Full X Door - Rustica Hardware

T Ro
Ur
CTI ONS
F u l l X I NDS o
INSTAL L ATI ON
Assembly Instructions
RH
•••••••••••••••••••••••••••••••••••••••••
oG
l s EaR
n dHPO
aL
r tE
sS
H To
AN
I N S TA L L AT I O N
I N S T RU C T I O N S
Tools Needed
If any of the slats have been damaged during shipping,
call us at 800-891-8312 and we will expedite a replacement slat. Lay out your Door parts according to the
illustration shown below to accurately identify which
part needs to be replaced, if any.
Drill with Phillips bit
Ratchet with socket
Parts Included
D1
D1
A3
C1
A4
A1 L
B1
B2
B2
B2
B2
B2
B2
B3
A6
A1 R
A5
D1
A2
Description
D1
Qty
Description
Qty
A1
Side Style L
1
A6
Diagonal Rail, partial
1
A1
Side Style R
1
B1
Left Side Slats
1
A2
Bottom Rail
1
B2
Middle Slats
6*
A3
Top Rail
1
B3
Right Side Slat
1
A4
Diagonal Rail, full
1
C1
1-1/4” Grabber Screws
15*
A5
Diagonal Rail, partial
1
D1
6” Timberlocks
4*
* Quantities will vary depending on Door size. All quantities in this table are for an average single Door order size.
RH
•••••••••••••••••••••••••••••••••••••••••
D iG
mEeR
n sH
i oO
n sL E S
HAN
I N S TA L L AT I O N
I N S T RU C T I O N S
5”
5”
4-1/8” Typical
6”
RH
•••••••••••••••••••••••••••••••••••••••••
HsA
Nb
Gl y
ER
Ht rOu L
Ei o
Sn s
A
s
e
m
I
n
s
c
t
I N S TA L L AT I O N I N S T RU C T I O N S
Assembling Your Door
1.
We recommend a dry assembly to ensure all
parts fit.
PLEASE NOTE: These instructions
are specific to a particular door size and
type. Adjustments may be needed on
your part for changes in specifications
and measurements, as well as door types
that are different than these.
Lay out A1 (L), A2, and A3 with the large mortised grooves facing in and with the small grooves
on A1 L and A2 on the bottom edge of the door.
Beginning with B1, slide each of the B slats into
the one to its right.
2. Once all the (B) slats are together in position,
place the bottom slots (tongues) into the
groove along the top of A2.
A3
A1
L
B1 B2 B2
B2 B2 B2 B2 B3
A3
A1
R
A2
A2
3. Slide slat A3 down to cover the tops of all
4.
Slide slat A1 L to the right.
5.
Slide slat A1 R to the left.
B slats.
A3
A1
L
A1
R
RH
•••••••••••••••••••••••••••••••••••••••••
HsA
Nb
Gl y
ER
Ht rO
L
Ei oSn s
A
s
e
m
I
n
s
u
c
t
I N S TA L L AT I O N I N S T RU C T I O N S
6.
Use the 6” Timber Locks to fasten A1 L, A1
R, and A2 and A3 together. Use your fingers
and a wrench to fasten the Timberlocks,
straight in, avoid going in at an angle. Have a
partner help keep the rails square as you install
the Timberlocks.
7.
Lay A4 over the top of all B slats.
Use a drill with a Phillips bit to
attach.
8.
Place slats A5 and A6 across all B
slats to form an X, corner to corner.
Use the 1-1/4” Grabber Screws to
attach.
A6
A4
A5
9.
Your Door is ready to hang.
RH
•••••••••••••••••••••••••••••••••••••••••