wall-mounted boilers, water heaters and pool heaters

Transcription

MADE IN ITALY
THE EXPERT of stainless
steel condensing
heating systems
ECO FRIEN
D LY
wall-mounted boilers,
water heaters and pool heaters
floor standing boilers,
water heaters and pool heaters
AISI 316Ti (Titanium) stainless steel heat exchangers
wall-mounted
up to 90,000 Btu/hr
wall-mounted
up to 200,000 Btu/hr
floor standing
399,000 Btu/hr
THE NEW GENERATION OF HIGH EFFIC
This water heating system is a stainless steel water
tubes condensing appliance, with low pollution, fully
modulating premixed burner. It is available in different
powers from 50,000 Btu/hr to 1,000,000 Btu/hr and in
wall-mounted or floor standing version.
The high efficiency heat exchanger allows the creation
of compact and light appliances with the possibility of
installing them in very small mechanical rooms.
Boiler versions can be connected to any type of heating
installation such as radiators, radiant panels, fan-coils,
etc..; water heater versions can be connected to any
D.H.W. production system and pool heaters can be
connected to any pool heating system.
All our appliances are equipped with premixed burners,
built in Fecralloy fibre, for a high efficiency combustion
and low polluting emissions (CO<15 ppm and NOx<15
floor standing
1,000,000 Btu/hr
floor standing
750,000 Btu/hr
floor standing
500,000 Btu/hr
IENCY CONDENSING HEATING SYSTEMS
ppm), together with the special air/gas mixer
Cosmomix and the pneumatic gas valve, at negative
pressure, allows appliances to reach turndown ratio up
to 20:1, adapting it to all load variations requested by
the system during different seasons and maintaining a
high combustion and efficiency.
Appliances are versatile respect to PVC, CPVC, stainless
steel and polypropylene venting systems and thanks to
the high head fan they can discharge up to 120 ft long.
They can also be connected to the combustion air duct
to have sealed system respect to the ambient.
Appliances are also equipped with: condensate siphon,
flue gas pressure switch, water flowmeter and water
pressure sensor.
PATENTED R.V.C. AISI 316Ti (TITANIUM)
Exceptional performance: the new patented R.V.C.
(Radial Variable Circulation) heat exchanger.
The core of all appliances is the new generation of heat
exchangers type R.V.C..
It is composed by 3 series of stainless steel round tubes.
In particular, the tube closest to the burner is built in
AISI 316Ti (TITANIUM) stainless steel.
These tubes are assembled and hydraulically connected
without welding, maintaining unaltered the chemical
and physical characteristics of the stainless steel, with
maximum warranty against corrosion.
Exceptional efficiency up to 98%.
Heat exchanger with low pressure drops and a high
resistance to the working pressure, up to 160 PSI (11 bar).
The external case is realized with an innovative
composite material PPX 830, which gives it exceptional
robustness, lightness and durability in time.
Approvals:
Premix burner advantages:
Fecralloy fibre
High efficiency combustion
Low polluting emissions
(CO<15 ppm and NOx<15 ppm)
Cosmomix advantages:
Turndown ratio up to 5:1 per heat
exchanger
Negative Pressure gas valve
3” W.C. min. supply gas pressure
) STAINLESS STEEL HEAT EXCHANGER
A unique range of products (boilers, water heaters and pool
heaters) with a uniformity of functions and, consequently,
easy to instruct throughout the whole supply and service
chain. Spare parts (fan, gas valve, control board, display
board, spark generator, pressure sensor, flow sensor,
temperature sensors, ignition electrode, detection
electrode, Modbus board) are the same for all power range
from 199 kBtu/hr up to 1000 kBtu/hr for all, boiler, water
heater and pool heater series. The after sales service
can do maintenance on all appliances with a very limited
number of spare parts.
Display, control board and general features:
Very intuitive control system
Connection with external sensor for outdoor reset so as to increase rooms comfort and to maintain
boiler temperature as low as possible to achieve the maximum seasonal efficiency
Display back-lightening turns off after 5 minutes of inactivity
Auto diagnostic of all components and functions, visualization of errors and lockouts, temperature
sensors, ionisation current, fan rotation speed, room thermostat status
Possibility of maximum and minimum domestic and heating power setting
Forcing high or low fire to facilitate combustion analysis
Anti-blocking pump system
Indirect water heater management
0-10Vdc input for external thermo regulator
Integrated MODBUS communication board to communicate with home building automation devices
(model 199, 250 and 399 on demand)
PC connection for diagnostic
Can be connected in cascade up to 4 appliances
Exit for alarm connection
Low gas pressure operation up to 3” W.C.
Zero clearances to combustible material
Connectable to indirect water heater drived via NTC sensor (boiler only)
Connectable to storage water heater drived via NTC sensor (water heater only)
Ideal to be connected to a pressure controlled variable speed pump
Freeze protection system
System pump control, boiler pump control and DHW pump control
DHW prioritization
Integrated air filter (for models 399, 500, 750, 1000 only)
Integrated condensate neutralizer kit (for models 399, 500, 750, 1000 only): volume of 26.4 dm3 (7 gal),
content 25 kg (55 lb) of limestone
On/off switch
Readable on the control system: water flow sensor (you can see the real GPM are running inside each heat
exchanger), supply temperature sensor, flue temperature sensor and tank temperature sensor
Low water flow protection
Water pressure sensor (display shows continuously the pressure inside the water system)
Low water pressure protection
Flue blocked pressure switch
Adjustable leveling feet
Condensate trap
Back flue preventer (flapper)
Vent damper (flapper)
MYdens 90MP, 130MP
condensing wall-mounted combi boiler
Cosmogas with MYdens 90MP,
130MP reaches a new achievement
in the condensing boilers sector
for the residential field.
A new concept of boilers able to
satisfy the new household needs,
that feature tinier spaces, energy
saving requests, comfort, ease of
use, reliability and a light impact on
the environment.
Only 12” (305mm) depth contain the
power of MYdens 90MP, 130MP, in
a sophisticated and elegant design
suitable for installation in any
residential space.
Its small size and lightness simplify
the installation. Attention has also
been paid to the accessibility of the
final user with simple and intuitive
commands, and ease of maintenance
with boiler frontal access.
Why choose MYdens:
Extra saving and efficiency
·Modern, innovative and attractive design
·Condensation technology
·Fully modulating
·Efficiency up to 98%
Comfort
·Silent
·Large DHW production
·Outdoor reset
·Easy installation and maintenance
·Reduced size and weight
·Very intuitive control system
Construction quality
·316Ti (Titanium) stainless steel R.V.C. heat exchanger
·Oversized stainless steel D.H.W. heat exchanger
·Turndown ratio up to 5:1
Ecology
·Reduced gas emissions in the atmosphere
CO<15 ppm and NOx<15 ppm
MYdens 90MP, 130MP
1 unit, 4 important features:
Heating for warm and comfortable spaces
D.H.W. production: large, adjustable and continuous
Saving with condensing technology
Ecology with combustion control technology
MYdens 90MP, 130MP
condensing wall-mounted combi boiler
MYdens is available with powers
50,000 Btu/hr, 90,000 Btu/hr.
Cosmogas, with MYdens 90MP,
130MP, started a conceptual
revolution that defines a new
pattern where energy saving and
respect for the environment were
brought to a new level. It is an
example the absence of weldings,
which reduces the use of primary
energy in the production process, in
line with the canons of eco-design
which provide the recuperation of
individual homogeneous materials.
12,6
”-3
20m
m
Wall-mounted boilers can be in a
“combi” version. For this, they install
a domestic heat exchanger with
big dimensions for a high D.H.W.
production. Immediate availability
of hot water: wellness and comfort.
D.H.W. is produced through an
oversized (L=12,6” - 320mm) stainless
steel plate heat exchanger, which
allows high availability of D.H.W.
and fast service. Bath and showers
thanks to the hot water produced
by MYdens give wellness, relax and
energy when workdays are long and
stressful.
D.H.W. PRODUCTION ∆T 75°F
3.51
gpm
2.43
gpm
90MP
130MP
MYdens 90MP, 130MP
DIMENSIONS AND CONNECTIONS
1
2
4
5
6
7
8
9
-
HEATING SUPPLY
D.H.W. OUTLET
GAS INLET
COLD WATER INLET
HEATING RETURN
FLUE GASES DISCHARGE/AIR INTAKE
SUPPORT CONNECTIONS
CONDENSATE DISCHARGE Ø3/4”
OPERATING SCHEME
1 - Air inlet
2 - Flue exhaust
3 - Automatic air vent
4 - Sealing chamber
5 - Expansion tank
6 - High limit supply temp. SWITCH
7 - Supply temperature sensor
8 - Purging cock
9 - Flue gas temperature sensor
10 - High limit flue gas temp. SWITCH
11 - Air inlet water tank
12 - Premix burner
13 - Ignition electrodes
14 -ignitor
15 - Return temperature sensor
16 - Modulating PWM fan
17 - Back flue preventer
18 - Plate heat exchanger
19 - Water pressure sensor
20 - Gas valve
21 - Circulator pump
22 - Detection electrode
24 - R.V.C. Stainless steel heat exchanger
25 - Heating supply
26 - Heating RETURN
27 - Gas supply
30 - Condensing drain
31 - Condensate Siphon
32 - HOT water sensor
34 - By-pass heating supply valve
35 - Three-way valve
37 - SAFETY RELIEF VALVE
38 - Domestic water strainer
40 - Return purging cock
41 - COLD WATER inlet
42 - D.H.W. OUTlet
43 -feeding cock
47 - D.H.W. Flow meter
MYdens 50M, 90M, 130M 199M
condensing wall-mounted boiler
With MYdens 50M to 199M Cosmogas
reaches a new achievement in the
condensing boilers sector for the
independent residential sector.
A new concept of boilers able to
satisfy the new household needs,
the environment.
Only 19” (484mm) depth contain the
power of this series of appliances, in
a sophisticated and elegant design
residential space.
The heart of these appliances lies in
the R.V.C. heat exchanger.
Therefore, the boiler is able to
adapt to all changing load situations
required by the system during
the heating cycle, keeping high
performances and high combustion
efficiency.
Cosmogas with MYdens started a
conceptual revolution that defines
a new pattern where energy saving
and the respect for the environment
were brought to a new level.
Why choose MYdens M:
·Fully modulating
Comfort
·Silent
·Outdoor reset
Ecology
MYdens 50M, 90M, 130M 199M
DIMENSIONS AND CONNECTIONS MYDENS 50M - 90M - 130M
9.52"
(242mm)
DIMENSIONS AND CONNECTIONS MYDENS 199M
7.95"
(202mm)
1 - HEATING SUPPLY
2 - GAS INLET
3 - HEATING RETURN
4 - FLUE GASES DISCHARGE/
AIR INTAKE
5 - SUPPORT CONNECTIONS
1 - HEATING SUPPLY
2 - GAS INLET
3 - HEATING RETURN
4 - FLUE GASES DISCHARGE/
AIR INTAKE
5 - SUPPORT CONNECTIONS
OPERATING SCHEME
1 - Air inlet
2 - Flue exhaust
4 - Sealing chamber
12 - Premix burner
14 -ignitor
20 - Gas valve
21 - Circulator pumP
25 - Heating supply
26 - Heating RETURN
27 - Gas INLET
47 - Flow meter
MYdens 199T, 250T, 399T, 500T
condensing floor standing boiler
MYdens 199T, 250T, 399T and
500T are condensing boilers that
can be installed directly on the floor
thanks to their power, reduced size
and lightness, freeing space inside
mechanical rooms. MYdens 199T
and 250T are equipped with one
R.V.C. heat exchanger made of AISI
316Ti (titanium) stainless steel.
MYdens 399T and 500T are equipped
with 2 R.V.C. heat exchangers made
of AISI 316Ti (titanium) stainless
steel that work in cascade mode
with unit power at 199,500 btu/hr
(MYdens 399T) and 250,000 btu/hr
(MYdens 500T).
The turndown ratio is up to 10:1.
Every heat exchanger is equipped
with all control and safety devices.
The boiler, being a multi-heat
exchanger, has more reliability in
case of malfunction occurring to
one module, while the others work
without any problem. Furthermore,
multiple exchangers have power
control boards that communicate
among them and handle the power
output of every module in a uniform
and coordinated way in order to
guarantee the maximum efficiency,
turnover and a uniform wearing out.
MYdens 399T - 500T
Why choose MYdens T:
·Fully modulating
Comfort
·Silent
·Outdoor reset
Ecology
MYdens 199T - 250T
MYdens 199T, 250T, 399T, 500T
FRONT VIEW
SIDE VIEW
REAR VIEW
1 - HEATING SUPPLY
2 - HEATING RETURN
3 - AIR INLET
4 - FLUE GASES DISCHARGE
5 - GAS INLET
6 - CONDENSING DRAIN
OPERATING SCHEME
1 - Air inlet
2 - Flue exhaust
4 - Sealing chamber
8 - WATER PRESSURE SENSOR
12 - Premix burner
14 -ignitor
20 - Gas valve
25 - Heating supply
26 - Heating RETURN
27 - Gas INLET
28 - Blocked flue pressure switch
29 - Condensing blocked drain switch
32 - 2nd R.V.C. (MODELS 399T - 500T)
33 - System temperature sensor
36 - Condensate neutralizer
47 - Flow meter
48 - Check valve
50 - DRAIN VALVE
MYdens 750T, 1000T
MYdens 750T and MYdens 1000T
are condensing boilers that can
be installed directly on the floor
mechanical rooms. MYdens 750T and
MYdens 1000T are equipped with 3
or 4 R.V.C. heat exchangers made of
AISI 316Ti (titanium) stainless steel
that work in cascade mode with unit
power at 250,000 Btu/hr.
The boiler, being a multi-heat
exchanger, has more reliability in
case of malfunction occurring to
MYdens 1000T
Why choose MYdens 750T, 1000T:
·Fully modulating
Comfort
·Silent
·Outdoor reset
Ecology
MYdens 750T
MYdens 750T, 1000T
FRONT VIEW
OPERATING SCHEME
REAR VIEW
SIDE VIEW
1 - HEATING SUPPLY
2 - HEATING RETURN
3 - AIR INLET
5 - GAS INLET
1 - Air inlet
2 - Flue exhaust
4 - Sealing chamber
6 - High limit supply temp.
switch
7 - Supply temp. sensor
9 - Flue gas temp. sensor
10 - High limit flue gas temp.
switch
12 - Premix burner
14 -ignitor
15 - Return temp. sensor
20 - Gas valve
23 - Supply and return
manifolds
24 - R.V.C. Stainless steel heat
exchanger
25 - Heating supply
26 - Heating RETURN
27 - Gas INLET
28 - Blocked flue pressure
switch
29 - Condensing blocked drain
switch
32 - 4th R.V.C. (MODELS 1000T)
33 - System temp. sensor
47 - Flow meter
48 - Check valve
50 - DRAIN VALVE
MYdens Cascade Sequence
MYdens 1000T can be used and
connected in cascade to achieve a
maximum power of 4,000,000 Btu/hr.
Thanks to the cascade connection
up to 4 MYdens 1000T the turndown
ratio is very high 80:1 and you will
get exceptional results in systems
that need high powers to start and
small powers to operate.
It is also recommended in all the
installations where it is necessary to
ensure a continuity of operation.
Why choose MYdens:
·Fully modulating
Comfort
·Silent
·Outdoor reset
Ecology
An example of connection
MYdens Cascade Sequence
CONTROLLER
Cascade sequences up to 4-appliances using
2-wire daisy-chain connection.
One boiler functions as the master and the
other as slaves, and modulates to capacity.
Appliances can be installed in battery with
a minimum distance of 4”. For this purpose,
the whole design has been conceived to gain
access from the front and from the back for
each type of maintenance.
POSSIBLE ARRANGEMENTS
51.25" (1302mm)
78.89" (2004mm)
71.45"
(1815mm)
71.45"
(1815mm)
23.62"
23.62"
4.01"
(600mm) (102mm) (600mm)
from 50 to 2,000 kBtu/hr
71.45"
(1815mm)
106.54" (2706mm)
AGUAdens 90M, 130M, 199M
condensing wall-mounted water heater
With AGUAdens Cosmogas reaches a
new achievement in the condensing
water heaters sector for the
independent residential sector.
A new concept of water heaters able
to satisfy the new household needs,
the environment.
Only 12” (305mm) depth contain
the power of AGUAdens, in a
sophisticated and elegant design
residential space.
Cosmogas with AGUAdens, started
a conceptual revolution that defines
a new pattern where energy saving
and the respect for the environment
were brought to a new level.
Why choose AGUAdens M:
·Fully modulating
Comfort
·Silent
·Instantaneous DHW production
Ecology
AGUAdens 90M, 130M, 199M
1
2
3
4
5
6
7
-
RECYCLING LOOP CONNECTION
DOMESTIC HOT WATER SUPPLY
GAS INLET
COLD WATER
FLUE GASES DISCHARGE/AIR INTAKE
SUPPORT CONNECTIONS
CONDENSING DRAIN Ø3/4”
A - 12” (305mm) (90M and 130M models)
19.05” (484mm) (199M models)
B - 4.72” (120mm) (199M models)
C - 4.92” (125mm) (90M and 130M models)
11.96” (304mm) (199M models)
OPERATING SCHEME
1 - WATER HEATER
2 - AIR INLET
3 - Flue exhaust
4 - High limit Flue GAS TEMP. SWITCH
5 - FLUE GAS TEMPERATURE SENSOR
6 - Sealing chamber
7 - WATER BAG CONVEIOR
8 - HOT WATER TEMPERATURE SENSOR
9 - High limit HOT WATER SWITCH
10 - Premix burner
12 - Modulating fan
13 -cold water temperature sensor
15 - AIR/GAS MIXING DEVICE
16 - Gas valve
18 - BALL VALVE
19 - RECIRCULATION PUMP
20 - CHECK VALVE
21 - FLOW METER
22 - RECYCLING LOOP CONNECTION
23 - CAP
24 - HOT WATER TEMPERATURE SENSOR
25 - SHUT OFF GAS VALVE
26 - GAS SUPPLY
27 - COLD WATER INLET
AGUAdens 199T, 250T, 399T, 500T
condensing floor standing water heater
AGUAdens 199T, 250T, 399T and
500T are condensing water heaters
that can be installed directly on the
floor thanks to their power, reduced
size and lightness, freeing space
inside mechanical rooms.
AGUAdens 199T and 250T are equipped
with one R.V.C. heat exchanger made
of AISI 316Ti (titanium) stainless steel.
AGUAdens 399T and 500T are equipped
with 2 R.V.C. heat exchangers made of
AISI 316Ti (titanium) stainless steel that
work in cascade mode with unit power
at 199,500 btu/hr (AGUAdens 399T)
and 250,000 btu/hr (AGUAdens 500T).
The water heater, being a multiheat exchanger, has more reliability
in case of malfunction occurring to
AGUAdens 399T - 500T
Why choose AGUAdens T:
AGUADENS CONNECTED TO WATER STORAGE TANK
1
2
3
4
1 - AGUADENS
2 - WATER STORAGE TANK
·Fully modulating
Comfort
·Silent
Ecology
3 - DOMESTIC HOT WATER SUPPLY
AGUAdens 199T, 250T, 399T, 500T
FRONT VIEW
SIDE VIEW
REAR VIEW
3 - AIR INLET
5 - GAS INLET
OPERATING SCHEME
1 - Air inlet
2 - Flue exhaust
4 - Sealing chamber
6 - High limit HOT WATER temp. switch
7 - SUPPLY temperature sensor
10 - High limit flue gas temp. FUSE
12 - Premix burner
14 -ignitor
20 - Gas valve
25 - Hot water outlet
26 - Cold water inlet
27 - Gas INLET
28 - Blocked flue pressure switch
29 - Condensing blocked drain switch
32 - 2nd R.V.C. (MODELS 399T - 500T)
33 - System temperature sensor
47 - WATER Flow meter
48 - Check valve
49 -cold water temperature sensor
50 - DRAIN VALVE
AGUAdens 750T, 1000T
condensing floor standing water heater
AGUAdens 750T and AGUAdens 1000T
are condensing water heaters that
can be installed directly on the floor
mechanical rooms. AGUAdens 750T
and AGUAdens 1000T are equipped
with 3 or 4 R.V.C. heat exchangers
made of AISI 316Ti (titanium) stainless
steel that work in cascade mode with
unit power at 250,000 Btu/hr.
The water heater, being a multiheat exchanger, has more reliability
in case of malfunction occurring to
AGUAdens 1000T
Why choose AGUAdens T:
AGUADENS CONNECTED TO WATER STORAGE TANK
1
2
3
·Fully modulating
Comfort
·Silent
Ecology
4
1 - AGUADENS
2 - WATER STORAGE TANK
AGUAdens 750T, 1000T
FRONT VIEW
OPERATING SCHEME
REAR VIEW
SIDE VIEW
3 - AIR INLET
5 - GAS INLET
1 - Air inlet
2 - Flue exhaust
4 - Sealing chamber
6 - High limit hot water
temp. SWITCH
7 - Supply temp. sensor
9 - Flue gas temp. sensor
10 - High limit flue gas temp.
FUSE
12 - Premix burner
14 -ignitor
20 - Gas valve
23 - COLD AND HOT water
manifolds
24 - R.V.C. Stainless steel heat
exchanger
25 - Hot water outlet
26 - Cold water inlet
27 - Gas INLET
28 - Blocked flue pressure
switch
29 - Condensing blocked drain
switch
32 - 4th R.V.C. (MODELS 1000T)
33 - System temp. sensor
47 - Flow meter
48 - Check valve
49 - COLD WATER temp. sensor
50 - DRAIN VALVE
BOILERS MYdens
TECHNICAL DATA
Category of discharge chimney
Maximum heat input
Minimum heat input
Turndown ratio
Number of burners
Efficiency at maximum heat input (160°F/140°F)
Efficiency at minimum heat input (122°F/86°F)
AFUE rate
Gas flow rate (Natural Gas)
Gas flow rate (LP Gas)
Min/Max gas pressure (Natural and LP Gas)
Min/Max heating temperature
Min/Max heating pressure
Minimum water flow
Supply Voltage/Frequence
Absorbed electric power
Air intake/Flue gas pipes diameter
Maximum length venting system
Balanced CO (Carbon monoxide) with natural gas
Balanced NOx contents (0% O2 with natural gas)
Weight (empty of water)
Instantaneous DHW delivery (75°F rise)
Gas connection
Supply and return connections
DHW connections (cold water - hot water)
Btu/hr
Btu/hr
%
%
%
ft3/hr
ft3/hr
In. W.C.
°F
PSI
GPM
Vac/Hz
W
inch
ft
ppm
ppm
lb
GPM
inch
inch
inch
90MP
IV
90,000
22,500
4:1
1
94
98
94
90
36
3/13
68/189
8/160
4
120/60
90
3
120
<100
<30
100
2.43
3/4”
3/4”
1/2” - 1/2”
130MP
IV
130,000
32,500
4:1
1
94
98
94
130
52
3/13
68/189
8/160
4
120/60
90
3
120
<150
<30
100
3.51
3/4”
1”
1/2” - 1/2”
50M
IV
50,000
12,500
4:1
1
94
98
94
50
20
3/13
68/189
8/160
4
120/60
70
3
120
<90
<30
90
N/A
3/4”
3/4”
N/A
90M
IV
90,000
22,500
4:1
1
94
98
94
90
36
3/13
68/189
8/160
4
120/60
90
3
120
<100
<30
100
N/A
3/4”
3/4”
1/2” - 1/2”
199M
IV
199,500
50,000
4:1
1
94
98
227
199.5
80
3/13
104/140
8/160
1
120/60
110
3
120
<150
<30
163
5.37
3/4”
1”
199T
IV
199,500
50,000
4:1
1
94
98
227
199.5
80
3/13
104/140
8/160
4
120/60
110
3
120
<150
<30
163
N/A
1”
1” 1/2
WATER HEATERS AGUAdens
TECHNICAL DATA
Category of discharge chimney
Maximum heat input
Minimum heat input
Turndown ratio
Number of burners
Efficiency at maximum heat input (160°F/140°F)
Efficiency at minimum heat input (122°F/86°F)
Recovery rating
Gas flow rate (Natural Gas)
Gas flow rate (LP Gas)
Min/Max gas pressure (Natural and LP Gas)
Min/Max water temperature
Min/Max water pressure
Minimum water flow
Supply Voltage/Frequence
Absorbed electric power
Air intake/Flue gas pipes diameter
Maximum length venting system
Balanced CO (Carbon monoxide) with natural gas
Balanced NOx contents (0% O2 with natural gas)
Weight (empty of water)
Instantaneous DHW delivery (75°F rise)
Gas connection
DHW connections (cold water - hot water)
Btu/hr
Btu/hr
%
%
Gal/hr
ft3/hr
ft3/hr
In. W.C.
°F
PSI
GPM
Vac/Hz
W
inch
ft
ppm
ppm
lb
GPM
inch
inch
90M
IV
90,000
22,500
4:1
1
94
98
103
90
36
3/13
104/140
8/160
0.5
120/60
90
3
120
<100
<30
100
2.43
3/4”
1/2” - 1/2”
130M
IV
130,000
32,500
4:1
1
94
98
148
130
52
3/13
104/140
8/160
0.5
120/60
90
3
120
<150
<30
110
3.51
3/4”
1/2” - 1/2”
MYdens
130M
IV
130,000
32,500
4:1
1
94
98
94
130
52
3/13
68/189
8/160
4
120/60
90
3
120
<150
<30
100
N/A
3/4”
1”
1/2” - 1/2”
199M
IV
199,500
50,000
4:1
1
94
98
94
199.5
80
3/13
68/189
8/160
4
120/60
110
3
120
<150
<30
110
N/A
3/4”
1” 1/2
N/A
199T
IV
199,500
50,000
4:1
1
94
98
94
199.5
80
3/13
68/189
8/160
4
120/60
110
3
120
<150
<30
171
N/A
1”
1” 1/2
N/A
250T
IV
250,000
50,000
5:1
1
94
98
94
250
100
3/13
68/189
8/160
4
120/60
150
3
120
<150
<30
176
N/A
1”
1” 1/2
N/A
399T
IV
399,000
50,000
8:1
2
94
98
94
399
160
3/13
68/189
8/160
4
120/60
220
4
120
<150
<30
242
N/A
1”
1” 1/2
N/A
AGUAdens
250T
IV
250,000
50,000
5:1
1
94
98
285
250
100
3/13
104/140
8/160
4
120/60
150
3
120
<150
<30
167
N/A
1”
1” 1/2
399T
IV
399,000
50,000
8:1
2
94
98
455
399
160
3/13
104/140
8/160
4
120/60
220
4
120
<150
<30
233
N/A
1”
1” 1/2
500T
IV
500,000
50,000
10:1
2
94
98
570
500
200
3/13
104/140
8/160
4
120/60
300
4
120
<150
<30
242
N/A
1”
1” 1/2
750T
IV
750,000
50,000
15:1
3
94
98
885
750
300
3/13
104/140
8/160
4
120/60
430
6
120
<150
<30
397
N/A
1” 1/2
1” 1/2
1000T
IV
999,000
50,000
20:1
4
94
98
1,138
999
400
3/13
104/140
8/160
4
120/60
591
6
120
<150
<30
485
N/A
1” 1/2
1” 1/2
500T
IV
500,000
50,000
10:1
2
94
98
94
500
200
3/13
68/189
8/160
4
120/60
300
4
120
<150
<30
253
N/A
1”
1” 1/2
N/A
750T
IV
750,000
50,000
15:1
3
94
98
94
750
300
3/13
68/189
8/160
4
120/60
430
6
120
<150
<30
462
N/A
1” 1/2
2” 1/2
N/A
1000T
IV
999,000
50,000
20:1
4
94
98
94
999
400
3/13
68/189
8/160
4
120/60
591
6
120
<150
<30
551
N/A
1” 1/2
2” 1/2
N/A
NOTES
NOTES
EU
USA
USA
AUTHORIZED DEALER
Canada
COSMOGAS srl • Via L. da Vinci, 16 • 47014 MELDOLA (FC) ITALY • Tel. +39 0543.49.83.70 • Fax +39 0543.49.83.92
www.cosmogas.com • [email protected]
62401287 - Ottobre 2013 - WITH THE AIM OF CONSTANTLY DEVELOPING AND IMPROVING IT’S PRODUCTS, COSMOGAS RESERVES THE RIGHT TO MODIFY, UPDATE AND IMPROVE, AT ANY TIME, THIS FOLDER.
Massimiliano Pieraccini
COSMOGAS International Certifications

wall-mounted boilers, water heaters and pool heaters

Transcription

Similar documents

CSG series Premix Gas CONDENSING wall-mounted

kik-step®

Two forces working with the weather…

The idea with modifying stock down pipes is to gut the pre

2005 Haulmark This Motorhome is amazing as the pictures will

Your enquiries are always welcome. STAINLESS OUTFITTERS 161

Mynute Green k - Beretta Boilers

iSCOUT PRS80

your seventh sense - L

TEA STAINED STAINLESS STEEL?