Half X Door.indd - Rustica Hardware

H alf X D oor
INSTAL L ATI ON
I NSTRU CTI ONS
Assembly Instructions
RH
•••••••••••••••••••••••••••••••••••••••••
6.3.2016
oG
l s EaR
n dHPO
aL
r tE
sS
H To
AAssembly
N
Instructions
I N S TA L L AT I O N
I N S T RU C T I O N S
To o ls Needed
Ratchet with 7/16” socket
If any of the stiles, slats or rails have been damaged during
shipping, call us at 800-891-8312 and we will expedite a
replacement slat. Lay out your Door parts according to the
illustration shown below to accurately identify which part
needs to be replaced, if any.
Drill with Phillips bit
Lay all parts out on a flat
surface as shown here.
PLEASE NOTE: These instructions are specific to a particular door size and
type. Adjustments may be needed on your part for changes in specifications
and measurements, as well as door types that are different from these.
Parts Included
A4
D1
D1
C1
C2
C2
C2
C2
C2
C2
C3
A1
L
A1
R
D1
D1
E1
A3
B2
B2
B2
B2
B2
B2
A1 L
Side Stile Left
1
A1 R
Side Stile Right
1
A2
Bottom Rail
1
A3
Middle Rail
1
A4
Top Rail
1
A5,
Diagonal Rails
A6, A7
1 each
B1, C1 Slats w/ 2 side tongues
1 each
B3, C3 1 Groove Slats
B3
A6
A7
D1
Qty
B2, C2 Tongue & Groove Slats 6 each*
A5
B1
Description
D1
1 each
D1
6” Lag Bolts
6*
E1
1-1/4” Grabber Screws
13*
* Quantities will vary depending on Door size.
All quantities in this table are for an average-size
single Door order.
A2
B2
A1
L
end view
A1
R
B1, C1
end view
tongue
end view
RH
•••••••••••••••••••••••••••••••••••••••••
All B2 Slats look like
this; a tongue and a
groove
groove
H AAssembly
NGER
HOLES
Instructions
I N S TA L L AT I O N
I N S T RU C T I O N S
5”
5”
9”
RH
•••••••••••••••••••••••••••••••••••••••••
H AAssembly
NGER
HOLES
Instructions
I N S TA L L AT I O N
Ass e m b l i n g Your D oor
PLEASE NOTE: These instructions are specific to a particular door size and
type. Adjustments may be needed on your part for changes in specifications
and measurements, as well as door types that are different from these.
We recommend a dry assembly. It is
recommended you not use glue or
adhesive of any kind.
1.
I N S T RU C T I O N S
Slide A2 over so its tongue inserts into A1R’s groove.
2. Slide B1, B2, and B3 slats to the right and down so their tongues
go into A1 R and A2’s grooves.
A4
A1
R
A1
L
A3
A1
R
B1 B2 B2
A2
A2
3.
Slide all remaining B slats into place.
Now slide A3 Middle Rail down so
the groove along the bottom covers
the tops of the B Slats.
A4
A1
R
A1
L
A3
B1
B2 B2
A2
RH
•••••••••••••••••••••••••••••••••••••••••
H AAssembly
NGER
HOLES
Instructions
I N S TA L L AT I O N
I N S T RU C T I O N S
A4
4. Slide all C Slats into A1 R Stile and A3’s top groove. Once
all of the slats have been positioned, place the A4 Top Rail
onto the C slats and in the A1 R grooves.
A1
R
A1
L
C1 C2C2C2 C2 C2C2 C3
A3
A2
At this point it will be helpful to have someone help by holding
your stiles, slats and rails firmly in place while you are installing
the Lag Bolts.
6. When the Door is as-
5. Slide Side Stile A1 L into place. You can now install the 6” Lag
sembled, place A5, A6 and
A7 (Diagonal Rails) onto
the door so the predrilled
holes are facing up and so
they form an X that runs
from corner to corner.
Attach using the 1-1/4”
Grabber Screws and a drill
with a Phillips bit. Your
Door is ready to hang.
Bolts, making sure your door remains straight. Tighten by hand,
and if all slats are correctly in place, tighten with a ratchet with a
7/16” socket.
7/16”
A1
L
RH
•••••••••••••••••••••••••••••••••••••••••