*SullivanToolCatalogue

Transcription

hand tool
catalogue
s u l l i v a n FA B R I C AT I O N S T U D I O
Instructional Fabrication is a division within the department
of Instructional Resources & Facilities Management (IRFM).
www.saic.edu/instructionalfabrication
C O N TE N TS
Instructional Fabrication’s mission is to serve the contemporary
art making needs of the School of the Art Institute of Chicago
by providing instruction and technical assistance to students
and faculty using the School’s shops and fabrication facilities.
Our staff work collaboratively across artistic and academic
disciplines to support all manners of fabricating art objects.
Measuring Tools
2
Clamps & Guides
8
Cutting Tools
14
Strike Tools
24
Manual Fasteners
26
Drilling & Boring
34
Sanding & Shaping
38
Heat Tools
48
Fabric & Pressing
51
Safety
52
Accessories
54
Index
60
Accurate weight scale for measuring items
up to 10 lbs.
Graduated Cylinder
Chalk Line
Clear plastic cylinder used to measure and
pour liquids. Do not use to mix plaster.
A layout tool ideal for marking straight lines
over moderate to long distances where a
square is inadequate.
100’ Measuring Tape
Measuring Tape
Like a regular measuring tape but 100’ long.
WOW!
Retractable measuring device ideal for
measuring medium to moderate distances
where a ruler is inadequate.
Available in 26 feet (8 meters)
M eas u r ing Too ls
Digital Scale
Laser guided thermometer, quite accurate
with a range of 15’
SAIC SULLIVAN INSTRUCTIONAL SHOP
2
Digital Thermometer
3
A smaller version of the standard level for
measuring in tight circumstances.
Ruler
Trammel Compass
Useful for measuring and rendering straight,
short to medium length lines as well as acting
as a very effective straight edge for cutting with
utility knives.
Used for marking large circles on drawings or workpieces where a standard
compass is inadequate.
Available Sizes:
12 inches, 36 inches & 48 inches
Combination Square
T-Square
Measuring and marking tool useful for a
variety of layout tasks including checking
90° and 45° angles.
Drafting tool used for rendering straight lines
perpendicular to a reference surface.
Torpedo Level
Used to check either an object’s level
(parellel with ground plane) or plumb
(perpendicular to ground plane).
4
Level
5
A layout tool used for marking and transferring various angles among workpieces;
unmarked for degree increments.
A handy and durable shop square with
90° and 45° measurements and a scale
for calculating rise/run.
Marking Gauge
Compass
Used to scribe a straight line on wood
or other soft materials relative to one
straight edge.
Used to render circles of variable diameter
on a drawing or workpiece.
Protractors
Calipers
Measuring and drafting tool useful in
determining or rendering the slope of
an angle.
Measuring tool used to determine workpiece
diameter.
Speed Square
6
Bevel Gauge
7
Small vise for drilling or work holding with
the benefit of an integrated miter function for
adjusting the working angle.
C Clamps
Drill Vise
Great for a strong hold down in tight
circumstances.
Vise used for holding smaller parts on the
drill press.
Grey Uni-Clamps
K-Body Clamps
Small version of K-Body clamps. Provide
two parallel clamping faces and a protected
clamping surface.
Bar clamps with deep reach, and consistently parallel clamping face. In addition the
the K-Bodys clamping jaws are plastic and
thus better able to protect the surface of the
clamped object.
Available sizes:
12” 24” & 48”
C l amps and G u ides
Corner Vise
A stout vise with jaws at 90° for clamping
and holding two members at 90°. Works
great for clamping frames or holding parts.
8
Corner Clamp
9
An extremely adjustable clamp useful
for clamping and holding oddly shaped
materials.
Available sizes:
16” length with a 4” 6” or 8” throat
10
F Clamp
Dowel Drilling Jig
General use medium duty clamp suitable for
glue ups and various hold down purposes.
A handy jig for drilling holes appropriately
centered for dowel joints.
Available sizes:
10, 16, 22, & 28” lengths
Klick Clamps
Pocket Hole Jig
A light duty clamp exerts minimal
pressure with a simple one handed
motion. Good for delicate glue-ups
where stronger clamps might mar
a surface.
An assembly jig designed specifically for
piloting and driving screws into two workpieces oriented at 90°. Pocket Hole joints
make for a fast, yet strong alternative to
laborious hand jointery.
Hand Screw Clamp
Heavy duty f-shaped clamps with a
remarkable reach.
Wetzler F Clamps
11
Quick Clamp
12
Used for temporarily holding two objects
together. Ideal for light duty applications
where the distribution of clamping
pressure is not of major concern.
Strap Clamp
(aka Band Clamp) A clamp ideally suited
for clamping or holding oddly shaped
workpieces on which other kinds of flat
clamps are unusable. The strap clamp
acts like a very tight belt.
Spring Clamp
saic SULLIVANa hand tool catalogue
saic SULLIVAN hand tool catalogue
A clamp with an easily adjustable tightening mechanism useful for light clamping
and work-holding purposes. Quick clamps
are easy to use but do not supply as much
clamping pressure as other, more rigid types
of bar clamps and thus are unsuitable for
many gluing applications.
13
A compact, Western style (cuts on the push)
saw with a narrow kerf well suited for cutting
dovetails.
A bayonet shaped saw for cutting holes in
the center of materials. Works best on softer
materials such as drywall and foam but can
be used on wood or composites.
Utility Knife
Fletcher Blades (4x)
A tool with a retractable, replaceable
razor-like blade, the utility knife is superb
for cutting all sorts of material. From paper
to cardboard to fabric, the utility knife can
produce very controlled and workable cuts.
This tool is best used with a straight edge or
other cut controller to minimize hazards of
an exposed and extremely sharp blade.
Blades which mount in the Fletcher panel
cutter and are material specific (Acrylic, Mat,
Glass, Paper).
Metal Shears
Wood Carving Set
The metal shears are like scissors for thin
gauge metal.
This set is for carving and detailed shaping.
Solid wood use only.
Available in a variety of profiles
C utting Too ls
Key Hole Saw
C utting Too ls
14
Dovetail Saw
15
A versatile shearing tool suitable for
papers and lightweight cardboards.
Another scissor-like tool for cutting thin gauge
metal. Tin snips have slightly less leverage than
shears, but produce a more controlled, clean cut.
Utility Scissors
Wire Stripper
Good for the kind of tough applications
where your mom would say, “Not with my
good sewing scissors!”
A plier-like instrument specifically designed to
strip and cut multiple gauges of wire as well as
crimp common wire quick connectors.
Fabric Scissors
Pneumatic Shears
For cutting fabric and fabric only.
A metal cutting tool, like a pair of scissors for
cutting thin gauge metal but with the added
power of pneumatics.
C utting Too ls
Tin Snips
C utting Too ls
16
Scissors
17
A Western-style saw (cuts on the pushstroke) specifically for making short
rip cuts, particularly those common in
furniture joints like the dovetail and the
mortise and tenon.
Coping Saw
Hack Saw
A saw with a narrow flexible blade useful
for cutting curves and detailed shapes by
hand. A hand powered scroll saw.
A saw with replaceable blades suited for
cutting metal and other non-wood materials.
Combination Saw
Bamboo Saw
A Western-style handsaw (cuts on the
pushstroke) equally suited for making
rip and crosscuts. Does not produce a
finished edge.
A spineless pull saw originally designed
for crosscutting bamboo, but these saws
are great for wood and foam as well.
C utting Too ls
Back Saw
An Eastern-style saw (cuts on the pull
stroke) which incorporates both a ripping
blade and crosscutting blade in one saw.
Because the saw has no spine, it is well
suited for cutting thick material and
performs well on both wood and foams.
C utting Too ls
18
Pull Saw
19
A rotary power tool which can be fitted with
a wide variety of router bits for profiling the
edges of material or for cutting grooves of
various geometry within the face. Used mostly on wood and wood composite material.
Hole Saw Set
Trim Router
A hybrid offspring of the drill bit and the
saw blade. Hole saws are excellent for
drilling round holes in thick materials
where other drill bits might struggle.
Similar to the plunge router only smaller.
The trim router is ideal for routing smaller
areas on which a plunge router is too
large to be effective.
Jig Saw
Biscuit Jointer
A hand held power tool fitted with a
linear cutting blade, the jigsaw is ideal for
making curved cuts in flat wood or wood
composite material. The jig saw can be
thought of as a portable band saw.
The biscuit jointer cuts matching slots in
the adjacent faces of the material to be
joined. A pre-cut “biscuit” of wood is then
inserted during glue-up. Biscuit joints
are quick, accurate, very strong, and are
of great help when it comes to laminating multiple parts while maintaining their
planarity.
C utting Too ls
Plunge Router
(aka Pneumatic Nibbler) Powered off
the pneumatic air system, the pneumatic
nibbler makes fast and clean cuts in thin
gauge metals like metal flashing.
C utting Too ls
20
Pneumatic Nipper
21
Pneumatic Hand Saw
C utting Too ls
C utting Too ls
Powered off of the pneumatic air system,
the pneumatic saw is an open-ended saw
useful for making free form rough cuts in
foam and other very soft materials.
22
23
Budget chisels suitable for dirty or
messy jobs like chiseling dry glue
or hacking at plaster; they cover the
type of jobs you would never do with
other fine edge chisels…right…?
To the hammer, all the world is a nail.
Straight Chisel Set
Rubber Mallet
This set is for removing wood and cutting
straight sided mortises.
A hammer-like instrument with a forgiving
hard rubber head for making last minute
adjustments during glue-up and other
operations which need striking force, but
where a steel headed hammer would
damage the workpiece.
Available from ¼ inch to 1” wide
Wooden Mallet
Ball Peen Hammer
Mallet made of wood. Less likely to dent soft
surfaces than a steel headed hammer or mallet.
Lightweight hammer with a flat face on one
side of the head and a ball face head on the
other. The ball side of the head is good for
sinking concavities in metal or adding that
authentic hammer texture to anything you
wack on.
Str i k e Too ls
Claw Hammer
C utting
Str i k e Too ls
saic SULLIVAN
SULLIVAN INSTRUCTIONAL
hand tool catalogue
SAIC
SHOP
24
20
Glue Chisels
25
A tool used for driving screw type fasteners
by hand. Available in many sizes and screw
head profiles.
Mini Screwdriver Set
Fixed Wrench Set
Very small screwdrivers for removing the
teeny-tiny screws commonly found in
electronic components etc.
The traditional style wrench for loosening
and tightening hex bolts of a fixed size.
Available in metric and standard sizes
Adjustable Wrench
Allen Wrench Set
A useful tool for loosening and tightening multiple or unknown sized hex bolts.
Can be adjusted to fit both metric and
standard sizes.
Hexagonal profiled wrenches made specifically
to interface with allen keyed fasteners.
Available in Metric and Standard
Man u a l Fastene r s
Screw Driver
Screwdriver with removable bits of
various profiles.
Man u aStr
l Fastene
s
i k e Toor
ls
saic SULLIVAN
hand tool catalogue
SAIC
SHOP
20
26
Screwdriver Set
27
Ratchet Set
Hand Hole Punch
A driver set for tightening and loosening
hexagonal headed bolts.
A stout hand punch with a throat capacity of
apx. 1-1/2” Can be used on leather and light
gauge metals.
28
Flat Crowbar
Used to set grommets in fabric which in turn
strengthen holes in fabric and help resist
tearing. Common in sails and other places
where fabric might be critically tied in position.
Grommet set includes an anvil, a punch,
and the male and female components of the
grommet.
Useful as a lever for general construction
purposes. Also useful as a high leverage nail
puller for pulling large or stubborn nails.
Riveter / Pop Rivet Gun
Tool specifically for setting pop
style rivets.
Slip Jaw Pliers
Similar to flat jaw pliers but with increased
jaw capacity, slip jaw pliers also incorporate a
channel locking system which allows the user
to grip large objects while still applying parallel
jaw pressure.
M an u a l Fastene r
Grommet Tool Set
Man u a l fastene r
Available in metric and standard
29
A plier-like tool with an adjustable locking
mechanism suitable for grabbing and holding
items with more force than could be applied
with the flat jaw pliers.
Needle Nose Pliers
Flat Jaw Pliers
Pliers with a long tapered nose for
grabbing and holding small objects.
Needle nose pliers also include an
integrated set of wire cutters near
the handle.
Flat jaw pliers are best suited for gripping
and pulling flat sided material.
Staple Gun
18 GA Stapler
A hand powered staple gun which shoots light
duty staples. Perfect for stretching canvas and
other fabric to wood attachments.
Pneumatic powered stapler with a staple
length range of ½” to 1-1/2”. Generally
best when finish nails do not offer enough
holding power.
Needle Nose Locking Pliers
Identical in function to the needle nose
locking pliers but with a wider and firmer
grasping head.
Man u a l fastene r
30
Locking Pliers
31
16GA Nailer
A tool powered by the compressed air
line, much like the cordless pin nailer.
The pneumatic pin nailer shoots very
small (23GA) pin nails for fastening wood
where a light to very light hold is needed.
23GA Pin Nailer
Man u a l fastene r
Pneumatic powered nailer with a fastener
range of 1” – 2-1/2”. Fires medium gauge
wire nails with a small head.
32
33
34
A drill handled driver which strikes as it
drives. Very good for driving into harder
materials or with long screws.
A cordless drill with a chuck situated
perpendicular to the handle. This drill is
capable of getting into tight quarters where
other drills cannot.
High Torque Drill
Pneumatic Drill
An 18 volt cordless drill with a high and
low torque setting. Best when you have a
bigger job to tackle.
Standard Torque Drill
A light and compact 12 volt drill. This
drill has only one torque setting but is
suitable for most normal drilling tasks
you might encounter.
A small pneumatic powered drill. The
pneumatic drill never runs out of batteries and
is quite a bit smaller than a corded drill. Great
for repetitive assembly.
Corded Drill
Similar to the cordless drill in power but with
a cord so it never runs out of juice.
D R I LL I N G & B o r ing
Right Angle Drill
Impact Driver
35
Cordless Drill
A battery powered drill for freehand drilling
operations and driving fastners. Should not
be used with drill bits 1” diameter
or above.
Forstner Bit Set
Type of drill bit ideal for cutting large
holes in harder woods; leaves a flat
bottom hole. Only appropriate for use
on the drill press.
36
Counter Sink Bit
(aka Twist Drill Bit Set) General duty
drill bit can be used on most materials in
either the drill press or in a hand drill.
A drilling and driving combination set for
screw piloting and driving.
Paddle Bit Set
(aka Spade Bit) Type of drill bit ideal for
cutting larger holes in softwood. Only
appropriate for use on the drill press.
Available in sizes from ¼ inch – 1¾ inch diameter
Drill Bits
Available in sizes from ¼ inch – 2 inch diameter
37
Rasp
Shinto Rasp
A coarse metal-toothed abrading device
suitable for fast material removal but
which leaves a very rough finished
surface. Faster abrasion than a file and
much coarser than any sandpaper.
An awesomely simple hybrid rifler-rasp with a
coarse side and fine side. Removes material
quickly and resists clogging. Works wonders for
shaping both foam and wood.
38
Small shaped rasps great for detailing small
areas which would otherwise be hard to
shape. Not for use on plaster.
Flat File
A medium coarse metal toothed abrading
device. Finer than a rasp, but more aggressive than sandpaper. Do not use on plaster.
Available in various profiles
Surform Shaver
Fine FIle
A very coarse metal toothed abrading
device. Slightly more aggressive than
the rasp.
A detail file with closely packed teeth best
for filing in small areas where a higher degree
of finish is desired and where quick material
removal is not the object.
SA nding & S haping
Detail Rasp Set
SA nding & S haping
Also Available: Round Rasp
39
saicSULLIVAN
SULLIVANINSTRUCTIONAL
hand tool catalogue
SAIC
SHOP
40
20
Low Angle Block Plane
Also referred to as a pocket plane, this handsized block plane is great for fine cleanup in
hard and softwoods. The blade is set at 12°,
so gentle cuts are recommended. If sharp, a
low angle block plane is also suitable for end
grain. Wood only.
Convex Sole Block Plane
Smoothing Plane
A setup similar to a standard block plane
(small and maneuverable, best for general
cleanup), but with a rounded sole. Works
well for cleaning up concave areas like chair
seats. Use on wood only.
Used for flattening large surfaces.
Solid wood use only.
Fore Plane
Jack Plane
Midway between a jack and jointer plane, this
robust bench plane surfaces long areas well,
especially with denser woods.
The workhorse of hand planes. Used for roughing and initial smoothing of boards. To be used
on solid wood only!
SA nding & S haping
SA nding & S haping
Used for light shaping and small scale
flattening. This tool is sharp and precise, and
leaves a smooth finish. Solid wood use only.
Block Plane
41
Shoulder Plane
MIni Belt Sander
A narrow bodied plane for removing
material in grooves, rabbets or along a
tenon’s shoulder (hence the name). To be
used on solid wood only.
A powered sanding tool for quickly
sanding flat areas. Not suited for sanding
rounded areas.
42
Pneumatic Orbital Sander
Manager approval and TA supervision
required. No overnight checkout allowed.
A sander, which runs on the pneumatic air
line but in most other ways works like
other palm sanders. The pneumatic orbital
sander is quieter and leaves a better-finished
surface. This sander must be used on the
downdraft table.
Palm Sander
Pneumatic Die Grinder
A powered sanding tool for sanding great
areas efficiently and effectively. Works
well on flat and rounded areas.
Similar to a dremmel tool but more
powerful and with larger diameter burrs.
Replacement sandpaper available for free through
tool checkout
SA nding & S haping
Large Belt Sander
SA nding & S haping
Available in Medium
43
Dremel Tool
44
Used for shaping medium to long cylindrical
stock. Solid wood use only.
Available in flat and round bottom
Draw Knife
An old timey tool used for roughly shaping
long rectangular or cylindrical stock. Cuts
on the pull. Solid wood use only.
SA nding & S haping
Spoke Shave
SA nding & S haping
A rotary tool that accepts bits of different
profiles for detail shaping and carving of
various materials.
45
A flexible sanding pad which accepts PSA
(pressure sensitive adhesive) sanding discs.
Great for hand sanding curved surfaces.
Sharpening Stones
Carving Gouges
Flat Diamond impregnated stones for
honing flat edge tools after sharpening on
the Tormek grinder.
Wood carving tools for removing wood in
a variety of ways depending on the profile
of the gouge. Available in many shapes
and sizes.
Furniture Chisels
Sanding File Set
Fine edged chisels ground to an angle ideal
for joinery and other fine woodwork. To be
used on wood only.
Made of reticulated carbide, these tools are
as coarse as 60 grit sand paper but do not
wear down like sandpaper, and in addition
are stiff like a file. Can be used on foam,
wood, composites, plastics and plaster. Not
for use on metal.
SA nding & S haping
Hand Sanding Pads
Hardened sheet of thin steel with a microhook or burr on the edge. Used as an
alternative, and is in some ways superior
to sand paper on wood. To be used on
wood only.
SA nding & S haping
46
Card Scraper
47
A system for applying pre-glued edgebanding.
Incorporates a heat gun and a roller system for
holding and dispensing the edgeband.
Hot iron for melting and applying electronic solder.
Heat Gun
Soldering Gun
Like a high powered hair dryer. The heat
gun can be used to heat plastics and other
formable materials to low to medium
temperatures or to assist in drying wet
plaster and other air curing materials.
Like a soldering iron with a trigger. Can apply
more heat but can be cantankerous in small
areas where accurate soldering is necessary.
Heating Element
Injection Molder
Long straight heating element in a metal
enclosure can be used to apply localized
heat in a straight line. Great for folding heat
formable plastics along straight seams.
A desktop size machine for heating and
injecting molten plastic into pre-made
injection dyes.
H E AT TO O LS
Soldering Iron
H E AT TO O LS
48
Edge Bander
49
An adhesive administering tool—hot glue
guns heat a solid glue stick to its melting
temperature, which is then extruded from
its tip with the depression of the tool’s
trigger. Though hot glue is a versatile
adhesive, it lacks strength and is thus
inadequate for permanent structures.
A stout sewing machine with a moving presser
foot for sewing thick leathers and stiff canvas
where a presser foot would otherwise impede.
Commercial Sewing Machine
An commercial-strength textile machine used
to stitch fabric or other material together with
thread.
Steam Iron
A heating tool used in combination with
an ironing board to remove wrinkles in
fabric. Requires water for steam ironing.
Fab r ic & P r essing
Walking Foot Sewing Machine
H E AT TO O LS
50
Hot Glue Gun
51
Hearing protective equipment, a suitable
alternative to earplugs.
Safety Glasses, Large
Face Shield
Safe and cool but with more coverage.
A polycarbonate face shield to protect
your vision when working in the shops...
and make you look like Doc from “Back to
the Future”.
Safety Goggles
Protective eyewear which fits well over
prescription eyeglasses.
Safet
y
SA
FETY
Ear Muffs
Safe and cool; what more could you ask?
saic SULLIVAN
hand tool catalogue
SAIC
SHOP
SA nding & S Safet
haping
y
20
52
Safety Glasses
20
53
Attaches to the pneumatic airline. The air
nozzle provides a high pressure blast of
air for blowing off debris or providing a
quick cooldown on a hot summer day.
A gun for spraying high viscosity liquids like
drywall mud. Can be useful for applying a
skim coat to a large or undulating surface
which would otherwise be difficult to coat.
Shop Vacuum
Power Supply
A rugged vacuum that can inhale dust
and larger debris without clogging.
A power source with variable amperage and
voltage. The power supply is used as a testing instrument in the fabrication of electronic
circuitry.
Lathe Chuck
Plaster Bucket
A machining fixture for the wood lathe.
Allows for single ended or face plate turning.
Black rubber bucket in which plaster can be
mixed. Once plaster has dried in the bucket
it is easily removable due to the flexibility
and adhesion resistance of the rubber.
AC C E S S O R I E S
Drywall Mudding Gun
Accesso r ies
54
Air Nozzle
55
Long mixing paddle which chucks into a hand
drill. Used to mix plaster and other liquids.
Handy setup with small mobile clamps
and a magnifying glass for doing detailed
and awkward electronics assembly.
Putty Knife
Vacuum Bag Setup
Flat wide blade for applying and spreading
gooey materials.
A flexible vinyl bag attached to a vacuum
pump. The bag acts like one big flexible
clamp when the bag is sealed shut and the
air removed via the vacuum pump. Can be
used to laminate materials or do
sophisticated bending operations.
Brass Bushing Set
Metal Stretcher (Out)
A system of guide collars used on the
handheld router for template routing or
curve following.
A metalworking tool consisting of two sets
of gripping teeth and a lever. When the lever
is pulled, the teeth clamp down an active
metal part and move away from each other at
a slight radius. Works to stretch thin gauge
metal on an outward radius.
Electronics Stand
56
Plaster Mixer
57
A tool for clearing debris from a files gullets.
Makes a file’s cutting capacity more effective.
Flex Shaft
A fast rotating tool which can be fitted with
carving or polishing burrs. Like a super
Dremel tool.
Glycerin
Used when working with wood veneer.
Spraying veneer with glycerin temporarily
relaxes some veneerss natural stresses
to help flatten it. Can be very useful when
veneering flat materials where it is important
for the veneer to be flat as well.
Hand Truck
A wheeled fixture for moving heavy items.
Can be used on two wheels or as a fourwheeled cart.
y
AC C E S Safet
SORIES
File Card
A metalworking tool consisting of two sets of
gripping teeth and a lever. When the lever is
pulled, the teeth clamp down an active metal
part and move towards each other at a slight
radius. Works to stretch thin gauge metal on
an inward radius.
saic SULLIVAN
hand tool catalogue
SAIC
SHOP
58
Metal Stretcher (In)
20
59
100’ Measuring Tape
Wetzler F Clamp
10
2
Digital Thermometer
2
Air Nozzle
54
Digital Scale
3
Biscuit Jointer
21
Dremel Tool
44
Bits
36-37
Drills
34-36
Paddle Bit Set
36
High Torque Drill
34
Porstner Bit Set
37
Standard Torque Drill
34
Counter Sink Bit
37
Right Angle Drill
35
Brass Brushing Set
56
Pneumatic Drill
35
Corded Drill
35
Calipers
7
Card Scraper
46
Cordless Drill
36
Carving Gouges
47
Drill Bits
36
Chalk Line
Chisels
3
24+46
Drywell Mudding Gun
55
Ear Muffs
53
Chisel Set, Straight
24
Edge Bander
48
Furniture Chisels
46
Electronics Stand
57
Glue Chisels
24
Face Shield
53
Combination Square
4
Compass
7
File Card
59
8–12
Fine File
39
Flat File
39
SAIC sullivan INSTRUCTIONAL SHOP
Clamps
39+59
File
Corner Clamp
Klick Clamp
10
Quick Clamp
12
Glycerin
Spring Clamp
12
Graduated Cylinder
60
Strap Clamp
12
Grommet Tool Set
8
C Clamp
8
F Clamp
10
Grey Uni Clamp
Hand Screw Clamp
K-Body Clamp
8
11
9
2
inde x
31
inde x
18 GA Stapler
28
61
Flat Crowbar
29
Fletcher Blades (4x)
15
Flex Shaft
58
Gauges
6
Bevel Gauge
6
Marking Gauge
6
58
25
Metal Stretcher, In
58
Claw Hammer
25
Metal Stretcher, Out
57
Ball Peen Hammer
25
29
16 GA Nailer
32
Hand Sanding Pads
47
23 GA Pin Nailer
32
Hand Truck
59
Heat Gun
48
Block Plane
40
Heating Element
48
Convex Sole Block Plane
40
Hot Glue Gun
50
Fore Plane
40
Impact Driver
34
Low Angle Block Plane
41
Injection Molder
49
Smoothing Plane
41
Jack Plane
41
Shoulder Plane
42
Irons
49+51
Planes
40-42
Soldering Iron
49
Steam Iron
51
Plaster Bucket
29
11
Plaster Mixer
16
Dowel Drilling Jig
11
Pliers
Pocket Hole Jig
11
Knifes
14-56
29-31
Locking Pliers
30
Needle Nose Pliers
30
Draw Knife
44
Needle Nose Locking Pliers
31
Putty Knife
56
Plat Jaw Pliers
31
Utility Knife
14
Slip Jaw Pliers
29
54
Pneumatic Die Grinder
43
Pneumatic Nipper
20
55
Rubber Mallet
25
Detail Rasp Set
38
Wooden Mallet
24
Rasp
38
Shinto Rasp
39
32
Hand Hold Punch
Jigs
62
Nailers
inde x
inde x
Hammers
28
63
Lathe Chuck
Levels
4-5
Level
4
Power Supply
Torpedo Level
5
Protractors
Mallets
Measuring Tape
Metal Stretchers
24-25
3
57-58
Rasps
Ratchet Set
6
38-39
Riveter/ Pop Rivet Gun
28
Screwdriver
27
Routers
21
Screwdriver Set, Mini
26
21
Trim Router
21
Ruler
Safety Eyewear
inde x
Commerical Sewing Machine
51
Walking Foot Sewing Machine
51
Shaves
38+44
52
Spoke Shave
44
Safety Goggles
52
Surform Shave
38
42-47
Sharpening Stones
46
Belt Sander, Large + Mini
42, 43
Shears
14+17
Palm Sander
42
Metal Shears
14
Pneumatic Orbital Sander
43
Pneumatic Shears
17
Sanding File Set
47
Speed Square
7
15-20
Soldering Gun
49
Staple Gun
30
Tin Snips
17
Saws
Back Saw
19
190
Combination Saw
18
Trammel Compass
5
Coping Saw
18
T-Square
5
Dovetail Saw
14
Vacuums
54+57
Hack Saw
19
Shop Vacuum
54
Hole Saw Set
20
Vacuum Bag Setup
57
Jig Saw
20
Key Hole Saw
15
Corner Vise
9
Pneumatic Hand Saw
22
Drill Vise
9
Pull Saw
18
Wire Stripper
17
16
Wood Carving Set
15
Fabric Scissors
16
Wrenches
Scissors
16
Fixed Wrench Set
27
Utility Scissors
16
Allen Wrench Set
27
Bamboo Saw
52
51
Safety Glasses, Large
Sanders
64
4
Sewing Machines
inde x
Plunge Router
Adjustable Wrench
26
65
Scissors
Screwdrivers
26-27
Vises
9
26-27

*SullivanToolCatalogue

Transcription

Similar documents

kids` triathlon - Decatur Swim Club

K O`Sullivan - kevin o`sullivan + associates

Skate Board Collab Poster

Easter 2014 - Blennerville Primary School Tralee

Sullivan Shwcase Awards.indd - Sullivan County Board of REALTORS

Beautify your barn

PB Nov Garage Used stuff.indd

Schedule - Masson Glennie

Ferrari Carb Mod

James Lowman, Association of Convenience Stores