MITUTOYO - INSIDE MEASURING

Transcription

Precision Measuring Equipment and Industrial Supplies since 1924.
www.jwdonchin.com
4841 W. Chicago Ave. • Chicago, IL 60651 • Ph: 773.261.2182 • Fax: 773.261.2867 • [email protected]
MITUTOYO - INSIDE MEASURING INSTRUMENTS
INSIDE MEASURING INSTRUMENTS
Inside Micrometers - Series 345, 145
Inside Micrometers - Series 141 - Interchangeable Type
Tubular Inside Micrometers - Series 337, 137 - Extension Type
Tubular Inside Micrometers - Series 339, 139, 140 - Heavy Duty Type
Tubular Inside Micrometers - Series 133
Digimatic Bore Gages - Series 511
Dial Bore Gages - Series 526 - Split-Ball Type
Dial Bore Gages - Series 511
Dial Bore Gages with Micrometer Heads - Series 511
Dial Bore Gages - Series 511 - For Shallow Holes
Holtests - Series 368 - Two Point Models
Holtests - Series 368 - Interchangeable Anvil Type
Digimatic Holtests - Series 468 - Complete Unit Sets
Dial Bore Gages - Series 545 - Rugged, Production-Line Tools
Borematic with Absolute Encoder - Series 568
Setting Rings - Series 177
MSG/MLS Air Gaging Models
Chamfer Chek - Series 526
Digimatic Chamfer Chek - Series 547
Hole Chek - Series 526 - Instant Dia. Meas. of Small Holes
N-2,3
N-4.5
N-6, 7
N-8, 9
N-10,11
N-12,13
N-14,15
N-16,17
N-18,19
N-20
N-21,22
N-23~25
N-26~29
N-30
N-31,32
N-33
N-34
N-35
N-36
N-37
N-02 (2003) full size
12/8/03
7:18 PM
Page 1
INSIDE MICROMETERS
Inside Micrometers
Series 345, 145
T
EC
345-711-30
OG
Y
AB
LUT
SO E
H N OL
145-187
300401 Cap
145-193
300400 Holder
145-193
A special holder is available for inside micrometers.The holder must be used with No.156-101
MITUTOYO Stand or any other similar stand or
vise available in the shop.
Features
•
•
•
•
Accuracy to .0002" with graduations of .001".
Easy zero adjustment.
Clear graduations on satin-chrome finish.
Caliper type jaws are made of high-grade, tool steel.
They are satin-chrome finished.
• Locking clamp for positive locking of spindle.
• With ratchet thimble for constant force.
•
•
•
•
•
Every thousandth is numbered for easy reading.
Easily adjusted for slide movement of jaw (Exclusive.)
Spanner wrench is supplied with every micrometer.
Complete with fitted carrying case.
Digimatic type features LCD Readout, Preset,
Zero/ABS, Data/Hold, Inch/mm and SPC Output.
Specifications
Digimatic Inside Micrometers with Absolute Encoder
Inch/Metric
Order No.
345-711-30
345-712-30
LCD
Range
.2"–1.18"
5–30mm
1.0"–2.0"
25.4-50.8mm
Resolution
.00005"
0.001mm
.00005"
0.001mm
Accuracy
±.0002"
Remarks
with SPC output
±.00025"
with SPC output
Metric
Order No.
Range
Resolution
Accuracy
Remarks
5–30mm
0.001mm
±0.005mm
with SPC output
345-511-30
345-512-30
25–50mm
0.001mm
±0.006mm
with SPC output
Note: Metric only Digimatic models have mm thimble and no inch/mm conversion function.
For SPC output order Connecting Cable 937387 (1m) or 965013 (2m). Replacement Battery: 541980 (1pc), 541980-10 (10pcs/SET).
N-2
12/8/03
7:20 PM
Page 1
INSIDE MICROMETERS
Inside Micrometers
Inch
Order No.
145-193
145-194
145-195
145-196
Range
.2"–1.18"
1.0"–2.0"
2.0"–3.0"
3.0"–4.0"
Resolution
.001"
.001"
.001"
.001"
Accuracy
±.0002"
±.00025"
±.0003"
±.00035"
Remarks
Measuring
Measuring
Measuring
Measuring
Face: A
Face: B
Face: C
Face: C
Range
5–30mm
25–50mm
50–75mm
75–100mm
Resolution
0.01mm
0.01mm
0.01mm
0.01mm
Accuracy
±0.005mm
±0.006mm
±0.007mm
±0.008mm
Remarks
Measuring
Measuring
Measuring
Measuring
Face: A
Face: B
Face: C
Face: C
Metric
Order No.
145-185
145-186
145-187
145-188
Measuring Face: A
.2"
ø.079"
ø.079"
R .087"
1.08"
.18"
R .087"
Measuring Face: C
Measuring Face: B
.37"
R.47"
.37"
.17"
.17"
R.47"
.49"
(.2" to 1.18")
.079"
.079" (Diameter)
(R=.087")
Carbide Pins
Carbide Inlaid
(R=.48")
.12"
.315"
.1.3"
.079"
.315"
(1.0" to 2.0")
.48"
.118"
1.26"
.118"
Digimatic Type Range 1–2"
(25–50mm)
.177"
.177"
Digimatic Type Range .2–1.18"
(5–30mm)
.69"
1.08"
.49"
1.08"
1.24"
N-3
12/8/03
7:22 PM
Page 1
INSIDE MICROMETERS
Inside Micrometers
Series 141 – Interchangeable Type
141-233
The 141 Series Inside Micrometers are probably the most
frequently used inside measuring instruments because of
their wide range and simplicity in measuring operation.
No. 141-233, (photo shown), consists of 5 interchangeable
rods, .500" micrometer head, .500" collar 1" extension
and handle. The range covered by this unit is 2" to 12".
141-102
141-101
To provide point contact, all contact points are made
spherical and hardened for extra long tool life. The overall
accuracy is .0004" up to 12" (300mm), .001" thereafter to
40".
Features
• Each interchangeable rod is marked with its measuring
range.
• Both micrometer head and furnished rods are satinchrome finished throughout.
• Positive locking clamp attached on No. 141-101 and
141-102. No lock on the larger sizes.
• Supplied with fitted carrying case.
For closer tolerance work it is recommended that the
micrometer with a rod inserted be calibrated with a
known size such as a ring gage. The setting ring for
“Holtest” would be an ideal choice.
No. 141-102
As shown here, the Micrometer Head has a 0–.250"
range, reading in thousandths. A detachable holder provides easy access when measuring inside diameters
within deep holes. For 1" to 1.250" range, the micrometer
N-4
is used without the rod or collar.
For 1.250" to 1.500" a .250" collar is added between the
rod and head. For 1.500" to 1.750" range, the rod is
replaced. For 1.750" to 2", the collar is added between
the rod and head. Thus, it measures 1" to 2"–.250" at a
time.
No. 141-233
Since this Inside Micrometer comes with a .500" range
Micrometer Head, the combining of rod, collar and
extended thimble is made simpler. For instance: the rod
marked 4–6" measures from 4"–4.5". For 4.5–5" range,
the .500 collar is added. For 5"–5.5" the extension thimble is used and for 5.5" to 6" the extension thimble and
collar are used.
Both measuring ends are hardened and have microlapped finish for lasting accuracy.
12/8/03
7:24 PM
Page 1
INSIDE MICROMETERS
Specifications
Inside Micrometers—Interchangeable Rod Type
Inch
Order No.
141-102
141-208
141-233
141-121
141-122
Range
1–2"
2–8"
2–12"
8–20"
8–40"
Spacing
Collar
.250"
.500"
.500"
1", 2"
1", 2"
Diameter
of Rods
.248"
.248"
.248"
.355"
.355"
Remarks
Includes 141-002 and 2 pcs rods
Includes 141-026, 3 rods and 1" extended thimble
Includes 141-026, 5 rods and 1" extended thimble
Range
25–50mm
50–200mm
50–300mm
200–500mm
200–1000mm
Spacing
Collar
6.0mm
12.0mm
12.0mm
25mm, 50mm
25mm, 50mm
Diameter
of Rods
6.3mm
6.3mm
6.3mm
9.0mm
9.0mm
Remarks
Includes 141-025, 3 rods and 25mm extended thimble
Includes 141-025, 5 rods and 25mm extended thimble
Metric
Order No.
141-101
141-205
141-206
141-117
141-118
Micrometer Heads
Inch
Order No.
141-002
141-026
141-010
Head Travel
.25"
.50"
1.00"
Resolution
.001"
.001"
.001"
Accuracy
±.0001"
±.0001"
±.0001"
Head Travel
7.0mm
13.0mm
25.0mm
Resolution
0.01mm
0.01mm
0.01mm
Accuracy
±0.003mm
±0.003mm
±0.003mm
Metric
.54"
(13.7)
ø.16" (ø4) hole
.2"
(5)
ø.2"
(ø15)
.24"
(6.2)
.35"
.45"
(8.8) (11.5)
.07"
(1.8)
ø.26"
(ø6.5)
ø.47"
(ø12)
.05"
(1.2)
1.71" (43.5)
.91"
(23)
ø.59"
(ø15)
Order No.
141-001
141-025
141-009
SR .39"
(SR10)
141-026
(METRIC)
141-001
N-5
12/8/03
7:26 PM
Page 1
INSIDE MICROMETERS
Tubular Inside Micrometers
Series 337, 137 – Extension Type
337-203
137-102
Features
• Wide range of ID measurements by combining
extension rods with the micrometer head. The rod
is accurately finished and incorporated in a pipe for
shop-floor use.
• The 337 series provides digital readout to
.0001"/0.001mm and can be linked to the SPC System.
• Digimatic Function Include:
Preset
Inch/mm conversion
Zero-Set/ABS
Hold
Data Output
• Power Supply:
One Silver oxide cell (SR-44), offers 4,500 hours of life
• The display automatically turns off if idle after 20 minutes.
Accuracy
• Series 137, 337:
[±(.00015+.00005n+.00005 (L/2))"]*/±(3+n+L/50)µm
*n=Number of rods, L=Maximum measuring length [(inch)] (mm),
Fraction rounded up
Specifications
Digimatic Inside Micrometers
Inch/Metric
Order No.
337-203
Range
8–40"
LCD
Resolution
.0001"/0.001mm
Head
Travel
1.0"
Extension Rods
(Dia .50")
1", 2", 4" (2 pcs.)
8", 12"
Remarks
Includes Micrometer
Head with SPC output.
337-204
8–60"
.0001"/0.001mm
1.0"
1", 2", 4", 8"
12" (3 pcs.)
Includes Micrometer
Head with SPC output
For SPC output order Connecting Cable 937387 (1m) or 965013 (2m).
Replacement Battery: 541980 (1 pc.), 541980-10 (10 pcs. SET)
N-6
12/8/03
7:28 PM
Page 1
INSIDE MICROMETERS
Inside Micrometers
Inch
Order No.
137-112
137-114
Range
2–12"
2–40"
Extension Rods
(Diameter .50")
.5", 1", 2"(2pcs), 4"
.5", 1", 2", 4"(2pcs), 6", 8", 12"
Range
50–300mm
50–1000mm
50–500mm
Extension Rods
(Diameter 12.5mm)
13, 25, 50(2pcs), 100mm
13, 25, 50, 100(2pcs), 150, 200, 300mm
13, 25, 50(2pcs), 100, 200mm
Remarks
Include 137-002
Include 137-002
Metric
Order No.
137-102
137-104
137-108
Remarks
Include 137-001
Include 137-001
Include 137-001
Rods with Carbide-tipped Measuring Face
Micrometer Heads
Inch
Order No.
137-002
Head Travel
.50"
Resolution
.001"
Accuracy
±.0001"
Head Travel
13.0mm
Resolution
0.01mm
Accuracy
±0.003mm
Metric
Order No.
137-001
137-002
Included in Set Nos. 337-203 and 337-204.
N-7
12/8/03
7:30 PM
Page 1
INSIDE MICROMETERS
Series 339, 139, 140 – Heavy Duty Type
339-293
139-179
Features
Accuracy
• Wide range of ID measurements by combining extension pipes and anvils with the micrometer head.
.0001"/0.001mm and can be linked to the SPC System.
• Pipe diameter
139 series: .67"/17mm
140 series: 1.26"/32mm
• For higher repeatability of measurement, light weight
extension pipes made of CFRP (Carbon Fiber
Reinforced Plastic) for 139 Series.
• Digimatic Functions Include:
Preset
Inch/mm conversion
Zero set/ABS
Hold
Data output
• Power Supply: One silver oxide cell
(SR-44) offers 4,500 hours of life
• The display automatically turns off idle after 20 minutes
• Series 139, 339:
[±(.00015+.00005n+.00005 (L/2))"]/±(3+n+L/50)µm*
• Series 140:
[±.(0003+.00005n+.00005 (L/2))"]/±(7+n+L/50)µm*
*n=Number of rods, L=Maximum measuring length [(inch)] (mm),
Fraction rounded up
Specifications
Inch
Order No.
139-201
139-202
Range
1.5–12"
4–40"
Diameter
of Rods
.375"
.375"
Extension
Rods
.5", 1", 2", 2.5", 3", 3.5", 4", 6"
1", 2", 3", 6", 9", 12", 14", 16", 17", 18"
Remarks
Include 139-004
Include 139-006
Specifications
Digimatic Inside Micrometers (Series 339)
Inch/Metric
LCD
Head
Diameter
Resolution
Travel
of Rods
.0001"
1.0"
.67"
0.001mm
339-294
8–80"
.0001"
1.0"
.67"
0.001mm
For SPC output order Connecting Cable 937387 (1m) or 965013 (2m).
Replacement Battery: 541980 (1 pc.), 541980-10 (10 pcs./SET)
Order No.
339-293
N-8
Range
8–40"
Remarks
Include Micrometer Head and 5 pcs rods
with SPC output
Include Micrometer Head and 8 pcs rods
with SPC output
12/8/03
7:31 PM
Page 1
INSIDE MICROMETERS
Inside Micrometer Heads
Inch
Order No.
139-002
139-004
139-006
Head Travel
1.0"
.50"
1.0"
Resolution
.001"
.001"
.001"
Accuracy
±.00015"
±.00015"
±.00015"
Head Travel
25.0mm
Resolution
0.01mm
Accuracy
±0.003mm
Metric
Order No.
139-001
Inside Micrometers (Series 139)
Inch
Order No.
139-178
139-179
139-180
Extension Rods
(Diameter .67")
1", 2", 4", 8"
1", 2", 4", 8", 16"
1", 2", 4", 8", 16"(2pcs.)
Range
4–20"
4–36"
4–52"
Remarks
Include 139-002
Include 139-002
Include 139-002
Inside Micrometers (Series 140)
Inch
Head
Travel
2.0"
2.0"
2.0"
Resolution
.001"
.001"
.001"
Extension Rods
(Diameter 1.26")
2", 4"(2pcs.), 8", 20", 40"
2", 4"(2pcs.), 8", 20", 40"(2pcs.)
2", 4"(2pcs.), 8", 20", 40"(3pcs.)
139-002
139-004
Included in Set Nos. 339-293
and 339-294.
139-006
100 to 125
50
8
11 1.5
23
4.8
Ø15
1.7
4.5
2.5
15
25
3
139-001
Ø33
16.5
Ø8
Ø32
Ø19
SR10
SR10
SR10
137-001
Ø33
Ø8
3
Ø18
Ø4
Ø4
SR10
SR10
47
3
Ø4
1
M10x1
Remarks
Include Micrometer Head
Ø4
Range
40-120"
40-160"
40-200"
175.5
699
1000 to 1050
Ø21
Order No.
140-162
140-163
140-164
101
15
SR10
Micrometer Head for series 140
N-9
12/8/03
7:14 PM
Page 1
INSIDE MICROMETERS
Series 133
133-223
133-224
133-225
133-226
Features
• Accuracy up to 4"
±.00015"
4–6"
±.0002"
6–12" ±.0003"
• With positive locking clamp.
• Zero point can be readjusted by twisting the micrometer
head sleeve. A key wrench is supplied.
• 2–6" set and 2–12" set are available.
• Clear, crisp graduations on the satin chrome finished
micrometer head.
• Carbide tipped measuring faces.
• Supplied in a carrying case.
Specifications
Metric
Inch
Order No.
133-223
133-224
133-225
133-226
133-227
133-228
133-229
133-230
133-231
133-232
Range
2–3"
3–4"
4–5"
5–6"
6–7"
7–8"
8–9"
9–10"
10–11"
11–12"
Resolution
.001"
.001"
.001"
.001"
.001"
.001"
.001"
.001"
.001"
.001"
Accuracy
±.00015"
±.0002"
±.00025"
±.00025"
±.00025"
±.00025"
±.00025"
±.0003"
±.0003"
±.0003"
Order No.
133-143
133-144
133-145
133-146
133-147
133-148
133-149
133-150
133-151
133-152
Range
50-75mm
75-100mm
100-125mm
125-150mm
150-175mm
175-200mm
200-225mm
225-250mm
250-275mm
275-300mm
Resolution
0.01mm
0.01mm
0.01mm
0.01mm
0.01mm
0.01mm
0.01mm
0.01mm
0.01mm
0.01mm
Tubular Inside Micrometer Sets
Inch
Tubular Inside Micrometer Sets
Metric
Order No.
133-903
Order No.
133-901
133-904
N-10
Total Range
2–6"
(4 Mikes/set)
2–12"
(10 Mikes/set)
Set Configuration
133-223, 224, 225, 226
with fitted case
133-223, 224, 225, 226,
227, 228, 229, 230, 231, 232
with fitted case
133-902
Total Range
50-150mm
(4 Mikes/set)
50-300mm
(10 Mikes/set)
Accuracy
±3 µm
±4 µm
±5 µm
±5 µm
±5 µm
±5 µm
±5 µm
±6 µm
±6 µm
±6 µm
Set Configuration
133-143, 144, 145, 146
with fitted case
133-143, 144, 145, 146,
147, 148, 149, 150, 151, 152
with fitted case
12/8/03
7:17 PM
Page 1
INSIDE MICROMETERS
Series 133
DIMENSIONS (inch)
L
B
.12"
.12"
.59"
.59"
.59"
.59"
.59"
.59"
A
B
1.85"
(47)
ø.315"
(ø8)
A
.15"
.14"
.65"
.61"
.61"
.61"
.61"
.61"
.71" (ø18)
L
4"
5"
6"
7"
8"
9"
10"
11"
ø.315"
(ø8)
Order No.
133-225
133-226
133-227
133-228
133-229
133-230
133-231
133-232
R=.394"
(SR10)
R=.394"
(SR10)
1.97"
(50)
.12"
(3)
ø.315"
(ø8)
1.45"
(37)
ø.59"
ø.315"
(ø8)
.14"
(3.5)
L
100
125
150
175
200
225
250
275
A
3.8
3.5
16.5
15.5
15.5
15.5
15.5
15.5
B
3
3
15
15
15
15
15
15
ø.315"
(ø8)
Order No.
133-145
133-146
133-147
133-148
133-149
133-150
133-151
133-152
R=.394"
(SR10)
ø.59"
DIMENSIONS (metric)
133-143
133-223
ø.315"
(ø8)
R=.394"
(SR10)
1.45"
(37)
.14"
(3.5)
R=.394"
(SR10)
2.95"
(75)
R=.394"
(SR10)
133-144
133-224
(mm)
N-11
12/9/03
9:52 AM
Page 1
BORE GAGES
Digimatic Bore Gages
Series 511
Features
• .00012” (0.003mm) or less wide range accuracy
• Anvil displacement is directly detected by the ultra
compac built-in sensor (no mechanical transmitter is used)
• Maximum extension up to 78.74” (2000mm)
• Reaches deep holes easily!
• Simple to operate – can preset 3 reference (master) value
and set upper/lower tolerance limits for each!
• IP53 dust/water protection level
Specifications
Order No.
Range
Contact Point Stroke
Resolution
Wide range accuracy
Narrow range accuracy
Repeatability
Quantizing error
Measuring force
Battery (541980)
Battery Life
Sensor/scale
Sampling frequency
Protection level
Data output
Mass
511-521
1.8" - 4" (45 - 100mm)
.048" / 1.2mm
.00005" / 0.001mm
.00012" / 0.003mm
.00008" / 0.002mm
±1 count
±1 count
5N or less
Silver oxide cell (SR-44–2 pcs.)
9 months under normal use
Electrostatic capacitance
absolute scale
50 times / sec
IP53
SPC data output
1.1 lbs. / 500g
Standard Accessories
Anvils
14 pcs.
Spacer
4 pcs. .02", .04", .08", .12"
Hex Wrench
1 pc.
Optional Accessories
905338
SPC Cable 40"/1m
905409
SPC Cable 80"/2m
21DZA089
Extension Rod 9.84"/250mm
21DZA081
Extension Rod 19.69"/500mm
516-120-22
Measuring Size set
Gage Block Set
N-12
Specifications
Order No.
516-120-22
Set of:
Steel Rectangular gage Block
.04", .08", .16", .2", .4", .8", 1", 2", 3"
Flat Jaw (619970) 2 pcs.
Holder 160mm (619004) 1 pc.
Wooden Box
12/8/03
7:21 PM
Page 1
BORE GAGES
Digimatic Bore Gages
Series 511
Dimensions
rotation
(320°)
1.157"
29.4
RESET sw
M/W sw
inclination (90°)
"
ø2.402
ø61
For inch-readable model
ø1.102"
ø28
PRESET sw
5.906"
150
1.181"
30
10.571" (20.413")
268.5 (518.5)
.787"
20
ø.866"
ø22
ø 1.181"
ø 30
9.134" (18.976")
232 (482)
(13.366")
(339.5)
9.843" ( 19.685")
250 (500)
3.937"
100
rotation
(320°)
M26x1.5
.65"
16.5
5.906"
150
START sw
1.102"
28
ø1.102"
.059"
1.5
DATA/HOLD sw
ON/OFF in/mm sw
TOL sw
28
( ):for 19.685"/500mm type
2
SR 79"
0
.
R
.354"
9
2
SR 79"
0
R.
1.339"
34
N-13
12/8/03
7:23 PM
Page 1
BORE GAGES
Dial Bore Gages
Series 526 – Split-Ball Type
526-173
Optional Stand
(215-120M)
Probe Depth (L)
526-120
Features
• Measures diameters of small holes.
• Radius displacement of split-ball contact is converted to
axial displacement of measuring pin, which is shown on
the dial indicator.
• Digimatic Indicator can be installed in place of the dial
indicator.
• Accuracy: .00016"/4µm (Range: .037–.4"/0.95–10mm)
.00024"/6µm (Range: .4–.7"/10–18mm)
• Optional stand (215-120) for Bore Gages Series 526
is available for efficient measurement of multiple
small holes.
Specifications
Dial Bore Gages
Inch
Order No.*
Without Dial
Gage
Order No.
With 2922FB
Graduation .0005"
526-103
526-119
526-104
526-120
*Does not include dial gage cover.
Order No.
With 2923FB-10
Graduation .0001"
Measuring
Range
Number of
Anvils
Probe
Depth
526-122
526-123
.3"-.4"
.4"-.7"
6 pcs.
8 pcs.
2.2"
2.4"
Order No.
With 2109FB
Graduation .0.001mm
Measuring
Range
Number of
Anvils
Probe
Depth
526-124
526-125
7-10mm
10-18mm
6 pcs.
8 pcs.
56mm
62mm
Metric
Order No.*
Without Dial
Gage
Order No.
With 2046FB
Graduation 0.01mm
526-101
526-126
526-102
526-127
N-14
12/8/03
7:25 PM
Page 1
BORE GAGES
Specifications
Dial Bore Gages
Split-Ball Type
Inch
Order No.*
Without
Dial Gage
526-175
526-165
526-155
Order No. with
2923FB-10
Graduation .0001"
526-176
Measuring
Range
.037"–.061"
526-166
.060"–.157"
526-156
.145"–.290"
Probe
No.
1.0
1.1
1.2
1.3
1.4
1.75
2.00
2.25
2.50
2.75
3.00
3.25
3.50
3.75
4.0
4.5
5.0
5.5
6.0
6.5
7.0
Anvil
Range
Length
.037"–.045"
.042"–.049"
.046"–.053"
.050"–.057"
.054"–.061"
.060"–.075"
.070"–.085"
.080"–.095"
.090"–.105"
.100"–.115"
.110"–.125"
.120"–.135"
.130"–.145"
.140"–.157"
.145"–.170"
.165"–.190"
.185"–.210"
.205"–.230"
.225"–.250"
.245"–.270"
.265"–.290"
.45"
.69"
.89"
1.26"
Setting Ring
Code No.
Size
177-220
177-222
177-225
177-227
177-230
177-236
177-239
177-242
177-208
177-246
177-248
177-250
177-252
177-255
177-204
177-257
177-205
177-263
177-267
177-271
177-275
No. of
Needle
.04"
.045"
.05"
.055"
.06"
.07"
.08"
.09"
.10"
.11"
.12"
.13"
.14"
.15"
.16"
.18"
.20"
.22"
.24"
.26"
.28"
1
2
1
Metric
Order No.* Order No. with
Without
2046FB
Dial Gage Graduation
0.01mm
526-170
526-160
526-150
526-173
526-163
526-153
Order No. with Measuring
2109FB
Range
Graduation
0.001mm
526-172
526-162
526-152
0.95–1.55mm
1.5–4mm
3.7–7.3mm
Probe
No.
1.0
1.1
1.2
1.3
1.4
1.75
2.00
2.25
2.50
2.75
3.00
3.25
3.50
3.75
4.0
4.5
5.0
5.5
6.0
6.5
7.0
Anvil
Range
0.95–1.15mm
1.07–1.25mm
1.17–1.35mm
1.27–1.45mm
1.37–1.55mm
1.50–1.90mm
1.80–2.20mm
2.05–2.45mm
2.25–2.75mm
2.50–3.00mm
2.75–3.25mm
3.00–3.50mm
3.25–3.75mm
3.50–4.00mm
3.7–4.3mm
4.2–4.8mm
4.7–5.3mm
5.2–5.8mm
5.7–6.3mm
6.2–6.8mm
6.7–7.3mm
Length
(mm)
11.5
17.5
22.5
32
Setting Ring
Code
Size
(mm)
No.
177-220
177-222
177-225
177-227
177-230
177-236
177-239
177-242
177-208
177-246
177-248
177-250
177-252
177-255
177-204
177-257
177-205
177-263
177-267
177-271
177-275
1.0
1.1
1.2
1.3
1.4
1.75
2.00
2.25
2.50
2.75
3.00
3.25
3.50
3.75
4.0
4.5
5.0
5.5
6.0
6.5
7.0
No. of
Needle
1
2
1
Above sets include setting rings.
*Does not include Dial gage cover.
N-15
12/8/03
7:27 PM
Page 1
BORE GAGES
Dial Bore Gages
Series 511
Type of Measuring Head
511-162
511-212
.24–.4"
.4"–.74"
10–18.5mm
.7"–2.4"
18–60mm
2.0"–16.0"
50–400mm
Features
• Interchangable anvils and necessary accessories to
perform close tolerance I.D. measurements.
• Carbide ball contact point for durability.
• Optional extension rods can be attached.
• A Digimatic Indicator can be attached in place of the
dial gage.
• Accuracy: .0002"/5µm
Dial Faces
+ 0 _
5
5
.0005"
10
10
NO. 2922-08
15
1
0
20
2 3
25
2922FB
.0005"
N-16
®
PROOF
SHOCK
MADE
IN
+ 0 _
1
JAPAN
20
15
1
30
3
.0001"
2
1
0
3
2
3
2
6
JEWELS
5
5
4
2923FB-10
.0001"
_0+
0 10
1
3
2
20
1µm
1µm
40
4
60
6
707
4
1
10
50
5
®
4
20
2
808
.6 .4
.8
.2
1.0
10 0
0
.2
.8
.4 .6
4
40
NO.1011-11
NO. 2109FB ®
E ELLES D
6J E W
JEW
909 100
10 909
7
70
8
80
2109FB
0.001mm
80
70
10
20
0.01"
5
50
6
60
MADE IN JAPAN
0
90
3
30
1
0
Shock
9
2
8
3
7
4
60
5
6
50
40
2046FB
0.01mm
30
12/8/03
7:29 PM
Page 1
BORE GAGES
Specifications
Dial Bore Gages
Inch
Order No.*
Without
Dial Gage
511-214
511-205
511-104
511-105
511-107
Order No.
With 2922FB
Graduation .0005"
511-213
511-207
511-159
511-160
511-162
Order No.
With 2923FB-10
Graduation .0001"
511-212
511-206
511-163
511-164
511-166
Measuring
Range
Number
of Anvils
Number
of Spacers
Probe
Depth
.24"-.4"
.4"-.74"
.7"-1.4"
1.4"-2.5"
2"-6"
1
3
4
4
2"
4"
4"
6"
6"
511-181
511-182
511-183
511-184
511-185
511-186
511-911 (set)
511-187
511-188
511-189
511-912 (set)
4"-6.5"
6.5"-10.0"
10.0"-16.0"
.7"-6.0"
9 pcs.
9 pcs.
8 pcs.
6 pcs.
11 pcs.
2" Sub-Anvil
13 pcs.
6 pcs.
5 pcs.
25 pcs.
2" Sub-anvil
4
6
6
7
6"
10"
10"
4", 6"
Metric
Order No.*
Without
Dial Gage
511-201
511-126
511-127
511-128
511-132
Order No.
With 2046FB
Graduation 0.01mm
511-204
511-171
511-172
511-173
511-174
Order No.
With 2109FB
Graduation 0.001mm
511-203
511-167
511-168
511-169
511-170
Measuring
Range
Number
of Anvils
Number
of Spacers
Probe
Depth
10-18.5mm
18-35mm
35-60mm
50-100mm
50-150mm
1
2
4
4
4
90mm
100mm
150mm
150mm
150mm
511-129
511-130
511-131
511-175
511-176
511-177
511-901 (set)
511-178
511-179
511-180
511-902 (set)
100-160mm
160-250mm
250-400mm
18-150mm
9 pcs.
9 pcs.
6 pcs.
11 pcs.
11 pcs.
50 mm Sub-anvil
13 pcs.
6 pcs.
5 pcs.
26 pcs.
50mm Sub-anvil
4
7
7
7
150mm
250mm
250mm
100mm
150mm
Extension Rods
Bore Gage
Extension Length
Measuring
4.92"
9.84"
19.69"
29.53"
Range
125mm
250mm
500mm
750mm
.7–1.4"
953549
953550
953551
––
18–35mm
953552
953553
953554
953555
1.4–6.5"
35–160mm
953557
952361
953558
953559
6.5–16"
160–400mm
Note: Above list is used for 511-1XX series; not available for 511-2XX Series.
39.37"
1000mm
––
953556
953560
Rod
Diameter
.34"
8.7mm
.47"
12mm
.59"
15mm
Spanner
102148A
212556
212556
N-17
12/8/03
7:31 PM
Page 1
BORE GAGES
Dial Bore Gages with Micrometer Heads
Series 511
511-319
Probe Depth
Ring gages offer the best
method of zero setting Dial
Bore Gages.
Extension Rod
Features
• Interchangeable anvil is attached to a micrometer head
for accurate dimensional setting.
• Carbide ball contact point for durability.
• Measuring range can be expanded by attaching a
sub-anvil.
N-18
• Optional extension rods can be attached.
dial gage.
12/8/03
7:32 PM
Page 1
BORE GAGES
Specifications
Dial Bore Gages with Micrometer Heads
Inch
Order No.*
Order No.
Without
With 2922FB
Dial Gage
Graduation .0005"
511-342
511-345
511-332
511-335
511-306
511-325
511-307
511-319
511-308
511-321
511-309
511-323
511-310
511-329
Order No.
With 2923FB-10
Graduation .0001"
511-346
511-336
511-326
511-320
511-322
511-324
511-330
Measuring
Range
Mike Head
Travel
Extensions
Mike Head
Probe
Depth
1.4-2.5"
2.4-4.0"
4.0-6.0"
6.0-10.0"
10.0-16.0"
16.0-24.0"
24.0-32.0"
.2"
.4"
.5"
1"
2"
2"
2"
.2", .4", .6", .8"
.4", .8"
.4", .8", .8"
1", 2"
2", 2"
2", 4"
2", 4"
6"
6"
6"
10"
10"
10"
10"
Probe
Depth
Metric
Order No.*
Without
Dial Gage
511-341
Order No.
With 2046FB
Graduation 0.01mm
511-344
Order No.
With 2109FB
Graduation 0.001mm
511-343
Measuring
Range
Mike Head
Travel
Extensions
Mike Head
35-60mm
5mm
511-331
511-301
511-334
511-312
511-333
511-311
60-100mm
100-160mm
10mm
13mm
5mm, 10mm
15mm, 20mm
10mm, 20mm
10mm, 20mm,
20mm
25mm, 50mm
50mm, 50mm
50mm, 100mm
50mm, 100mm
511-302
511-314
511-303
511-316
511-304
511-318
511-305
511-328
511-313
511-315
511-317
511-327
150-250mm
250-400m
400-600mm
600-800mm
25mm
50mm
50mm
50mm
150mm
150mm
150mm
250mm
250mm
250mm
250mm
Extension Rods
Bore Gage
Measuring
4.92"
9.84"
Range
125mm
250mm
1.4-2.5"
953549
953550
35–60mm
953552
953553
2.4–6.4"
60–160mm
953557
952361
6.0–32.0"
150–800mm
Note: Above list is used for 511-3XX Series.
Extension Length
19.69"
500mm
953551
29.53"
750mm
––
39.37"
1000mm
––
953554
953555
953556
953558
953559
953560
Rod
Diameter
.34"
8.7mm
.47"
12mm
.59"
15mm
Spanner
102148A
212556
212556
N-19
12/8/03
7:16 PM
Page 1
BORE GAGES
Dial Bore Gages
Series 511
For Shallow Holes
Features
6" (150mm)
511-442
Probe Depth
511-431
• Can measure ID at position close to the bottom of
blind holes.
dial gage.
Specifications
Dial Bore Gages
Inch
Order No.*
Without Dial
Gage
Order No.
With 2922FB
Graduation .0005"
511-406
511-431
511-407
511-432
511-408
511-433
511-409
511-434
Order No.
With 2923FB-10
Graduation .0001"
Measuring
Range
Number of
Anvils
Number of
Spacers
511-441
511-442
511-443
511-444
.6-1.4"
1.4-2.4"
2.0-4.0"
2.0-6.0"
11 pcs., .4" Sub-anvil
6 pcs.
11 pcs.
11 pcs., 2" Sub-anvil
1
4
4
4
Order No.
With 2109FB
Graduation 0.001mm
Measuring
Range
Number of
Anvils
Number of
Spacers
15-35mm
35-60mm
50-100mm
50-150mm
11 pcs., 10mm Sub-anvil
6 pcs.
11 pcs.
11 pcs., 50mm Sub-anvil
1
4
4
4
Metric
Order No.*
Without Dial
Gage
Order No.
With 2046FB
Graduation 0.01mm
511-401
511-411
511-421
511-402
511-412
511-422
511-403
511-413
511-423
511-404
511-414
511-424
Extension rods are not available for 511-4XX Series.
N-20
12/8/03
7:17 PM
Page 1
HOLTESTS
Holtests
Series 368 – Two Point Models for Very Small Holes
368-022
368-023
368-024
368-025
To read ID’s to .0001" directly, the probe movement is
designed to assure consistent accuracy over the entire
range. The probe movement fixes one side of the probe
and allows the other half of the probe to move parallel
to the stationary side. With this new design and the leafspring mechanism, these Holtests are, by far, the most
direct and accurate instruments to check small hole
diameters.
Accuracy
Inch Type
Metric Type
.00008"
0.002mm
Measuring Force (per Anvil)
4–20N
Specifications
Holtests–Two Point Models
Inch
Set Order No.
368-926
368-927
Range
.080–.100"
.100–.120"
.120–.160"
.160–.200"
.200–.240"
.240–.280"
Individual
Order No.
368-021
368-022
368-023
368-024
368-025
368-026
Grad.
.0001"
.0001"
.0001"
.0001"
.0001"
.0001"
L1
.47"
.47"
.86"
.86"
.86"
.86"
L2
4"
4"
4.5"
4.5"
4.5"
4.5"
Range
2–2.5mm
2.5–3mm
3–4mm
4–5mm
5–6mm
Individual
Order No.
368-001
368-002
368-003
368-004
368-005
Grad.
0.001mm
0.001mm
0.001mm
0.001mm
0.001mm
L1
12mm
12mm
22mm
22mm
22mm
L2
104mm
104mm
114mm
114mm
114mm
Accessories
Included In Set
177-209 Setting Ring .100" Dia.
202863 Hex Wrench
202863 Hex Wrench
Metric
Set Order No.
368-906
368-907
Accessories
Included in Set
177-208 Setting Ring 2.5mm Dia.
202863 Hex Wrench
177-204 Setting Ring 4mm Dia.
177-205 Setting Ring 5mm Dia.
202863 Hex Wrench
N-21
12/8/03
7:19 PM
Page 1
HOLTESTS
Holtests
Series 368
368-201
368-103
These Holtests are versatile, three-point
internal micrometers for the accurate and
efficient direct-measurement of internal
diameters. Three anvils, evenly spaced at
120° apart, contact the internal wall surfaces and find true alignment with the axis
of the bore for accurate ID measurement.
Extension Rods (optional)
Application range
Inch
Metric
.275–.5"
6–12mm
.5–.8"
12–20mm
.8–1.2"
20–30mm
1.2–4.4"
30–110mm
Order No.
952322
952621
952622
952623
Length
3.94"(100mm)
5.9" (150mm)
5.9" (150mm)
5.9" (150mm)
Features
• Measurement can be taken nearly up to
the bottom of the bore.
• Highly durable because of carbide tipped
contact points.
• Can measure deep holes using an extension rod which is available on models
over 6mm measuring range.
• Ratchet stop for constant measuring
force.
Accuracy
Range
.275–.8"
6–20mm
.8–4"
20–100mm
4–12"
100–300mm
Accuracy
.00008"
0.002mm
.00012"
0.003mm
.0002"
0.005mm
Range
.275–.5"
6–12mm
.5–4"
12–100mm
4–12"
100–300mm
4–20N
15–45N
30–75N
Specifications
Holtest
Inch with Carbide
Set
Order No.
368-921
Range
Individual
Order No.
Graduation
L1
L2
.275–.350"
.350–.425"
.425–.500"
368-201
368-202
368-203
.0001"
.0001"
.0001"
2.32"
2.32"
2.32"
4.05"~4.13"
4.05"~4.13"
4.05"~4.13"
Range
Individual
Order No.
Graduation
L1
L2
6–8mm
8–10mm
10–12mm
368-101
368-102
368-103
0.001mm
0.001mm
0.001mm
59mm
59mm
59mm
103~105mm
103~105mm
103~105mm
Accessories
included in Set
177-179 Setting Ring .350" DIA.
952322 Extension Rod 4"
205289 Spanners (pair)
202863 Hex Wrench
Metric with Carbide
Set
Order No.
368-901
N-22
Accessories
included in Set
177-125 Setting Ring 8mm DIA.
177-126 Setting Ring 10mm DIA.
952322 Extension Rod 100mm
205289 Spanners (pair)
202863 Hex Wrench
12/8/03
7:21 PM
Page 1
HOLTESTS
Holtests
Series 368 – Interchangeable Anvil Type
368-206
368-238
Internal Construction
Holtest
Standard Finish
a=.012"
0.3mm
Range .5-1.2"
12-30mm
16
Holtest
with Carbide
24
1
Specifications
Inch
Set
Order No.
368-982
368-922
368-968
Range
Individual
Order No.
Graduation
L1
L2
Accessories included in Set
Hardened Alloy Tool Steel Anvil and Cone (Standard Finish)
.500–.650"
368-804
.0002"
3.15"
4.88~5.04"
.650–.800"
368-805
.0002"
3.15"
4.88~5.04"
177-182 Setting Ring, .650" DIA.
With Carbide
.500–.650"
.650–.800"
205312 Spanners (Pair)
368-204
368-205
.0002"
.0002"
3.15"
3.15"
.800–1.000"
368-806
.0002"
3.54"
1.000–1.200"
368-807
.0002"
3.54"
1.200–1.600"
368-838
.0002"
3.86"
1.600–2.000"
368-839
.0002"
3.86"
4.88~5.04"
4.88~5.04"
5.31~5.51"
5.31~5.51"
5.67~6.06"
5.67~6.06"
952621 Extension Rod, 5.9"
202863 Hex Wrench
177-184 Setting Ring, 1.000" DIA.
368-958
With Carbide
.800–1.000"
1.000–1.200"
1.200–1.600"
1.600–2.000"
368-206
368-207
368-238
368-239
.0002"
.0002"
.0002"
.0002"
3.54"
3.54"
3.86"
3.86"
5.31~5.51"
5.31~5.51"
5.67~6.06"
5.67~6.06"
210189 Spanner (Pair)
202863 Hex Wrench
N-23
12/8/03
7:23 PM
Page 1
HOLTESTS
Holtests
Series 368
a= .012"
0.3mm
Range .5-4"
12-100mm
a= .134"
3.4mm
Range .5-4"
12-100mm
a= .512"
13mm
Range 4-12"
100-300mm
a= .772"
19.6mm
Range 4-12"
100-300mm
Specifications
Inch
Set
Order No.
Individual
Range
Order No.
Graduation
L1
Hardened Alloy Tool Anvil and Cone (Standard Finish)
2.0–2.5"
368-840
.0002"
4.13"
368-969
2.5–3.0"
368-841
.0002"
4.13"
3.0–3.5"
368-842
.0002"
4.13"
3.5–4.0"
368-843
.0002"
4.13"
With Carbide
2.0–2.5"
368-240
.0002"
4.13"
368-959
2.5–3.0"
368-241
.0002"
4.13"
3.0–3.5"
368-242
.0002"
4.13"
3.5–4.0"
368-243
.0002"
4.13"
4–5"
368-817
.0002"
6.22"
368-985
5–6"
368-818
.0002"
6.22"
6–7"
368-819
.0002"
6.22"
7–8"
368-820
.0002"
6.22"
With Carbide
4–5"
368-217
.0002"
6.22"
368-925
5–6"
368-218
.0002"
6.22"
6–7"
368-219
.0002"
6.22"
7–8"
368-220
.0002"
6.22"
8–9"
368-821
.0002"
6.22"
9–10"
368-822
.0002"
6.22"
10–11"
368-823
.0002"
6.22"
11–12"
368-824
.0002"
6.22"
With Carbide
8–9"
368-221
.0002"
6.22"
9–10"
368-222
.0002"
6.22"
10–11"
368-223
.0002"
6.22"
11–12"
368-224
.0002"
6.22"
NOTE: “Holtest” Sets are not available over 8" Range.
N-24
L2
5.94~6.46"
5.94~6.46"
5.94~6.46"
5.94~6.46"
5.94~6.46"
5.94~6.46"
5.94~6.46"
5.94~6.46"
8.78~9.76"
8.78~9.76"
8.78~9.76"
8.78~9.76"
8.78~9.76"
8.78~9.76"
8.78~9.76"
8.78~9.76"
8.78~9.76"
8.78~9.76"
8.78~9.76"
8.78~9.76"
8.78~9.76"
8.78~9.76"
8.78~9.76"
8.78~9.76"
Accessories
included in Set
202863 Hex. Wrench
177-299 Setting Ring, 5" Dia.
177-303 Setting Ring, 7" Dia.
202863 Hex. Wrench
Larger Holtests are sold
individually. No set available.
12/8/03
7:25 PM
Page 1
HOLTESTS
Holtests
Series 368
Specifications
Metric
Set
Order No.
368-972
368-902
368-963
368-953
368-964
368-954
368-975
368-905
Individual
Range
Order No.
Hardened Alloy Tool Steel Anvil
12–16mm
368-704
16–20mm
368-705
With Carbide
12–16mm
368-104
16–20mm
368-105
20–25mm
368-706
25–30mm
368-707
30–40mm
368-738
40–50mm
368-739
With Carbide
20–25mm
368-106
25–30mm
368-107
30–40mm
368-138
40–50mm
368-139
50–63mm
368-740
62–75mm
368-741
75–88mm
368-742
87–100mm
368-743
With Carbide
50–63mm
368-140
62–75mm
368-141
75–88mm
368-142
87–100mm
368-143
100–125mm
368-717
125–150mm
368-718
150–175mm
368-719
175–200mm
368-720
With Carbide
100–125mm
368-117
125–150mm
368-118
150–175mm
368-119
175–200mm
368-120
200–225mm
368-721
225–250mm
368-722
250–275mm
368-723
275–300mm
368-724
With Carbide
200–225mm
368-121
225–250mm
368-122
250–275mm
368-123
275–300mm
368-124
Graduation
L1
L2
and Cone (Standard Finish)
0.005mm
80mm
124~128mm
0.005mm
80mm
124~128mm
0.005mm
80mm
0.005mm
80mm
0.005mm
90mm
0.005mm
90mm
0.005mm
98mm
0.005mm
98mm
124~128mm
124~128mm
0.005mm
90mm
0.005mm
90mm
0.005mm
98mm
0.005mm
98mm
0.005mm
105mm
0.005mm
105mm
0.005mm
105mm
0.005mm
105mm
135~140mm
135~140mm
144~154mm
144~154mm
0.005mm
105mm
0.005mm
105mm
0.005mm
105mm
0.005mm
105mm
0.005mm
158mm
0.005mm
158mm
0.005mm
158mm
0.005mm
158mm
151~164mm
151~164mm
151~164mm
151~164mm
0.005mm
158mm
0.005mm
158mm
0.005mm
158mm
0.005mm
158mm
0.005mm
158mm
0.005mm
158mm
0.005mm
158mm
0.005mm
158mm
223~248mm
223~248mm
223~248mm
223~248mm
0.005mm
0.005mm
0.005mm
0.005mm
158mm
158mm
158mm
158mm
135~140mm
135~140mm
144~154mm
144~154mm
151~164mm
151~164mm
151~164mm
151~164mm
223~248mm
223~248mm
223~248mm
223~248mm
223~248mm
223~248mm
223~248mm
223~248mm
Accessories included in Set
177-177 Setting Ring, 16mm DIA.
952621 Extension Rod, 150mm
202863 Hex. Wrench
177-139 Setting Ring,
25mm DIA.
202863 Hex. Wrench
202863 Hex. Wrench
177-298 Setting Ring, 125mm Dia.
177-302 Setting Ring, 175mm Dia.
202863 Hex. Wrench
Larger Holtests are sold individually.
No set available.
223~248mm
223~248mm
223~248mm
223~248mm
NOTE: “Holtest” Sets are not available over 200mm Range.
N-25
12/8/03
7:27 PM
Page 1
HOLTESTS
Digimatic Holtests
Series 468
468-234
Range
.275–.5"/6–12mm
.5"–4"/12-100mm
4–12"/100–300mm
A
.079"/2mm
.012"/0.3mm
.512"/13mm
Stand and mounting plate
are optional
982693
Optional mounting plate
Dimensions
Code No.
468-956
468-957
468-958
468-959
468-960
L1
1.77"
2.99"
4.02"
4.13"
5.94"
L2
6.81"-6.89"
7.87"-8.03"
8.78"-9.17"
8.94"-9.45"
11.5"-12.48"
ACCURACY
Range
.275–.8"
6–20mm
.8–4"
20–100mm
4–12"
100–300mm
Error
.00008"
0.002mm
.00012"
0.003mm
.0002"
0.005mm
MEASURING FORCE (per Anvil)
Range
.275–.5"
4–20N
6–20mm
.5–4"
15–45N
12–100mm
4–12"
30–75N
100–300mm
❇ Quantizing error ± 1 count.
The Digimatic Holtest is a three-point internal micrometer
with digital display (LCD).
Functions include:
Zero-setting, Preset, Data Hold, Inch/mm conversion,
Error alarm, Data output.
Features
• Efficient measurement using two measurement
modes—ABS (absolute) and INC (incremental) modes.
.0001"/0.001mm and can be linked to the M-SPC
(Mitutoyo Statistical Process Control) system.
• Battery: SR44 x 1 (541980)
N-26
• Measurement can be taken nearly up to the bottom of
the bore.
• The display automatically turns off idle after 20 minutes.
• Can measure deep holes by attaching an extension rod
(optional).
• Carbide tipped contact points.
12/8/03
7:29 PM
Page 1
HOLTESTS
Specifications
Digimatic Holtests Interchangeable-Head Sets
Inch/Metric
Range .275–.5"/6.985–12.7mm
Set Order No. 468-956
Includes:
982332
Display & Thimble Unit
952909
Interchangeable Head
.275–.35"/6.985–8.89mm
952910
.35–.425"/8.89–10.795mm
952911
.425–.5"/10.795–12.7mm
177-179
Setting Ring .350" DIA.
177-283
952322
Extension Rod 3.94" (100mm)
210187
Spanners (one pair)
202863
Hex Wrench
541980
SR44 Battery
Range .5–.8"/12.7–20.32mm
Includes:
982333
952670
.5–.65"/12.7–16.51mm
952671
.65–.8"/16.51–20.32mm
177-182
952621
210188
Spanners (one pair)
202863
Hex Wrench
541980
SR44 Battery
Range 2–4"/50.8–101.6mm
Includes:
982335
982178
2–2.5"/50.8–63.5mm
982179
2.5–3.0"/63.5–76.2mm
982180
3.0–3.5"/76.2–88.9mm
982181
3.5–4.0"/88.9–101.6mm
177-315
Setting Ring 2.5" DIA.
177-319
952623
210189
Spanners (one pair)
202863
Hex Wrench
541980
SR44 Battery
Thimble Graduation
.0002"
LCD Readout
Up to 4"
Over 4"
.00005"/0.001mm
.0001"/0.001mm
Range .8–2"/20.32–50.8mm
Includes:
982334
952672
.8–1"/20.32–25.4mm
952673
1–1.2"/25.4–30.48mm
982149
1.2–1.6"/30.48–40.64mm
982150
1.6–2.0"/40.64–50.8mm
177-184
177-291
952622
210189
Spanners (one pair)
202863
Hex Wrench
541980
SR44 Battery
Range 4–8"/101.6–203.2mm
Includes:
982336
953263
4–5"/101.6–127mm
953264
5–6"/127–152.4mm
953265
6–7"/152.4–177.8mm
953266
7–8"/177.8–203.2mm
177-299
Setting Ring 5" DIA.
177-303
Setting Ring 7" DIA.
952623
210189
Spanners (one pair)
202863
Hex Wrench
541980
SR44 Battery
For SPC output order connecting cable 937387 (40"/1m) or 965013 (80"/2m).
N-27
12/8/03
7:31 PM
Page 1
HOLTESTS
Digimatic Holtest
Series 468
468-966
Complete Unit
Sets
The Digimatic Holtest is a three-point internal micrometer
with digital display (LCD).
Functions include:
Zero-setting, Preset, Data Hold, Inch/mm conversion,
Error alarm, Data output.
Features
.00005"/0.001mm (.0001"/0.001mm for models over 4")
and can be linked to the M-SPC (Mitutoyo Statistical
Process Control) system.
Specifications
• Measurement can be taken nearly up to the bottom
of the bore.
• Most of these Holtests come in sets and all can be purchased individually.
• Power: Silver Oxide Cell (SR-44), offers 4,500 hours
of life.
• The display automatically turns off idle after 20 minutes.
To restore the display turn the thimble or press the
zero/ABS key.
Digimatic Holtest
Complete Unit Sets
Inch/Metric
Individual
Order No.
Graduation
Thimble
LCD Readout
.275-.35"/
6.925-8.89mm
468-231
.0002"
.00005"/0.001mm
.35-.425"/
8.89-10.795mm
468-232
.0002"
.00005"/0.001mm
.425-.5"/
10.795-12.7mm
468-233
.0002"
.00005"/0.001mm
Range
.5-.65"/
12.7-16.51mm
468-234
.0002"
.00005"/0.001mm
.65-.8"/
16.51-20.32mm
468-235
.0002"
.00005"/0.001mm
.8-1"/
20.32-25.4mm
468-236
.0002"
.00005"/0.001mm
For SPC output order Connecting Cable 937387 (40"/1m) or 965013 (80"/2m).
N-28
Digimatic Holtest SETS
INCLUDES:
468-231 Complete gage
210187
Spanners
202863
Hex Wrench
541980
SR44 Batteries
INCLUDES:
210180
Spanners
210188
Spanners
202863
Hex Wrench
541980
SR44 Batteries
12/8/03
7:32 PM
Page 1
HOLTESTS
Specifications
Digimatic Holtests Complete Unit Sets
Inch/Metric
Individual
Order No.
Graduation
Thimble
LCD Readout
1–1.2"/
25.4–30.48mm
468-237
.0002"
.00005"/0.001mm
1.2–1.6"/
30.48–40.64mm
468-238
.0002"
.00005"/0.001mm
1.6–2"/
40.64–50.8mm
468-239
.0002"
.00005"/0.001mm
2–2.5"/
50.8–63.5mm
468-240
.0002"
.00005"/0.001mm
2.5–3.0"/
63.5–76.2mm
468-241
.0002"
.00005"/0.001mm
3.0–3.5"/
76.2–88.9mm
468-242
.0002"
.00005"/0.001mm
3.5–4.0"/
88.9–101.6mm
468-243
.0002"
.00005"/0.001mm
4–5"/
101.6–127mm
468-244
.0002"
.0001"/0.001mm
5–6"/
127–152.4mm
468-245
.0002"
.0001"/0.001mm
6–7"/
152.4–177.8mm
468-246
.0002"
.0001"/0.001mm
7–8"/
177.8–203.2mm
468-247
.0002"
.0001"/0.001mm
8–9"/
203.2–228.6mm
468-248
.0002"
.0001"/0.001mm
9–10"/
228.6–254mm
468-249
.0002"
.0001"/0.001mm
10–11"/
254–279.4mm
468-250
.0002"
.0001"/0.001mm
11–12"/
279.4–304.8mm
468-251
.0002"
.0001"/0.001mm
Range
Digimatic Holtests Sets
(Complete Unit)
Includes:
468-237
Complete Gage
468-238
Complete Gage
468-239
Complete Gage
177-289
177-291
210189
Spanners
202863
Hex Wrench
541980
SR44 Batteries
Includes:
468-240
Complete Gage
468-241
Complete Gage
177-315
210189
Spanners
202863
Hex Wrench
541980
SR44 Batteries
Includes:
468-242
Complete Gage
468-243
Complete Gage
177-319
210189
Spanners
202863
Hex Wrench
541980
SR44 Batteries
For SPC output order connecting cable 937387 (40"/1m) or 965013 (80"/2mm)
Dimensions
Code No.
468-231, 232, 233
468-234, 235
468-236, 237
468-238, 239
468-240, 241, 242, 243
468-244, 245, 246, 247, 248
249, 250, 251
L1
1.77"
2.99"
3.46"
4.02"
4.13"
L2
6.81"-6.89"
7.87"-8.03"
8.39"-8.58"
8.78"-9.17"
8.94"-9.45"
5.94"
11.5"-12.48"
N-29
12/8/03
7:16 PM
Page 1
BORE GAGES
Dial Bore Gages
Series 545 – Rugged, Production-Line Tools
901530
(A) 4.5"
Depth (A)
From Bottom Surface to Indicators Bezel.
901529
(A) 3.5"
901531
(A)10.5"
Optional
Extensions
901533
(A)15.5"
Features
• Carbide-tipped contact point for excellent durability.
• Easy zero adjustment because the Bore Gage can
stand upright.
• Interchangeable anvils have a large radius of curvature
for repeatable ID measurements of roughly finished
holes.
• Two guide pins ensure high repeatability of measurements.
• Wide range of measurements with interchangeable
anvils (screw-in type).
• .0005"(0.01mm) or .0001"(0.001mm) reading types.
• Carbide tipped anvil (optional): 901484
901532
(A)12.5"
Replacement Heads
2.64"
1.65"
No. 901955
Range: 3-6"
75-150mm
Accuracy
No. 901956
Range: 2-3"
50-75mm
1.10"
No. 901957
Range: 1.5-2"
35-50mm
• .0002"/5mm
Specifications
Dial Bore Gages
Inch
Order No. (with Indicator)
.0005"
.0001"
545-124
545-134
545-125
545-135
545-126
545-136
Range
1.5–2"
2–3"
3–6"
Probe
Depth
3.5"
4.5"
6"
Number of
Anvil
5
5
7
Range
35–50mm
50–75mm
75–150mm
Probe
Depth
88mm
113mm
153mm
Number of
Anvil
5
5
7
Metric
Order No. (with Indicator)
0.01mm
0.001mm
545-104
545-114
545-105
545-115
545-106
545-116
N-30
12/8/03
7:17 PM
Page 1
BOREMATIC
Borematic with Absolute Encoder
Series 568
Range
Range
.275–.5"
.5–5"
4–10N
10–30N
Accuracy
Range
.275–.8"
Range
.8–5"
❇ Quantizing error ± 1 count.
568-978
.0002"
.00025"
T
EC
OG
Y
AB
LUT
SO E
H N OL
Features
• LCD Readout .00005"/0.001mm.
• Carbide tipped contact points ensure long life.
• Can be linked to the M-SPC (Mitutoyo Statistical
Process Control) system.
• Rotatable display unit for easy reading at any angle.
• Functions include:
Origin setting, Origin restoration, Zero-setting,
Presetting, Data hold, Error alarm, Low-battery alarm,
Data output.
• Power supply: SR44 (button-type silver oxide cell), 1 pc.
Specifications
Borematic Interchangeable-Head Sets
Inch/Metric
Set
Order No.
568-976
Set
Measuring Range
.275"–.5"
6.985–12.7mm
Display
Unit
568-013
Adaptor
Supplied
954595
568-977
.5"–1.0"
12.7–25.4mm
568-013
216556
568-978
1.0"–2.0"
25.4–50.8mm
568-013
216557
216557
568-979
2.0"–4.0"
50.8–101.6mm
568-013
216558
568-980
2.0"–4.0"
50.8–101.6mm
568-013
216558
Interchangeable
Contact Heads
952909
952910
952911
952670
952671
952672
952673
982149
982150
982178
982179
982180
982181
04AZA047*
04AZA048*
Individual
Range
.275"–.35"/6.985–8.89mm
.35"–.425"/8.89–10.795mm
.425"–.5"/10.795–12.7mm
.5"–.65"/12.7–16.51mm
.65"–.8"/16. 51–20.32mm
.8"–1.0"/20.32–25.4mm
1.0"–1.2"/25.4–30.48mm
1.2"–1.6"/30.48–40.64mm
1.6"–2.0"/40.64–50.8mm
2.0"–2.5"/50.8–63.5mm
2.5"–3.0"/63.5–76.2mm
3.0"–3.5"/76.2–88.9mm
3.5"–4.0"/88.9–101.6mm
2.0"–2.5"/50.8–63.5mm
2.5"–3.0"/63.5–76.2mm
3.0"–3.5"/76.2–88.9mm
3.5"–4.0"/88.9–101.6mm
Setting Ring
Supplied w/set
177-179(.35")
177-283(.425")
177-182(.65")
177-287(.8")
177-289(1.2")
177-291(1.6")
177-315(2.5")
177-319(3.5")
177-315(2.5")
177-319(3.5")
* Two sets of interchangeable contact points are provided.
For SPC output order connecting cable 937387(40"/1m) or 965013(80"/2m).
N-31
12/8/03
7:20 PM
Page 1
BOREMATIC
Borematic with Absolute Encoder
Series 568
568-988
LUT
SO E
T
EC
OG
Y
AB
c
H N OL
Unit:Inch (mm)
Dimensions
Optional Extension Rods for
Measuring Deep Bores
Order No.
952322
952621
952622
952623
Length
3.94"(100mm)
5.9"(150mm)
5.9"(150mm)
5.9"(150mm)
Remarks
for .275–.5" gages
for .5–.8" gages
for .8–2" gages
for 2"–5" gages
Specifications
Range
L
a
b
c
.275-.5"
(6-12mm)
.5-.8"
(12-20mm)
.8-1.2"
(20-30mm)
1.2-2"
(30-50mm)
2-4"
(50-125mm)
3.27"
(83mm)
2.07"
(52.6mm)
2.29"
(58.2mm)
2.65"
(67.3mm)
2.94"
(74.8mm)
2.28"
(58mm)
2.28"
(58mm)
2.28"
(58mm)
2.28"
(58mm)
2.64"
(67mm)
.10"
(2.5mm)
.25"
(6.3mm)
.35"
(8.8mm)
.55"
(14mm)
.67"
(17mm)
.078"
(2mm)
.012"
(0.3mm)
.012"
(0.3mm)
.012"
(0.3mm)
.012"
(0.3mm)
Borematic Complete-Unit Sets
Inch/Metric
Set
Order No.
568-987
Set
Measuring Range
.275"–.5"
6.985–12.7mm
568-988
.5"–1"
12.7–25.4mm
568-989
1.0"–2.0"
25.4–50.8mm
568-990
2.0"–3.0"
50.8–76.2mm
3.0"–4.0"
76.2–101.6mm
2.0"–4.0"
50.8–101.6mm
568-991
568-992
Individual
Order No.
568-431
568-432
568-433
568-434
568-435
568-436
568-437
568-438
568-439
568-440
568-441
568-442
568-443
568-446*
568-447*
––
568-448*
Individual
* Range
.275"–.35"/6.985–8.89mm
.35"–.425"/8.89–10.795mm
.425"–.5"/10.795–12.7mm
.5"–.65"/12.7–16.51mm
.65"–.8"/.16.51–20.32mm
.8"–1.0"/20.32–25.4mm
1.0"–1.2"/25.4–30.48mm
1.2"–1.6"/30.48–40.64mm
1.6"–2.0"/40.64–50.8mm
2.0"–2.5"/50.8–63.5mm
2.5"–3.0"/63.5–76.2mm
3.0"–3.5"/76.2–88.9mm
3.5"–4.0"/88.9–101.6mm
2.0"–2.5"/50.8–63.5mm
2.5"–3.0"/63.5–76.2mm
3.0"–3.5"/76.2–88.9mm
3.5"–4.0"/88.9–101.6mm
4.0"–4.5"/101.6–114.3mm
4.5"–5.0"/114.3–127mm
* Two sets of interchangeable contact points are provided.
For SPC output order connecting cable 937387(40"/1m) or 965013(80"/2m).
N-32
Setting Ring
Supplied w/set
177-179(.35")
177-283(.425")
177-182(.65")
177-287(.8")
177-289(1.2")
177-291(1.6")
177-315(2.5")
177-319(3.5")
177-315(2.5")
177-319(3.5")
12/8/03
7:21 PM
Page 1
SETTING RINGS
Setting Rings
Series 177
Specifications
Inch
Size
.1"
Metric
Order
No.
177-209
Accuracy
Outside
Diameter
Width
.98"
.28"
Size
1.75mm
Order
No.
177-236
.16"
177-206
2.0mm
177-239
.24"
177-207
2.25mm
177-242
.275"
177-281
2.5mm
177-208
177-179
2.75mm
177-246
177-283
3.0mm
177-248
177-180
3.25mm
177-250
177-181
3.5mm
177-252
3.75mm
177-255
4.0mm
177-204
4.5mm
177-257
5.0mm
177-205
5.5mm
177-263
.35"
.425"
.50"
.6"
.65"
177-182
.70"
177-183
.8"
177-287
1.0"
177-184
1.26"
1.5"
.39"
1.77"
2.09"
1.2"
177-289
1.4"
177-185
6.0mm
177-267
1.6"
177-291
6.5mm
177-271
1.8"
177-186
7.0mm
177-275
2.0"
177-187
8.0mm
177-125
2.4"
177-293
10.0mm
177-126
2.5"
177-315
12.0mm
177-284
2.8"
177-188
14.0mm
177-132
3.0"
177-317
16.0mm
177-177
3.2"
177-295
17.0mm
177-133
3.5"
177-319
20.0mm
177-286
3.6"
177-189
25.0mm
177-139
4.0"
177-297
6.3"
30.0mm
177-288
5.0"
177-299
8.27"
35.0mm
177-140
6.0"
177-301
9.25"
40.0mm
177-290
7.0"
177-303
10.24"
45.0mm
177-178
12.24"
50.0mm
177-146
13.27"
60.0mm
177-292
177-314
8.0"
177-305
9.0"
177-307
±.00006"
2.8"
.59"
3.35"
.79"
4.41"
4.92"
5.51"
±.00010"
.98"
1.5"
Accuracy
Outside
Diameter
5mm
25mm
7mm
32mm
±0.0015mm
38mm
53mm
71mm
177-309
14.25"
11.0"
177-311
16.26"
70.0mm
177-147
17.24"
75.0mm
177-316
80.0mm
177-294
87.0mm
177-318
90.0mm
177-148
100.0mm
177-296
160mm
125.0mm
177-298
210mm
150.0mm
177-300
235mm
175.0mm
177-302
200.0mm
177-304
Metric
140mm
1.1mm
177-222
1.2mm
177-225
1.3mm
177-227
225.0mm
177-306
337mm
1.4mm
177-230
250.0mm
177-308
362mm
275.0mm
177-310
413mm
300.0mm
177-312
438mm
20mm
Width
4mm
20mm
125mm
Order
No.
177-220
±0.0015mm
Outside
Diameter
112mm
Size
1.0mm
Accuracy
15mm
85mm
10.0"
177-313
10mm
45mm
62.0mm
12.0"
Width
25mm
260mm
±0.0025mm
311mm
38.1mm
N-33
12/8/03
7:24 PM
Page 1
AIR GAGING PRODUCTS
MSG/MLS Air Gaging Models
MSG Models
MLS Models
Specifications
Measuring Channels
Air
LVDT
Digital
Measuring Programs
Resolution
Communication Ports
RS232C
RJ485
USB
Opto I/O
Ethernet
Program switch Connector
Printer Port
MSG Models
MLS Models
1 standard, (optional to 4 maximum)
optional to 8 maximum
optional 4, 8, 16
4 standard, optional 9 or 18
.1µm minimum
1 standard
2 standard
N/A
4 standard
.1 µm minimum
1 standard (optional to 2 maximum)
optional (2x)
optional
standard
standard
standard
optional
1 standard
2 standard
N/A
standard
N/A
standard
optional
The MSG model column is fully configurable to any air electronic application. Unit can act as master or slave in control feed
back environment. Display graphics are also configurable to your specific requirements. Please contact Mitutoyo America
Corporation representatives for further information.
The MLS model is offered as a limited measurement purpose device using a single air and two LVDT channels. LVDT's are 5
pin, half bridge style.
Mitutoyo also offers a complete line of air gage tooling to support our columns as well as the capability to supply tooling and
masters in many configurations for most competitive brands. In addition we can ship all gages with a long form certification
from our calibration labs.
N-34
12/8/03
7:26 PM
Page 1
CHAMFER-CHEK
Chamfer Chek
Series 526 –
I.D. Measures the top diameter of tapered holes and chamfers
O.D. measures the minor end diameter of tapered conical parts
I.D.
526-005C
O.D.
526-008C
526-005C shown with optional setting master.
Features
• Ease of operation: Simply insert the steel plunger into the
hole, press firmly against the part and read the diameter
directly to three decimal places.
• Resolution: Reads directly to .001" for 0°–90° models.
• Applications: Steel valve inserts, brass fittings, machine
tools and holders, steel check valves, circuit boards,
sheet metal and stampings, pressure vessels, bronze
bushings, steel governor cups.
Black Leather Case: (21BZA778) 9.7"(W) x 2"(D) x 6.1"(H)
*Wooden Box: (21BZA779) 12.8"(W) x 5.1"(D) x 3.63"(H)
*526-006C (CI-2090) only
Master Plate: (64AAA012) 3"(W) x 2"(D) x .925"(H)
Setting Master
Order No.
Model No.
Chamfer Chek I.D.
64AAA007
SM-1000
64AAA008
SM-2000
64AAA133
64AAA134
Chamfer Chek O.D.
64AAA009
SM-1000E
*Denotes a double-sided setting master.
Diameter
Specifications
Range:
Accuracy:
Graduation:
Gage Weight:
0–90°
.001"
.001" Dia.
526-005C
526-006C
526-007C
526-008C
Order No.
Chamfer Chek I.D.
526-005C
526-006C
526-005M
Chamfer Chek O.D.
526-007C
526-008C
1 lbs. (454g)
1.21 lbs. (545g)
1 lbs. (454g)
1 lbs. (454g)
Model No.
Diameter Range
CI-1090
CI-2090**
CI-1090M
.02–1"
1–2"
0.5–25mm
CO-0590
CO-1090
1/8–1/2"
3/8–1"
*.375"/.750" (I.D.)
*1.25"/1.75" (I.D.)
9.525mm (I.D.)
19.05mm (I.D.)
*.375"/.750" (O.D.)
N-35
12/8/03
7:28 PM
Page 1
CHAMFER-CHEK
Digimatic Chamfer Chek
Series 547 –
I.D. Measures the top diameter of tapered holes and chamfers
O.D. measures the minor end diameter of tapered conical parts
I.D.
547-480
O.D.
547-482
547-480 Shown with optional setting master.
Master Plate (64AAA012), 3"(W) x 2"(D) x .925"(H)
Black Leather Case (21BZA778) 9.7"(W) x 2"(D) x 6.1"(H)
*Wooden box (21BZA779) 12.8"(W) x 5.1"(D) x 3.63"(H)
* 547-481 (DC1-2090) only
Digimatic Chamfer Chek
Order No.
Model No.
Diameter Range
Resolution
Chamfer Chek I.D.
547-480
DCI-1090
.02-1"/0.5-25.4mm
.0005"/0.01mm
547-481
DCI-2090
1-2"/25.4-50.8mm
.0005"/0.01mm
Chamfer Chek O.D.
547-482
DCO-0590
1/8"-1/2"/3.18-12.7mm
.0005"/0.01mm
547-483
DCO-1090
3/8"-1"/9.52-25.4mm
.0005"/0.01mm
For SPC output order Connecting Cable 905338 (40"/1m) or 905409 (80"/2m).
N-36
Accuracy
Mass
±.001"/0.025mm
±.001"/0.025mm
1.75lbs./793g
3.97lbs./1,800g
±.001"/0.025mm
±.001"/0.025mm
1.75lbs./793g
1.75lbs./793g
12/8/03
7:29 PM
Page 1
HOLE-CHEK
Hole Chek
Series 526 – Instant Diameter Measurement of Small Holes
526-003H
526-001H
526-002H shown with optional setting master.
Features
Specifications
• Ease of Operation: Simply insert the steel plunger into
the hole and press firmly against the part and read the
diameter directly to three decimal places.
• Resolution: Reads directly in .001" diameter increments.
• Applications: Inspect PC boards, screw machine parts,
spray tips, injector nozzles, plastic molded parts.
Accuracy:
.001"
Graduation:
.001" Dia.
Gage Weight: 526-001H 1
526-002H 1
526-003H 1
526-004H 1
Wooden Box: 12.8"(W) x 5.1"(D) x 3.2"(H)
Granite Plate: 3"(W) x 2"(D) x .925"(H) (64AAAO12)
Order No.
526-001H
526-002H
526-003H
526-004H
lbs. (454g)
lbs. (454g)
lbs. (454g)
lbs. (454g)
Model No.
HC-0040
HC-0130
HC-0230
HC-0330
Dia. Range
.010"–.040"
.030"–.130"
.130"–.230"
.230"–.330"
Setting Master (O.D. = .76"/H = .29")
Order No.
64AAA003
64AAA004
64AAA005
64AAA006
Model No.
SM-040
SM-130
SM-230
SM-330
Diameter
.029"
.078"
.178"
.278"
N-37

MITUTOYO - INSIDE MEASURING

Transcription

Similar documents

Holtest Digimatic Holtest C-2, 3 Holtest C-4, 5 Holtest (Type II) C

Bore Gages

Bore Gages

runterholen