Siai Marchetti SF 260 Instruction Manual

Thank you for choosing CYmodel
Global : www.cymodel.com
Australia : www.austars-model.com
Italia : www.biellaexpress.com
Siai Marchetti SF-260
Instruction Manual
Before commencing assembly, please read these instructions thoroughly.
SAFETY PRECAUTIONS
This radio control model is not a toy!
lFirst-time builders should seek advice from people having building
experience in order to assemble the model correctly and to produce
its performance to full extent.
lAssemble this kit only in places out of children ,s reach!
lTake enough safety precautions prior to operating this model.
You are responsible for this model ,s assembly and safe operation!
lAlways keep this instruction manual ready at hand for quick
reference,even after completing the assembly.
lCould cause serious injury or even death
SPECIFICATION
Wing span.............. 2286 mm (90 in)
Wing area................62.8 dm2 (974 sq.in)
Empty weight.........7.3 kg
Total length............1890 mm (70.5 in)
Engine.......................35-50 cc gas engine
Radio.........................6 channels 8 servos
Item Nr: Cy8124B
Designed and Manufactured by : CYmodel
Http : // www.cymodel.com
REQUIRED FOR OPERATION (Purchase separately)
A minimum 6 channel radio for airplanes (with 8 servos).
And dry batteries.
1
4
CAUTION: Only use a minimum 6 channel radio for
airplanes! (No other radio may be used!)
!
5
A minimum 6 channel
transmitter for airplanes.
Silicone Tube
Fuel Filter
engine fuel
required for engine starting
!
WARNING: Normal gasoline cannot
be used with glow engines.
Fuel Pump
Plug Wrench
12 AA-size Batteries
For handing the radio properly.refer to its instruction manual.
2
36
Engine and Muffler
Glue
Epoxy Glue
Instant glue
Model Airplane engine
35-50 cc gas engine
37
Other equipment for enhancing
airplane operation & perormance
Muffler
Glow plug
3
Purchase a propeller that
will match your engine
Propeller splinner
12V Battery (for starter)
Engine Starter
TOOLS REQUIRED ( Purchase separately)
Sharp Hobby Knife
Needle Nose Pliers
Phillips Screw Driver
Awl
Wire Cutters
Scissors
BEFORE YOU BEGIN
. Read through the manual before you begin ,so you will have an overall idea of what to do.
2 . Check all parts .if you find any defective or missing parts .contact your local deater.
3 . Symbols used throughout this instruction manual,comprise.
1
A
B
Apply epoxy glue.
Drill holes with the specified
Diameter(here:2mm)
Must be purchased
separately!
Apply instant glue
(CA glue,super glue).
Ensure smooth non-binding
movement while assembling.
Pay close attention
here!
Assemble left and right
Sides the same way.
Cut off shaded portion.
2mm
Cut off excess.
2
£¡Warning!
!
Do not overlook this symbol.
Accessory list for this page.
!
3
Install the lamp-chimney
4
Install the lamp-chimney
5
Install the lamp-chimney
Hinge
- - -10
1
Epoxy pin hings to aileron steadily
L
R
£¡Warning!
!
Securely glue together ,if coming
off during . You will lose control
of your airplane which leads to accidents!
A
B
Hinge
- - -1 0
2
Install the lamp-chimney
10mm
6mm
Blcak line
Battery
A
Red line
3
B
8
Accessory list for this page.
!
M4X35mm Screw
----4
Rod adjuster
----8
Horn
----4
----4
M4X20mm screw
--2
M4X20mm screw
------4
Connecting rod head
----4
2.5X85mm Rod
Screw
----8
6
M3X10mm
R
M4X20mm screw
--2
M4X20mm screw
------4
Screw
----4
------4
700 mm steel wire
5.2mm Collar
------4
Rod
5.2mm Collar
----2
3X3mm screw
-----2
-----2
3mm Nut
----2
4X4mm screw
-----4
M3X20mm
M4 Lock Nut
----2
-----2
----4
M3X25mm
------8
M4 Lock Nut
2X10mm Screw
----8
L
3X16mm Tp screw
Install the main landing gear
3X3mm screw
-----2
4x4mm Screw
4X4mm screw
----2
Screw
-----4
----4
9
Install the aileron
Assemble the landing gear to the wing with screw
3X16mm Tp screw
------8
7
10
Install the aileron servo
L
Aileron
servo
L
Assemble the front-wheel drive
R
M3X10mm
Screw
----4
700 mm steel wire
----2
M4X35mm
Connecting rod head
----4
2.5X85mm Rod
----4
M3X25mm
Screw
----8
M3X20mm
Screw
----4
Screw
Rod
----4
----2
Rod adjuster
----8
3mm Nut
Horn
----2
----4
----4
4x4mm Screw
----2
2X10mm Screw
----8
4
R
!
13
Accessory list for this page.
3X20mm Tp screw
Pin hings
---3
-----4
5 mm Washer
Nylon nut
4
------1
M4 Lock Nut
------1
Assemble the wings to the fuselage
Hinge
---6
Nylon nut
4
11
Assemble the front-wheel drive to the fuselage
with screw
14
Epoxy the horizontal tail
L
3X20mm Tp screw
R
-----4
A
£¡Warning!
!
Securely glue together ,if coming
off during . You will lose control
of your airplane which leads to accidents!
12
15
Assemble the front-wheel drive
Hinge
- - -6
Install the rudder
Pin hings
-----------3
5 mm Washer
------1
Warning!
M4 Lock Nut
Securely glue together. If coming off during flights,you'll
lose control of your airplane which leads to accidents!
------1
5
B
!
Horn
-------8
M2X8mm cap screw
-------2
-------6
Aluminum tube (3x6mm)
M4X35mm screw
10
Steel wire
-------1
4
M2x8mm cap screw
2
6
Copper joiner
----------4
4x35mm Screw
M3x20mm Screw
Connecting rod head
Fiberglass tube
Secure the servo. Install the nylon control horn
and connect the linkage
Rod adjuster
-------4
6
Copper joiner
2
3x25mm Screw
2
Elevator rod
2
Aluminum tube (3x6mm)
3
Rod adjuster
19
Assembly of the stabilizer
B
C
-----4
B
Aluminum tube (3x6mm)
C
4
2
4x35mm Screw
2
M2x8mm cap screw
3x25mm Screw
Connecting rod head
3mm Nut
2
2
-------- 2
Assemble the servo to the fuselage
Copper joiner
B=B
C=C
D=D
Horn
4
3
Steel wire
3mm Nut
2
16
18
Accessory list for this page.
--------6
Rod adjuster
-------4
M2X8mm cap screw
--------4
Rudder
servo
D
D
Securely glue together
,if coming off during flights.
You lose control of your airplane
which leads to accidents!
17
Elevator
servo
. Install the nylon control horn and connect
the linkage
Horn
-------2
-------2
Rod adjuster
-------2
M2X8mm cap screw
-------2
M4X35mm screw
-------1
20
M3x20mm Screw
Connecting rod head
6
----------2
Fiberglass tube
2
Elevator rod
2
A B
Elevator rod
6
Assembly of the fuel tank
3
3
!
23
Accessory list for this page.
Assemble the cowling to fuselage with screw
Nut ( 2mm )
1.8x450mm Throttle rod
1
Cap screw m3x16
1
Washer
Linkage Stopper
Set screw ( 3x4mm)
1
Rubber gasket
1
plywood (6mm)
Bland nut (3mm)
M3X16mm Cap Screw
---------7
A
Washer
---------------7
M3X16mm Cap Screw
---------5
Washer
---------------5
Rubber gasket
---------------7
Rubber gasket
---------------5
21
Assemble the engine
22
Mount the receiver and battery in the
fuselage
1.8x450mm Throttle rod
1
Linkage Stopper
1
B
24
25
Trim the surplus shaded portion away from the canopy
Assemble the canopy to the fuselage with TP screws
Nut ( 2mm )
1
Set screw ( 3x4mm)
1
(Battery)
(Receiver)
Throttle servo
M3X16mm Cap Screw
---------2
7
Washer
---------------2
Rubber gasket
---------------2
!
Accessory list for this page.
28
Epoxy the wheel wells to the holes
If you choose an air retractable
landing gear, the installing method
is as steps 26 to 30.
26
Epoxy the wheel wells to the holes
29
Assemble the front-wheel drive
27
Assemble of the landing gear
30
Three wheel retract system
L
5X45mm
R
Strut
Strut
Axletree
3-way
pressure inlet
-----2
Strut
3X20mm Tp screw
Air inlet
-----8
Air tank
5.2mm Collar
3-way
pressure inlet
Air tank
-----2
Quick release connector
3X3mm screw
-----2
Sw i tc h
4X4mm screw
-----2
8
31
33
Adjustment.
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Top view
32
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
47mm 54mm
AILERON
Adjustment.
Side view
Top view
34
CG
60mm 60mm
Top view
Centre of Gravity.
Never fly before checking the Cg s required position.
In order to obtain the CG specified ,reposition the
receiver and battery.
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Side view
Adjustment.
!
Warning!
NEVER fly the model
without well balancing.
35
5
Spread a diagram
9