Low Rise Crib Assembly Instructions

Low Rise Crib Assembly Instructions
This page lists the contents included in
the box. Please take time to identify the
hardware as well as the individual components of the product. As you unpack
and prepare for assembly, place the
contents on a carpeted or padded area to
protect them from damage. Please
follow the assembly instructions closely.
Improper assembly can result in personal
or property damage.
Note: 2 adults are required to safely
assemble this product.
!
16 - Decorative Bolts (50mm)
4 - Hex Bolts
2 - Headboard
Panels
16 - Lock Washers
NOTE: DO NOT USE
POWER TOOLS
2 - Side
Panels
1 - Allen Wrench
1 - Mattress
Support
2 - Bases
1 - Toddler rail
(sold separately)
1 - Hex Wrench
Made in USA - r05
Page 1 of 6
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: (800) 933-9904 • e: [email protected] • www.landofnod.com
Low Rise Crib Assembly Instructions
!
1
2
Mount one side panel to the rear posts of the headboard panels. Use 4 decorative bolts and 4 lock washers to LOOSELY fasten the side panel to the headboard
posts. DO NOT tighten the bolts until instructed in step 3.
Install the mattress support in the crib with the flat side up. Extend the mounting
flange on each corner and attach the spring to headboard and footboard at the
desired level using 4 hex bolts and hex wrench provided. The top position is
recommended for newborns. The bottom position must be used when the baby
is able to kneel or stand in the crib.
Made in USA - r05
Page 2 of 6
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: (800) 933-9904 • e: [email protected] • www.landofnod.com
Low Rise Crib Assembly Instructions
Mount the remaining side panel to the posts of the headboards.
Use 4 decorative bolts and 4 lock washers to fasten the side panel
to the posts. At this point fully tighten all bolts, taking care not to
apply excessive force, using the allen wrench provided.
3
!
4
With assistance of another adult, flip the assembly upside
down. Attach the 2 bases with 8 decorative bolts and 8 lock
washers, securing all bolts with the allen wrench.
Assembly is now complete.
Made in USA - r05
Page 3 of 6
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: (800) 933-9904 • e: [email protected] • www.landofnod.com
Low Rise Crib Assembly Instructions
ASSEMBLY NOTES & TIPS
Bolts – DO NOT FORCE
If there is resistance when you are starting a bolt, back it out and try again. Sometimes there is machining
debris in between the threads that impedes the bolt from going into the insert, but it can usually be cleared by
gently re-starting the bolt. It may take more than one try. Forcing the bolt into the thread when there is
resistance may compromise the strength/integrity of the threaded insert. Once it is lined up straight, most
bolts will turn smoothly. The threaded inserts do have “teeth” that grip into the wooden hole, but if too much
force is applied (e.g. trying to overtighten or forcing it when the threads are not aligned), they will strip the
wood and spin in the hole.
Plastic Pouch – DO NOT REMOVE
Plastic Pouch (empty clear zip-lock bag) attached to the mattress support should NOT be removed. This is
provided by law for storage of the assembly instructions for future referral. Leave that bag in place.
5
Labels – DO NOT REMOVE
ALL labels on cribs are required to be in their particular locations by federal law, and should NEVER be
removed, not even by the consumer. The Federal Regulations require that the labels be indelible, and trying to
remove them will cause harm to the finish.
CONVERSION TO TODDLER BED
THIS CRIB MAY NOT BE USED AS A TODDLER
BED WITHOUT A TODDLER RAIL.
Mattress should be in lowest position. Remove one
side panel by unscrewing the 4 decorative bolts
and lock washers that fasten it to the headboard
panels, and the 2 bolts and washers that attach it
to the leg frames. Be sure to loosen all the other
decorative bolts before attempting to remove the
side panel. Once removed, attach toddler rail (sold
separately) using the same holes and all 6 of the
decorative bolts and lock washers you just
removed. Retighten all remaining decorative bolts
with the allen wrench.
6
For Toddler Bed use, the minimum age shall be no
less than 15 months and the maximum weight shall
not be greater than 50 lb (22.7kg). The mattress
intended for use on the bed shall be a full-size crib
mattress having minimum dimensions of 51-5/8 in.
(1310mm) in length and 27-1/4 in. (690mm) in width
and thickness of no less than 4 in. (100mm) and not
exceeding 6 inches (150mm).
toddler rail
(sold separately)
Made in USA - r05
Page 4 of 6
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: (800) 933-9904 • e: [email protected] • www.landofnod.com
Low Rise Crib Assembly Instructions
!
WARNING:
- Failure to follow these warnings and assembly instructions could result in serious injury or
death.
- Read all instructions before assembling crib. Keep instructions for future use.
WARNING:
!
-Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional
padding under an infant.
-To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to
sleep, unless otherwise advised by your physician.
Strangulation Hazard:
- Strings can cause strangulation! DO NOT place items with a string, cord or ribbon around a
child’s neck, such as hood strings or pacifier cords. DO NOT suspend strings over crib or toddler
bed, or attach strings to toys for any reason.
-To help prevent strangulation, tighten all fasteners. A child can trap parts of the body or clothing on loose fasteners.
- DO NOT place crib or toddler bed near windows where cords from blinds or drapes may
strangle a child.
Fall Hazard:
- When child is able to pull to standing position, set mattress to lowest position and remove
bumper pads, large toys and other objects that could serve as steps for climbing out.
-When child is able to climb out or reaches the height of 35 inches (90 cm), the crib shall no
longer be used and the child should be placed in a youth or regular bed.
!
CAUTION:
Any mattress used in this crib must be at least 27-1/4 inches (69 cm) by 51-5/8 inches (131 cm)
with a thickness no less than 4 inches (11 cm) and not exceeding 6 inches (15 cm).
- Check this product for damaged hardware, loose joints, missing parts or sharp edges before
and after assembly and frequently during use. Securely tighten loose bolts and other fasteners.
DO NOT use crib if any parts are missing, damaged, or broken.
Contact The Land of Nod® for replacement parts and instructional literature if needed.
DO NOT substitute parts.
-If refinishing, use a non-toxic finish specified for children’s products.
- Never use plastic shipping bags or other plastic film as mattress covers because they can cause
suffocation.
- Infants can suffocate in gaps between crib sides and a mattress that is too small.
- Periodically check to see that all bolts are securely tightened.
- To clean crib: wipe with clean soft cloth dampened with mild cleanser and water. Rinse with
clean water using a soft cloth, and dry thoroughly.
- Follow warnings on all products in a crib.
- When a vaporizer is in use, always aim vapor steam away from crib as well as away from any
other wood furniture.
Made in USA - r05
Page 5 of 6
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: (800) 933-9904 • e: [email protected] • www.landofnod.com
Low Rise Crib Assembly Instructions
Once the crib is in use, periodically check to make sure all bolts are tight, and tighten as
necessary. For future use, keep these instructions in the plastic bag attached to the mattress support spring.
MAINTENANCE
Upon completion of assembly be sure all screws, bolts and fastening devices have been
tightened securely. Periodically repeat this check to make sure all screws, bolts and fastening devices are tight. Before each usage or assembly, inspect crib for damaged hardware,
loose joints, missing parts or sharp edges. DO NOT use crib if parts are missing or broken.
DO NOT substitute parts. DO NOT make any alteration to this crib.
CLEANING
Mix together a mild solution of gentle dishwashing liquid and water, apply to crib surface
using a soft clean cloth lightly dampened in the solution. Rinse with clean water again
using a soft clean cloth, then dry all surfaces thoroughly with a soft dry cloth. NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL OR COARSE RAGS SHOULD BE USED TO
CLEAN THIS FINE FURNITURE.
STORAGE
A plastic pouch is attached to the crib for the storage of the assembly directions for future
referral. After completing the assembly process you are advised to read and beware of all
WARNINGS, CAUTIONS, CLEANING, STORAGE, USE AND MAINTENANCE notices contained
in these instructions. We caution you not to place excess hardware in the plastic pouch as
it could present danger to a child if retrieved and it could also puncture the crib mattress.
For long term storage of the crib, store in a cool, dry place and keep away from moisture
and extreme temperature changes.
Made in USA - r05
Page 6 of 6
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: (800) 933-9904 • e: [email protected] • www.landofnod.com