Facility Standards Manual

Town of Purcellville
Material Specifications &
Standards Booklet
*Accompanying Document to the Town of
Purcellville Facilities Standards Manual*
Revised Date: March 26, 2008
Page 1
Material Specification Booklet
Town of Purcellville
This Document accompanies the Town of Purcellville Facilities Standards Manual
Adopted: 6/11/96 by Town Council
Latest Revision: 3/26/2008
Introduction
The Materials Specification Booklet is intended as a companion to the Facilities
Standards Manual. The materials listed represent the materials acceptable for use in
constructing facilities in the Town of Purcellville and the Urban Growth Area. These
materials have been specified in this book because they most suit the specific design
criteria, maintenance needs, and cost requirements for the Town of Purcellville. Where a
manufacturer’s name and/or model number is specified no substitutions will be allowed.
Any products not specified in this booklet shipped to projects within the town or urban
growth area shall be deemed unresponsive to the town’s authority and shall be removed
and replaced with approved materials at no cost to the town.
All pipe, fittings, and other related materials used in the construction of lines shall be in
full compliance with the latest modifications and/or revisions to this document and the
ASTM, ANSI and AWWA specifications.
This materials specifications book is divided into two separate categories: Water
Distribution System and Sewer Collection System. The table identifies the items used to
construct these systems and provides the acceptable manufacturers and model numbers.
Any deviation from the items specified will not be accepted by the town. Any items not
specified in this booklet must meet all the specifications described in the latest version of
the Town of Purcellville Facilities Standards Manual.
For any items required for streets that are not listed in this document, please refer to the
VDOT specifications. This would include all storm water management structures, signs,
etc.
The Materials Specification Booklet will be updated regularly by the town as the need
arises. The latest revision date is printed on the bottom left hand corner of each page.
Please check to be sure you have the latest revision of this document before purchasing
any materials.
Page 2
Water Distribution System
Items for Water
Distribution
Manufacturer
Model # or Type
Water Lines
Griffin
Atlantic States
Clow
Mueller Centurian
American Flow Control
Mueller to 12”
Mueller above 12”
American Flow Control
Geneco
Fast Fabricators
Mueller
American Flow Control
Pratt
Mueller
Valmatic
Apco
Bernard
Mueller
Tyler Pipe
Bingham and Taylor
Class 52 DIP
Stewart
Carson
Tyler Pipe
Griffin Pipe
S-FBK-FF 1/8
C-FBK-FF 1/8
Compact
AWWA C153
1100 Series
1400 Series
2800 A ORC
Full Body Style
ASTM A53680
ASTM A53665-45-12
Fire Hydrants
Gate Valves
Valve Nut Extensions
Swing Check
Valves
Butterfly Valves
Combination Air
Release & Air
Vacuum Valves
Blow Off Valve
Valve Boxes
Bolts and Gasket
Kits
Mechanical Joint
Fittings, Hydrant
Tees
Elbows and Sleeves
Mech. Joint Restraints/
Mega Lug Glands
Mechanical Joint
Tapping Sleeves
Union Foundry
EBAA Iron Mega Lugs
Ford Meter Box Co.
American Flow Control
Mueller
Page 3
ANSI/AWWA
spec.* or other
requirement
C151/A121.51
AWWA C151
Super Centurian 250
B62B 4’ D.O.B.
A 2360-20
A 2361-20
AFC 2800
1’ Increments
AWWA C502
A 2600-6
50 SC
AWWA C508
Ground Hog
Line Sealer 3
VM 201C & VM202C
143C & 145C
4415
A-2360
564S
BT 22
AWWA C509
ASTM A126
Class B
AWWA C110
ASTM A43862
Water Distribution System
Items for Water
Distribution
Manufacturer
Model # or Type
ANSI/AWWA
spec.* or other
requirement
Same as Above, Old
Mueller
Full Body Style
Pipe
Repair Clamps
Ford Circle
Stainless Steel
* Must meet the requirements of the ANSI/AWWA and or ASTM standards as described
Wall pipe/Sleeve/ Flg
Spools – Ductile Iron
Pipe and Flanges
Service Line Fittings
Service Tubing
Threaded Fittings
Service Saddles
Ball Corporation
Stops
Coppersetters
1” or Less
Single service 1-1/2”
Single service 5/8”
Single serivce 1”
Double service 5/8”
Single service 2”
Dual Cartridge Style
Check
Meter Box
Single service 5/8”
Single service 1”
Double service 5/8”
Meter Box Covers
5/8” to 2”
Higgins Eng.
Davis - K
Clow
Ford Meter Box Co.
Mueller
Mueller
Howell
Merit
Lee Brass
Ford Meter Box Co.
Mueller
Smith Blare
Ford Meter Box Co.
Mueller
Ford
Ford Meter Box Co.
Ford Meter Box Co.
Ford Meter Box Co.
Ford Meter Box Co.
Ford Meter Box Co.
Ford Meter Box Co.
Mueller
Mid-States Plastics
Mid-States Plastics
Mid-States Plastics
Ford Meter Box Co.
MBC
MBC
Page 4
Class 53 DIP
AWWA C115
C44 series
110 series
Soft type K copper
Soft type K copper
Red Brass
Red Brass
FS202 Series
H10500 DR25CC
313
FB Series 1000Q
300 Series B-25008
Compression
AWWA C800
ASTM B88
70 Series
VBHH66-15B11-66
ANSI B16.15
Double Strap
Type
AWWA C800
AWWA C800
W/ dual bypass
Check valve
VBHC172-12W4433
VBHC174-15W4444
VBHC172-12W1433
VBHH77-15B 11-77
HHC series
AWWA C800
H14460 Series M98
ASTM D1505
18” by 30”
Hi density
24” by 30”
Polyethylene
36” by 36”
A32T, Single
Cast Iron
Recessed
74MAL115RTCP,
Single Recessed
32TT, Dual Surface
Meter Box Cover
Extension Rings
Cold Water Meters
Blow Off Hydrants
Yard
Pavement
Sampling Stations
Mechanical Joint
Connections
Ford Meter Box Co.
MBC
Kupferle Foundry
Mueller
Kupferle Foundry
Infact Corporation
NO #1
NO 18-24
T-10
Cast Iron
AWWA C700
#78
A-2360
NO88-WC (Eclipse)
Foster Adaptor
Sewer Collection System
Items for Sewer
Collection System
Gravity Sewer Mains
PVC (6” to 27”)
Gravity Sewer Mains
PVC (36” to 48”)
Gravity Sewer Mains
Manufacturer
Model #
6”-12” DR 18
ANSI/AWWA
spec.* or other
requirement
AWWA C900
14”-27” DR 25
AWWA C905
Vylon
Ultra Core
Ultra Rib
ASTM F794
46 PSI
ASTM F794
46 PSI
National Pipe
NAPCO
ETI
J.M.
Carcon
ETI
ETI
Americast
AGRU Sure Grip
PVC Ribbed(15”-30”)
Manhole Lining, All
over 18’ or Receiving
Force Main Flows
Manhole Internal
Chimney Seals
Manhole Adjusting
Rings
Gravity sewer laterals
Inside ROW or Town
Easement
Force Main (PVC)
Force Main
Ductile Iron Pipe
Cretex
Ladtech
HDPE
National
NAPCO
DR 18
AWWA C900
DR 14
AWWA C900
CL52
ANSI/AWWA
C151/A21.51
National
ETI
NAPCO
Griffin
Atlantic States
Clow
Page 5
Force Main HDPE
Sewer Main Fittings
Sewer Saddles
Pressure Fittings
Mechanical Joint
Fittings
Ball Curb Stops
EHMW SDR 11.5
Harco
Freedom
Romac Industries CB
HARCO
Tyler Pipe
Griffin Pipe
Union
Ford Meter Box Inc
Mueller
Page 6
SDR 35
CB
SDR 21
PVC, ASTM
D-3034
DI ASTM 536
PVC ASTM
D1784
AWWA C153
Compact
B11
AWWA C800
Ball Valve Extension
Stems
Gate Valves
Air Release & Air
Vacuum Valve
Valve Boxes
Detectable Marking
Tape
Gate Valve Extension
Stems
Clean Out
Adapters & plug
Clean out wye
Geneco
Trumble
American Flow Control
Mueller
Valmatic
APCO
Tyler Pipe
Bingham & Taylor
Line Tech Systems
Allen Systems
Geneco
Trumble
EST ST-3.0
250 PSI R.S.
801 BW, 802 BW
24x36
36x48
6” Wide
ASTM A-3684A
AWWA C509
ASTM A126
Class B
Cast Iron
Green w/ black
“Sewer line below”
EST ST-3.0
ASTM A-3684A
Jones Manufacturing
Harco
SDR 35
ASTM D-2665
Freedom
* Must meet the requirements of the ANSI/AWWA and or ASTM standards as described
Page 7