Holtest Digimatic Holtest C-2, 3 Holtest C-4, 5 Holtest (Type II) C
Transcription
INDEX Holtest Digimatic Holtest C-2, 3 Holtest C-4, 5 Holtest (Type II) C-6, 7 Borematic C-8, 9 Inside Micrometer Tubular Inside Micrometers C-10, 11 Inside Micrometers C-12 Digimatic Tubular Inside Micrometers C-13 Tubular Inside Micrometers C-14 Tubular Inside Micrometers C-15 Tubular Inside Micrometers C-16 Inside Micrometers C-17 Inside Micro Checker C-18 Bore Gages Bore Gages C-19 – 25 ABSOLUTE Digimatic Bore Gage C-26 Bore Gages C-27 Dial Bore Gages C-28 Digimatic Chamfer Chek C-29 Digimatic Hole Chek C-29 Setting Ring C-30 Ceramic Setting Ring C-31 Bore Gage Zero Checker C-31 RM-120 Ring Master C-32 Holtest ABSOLUTE Borematic Inside Micrometer Small Tool Instruments and Data Management INDEX Holtest Digimatic Holtest Holtest Holtest (Type II) Borematic Inside Micrometer Tubular Inside Micrometers Inside Micrometers Digimatic Tubular Inside Micrometers Tubular Inside Micrometers Tubular Inside Micrometers Tubular Inside Micrometers Inside Micrometers Inside Micro Checker Bore Gages Bore Gages ABSOLUTE Digimatic Bore Gage Bore Gages Dial Bore Gages Digimatic Chamfer Chek Digimatic Hole Chek Setting Ring Ceramic Setting Ring Bore Gage Zero Checker RM-120 Ring Master Bore Gages New Products Digimatic Holtest Holtest Absolute Borematic Digimatic Inside Micrometer Digimatic Bore Gage C-1 C-2, 3 C-4, 5 C-6, 7 C-8, 9 C-10, 11 C-12 C-13 C-14 C-15 C-16 C-17 C-18 C-19 – 25 C-26 C-27 C-28 C-29 C-29 C-30 C-31 C-31 C-32 Digimatic Holtest SERIES 468 — Three-Point Internal Micrometers FEATURES •TiN-coated measuring contact points (over 12mm range models) provide excellent durability and impact resistance and allow the instrument to measure to the bottom of a blind hole ( up to 100mm / 4”models). •Large LCD readout. •Functions available: Presetting, Zero/ABS, Auto power On/Off, Data hold, Data output, Error alarm, Battery replacement alarm. •With Ratchet Stop for constant force. •Can measure deep holes by attaching an Extension rod (optional). •Setting rings for origin point setting are optional. •Supplied in fitted plastic case up to 100mm / 4”. Over 100mm / 4” supplied in wooden case. Technical Data Accuracy: Refer to the list of specifications. (Excluding Quantizing Error) Resolution: 0.001mm or .00005"/0.001mm (over 4 - 5" models: .0001"/0.001mm) Contact point: Carbide or TiN coating* (*over 12mm/.5" models) Measuring method: Three-point method Display: LCD Battery: SR44 (2 pcs.), 938882 Battery life: Approx. 8 months under normal use Function Zero/ABS, Auto Power On/Off, Data hold, Data output, Preset, inch/mm conversion (on inch/metric models only) Alarm: Low voltage, Counting value composition error Optional Accessories 468-131 468-238-10 937387: 965013: 982693: 156-101: SPC cable (1m / 40”) SPC cable (2m / 80”) Mounting plate for stand Stand 952322: Extension rod 100mm / 3.94” For range 6-12mm / .275 - .5” models 952621: Extension rod 150mm / 5.9” For range 12-20mm / .5" - .8” models 952622: Extension rod 150mm / 5.9” For range 20-50mm / .8" - 2” models 952623: Extension rod 150mm / 5.9” For range 50-300mm / 2" - 12” models TiN coated contact points ("-10" suffix models only) DIMENSIONS AND MASS 468-144-10 L 45 45 45 76 76 91 103 103 102 105 105 105 105 151 151 151 151 151 151 151 151 Mass (g) 400 400 400 430 430 500 510 510 530 650 660 990 1000 970 1060 1150 1240 1330 1420 1510 1600 C-2 Measuring a Blind Hole The measuring contact points held in the jaws permit measuring the diameter of a blind hole to the bottom. ( up to 100mm / 4”models) L V Range 6 - 8mm / .275 - .35” 8 - 10mm / .35 - .425” 10 - 12mm / .425 - .5” 12 - 16mm / .5 - .65” 16 - 20mm / .65 - .8” 20 - 25mm / .8 - 1" 25 - 30mm / 1 - 1.2" 30 - 40mm / 1.2 - 1.6" 40 - 50mm / 1.6 - 2" 50 - 63mm / 2 - 2.5" 62 - 75mm / 2.5 - 3.0" 75 - 88mm / 3.0 - 3.5" 87 - 100mm / 3.5 - 4.0" 100 - 125mm / 4 - 5" 125 - 150mm / 5 - 6" 150 - 175mm / 6 - 7" 175 - 200mm / 7 - 8" 200 - 225mm / 8 - 9" 225 - 250mm / 9 - 10" 250 - 275mm / 10 - 11" 275 - 300mm / 11 - 12" > Unit: mm Range 6 - 12mm / .275 - .5” 12 - 20mm / .5 - .8” 20 - 30mm / .8 - 1.2” 30 - 50mm / 1.2 - 2" 50 - 100mm / 2 - 4" 100 - 300mm / 4 - 12" a 2 0.3 0.3 0.3 0.3 12.4 b — 5.6 8.3 13 17 21 c 2.5 3.5 5.2 10 14 13.8 982693 SPECIFICATIONS Metric Inch/Metric Individual Order No. 468-131 468-132 468-133 468-134-10 468-135-10 468-136-10 468-137-10 468-138-10 468-139-10 468-140-10 468-141-10 468-142-10 468-143-10 468-144-10 468-145-10 468-146-10 468-147-10 468-148-10 468-149-10 468-150-10 468-151-10 Range 6 - 8mm 8 - 10mm 10 - 12mm 12 - 16mm 16 - 20mm 20 - 25mm 25 - 30mm 30 - 40mm 40 - 50mm 50 - 63mm 62 - 75mm 75 - 88mm 87 - 100mm 100 - 125mm 125 - 150mm 150 - 175mm 175 - 200mm 200 - 225mm 225 - 250mm 250 - 275mm 275 - 300mm Accuracy ±2µm ±2µm ±2µm ±2µm ±2µm ±3µm ±3µm ±3µm ±3µm ±3µm ±3µm ±3µm ±3µm ±5µm ±5µm ±5µm ±5µm ±5µm ±5µm ±5µm ±5µm Carbide with TiN coated contact points Individual Range .275 - .35" / 6.925 - 8.89mm .35 - .425" / 8.89 - 10.795mm .425 - .5" / 10.795 - 12.7mm .5 - .65" / 12.7 - 16.51mm .65 - .8" / 16.51 - 20.32mm .8 - 1" / 20.32 - 25.4mm 1 - 1.2" / 25.4 - 30.48mm 1.2 - 1.6" / 30.48 - 40.64mm 1.6 - 2" / 40.64 - 50.8mm 2 - 2.5" / 50.8 - 63.5mm 2.5 - 3" / 63.5 - 76.2mm 3 - 3.5" / 76.2 - 88.9mm 3.5 - 4" / 88.9 - 101.6mm 4 - 5" / 101.6 - 127mm 5 - 6" / 127 - 152.4mm 6 - 7" / 152.4 - 177.8mm 7 - 8" / 177.8 - 203.2mm 8 - 9" / 203.2 - 228.6mm 9 - 10" / 228.6 - 254mm 10 - 11" / 254 - 279.4mm 11 - 12" / 279.4 - 304.8mm Order No. 468-231 468-232 468-233 468-234-10 468-235-10 468-236-10 468-237-10 468-238-10 468-239-10 468-240-10 468-241-10 468-242-10 468-243-10 468-244-10 468-245-10 468-246-10 468-247-10 468-248-10 468-249-10 468-250-10 468-251-10 Accuracy ±.0001" ±.0001" ±.0001" ±.0001" ±.0001" ±.00015" ±.00015" ±.00015" ±.00015" ±.00015" ±.00015" ±.00015" ±.00015" ±.00025" ±.00025" ±.00025" ±.00025" ±.00025" ±.00025" ±.00025" ±.00025" Complete Unit Set Each set includes complete gages (display units and measuring heads for each size). Carbide Metric Range 6 - 12mm 12 - 25mm 25 - 50mm 50 - 75mm 75 - 100mm with TiN coated contact points Order No. 468-961 468-962-10 468-963-10 468-964-10 468-965-10 Individual range 6-8, 8-10, 10-12mm 12-16, 16-20, 20-25mm 25-30, 30-40, 40-50mm 50-63, 62-75mm 75-88, 87-100mm Setting rings included ø8mm, ø10mm ø16mm, ø20mm ø30mm, ø40mm ø62mm ø87mm Carbide with TiN coated contact points Inch/Metric 468-963-10 Remarks — — — — — Order No. 468-966 468-967-10 468-968-10 468-969-10 468-970-10 Range .275 - .5" / 6.925 - 12.7mm .5 - 1" / 12.7 - 25.4mm 1 - 2" / 25.4 - 50.8mm 2 - 3" / 50.8 - 76.2mm 3 - 4" / 76.2 - 101.6mm Individual range .275-.35", .35-.425", .425-.5" .5-.65", .65-.8", .8-1" 1-1.2", 1.2-1.6", 1.6-2" 2-2.5", 2.5-3" 3-3.5", 3.5-4" Setting rings included .35" DIA., .425" DIA. .65" DIA., .8" DIA. 1.2" DIA., 1.6" DIA. 2.5" DIA. 3.5" DIA. Remarks — — — — — Interchangeable Head Set Each set includes one display unit with interchangeable measuring heads of the sizes specified. Carbide with TiN coated contact points Metric Range 6 - 12mm 12 - 20mm 20 - 50mm 50 - 100mm 100 - 200mm Order No. 468-951 468-952-10 468-953-10 468-954-10 468-955-10 Individual range 6-8, 8-10, 10-12mm 12-16, 16-20mm 20-25, 25-30, 30-40, 40-50mm 50-63, 62-75, 75-88, 87-100mm 100-125, 125-150, 150-175, 175-200mm Setting rings included ø8mm, ø10mm ø16mm. ø25mm, ø40mm ø62mm, ø87mm ø125mm, ø175mm Carbide with TiN coated contact points Inch/Metric 468-953-10 Range .275 - .5" / 6.925 - 12.7mm .5 - .8" / 12.7 - 20.32mm .8 - 2" / 20.32 - 50.8mm 2 - 4" / 50.8 - 101.6mm 4 - 8" / 101.6 - 203.2mm Remarks with extension rod with extension rod with extension rod with extension rod with extension rod Order No. 468-956 468-957-10 468-958-10 468-959-10 468-960-10 Individual range .275-.35", .35-.425", .425-.5" .5-.65", .65-.8" .8-1", 1-1.2", 1.2-1.6", 1.6-2" 2-2.5", 2.5-3", 3-3.5", 3.5-4" 4-5", 5-6", 6-7", 7-8" C-3 Setting rings included .35" DIA., .425" DIA. .65" DIA. 1" DIA., 1.6" DIA. 2.5" DIA., 3.5" DIA 5" DIA., 7" DIA. Remarks with extension rod with extension rod with extension rod with extension rod with extension rod Holtest SERIES 368 — Three-Point/Two-Point Internal Micrometers FEATURES These Holtests are versatile, self-centering three-point internal micrometers for the accurate and efficient direct-measurement of internal diameters. Three anvils, evenly spaced at 120° apart, contact the internal wall surfaces and find true alignment with the axis of the bore for accurate ID measurement. •TiN-coated measuring contact points (over 12mm range models) provide excellent durability and impact resistance and allow the instrument to measure to the bottom of a blind hole (up to 100mm / 4”models). •Highly durable because of carbide-tipped contact points (anvils up to 12mm / .5”models). •Can measure deep holes using an Extension rod (optional) which is available on models over 6mm (.275") measuring range. •With Ratchet Stop for constant force. •Setting Rings for zero point adjustment are optional. •Supplied in fitted plastic case up to 100mm / 4”. Over 100mm / 4” supplied in wooden case. 368-001 Technical Data Graduation: 0.001mm, 0.005mm*, .0001" or .0002"* (*over 12mm or .5” models) Range 2 - 3mm / .08 - .12" 3 - 6mm / .12 - .28" 6 - 12mm / .28 - .5" over 12mm / over .5" Measuring method Two-point method Two-point method Three-point method Three-point method Contact-point material Hardened steel (HRC60.5 or more) Hardened steel (HRC60.5 or more) Carbide TiN coating (1700-2000Hv) Optional Accessories 952322: Extension rod 100mm / 3.94” For range 6-12mm / .275-.5” models 952621: Extension rod 150mm / 5.9” For range 12-20mm / .5" - .8” models 952622: Extension rod 150mm / 5.9” For range 20-50mm / .8" - 2” models 952623: Extension rod 150mm / 5.9” For range 50-300mm / 2"-12” models 368-268 Two-point contact type Cone TiN coated contact points (excluding models up to 12mm/.5") 368-174 DIMENSIONS Carbide ball Carbide ball Carbide pin Cone Carbide pin Contact point Carbide tip or TiN coating Unit: mm Measuring a Blind Hole Range 2 - 2.5mm / .08 - .1” 2.5 - 3mm / .1 - .12" 3 - 4mm / .12 - .16" 4 - 5mm / .16 - .2" 5 - 6mm / .2 - .24" 6 - 8mm / .275 - .35" 8 - 10mm / .35 - .425" 10 - 12mm / .425 - .5" 12 - 16mm / .5 - .65" 16 - 20mm / .65 - .8" 20 - 25mm / .8 - 1" 25 - 30mm / 1 - 1.2" 30 - 40mm / 1.2 - 1.6" L 12 12 22 22 22 59 59 59 82 82 94 94 102 Mass (g) 88 88 91 91 91 57 58 59 140 145 250 270 290 Range 2 - 6mm / .08 - .275” 6 - 12mm / .275 - .5” 12 - 20mm / .5 - .8" 20 - 30mm / .8 - 1.2" 30 - 50mm / 1.2 - 2" 50 - 100mm / 2 - 4" 100 - 300mm / 4 - 12" > L V The measuring contact points held in the jaws permit measuring the diameter of a blind hole right down to the bottom (up to 100mm / 4”models). C-4 Range 40 - 50mm / 1.6 - 2" 50 - 63mm / 2 - 2.5" 62 - 75mm / 2.5 - 3" 75 - 88mm / 3 - 3.5" 87 - 100mm / 3.5 - 4" 100 - 125mm / 4 - 5" 125 - 150mm / 5 - 6" 150 - 175mm / 6 - 7" 175 - 200mm / 7 - 8" 200 - 225mm / 8 - 9" 225 - 250mm / 9 - 10" 250 - 275mm / 10 - 11" 275 - 300mm / 11 - 12" a — 2 0.3 0.3 0.3 0.3 12.4 b — — 5.6 8.3 13 17 21 c 2 2.5 3.5 5.2 10 14 13.8 L 102 105 105 105 105 161 161 161 161 161 161 161 161 Mass (g) 330 440 450 490 500 1050 1120 1190 1260 1420 1580 1600 1690 Using the optional extension rod Contact point SPECIFICATIONS Metric Inch Individual Order No. 368-001 368-002 368-003 368-004 368-005 368-101-10 368-102-10 368-103-10 368-164 368-165 368-166 368-167 368-168 368-169 368-170 368-171 368-172 368-173 368-174 368-175 368-176 368-177 368-178 368-179 368-180 368-181 Range 2 - 2.5mm 2.5 - 3mm 3 - 4mm 4 - 5mm 5 - 6mm 6 - 8mm 8 - 10mm 10 - 12mm 12 - 16mm 16 - 20mm 20 - 25mm 25 - 30mm 30 - 40mm 40 - 50mm 50 - 63mm 62 - 75mm 75 - 88mm 87 - 100mm 100 - 125mm 125 - 150mm 150 - 175mm 175 - 200mm 200 - 225mm 225 - 250mm 250 - 275mm 275 - 300mm Accuracy ±2µm ±2µm ±2µm ±2µm ±2µm ±2µm ±2µm ±2µm ±2µm ±2µm ±3µm ±3µm ±3µm ±3µm ±3µm ±3µm ±3µm ±3µm ±5µm ±5µm ±5µm ±5µm ±5µm ±5µm ±5µm ±5µm Range .08 - .1" .1 - .12" .12 - .16" .16 - .2" .2 - .24" .24 - .28" .275 - .35" .35 - .425" .425 - .5" .5 - .65" .65 - .8" .8 - 1" 1 - 1.2" 1.2 - 1.6" 1.6 - 2" 2 - 2.5" 2.5 - 3" 3 - 3.5" 3.5 - 4" 4 - 5" 5 - 6" 6 - 7" 7 - 8" 8 - 9" 9 - 10" 10 - 11" 11 - 12" Individual with TiN coated contact points Order No. 368-021 368-022 368-023 368-024 368-025 368-026 368-201-10 368-202-10 368-203-10 368-264 368-265 368-266 368-267 368-268 368-269 368-270 368-271 368-272 368-273 368-274 368-275 368-276 368-277 368-278 368-279 368-280 368-281 Accuracy ±.0001" ±.0001" ±.0001" ±.0001" ±.0001" ±.0001" ±.0001" ±.0001" ±.0001" ±.0001" ±.0001" ±.00015" ±.00015" ±.00015" ±.00015" ±.00015" ±.00015" ±.00015" ±.00015" ±.00025" ±.00025" ±.00025" ±.00025" ±.00025" ±.00025" ±.00025" ±.00025" Complete Unit Set Each set includes complete gages (micrometer head units and measuring heads for each size). Metric Range 2 - 3mm 3 - 6mm 6 - 12mm 12 - 20mm 20 - 50mm 50 - 100mm 100 - 200mm with TiN coated contact points Order No. 368-906 368-907 368-901-10 368-912 368-913 368-914 368-915 Individual range 2-2.5, 2.5-3mm 3-4, 4-5, 5-6mm 6-8, 8-10, 10-12mm 12-16, 16-20mm 20-25, 25-30, 30-40, 40-50mm 50-63, 62-75, 75-88, 87-100mm 100-125, 125-150, 150-175, 175-200mm Setting rings included ø2.5mm ø4mm, ø5mm ø8mm, ø10mm ø16mm ø25mm, ø40mm ø62mm, ø87mm ø125mm, ø175mm Order No. 368-926 368-927 368-921-10 368-917 368-918 368-919 368-920 Individual range .08-.1", .1-.12" .12-.16", .16-.2", .2-.24", .24-.28" .275-.35", .35-.425", .425-.5" .5-.65", .65-.8" .8-1", 1-1.2", 1.2-1.6", 1.6-2" 2-2.5", 2.5-3", 3-3.5", 3.5-4" 4-5", 5-6", 6-7", 7-8" Setting rings included .1" DIA. .16" DIA., .24" DIA. .35" DIA., .5" DIA. .65" DIA. 1" DIA., 1.6" DIA. 2.5" DIA., 3.5" DIA. 5" DIA., 7" DIA. Inch 368-906 Range .08" - .12" .12" - .28" .275" - .5" .5" - .8" .8" - 2" 2" - 4" 4" - 8" Remarks — — with extension rod with extension rod with extension rod with extension rod with extension rod with TiN coated contact points Remarks — — with extension rod with extension rod with extension rod with extension rod with extension rod *.0001” graduation 368-901-10 368-913 368-915 C-5 Holtest (Type ll) SERIES 368 — Three-Point Internal Micrometers FEATURES •With Ratchet Stop for constant force. •Setting Rings for origin point settings are optional. •Supplied in fitted plastic case up to 100mm / 4”. Over 100mm / 4” supplied in wooden case. •The Holtests (type II) have three contact points made of alloyed steel. •Measurement can be taken closer to the bottom of the blind bore (up to 100mm / 4”models). •Can measure deep holes using an Extension Rod (optional). Technical Data Graduation: 0.001mm or .0002" Measuring method: Three-point method Contact point: Hardening Steel (over HRC 60) Optional Accessories 368-770 368-869 DIMENSIONS AND MASS 368-774 Unit: mm C-6 Mass (g) 150 150 260 280 290 330 440 450 560 570 1020 1110 1200 1300 1420 1540 1690 1860 Measuring a Blind Hole The measuring contact points held in the jaws permit measuring the diameter of a blind hole right down to the bottom (up to 100mm / 4”models). L L 82 82 94 94 98 98 102 102 105 105 161 161 161 161 161 161 161 161 > Range 12 - 16mm / .5 - .65” 16 - 20mm / .65 - .8" 20 - 25mm / .8 - 1" 25 - 30mm / 1 - 1.2" 30 - 40mm / 1.2 - 1.6" 40 - 50mm / 1.6 - 2" 50 - 63mm / 2 - 2.5" 62 - 75mm / 2.5 - 3" 75 - 88mm / 3 - 3.5" 87 - 100mm / 3.5 - 4" 100 - 125mm / 4 - 5" 125 - 150mm / 5 - 6" 150 - 175mm / 6 - 7" 175 - 200mm / 7 - 8" 200 - 225mm / 8 - 9" 225 - 250mm / 9 - 10" 250 - 275mm / 10 - 11" 275 - 300mm / 11 - 12" Range 12 - 20mm / .5 - .8" 20 - 30mm / .8 - .12" 30 - 50mm / 1.2 - 2" 50 - 100mm / 2 - 4" 100 - 300mm / 4 - 12" a 2.6 3.4 3.4 3.4 19.6 b 3.5 5.2 10 14 13.8 952621: Extension rod 150mm / 5.9” For range 12-20mm / .5 - .8” models 952622: Extension rod 150mm / 5.9” For range 20-50mm / .8 - 2” models 952623: Extension rod 150mm / 5.9” For range 50-300mm / 2 - 12” models SPECIFICATIONS Metric Carbide ball Carbide pin Cone Contact point Range 12 - 16mm 16 - 20mm 20 - 25mm 25 - 30mm 30 - 40mm 40 - 50mm 50 - 63mm 62 - 75mm 75 - 88mm 87 - 100mm 100 - 125mm 125 - 150mm 150 - 175mm 175 - 200mm 200 - 225mm 225 - 250mm 250 - 275mm 275 - 300mm Inch Individual Order No. 368-764 368-765 368-766 368-767 368-768 368-769 368-770 368-771 368-772 368-773 368-774 368-775 368-776 368-777 368-778 368-779 368-780 368-781 Accuracy ±2µm ±2µm ±3µm ±3µm ±3µm ±3µm ±3µm ±3µm ±3µm ±3µm ±5µm ±5µm ±5µm ±5µm ±5µm ±5µm ±5µm ±5µm Range .5 - .65" .65 - .8" .8 - 1" 1 - 1.2" 1.2 - 1.6" 1.6 - 2" 2 - 2.5" 2.5 - 3" 3 - 3.5" 3.5 - 4" 4 - 5" 5 - 6" 6 - 7" 7 - 8" 8 - 9" 9 - 10" 10 - 11" 11 - 12" Individual Order No. 368-864 368-865 368-866 368-867 368-868 368-869 368-870 368-871 368-872 368-873 368-874 368-875 368-876 368-877 368-878 368-879 368-880 368-881 Accuracy ±.0001" ±.0001" ±.00015" ±.00015" ±.00015" ±.00015" ±.00015" ±.00015" ±.00015" ±.00015" ±.00025" ±.00025" ±.00025" ±.00025" ±.00025" ±.00025" ±.00025" ±.00025" Complete Unit Set Each set includes complete gages (micrometer head units and measuring heads for each size). Metric Range 12 - 20mm 20 - 50mm 50 - 100mm 100 - 200mm Order No. 368-991 368-992 368-993 368-994 Individual range 12-16, 16-20mm 20-25, 25-30, 30-40, 40-50mm 50-63, 62-75, 75-88, 87-100mm 100-125, 125-150, 150-175, 175-200mm Setting rings included ø16mm ø25mm, ø40mm ø62mm, ø87mm ø125mm, ø175mm Remarks with extension rod with extension rod with extension rod with extension rod Order No. 368-995 368-996 368-997 368-998 Individual range .5-.65", .65-.8" .8-1", 1-1.2", 1.2-1.6", 1.6-2" 2-2.5", 2.5-3", 3-3.5", 3.5-4" 4-5", 5-6", 6-7", 7-8" Setting rings included .65" DIA. 1" DIA., 1.6" DIA. 2.5" DIA., 3.5" DIA. 5" DIA., 7" DIA. Remarks with extension rod with extension rod with extension rod with extension rod Inch Range .5" - .8" .8" - 2" 2" - 4" 4" - 8" 368-991 368-992 368-993 368-994 C-7 Borematic SERIES 568 — ABSOLUTE Digimatic Snap Bore Gages FEATURES The Borematic enables the operator to take measurements more accurately and quicker than ever before. Once the origin point is set with the ORIGIN button, the Borematic retains the setting for the entire battery life. Therefore no longer repeated origin setting (presetting) is necessary. •TiN-coated measuring contact points provide excellent durability and impact resistance and allow the instrument to measure to the bottom of a blind hole. •Large LCD digits of 8.5mm height for error-free reading. •330-degree rotatable display unit for easy reading at any angle. •GO/NO-GO judgment function. •The ABSOLUTE linear encoder eliminates over-speed errors. •With SPC data output. •Setting rings for origin point setting are optional. •Can measure deep holes by attaching an optional extension rod. •Measurement can be taken closer to the bottom of a blind bore. •Supplied in fitted wooden case. Technical Data Accuracy: Refer to the list of specifications. (Excluding Quantizing Error) Resolution: 0.001mm or .00005"/0.001mm Contact point: Carbide orTiN coating* (*over 12mm/.5" models) Measuring method: Three-point method Display: LCD Battery: SR44 (1 pc.) (938882) Battery life: Approx. 1 year Functions Zero/ABS, presetting, GO/NO-GO judgment, power on/off, inch/mm conversion (on inch/metric models only), SPC data output, data hold Optional Accessories 568-333 TiN coated contact points ("-10" suffix models only) 568-438-10 Individual SPECIFICATIONS Inch/Metric Metric Individual Range Order No. 6 - 8mm 568-331 8 - 10mm 568-332 10 - 12mm 568-333 12 - 16mm 568-334-10 16 - 20mm 568-335-10 20 - 25mm 568-336-10 25 - 30mm 568-337-10 30 - 40mm 568-338-10 40 - 50mm 568-339-10 50 - 63mm 568-340-10 62 - 75mm 568-341-10 75 - 88mm 568-342-10 87 - 100mm 568-343-10 100 - 113mm 568-344-10 112 - 125mm 568-345-10 50 - 75mm 568-346-10 75 - 100mm 568-347-10 100 - 125mm 568-348-10 Accuracy ±5µm ±5µm ±5µm ±5µm ±5µm ±6µm ±6µm ±6µm ±6µm ±6µm ±6µm ±6µm ±6µm ±6µm ±6µm ±6µm ±6µm ±6µm Mass (g) 480 485 485 475 480 540 555 565 610 730 740 790 800 900 910 780 850 970 Carbide with TiN coated contact points Range Order No. .275 - .350" / 6.985 - 8.89mm .350 - .425" / 8.89 - 10.795mm .425 - .5" / 10.795 - 12.7mm .50 - .65" / 12.7 - 16.51mm .65 - .80" / 16.51 - 20.32mm .8 - 1.0" / 20.32 - 25.4mm 1.0 - 1.2" / 25.4 - 30.48mm 1.2 - 1.6" / 30.48 - 50.8mm 1.6 - 2.0" / 40.64 - 50.8mm 2.0 - 2.5" / 50.8 - 63.5mm 2.5 - 3.0" / 63.5 - 76.2mm 3.0 - 3.5" / 76.2 - 88.9mm 3.5 - 4.0" / 88.9 - 101.6mm 4.0 - 4.5" / 101.6 - 114.3mm 4.5 - 5.0" / 114.3 - 127mm 2.0 - 3.0" / 50.8 - 76.2mm 3.0 - 4.0" / 76.2 - 101.6mm 4.0 - 5.0" / 101.6 - 127mm 568-431 568-432 568-433 568-434-10 568-435-10 568-436-10 568-437-10 568-438-10 568-439-10 568-440-10 568-441-10 568-442-10 568-443-10 568-444-10 568-445-10 568-446-10 568-447-10 568-448-10 C-8 Accuracy Mass (g) ±.00025" 480 ±.00025" 485 ±.00025" 485 ±.00025" 475 ±.00025" 480 ±.0003" 540 ±.0003" 555 ±.0003" 565 ±.0003" 610 ±.0003" 730 ±.0003" 740 ±.0003" 790 ±.0003" 800 ±.0003" 900 ±.0003" 910 ±.0003" 780 ±.0003" 850 ±.0003" 970 937387: 965013: SPC cable (1m / 40”) SPC cable (2m / 80”) 952322: Extension rod 100mm / 3.94” For range 6-12mm / .275-.5” models 952621: Extension rod 150mm / 5.9” For range 12-20mm / .5" - .8” models 952622: Extension rod 150mm / 5.9” For range 20-50mm / .8" - 2” models 952623: Extension rod 150mm / 5.9” For range 50-300mm / 2"-12” models ––––: Setting ring (See page C-30.) Complete Unit Set Each set includes complete gages display units and measuring heads for each size and extension rod. Metric Carbide with TiN coated contact points Range 6 - 12mm 12 - 25mm 25 - 50mm 50 - 75mm 75 - 100mm 50 - 100mm Set Order No. Individual Order No. 568-981 568-331, 568-332 568-333 568-982-10 568-334-10, 568-335-10 568-336-10 568-983-10 568-337-10, 556-338-10 568-339-10 568-984-10 568-340-10 568-341-10 568-985-10 568-342-10 568-343-10 568-986-10 568-346-10 568-347-10 Setting rings included 177-125 (ø8mm) 177-126 (ø10mm) 177-177 (ø16mm) 177-286 (ø20mm) 177-139 (ø25mm) 177-290 (ø40mm) 177-314 (ø62mm) 177-318 (ø87mm) 177-314 (ø62mm) 177-318 (ø87mm) 177-314 (ø62mm) 177-318 (ø87mm) *interchangeable contact points (4 sets) Inch/Metric Interchangeable Contact Head Set Range .275” - .5” / 6.985 - 12.7mm .5” - 1” / 12.7 - 25.4mm 1” - 2” / 25.4 - 50.8mm 2” - 3” / 50.8 - 76.2mm 3” - 4” / 76.2 - 101.6mm 2” - 4” / 50.8 - 101.6mm 568-971 Complete Unit Set Carbide Set Order No. Individual Order No. 568-987 568-431, 568-432 568-433 568-988-10 568-434-10, 568-435-10 568-436-10 568-989-10 568-437-10, 568-438-10 568-439-10 568-990-10 568-440-10 568-441-10 568-991-10 568-442-10 568-443-10, 568-992-10 568-446-10 568-447-10 with TiN coated contact points Setting rings included 177-179 (.35" DIA.) 177-283 (.425" DIA.) 177-182 (.65" DIA.) 177-287 (.8" DIA.) 177-289 (1.2" DIA.) 177-291 (1.6" DIA.) 177-315 (2.5" DIA.) 177-319 (3.5" DIA.) 177-315 (2.5" DIA.) 177-319 (3.5" DIA.) 177-315 (2.5" DIA.) 177-319 (3.5" DIA.) Interchangeable Head Set Each set includes one display unit with interchangeable measuring heads of the sizes specified and extension rod. Metric with TiN coated contact points Carbide 6 - 12mm Set Order No. Display Unit 568-971 568-012 12 - 25mm 568-972-10 568-012 25 - 50mm 568-973-10 568-012 216557 50 - 100mm 568-974-10 568-012 216558 50 - 100mm 568-975-10 568-012 216558 Range 568-983-10 Adaptor Individual Head No. Supplied 954595 952906 952907 952908 216556 04AZA719 04AZA720 216557 04AZA728 Setting rings included 177-125 (ø8mm) 177-126 (ø10mm) 177-177 (ø16mm) 177-286 (ø20mm) 04AZA729 04AZA737 04AZA738 04AZA750, 04AZA751, 04AZA752 04AZA753 04AZA044* 04AZA045* 177-139 (ø25mm) 177-290 (ø40mm) 177-314 (ø62mm) 177-318 (ø87mm) 177-314 (ø62mm) 177-318 (ø87mm) *interchangeable anvils (Total 4 sets) Inch/Metric DIMENSIONS Range Measuring a Blind Hole xnÊÈÇ® The measuring pins held in the jaws permit measuring the diameter of a blind hole right down to the bottom. Unit: mm .275” - .5” / 6.985 - 12.7mm .5” - 1” / 12.7 - 25.4mm Set Order No. 568-976 Display Unit 568-013 Adaptor Supplied 954595 568-977-10 568-013 216556 216557 > L V ÓäÓ Ón°x Carbide Range 6 - 12mm / .275 - .5” 12 - 20mm / .5 - .8" 20 - 30mm / .8 - 1.2" 30 - 50mm / 1.2 - 2" 50 - 125mm / 2 - 5" ( ): 50-125mm model L 83 53 59 67 75 a 2 0.3 0.3 0.3 0.3 b — 5.6 8.3 13 17 c 2.5 3.5 5.2 10 14 1” - 2” / 25.4 - 50.8mm 568-978-10 568-013 216557 2” - 4” / 76.2 - 101.6mm 568-979-10 568-013 216558 2” - 4” / 50.8 - 101.6mm 568-980-10 568-013 216558 with TiN coated contact points Individual Head No. Setting rings included 952909 952910 952911 04AZA721 04AZA722 04AZA730 177-179 (.35" DIA.) 177-283 (.425" DIA.) 04AZA731 04AZA739 04AZA740 04AZA754 04AZA755 04AZA756 04AZA757 04AZA938* 04AZA939* 177-289 (1.2" DIA.) 177-291 (1.6" DIA.) *interchangeable anvils (Total 4 sets) C-9 177-182 (.65" DIA.) 177-287 (.8" DIA.) 177-315 (2.5" DIA.) 177-319 (3.5" DIA.) 177-315 (2.5" DIA.) 177-319 (3.5" DIA.) Tubular Inside Micrometers SERIES 133 — Single Rod Type FEATURES •With locking clamp. •Zero point can be readjusted by rotating the micrometer head sleeve. A key wrench is supplied. •Clear, crisp graduations on the satin chrome finished micrometer head. •Carbide-tipped measuring faces. •Supplied in fitted plastic case. Over 200mm / 8” supplied in wooden case. Accuracy: Refer to the list of specifications. Graduation: 0.01mm or .001" Optional Accessories ––––: 133-143 133-147 133-144 133-148 133-145 133-149 133-146 133-150 133-151 133-152 SPECIFICATIONS Metric Range 50 - 75mm 75 - 100mm 100 - 125mm 125 - 150mm 150 - 175mm 175 - 200mm 200 - 225mm 225 - 250mm 250 - 275mm 275 - 300mm 300 - 325mm 325 - 350mm 350 - 375mm 375 - 400mm 400 - 425mm 425 - 450mm 450 - 475mm 475 - 500mm 500 - 525mm 525 - 550mm 550 - 575mm 575 - 600mm 600 - 625mm 625 - 650mm 650 - 675mm 675 - 700mm Individual Order No. 133-143 133-144 133-145 133-146 133-147 133-148 133-149 133-150 133-151 133-152 133-153 133-154 133-155 133-156 133-157 133-158 133-159 133-160 133-161 133-162 133-163 133-164 133-165 133-166 133-167 133-168 Metric Accuracy ±3µm ±4µm ±5µm ±5µm ±5µm ±5µm ±5µm ±6µm ±6µm ±6µm ±7µm ±7µm ±7µm ±8µm ±8µm ±8µm ±9µm ±9µm ±9µm ±10µm ±10µm ±10µm ±11µm ±11µm ±11µm ±12µm Range 700 - 725mm 725 - 750mm 750 - 775mm 775 - 800mm 800 - 825mm 825 - 850mm 850 - 875mm 875 - 900mm 900 - 925mm 925 - 950mm 950 - 975mm 975 - 1000mm Inch Range 2" - 3" 3" - 4" 4" - 5" 5" - 6" 6" - 7 7" - 8" 8" - 9" 9" - 10" 10" - 11" 11" - 12" C-10 Technical Data Individual Order No. 133-169 133-170 133-171 133-172 133-173 133-174 133-175 133-176 133-177 133-178 133-179 133-180 Individual Order No. 133-223 133-224 133-225 133-226 133-227 133-228 133-229 133-230 133-231 133-232 Accuracy ±12µm ±12µm ±13µm ±13µm ±13µm ±14µm ±14µm ±14µm ±15µm ±15µm ±15µm ±16µm Accuracy ±.00015" ±.0002" ±.00025" ±.00025" ±.00025" ±.00025" ±.00025" ±.0003" ±.0003" ±.0003" Setting ring (See page C-30.) 133-902 Metric Inch Micrometer set Range 50 - 150mm (4 pcs. set) Order No. 133-901 50 - 300mm (10 pcs. set) 133-902 Included in set •133-143, 133-144, 133-145, 133-146 •with fitted case •133-143, 133-144, 133-145, 133-146, 133-147, 133-148, 133-149, 133-150, 133-151, 133-152 •with fitted case Micrometer set Range 2" - 6" (4 pcs. set) Order No. 133-903 2" - 12" (10 pcs. set) 133-904 Included in set •133-223, 133-224, 133-225, 133-226 •with fitted case •133-223, 133-224, 133-225, 133-226, 133-227, 133-228, 133-229, 133-230, 133-231, 133-232 •with fitted case DIMENSIONS Unit: mm Range 3.5 133-143 / 133-223 ø8 ø15 ø8 SR10 3 37 SR10 Range ø15 ø8 SR10 133-144 / 133-224 ø8 3 37 3.5 SR10 Range a b ø18 ø8 47 SR10 ø8 SR10 Order No. 133-145 / 133-225 133-146 / 133-226 133-147 / 133-227 133-148 / 133-228 133-149 / 133-229 ı ı ı 133-180 / 133-232 C-11 L 100 125 150 175 200 ı ı ı 975 a 5 5 18 18 18 ı ı ı 18 b 3 3 15 15 15 ı ı ı 15 Inside Micrometers SERIES 141 — Interchangeable Rod Type FEATURES • Each interchangeable rod is marked with its measuring range. • The sizes of interchangeable rods can be adjusted with spacing collars. • Both micrometer head and furnished rods are satin-chrome finished throughout. •Supplied in fitted plastic case. Over 1000mm / 40” supplied in wooden case. • Wide range of ID measurements with interchangeable rods. Technical Data Metric Model Accuracy: ±(6+L/50)µm* *L=Maximum measuring length (mm) Fraction rounded up *R=Maximum measuring length (inch) Fraction rounded up Inch Model Accuracy: ±{.00024+ (.00004xR/2)}"* Graduation: 0.01mm or .001" Optional Accessories ––––: 141-101 Setting ring (See page C-30.) When using the extension rod DIMENSIONS Unit: mm ©{°xÊhole Óä°x Ó{ SPECIFICATIONS Metric Range 25 - 32mm 25 - 50mm 50 - 63mm 50 - 200mm 50 - 300mm 200 - 225mm 200 - 500mm 200 - 1000mm Order No. 141-001 / 141-003* 141-101 / 141-103* 141-025 / 141-027* 141-205 / 141-211* 141-206 / 141-212* 141-009 / 141-011* 141-117 141-118 Travel of micrometer head 7mm 7mm 13mm 13mm 13mm 25mm 25mm 25mm Remarks — with 2 rods — with 3 rods with 5 rods — with 3 rods with 8 rods Travel of micrometer head .25" .25" .5" .5" .5" 1" 1” 1” Remarks — with 2 rods — with 3 rods with 5 rods — with 3 rods with 8 rods *with carbide tipped face Inch Range 1" - 1.25" 1" - 2" 2" - 2.5" 2" - 8" 2" - 12" 8" - 9" 4” - 20” 4” - 40” Order No. 141-002 / 141-004* 141-102 / 141-104* 141-026 / 141-028* 141-208 / 141-214* 141-233 / 141-215* 141-010 / 141-012* 141-121 141-122 *with carbide tipped face C-12 ©n ©£È © £Ó Ó -,n 141-233 Digimatic Tubular Inside Micrometers SERIES 337 — Extension Rod Type / SERIES 339 — Extension Pipe Type FEATURES Technical Data •Wide range of ID measurements by combining extension rods (pipes) and anvils with the micrometer head. •The 339 Series uses highly-durable extension pipes. •Carbide-tipped measuring faces. •Supplied in wooden case. Metric Model Accuracy: ±(3+n+L/50)µm* *n=Number of rod, L=Maximum measuring length (mm), Fraction rounded up, Excluding quantizing error Inch Model Accuracy: ±{.00012+ (.00004xR/2)}"* *R=Maximum measuring length (inch) Fraction rounded up Resolution: Display: Battery: Battery life: 0.001mm or .0001"/0.001mm LCD SR44 (1 pcs.), 938882 Approx. 8 months under normal use 337-204 Function Zero/ABS, Data hold, Data output, Preset, inch/mm conversion (inch/mm models) Alarm: Low voltage, Counting value composition error Optional Accessories SPC cable (1m) SPC cable (2m) Setting ring (See page C-30.) 339-294 Metric Range 200 - 225mm 200 - 1000mm 200 - 1500mm Inch/Metric Range 8 - 9” 8 - 40" 8 - 60" Metric Range 200 - 225mm 200 - 1000mm 200 - 2000mm Extension rod type Order No. Travel of micrometer head 337-001 25mm 337-201 25mm 337-202 25mm Extension rods — 25mm, 50mm, 100mm (2 pcs.), 200mm , 300mm 25mm, 50mm, 100mm, 200mm, 300mm (3 pcs.) Extension rod type Order No. Travel of micrometer head 337-002 1” 337-203 1" 337-204 1" Extension rods — 1", 2", 4" (2 pcs.), 8", 12" 1", 2", 4", 8", 12" (3 pcs.) Extension pipe type Order No. Travel of micrometer head 339-001 25mm 339-291 25mm 339-292 25mm Extension pipes — 25mm, 50mm, 100mm, 200mm, 400mm 25mm, 50mm, 100mm, 200mm (2 pcs.), 400mm (3 pcs.) Inch/Metric Extension pipe type Order No. 339-002 339-293 339-294 Range 8 - 9” 8 - 40" 8 - 80" Travel of micrometer head 1” 1" 1" Extension pipes — 1", 2", 4", 8" , 16" 1", 2", 4", 8" (2 pcs.), 16" (3 pcs.) DIMENSIONS 18.5 3 47 4.8 4.5 2.5 15 34.5 47 ø23 ø16 ø4 ø18 35 Micrometer Head for Series 337 18.5 3 3 35 1.8 72 Micrometer Head for Series 339 ø8 72 ø18 52.9 Unit: mm 200 (8”) 200 (8”) 1.8 ø23 937387: 965013: ––––: ( ): Inch heads C-13 Tubular Inside Micrometers SERIES 137 — Extension Rod Type FEATURES •Wide range of ID measurements by combining extension rods (pipes) and anvils with the micrometer head. •Carbide-tipped measuring faces are available. •Supplied in fitted plastic case except 1500 mm / 60” come in wooden case. 137-011 Technical Data Metric Model Accuracy: ±(3+n+L/50)µm Inch Model Accuracy: ±{.00012+n+(.00004xR/2)}* L=Maximum measuring length (mm), Fraction rounded up R=Maximum measuring length (inch), Fraction rounded up Graduation: 0.01mm or .001" Optional Accessories ––––: 137-205 SPECIFICATIONS Metric Range 50 - 63mm 50 - 150mm 50 - 300mm 50 - 500mm 50 - 1000mm Extension rod type Order No. 137-011 / 137-013* 137-201 / 137-206* 137-202 / 137-207* 137-203 / 137-208* 137-204 / 137-209* Travel of micrometer head 13mm 13mm 13mm 13mm 13mm 50 - 1500mm 137-205 / 137-210* 13mm Extension rods — 13mm, 25mm, 50mm 13mm, 25mm, 50mm (2 pcs.), 100mm 13mm, 25mm, 50mm (2 pcs.), 100mm, 200mm 13mm, 25mm, 50mm (2 pcs.), 100mm, 200mm (2 pcs.), 300mm 13mm, 25mm, 50mm (2 pcs.), 100mm, 200mm (3pcs.), 300mm (2 pcs.) *with carbide tipped face Inch Range 2" - 2.5" 2" - 6" 2" - 12" 2" - 20" 2" - 40" 2" - 60" Extension rod type Order No. 137-012 / 137-014* 137-211 / 137-216* 137-212 / 137-217* 137-213 / 137-218* 137-214 / 137-219* 137-215 / 137-220* Travel of micrometer head .5" .5" .5" .5" .5" .5" *with carbide tipped face DIMENSIONS 50 (2”) 8 11 4.8 23 Unit: mm 3 ø4 ø4 1 SR10 1.5 ø15 1.7 M10x1 SR10 137-011 / 137-012 / 137-013 / 137-014 C-14 Extension rods — .5", 1", 2" .5", 1", 2" (2 pcs.), 4" .5", 1", 2" (2 pcs.), 4", 8" .5", 1", 2" (2 pcs.), 4", 8" (2 pcs.), 12" .5", 1", 2" (2 pcs.), 4", 8" (3 pcs.), 12" (2 pcs.) Setting ring (See page C-30.) Tubular Inside Micrometers SERIES 139 — Extension Pipe Type FEATURES •Supplied in fitted wooden case except 500 mm / 20” come in plastic case. •Wide range of ID measurements by combining extension pipes and anvils with the micrometer head. 139-177 Technical Data Metric Model Accuracy: • Series 139: ±(3+n+L/50)µm L=Maximum measuring length (mm), Fraction rounded up Inch Model Accuracy: • Series 139: ±{.00012+m+(.00004xR/2)}* R=Maximum measuring length (inch), Fraction rounded up Graduation: 0.01mm or .001" Optional Accessories ––––: Setting ring (See page C-30.) Metric Extension pipe type Order No. Travel of micrometer head 139-001 25mm 139-173 25mm 139-174 25mm 139-175 25mm 139-176 25mm 139-177 25mm Range 100 - 125mm 100 - 500mm 100 - 900mm 100 - 1300mm 100 - 1700mm 100 - 2100mm Inch Extension pipe type Range 4" - 5" 4" - 20" 4" - 36" 4" - 52" 4" - 68" 4" - 84" Order No. 139-002 139-178 139-179 139-180 139-181 139-182 Travel of micrometer head 1" 1" 1" 1" 1" 1" Extension pipes — 25mm, 50mm, 100mm, 200mm 25mm, 50mm, 100mm, 200mm, 400mm 25mm, 50mm, 100mm, 200mm, 400mm (2 pcs.) 25mm, 50mm, 100mm, 200mm, 400mm (3 pcs.) 25mm, 50mm, 100mm, 200mm, 400mm (4 pcs.) Extension pipes — 1", 2", 4", 8" 1", 2", 4", 8", 16" 1", 2", 4", 8", 16" (2 pcs.) 1", 2", 4", 8", 16" (3 pcs.) 1", 2", 4", 8", 16" (4 pcs.) 139-201 Inch Extension pipe type Range 1.5 - 2” 4 - 5” 1.5 - 12” 4 - 40” Order No. 139-004 139-006 139-201 139-202 Travel of micrometer head .5" 1" .5" 1" Extension pipes — — .5”, 1", 2", 2.5”, 3”, 3.5”, 4", 6" 1", 2", 3", 6", 9", 12", 14", 16", 17", 19” Remarks — — Includes 139-004 Includes 139-006 DIMENSIONS Unit: mm Unit: inch 100 to 125 (4-5”) 47 3 139-004 139-006 ø8 ø8 ø18 ø16 4.5 SR10 139-001 / 139-002 C-15 SR10 Tubular Inside Micrometers SERIES 140 — Extension Pipe Type FEATURES Technical Data •Wide range of ID measurements by combining extension rods (pipes) and anvils with the micrometer head. •The Series 140 use highly-durable/ large-diameter extension pipes. •Supplied in fitted wooden case. Metric Model Accuracy: ±(3+n+L/50)µm* Inch Model Accuracy: ±{.00012+m+(.00004xR/2)}* *n=Number of rod, L=Maximum measuring length (mm), Fraction rounded up *n=Number of rod, L=Maximum measuring length (mm), Fraction rounded up Graduation: 0.01mm or .001" Metric Range 1000 - 2000mm 1000 - 3000mm 1000 - 4000mm 1000 - 5000mm Inch Extension pipe type Order No. Travel of micrometer head 140-157 50mm 140-158 50mm 140-159 50mm 140-160 50mm Extension pipe type Order No. 140-161 140-162 140-163 140-164 Range 40" - 80" 40" - 120" 40" - 160" 40" - 200" Travel of micrometer head 2" 2" 2" 2" Optional Accessories ––––: Setting ring (See page C-30.) Extension pipes 50mm, 100mm (2 pcs.), 200mm, 500mm 50mm, 100mm (2 pcs.), 200mm, 500mm, 1000mm 50mm, 100mm (2 pcs.), 200mm, 500mm, 1000mm (2 pcs.) 50mm, 100mm (2 pcs.), 200mm, 500mm, 1000mm (3 pcs.) Extension pipes 2", 4" (2 pcs.), 8", 20" 2", 4" (2 pcs.), 8", 20", 40" 2", 4" (2 pcs.), 8", 20", 40" (2 pcs.) 2", 4" (2 pcs.), 8", 20", 40" (3 pcs.) DIMENSIONS Unit: mm ø33 ø33 16.5 175.5 699 1000 to 1050 (40 to 42”) Micrometer Head for Series 140 C-16 ø21 ø19 SR10 ø8 ø32 ø8 101 15 SR10 Inside Micrometers SERIES 345, 145 — Caliper Type FEATURES Technical Data •Caliper type jaws are made of high-grade, tool steel. •Locking clamp for positive locking of spindle. Accuracy: Refer to the list of specifications. (excluding quantizing error for digital models) Resolution*: 0.01mm or .00005"/0.001mm Graduation**: 0.01mm or .001" Measuring faces: Carbide tipped Display*: LCD Battery*: SR44 (1 pc.), 938882 Battery life*:Approx. 8 months under normal use *Digital models •Satin-chrome finished. • A special holder is available to be used with Mitutoyo Micrometer Stand. •Supplied in fitted plastic case. Over 175mm / 4” supplied in wooden case. **Analog models Function of Digital Model Origin-set, Zero-setting, Data hold, Data output, inch/mm conversion (inch/mm models) Alarm: Low voltage, Counting value composition error 345-350 Optional Accessories 05CZA662: 05CZA663: ––––: 300401: 300400: SPC cable with data switch 1m / 40” SPC cable with data switch 2m / 80” Setting ring (See page C-30.) Cap for stand holder Stand holder 145-193 145-187 SPECIFICATIONS Inch/Metric Digital model Range Order No. Accuracy .2 - 1.2" / 5-30mm 345-350 ±.00025" 1 - 2" / 25-50mm 345-351 ±.0003" Metric Range 5 - 30mm 25 - 50mm Order No. 345-250 345-251 Accuracy ±5µm ±6µm Inch Metric Cap Range 5 - 30mm 25 - 50mm 50 - 75mm 75 - 100mm 100 - 125mm 125 - 150mm 150 - 175mm 175 - 200mm 200 - 225mm 225 - 250mm 250 - 275mm 275 - 300mm Holder DIMENSIONS Order No. 145-185 145-186 145-187 145-188 145-189 145-190 145-191 145-192 145-217 145-218 145-219 145-220 Range .2 - 1.2" 1 - 2" 2 - 3" 3 - 4" 4 - 5” 5 - 6” 6 - 7" 7 - 8” Accuracy ±5µm ±6µm ±7µm ±8µm ±9µm ±9µm ±10µm ±10µm ±11µm ±11µm ±12µm ±12µm Order No. 145-193 145-194 145-195 145-196 145-197 145-198 145-199 145-200 Accuracy ±.00025" ±.0003" ±.00035" ±.0004" ±.00045" ±.00045" ±.0005" ±.0005" 145-186 / 145-194 4.3 27.5 27.5 145-185 / 145-193 R12 9.3 ø8 4.3 R2.2 9.3 3 R12 R12 ø2 12.5 ø2 27.5 4.5 R2.2 R12 9.3 9.3 31.4 12.5 3 Unit: mm Over 50mm / 2” Models. C-17 Inside Micro Checker SERIES 515 FEATURES •The Inside Micro Checker is designed to efficiently check the zero point of a tubular inside micrometer. •Each measuring block is made of zirconia-based ceramic and it is free from deterioration and dimensional changes over time. 515-585 Technical Data Block pitch accuracy: ±(0.001+L/150000)mm* *L= Length to check (mm) Optional Accessories 602160: 602163: Standard accessory SPECIFICATIONS Order No. 515-585 515-586 Range 300mm 600mm Length to check 25, 50, 75, 100, 125, 150, 175, 200, 225, 250, 275, 300mm 25, 50, 75, 100, 125, 150, 175, 200, 225, 250, 275, 300, 325, 350, 375, 400, 425, 450, 475, 500, 525, 550, 575, 600mm DIMENSIONS Unit: mm ÎÈ{ x£xxnx È£ x£ Î{ä xä ÈÈ{ È{ä x£ È£ x£xxnÈ xä C-18 Wooden case for 300mm Inside Micro Checker Wooden case for 600mm Inside Micro Checker Bore Gages SERIES 511 — for Small Holes FEATURES •Its interchangeable anvils are made of alloyed steel. •The dial indicator is fully protected by a rugged cover. SPECIFICATIONS Gage Stem ø 8mm Metric Order No. Order No. Order No. Without Dial Gage With 2046SB With 2109SB-10 Graduation 0.01mm Graduation 0.001mm 6 - 10mm 511-209* 511-211 511-210 10 - 18.5mm 511-201* 511-204 511-203 Measuring Range Number Number of Anvils of Spacers 9 9 1 1 *Does not come supplied with Dial Gage Protector Cover ( 21DZA000 ) Inch Gage Stem Dia .375” Measuring Range Order No. Order No. Without Dial Gage With 2922SB Graduation .0005” .24 - .4” .4 - .74” 511-214* 511-205* 511-213 511-207 Order No. With 2923SB-10 Graduation .0001" 511-212 511-206 Number Number of Anvils of Spacers 9 9 1 1 *Does not come supplied with Dial Gage Protector Cover ( 21DZA000 ) 511-204 Technical Data Accuracy: 5µm / .0002” Indication stability: 2µm / .00008” Graduation: 0.01mm, 0.001mm, .0005” or .0001" DIMENSIONS Measuring Heads Unit: mm 5 50 53 27 80 ø4 3.7 Anvil 100 Anvil 6 - 10mm / .24 - .4” range model 6 - 10mm .24 - .4” 10 - 18.5mm .4 - .74” R0.5 ø6 5 8.5 10 - 18.5mm / .4 - .74” range model Optional Accessories 21DZA000: Dial Gage Protector Cover – – – – : Setting ring (See page C-30.) C-19 Bore Gages SERIES 511 FEATURES Mitutoyo offers a complete selection of Bore Gages, all of them with interchangeable anvils and necessary accessories to perform close tolerance ID measurements. •Most popular Bore Gages. •Carbide-tipped contact points for durability. •The dial indicator is fully protected by a rugged cover. •Optional extension rods can be attached for measuring deep holes. SPECIFICATIONS Metric Gage Stem ø 8mm Measuring Range Order No. Order No. Number Order No. Without Dial Gage With 2046SB of Anvils With 2109SB-10 Graduation 0.01mm Graduation 0.001mm Number of Spacers 18 - 35mm 511-126 * 511-171 511-167 9 2 35 - 60mm 511-127* 511-172 511-168 9 4 50 - 100mm 511-128* 511-173 511-169 11 4 50 - 150mm 511-132* 511-174 511-170 11 4 50mm Sub-Anvil 100 - 160mm 511-129* 511-175 511-178 13 4 160 - 250mm 511-130* 511-176 511-179 6 7 250 - 400mm 511-131* 511-177 511-180 5 7 75mm Sub-Anvil 18 - 150mm — 511-901 3 pcs. / set 511-902 3 pcs. / set 26 pcs. 7 50mm Sub-Anvil *Does not come supplied with Dial Gage Protector Cover ( 21DZA000 ) Inch Gage Stem Dia .375” Measuring Range Order No. Without Dial Gage .7 - 1.4" 1.4 - 2.5" 2 - 6" 511-104* 511-105* 511-107* 4 - 6.5" 6.5 - 10" 10 - 16" .7" - 6" 511-181* 511-182* 511-183* Order No. With 2922SB Graduation .0005” 511-159 511-160 511-162 Order No. With 2923SB-10 Graduation .0001" 511-163 511-164 511-166 511-184 511-185 511-186 511-911 (set) 511-187 511-188 511-189 511-912 (set) Number of Anvils Number of Spacers 8 pcs. 6 pcs. 11 pcs. 3 4 4 2" Sub-Anvil 13 pcs. 6 pcs. 5 pcs. 25 pcs 4 6 6 511-173 2" Sub-Anvil *Does not come supplied with Dial Gage Protector Cover ( 21DZA000 ) Technical Data Accuracy: 5µm / .0002” Indication stability: 2µm / .00008” Graduation: 0.01mm, 0.001mm, .0005" or .0001" C-20 Optional Accessories 953549: 125mm / 4.92” Extension rod for 18-35mm / .7 -1.4" models 953552: 125mm / 4.92” Extension rod for 35-160mm / 1.4 - 6.5" models 953557: 125mm / 4.92” Extension rod for 160-400mm / 6.5 - 16" models 953550: 250mm / 9.84” Extension rod for 18-35mm / .7 - 1.4" models 953553: 250mm / 9.84” Extension rod for 35-160mm / 1.4 - 6.5" models 952361: 250mm / 9.84” Extension rod for 160-400mm / 6.5 - 16" models 953551: 500mm / 19.69” Extension rod for 18-35mm / .7 - 1.4" models 953554: 500mm / 19.69” Extension rod for 35-160mm / 1.4 - 6.5" models 953558: 500mm / 19.69” Extension rod for 160-400mm / 6.5 - 16" models 953555: 750mm / 29.53" Extension rod for 35-160mm / 1.4 - 6.5" models 953559: 750mm / 29.53” Extension rod for 160-400mm / 6.5 - 16" models 953556: 1000mm / 39.37” Extension rod for 35-160mm / 1.4 - 6.5" models 953560: 1000mm / 39.37” Extension rod for 160-400mm / 6.5 - 16" models Contact Point 18 - 35mm / .7 - 1.4” 35 - 60mm / 1.4 - 2.5” 50 - 100mm / 2 - 4” 100 - 160mm / 4 - 6” 160 - 250mm / 6 - 10” 250 - 400mm / 10 - 16” DIMENSIONS 104 Unit: mm 80 11.2 ø8.7 Anvil 18 - 35mm / .7 - 1.4” 105 ø12.7 6.4 SR0.75 150 80 ø12 A 35 - 160mm / 1.4 - 6” 104 Anvil Anvil SR1 9 0 B ø2 35 - 60mm / 1.4 - 2.5” 88.5 ø15 ø12.8 250 124 160 - 400mm / 6 - 16” Setting ring (See page C-30.) 89 13 SR1.5 ø19.8 C-21 80 Bore Gages SERIES 511 — Short Leg Type FEATURES •Compact and lightweight because of the short length below the grip. •Carbide-tipped contact point for durability. SPECIFICATIONS Gage Stem ø 8mm Metric Measuring Range Order No. With 2046SB Graduation 0.01mm Order No. Number of Anvils Number of With 2109SB-10 Spacers Graduation 0.001mm 511-461 511-462 511-463 511-464 511-465 18 - 35mm 35 - 60mm 50 - 100mm 50 - 150mm 100 - 160mm 511-471 511-472 511-473 511-474 511-475 9 6 11 11 13 2 4 4 4 4 511-461 Technical Data Inch Gage Stem Dia. .375” Measuring Range Order No. With 2922SB Graduation .0005" .7 - 1.4" 511-481 1.4 - 2.5" 511-482 2 - 4" 511-483 2 - 6" 511-484 4 - 6.5" 511-485 Order No. With 2923SB-10 Graduation .0001" 511-491 511-492 511-493 511-494 511-495 Accuracy: 5µm / .0002” Indication stability: 2µm / .00008” Graduation: 0.01mm, 0.001mm, .0005” or .0001" Number of Anvils Number of Spacers 8 6 11 11 13 3 4 4 4 4 Contact Point 18 - 35mm / .7 - 1.4” 35 - 60mm / 1.4 - 2.5” DIMENSION 50 ø8.7 Anvil Unit: mm 80 50 - 100mm / 2 - 4” 11.2 18 - 35mm / .7 - 1.4” 105 6.4 SR0.75 ø12.7 50 104 80 Anvil a ø12 50 - 150mm / 2 - 6” 9 SR1 b 35 - 60mm / 1.4 - 2.5” 50 - 100mm / 2 - 4” 50 - 150mm / 2 - 6” 100 - 160mm / 4 - 6.5” 0 ø2 ø12.8 Range 35 - 60mm / 1.4 - 2.5” 50 - 100mm / 2 - 4” 50 - 150mm / 2 - 6” 100 - 160mm / 4 - 6.5” a 17.5 26 26 39 b — 37.8 37.8 46.4 100 - 160mm / 4 - 6.5” Optional Accessories ––––: C-22 Setting ring (See page C-30.) Bore Gages SERIES 511 — for Blind Holes FEATURES •Can measure ID at position close to the bottom of blind holes. SPECIFICATIONS Metric Gage Stem ø 8mm Measuring Range Order No. Order No. Without Dial Gage With 2046SB Graduation 0.01mm 511-412 Order No. Number of Anvils Number of With 2019SB-10 Spacers Graduation 0.001mm 15 - 35mm 511-401* 511-411 511-421 35 - 60mm 50 - 100mm 50 - 150mm 511-402* 511-403* 511-404* 511-412 511-413 511-414 511-422 511-423 511-424 11 10mm Sub-Anvil 6 11 11 50mm Sub-Anvil 1 4 4 4 *Does not come supplied with Dial Gage Protector Cover (21DZA000) Inch Gage Stem Dia. .375” Measuring Range Order No. Order No. Without Dial Gage With 2922SB Graduation .0005" .6 - 1.4" 511-406* 511-431 Technical Data Accuracy: 5µm / .0002” Indication stability: 2µm / .00008” Graduation: 0.01mm, 0.001mm, .0005” or .0001" 511-432 511-433 511-434 511-442 511-443 511-444 Number of Anvils Number of Spacers 11 .4" Sub-Anvil 6 11 11 2" Sub-Anvil 1 4 4 4 *Does not come supplied with Dial Gage Protector Cover (21DZA000) Contact Point 511-401 511-407* 511-408* 511-409* 1.4 - 2.4" 2 - 4" 2 - 6" Order No. With 2923SB-10 Graduation .0001" 511-441 511-403 DIMENSIONS Unit: mm £äx £xä > ©n°Ç Ó°x Û L Ó°x Optional Accessories – – – – : Setting ring (See page C-30.) Extension Rods are not available for these models ,£ Range 15 - 35mm / .6 - 1.4” 35 - 60mm / 1.4 - 2.4” 50 - 100mm / 2 - 4” 50 - 150mm / 2 - 6” a 9.7 14.7 23.7 23.7 b 10 18 22 22 C-23 nä Bore Gages SERIES 511 — with Micrometer Head FEATURES •Interchangeable anvil is attached to a micrometer head for accurate dimensional setting. •Wide measuring range with sub-anvils. •Carbide ball contact point for durability. •Extension rods (optional) can be attached for measuring deep holes. •Optional Setting Rings offer the best method of zero-setting Bore Gages. SPECIFICATIONS Metric Gage Stem ø 8mm Measuring Range Order No. Order No. Without Dial Gage With 2046SB Graduation 0.01mm Order No. Mic Head With 2019SB-10 Travel Graduation 0.001mm Extensions Mic Head 5mm, 10mm, 15mm, 20mm 10mm, 20mm 10mm, 20mm, 20mm 25mm, 50mm 50mm, 50mm 50mm, 100mm 500mm, 100mm 35 - 60mm 511-341* 511-344 511-343 5mm 60 - 100mm 100 - 160mm 511-331* 511-301* 511-334 511-312 511-333 511-311 10mm 13mm 150 - 250mm 250 - 400mm 400 - 600mm 600 - 800mm 511-302* 511-303* 511-304* 511-305* 511-314 511-316 511-318 511-328 511-313 511-315 511-317 511-327 25mm 50mm 50mm 50mm 511-334 *Does not come supplied with Dial Gage Protector Cover (21DZA000) Inch Accuracy: 5µm / .0002” Indication stability: 2µm / .00008” Graduation: 0.01mm, 0.001mm, .0005” or .0001" Gage Stem Dia. .375” Measuring Range Order No. Order No. Without Dial Gage With 2922SB Graduation .0005" 1.4 - 2.5" 511-342* 511-345 2.4 - 4"" 511-332* 511-335 4 - 6.4" 511-306* 511-325 6 - 10" 511-307* 511-319 10 - 16" 511-308* 511-321 16 - 24" 511-309* 511-323 24 - 32" 511-310* 511-329 *Does not come supplied with Dial Gage Protector Cover (21DZA000) C-24 Technical Data Order No. With 2923SB-10 Graduation .0001" 511-346 511-336 511-326 511-320 511-322 511-324 511-330 Mic Head Travel Extensions Mic Head .2” .4” .5” 1” 2” 2” 2” .2”, .4”, .6”, .8” .4”, .8” .4”, .8”, .8” 1”, 2” 2”, 2” 2”, 4” 2”, 4” Optional Accessories 953549: 125mm / 4.92” Extension rod for 18-35mm / .7 -1.4" models 953552: 125mm / 4.92” Extension rod for 35-160mm / 1.4 - 6.5" models 953557: 125mm / 4.92” Extension rod for 160-400mm / 6.5 - 16" models 953550: 250mm / 9.84” Extension rod for 18-35mm / .7 - 1.4" models 953553: 250mm / 9.84” Extension rod for 35-160mm / 1.4 - 6.5" models 952361: 250mm / 9.84” Extension rod for 160-400mm / 6.5 - 16" models 953551: 500mm / 19.69” Extension rod for 18-35mm / .7 - 1.4" models 953554: 500mm / 19.69” Extension rod for 35-160mm / 1.4 - 6.5" models 953558: 500mm / 19.69” Extension rod for 160-400mm / 6.5 - 16" models 953555: 750mm / 29.53" Extension rod for 35-160mm / 1.4 - 6.5" models 953559: 750mm / 29.53” Extension rod for 160-400mm / 6.5 - 16" models 953556: 1000mm / 39.37” Extension rod for 35-160mm / 1.4 - 6.5" models 953560: 1000mm / 39.37” Extension rod for 160-400mm / 6.5 - 16" models Contact Point 35 - 60mm / 1.4 - 2.5” 60 - 100mm / 2.4 - 4” 100 - 160mm / 4 - 6” 150 - 250mm / 6 - 10” 250 - 400mm / 10 - 16” 400 - 600mm / 16 - 24” 600 - 800mm / 24 - 32” DIMENSIONS Unit: mm V L nä ` > i Óä v } ÎxÊÊÈä Range 35 - 60mm / 1.4 - 2.5” 60 - 100mm / 2.4 - 4” 100 - 160mm / 4 - 6” 150 - 250mm / 6 - 10” 250 - 400mm / 10 - 16” 400 - 600mm / 16 - 24” 600 - 800mm / 24 - 32” a 150 150 150 250 250 250 250 b 105 105 105 124 124 124 124 C-25 c SR8 SR8 SR10 SR10 SR10 SR10 SR10 d 11.9 26 39 60 88.5 200 300 e SR0.75 SR1 SR1 SR1.5 SR1.5 SR1.5 SR1.5 f 6.5 9 9 13 13 16 16 g — 37.8 46.4 78 89 120 120 h — ø12.8 ø12.8 ø19.8 ø19.8 ø19.8 ø19.8 i ø8.7 ø12 ø12 ø15 ø15 ø15 ø15 ABSOLUTE Digimatic Bore Gage SERIES 511 FEATURES This ABSOLUTE Digimatic bore gage is exclusively designed for ID measurement. •The minimum value holding function provides the easy detection of hole diameter. Technical Data Accuracy: Wide Range: 0.003mm / .00012” Narrow Range: 0.002mm / .00008” (Excluding Quantizing Error) Resolution: .00005" / 0.001mm Display: LCD Battery: SR44 (1 pc.) (938882) Battery life: Approx. 9 months for normal use Dust/Water protection level: Conforming to IP53 Functions •Up to three sets of master value and upper/lower tolerance value can be memorized. •An analog bar indicator is integrated to enhance the intuition in reading. •GO/±NG judgment is performed by setting the upper and lower tolerances. •Up to four rods (250mm or 500mm) can be used. 511-521 Origin-set, Zero-Setting, Presetting, Power on/off, inch/mm conversion (inch/mm type only), Data output, GO/±NG tolerance judgment Alarm: Low battery voltage, scale contamination, over-flow error, tolerance limit setting error Optional Accessories 21DZA089: Extension rod 250 mm (10") 21DZA081: Extension rod 500 mm (20") 516-118-10:Origin setup metric rectangular gage block set 516-119-10:Origin setup metric square gage block set 516-120-26:GB calibration kit for series 511 bore gage. (9 pcs GB and plain jaw, 160mm holder) 905338: SPC cable (40” / 1m) 905409: SPC cable (80” / 2m) – – – – : Setting ring (See page C-30.) SPECIFICATIONS Inch/Metric Range 1.8 - 4" / 45 - 100mm Order No. Probe depth 511-521 6" (152.4mm) DIMENSIONS AND MASS Unit: mm Ó°{ ÎÓäc äc ÓÈÝ£°x ÓÎÓÊ{nÓ® ÓÈn°xÊx£n°x® ©ÓÓ Origin setup gage block set £xä Îä Ón Ón £°x Óä ©Îä ÓxäÊxää® Îΰx® ÎÓäc £ää £xä ©Ón £È°x ©È£ ÊÊ®\ÊxääÊÌÞ«i ÊÓ -, ,ÊÓ - MASS: 500g C-26 Example: using four extension rods. Bore Gages SERIES 526 — for Extra Small Holes FEATURES These Bore Gages measure diameters of small holes. The radial displacement of split-ball contact is converted to axial displacement of measuring rod, which is shown on the dial indicator. SPECIFICATIONS Metric •Optional stand (215-120M) is available for efficient measurement of multiple small holes. Gage Stem ø 8mm Measuring Range Order No. Order No. Without Dial Gage With 2046SB Graduation 0.01mm 526-127 526-170* 526-160* 526-150* — — 0.95 - 1.55mm 1.5 - 4mm 3.7 - 7.3mm 7 - 10mm 10 - 18mm 526-173 526-163 526-153 526-126 526-127 Order No. Number With 2019SB-10 of Anvils Graduation 0.001mm Number of Probe depth Needles (D) 526-172 526-162 526-152 526-124 526-125 1 2 1 2 2 6 9 7 6 8 11.5mm 17.5, 22.5mm 32mm 56mm 62mm *Does not come supplied with Dial Gage Protector (21DZA000) 526-172 Inch Technical Data Accuracy: 4µm / .00016” Indication stability: 2µm / .00008” Graduation: 0.01mm, 0.001mm, .0005” or .00001" Contact Point Gage Stem Dia .375” Measuring Range Order No. Order No. With Without Dial Gage 2923SB-10 Graduation .0001" .037 - .061" 526-175* 526-176 .06 - .157" 526-165* 526-166 .145 - .29" 526-155* 526-156 Number of Anvils Number of Needles Probe depth (D) 5 9 7 1 2 1 .45" .68", .89" 1.26" *Does not come supplied with Dial Gage Protector (21DZA000) DIMENSIONS *ÀLi £ÉÓ± Unit: mm £ä® È È°x {x ÓÈ°x nä £ÉÓ± ©n Ì>VÌÊ«Ì Ì>VÌ «Ì £ä® È® n x Optional Accessory £È°x {x ÓÇ nä xÝä°x ÇÝä°Çx® Ì>VÌ «Ì ©n Ç n® 215-120M: Bore gage stand ©n È ÇÝä°Çx Dial Faces + 0 _ 5 15 1 0 20 Setting ring (See page C-30.) 10 NO. 2922-08 2 3 SHOCK MADE 25 2922SB .0005” ® PROOF IN + 0 1 .0005" 10 ––––: 5 JAPAN 20 15 1 3 .0001" 2 1 0 3 4 2 3 2 ® 4 6 JEWELS 5 5 _ 1 0 +1 _ 3 2 1mm 4 5 6 .8 10 7 4 2923SB-10 .0001” 2 8 .6 .4 .2 JEWELED 6 0 9 10 9 8 2109SB-10 0.001mm C-27 4 5 NO.1011-11 7 0 90 3 10 0.01" 80 70 1 0 4 5 9 2 8 7 3 60 20 Shock 6 50 40 2046SB 0.01mm 30 Dial Bore Gages SERIES 545 — Rugged, Production-Line Tools Anvils FEATURES •Carbide-tipped contact point for excellent durability. •Wide range of measurements with interchangeable Anvil Extensions (screw-in type). •Carbide-tipped anvil is optional (901484). •Two guide pins ensure high repeatability of measurements. •Easy zero adjustment because the Dial Bore Gage can stand upright. •Optional interchangeable rods provide a variety of probe depths. SPECIFICATIONS Metric Measuring Range 35 - 50mm 50 - 75mm 75 - 150mm Order No. Graduation 0.001mm 545-114S 545-115S 545-116S Number of Anvils 5 5 7 Inch Measuring Range 1.475 - 2.075" 1.975 - 3.075" 2.975 - 6.075" Order No. Graduation .0005" 545-124S 545-125S 545-126S Order No. Graduation .0001" 545-134S 545-135S 545-136S Number of Anvils 6 5 7 Technical Data 545-125S Accuracy: 5mm / .0002” Indicator Stability: 3mm / .00012” Graduation: 0.001mm, .0005” or .0001" Optional Accessories 901484:Carbide-tipped anvil 901529:Interchangeable rod (Probe depth: 85mm / 3.5”) 901530:Interchangeable rod (Probe depth: 115mm / 4.5”) 901940:Interchangeable rod (Probe depth: 150mm / 5.9”) 901531:Interchangeable rod (Probe depth: 265mm / 10.4”) 901532:Interchangeable rod (Probe depth: 315mm / 12.4”) 901533:Interchangeable rod (Probe depth: 390mm / 15.4”) DIMENSIONS AND MASS > ©ÓÇ ä ©Îä ©È L È ` V Unit: mm ÌiÀV >}i>LiÊÀ` Range Û 35 - 50mm / 1.475" - 2.075" L 240 a 123 b 88 c 35 d 50 Mass (g) 480 50 - 75mm / 1.975" - 3.075" 265 148 113 50 75 540 75 - 150mm / 2.975" - 6.075" 305 188 153 75 150 650 ––––: C-28 Setting ring (See page C-30.) Standard Accessories 64AAA012: Master Plate 3”(W) x 2”(D) x .925”(H) 21BZA778: Black Leather Case 9.7”(W) x 2”(D) x 6.1”(H) 21BZA779*: Wooden box 12.8”(W) x 5.1”(D) x 3.63”(H) * 547-481 (DC1-2090) only Digimatic Chamfer Chek SERIES 547 - I.D. Measures the top diameter of tapered holes and chamfers O.D measures the minor end diameter of tapered conical parts Optional Accessories Setting Master Order No. Chamfer Chek I.D. 64AAA007 64AAA008 Model No. Diameter Accuracy SM-1000 ±.0002” SM-2000 *.375” / .750” (I.D.) *1.25” / 1.75” (I.D.) 9.525mm (I.D.) 19.05mm (I.D.) 64AAA133 64AAA134 Chamfer Chek O.D. 64AAA009 SM-1000E *.375” / .750” (O.D.) 905338: 905409: I.D. ±.0003” O.D. ±0.005mm ±0.008mm ±.0002” SPC cable (40” / 1m) SPC cable (80” / 2m) 547-480 547-482 547-480 Shown with optional setting master. SPECIFICATIONS Inch / Metric Resolution Chamfer Chek I.D. .0005”/0.01mm .0005”/0.01mm Chamfer Chek O.D. .0005”/0.01mm .0005”/0.01mm Diameter Range Order No. Model No. Accuracy Mass .02-1” / 0.5-25.4mm 1-2” / 25.4-50.8mm 547-480 547-481 DCI-1090 DCI-2090 ±.001” / ±0.025mm ±.001” / ±0.025mm 1.75lbs./793g 3.97lbs./1,800g DCO-0590 ±.001” / ±0.025mm 1.75lbs./793g DCO-1090 ±.001” / ±0.025mm 1.75lbs./793g 1/8”-1/2” / 3.18547-482 12.7mm 3/8”-1” / 9.52-25.4mm 547-483 526-007M-10 Digimatic Hole Chek SERIES 526 - Instant diameter measurement of small holes SPECIFICATIONS Inch / Metric Resolution .0005”/0.01mm Diameter Range .010” - .330" Order No. Model No. 526-007M-10 DHC-0133 Optional Accessories Setting Master Order No. 64AAA003 64AAA004 64AAA005 64AAA006 Model No. SM-040 SM-130 SM-230 SM-330 Diameter .029" .078” .178” .278” Accuracy ±.0002" ±.0002" ±.0002" ±.0002" Standard Accessories 21BZA778: Black Leather Case 9.7”(W) x 2”(D) x 6.1”(H) C-29 Accuracy ±.001” / ±0.025mm Mass 1.5lbs./680g Setting Ring SERIES 177 — Accessories for Inside Micrometers, Holtest and Dial Bore Gages FEATURES •Used for quick zero adjustment of dial bore gages, Holtest, and inside micrometers. •Actual inside diameter is marked on each ring. SPECIFICATION Setting Rings Metric Size Order No. Accuracy 1mm 1.1mm 1.2mm 1.3mm 1.4mm 1.75mm 2mm 2.25mm 2.5mm 2.75mm 3mm 3.25mm 3.5mm 3.75mm 4mm 4.5mm 5mm 5.5mm 6mm 6.5mm 7mm 8mm 10mm 12mm 14mm 16mm 17mm 20mm 25mm 30mm 35mm 40mm 45mm 50mm 60mm 62mm 70mm 75mm 80mm 87mm 90mm 100mm 125mm 150mm 175mm 200mm 225mm 250mm 275mm 300mm 177-220 177-222 177-225 177-227 177-230 177-236 177-239 177-242 177-208 177-246 177-248 177-250 177-252 177-255 177-204 177-257 177-205 177-263 177-267 177-271 177-275 177-125 177-126 177-284 177-132 177-177 177-133 177-286 177-139 177-288 177-140 177-290 177-178 177-146 177-292 177-314 177-147 177-316 177-294 177-318 177-148 177-296 177-298 177-300 177-302 177-304 177-306 177-308 177-310 177-312 ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±2.5µm ±2.5µm ±2.5µm ±2.5µm ±2.5µm ±2.5µm ±2.5µm ±2.5µm Outside Diameter 20mm 20mm 20mm 20mm 20mm 25mm 25mm 25mm 25mm 25mm 25mm 25mm 25mm 25mm 25mm 25mm 25mm 25mm 25mm 25mm 25mm 32mm 32mm 32mm 38mm 45mm 45mm 45mm 53mm 71mm 71mm 71mm 85mm 85mm 112mm 112mm 112mm 125mm 125mm 140mm 140mm 160mm 210mm 235mm 260mm 311mm 337mm 362mm 413mm 438mm Width Size Order No. Accuracy 4mm 4mm 4mm 4mm 4mm 5mm 5mm 5mm 7mm 7mm 7mm 7mm 7mm 7mm 7mm 7mm 7mm 7mm 7mm 7mm 7mm 10mm 10mm 10mm 10mm 10mm 10mm 10mm 15mm 15mm 15mm 15mm 15mm 20mm 20mm 20mm 20mm 25mm 25mm 25mm 25mm 25mm 38.1mm 38.1mm 38.1mm 38.1mm 38.1mm 38.1mm 38.1mm 38.1mm .1" .16" .24" .275" .35" .425" .50" .60" .65" .70" .80" 1.0" 1.2" 1.4" 1.6" 1.8" 2.0" 2.4" 2.5" 2.8" 3.0" 3.2" 3.5" 3.6" 4.0" 5.0" 6.0" 7.0" 8.0" 9.0" 10.0" 11.0" 12.0" 177-209 177-206 177-207 177-281 177-179 177-283 177-180 177-181 177-182 177-183 177-287 177-184 177-289 177-185 177-291 177-186 177-187 177-293 177-315 177-188 177-317 177-295 177-319 177-189 177-297 177-299 177-301 177-303 177-305 177-307 177-309 177-311 177-313 C-30 177-147 177-300 Inch ±.00004" ±.00004" ±.00004" ±.00004" ±.00004" ±.00004" ±.00004" ±.00004" ±.00004" ±.00004" ±.00004" ±.00004" ±.00004" ±.00004" ±.00004" ±.00004" ±.00004" ±.00004" ±.00006" ±.00006" ±.00006" ±.00006" ±.00006" ±.00006" ±.00008" ±.00008" ±.00008" ±.00010" ±.00010" ±.00010" ±.00012" ±.00012" ±.00012" Outside Diameter .98” .98” .98” .98” 1.26” 1.26” 1.26” 1.5” 1.77” 1.77” 1.77” 2.09” 2.8” 2.8” 2.8” 3.5” 3.5” 4.41” 4.41” 4.41” 4.92” 4.92” 5.51” 5.51” 6.3” 8.27” 9.25” 10.24” 12.24” 13.27” 14.25” 16.26” 17.24” 177-146 177-139 177-205 Width .28” .28” .28” .28” .39” .39” .39” .39” .39” .39” .39” .59” .59” .59” .59” .59” .79” .79” .79” .79” .98” .98” .98” .98” .98” 1.5” 1.5” 1.5” 1.5” 1.5” 1.5” 1.5” 1.5” Technical Data Tolerance between the nominal size and the actual diameter: ±0.01mm for ø1 - 45mm setting rings ±0.02mm for ø50 - 300mm setting rings ±.0004" for .1" - 1.8" DIA. setting rings ±.0008" for 2" - 12" DIA. setting rings Cylindricity: 1.0µm for ø1 - 60mm setting rings 1.5µm for ø62 - 90mm setting rings 2.0µm for ø100 - 150mm setting rings 2.5µm for ø175 - 225mm setting rings 3.0µm for ø250 - 300mm setting rings .00004" for .1" - 2.4" DIA. setting rings .00006" for 2.5" - 3.6" DIA. setting rings .00008" for 4" - 6" DIA. setting rings .00010" for 7" - 9" DIA. setting rings .00012" for 10" - 12" DIA. setting rings Ceramic Setting Ring SERIES 177 — Accessories for Inside Micrometers, Holtest and Dial Bore Gages FEATURES •No more anti-corrosion treatment is required when handling Ceramic Setting Rings normally, resulting in simple maintenance and storage. 177-424 Technical Data Tolerance between the nominal size and the actual diameter: ±0.01mm for ø1 - 45mm setting rings ±.0004" for .1" - 1.8" DIA. setting rings Cylindricity: 1.0µm for ø1 - 45mm setting rings .00004" for .1" - 1.8" DIA. setting rings 177-429 177-432 Ceramic Setting Rings Inch Metric Size 6mm 8mm 10mm 12mm 16mm 20mm 25mm 30mm 35mm 40mm 45mm Order No. 177-420 177-423 177-424 177-425 177-427 177-429 177-430 177-431 177-432 177-433 177-434 Accuracy ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm ±1.5µm Size .275" .35" .425" .5" .65" .8" 1" 1.2" 1.4" 1.6" 1.8" Order No. 177-522 177-523 177-524 177-525 177-527 177-529 177-530 177-531 177-532 177-533 177-534 Accuracy ±.00006" ±.00006" ±.00006" ±.00006" ±.00006" ±.00006" ±.00006" ±.00006" ±.00006" ±.00006" ±.00006" Bore Gage Zero Checker SERIES 515 The Bore Gage Zero Checker allows easy zero adjustment of dial bore gages with ranges of 18mm (.7") through 400mm (16") using gage blocks. SPECIFICATIONS Order No. 515-590 Applicable range 18 -400mm (.7" - 16") 515-590 C-31 RM-120 Ring Master Ring Gage Measuring Machine FEATURES •The laser holoscale incorporated in the RM-120 eliminates the need for a reference gage block set and reference ring gages. •Probe change is not required for the entire measuring range. •Enhanced repeatability and lower measuring force achieved with the air bearing on the probe carriage guide. SPECIFICATIONS Model No. Order No. Range Resolution (Counter) Analog meter Accuracy (±2s) Measuring unit Measuring force Work piece size Air requirement Air consumption Dimension (W x D x H) Mass RM-120 with analog meter 565-204A ID: .236 to 4.75” / 6 to 120mm .00000001” / 0.0001mm 200μm / .007874”, 20μm / .0007874” ±(0.3 + 5D/1000)μm D: Ring gage size diameter (mm) Laser Holoscale Approx. 0.2N OD: .7874 - 7.874” / 20 - 200mm Thickness: Up to 1.574” / 40mm 400KPa (58psi) Approx. 30 liter per minute (12.8CFM) 720mm x 494mm x 875mm 28.35” x 19.45” x 34.45” Approx. 260kg (573.2lbs) C-32 •Workpiece alignment is easy to perform with the specially designed measuring table which is capable of moving, tilting, elevating, and 90 degree rotating. •The model with an analog meter will further facilitate workpiece positioning. Optional Accessories 02ASE690: 02ASE700: 02ASE710: 02ASE720: 02ASC530: 02ASC560: 02ASC580: 02ASC540: 02ASE480: Master gage .250” with factory Inspection Certificate Master gage .500” with factory Inspection Certificate Master gage 3” with factory Inspection Certificate Master gage 4.750” with factory Inspection Certificate Master gage 6mm with factory Inspection Certificate Master gage 12.5mm with factory Inspection Certificate Master gage 75mm with factory Inspection Certificate Master gage 120mm with factory Inspection Certificate Vibration stand
Similar documents
Bore Gages
*The compatible models are the Standard Bore Gage (refer to page C-20) and Micrometer Head Bore Gage (refer to page C-22). *Accuracy may be affected by unintended deflections, etc., when using an e...
More informationBore Gages
125mm Extension rod for 18-35mm (.7"-1.4") models 125mm Extension rod for 35-160mm (1.4"-6.5") models 125mm Extension rod for 160-400mm (6.5"-16") models 250mm Extension rod for 18-35mm (.7"-1.4") ...
More informationMITUTOYO - INSIDE MEASURING
• Accuracy: .00016"/4µm (Range: .037–.4"/0.95–10mm) .00024"/6µm (Range: .4–.7"/10–18mm) • Optional stand (215-120) for Bore Gages Series 526 is available for efficient measurement of multiple
More informationBore Gage - Mitutoyo
18-35mm/.7”-1.4” 35-60mm/1.4”-2.5” 50-150mm/2”-6” 100-160mm/4”-6.5” 60-100mm/2.4”-4” 100-160mm/4.5”-6” 160-250mm/6.5”-10” 250-400mm/10”-16” 150-250mm/6”-10” 250-400mm/10”-16” 400-600mm/16”-24” 600-...
More information