2001-2005 Ducati Monster S4/R

2001-2005 Ducati Monster S4/R
I n s ta l l a t i o n I n s t r u c t i o n s
Parts List
1
Power Commander
1
CD-ROM
1
Button Adjustment Display
USB Cable
1
Installation Guide
1
Power Adapter
2
Power Commander Decals
2
Dynojet Decals
2
Velcro
®
1
Strip
Alcohol Swab
Faceplate Buttons
Expansion Port
USB Port
The ignition MUST be turned
OFF before installation!
You can also download the Power
Commander software and latest maps
from our web site at:
www.powercommander.com
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
Dynojet Research 2191 Mendenhall Drive North Las Vegas, NV 89031 (800) 992-4993 www.powercommander.com
i710-411
www.powercommander.com
2001-2005 Ducati S4 - PCIII USB - 1
These instructions can be used on either the S4 or S4R.
Fig. A
removed on the S4R.
Follow steps 14-20 for the S4R
The air box does NOT need to be
1
Remove the seat.
2
Prop the fuel tank in the upright posi-
3
Remove the airbox lid by disconnect-
Hooks
tion.
ing the two hooks on either side of the
airbox (Fig A).
either
Unscrew the bolts on
side of the rear of the
airbox or just lift up to remove the air
box.
4
Disconnect the two hoses going to the
5
Remove the velocity stacks by turning
airbox.
them counter-clockwise and lifting up
(Fig B).
Fig. B
Loosen these bolts
6
Remove the bolt on the underside of
7
The airbox can now be moved out of
the airbox (Fig. C).
the way.
To totally remove the airbox
disconnect the wire connectors from
Fig. C
the front of the airbox.
Remove this bolt
i710-411
www.powercommander.com
2001-2005 Ducati S4 - PCIII USB - 2
8
Unplug the stock connectors from the
injectors (Fig D).
Release the spring
clips to remove each connector.
Unplug these connectors
Fig. D
**Do not discard spring clip.
**Do not mix up the stock front and
rear connectors.
9
Plug the connectors from the PCIII inline of the stock connectors (Fig E).
The ORANGE colored wires from the
PCIII go to the front cylinder and the
YELLOW colored wires go to the rear
cylinder.
PCIII connectors
Reinstall spring clips.
Fig. E
Align the PCIII connector to the stock
wiring harness as shown below.
The
square edges of the PCIII connector
align with the spring clip side of the
stock wiring harness
Stock
PCIII
Stock connector
Spring clip
square edges
Stock connector
Unplug this connector
Fig. F
10
the underside of the throttle bodies
(Fig F).
Remove the
connector
by squeezing the spring clip.
11
i710-411
Locate the thottle position sensor on
www.powercommander.com
Plug the leads from the PCIII in-line
of this connection.
2001-2005 Ducati S4 - PCIII USB - 3
12
Install the PCIII on top of the battery
(Fig.G).
Make sure to clean both sur-
faces with the alcohol swab before
attaching.
Fig. G
13
Attach the ground lead from the PCIII
to the negative side of the battery.
Ground wire
Fig. H
Another view (Fig.H).
Follow the following instructions
for the S4R model only.
14
Unplug these connectors
Disconnect the stock wiring harness
from the throttle bodies (Fig. J).
**Do not mix up the stock front and
Fig. J
rear connectors.
i710-411
www.powercommander.com
2001-2005 Ducati S4 - PCIII USB - 4
15
Connect the YELLOW colored wires
from the PCIII to rear injector (Fig.
K).
PCIII connectors
Fig.K
Stock connectors
View from left side of bike
16
Connect the ORANGE colored wires
from the PCIII to front injector (Fig.
L).
Fig.L
PCIII connectors
Stock connectors
View from left side of bike
Unplug this connector
17
Locate the thottle position sensor on
the left hand, underside of the throttle
bodies (Fig M).
squeezing the spring clip.
Fig.M
tor by
Remove the connec-
i710-411
www.powercommander.com
2001-2005 Ducati S4 - PCIII USB - 5
18
PCIII connectors
Plug the connectors from the PCIII inline of the TPS and stock wiring har-
Fig.N
ness (Fig. N).
Stock connector
Ground wire from PCIII
19
Install the PCIII on top of the battery
20
Attach the ground wire from the PCIII
as shown in Fig. P
to the negative side of the battery
Fig.P
(Fig. P).
i710-411
www.powercommander.com
2001-2005 Ducati S4 - PCIII USB - 6