RESUBMIT 0092839.Numark.GTL.R2.AwcFT英1

ITEM #0092839
10 FT. SQUARE STEEL GAZEBO
MODEL #S-J-109D
Français p.10
Español p.19
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-643-0067, 8 a.m. – 8 p.m., EST, Monday – Friday.
1
PACKAGE CONTENTS
H
J
I
C
F
D
E
G
A
B
Part
Description
Quantity
Part
Description
Quantity
A
Side panel post
4
F
Canopy frame bar
4
B
Triangular mesh shelf
4
G
Short connect bar
4
C
Canopy frame center piece
1
H
Wind vent canopy
1
D
Top crossbar
4
I
Large canopy
1
E
Top crossbar with metal bracket
4
J
Top insect net
1
2
HARDWARE CONTENTS
Part
Description
Quantity
Picture (Shown to size)
AA
M4 x 20 L bolt
4
BB
M6 x 30 L bolt
8 + 1 spare
CC
M6 x 40 L bolt
4
DD
M6 x 80 L bolt
16 + 1 spare
EE
M6 metal washer
FF
M4 nut
4
GG
M6 nut
28 + 1 spare
HH
"L" connect bracket*
4
II
Lawn stake*
8
JJ
"S" hook*
4
KK
M6 nut cap
36 + 2 spares
LL
M6 bolt cap
4
8 + 1 spare
Also Included:
Wrenches
4
n /a
Touch up paint
1
n /a
*Not to scale.
3
SAFETY INFORMATION
WARNING
•
The gazebo is heavy. Handle with care. The gazebo requires two people for safe assembly.
CAUTION
•
•
•
Assemble the gazebo on a soft, non-abrasive surface (such as grass) to avoid damage.
The gazebo is not intended to be a permanent structure. Disassemble in the event of inclement
weather (strong wind, heavy rain, etc.) to avoid damage.
KEEP ALL FLAME AND HEAT SOURCES AWAY FROM CANOPY FABRIC. This canopy is
made with flame-resistant fabric, which meets CPAI-84 specifications. It is not fire proof. The
canopy fabric will burn if left in continuous contact with any flame source. The application of
any foreign substance to the canopy fabric may render the flame-resistant properties
ineffective.
PREPARATION
Before beginning assembly of the product, make sure all parts are present. Compare parts with
package contents list and diagrams on pages 2 and 3. If any part is missing or damaged, do not
attempt to assemble the product. Contact customer service for replacement parts.
Estimated Assembly Time: 1.5 hours (does not include unpacking time)
Tools Required for Assembly: Wrenches (provided), Phillips screwdriver (not provided), and an M4
hex wrench (not provided)
Helpful Tools: Drill with 4 mm hex bit, and 10 mm socket wrench
ASSEMBLY INSTRUCTIONS
1)
2)
On a flat, level surface, stand one side panel
post (A) upright with the black rubber base at the
bottom. Open the side panel post (A) to form a
90-degree angle. See Figure 1.
Place a triangular mesh shelf (B) in the corner
of one side panel post (A). Push the shelf (B)
down until the bracket on the shelf (B) sits
securely on the side panel post (A). See
Figure 2.
Repeat steps 1 and 2 for the three remaining
side panel posts (A).
4
Figure 1
A
Figure 2
A
B
ASSEMBLY INSTRUCTIONS
3)
The top crossbar with metal bracket (E) is preassembled. Place an M6 nut cap (KK) over each
pre-installed nut.
Repeat procedure for the three remaining top
crossbars with metal brackets (E). See
Figure 3.
E
Hardware Used
Part
KK
4)
Insert a top crossbar (D) into a top crossbar
with metal bracket (E). Line up the holes and
insert two M6 x 30 L bolts (BB) through the top
crossbar with metal bracket (E) first, and then
through the top crossbar (D). Fasten with an M6
nut (GG) using the provided wrenches to tighten
the M6 x 30 L bolts (BB). Do not overtighten!
Description
M6 nut cap
Quantity
8
E
D
KK
GG
BB
Repeat the procedure for the three remaining top Hardware Used
crossbars (D) and top crossbars with metal
Part Description
brackets (E). See Figure 4.
M6 x 30 L bolt
BB
M6 nut
8
KK
M6 nut cap
8
Repeat this procedure for the other side of this
corner, the three remaining assembled
crossbars (D & E), and the side panel posts
(A). See Figure 5.
5
Picture
Figure 5
D
E
DD
Note: The holes closest to the corner are used in
Step 6 to secure the "L" connect bracket (HH).
Do not secure them in this step.
Place an M6 nut cap (KK) over each M6 nut
(GG).
Quantity
8
GG
Place one assembled crossbar (D & E) on top
of the side panel posts (A). Line up the holes at
each end of the assembled crossbar (D & E)
with the holes in the top of the side panel posts
(A). Insert an M6 x 80 L bolt (DD) through the
holes furthest from the corner.
Fasten with an M6 nut (GG) using the provided
wrenches to tighten the M6 x 80 L bolts (DD).
Do not overtighten!
Picture
Figure 4
Place an M6 nut cap (KK) over each M6 nut
(GG).
5)
Figure 3
KK
GG
KK
A
Hardware Used
Part
DD
Description
M6 x 80 L bolt
Quantity
8
GG
M6 nut
8
KK
M6 nut cap
8
Picture
ASSEMBLY INSTRUCTIONS
6)
Place one "L" connect bracket (HH) on the top
of an assembled crossbar (D & E) and line up
the holes. Insert an M6 x 80 L bolt (DD). Fasten
with an M6 nut (GG) using the provided
wrenches to tighten the M6 x 80 L bolts (DD).
Do not overtighten!
Figure 6
E
D
DD
HH
Place an M6 nut cap (KK) over each M6 nut
(GG).
GG
Repeat the procedure to attach the three
remaining "L" connect brackets (HH). See
Figure 6.
KK
Hardware Used
Part
7)
DD
Description
M6 x 80 L bolt
GG
M6 nut
8
HH
"L" connect bracket
4
KK
M6 nut cap
8
Assemble the canopy frame bars (F), to the
short connect bars (G) by pressing the button
on the short connect bar (G) and inserting into
the canopy frame bar (F). The button will pop
out of the hole on the canopy frame bar (F)
when it is secure.
Quantity
8
Figure 7
C
F
Repeat the procedure for each of the three
remaining short connect bars (G).
Picture
C
G
F
Follow the same process to assemble the
canopy frame center piece (C) to the canopy
frame bars (F). See Figure 7.
8)
Figure 8
Place the large canopy (I) over the top of the
assembled frame (C, F and G) and align the
seams of the large canopy (I) with the frame
bars (F & G). See Figure 8.
Pull the top piece of the canopy frame bars (F)
out from under the large canopy (I). See
Figure 8.
IMPORTANT! Do not slip the corner pockets of
the large canopy (I) into the end of the short
connect bars (G) in this step. This takes place in
Step 12.
6
C
I
G
F
F
ASSEMBLY INSTRUCTIONS
9)
Insert the top piece of the canopy frame bars
(F) into the "U" bracket on the canopy frame
center piece (C). Line up the holes and insert an
M4 x 20 L bolt (AA). Fasten with an M4 nut (FF)
using an M4 hex wrench and Phillips head
screwdriver to tighten the M4 x 20 L bolts (AA).
Do not overtighten! See Figure 9.
Figure 9
F
C
AA
FF
Hardware Used
Part
AA
Description
M4 x 20 L bolt
FF
M4 nut
10) Place the wind vent canopy (H) over the top of
the canopy frame bar (F). Slip the poles into
each corner pocket of the wind vent canopy (H),
completely covering the canopy bars. See
Figure 10.
11) Place the fully assembled canopy on the top of
the assembled panel posts. Line up the holes on
each of the short connect bars (G) with the
holes on the "L" connect brackets (HH).
Insert an M6 x 40 L bolt (CC) and M6 metal
washer (EE), through the "L" connect bracket
(HH), and the short connect bars (G), and then
add one more M6 metal washer (EE). Fasten
with an M6 nut (GG) using the provided
wrenches to tighten the M6 x 40 L bolts (CC).
IMPORTANT! Do not tighten completely!
Repeat this procedure for the three remaining
corners.
Quantity
4
4
H
Figure 10
F
H
F
Figure 11
CC HH
LL
KK
EE
I
GG
G
EE
G
I
Hardware Used
Use the provided wrenches to securely tighten all
of the M6 x 40 L bolts (CC). Do not
overtighten!
CC
Description
M6 x 40 L bolt
EE
M6 metal washer
8
Place an M6 nut cap (KK) over each M6 nut
(GG). Place an M6 bolt cap (LL) over each M6
x 40 L bolt (CC). See Figure 11.
GG
M6 nut
4
LL
M6 bolt cap
4
KK
M6 nut cap
4
7
Picture
Part
Quantity
4
Picture
ASSEMBLY INSTRUCTIONS
12) Slip the four ends of the short connect bars (G)
into four corner pockets of the large canopy (I).
See Figure 12.
Figure 12
I
I
G
Figure 13
13) Secure the gazebo to the ground by inserting
lawn stakes (II) through the holes in the bottom
of the side panel posts (A) and into the ground.
See Figure 13.
II
A
Hardware Used
Part
II
14) From inside the gazebo, attach the top insect
net (J) underneath the canopy by lining up the
edge of the Velcro® and pressing firmly.
Description
Lawn stake
Quantity
8
Picture
Figure 14
F
JJ
J
Insert the "S" hooks (JJ) through the rings
hanging on each canopy frame bar (F). The "S"
hooks are for hanging decorations. See
Figure 14.
Hardware Used
Part
JJ
8
Description
"S" hook
Quantity
4
Picture
ASSEMBLY INSTRUCTIONS
Figure 15
15) Secure the canopy to the crossbars (D & E).
Wrap the Velcro® straps under the bar and attach
to the canopy. See Figure 15.
E
D
CARE AND MAINTENANCE
Wash with mild soap, rinse with water and let air dry.
WARRANTY
This warranty is extended to the original purchaser and applies to defects in materials and
workmanship of your patio furniture provided your furniture is maintained with care and used only for
personal, residential purposes.
Frames are warranted to be free from defects in material or workmanship for a period of one (1) year.
Cushions, Straps and/or Wicker Weaves are covered for a period of one (1) year against defects in
material or workmanship. Sling fabric is covered for a period of one (1) year against defects in
material or workmanship.
Exclusions: Items used for commercial, contract or other non-residential purposes; display models;
items purchased “as is;” or items damaged due to acts of nature, vandalism, misuse or improper
assembly are not covered. Discoloration or fading of the finish or fabrics as a result of exposure to the
elements, chemicals or spills is not covered. Tabletop breakage, corrosion or rusting of hardware and
damages to frames or welds caused by improper assembly, misuse or natural causes are not
covered.
If within the stated warranty period a product is found to be defective in material or workmanship, the
purchaser must contact the manufacturer’s customer service department at 1-800-643-0067. The
manufacturer, at its option, will repair or replace the defective parts.
Warranty is to the original purchaser and is non-transferable. Any replacement of warranted items will
be in the original style and color or a similar style and color if the original is unavailable or has been
discontinued. As some states do not allow exclusions or limitations on an implied warranty, the above
exclusions and limitations may not apply. This warranty gives you specific rights, and you may also
have other rights which vary from state to state.
Printed in China
9