-16 X 1" HEX HD CAP
NUT, 3/8"-16 NYLOK HEX
RESERVOIR CAP
HOSE, RETURN 3/4" X 48"
RESERVOIR WELDMENT
VI-22
Section VI - PARTS (cont'd)
411 & 412 WRECKER SUCTION
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
1
9 FT
1
1
1
1
2
1
0300056
0300058
0300071
0300446
0302108
0302959
0303099
HC1338
DESCRIPTION
BARB, 16C4-16MP
HOSE, SUCTION 1"
CLAMP, HOSE 1"
PLUG, PIPE 3/4" NPT MALE
BUSHING, REDUCER, 20MP-16FP
NIPPLE, 1" NPT X 3"
ELBOW, STREET 45° 1" MALLEABLE BLACK
VALVE, GATE 1" BRASS
VI-23
Section VI - PARTS (cont'd)
CONTROL & CROSSROD ASSEMBLY
VI-24
Section VI - PARTS (cont'd)
CONTROL & CROSSROD ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
21
4
2
2
2
2
2
6
6
21
21
6
7
14
7
5
2
1
2
4
1
2
14
7
3
2
2
0300122
0300834
0300835
0300837
0302856
0302917
0302967
0400066
0400370
0400390
0400393
0400452
0400527
0400542
0400543
0701099
0701927
0703501
0704528
0704529
0704530
0704517
0704527
0800604
0801309
0801310
0801311
DESCRIPTION
GROMMET, SPLIT PLASTIC
KNOB, CABLE "IN-OUT" (RED)
KNOB, WRECKER BOOM "UP-DN" (BLACK)
KNOB, WRECKER BOOM "IN-OUT" (BLACK)
KNOB W/L "TILT" (GRAY)
KNOB, W/L "IN-OUT" (GRAY)
KNOB, W/L "UP-DN" (GRAY)
SCREW, 1/4"-20 X 3/4" HEX HD CAP
CLIP, 1/4" TINNERMAN
NUT, 3/8"-16 HEX JAM ESLOK
NUT, 3/8"-16 HEX JAM
LOCKWASHER, 1/4" HELICAL
CLEVIS PIN, 5/16" X 5/8" COTTERLESS
COTTER PIN, 3/16" X 1-1/4"
COTTER PIN, 1/8" X 3/4"
EXTENSION, CONTROL ROD LONG
EXTENSION, CONTROL ROD SHORT
ANGLE, CROSSROD BEARING
CROSSROD - W/L
CROSSROD - WRECKER
CROSSROD - TILT
CHANNEL, CROSS ROD BEARING
LEVER, CONTROL
ARM, CROSS CONTROL
CONTROL ROD, SHORT
CONTROL ROD, MEDIUM
CONTROL ROD, LONG
VI-25
Section VI - PARTS (cont'd)
BOOM END SWIVEL ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
1
1
1
1
1
1
2
2
1
1
-1
1
0300108
0300022
0300113
0301531
0400060
0400392
0400393
0400452
0700032
0700056
0700166
0702285
0800003
DESCRIPTION
SNAP RING, 2-1/2" DIA EXT
6" SHEAVE
GREASE FITTING
"U" BOLT (FROM 3/8" CABLE CLAMP)
SCREW, 1/4"-20 X 1/2" HEX HD CAP
NUT, 3/8"-16 HEX NYLOK
NUT, 3/8"-16 HEX JAM
1/4" LOCKWASHER
SHAFT RETAINER
SHAFT
WASHER-SPACER
CABLE GUIDE
BOOM END SWIVEL
VI-26
Section VI - PARTS (cont'd)
WINCH CLUTCH CONTROL ASSEMBLY
2 ASSEMBLIES REQUIRED FOR 412 (DUAL WINCH)
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
1
1
1
1
1
0300845
0301532
0301588
0400116
0400122
--
1
0400126
6
7
8
9
10
11
12
13
14
15
16
1
2
1
4
1
1
2
1
1
1
1
0400150
0400482
0400393
0400492
0400537
0400546
0400560
0702408
0800780
0800781
0800779
DESCRIPTION
SPRING, COMPRESSION
"T" HANDLE
ADJUSTING YOKE
SCREW, 5/16"-18 X 1/2" SQ HD SET
SCREW, 3/8"-16 X 1-1/4" HEX HD CAP
(SINGLE WINCH)
SCREW, 3/8"-16 X 1" HEX HD CAP
(DUAL WINCH)
SCREW, 3/8"-16 X 2-1/2" HEX HD CAP
WASHER, 3/8" LOCK
NUT, 3/8"-16 JAM
WASHER, 1/2" FLAT
PIN, 1/2" X 1-1/2" CLEVIS
PIN, 1/8" X 1-1/4" COTTER
PIN, 5/32" X 1" ROLL
MOUNTING CHANNEL
CONTROL ROD, SINGLE WINCH
CONTROL ROD, DUAL WINCH
WELDMENT, BELL CRANK
VI-27
Section VI - PARTS (cont'd)
HYDRAULIC WINCH
VI-28
Section VI - PARTS (cont'd)
HYDRAULIC WINCH
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
4
1
10
8
4
1
1
1
1
4
2
2
1
2
4
2
1
1
2
1
1
4
1
2
1
2
316083
316084
324161
328134
332007
334164
338003
338273
342018
342024
342027
344008
356902
357480
368009
370001
400001
402002
412003
412045
414038
414045
414282
416040
416059
416084
416109
418177
438014
442184
442205
450006
450016
456006
456008
468002
468011
472013
486009
486017
494001
494002
518014
518015
DESCRIPTION
BEARING CAP
BEARING CAP
JAW CLUTCH
COVER
DRUM "Y"
GEAR L.H. 46:1
HOUSING, CLUTCH
HOUSING, GEAR
KEY
KEY
KEY
LEVER, SHIFTER
SHAFT, SHIFTER
SHAFT, DRUM "Y"
WORM L.H. 46:1
YOKE
BALL, POPPET
BEARING, BALL
BUSHING
BUSHING
SCREW, 1/4-20 X 3/4" HEX HD CAP
SCREW, 1/4-20 X 7/8" HEX HD CAP
SCREW, 3/8-16 X 3/4" HEX HD CAP
SCREW, 1/4-20 X 1-1/4" SKT HD LESS SET
SCREW, 3/8-16 X 3/8" SKT HD LESS SET
SCREW, 1/4-20 X 1/2" SQ HD SET
SCREW, 5/16-18 X 1/2" SQ HD SET
LOCKWASHER, 3/8 MED SECT
DRAG BRAKE
GASKET
GASKET
KEY, BARTH
KEY, BARTH
FITTING, LUBE
FITTING, RELIEF
REDUCER
PIPE PLUG
PLASTIC PLUG
OIL SEAL
OIL SEAL
SPRING, POPPET
SPRING
THRUST WASHER
THRUST WASHER
VI-29
Section VI - PARTS (cont'd)
HYDRAULIC CYLINDERS - WHEEL LIFT
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
1
1
0303681
0304573
REF.
NO.
NO.
REQ'D
PART
NUMBER
DESCRIPTION
1
2
3
1
1
2
0303675
0303674
0304492
HYDRAULIC CYLINDER., TILT (COMPLETE) L.H.
HYDRAULIC CYLINDER., TILT (COMPLETE) R.H.
SEAL KIT, TILT CYLINDER
REF.
NO.
NO.
REQ'D
PART
NUMBER
DESCRIPTION
1
2
1
1
0301825
0304086
DESCRIPTION
HYDRAULIC CYLINDER, LIFT (COMPLETE)
SEAL KIT, LIFT CYLINDER
HYDRAULIC CYLINDER, EXTEND (COMPLETE)
SEAL KIT, EXTEND CYLINDER
VI-30
Section VI - PARTS (cont'd)
HYDRAULIC CYLINDERS - WRECKER
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
1
1
0302218
0300625
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
1
1
0301755
0300624
DESCRIPTION
HYDRAULIC CYLINDER, LIFT (COMPLETE)
SEAL KIT, LIFT CYLINDER
DESCRIPTION
HYDRAULIC CYLINDER., EXTEND (COMPLETE)
SEAL KIT, EXTEND CYLINDER
VI-31
Section VI - PARTS (cont'd)
LIGHT KIT
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
2
2
4
0303123
0303124
0303128
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
2
6
0303125
0303126
0303127
DESCRIPTION
LIGHT, SEALED RED, STOP & TURN
LIGHT, SEALED WHITE, BACKUP
TAIL LIGHT GROMMET
DESCRIPTION
LIGHT, SEALED MARKER, RED
LIGHT, SEALED MARKER, AMBER
GROMMET
VI-32
Section VI - PARTS (cont'd)
LIGHT KIT (cont'd)
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
1
1
1
2
2
1
1
1
0304147
0304152
0304151
0304150
0304153
0301505
0304148
0304149
DESCRIPTION
HOUSING
BULB
PIVOT SCREW
LOCKWASHER
NUT
MOUNTING BRACKET
MOUNTING SCREW
LIGHT, BACKUP (COMPLETE)
VI-33
Section VI - PARTS (cont'd)
LIGHTING ACCESSORIES - DECK MOUNT
VI-34
Section VI - PARTS (cont'd)
LIGHTING ACCESSORIES - DECK MOUNT
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
2
1
1
2
8
2
2
2
8
2
2
8
2
22
2
0300076
0300117
0300273
0301359
0302158
0400039
0400057
0400061
0400062
0400132
0400366
0400367
0400392
0400452
0400480
0710028
LICENSE PLATE HOLDER
RUBBER GROMMET
LICENSE PLATE ILLUMINATOR
WRECKER SPECIAL LIGHT
SPOTLIGHT W/GASKET
SCREW, #10-32 X 3/4" SELF-TAPPING
SCREW, 1/4"-20 X 1-1/2" HEX HD CAP
SCREW, 1/4"-20 X 3/4" PAN HD
SCREW, 1/4"-20 X 3/4" THD CUT HEX HD
SCREW, 3/8"-16 X 1-1/2" HEX HD CAP
NUT, 1/4"-20 HEX PLAIN
NUT, 1/4"-20 NYLOK HEX
NUT, 3/8"-16 HEX HD NYLOK
LOCKWASHER, 1/4"
WASHER, 3/8" FLAT
ANGLE, PYLON BASE REINFORCING
17
2
-------
0710030
0710031
0710032
0710033
0710034
0710035
0710036
GASKET,
GASKET,
GASKET,
GASKET,
GASKET,
GASKET,
GASKET,
18
2
0801777
"T" BOLT ADAPTER
19
1
-------
0802832
0802833
0802834
0802835
0802836
0802837
0802838
LIGHT MOUNTING PYLON - 22"
LIGHT MOUNTING PYLON - 26"
LIGHT MOUNTING PYLON - 33"
LIGHT MOUNTING PYLON - 36"
LIGHT MOUNTING PYLON - 40"
LIGHT MOUNTING PYLON - 42"
LIGHT MOUNTING PYLON - 45"
20
1
0802885
BRACKET, LICENSE PLATE MOUNTING
DESCRIPTION
VI-35
PYLON
PYLON
PYLON
PYLON
PYLON
PYLON
PYLON
BASE
BASE
BASE
BASE
BASE
BASE
BASE
-
22"
26"
33"
36"
40"
42"
45"
PYLON
PYLON
PYLON
PYLON
PYLON
PYLON
PYLON
Section VI - PARTS (cont'd)
FOLD DOWN LIGHT BRACKET (PYLON)
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
2
2
6
2
2
2
2
1
1
1
1
1
0400126
0400381
0400392
0400463
0400464
0400543
0703886
0801120
0903130
0903131
0903132
0903133
DESCRIPTION
SCREW, 3/8"-16 X 1" HEX HD CAP
NUT, 5/16"-18 HEX
NUT, 3/8"-16 NYLOK HEX
WASHER, 5/16" FLAT
LOCKWASHER, 5/16" HELICAL
PIN, 1/8" X 3/4" COTTER
ROD, CONNECTING
TEE BOLT - FOLD DOWN LIGHT BRACKET
L.H. BOTTOM HINGE ASSEMBLY
R.H. BOTTOM HINGE ASSEMBLY
L.H. TOP HINGE ASSEMBLY
R.H. TOP HINGE ASSEMBLY
VI-36
Section VI - PARTS (cont'd)
LIGHTING ACCESSORIES - WINCH MOUNT
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
2
3
1
1
12
4
14
18
2
1
0300095
0300117
0300442
0301359
0400027
0400122
0400392
0400480
0800539
0801427
DESCRIPTION
SPOTLIGHT W/GASKET
RUBBER GROMMET
3 BAR LIGHT
WRECKER SPECIAL LIGHT
SCREW, #8-32 X 5/8" SELF-TAPPING
SCREW, 3/8"-16 X 1-1/4" HEX HD CAP
NUT, 3/8"-16 NYLOK HEX
FLAT WASHER, 3/8"
"T" BOLT ADAPTER
LIGHT BAR FOR WRECKER
VI-37
Section VI - PARTS (cont'd)
FOLD DOWN LIGHT BRACKET
(WINCH MOUNTED LIGHT BAR)
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
2
2
6
2
2
2
1
1
2
1
1
1
0400126
0400381
0400392
0400463
0400464
0400543
0703886
0801120
0900985
0900986
0900987
0900988
DESCRIPTION
SCREW, 3/8"-16 X 1" HEX HD CAP
NUT, 5/16"-18 HEX
NUT, 3/8"-16 NYLOK HEX
WASHER, 5/16" FLAT
LOCKWASHER, 5/16" HELICAL
PIN, 1/8" X 3/4" COTTER
ROD, CONNECTING
TEE BOLT - FOLD DOWN LIGHT BRACKET
L.H. BOTTOM HINGE ASSEMBLY
R.H. BOTTOM HINGE ASSEMBLY
L.H. TOP HINGE ASSEMBLY
R.H. TOP HINGE ASSEMBLY
VI-38
Section VI - PARTS (cont'd)
TOW SLING ADAPTERS - FORMULA I
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
2
2
8
8
8
2
2
2
2
2
2
1
1
1
1
2
2
0300004
0300113
0400105
0400156
0400392
0400568
0700154
0701919
0701920
0701921
0800590
0800608
0800609
0800692
0800693
0800823
0900176
DESCRIPTION
SPRING, PLUNGER
GREASE FITTING
SCREW, 5/8"-18 X 1-1/4" SELF-TAPPING
SCREW, 3/8"-16 X 1-1/4" FLAT HD SKT
NUT, 1/8"-16 NYLOK
ROLL PIN
PIN, PLUNGER
TOW SLING BELT
GRIP PLATE
BELT RETAINER
TEE HANDLE
CHAIN KEEPER, LEFT
CHAIN KEEPER, RIGHT
INNER ADJUSTMENT TUBE, LEFT
INNER ADJUSTMENT TUBE, RIGHT
MOUNTING BRACKET
"J" HOOK ASSY
VI-39
Section VI - PARTS (cont'd)
FORMULA I - DRAG WINCH
VI-40
Section VI - PARTS (cont'd)
FORMULA I - DRAG WINCH
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
REF.
2
2
2
1
1
1
1
1
1
1
1
1
1
1
3
1
1
1
2
6
6
2
2
4
6
2
4
8
2
2
1
2
1
0300010
0300040
0300041
0300052
0300055
0300057
0300071
0300090
0300251
0300286
0300660
0301375
0301388
0301415
0301444
0301471
0301547
0301780
0301790
0302031
0400122
0400140
0400196
0400197
0400260
0400392
0400417
0400421
0400482
0400491
0400492
0701756
0706668
0801029
DESCRIPTION
VALVE, 3-SPOOL CONTROL
CONNECTOR, 8MJ-8MP
CONNECTOR, 8MJ-8MB
ELBOW, 8MJ-10MB90
HOSE BARB, 12C4-12MP
RETURN HOSE, 3/4" ID X 48"
CLAMP, HOSE 1"
MOTOR, HYDRAULIC
WINCH, HLC-246 LEFT REAR
ADAPTER, H.P.C.O.
HIGH PRESSURE HOSE ASSEMBLY, 120"
ELBOW, 12MB-12FP90
ELBOW, 8MJ-8MB90
VALVE, 2-SPOOL CONTROL
CABLE TENSIONER, DRAGLINE
HOSE ASSEMBLY, 30"
ELBOW, 8MJ-12MB90
CONNECTOR, 8MJ-12MB
HOSE ASSEMBLY, 15"
HOLE PLUG
SCREW, 3/8"-16 X 1-1/4" HEX HD CAP
SCREW, 3/8"-16 X 4" HEX HD CAP
SCREW, 1/2"-13 X 1-1/4" SKT HD CAP
SCREW, 1/2"-13 X 2-3/4" HEX HD CAP
SCREW, 5/8"-11 X 2" HEX HD CAP
NUT, 3/8"-16 NYLOK HEX
NUT, 1/2"-13 HEX
NUT, 5/8"-11 NYLOK HEX
LOCKWASHER, 3/8" HELICAL
LOCKWASHER, 1/2" HELICAL
WASHER, 1/2" FLAT
SPACER TUBE
SHIM, WINCH MOUNTING
FRAME, DRAG WINCH
VI-41
Section VI - PARTS (cont'd)
WHEEL LIFT ATTACHMENTS
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
1
1
1
1
0300091
0400294
0400511
0801091
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
5
5
1
1
1
1
0400181
0400408
0400585
0703459
0801272
0801273
DESCRIPTION
BALL, TRAILER, 2" CHROME
SCREW, 3/4"-10 X 5-1/2" HEX HD CAP
LOCKWASHER, 3/4" HELICAL
TOWBALL BRACKET
DESCRIPTION
SCREW, 1/2"-13 X 1-1/2" HEX HD CAP
NUT 1/2"-13 NYLOK
HAIR PIN COTTER
OUTRIGGER BLADE
SPADE ATTACHMENT
SPADE PIN
VI-42
Section VI - PARTS (cont'd)
THROTTLE CONTROL
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
1
1
1
0300683
0300684
0900377
DESCRIPTION
THROTTLE CONTROL, 16' - 60 C.A.
THROTTLE CONTROL, 18' - 84 C.A.
KIT, THROTTLE, FORD & CHEVY
VI-43
Section VI - PARTS (cont'd)
WIRING KIT
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
1
1
1
1
1
0303110
0303111
0303112
0303153
0301671
DESCRIPTION
FRONT HARNESS & JUNCTION BOX
REAR HARNESS
WORK LIGHT HARNESS
BACK UP ALARM HARNESS
4 POLE SKT & HARNESS
VI-44
Section VI - PARTS (cont'd)
OPTIONAL PTO PANEL
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
2
3
4
5
6
7
8
1
2
2
2
2
2
1
1
0304155
0304156
0304157
0304158
0304166
0304160
0304161
--
9
10
11
12
13
14
15
1
2
1
2
1
1
3
0304163
0304162
0304154
0304006
0304164
0301503
0304165
DESCRIPTION
SWITCH PANEL HOUSING
SCREW, #10-32 X 3-3/8", MTG
LOCKWASHER, #10 EXT TOOTH
WASHER, #10 FLAT
NUT, 10-32
JAM NUT
ACTUATOR DISK
PTO CABLE, 14 FT
(*SPECIFY MAKE & MODEL OF TRUCK)
PTO KNOB
CIRCUIT BREAKER, 40 AMP
SWITCH, DOUBLE POLE, SINGLE THROW
SWITCH, SINGLE POLE, SINGLE THROW
PTO LIGHT SWITCH
RING CONNECTOR
SPADE CONNECTOR
VI-45
NOTES
NOTES
CENTURY®
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive • Ooltewah, Tennessee 37363 • (423) 238-4171
www.millerind.com