catalog CORE

Transcription

catalog CORE

2010
PETROPHYSICS
VINCI TECHNOLOGIES
CATALOGUE OF PRODUCTS
PETROPHYSICS
Core preparation
Routine core analysis
Special core analysis
Components
LIST OF INSTRUMENTS
PETROPHYSICS
CORE PREPARATION ______________________________________ 6
PLUGGING MACHINE __________________________________________________________ 7
RADIAL CORE SLABBING SAW ___________________________________________________ 8
AUTOMATIC SLABBING SAW ____________________________________________________ 9
CORE CUTTING SAW __________________________________________________________ 10
TRIMMING SAW _____________________________________________________________ 11
ENDFACE GRINDER __________________________________________________________ 12
TRIMMING / ENDFACE GRINDER ________________________________________________ 13
CENTRIFUGAL EXTRACTOR ____________________________________________________ 14
CO2 SOLVENT CORE CLEANER (CSC 70)__________________________________________ 15
SOXHLET EXTRACTOR ________________________________________________________ 16
FLOW THROUGH CORE CLEANER ________________________________________________ 17
RECOVERY STILL FOR SOLVENT_________________________________________________ 18
HUMIDITY DRYING OVEN ______________________________________________________ 19
VACUUM DRYING OVEN _______________________________________________________ 20
AIR FORCED DRYING OVEN ____________________________________________________ 21
HEATED VACUUM DESSICATOR _________________________________________________ 22
MANUAL SATURATOR ________________________________________________________ 23
AUTOMATED SATURATOR _____________________________________________________ 24
CORE DESAGREGATOR ________________________________________________________ 25
STEREOMICROSCOPE _________________________________________________________ 26
ULTRA VIOLET BOX __________________________________________________________ 27
CORE PRESERVATION KIT _____________________________________________________ 28
ROUTINE CORE ANALYSIS ________________________________ 29
HIGH PRECISION DIGITAL BALANCES _____________________________________________
DEAN STARK EXTRACTOR _____________________________________________________
RETORT OVEN ______________________________________________________________
GAMMA RAY LOGGER (NGR 200) _______________________________________________
GEOMETRIC BULK VOLUME METER (GBV) _______________________________________
IMMERSED BULK VOLUME METER (IBV) _________________________________________
MERCURY POROMETER _______________________________________________________
HELIUM POROSIMETER (HEP) __________________________________________________
HELIUM POROSIMETER FOR EDUCATIONAL PURPOSES (HEP-E) ________________________
STEADY STATE GAS PERMEAMETER (GASPERM) ____________________________________
STEADY STATE GAS PERMEAMETER FOR EDUCATIONAL PURPOSES (GPE30) ______________
WHOLE CORE STEADY STATE GAS PERMEAMETER (WHOLEPERM) ______________________
STEADY STATE GAS PERMEAMETER AND POROSIMETER (POROPERM)___________________
VINCI TECHNOLOGIES
Parc de l'Ile, 27B rue du Port, 92022 NANTERRE
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
e-mail: [email protected]
http://www.vinci-technologies.com
3/99
30
31
32
33
34
35
36
37
38
39
40
41
42
STEADY STATE GAS PERMEAMETER AND POROSIMETER FOR EDUCATIONAL PURPOSE
(POROPERM - E) _____________________________________________________________ 43
CALIBRATED PERMEABILITY CHECK PLUGS _______________________________________ 44
UNSTEADY STATE GAS PERMEAMETER AND POROSIMETER AT MODERATE CONFINING
PRESSURE (COREVAL 30) ______________________________________________________ 45
UNSTEADY STATE GAS PERMEAMETER AND POROSIMETER AT OVERBURDEN PRESSURE
(COREVAL 700) _____________________________________________________________ 46
PETROPHYSICS
AUTOMATED SAMPLE LOADING UNSTEADY STATE PERMEAMETER AND POROSIMETER AT
OVERBURDEN PRESSURE (KEYPHI)_______________________________________________ 47
LIQUID PERMEAMETER (LIQPERM) ______________________________________________ 48
BENCH TOP PERMEABILITY SYSTEM (BPS 350) ____________________________________ 49
BENCH TOP UNSTEADY STATE RELATIVE PERMEAMETER (BRP 350) ___________________ 50
BENCH TOP UNSTEADY & STEADY STATE LIQUID – LIQUID RELATIVE PERMEAMETER (SRP
350) ______________________________________________________________________ 51
ELECTRICAL PROPERTIES SYSTEM @ AMBIENT CONDITIONS (EPS-A) __________________ 52
ELECTRICAL PROPERTIES SYSTEM @ OVERBURDEN PRESSURE (EPS 700)________________ 53
CAPILLARY PRESSURE DESATURATION CELL ______________________________________ 54
CAPILLARY PRESSURE REFRIGERATED CENTRIFUGE (RC3000) ________________________ 55
CAPILLARY PRESSURE MERCURY SYSTEM (CPM 140) _______________________________ 56
DIGITAL CORE PHOTOGRAPHY SYSTEM (DCP) _____________________________________ 57
SPECIAL CORE ANALYSIS _________________________________ 58
CORE FLOOD SYSTEM FOR EOR STUDIES (CFS 700) _________________________________
UNSTEADY STATE RELATIVE PERMEAMETER (AUTOFLOOD 700) _____________________
STEADY STATE AND UNSTEADY STATE RELATIVE PERMEAMETER SYSTEM (RPS 700)_______
XRAY SCANNER FOR IN-SITU SATURATION MONITORING _____________________________
FORMATION DAMAGE AND WELL TREATMENT EVALUATION SYSTEM (FDS 350) __________
CAPILLARY PRESSURE AND RESISTIVITY INDEX SYSTEM (CAPRI) _____________________
ROCK COMPRESSIBILITY SYSTEM (RCS 700) ______________________________________
ATMOSPHERIC ACOUSTIC VELOCITY SYSTEM (AVS A) ______________________________
OVERBURDEN ACOUSTIC VELOCITY SYSTEM (AVS 700) _____________________________
AUTOMATED HP-HT ACOUSTIC VELOCITY SYSTEM (AVS 700-HT) ___________________
AGING CELL APPARATUS (ACA 700) ____________________________________________
59
60
61
62
63
64
65
66
67
68
69
COREHOLDERS __________________________________________ 70
HASSLER COREHOLDER (HAS SERIES) ____________________________________________
HYDROSTATIC COREHOLDER (HYC SERIES)________________________________________
TRIAXIAL COREHOLDER (TRC SERIES) ____________________________________________
LEAKOFF COREHOLDER (LEC SERIES) ____________________________________________
QUICK RELEASE COREHOLDER (QRC SERIES)_______________________________________
TRANSPARENT COMPOSITE COREHOLDER (TCC SERIES) ______________________________
ACOUSTIC VELOCITY COREHOLDER (AVC SERIES) __________________________________
ELECTRICAL RESISTIVITY AND CAPILLARY PRESSURE COREHOLDER (ECP SERIES) _________
HEATING SYSTEM (HES SERIES) _________________________________________________
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
4/99
71
72
73
74
75
76
77
78
79
STANDS (STA SERIES)_________________________________________________________ 80
PETROPHYSICS
CORE ANALYSIS COMPONENTS ____________________________ 81
LEVEL TRACKER SEPARATOR (LTS SERIES)________________________________________
DUAL LEVEL TRACKER (DLT SERIES) ____________________________________________
AMBIENT CONDITIONS TWO PHASE VIDEO SEPARATOR (VSE -A) ________________________
HP-HT TWO PHASE VIDEO SEPARATOR (VSE 700)____________________________________
WET GAS METER (WG SERIES) __________________________________________________
CAPILLARY SIGHT GLASS TUBE _________________________________________________
BACK PRESSURE REGULATOR (BPR) _____________________________________________
ELECTRICAL ISOLATOR (EI 700) ________________________________________________
AUTOMATED CONFINING PRESSURE CONTROLLER (ACP 700) _______________________
FLOATING PISTON ACCUMULATOR (FPA SERIES) ___________________________________
MIXER CYLINDER (MC SERIES) _________________________________________________
FLUID TRANSFER VESSELS (FTV SERIES) __________________________________________
HYDRAULIC INTENSIFIER (HI SERIES) ____________________________________________
PRESSURE GENERATOR SYSTEM (PGS) ___________________________________________
DIGITAL PRESSURE GAUGE (DPG SERIES)__________________________________________
DEADWEIGHT GAUGE_________________________________________________________
UNINTERRUPTABLE POWER SUPPLY (UPS 16) ______________________________________
OTHER COMPONENTS _________________________________________________________
The specifications and photos contained in this catalogue can be subject to change without
notification.
Copyright© Vinci Technologies. All rights reserved.
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
5/99
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
PETROPHYSICS
CORE PREPARATION
Core cutting
Core cleaning
Core drying
Core saturation
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
6/99
PLUGGING MACHINE
PETROPHYSICS
The heavy built diamond tooled drill press is especially designed to drill in various size core
samples. The standard machine comes with a floor standing drill press, a rotary union, a coolant
feeding system, a coolant recovery pan with splash guard and a core clamping vise. The union
permits to connect the coring bit to the drill press and feed coolant to the coring bit. The vise
assembly can be mounted on the pan table and allows for the positioning of the core. Various
sizes of coring bits as well as the recirculating coolant system are available.
FEATURES
Coring bit internal diameter:
Maximum coring depth:
Drip pan dimension:
Compatible coolant:
Drill speed:
Motor power:
Electrical:
Weight:
Volume:
1", 1.5", 2"
5 inches (12.5 cm)
L x W x H: 600 x 300 x 250 mm
Water, Oil
360, 520, 800, 1150, 1840, 2650, 4070, 5750 RPM
1100 watts, 1500 RPM
220 VAC 1 phase, 60 Hz
150 kg
500 x 500 x 1800 mm
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
7/99
RADIAL CORE SLABBING SAW
PETROPHYSICS
Versatile diamond impregnated radial blade utilised to slab core samples in two halves or to
trim full diameter rock samples. The standard machine comes with a worktable, blade guard,
motor to power the saw, core clamp assembly for holding core, sample trolley on ball bearing
guide, coolant feeding system , coolant recovery pan and diamond impregnated saw blade. The
recirculating coolant system is also available.
FEATURES
Saw blade diameter
Maximum cutting depth
Max core length
Compatible coolants
Power supply
Weight
400 mm (16’’) (other upon request, max 500 mm)
125 mm (5”)
300 mm, 1000 mm in option
Water and oil
220 VAC, 50 Hz, 4,000 W
320 kg
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
8/99
AUTOMATIC SLABBING SAW
PETROPHYSICS
Versatile diamond impregnated radial blade utilized to slab core samples in two halves or to
trim full diameter rock samples. The automated machine is fitted with a variable rate feed
mechanism that enables the cutting of long section of very dense core in one pass without
fracturing, grooving or chipping and producing a high-finished surface. The core sample
remains fixed, while the carriage holding the diamond disc and motor unit moves along the core
sample at an adjustable and regulated speed. The moving of the saw blade along the core sample
starts when the cutting depth is reached. The saw arm oscillates around an axis so that a
constant cut pressure is maintained whatever the hardness of the sample material encountered.
This pressure is easily adjusted while the machine is in operation.
FEATURES
Saw blade diameter
Maximum core length
Compatible coolants
Power supply
Weight
Volume
400 mm (16’’) (other diam upon request, max = 500 mm)
125 mm (5”)
1 meter
Water and oil
380 VAC 3 Phases, 50 or 60 Hz, 8,000 W
1200 kg
4000x1050x2030 mm
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
9/99
CORE CUTTING SAW
PETROPHYSICS
Versatile bench top diamond impregnated radial blade utilized to cut plug sized core samples in
two halves or to trim rock samples. The standard machine comes with a blade guard, a motor to
power the saw, a sample trolley on ball bearing guide, a shut off button, a coolant feeding
system, a coolant recovery pan and a diamond impregnated saw blade.
FEATURES
Saw blade diameter
Max core length
Compatible coolants
Power supply
Weight
Volume
350 mm (14”)
100 mm (4”)
300 mm
Water and oil
220 or 380 VAC, 50 Hz, 3 horses
82 kg
1120x620x710 mm
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
10/99
TRIMMING SAW
PETROPHYSICS
Bench top tool designed to cut preset core sample lengths. The preset sample lengths can be
adjusted at any time by rearranging machined spacers to the desired length between the blades.
The quality of the saw blade allows for extreme precision of the end face after trimming of
0.002 inch (5/100 mm). All wetted components are constructed from stainless steel and
anodized aluminium for long lasting corrosion free operation. All bearings are sealed to insure
long lasting free movement. The containment pans and splash guards are also constructed of
heavy gauge stainless steel, anodized aluminium and corrosion free plastic. Recirculating
coolant system is also available.
FEATURES
Saw blade diameter
Saw blade thickness
Core diameter
Core length
Lubricants
Power supply
Motor power
Weight
Dimension
200 mm (8’’)
2 mm
up to 2’’
2”, 3” other upon request
water (usually), oil
220 VAC 1 phase 50 or 60 Hz
550 W, 3,000 RPM
80 kg
700x800x600 mm
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
11/99
ENDFACE GRINDER
PETROPHYSICS
Tool designed to provide flat, parallel end-faces when sample geometry is critical for advanced
rock property test. The tool comes with a core clamping device, housing and cover parts, a
coolant feeding system, a coolant recovery pan and a diamond tool end-face grinding wheel. A
core clamping device for whole diameter core sample, a recirculating coolant system and
hoover for dry grinding operations are also available.
FEATURES
Core diameter
Grinding wheel precision
Wheel diameter
Power supply
Motor power
Weight
Volume
up to 2"
+/- 0.001 inch (2.5 / 100 mm)
150 mm
220 VAC 1 ph50 or 60 Hz
0,55 kW, 3,000 RPM
70 kg
600x500x500 mm
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
12/99
TRIMMING / ENDFACE GRINDER
PETROPHYSICS
Bench top tool which combines a trimming saw at one side and an endface grinder on the other
side. It is designed to cut preset core sample lengths and grind the sample with extreme
precision of the end face after trimming of 0.002 inch (5/100 mm).
FEATURES
Saw blades diameter
Saw blades thickness
Grinding precision
Grinding wheel diameter
Core diameter
Core length
Lubricants
Power supply
Motor power
Weight
Volume
200 mm (8’’)
2 mm
+/- 0.001 inch (2.5 / 100 mm)
150 mm
up to 2’’
2”, 3” other upon request
Water (usually), Oil
220 VAC 1 ph 50 / 60 Hz
550 W, 3,000 RPM
100 kg
700x800x600 mm
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
13/99
CENTRIFUGAL EXTRACTOR
PETROPHYSICS
The centrifugal extractor is designed to spray warm, clean solvent from a still against the core
samples. The centrifugal force causes solvent to flow through samples displacing and extracting
the oil (and water). The speed of rotation can be selected depending on the permeability and
degree of consolidation of the core. Most common solvents can be used. A solvent recovery still
is also provided to recycle clean and warm solvent into the centrifugal extractor in closed loop.
FEATURES
Core diameter
Core length
Quantity of sample
Wetted materials
Centrifuge speed
Electrical
up to 2"
up to 3’’
between 6 to 18 depending on the core length
Stainless steel, teflon
up to 3000 rpm
220V, 50Hz, 1500W
BENEFITS
Centrifugal Extractor :
Rapid and efficient extraction of oil, water and salt from consolidated core samples
Speed controller
Rotor geometry to accomodate the core samples
Solvent inlet and outlet
Vibration free chassis
Solvent recovery still :
Heated solvent flask
Water refrigerant for solvent condensation
Temperature controller
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
14/99
CO2 SOLVENT CORE CLEANER (CSC 70)
PETROPHYSICS
The core Cleaner is a device for cleaning crude oil, drilling mud liquids, and water from a single
piece of whole core or from a batch of core plug samples. The principle consists of filling the
gas filled space in the core with solvent (e.g. toluene) by surrounding the core with a suitable
solvent containing dissolved CO2 gas and applying sufficient hydraulic pressure. The solvent
mixes with oil in the core and subsequent depressurizing to atmospheric pressure removes
residual oil from the core. A number of repeated cycles are required to clean the core of
hydrocarbons.
The apparatus fits into a standard size floor hood. The cleaning chamber is a pressure vessel
heated electrically with a two-kilowatt, 220-volt heater enclosed in an explosion proof housing.
The solvent is pumped from an onboard supply tank to the cleaning vessel with a high pressure
pump. A cyclone separator with a stainless steel-packed, water-cooled after-cooler is provided
to separate the CO2 and the used hot solvent when the vessel is drained. The used toluene drains
into an explosion proof electric still where it is recovered and delivered back to the clean
solvent supply. The still operation is automatic. The process controls are housed in a nonexplosion proof box intended to be mounted outside of the hood.
FEATURES
Vessel diameter:
Vessel length
CO2 pressure
Solvent pressure
Wetted materials
Net weight
Requirements:
Air
Electrical
Cooling water
Model 1:4.6” (118 mm) - Model 2: 5.2” (134 mm)
Model 1:10.7” (274 mm) - Model 2: 27” (660 mm)
200 psi
1,000 psi
316 Stainless steel
200 kg
100 psi
220V, 50Hz, 2,000 Watts
8 l/m @ 14 kPa (2 gpm @ 20 psi)
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
15/99
SOXHLET EXTRACTOR
PETROPHYSICS
The soxhlet distillation extraction method is used to dissolve and extract oil and brine from rock
core sample by using solvents. The cleanliness of the sample is determined from the color of the
solvent that siphons periodically from the extractor which must be clear. The samples are
placed in the extractor and cleaned by refluxing solvent. The solvent is heated and vaporized in
boiling flasks and cooled at the top by condenser. The cooled solvent liquid falls into the sample
chamber. The cleaned solvent fills the chamber and soaks the core sample. When the chamber is
full, the dirty solvent which was used to clean the core siphons back into the boiling flask and is
redistilled again The apparatus consists of a distillation/extraction glassware unit and a heating
mantle with thermostatic controller. The glassware is composed of boiling flask, soxhlet
extractor and condenser. A flexible plastic tubing is also used to connect the condenser to the
water cooling unit. All these devices are mounted on a mounting rack.
FEATURES
SOXHLET FOR PLUG SIZED CORE SAMPLES
Configuration
Core sample diameter
Core sample length
Extractor capacity
Boiling flask
Heating temperature
Water cooling system
Single unit model/ Multiple units model (up to 6 extractors)
up to 1,5”
up to 4”
250 ml
500 ml
up to 450°C
0.5 to 3 liters per minute, 18°C
Power supply
220 VAC 50 Hz
SOXHLET FOR FULL SIZED CORE SAMPLES
Configuration
Core sample length
Extractor capacity
Boiling flask
Heating temperature
Power supply
Single unit model / Multiple units model (up to 6 extractors)
up to 4”
up to 6”
3 liters
6 liters
up to 450°C
220 VAC 50 Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
16/99
FLOW THROUGH CORE CLEANER
PETROPHYSICS
The apparatus is a rapid and efficient core cleaning system based on controlled sequential
solvent displacement under moderate pressure. Extraction of hydrocarbons and salts from
reservoir rocks is achieved by injecting one or more solvents into the core sample under
pressure and moderate temperature. The pressure used depends on the sample permeability. The
core is considered clean when the effluent is clean.
FEATURES
Maximum confining pressure
Core diameter
Core length
Fluid flow rate
Wetted parts
Electrical
Weight
1,000 psi
1.5” (other upon request)
Up to 3” (other upon request)
5 cc/min (recommended)
Stainless steel
220 VAC, 50 Hz
40 Kg
BENEFITS
Possibility to pump different solvents
Constant injection flow for solvent
Easy core loading and unloading operation
Cleaning at pressure for high permeability sample
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
17/99
RECOVERY STILL FOR SOLVENT
PETROPHYSICS
The recovery still is designed to reclaim clean solvent from dirty solvent containing a mixture of
crude oil and solvent. The recovery process is based on fractional distillation by boiling point
temperature difference between the crude oil and the solvent. The apparatus is explosion proof
and should be installed away from any area of hazardous atmosphere. It consists mainly of (a)
an insulated boiler tank equipped with heaters located at the bottom and (b) a condenser using
house water. The recovered solvent is evacuated into a container whereas the dirty toluene is
transferred manually into the tank. The plastic bag located in the tank in which the dirty solvent
is poured permits to facilitate the evacuation of sludge deposit after the recovery process.
FEATURES
Recovery
Recovery time
Max temperature
Tank capacity
Protection
Material
House water consumption
Power supply
Dimensions
Weight
95 %
3 to 5 hours for 20 litres
200°C
20 litres, other upon request
IP 66
stainless steel
50 litres per hour
220 VAC 50 Hz , 2,500 W
850x1000x1000 mm
165 Kg
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
18/99
HUMIDITY DRYING OVEN
PETROPHYSICS
The humidity drying oven is used to dry core samples under constant relative humidity
condition; in particular it is very important when the core contains hydratable clays or gypsum.
This oven is composed of a robust air bath, an electronic temperature regulator, a water vapor
injection system, a capacitance probe to control humidity level and a timer.
FEATURES
Capacity
Humidity range
Temperature
Humidity stability
Temperature stability
Internal dimensions
Power supply
Weight
Water consumption
240 liters
10% to 90%
+10°C + 90°C
+/- 1%
+/- 0.1 °C
800 x 500 x 600 mm
220V / 50Hz , 2500 W
184 kg
1 – 10 bar (200 – 500 µS/cm)
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
19/99
VACUUM DRYING OVEN
PETROPHYSICS
The vacuum drying oven enables fast drying of core under vacuum. This oven is composed of a
robust vacuum air bath, an electronic temperature regulator and digital vacuum control through
solenoid valves. Two sizes can be selected.
FEATURES
MODEL 1: 49 LITRES VACUUM OVEN
Capacity
Temperature
Vacuum
Internal dimensions
Power supply
Weight
49 liters
20 to 200°C
10 mb to 1100 mb, accur 1 mbar
385 x 330 x 385 mm
220V, 50Hz, 2000 W
82 kg
MODEL 2: 101 LITRES VACUUM OVEN
Capacity
Temperature
Vacuum
Internal dimensions
Power supply
Weight
101 liters
20 to 200°C
10 mb to 1100 mb, accur 1 mbar
545 x 400 x 465 mm
220V, 50Hz , 2400 W
120 kg
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
20/99
AIR FORCED DRYING OVEN
PETROPHYSICS
The air forced drying oven enables efficient drying of core samples after cleaning with solvents
before permeability or porosity measurements. This oven is composed of a robust air forced
convection air bath, a variable speed turbine, an electronic temperature regulator and a timer .
Two sizes are available.
FEATURES
53 LITERS MODEL
Capacity ……………………. 53 liters
Temperature ………………… 220°C
Internal dimensions…………..400 x 330 x 400 mm
Power supply ……………….220V , 50Hz , 2,000 W
Weight ……………………….42 kg
108 LITERS MODEL
Capacity ……………………. 108 liters
Temperature ………………... 220°C
Internal dimensions…………. 556 x 400 x 480mm
Power supply………………… 220V , 50Hz , 2,000 W
Weight ………………………63 kg
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
21/99
HEATED VACUUM DESSICATOR
PETROPHYSICS
The vacuum heated dessicator is designed especially to dry a bunch of core samples under
vacuum. This operation is required to remove humidity of core samples before gas permeability
or porosity measurements. The system includes an heated dessicator and a vacuum pump. The
dessicator includes a machined stainless steel heating plate with a glass bell, designed to
withstand the pressure difference between in and outside. The sealing is secured by a viton Oring between the heating plate and the bell. The samples are dried by direct contact with the
heating plate. The small volume and the compact design guarantee a short heating time. It is
easy and safe to operate, requires hardly any maintenance, and visibility is perfect.
FEATURES
Temperature………………… up to 80°C
Vacuum... …...……………… 10 -3 mbar
Max pumping speed………… 2.5 m3/h
Quantity of sample…………… around 30
Material ………………………..stainless steel 316L
Electrical …………………….. 220V, 50Hz,
BENEFITS
Rapid and efficient drying
Total visibility on the product to be dried
Compact
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
22/99
MANUAL SATURATOR
PETROPHYSICS
The manual saturator permits to perform a sequence of vacuum and saturation cycles on plug
size samples. The standard apparatus includes a plug sized core cell, a vacuum pump, an hand
operated pressure pump (2,000 psi output), a saturant vacuum tank and necessary hand operated
valves and plumbing. A larger capacity cell to accommodate full size core samples is also
available.
FEATURES
Max saturating pressure
2,000 psi
Cell diameter
Cell height
Wetted materials
58 mm
300 mm
316 Stainless steel (other on request)
Saturant
water, brine, oil or other liquids
BENEFITS
Rapid and efficient saturation
Can accomodate plug size sample and full sized core sample in option
Manual operations
Loading carrier for easy loading
Dead volume sets to minimize volume of saturant
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
23/99
AUTOMATED SATURATOR
PETROPHYSICS
The automated saturator permits to perform a sequence of vacuum, filling and saturation cycles
on plug size samples in an automated mode to free the operator for other tasks. The bench top
apparatus comes with a plug sized core cell, a vacuum pump, a high pressure liquid pump
(2,000 psi output), a saturant vacuum tank and necessary automated valves and plumbing. A
larger capacity cell to accommodate full size core samples is also available. The apparatus is
controlled by a touch screen panel PC which allows the operator to open or close the valves,
start and stop the high pressure pump, the vacuum pump and to run automatic saturation cycles.
FEATURES
Max saturating pressure
2,000 psi
Cell diameter
Cell height
Wetted materials
58 mm
300 mm
316 Stainless steel (other on request)
Saturant
Power supply
water, brine, oil or other liquids
220 VAC, 50 Hz
BENEFITS
Rapid and efficient saturation
Can accomodate plug sized sample and full sized core sample
Fully automated operations
Loading carrier for easy loading
Dead volume sets to minimize volume of saturant
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
24/99
CORE DESAGREGATOR
PETROPHYSICS
Designed to pulverize core samples into a small granular texture to be loaded in the sample
chamber. The sample is crushed under high pressure between two crushing plates in an enclosed
chamber.
FEATURES
Crushing type
Feed size
Initial core size
Final particle size
Capacity
Power supply
Dimensions
Net weight
by pressure
65 x 65 mm
60 mm
1 to 15 mm
up to 200 kg/h
220 or 380 VAC , 50 Hz , 1,100 W
410 x 830 x 720 mm
177 Kg
BENEFITS
Adaptable crushing geometry
10 stage gap setting adjustment
Crushing plates easily accessed and replaced
Not accessible, moving part fully interlocked casing
Very fast, uniform comminution
Almost loss free grinding
Closed grinding chamber with extraction part for dust free operations
Easy cleaning, minimum contamination between samples
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
25/99
STEREOMICROSCOPE
PETROPHYSICS
The Stereomicroscope Stemi 2000 meets your demands in two respects.
On the one hand it offers the low-price advantage common with Greenough-type instruments,
on the other hand it features a performance that will surely surprise you. The extremely wide
7.7:1 zoom range (pancratic system 0.65x...5.0x) zooms them in as hardly any other
stereomicroscope of this class can do. It includes a cold light source.
FEATURES
Model
Magnification
Viewing field
Working distance
Power supply
ZEISS STEMI 2000
x6.5 …x50
Max 23mm
90 mm
220 VAC 50Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
26/99
ULTRA VIOLET BOX
PETROPHYSICS
The ultra violet box is composed of a ultra violet light tube and a fluorescent white light to
enable observation of core and cutting samples under both UV light and white light. An access
permits to introduce the sample inside the box without introducing exterior light.
FEATURES:
Light
Power supply
UV and white fluorescent light
220 VAC 50Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
27/99
CORE PRESERVATION KIT
PETROPHYSICS
The core preservation kit provides the components necessary for the core preservation
technique. It consists of wrapping the core sample in several layers of high quality plastic film
to prevent puncturing and then wrapped it again with several layers of aluminum foil, with the
free ends crimped together. A wire is tied around the core to make a handle. The foil-wrapped
core sample is then dipped in a molten wax coating material for mechanical stabilization. The
prepared core is then introduced in a heat sealed plastic bag for transportation.
FEATURES:
Roll of high quality plastic film
Roll of aluminium film
Roll of wire
Melting pot for wax coating
Wax coating
Cooling rack
Heat sealer
Bag film kit
Bags
Glue
Shovel
Pair of gloves
Labelling facilities
Grabs and scissors
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
28/99
PETROPHYSICS
ROUTINE CORE ANALYSIS
Capillary pressure
Coreval 30
Electrical Properties System
BRP 350
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
29/99
HIGH PRECISION DIGITAL BALANCES
PETROPHYSICS
Digital balances especially selected for core applications where measurement accuracy is
required.
FEATURES
TYPICAL BALANCE FOR PLUG SIZED CORE SAMPLES
Weighing range
Accuracy
Power supply
0-620 g, other upon request
0.001 g
220 VAC 50 Hz
TYPICAL BALANCE FOR FULL SIZED CORE SAMPLES
Weighing range
Accuracy
Power supply
6,200 g, other upon request
0.01 g
220 VAC 50 Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
30/99
DEAN STARK EXTRACTOR
PETROPHYSICS
The dean stark extractor is used to determine fluid saturation of core samples. The sample is
first weighed and then introduced into the dean stark extractor. The water fraction is vaporized
by boiling solvent, condensed and then collected in a calibrated receiver. Vaporized solvent also
condenses, soaks the sample, and extracts the oil. The sample is then oven dried and weighed.
The oil content is determined by gravimetric difference while the water content is
volumetrically measured by the receiving tube. The apparatus consists of a
distillation/extraction glassware unit and a heating mantle with thermostatic controller. The
glassware is composed of boiling flask with extractor, a sample support screen, volumetrically
graduated water receiving tube, condenser and desiccant drying tube. A flexible plastic tubing is
also used to connect the condenser to the water cooling unit. All these devices are mounted on a
mounting rack
FEATURES
DEAN STARK FOR PLUG CORE SAMPLE
Configuration
Core sample length
Extractor capacity
Boiling flask
Receiving tube
Heating temperature
Power supply
up to 1.5”
up to 4”
250 ml
500 ml
5 & 10 ml, 0.1 ml graduation
up to 450°C
220 VAC 50 HZ
DEAN STARK FOR FULL SIZE CORE SAMPLE
Configuration
Core sample length
Extractor capacity
Boiling flask
Receiving tube
Heating temperature
Power supply
up to 4”
up to 6”
3 liters
6 liters
40 ml, 0.2 ml graduation with drain valve
up to 450°C
220 VAC 50 Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
31/99
RETORT OVEN
PETROPHYSICS
The retort oven is designed to determine oil and water fluid saturation by a high temperature
retorting process in which the oil and water contained in a fresh sample of crushed core material
are vaporized, condensed and collected in calibrated glassware. The samples are progressively
heated to remove water and then heat up to 650°C (1,200°F) to remove oil from the sample. The
gas saturation is determined on an adjacent, litho logically similar sample by placing the core
sample in a mercury porosimeter and measuring the amount of mercury injected with the water
and/or oil in place. The system comprises a retort cabinet containing two chambers of five
sample bombs capable of holding crushed core material. Each bomb is equipped with a sealed
threaded cap and is connected to a long, stainless steel condensing tube. The tube passes
through a water bath thereby enhancing condensation of the evolved gases. Calibrated glass
receiving tube is affixed to each condensing tube with a rubber stopper to collect the water and
oil produced from the sample.
FEATURES
Sample bomb capacity
Receiving tube capacity
Number of sample bomb / receiving tub
Max Temperature
Material
Weight
Dimensions
Electrical
100 grams of crushed core material
20 ml (other size upon request)
10
650°C (1,200 °F)
carbon refractory steel
50 kg
1150 x 915 x 535 mm (45 x 36 x 21 in)
220V, 50Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
32/99
GAMMA RAY LOGGER (NGR 200)
PETROPHYSICS
The NGR200 core gamma ray logger provides both total and spectral analysis of the natural
gamma radiations emitted from the core samples upon arrival at the laboratory. It permits to
differentiate uranium, thorium and potassium concentrations. The data obtained with this
apparatus can be used to adjust the depth of the core to coincide with the open-hole logging
depths and to identify zones where core has been lost. The apparatus consists of a conveyer for
moving core, lead shielding to reduce background gamma radiation and a suitable gamma ray
detector. The detector system consists of a shielded scintillation crystal coupled with a photo
multiplier. Signals from the detector are processed using a multi channel spectrum analyzer and
analytical software. The gamma ray events are energy - sorted and counted over three energy
windows K, U and Th as well as the total gamma radiation. Core samples can be in barrel, in a
fibre glass, or aluminium, liner or exposed. The core is scanned along its length from bottom to
top simulating a wire-line log pass. The logging speed is adjustable to suit the core and data
requirements.
FEATURES
Belt length
Suitable for core
Shielding area
Sodium Iodine detector
Variable logging speed
Power supply
3 meters
up to 5.5’’
5 & 3.7 cm around the crystal
3” by 3”
up to 5 feet / min
230 VAC 50/60 Hz 1 phase
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
33/99
GEOMETRIC BULK VOLUME METER (GBV)
PETROPHYSICS
This instrument is designed to measure bulk volume of plug sized and/or full diameter core
samples with excellent accuracy. The principle consists of measuring accurately the length and
diameter of the samples at different grades. Minimum of 8 measurements along the diameter
and one every 50 mm along the length are necessary to get an accurate bulk volume
measurement. The bulk volume is determined by integrating those measurements. This
calculation can be done by hand or by optional computer program. In the latest, calipered
dimensional data on core samples are automatically logged and the geometric bulk volume,
shape factor, effective flow area and caliper bulk factor are automatically calculated by the
program.
FEATURES
A digital 150 mm caliper for plug cores with accuracy of +/- 0.02 mm
A digital 300 mm caliper for full diameter cores with accuracy of +/- 0.02 mm
A software to calculate the bulk volume parameters.
Electrical: 220V, 50Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
34/99
IMMERSED BULK VOLUME METER (IBV)
PETROPHYSICS
The immersed bulk volume determination system is designed to measure bulk volume of plug
sized core samples with excellent accuracy. The principle consists of immersing the core sample
under mercury and measuring with a high precision weighing balance the resulting buoyant
force. The bulk volume is then determined by using the Archimede principle.
FEATURES
A robust base which supports the balance and a vertical post
An adjustable immersion depth and precision ram with level mark
A cradle which supports the sample when it is immerged in the mercury
A high precision balance with RS232 communication port
Reading accuracy: 0.01 g
Max weighing: 6,200 g
Repeatability: +/- 0.01 g
Linearity: +/- 0.01 g
A thermometer for mercury density determination
Mercury immersion bath
Electrical: 220V, 50Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
35/99
MERCURY POROMETER
PETROPHYSICS
Tool designed to measure the gas space and bulk volume of a freshly recovered core sample.
The instrument consists of a hand operated pump, a sample cell equipped with a needle valve
mounted on its lid. The cell can accommodate a sample with a bulk volume of 10 to 15 cm3.
The mercury pump is equipped with a vernier calliper graduated in 0.01 cm3 increments. A
pressure gauge capable of indicating pressure up to 100 bar and a vacuum gauge are connected
to the system.
FEATURES
Max pressure
Sample volume
Cell size
Pump volume
Direct reading by vernier
Wetted part
100 bar (1,500 psi)
10 to 15 cc
40 x 70 mm
100 cc
0.01 cm3
Stainless steel
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
36/99
HELIUM POROSIMETER (HEP)
PETROPHYSICS
The Helium gas expansion porosimeter is based on the Boyle’s and Charles’ law expansion of
helium gas and is used for direct grain volume and pore volume measurement in auxiliary cell at
isothermal conditions. Subsequently, porosity and grain density can be derived from the direct
measurements. A data acquisition computer allows for data logging and calculation of
parameters and also calibration data. The instrument measures grain volume of plug samples of
1” and 1.5” diameter. An optional full diameter matrix cup can be added for determination of
grain volume of whole diameter core samples. Each sample matrix cup is interchangeable and is
provided with stainless steel calibration check plugs. An auxiliary core holder for plug and
whole diameter core samples can also be used to measure pore volume at ambient or overburden
pressure.
FEATURES
Core diameter:
Core length:
Porosity Range:
Charge Pressure in reference volume:
Pressure sensor accuracy:
Porosity Range:
Electrical requirements:
N2/Helium requirements:
Dry air requirements:
1” and 1.5”, (4” optional)
up to 3”, (up to 12” optional)
up to 60%
200 psi
0.1%
up to 60%
220 VAC, 50 Hz
500 psi
100 psi
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
37/99
HELIUM POROSIMETER FOR EDUCATIONAL PURPOSES
(HEP-E)
PETROPHYSICS
The Helium gas expansion porosimeter is based on the Boyle’s and Charles’ law expansion of
helium gas and is used for direct grain volume and pore volume measurement in auxiliary cell at
isothermal conditions. Subsequently, porosity and grain density can be derived from the direct
measurements. An excel spreadsheet calculation template allows for calculation of grain volume
and porosity.
FEATURES
Core diameter
Core length
Porosity Range
Charge Pressure in reference volume
Pressure sensor accuracy
Porosity Range
Electrical requirements
N2/Helium requirements
1” and 1.5”
up to 3"
up to 60%
200 psi
0.1%
up to 60%
220 VAC, 50 Hz
500 psi
BENEFITS
Cost effective
Ideal for educational purposes
Compact system
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
38/99
STEADY STATE GAS PERMEAMETER (GASPERM)
PETROPHYSICS
The Gasperm instrument is dedicated to measure permeability to gas (air, nitrogen ...) of plug
sized core samples at room conditions and reservoir overburden pressure using the steady state
method. The instrument is designed for the injection of gas through the test sample at various
conditions of pressure and flow rates. The injection pressure at the core face is measured using a
pressure transducer and the gas flow rate is measured using one of the two precision mass flow
meters. The permeameter console can be configured with a precision pressure control valve to
vary the differential pressure and gas flow in the core which allows for the determination of slip
factor and Klinkenberg permeability versus reciprocal mean pressure relationship.
FEATURES
Permeability Range
Flow Pressure
Gas flow
Temperature
Temperature accuracy
Pressure transducer accuracy
Diff. pressure transducer accuracy
Flow accuracy
Nitrogen supply
Power
0.01md to 10 darcies
0 to 100 psi
0-50, 0-2,000 cc/min
ambient
+/- 0.1 °C
0.1% F.S.
0.25% F.S.
1 % F.S.
250 psi
220 VAC, 50 Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
39/99
STEADY STATE GAS PERMEAMETER FOR EDUCATIONAL
PURPOSES (GPE30)
PETROPHYSICS
The educational gasperm instrument is dedicated to measure permeability to gas (air,
nitrogen,..) of plug sized core samples at room conditions and reservoir overburden pressure
using the steady state method. The instrument is designed for the injection of gas through the
test sample at various conditions of pressure and flow rates. The injection pressure at the core
face is measured using a pressure transducer and the gas flow rate is measured using a precision
mass flow metes. An excel spreadsheet calculation template allows for calculation of gas
permeability.
FEATURES
Permeability Range
Flow Pressure
Gas flow
Temperature
Flow accuracy
Nitrogen supply
Power
1md to 1 darcy
0 to 30 psi
0-500 cc/min
ambient
+/- 0.1 °C
0.1% F.S.
1 % F.S.
250 psi
220 VAC, 50 Hz
BENEFITS
Cost effective
Compact system
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
40/99
WHOLE CORE STEADY STATE GAS PERMEAMETER
(WHOLEPERM)
PETROPHYSICS
The wholeperm instrument is dedicated to measure horizontal and vertical permeability to gas
(air, helium, nitrogen,..) of full size core samples at room conditions. The instrument is provided
with a gas permeameter console, a full size coreholder and a data acquisition computer station.
The air permeability determination is based on the steady state method. The instrument is
designed for the injection of gas through the test sample at various conditions of pressure and
flow rates. The injection pressure at the core face is measured using a pressure transducer and
the gas flow rate is measured using one of the two precision mass flow meters. The
permeameter console features a precision pressure metering valve to vary the pressure
differential and gas flow in the core which allows for the determination of slip factor and
Klinkenberg permeability versus reciprocal mean pressure relationship.
FEATURES
Permeability Range
Flow Pressure
Confining Pressure
Gas flow
Temperature
Diff. Pressure transducer accuracy
Flow accuracy
Core diameter
Core length
0. 01md to 10 darcies
0 - 100 psi
0 - 400 psi
0-50 and 0-2,000 cc/min
ambient
+/- 0.1 °C
0.1% F.S.
0.25% F.S.
1 % F.S.
4” (other upon request)
3 to 6” (other upon request)
BENEFITS
Fast loading and unloading operation
Wide range of core diameter
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
41/99
STEADY STATE GAS PERMEAMETER AND POROSIMETER
(POROPERM)
PETROPHYSICS
The poroperm instrument is dedicated to measure steady state gas permeability, klinkenberg
permeability, pore volume and grain volume of plug sized core samples at room conditions. The
instrument is provided with a permeameter console, an hassler coreholder, a matrix cup and a
data acquisition computer station to be operated in manual and automatic mode. An optional
hydrostatic coreholder can be used to perform measurement at overburden pressure.
FEATURES
Permeability Range:
Flow Pressure:
Confining Pressure:
0 - 200 psi
0 - 400 psi
(option 10,000 psi)
0-50 and 0-2,000 cc/min
Gas flow:
Temperature:
Ambient
Pressure transducer accuracy:
0.1% F.S.
Diff. Pressure transducer accuracy: 0.25% F.S.
Flow accuracy:
1 % F.S.
Core diameter:
1” and 1.5” (option)
Core length:
Up to 3”
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
42/99
STEADY STATE GAS PERMEAMETER AND POROSIMETER
FOR EDUCATIONAL PURPOSE (POROPERM - E)
PETROPHYSICS
The educational poroperm instrument is dedicated to measure steady state gas permeability and
porosity of plug sized core samples at room conditions. The instrument is provided with a
permeameter console, an hassler coreholder, a matrix cup and a data acquisition computer
station to be operated in manual and automatic mode.
FEATURES
Permeability Range:
Flow Pressure:
Confining Pressure:
Gas flow:
Temperature:
Pressure transducer accuracy:
Flow accuracy:
Core diameter:
Core length:
0.5 md to 5 darcies
0 - 100 psi
0 - 400 psi
0-500 cc/min
Ambient
0.1% F.S.
1 % F.S.
1” and 1.5” (option)
Up to 3”
BENEFITS
Cost effective
Compact system
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
43/99
CALIBRATED PERMEABILITY CHECK PLUGS
PETROPHYSICS
The check plugs are used to check and test the calibration of gas permeameters. The set consists
of five stainless steel check plugs with different permeability to air. The plug is made of a shell
that protects the porous media. These calibration plugs are not primary standards and have been
tested using customary testing methods.
FEATURES
Diameter
Length
Permeability range
Porosity range
1.0 inch, 1.5 inch, 30 mm, 50 mm (other upon request)
1.0 inch
3-15 md, 20-30md, 70-90 md,90-150md, 1000+ md
2 to 35 %
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
44/99
UNSTEADY STATE GAS PERMEAMETER AND
POROSIMETER AT MODERATE CONFINING PRESSURE
(COREVAL 30)
PETROPHYSICS
The Coreval 30 instrument is dedicated to measure the porosity and permeability to helium of
plug sized core samples at a fixed confining pressure of 400 psi maximum. The instrument is
provided with a data acquisition and calculation computer station. Permeability measurements
are made using the unsteady state pressure drop method. This data is used to determine the
equivalent liquid permeability, slip and turbulence factors. Equivalent air permeability at a user
specified pressure is also computed. Porosity and pore volume measurements are made using
the Boyle’s and Charles’ law technique.
FEATURES
Permeability Range
Porosity Range
Pore Pressure
Confining pressure
Temperature
Helium
N2
Air
Power
up to 60%
250 psi
up to 400 psi
ambient
+/- 0.1 °C
0.1% F.S.
400 psi
500 psi
100 psi (dry)
220 VAC, 50 Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
45/99
UNSTEADY STATE GAS PERMEAMETER AND
POROSIMETER AT OVERBURDEN PRESSURE
(COREVAL 700)
PETROPHYSICS
The Coreval 700 instrument is dedicated to measure the porosity and permeability to helium
of plug sized core samples at multiple confining pressures ranging from 400 psi to 10,000 psi.
The instrument is provided with a data acquisition and calculation computer station.
Permeability measurements are made using the unsteady state pressure drop method. This data
is used to determine the equivalent liquid permeability, slip and turbulence factors. Equivalent
air permeability at a user specified pressure is also computed. Porosity and pore volume
measurements are made using the Boyle’s and Charles’ law technique.
FEATURES
Permeability Range
Porosity Range
Pore Pressure
Confining Pressure
Temperature
Helium
Air
Power
up to 60%
250 psi
400 psi to 10,000 psi
ambient
+/- 0.1 °C
0.1% F.S.
400 psi
100 psi (dry)
220 VAC, 50 Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
46/99
AUTOMATED SAMPLE LOADING UNSTEADY STATE
PERMEAMETER AND POROSIMETER AT OVERBURDEN
PRESSURE (KEYPHI)
PETROPHYSICS
The KEYPHI instrument is a fully automated permeameter and porosimeter used to determine
properties of plug sized core samples at reservoir confining pressure. The gas permeability
determination is based on the unsteady state pressure falloff method whereas the pore volume is
determined using the Boyles law technique. The instrument is provided with a unique automatic
core sample loading mechanism which can process multiple samples without any human
intervention. In addition, the instrument offers reporting and calculation facilities thanks to its
user-friendly windows operated software. Klinkenberg slip factor “b”, Klinkenberg corrected
permeability, inertial coefficients, sample bulk volume, sample porosity, grain volume are
automatically determined and presented on customised report.
FEATURES
Confining Pressure
Pore Pressure
Core diameter
Core length
Permeability Range
Porosity Range
Sample capacity
Helium
Air
Power
400-10,000 psi
250 psi
1" or 1.5"
0.75" to 3"
<0.001 to >10,000 md
0.1 > 40%
13 (1.5” diam. samples) and 16 (1” diam. Sample)
400 psi
125 psi (dry)
220 VAC, 50 Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
47/99
LIQUID PERMEAMETER (LIQPERM)
PETROPHYSICS
The Liquid permeameter is dedicated to measure permeability to liquid of plug sized core
samples at room conditions. The liquid permeability determination is based on the Darcy’s law
and assumes that one phase is present in the core and there is no rock fluid interaction. The
instrument is provided with a hassler coreholder, a transparent fluid vessel, a console with
pressure digital display, 3 interchangeable burettes for various permeability ranges, an
electronic timer for flow rate calculation and an Excel spread sheet calculation template. This
low cost apparatus is particular interested for educational purposes.
FEATURES
Permeability Range
Flow Pressure
Confining pressure
Temperature
Air supply
Power
0. 1md to 5 darcy
up to 100 psi
up to 400 psi
ambient
0.25% F.S.
250 psi
220 VAC, 50 Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
48/99
BENCH TOP PERMEABILITY SYSTEM (BPS 350)
PETROPHYSICS
The BPS350 permeameter is a manually operated system designed for performing simple
permeability tests at pore pressure to 5,000 psi with confining pressures to 10,000 psi. The
standard system includes a low pulsation HPLC pump for fluid delivery at flow rates from 0.01
to 10 ml/min. Plug core samples are held in a hassler coreholder mounted horizontally. The core
holder can accommodate 1.5” diameter core samples one to three inches in length. The system
is equipped with one differential pressure transducers and digital readout which has a range of
0-250 psid. A manual bypass valve is used to equilibrate pressure on the transducer preventing
damage at high differential pressures. A dome loaded backpressure regulator is utilized to
maintain downstream elevated test pressures. A manually operated hydraulic pump is used to
generate confining pressure up to 10,000 psi. An optional gas injection can be added to flow
nitrogen gas through the core sample to measure gas permeability.
FEATURES
Confining pressure
Pore pressure
Temperature
Core diameter
Core length
Loading type
Wetted material
Fluid
Power
700 bar (10,000psi)
350 bar (5,000psi)
ambient
1” or 1’’1/2
1’’ to 3’’
Hassler
stainless steel
Water and N2
220 VAC, 50 Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
49/99
BENCH TOP UNSTEADY STATE RELATIVE PERMEAMETER
(BRP 350)
PETROPHYSICS
The semi automated BRP350 allows for the determination of liquid permeability and liquid /
liquid relative permeability on plug sized core samples at overburden pressure. The test consists
of direct measurement of permeability while injecting oil, water or brine through the rock
sample. The system includes two floating piston accumulators, a HPLC pump, a hassler
coreholder, an overburden pump, a back pressure regulator and pressure display. The instrument
can also be configured for gas / liquid relative permeability measurement.
FEATURES
Confining pressure
Pore pressure
Temperature
Core diameter
Core length
Loading type
Wetted material
N2
Power
350 bar (5,000psi)
350 bar (5,000psi)
ambient
1” or 1’’1/2
1’’ to 3’’
Hassler
stainless steel
2,000 psi
220 VAC, 50 Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
50/99
BENCH TOP UNSTEADY & STEADY STATE LIQUID – LIQUID
RELATIVE PERMEAMETER (SRP 350)
PETROPHYSICS
The SRP350 relative permeameter allows for determination of the liquid / liquid relative
permeability on plug sized core samples at overburden pressure using unsteady and steady state
conditions. The core saturation is determined by measuring the resistivity of the core sample
during the flow test. The flow rates are controlled by the two pumps used to inject
simultaneously the fluids is the core sample.
FEATURES
Confining pressure
Pore pressure
Temperature
Core diameter
Core length
Loading type
Wetted material
N2
Power
350 bar (5,000psi)
350 bar (5,000psi)
ambient
1” or 1’’1/2
2’’ to 3’’
Hydrostatic
stainless steel
2,000 psi
220 VAC, 50 Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
51/99
ELECTRICAL PROPERTIES SYSTEM @ AMBIENT
CONDITIONS (EPS-A)
PETROPHYSICS
Complete system used for the determination of resistivity and formation factor of plug sized
sample at ambient conditions. The system permits to measure the rock resistivity Ro and the
brine resistivity Rw at different frequencies. The cell utilises a two and four electrode design.
The platens contact the core end faces under a constant pneumatic pressure up to 6 bar. This
minimises contact resistance artefacts which are often found where a screw or jack mechanism
is used to load the sample onto the electrode platens. The cell is provided with a plastic cover
box to minimise core saturation changes. The instrument also includes a dip conductivity probe
and a becher to measure the brine resistivity. An LCR meter is used to monitor the core and
brine resistance and capacitance.
FEATURES
Core diameter
Core Length
Resistivity measurement
Max pressure
Temperature
Power supply
Air
1” and 1.5”
up to 3”
2 and 4 electrodes
Atmospheric
Room condition
220 VAC 50 Hz
150 psi
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
52/99
ELECTRICAL PROPERTIES SYSTEM @ OVERBURDEN
PRESSURE (EPS 700)
PETROPHYSICS
The EPS 700 is used for the measurement of rock resistivity for both fully and partially brine
saturated core samples at overburden pressure. The system includes a hydrostatic electrical
coreholder, with hand pump for confining pressure generation, a pore pressure control panel for
core desaturation and a resistivity meter for 2 and 4 points core resistance measurement. The
system can be configured for multi sample configurations.
FEATURES
Core diameter
Core Length
Overburden pressure
Temperature
Power supply
Air
1” and 1.5”
up to 3”
2 and 4 electrodes
700 bar (10,000 psi)
Room condition
220 VAC 50 Hz
150 psi
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
53/99
CAPILLARY PRESSURE DESATURATION CELL
PETROPHYSICS
The multiple sample desaturation cell enables to desaturate a set of consolidated core samples
by the porous plate method. Data obtained can be used to calculate capillary pressure versus
saturation curves. A high precision weighing balance can be used for core saturation
measurement. The multiple sample desaturation cell is manufactured from stainless steel and is
equipped at its base with a large ceramic plate used as a semi permeable porous plate. The
desaturation cell consists of a pressure vessel, with an easy opening lid, clamping bolts, o’rings
seals, outflow tube assemblies and pressure control panel. Three ceramic plates are provided
with the systems withstanding each 3 bar, 5 bar and 15 bar pressure. The control panel includes
a digital pressure display, two low and high range pressure regulators and a set of control
valves. A gas humidifier is also provided to insure minimum evaporation during the
desaturation process.
FEATURES
Maximum desaturation process
Minimum desaturation process
Ceramic plate pressure
Wetted materials
Electrical requirements
Air Pressure requirements
200 psi
0.1 psi
3 bar, 5 bar and 15 bar
316 Stainless steel
220 VAC, 50 Hz
0- 200 psi (15 bar)
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
54/99
CAPILLARY PRESSURE REFRIGERATED CENTRIFUGE
(RC3000)
PETROPHYSICS
The RC3000 is a refrigerated centrifuge modified to enable rapid determination of capillary
pressure characteristics on six core samples simultaneously. It can also be utilized for rapid
sample preparation to restore state conditions for subsequent testing in various test equipment.
Custom designed sample chambers offer the ability to spin core plug samples up to 1.5 inches in
diameter at rotational speeds up to 3000 RPM. It includes a rotor and drainage cells which can
accommodate either 1”, or 1.5” diameter cores. A digital speed control with the ability to ramp
speeds at specified intervals and a precision temperature control system is included. An overtemperature setpoint stops the centrifuge if the temperature exceeds the setpoint by a specified
value. The system is also equipped with a sensor for rotor imbalance. It is equipped with a
digital camera system that allows to user to measure the displaced fluid volumes in each of the
cells sequentially.
FEATURES
PC range :
Oil-water drainage :
Oil-water imbibition:
Air-water drainage:
Air-water imbibition:
0.1 to 4.5 bar
-0.2 to -6 bar
0.2 to 9 bar
- 0.3 to -12 bar
Speed regulation:
Temperature:
Speed:
Large radius:
Power supply:
± 10 rpm
-20°C (@speed = 0) +40°C
from 500 up to 3 000 RPM
30 cm
220 VAC 50 Hz
BENEFITS
Fast capillary pressure run (1 to 2 days)
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
55/99
CAPILLARY PRESSURE MERCURY SYSTEM (CPM 140)
PETROPHYSICS
Manual operated system for the measurement of capillary pressure and pore morphology. Based
on Purcell method, mercury is injected into plug sized samples at know volume from vacuum to
2,000 psi (140 bar). The instrument uses a hand operated pump for mercury injection and a
coreholder equipped with an opening windowed chamber cap for easy loading / unloading
operations and mercury level visualization. The control panel includes the pore pressure
regulator, the pore pressure transducer with the digital display and a vacuum manometer.
FEATURES
Pressure range
Temperature
Core Diameter
Core length
Vacuum pumping speed
Final vacuum pressure
Power supply
Nitrogen source
up to 140 bar (2,000 psi)
ambient
1” or 1.5”
up to 3 inches
2.5 m3/h
10-3 mbar.
220 VAC, 50Hz
2,000 psi
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
56/99
DIGITAL CORE PHOTOGRAPHY SYSTEM (DCP)
PETROPHYSICS
The fully automated core photography system is designed for complete core photography and
archiving purposes, producing high quality white and ultraviolet colour images of full diameter
whole or slabbed core samples. The operator positions the core samples on a four rows rack and
a digital camera mounted above the core samples under white or ultra violet lighting takes a
high resolution picture. The images are then automatically digitised, displayed and recorded in
the high speed computer. The software includes calibration functions for the camera, image
processing capabilities as well as file compression, storage and transfer facilities. The
innovative concept is in the use of a digital camera which can produce very high resolution
color images up, avoiding the risk of deformed images.
FEATURES
Camera type
Camera resolution
File size
Interface
Internal PC hard drive
Maximum frame area
Data storage on CDROM
Weight
Power supply
35 mm Full frame
5616 x 3744 pixels
21 Megapixels
USB
80 GB
600 mm x 900 mm
RAW, JPG
200 kg
220 VAC , 50 Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
57/99
PETROPHYSICS
SPECIAL CORE ANALYSIS
Core Flood System
Formation Damage
Capri
Rock Compressibility
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
58/99
CORE FLOOD SYSTEM FOR EOR STUDIES (CFS 700)
PETROPHYSICS
The CFS 700 system provides a versatile facility to carry out core flood and fluid flow tests
studies at reservoir conditions of temperature and pressure. The core flood and fluid tests allow
for the evaluation of the effect of different fluids on rock permeability such as brine sensitivity,
return permeability, critical flow velocity, acid stimulation, EOR tests (secondary and tertiary
water flooding, polymer injection). The computer controlled system is provided with a unique
software that allows for operation both manual and automatic modes where all key components
can be controlled including pump, valves, video capturing and data acquisition. A test sequencer
also permits to program and run test sequences automatically. The coreholder, air operated
valves, produced fluid separator if selected and necessary plumbing are mounted in an airbath
that has been designed to provide easy access of all components. Several features can be used
to extend the capabilities of the system. Among them, the automated back pressure regulator
provides a very stable pressure control with fast response to pressure fluctuations and phase
transition. It can be used for single and multiphase flow system. The automatic confining pump
generates and maintains automatically a net overburden pressure thus avoiding to control
pressure changes during heating and cooling steps. The unique video separator provides an
extreme accuracy of the volume of brine, oil and gas produced during the flow tests at reservoir
conditions.
FEATURES
Confining pressure
Pore pressure
Maximum working temperature
Core diameter
Core length
Fluid flow rate
Wetted parts
Power supply
700 bar (10,000 psi )
depends on the injection pump model
150°C
1.5” other upon request
1”to 3” other upon request
depends on the injection pump model
Stainless steel, other type upon request
220VAC, 50Hz
7 bar (100 psi)
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
59/99
UNSTEADY STATE RELATIVE PERMEAMETER
(AUTOFLOOD 700)
PETROPHYSICS
The AUTOFLOOD 700 system provides a versatile facility to carry out unsteady state relative
permeability studies for liquid/liquid and liquid/gas at reservoir conditions of temperature and
pressure. The standard configuration allows for liquid /liquid tests at constant flow rate and
liquid/gas tests at constant pressure. A gas line permits to inject gas at constant pressure. The
same system can be configured for 3 phase unsteady state relative permeability measurements.
The computer controlled system is provided with a unique software that allows for operation
both manual and automatic modes where all key components can be controlled including pump,
valves, video capturing and data acquisition. A test sequencer also permits to program and run
test sequences automatically. The coreholder, air operated valves, produced fluid separator and
necessary plumbing are mounted in an airbath that has been designed to provide easy access of
all components. The automated back pressure regulator provides a very stable pressure control
with fast response to pressure fluctuations and phase transition. It can be used for single and
multiphase flow system. The automatic confining pump generates and maintains automatically a
net overburden pressure thus avoiding to control pressure changes during heating and cooling
steps. The unique video separator provides an extreme accuracy of the volume of brine, oil and
gas produced during the flow tests at reservoir conditions.
FEATURES
Maximum pore pressure
Maximum gas pressure
Core diameter
Core length
Material
Power supply
700 bar (10,000 psi)
700 bar (10,000 psi)
200 bar (3,000 psi)
150°C
1"1/2 other upon request
1” to 3” other upon request
Stainless steel
220VAC, 50Hz
7 bar (100 psi)
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
60/99
STEADY STATE AND UNSTEADY STATE RELATIVE
PERMEAMETER SYSTEM (RPS 700)
PETROPHYSICS
The RPS 700 system provides a versatile facility to carry out unsteady state and steady state
relative permeability studies for liquid/liquid and liquid/gas at reservoir conditions of
temperature and pressure. The standard configuration allows liquid /liquid and liquid/gas flow
tests to be conducted at constant flow rate. An optional gas line permits to run unsteady state
gas/liquid permeability tests at constant pressure. The computer controlled system is provided
with a unique software that allows for operation both manual and automatic modes where all
key components can be controlled including pump, valves, video capturing and data acquisition.
A test sequencer also permits to program and run test sequences automatically. The coreholder,
air operated valves, produced fluid separator and necessary plumbing are mounted in an airbath
that has been designed to provide easy access of all components. The unique high temperature
recirculating triple pump system presents an unprecedented solution to generate continuous,
pulse free fluid flow rate of one or more fluids through a sample while maintaining a constant
pressure at the outlet of the sample. The automatic confining pump generates and maintains
automatically a net overburden pressure thus avoiding to control pressure changes during
heating and cooling steps. The video separator also provides an extreme accuracy of the volume
of brine, oil and gas produced during the flow tests at reservoir conditions.
FEATURES
Core diameter
Core length
Flow rate
Material
Power supply
700 bar (10,000 psi)
700 bar (10,000 psi)
150°C
1"1/2 other upon request
0.005 to 50 cc/min
Stainless steel
220VAC, 50Hz
7 bar (100 psi)
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
61/99
XRAY SCANNER FOR IN-SITU SATURATION MONITORING
PETROPHYSICS
The Xray scanner is an add-on module to the relative permeability RPS700 rig and allows for
monitoring the in situ fluid saturations and distribution along the length of the core. The
standard configuration allows for liquid /liquid and liquid/gas saturation determination. The Xray scanner allows for measuring the attenuation of an X-ray beam sent through a core sample
to determine the phase saturation and saturation distribution along the length of the core sample.
The X-ray detector and generator are mounted on a motor driven table equipped with a high
accuracy position encoder. A composite coreholder is be used for these tests to avoid X-ray
absorption. The core temperature is maintained constant thanks to a heating system which uses
the confining fluid to heat the core by re-circulating it for homogenous temperature.
FEATURES
Core diameter
Core length
X-ray source
Wetted parts
Power supply
700 bar (10,000 psi)
700 bar (10,000psi)
150°C
1”5 other upon request
120 kV, 4 mA
Stainless steel
220VAC, 50Hz
7 bar (100 psi)
BENEFITS
The core sample temperature is homogenous all along the core.
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
62/99
PETROPHYSICS
FORMATION DAMAGE AND WELL TREATMENT
EVALUATION SYSTEM (FDS 350)
The FDS350 system enables to perform (a) liquid permeability measurement, (b) static filtration
tests, (c) mud invasion evaluation and (d) stimulation tests on a formation sample at reservoir
conditions of temperature and pressure. This instrument can be configured for the evaluation of
the effect of different fluids on rock permeability such as drilling fluids (water-based or oilbased mud), cement effluents, chemical wash treating fluids and acid corrosive treating fluids.
Initial permeability, return permeability, brine sensitivity, critical flow velocity, acid
stimulation, mud filtrate invasion can be monitored with this system. Drilling mud tests are
performed under realistic field conditions by flowing the fluids tangentially to the face of the
core, thanks to a special leak-off core holder. The system can be configured with a mud
recirculation pump to perform dynamic filtration tests so as to study erosion effects induced by
the fluid flowing across the core face which contains proppant and other particulates. The mud
pump flow rate of 6 l/min max ensures an efficient shear rate to simulate the real operating
conditions. The computer controlled system is provided with a unique software that allows for
operation both manual and automatic modes where all key components can be controlled
including pump, valves and data acquisition. A test sequencer also permits to program and run
test sequences automatically. The coreholder, air operated valves, mud pump and necessary
plumbing are mounted in an airbath that has been designed to provide easy access of all
components.
FEATURES
Maximum mud pressure
Core diameter
Core length
Mud flow rate
Material
Power supply
700 bar (10,000 psi)
350 bar (5,000 psi)
350 bar (5,000 psi)
150°C
2 to 4” other upon request
up to 6 liter/min (option)
Stainless steel, Titanium, hastelloy
220VAC, 50Hz
7 bar (100 psi)
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
63/99
CAPILLARY PRESSURE AND RESISTIVITY INDEX SYSTEM
(CAPRI)
PETROPHYSICS
The CAPRI system is dedicated to the determination of the capillary pressure curves (positive
and negative) and the electrical resistivity index as a function of core sample saturation at
reservoir conditions. Saturation exponent “n”, formation factor and cementation exponent “m”
are also calculated. The instrument consists of a core holder furnished with hydrophobic and
hydrophilic ceramics and electrodes pattern for resistivity measurement, an automated pumping
system for fluid control and a resistivity cell for brine resistivity measurement. The whole is
housed in a temperature controlled air bath.
FEATURES
Max pore pressure
Working temperature
Capillary pressure range
Core length
Core diameter
Power supply
Brine wetted material
700 bar (10, 000 psi)
700 bar (10,000 psi)
up to 150°C
10 to +10 bar (145 psi)
2” up to 3”
1 ½” other upon request
220VAC, 50Hz
stainless steel
BENEFITS
Measurement are made at reservoir conditions of pressure and temperature
Direct capillary pressure measurement
High temperature pump located in the controlled temperature air bath to reduce volume measurement
error induced by temperature fluctuations.
Multiple core samples configuration available
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
64/99
ROCK COMPRESSIBILITY SYSTEM (RCS 700)
PETROPHYSICS
The RCS 700 apparatus is designed to monitor pore and bulk volume changes under various
levels of radial and axial confining pressures at reservoir temperature. The apparatus consists of
a triaxial core holder located in a constant temperature air bath to restore the reservoir
conditions on the core sample. The pump cylinder is used to generate and control the pore
pressure while the other two pump cylinders are used to generate the axial and radial confining
pressures. The volume variations of fluid injected into or expelled from the core sample can be
monitored with an extreme accuracy. Automated tests can be programmed to perform a number
of measurements at different steps of pressure and temperature without user’s intervention.
FEATURES
Core Diameter
Core Length
Max pore pressure
Max axial / radial confining pressure
Stroke volume of pump
Working temperature
Volume measurement accuracy
Pressure measurement accuracy
Material
Power supply
1 1/2" other upon request
700 bar (10,000 psi)
700 bar (10,000 psi)
100 cc
ambient to 150° C
0.001 cc
0.1 %
Stainless steel
220VAC, 50Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
65/99
ATMOSPHERIC ACOUSTIC VELOCITY SYSTEM (AVS A)
PETROPHYSICS
The AVS A allows for the measurement of acoustic velocity of a core sample at atmospheric
pressure and ambient temperature. It is used to propagate compressional and shear waves
through core samples, calculate acoustic velocity and determine dynamic elastic constants such
as the dynamic moduli, Young’s, bulk and shear, along with Poisson’s ratio. The system
consists of an atmospheric coreholder, acoustic transducer assemblies, acoustic Pulser / receiver
and digital oscilloscope.
FEATURES
Operating pressure
Operating temperature
Core sample length
Center frequency
Mode
Power supply
Atmospheric
up to 50°C
1” and 1.5” other upon request
500 KHz
compressional (P) and shear (S1 & S2)
220VAC, 50Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
66/99
OVERBURDEN ACOUSTIC VELOCITY SYSTEM (AVS 700)
PETROPHYSICS
The AVS 700 allows for the measurement of acoustic velocity of a core sample under a wide
range of pore and confining pressures. It is used to propagate compressional and shear waves
through core samples, measure pore pressure, confining pressure and temperature, calculate
acoustic velocity and determine dynamic elastic constants such as the dynamic moduli,
Young’s, bulk and shear, along with Poisson’s ratio. The system consists of fully equipped
pressure vessel, acoustic transducer assemblies, confining pressure controller, pore pressure
controller, acoustic Pulser / receiver and digital oscilloscope.
FEATURES
Operating pressure
Core sample length
Center frequency
Mode
Power supply
Up to 700 bar (10,000 psi)
up to 50°C
500 KHz
220VAC, 50Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
67/99
AUTOMATED HP-HT ACOUSTIC VELOCITY SYSTEM
(AVS 700-HT)
PETROPHYSICS
The AVS 700-HT apparatus allows for the measurement of acoustic velocity of a core sample
under various levels of pore pressure and radial/axial confining pressures at reservoir
temperature. The apparatus permits to propagate compressional and shear waves S1 and S2
through core samples, generate and measure the pore pressure and confining pressure, calculate
acoustic velocity at reservoir conditions and determine dynamic elastic constants (Poisson ratio
and Young modulus). The system consists of three automated pumps and a fully equipped
acoustic triaxial coreholder housed in a constant temperature air bath to restore the reservoir
conditions on the core sample. One pump cylinder is used to generate and control the pore
pressure while the other two pump cylinders are used to generate the axial and radial confining
pressures. A pulser-receiver is used to produce an electrical pulse to excite a piezoelectric
transducer and an oscilloscope measures the travel time of the pulse between the two
transducers. This data is then used to calculate the acoustic velocity of the core sample.
FEATURES
Operating pressure
Core sample length
Center frequency
Mode
Power supply
Up to 700 bar (10,000 psi)
up to 150°C
500 KHz
220VAC, 50Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
68/99
AGING CELL APPARATUS (ACA 700)
PETROPHYSICS
The apparatus is designed for aging core samples with crude oil so as to restore its reservoir
wettability before being used for a SCAL study. The base version is delivered with five core
units. The aging method entails first saturating a cleaned (and thus water wet) core plug with
brine. The brine is then displaced by crude oil until representative initial water saturation is
achieved. During this process the smaller pores remain water –filled, whereas the oil invades the
remainder of the pore space, leaving thin water films on the pore walls and in crevices. Finally,
the core containing crude oil and connate water is left for many weeks at reservoir temperature
and pressure. It is at this stage that wettability changes may occur in the oil-invaded pores.
However, these changes are dependant upon the stability of the water wet films, trapped
between the rock surface and the oil. The pore walls can only become oil-wet if contacted by oil
due to the rupture of these films. In this case the core will have achieved a mixed wettability
state status.
FEATURES
Operating pressure
Core sample length
Fluid flow rate
Wetted part
Air requirement
Power supply
up to 700 bar (10,000 psi)
up to 150°C
1” and 1.5”
1 to 3”
up to 10 cc/min
Stainless steel
100 psi
220VAC, 50Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
69/99
PETROPHYSICS
COREHOLDERS
Hassler CH
Triaxial CH
Leakoff CH
Stands
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
70/99
HASSLER COREHOLDER (HAS SERIES)
PETROPHYSICS
The HAC Series core holders are standard Hassler type core holders used for fluid flow testing.
With the coreholder assembled and the sleeve in place the core is inserted into the loading end.
The platen is then pushed in and held in place by the cap which can be screwed on by hand and
allows 50 mm adjustement. Further adjustment is possible with the use of interchangeable
spacers fitted to the loose platen. An inlet and outlet distribution plug allows fluids and gases to
be injected through the core sample. A unique feature of the HAC series core holder is that the
sleeve remains in place and the core is loaded from one end without having to drain or refill the
confining fluid. By releasing the confining radial pressure and unscrewing the end plug, the core
sample can be easily removed without exposing it to the annulus fluid. The core holders can be
provided to have interchangeable core diameters.
FEATURES
Performance specifications
Operating pressure rating:
Operating temperature:
Fitting:
Core diameter:
Core length:
Wetted parts:
Sleeve material
Inlet port:
Outlet port:
HAC series
5,000, 10,000 psi, 15,000 psi
Ambient or 150°C
NPT, Autoclave or HIP
Customer specified
Customer specified
Stainless steel, Hastelloy, titanium
Viton
As request
As request
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
71/99
HYDROSTATIC COREHOLDER (HYC SERIES)
PETROPHYSICS
The HYC Series core holders are standard hydrostatic type core holders in which radial and
axial confining pressures are common. These core holders are routinely used for gas and liquid
permeability testing and water flooding experiments. The coreholder has a fixed platen at one
end over which the rubber sleeve is mounted and located in the other end of the sleeve is a
floating platen connected via a ¼” diameter tubing passing through the outside. For variable
length cores, this design insures solid contact between the platen and core sample. To change a
core sample the confining fluid must be drained off and the knurled screwed ring removed by
rotating anti clockwise by hand. This will withdraw the fixed platen together with the sleeve,
core and floating platen. After removal of the two platens from the sleeve the core can be
withdrawn. Loading a new core sample is carried out in the reverse order. The advantage of this
type of coreholder is that the overburden pressure acts on the end of the core as well as the
diameter. The coreholder can be equipped with a number of pressure taps molded in the sleeve
at discrete locations required by the end user. This design allow to monitor the pressure drop
along the length of the core sample during fluid flow tests. Electrical pressure tap can also be
provided to monitor the resistivity of the core sample during a permeability test.
FEATURES
Fitting:
Core diameter:
Core length:
Wetted parts:
Sleeve material :
Inlet port:
Outlet port:
Pressure tap :
HYC series
5,000, 10,000 psi, 15,000 psi
Up to 150°C
Customer specified
Customer specified
Viton
As request
one
As request
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
72/99
TRIAXIAL COREHOLDER (TRC SERIES)
PETROPHYSICS
The TRC Series core holders are standard triaxial type core holders in which radial and axial
loading are independent. These core holders are routinely used for fluid flow experiments. A
unique feature of the TRC series core holder is that the sleeve remains in place and the core is
loaded from one end without having to drain or refill the confining fluid. Independent axial
pressure is applied via a floating distribution plug. An inlet and outlet distribution plug allows
fluids and gases to be injected through the core sample. A unique feature of the TRC Series core
holder is that the holder does not need to be completely disassembled to remove the core
sample. By releasing the confining radial and axial pressure and unscrewing the eng plug, the
core sample can be easily removed without exposing it to the annulus fluid. The coreholder can
be configured for hassler loading, hydrostatic loading or triaxial loading.
FEATURES
Fitting:
Core diameter:
Core length:
Wetted parts:
Sleeve material :
Inlet port:
Outlet port:
TRC series
5,000, 10,000 psi, 15,000 psi
Up to 150°C
Customer specified
Customer specified
Viton
As request
As request
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
73/99
LEAKOFF COREHOLDER (LEC SERIES)
The LEC Series core holders are mainly used for static and dynamic filtration tests so as to
study erosion effects induced by the fluid flowing across the core face which contains proppant
and other particulates. The coreholder features a special head that allows the upper face of the
core sample to be exposed to invasion fluids. The fluids can be injected from both ends of the
core holder then simulating the wellbore and the reservoir side. The coreholder can be equipped
with a number of pressure taps molded in the sleeve at discrete locations required by the end
user. This design allow to monitor the pressure drop along the length of the core sample during
fluid flow tests.
PETROPHYSICS
.
FEATURES
Fitting:
Core diameter:
Core length:
Wetted parts:
Sleeve material :
Inlet port:
Outlet port:
Pressure taps :
LEC series
5,000, 10,000 psi
Up to 150°C
NPT
Customer specified
Customer specified
Viton
As request
As request
As request
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
74/99
QUICK RELEASE COREHOLDER (QRC SERIES)
PETROPHYSICS
The QRC Series core holders allows for the core to be loaded without the complete disassembly
of the coreholder. The core loading is achieved using an innovative ¼ turn fast release bayonet
mechanism. The coreholder is configured for hassler loading. The sleeve remains in place and
the core is loaded from one end without having to drain/refill the confining fluid which can be
nitrogen or hydraulic oil. This avoids damage to the sleeve which can occur with assembly and
disassembly. Operation is much easier and quicker and leads to higher throughput when tests of
short duration are being carried out.
FEATURES
Fitting:
Core diameter:
Core length:
Wetted parts:
Sleeve material
Inlet port:
Outlet port:
QRC series
400 psi, 1000 psi
Ambient or up to 80°C
NPT
Customer specified
Customer specified
Stainless steel
Nitrile
1
1
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
75/99
TRANSPARENT COMPOSITE COREHOLDER (TCC SERIES)
PETROPHYSICS
The TCC Series core holders are standard hydrostatic type core holders. These core holders are
used for gas and liquid permeability testing with in situ saturation monitoring. The core holder
uses a thin aluminium liner which is over wrapped with carbon fibre composite and epoxy to
avoid important loss of X-ray. Spiral fluid distribution grooves on core inlet are incorporated to
minimise capillary end effects. The coreholder can be provided with an heating system which
heats and re-circulates the confining fluid through the annular confining chamber for optimal
temperature homogeneity.
FEATURES
Fitting:
Core diameter:
Core length:
Wetted parts:
Sleeve material
Inlet port:
Outlet port:
TCC series
Up to 10,000 psi,
Ambient or up to 150°C
NPT
Customer specified
Customer specified
Viton
As request
As request
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
76/99
ACOUSTIC VELOCITY COREHOLDER (AVC SERIES)
PETROPHYSICS
The AVC Series core holders are standard triaxial type core holders in which radial and axial
loading are independent. These core holders are routinely used for acoustic velocity
measurement at reservoir conditions. The coreholder features a pair of acoustic transducers that
propagate compressional and two plane-polarized shear waves through the core sample. The
triaxial loading insures a proper surface contact between the transducer and the core. An inlet
and outlet distribution plug allows fluids to be injected through the core sample. The coreholder
does not need to be completely disassembled to remove the core sample. A tool permits to
orientate easily the P&S1,S2 transducer before the acoustic velocity measurement takes place.
FEATURES
Center frequency
Fitting:
Core diameter:
Core length:
Wetted parts:
Sleeve material
Inlet port:
Outlet port:
AVC series
10,000 psi, 15,000 psi
Ambient or 150°C
700 KHz
Customer specified
Customer specified
Stainless steel
Viton
1
1
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
77/99
ELECTRICAL RESISTIVITY AND CAPILLARY PRESSURE
COREHOLDER (ECP SERIES)
PETROPHYSICS
The ECP Series core holders are standard hydrostatic type core holders. These core holders are
routinely used for electrical resistivity and capillary pressure at reservoir conditions. The
coreholders feature both water wet and oil wet porous ceramics placed between the flow
distribution plugs and the core sample. Four electrodes have been molded directly into the
sleeves and are used to measure the resistivity of the sample. Two of them are provided with
metal ring placed into the sleeve along the core length at one inch spacing between the rings.
The other two electrodes are in contact with the distribution plugs which are electrically isolated
from the rest of the coreholder.
FEATURES
Capillary pressure
Connection
Core diameter:
Core length:
Wetted parts:
Sleeve material
Inlet port:
Outlet port:
ECP series
10,000 psi,
Ambient and up to 150°C
2 and 4 points
Positive and negative
NPT
Customer specified
Customer specified
Stainless steel
Viton
2
1
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
78/99
HEATING SYSTEM (HES SERIES)
PETROPHYSICS
The electrical heating system can be provided to heat and maintain homogeneous temperature in
the core sample. The system uses two half heating shelves maintained by two clamps that fit
the shape of the coreholder in order to provide the highest heat efficiency. A digital temperature
controller is used to enter, display and regulate the temperature . A thermocouple probe is used
to measure the temperature of the coreholder body.
FEATURES
Temperature accuracy:
Power:
HES series
Ambient to 150°C
0.1 °C
220 VAC, 50 Hz,
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
79/99
STANDS (STA SERIES)
PETROPHYSICS
A number of stands are available depending on the End user’s requirement. Simple to most
complicated designs can be proposed. The stand can be mounted inside or outside of the airbath.
The stand can also be configured in a bench top or bench floor version.
FEATURES
STA series
Coreholder position:
Fixed Horizontal,
Fixed horizontal and vertical,
Swivelling
Ambient and up to 150°C
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
80/99
PETROPHYSICS
CORE ANALYSIS COMPONENTS
Level Tracker
BPR
Vacuum Pump
Pressure Generator
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
81/99
LEVEL TRACKER SEPARATOR (LTS SERIES)
PETROPHYSICS
Designed to measure the volume of liquid produced during a process at ambient conditions. The
device is made of a precision bore calibrated glass liquid collector, a motor driven level detector
composed of a tracking fork with 2 optical fibers (light path of emitter and sensor) and a
converter (light / voltage), an encoder to log the liquid level and a computer interface to control
the instrument and to log and display the liquid volume versus time.
FEATURES
Temperature
Collector capacity
Volume accuracy
Wetted parts
ambient
100 ml or 300 ml
0.1 ml
glass
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
82/99
DUAL LEVEL TRACKER (DLT SERIES)
PETROPHYSICS
Designed to measure the volumes of the two liquid phases produced during a process at ambient
conditions. The device is made of a precision bore calibrated glass liquid collector and two
motor driven level detector used to monitor the first water / oil interface and the second oil / Gas
interface. Each detector is composed of a tracking fork with 2 optical fibers (light path of
emitter and sensor) and a converter (light / voltage), an encoder to log the liquid level and a
computer interface to control the instrument and to log and display the liquid volume versus
time.
FEATURES
Temperature
Collector capacity
Volume accuracy
Wetted parts
Power supply
Weight
Dimensions (HxWxL)
ambient
100 ml or 300 ml
0.1 ml
glass
220 VAC 50 Hz
30 kg
800 mm x 250 mm x 250 mm
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
83/99
AMBIENT CONDITIONS TWO PHASE VIDEO SEPARATOR
(VSE -A)
PETROPHYSICS
The video separator is a precision device used for separating and determining the oil, brine or
gas volumes that are produced from a core sample during a two phase relative permeability test.
It consists of a separation bore used for collecting and separating produced fluids under gravity
and a measurement bore used for visualising the two phases fluid interface at room conditions.
The measurement bore consists of a glass tube to allow for sample visibility. Placing a light
behind the tube allows easy discernment of the two phases interface level. Measurement of
produced fluids during the displacement test is performed with a video camera which monitors
the position of the interface of the two fluids produced from the core sample in the measurement
bore of the separator. The position of the interface is directly proportional of the volumes of
fluids produced from the core sample and so of the change in the core saturation. The high
resolution camera is equipped with an integrated zoom and a back lighting installed in the rear
side of the tube. The camera is connected to the computer station so that the image of the fluid
can be displayed and recorded on the PC. The video software incorporates facilities which
enable to detect automatically the liquid/ liquid and gas/ liquid interface and so derive the
volumes of produced fluids from the core and so the changes in the core saturation.
FEATURES
Max pressure …………………
Max temperature………………
Max volume change…………..
Volume accuracy…………...…
Material……………………….
Measurement resolution……..
Minimum field of view……….
CDD colour camera……….….
Lighting ……………………...
Power………………………...
Atmospheric pressure
up to 40 °C
30 ml
0.01 ml
Glassware
0.02 mm
50 mm
440,000 pixels
20 watts
230 VAC, 50, 60 Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
84/99
HP-HT TWO PHASE VIDEO SEPARATOR (VSE 700)
PETROPHYSICS
The apparatus is designed to separate the two phase fluids produced from the core at reservoir
conditions. It consists of a separation bore used to collect and separate produced fluids under
gravity and a measurement bore used to visualise the two phases fluid interface at reservoir
conditions. The measurement of produced fluids is performed with a video tracker designed to
monitor the position of the interface of the two fluids which is directly proportional of the
volumes of fluids produced from the core sample. The video tracker system comprises a high
resolution camera equipped with an integrated zoom, a back lighting installed in the rear side
and a motorized linear stage that is used to position the camera relative to the fluid interface to
be measured. The linear stage and the camera are both connected to the computer station so that
the image of the fluid can be displayed and recorded on the PC. The video software incorporates
facilities which enable to detect automatically the liquid/ liquid and gas/ liquid interface and so
derive the volumes of produced fluids from the core and so the changes in the core saturation.
FEATURES
Max pressure …………………
Max temperature………………
Max volume change…………..
Volume accuracy…………...…
Material……………………….
Measurement resolution……..
Minimum field of view……….
CDD colour camera……….….
Lighting ……………………...
Power………………………...
10,000 psi
150 °C
100 ml, option: 300 ml
0.01 ml
Sapphire, Stainless steel, option: Titanium
0.02 mm
10 mm
440,000 pixels
150 watts
230 VAC, 50, 60 Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
85/99
WET GAS METER (WG SERIES)
PETROPHYSICS
Designed to measure the volume of gas produced during a process at ambient conditions such as
gas-liquid relative permeability. The meter is complete with thermometer, spirit level, levelling
feet and gas connections. An option computer interface is available to acquire and display the
gas volume versus time.
FEATURES
Temperature
Pressure
Capacity
Scale
Maximum pressure
Flow range
Maximum capacity
Ambient
Atmospheric
25 dm3 (i.e. 0.25 litres) per revolution
0.001 dm3
65 mbar
30 to 90 litres per hour +/- 0.5%
99,999 litres
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
86/99
CAPILLARY SIGHT GLASS TUBE
PETROPHYSICS
The capillary sight glass tube provides a means to visually confirm miscibility of displaced
fluids during dynamic processes such as slim tube miscibility experiments and core
displacement test. The cell is made with a glass capillary tube embraced with two flanges at its
ends.
FEATURES
Max pressure
Temperature
Wetted parts
10,000 psi
up to 150°C
Stainless steel, sapphire
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
87/99
BACK PRESSURE REGULATOR (BPR)
PETROPHYSICS
Vinci offers back pressure regulators designed to regulate the pressure in fluid flow studies. The
BPR consists of two chambers separated by a piston with a needle connected to it on the lower
side. The upper chamber receives the gas dome pressure and the lower chamber the process
pressure. The BPR acts a comparator. When the dome pressure is higher than the process
pressure the needle seals off the pressure and maintains the pressure. Inversely when the process
pressure exceeds the dome pressure the needle opens up and the excess process fluid flows out.
That way, on continuous flow these 2 stages are looped continuously and the process pressure is
balanced to the dome controlled constant value.
FEATURES
Maximum pressure
Flow rate
Max Temperature
Wetted part material
Port connection
10,000 psi
0.01 to 25 cc/min
150°C
stainless steel
1/8”
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
88/99
ELECTRICAL ISOLATOR (EI 700)
The EI 700 is designed to electrically isolate one side of a core holder from the other when
placed in a non-conductive fluid stream. It can be used for reservoir condition electrical
properties during a relative permeability or a capillary pressure displacement test.
PETROPHYSICS
FEATURES
Maximum pressure: 10,000 psi
Max Temperature: 150°C
Internal volume: less than 1 cc
Wetted part material: stainless steel, peek
Port connection: 1/8”
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
89/99
AUTOMATED CONFINING PRESSURE CONTROLLER
(ACP 700)
PETROPHYSICS
The ACP 700 is designed to generate and maintain automatically a constant confining pressure
requested during core studies. It can also be used to maintain a constant differential pressure
between the pore pressure and confining pressure. The system consists of a positive
displacement pump of 100 cc capacity and 10,000 psi pressure, an automatic dual valve, a fluid
reservoir and two pressure transducers for pore and confining pressure control.
FEATURES
Confining pressure
Pore pressure
Pump cylinder capacity
Air requirement
Tubing connector
Power
Wetted parts
up to 10,000 psi
up to 10,000 psi
100 cc
100 psi
1/8”
220 VAC 1 Ph, 50 Hz
Stainless steel
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
90/99
FLOATING PISTON ACCUMULATOR (FPA SERIES)
PETROPHYSICS
The floating piston accumulators are available in a range of different volume and pressure
rating. These can be constructed in different material such as 316 stainless steel, aluminium,
titanium or hastelloy. The fluid seals may either be the standard Viton / Nitrile ‘O’ rings and
PTFE back up ring.
FEATURES
Pressure
Temperature
Cell volume
Material
5,000 psi, 10,000 psi or 15,000 psi
Ambient to 150°C (300 °F)
100 cc, 300 cc, 500 cc, 700cc, 1,000cc, 2,000 cc, 5000 cc
316 stainless steel, aluminium, titanium or hastelloy
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
91/99
MIXER CYLINDER (MC SERIES)
PETROPHYSICS
The MC series are double end piston type cylinders designed to store and mix any kind of fluids
at pressure and temperature. The sample fluid is isolated from the secondary driving fluid with a
floating piston and a magnetic mixer is located in the mixing sample chamber for proper
agitation. The mixer is magnetically coupled to a drive system through the accumulator end cap
which incorporates a permanent magnet driven by a direct current motor with variable speed. A
mixer controller permits to stop, start and control the speed of the mixer. The cylinder can be
operated in either upright or inverted orientation. Both end caps are provided with an inlet/outlet
port for fluid introduction or fluid sampling.
FEATURES
Model
MC 500-10
MC 1000-10
MC 2000-10
MC 500-15
MC 1000-15
MC 2000-15
(1)
Volume
ml
500
1,000
2,000
500
1,000
2,000
Pressure
psi
10,000
10,000
10,000
15,000
15,000
15,000
Temp.
°C
150
150
150
200
200
200
Weight
Kg
21
25
35
21
25
35
Length
mm
700
750
900
700
750
900
Diameter
mm
120
120
150
120
120
150
Material
(1)
Stainless steel
Stainless steel
Stainless steel
Stainless steel
Stainless steel
Stainless steel
Thread
connection
¼” FNPT
¼” FNPT
¼” FNPT
1/8” FLP
1/8” FLP
1/8” FLP
Titanium material available.
Mixer controller
Power requirement…………………… 230 VAC, 50 Hz, 100 W
BENEFITS
H2S resistant
The impeller provides a minimum dead volume
Provide rigorous agitation of entire fluid sample
Capable of mixing high viscosity samples up to 1,000 cp
High speed, allows equilibrium to be reached in minimum time
Reduces operating time for establishing phase equilibrium on sample.
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
92/99
FLUID TRANSFER VESSELS (FTV SERIES)
PETROPHYSICS
The fluid transfer vessels uses a glass tube embraced in two end plugs which are held in place
with two aluminium tie bars. The glass tube is protected by an external polycarbonate tube in
case of failure of the glass. The top end plug can be removed easily to load the fluid in the
vessel. The fluid is transferred from the vessel to another accumulator by applying air pressure
on the top port while the fluid passes through the bottom port of the vessel.
FEATURES
Pressure
Volume
Material
Fluids
150 psi
1,500 cc (other upon request)
Glass
brine, oil, mud, drilling fluid, etc
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
93/99
HYDRAULIC INTENSIFIER (HI SERIES)
PETROPHYSICS
The HI series are dual cavity cylinders equipped with a low pressure (LP) bore at one end and a
high pressure (HP) bore at the other end. The pistons in each cylinder bore are connected by a
solid rod. When pressurized fluid enters the larger bore, the fluid in the smaller bore is
compressed to a pressure multiplied by the ratio of areas on the two pistons. Consequently,
pressures up to 150Kpsi can be achieved by using a commercially available lower pressure (10
Kpsi) pump. Material of construction is either stainless steel or titanium.
FEATURES
Model
Ratio
HP end
LP end
HI 2
2 :1
Volume
ml
50
Pressure
psi
20,000
ID
mm
25.46
Stroke
mm
98.24
Pressure
psi
10,000
ID
mm
36
HI 4
4 :1
25
40,000
18.00
98.24
10,000
36
HI 6
6 :1
20
60,000
14.70
117.89
10,000
36
HI 8
8 :1
15
80,000
12.73
117.89
10,000
36
HI 10
10 :1
10
100,000
11.38
98.24
10,000
36
HI 15
15 :1
5
150,000
9.30
73.68
10,000
36
Additional features:
Temperature
Thread connection
Material
Weight
Length
Diameter
ambient
¼” FNPT (Low pressure side ) and ¼” FHP (High pressure side)
Stainless steel or titanium
Approx. 22 Kg
600 mm
90 mm to 120 mm depending on the model.
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
94/99
PRESSURE GENERATOR SYSTEM (PGS)
PETROPHYSICS
Designed to provide hydraulic pressure for Hg free fluid transfer at pressure condition.
Maximum output is 10,000 psi. The system comes complete with control valves, air driven
liquid pump, pressure gauge, air regulator, relief valve and frame.
FEATURES
Max outlet pressure
Air inlet
Wetted parts
10,000 psi
30 to 145 psi (10 bar).
Stainless steel,
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
95/99
DIGITAL PRESSURE GAUGE (DPG SERIES)
PETROPHYSICS
The Digital Pressure Gauge series is designed for extremely accurate pressure measurement to
meet your most demanding requirements for precision laboratory or field measurement
instrumentation. The instrument includes a high precision analog pressure transducer, a
rupture disc for over pressure protection, a five digit digital display and a data logging
software for automatic data acquisition.
FEATURES
Model
Pressure range
Accuracy
Port connection
Wetted part
Power supply
DPG series
up to 10,000 psi (other range available)
0.1% FS
1/8” autoclave type
stainless steel
220 VAC 1 Ph, 50 Hz
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
96/99
DEADWEIGHT GAUGE
PETROPHYSICS
Primary pressure standard designed for high pressure calibration applications. The device
consists of a vertically mounted precision lapped piston and cylinder assembly. Accurately
calibrated masses are loaded onto the piston, which rises freely within its cylinder. These
weights balance the upward force created by the application of pressure within the system.
Delivered with a carrying case.
FEATURES
Model
Operation
Pressure range
Accuracy
Dual piston
Oil operated
1 bar (15 psi) to 1,100 bar (16,000 psi)
0.015% RDG
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
97/99
UNINTERRUPTABLE POWER SUPPLY (UPS 16)
PETROPHYSICS
Back-up power protection used in most laboratories against electrical noise, sags, surges and
brownouts which affect the sensitivity of the electrical components of the laboratory equipment.
FEATURES
Output power capacity
Max configurable power
Input voltage
Output voltage
Efficiency at full load
Back up time
12,800 Watts / 16,000 VA
12,800 Watts / 16,000 VA
240 V +-1 %, single phase
240 V +-1 %, single phase
90%
6 minutes at full load (12,800 watts)
17 minutes at half load (6,400 Watts)
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
98/99
PETROPHYSICS
OTHER COMPONENTS
Vacuum pump: Based on double stage rotary vane pump and featuring a max pumping speed
of 2.5 m3/h and a vacuum rate of 10-3 mbar.
Air compressor: Designed to generate compressed air of 7 to 10 bar when compressed air is not
available.
Controlled temperature air bath: Designed to provide homogeneous temperature with
extreme accuracy. A large range of air bath is available depending on temperature ranges,
dimension and temperature homogeneity accuracy. The air bath can be provided with one or
two front and rear doors and with or without windows.
Thermostatic bath: Designed to provide heating and cooling source with an accurate
regulation.
Fraction collector: Inline effluent fraction collector for collecting up to 70 individual liquid
sample fractions automatically on a time or volume basis
PH meter: Inline pH probe and meter for monitoring effluent pH as a function of time.
VINCI TECHNOLOGIES
Phone: 331 41 37 92 20 Fax: 331 41 37 04 76
99/99

catalog CORE

Transcription

Similar documents

Battlegrounds and beluga - Office du tourisme de Québec

GRUE TOUT-TERRAIN DE 1500 TONNES PRÈS DE LA CHUTE

october - Tourisme Laurentides

Celebrate Your Special Moments

Two-part agritourism tour – 2 days

Pet licences - Ville de Gatineau

RS Series Brochure

#104 300 Klahanie Drive • Port Moody

ePPa CSr CerTIfICaTIon fIrST dozen honoured

cycling tour - Velo