ICF-CD2000 - Electronica.ro
Transcription
ICF-CD2000/CD2000S SERVICE MANUAL US Model Canadian Model E Model Tourist Model Ver 1.0 1999. 10 ICF-CD2000 AEP Model UK Model ICF-CD2000S Photo: ICF-CD2000 (US model) Model Name Using Similar Mechanism D-E551 Optical Device Name CDM-2911EBA Optical Pick-Up Name DAX-11E SPECIFICATIONS ICF-CD2000 FM/AM CD CLOCK RADIO ICF-CD2000S FM/SW/MW CD CLOCK RADIO MICROFILM TABLE OF CONTENTS 1. SERVICING NOTES ................................................ 3 2. GENERAL ................................................................... 5 3. DISASSEMBLY ......................................................... 8 4. SERVICE MODE ...................................................... 11 5. TEST MODE .............................................................. 12 6. ELECTRICAL ADJUSTMENTS ......................... 15 7. DIAGRAMS 7-1. 7-2. 7-3. 7-4. 7-5. 7-6. 7-7. IC Pin Function Description ........................................... Block Diagram – CD Section – ..................................... Block Diagram – Main Section – ................................... Printed Wiring Boards – MAIN/JACK Boards – .......... Schematic Diagram – MAIN/JACK Boards – .............. Printed Wiring Boards – LCD/KEY Boards – .............. Schematic Diagram – LCD/KEY Boards – ................... 8. EXPLODED VIEWS ................................................ 53 9. ELECTRICAL PARTS LIST ............................... 57 21 23 27 31 35 40 45 CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. Flexible Circuit Board Repairing • Keep the temperature of the soldering iron around 270 ˚C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. Notes on chip component replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. HOW TO CHANGED THE CERAMIC FILTERS This model is used two ceramic filters of CF1 and CF3. You must use same type of color marked ceramic filters in order to meet same specifications. Therefore, the ceramic filter must be changed two pieces together since it’s supply two pieces in one package as a spare parts. SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. –2– SECTION 1 SERVICING NOTES NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. Before Replacing the Optical Pick-Up Block Please be sure to check thoroughly the parameters as par the “Optical Pick-Up Block Checking Procedures” (Part No.: 9-960-02711) issued separately before replacing the optical pick-up block. Note and specifications required to check are given below. • FOK output: IC501 ts pin • S curve P-to-P value: 1.2 Vp-p IC501 wa pin When checking S curve P-to-P value, remove the lead wire to disc motor. • RF signal P-to-P value: 0.8 to 1.3 Vp-p • Traverse signal P-to-P value: 0.7 to 1.8 Vp-p • The repairing grating holder is impossible. Precautions for Checking Emission of Laser Diode Laser light of the equipment is focused by the object lens in the optical pick-up so that the light focuses on the reflection surface of the disc. Therefore, be sure to keep your eyes more then 30 cm apart from the object lens when you check the emission of laser diode. Laser Diode Checking Methods During normal operation of the equipment, emission of the laser diode is prohibited unless the upper panel is closed while turning ON the S423. (push switch type) However, in the service mode, the laser diode always emits light even if S423 is not turned on. The following two checking methods for the laser diode are operable. • Method-1 (In the service mode or normal operation): Emission of the laser diode is visually checked. 1. Open the upper lid. 2. Push the S423 as shown in Fig. 1. (Unnecessary in the service mode) 3. Press the [CD u] key. 4. Check the object lens for confirming normal emission of the laser diode. If not emitting, there is a trouble in the automatic power control circuit or the optical pick-up. During normal operation, the laser diode is turned ON about 2.5 seconds for focus searching. Fig. 1 Method to push the S423 –3– • Method-2 (In the service mode or normal operation): Check the value of current flowing in the laser diode. 1. Remove the upper panel. 2. Connect a digital voltmeter as show in Fig. 2. 3. Press the [CD u] key. 4. Calculate current value by the reading of the digital voltmeter. Reading of the digital voltmeter (V) ÷ 2.2 (Ω) = current value (A) (Example) Reading of the digital voltmeter of 0.082 V: 0.082 V÷2.2 Ω= 0.037 (A) = 37 mA Current value of the specified: 16 to 18 mA 5. Check that the current value is within the following range. +5 • Current value of the specified –11 mA (25 ˚C) Variation by temperature: 0.4 mA/˚C Current increases with temperature increased. Current decreases with temperature decreased. If the current is more than the range above, there is a trouble in the automatic power control circuit or the laser diode is in deterioration. If less than the range, a trouble exists in the automatic power control circuit or the optical pick-up. – MAIN Board (Conductor Side) – digital voltmeter (DC3 V range) TP (IOP 1) D501 A K L501 C510 C609 R552 R553 Q601 BCE + C608 C610 + R632 + C541 C619 C540 FB401 C554 R851 C555 R854 2E 2B 1C R565 C801 R568 2C 1B 1E R557 Q501 C505 R567 1E 1B 2C C553 2C1B 1E BCE Q503 2E2B 1C C519 R844 2E2B1C R558 R591 Q514 1 + C515 C552 K BCE 16 A A R524 C516 R478 C495 IC404 R549 D504 Q502 Q513 C504 C559 C506 R566 2C1B 1E R501 A C568 + C551 C494 R483 C419 R476 9 8 R477 99 + C561 C520 + K + C569 C493 C585 C595 + 13 C807 C806 C805 D512 BCE C565 C545 C564 R539 Q505 1C 2B 2E C803 R584 R576 Q507 R575 1-673-930- 11 (11) Fig. 2 Digital voltmeter connecting location –4– R850 C502 C542 C533 TP (TE) R525 TP (RF) L511 14 TP (VC) C543 + L515 C535 + C534 + C587 C586 L508 C536 R535 R631 TP (GND) TP (IOP 0) + – SECTION 2 GENERAL –5– This section is extracted from instruction manual. –6– –7– SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. Cabinet (lower) assy Cabinet (upper) Optical pick-up (CDM-2911EBA) Main board Cabinet (front) sub assy Set Note: Follow the disassembly procedure in the numerical order given. CABINET (LOWER) ASSY 5 cabinet (upper) assy 4 flat wire (CN301) 1 Open the battery case lid. 3 four claws 3 two claws 6 cabinet (lower) assy 2 five screws (2 × 8) 3 two claws 3 two claws –8– CABINET (UPPER) 1 screw (2 × 8) 2 two claws 2 four claws 1 screw (2 × 8) 3 cabinet (upper) 2 three claws CABINET (FRONT) SUB ASSY 6 cabinet (front) sub assy knob (open) 2 Slide the knob (open) in the direction of the arrow A, and open the cabinet front assy. 5 cover A cabinet (front) assy 4 Pull out two flat wires. 3 connector (CN701) 1 screw (2 × 8) –9– OPTICAL PICK-UP (CDM-2911EBA) 3 optical pick-up (CDM-2911EBA) 2 three connectors (CN601, 602, 603) 1 connector (CN501) MAIN BOARD 4 Remove two solders. 3 two screws (B1.7 × 5) 5 jack board 6 screw (2 × 8) 2 telescopic antenna 7 main board 1 screw (B3 × 6) – 10 – SECTION 4 SERVICE MODE Service Mode (Service program) The equipment is provided with a service program built in the microcomputer, like conventional models. Service program operation methods are described in the following. • Step 1 (Service mode setting methods) 1. Connect TP447 (CD TEST 2) to the TP444 (GND). 2. Turn ON the S423 (CD OPEN switch). 3. Insert external power supply. 4. Connect TP453 (RESET) to the TP444 (GND) to make open. (Reset) • Step 2 (Operation in the service mode) 1. Once the service mode is effected, the LCD displays 18 indications each of which is repeatedly displayed. 2. By pressing the > or . key, the optical pick-up is movable inwardly or outwardly. However, if this is activated, tracking servo and sled servo are turned OFF, so it can be turned ON by pressing the [BAND] key if required. 3. Without disk, focus searching is repeated continuously. 4. By pressing the [BAND] key, tracking servo, sled servo and CLV-A (servo in PLAY) are turned ON. Then playing begins. No muting is ON in the service mode. • Step 3 (Resetting of service mode) 1. Remove external power supply. 2. Disconnect TP447 (CD TEST 2) and TP444 (GND), and also TP453 (RESET) and TP444 (GND). – LCD Board (Component Side) – TP444 (GND) TP447 (CD TEST 2) TP453 (RESET) Fig. 3 Location of CD TEST terminal – 11 – SECTION 5 TEST MODE [Test Mode 1] • Step1 (Test mode 1 setting methods) 1. Connect TP445 (CD TEST 1) to the TP444 (GND). 2. Insert external power supply. [Test Mode 3] • Step1 (Test mode 3 setting methods) 1. Connect TP448 (CD TEST 3) to the TP449 (GND). 2. Insert external power supply. • Step2 (Operation in the test mode 1) 1. The CD auto adjustment is not performed, but LCD test mode is displayed. Also, ESP is placed in OFF state and it does not turn ON. 2. The sled is operating while the > or . key is pressed. At this time, the spindle and tracking servos turn OFF. 3. The focus search is performed until the focus becomes OK, if the [CD u ] key is pressed. At this time, the spindle and tracking servos turn OFF. Also, when the focus becomes OK, the optical pick-up moves to almost center of 12 cm disc. 4. The spindle and tracking servos turn ON when the [BAND] key is pressed. Also, the mute turns OFF if the data is correct. • Step2 (Operation in the test mode 3) 1. The same operation as in test mode 2 is performed. However, the LCD test mode is displayed same as in test mode 1. • Step3 (Resetting of test mode 1) 1. Remove external power supply. 2. Disconnect TP445 (CD TEST 1) and TP444 (GND). [Test Mode 2] • Step1 (Test mode 2 setting methods) 1. Connect TP447 (CD TEST 2) to the TP444 (GND). 2. Insert external power supply. • Step2 (Operation in the test mode 2) 1. The CD auto adjustment is performed. Also, the ESP can be turned ON or OFF. 2. The sled is operating while the > or . key is pressed. At this time, the spindle and tracking servos turn OFF. 3. The focus search is performed until the focus becomes OK, if the [CD u ] key is pressed. At this time, the spindle and tracking servos turn OFF. Also, when the focus becomes OK, the optical pick-up moves to almost center of 12 cm disc. 4. The spindle and tracking servos turn ON when the [BAND] key is pressed. Also, the mute turns OFF if the data is correct. 5. The pickup jumps by one track if > or . key is pressed when the spindle and tracking servos turn ON, or it jumps continuously if the key is kept pressed. Also, if the [PRESET] key is pressed, the following operation is performed. [PRESET 1] 1 track jump [PRESET 2] 4 track jump [PRESET 3] 16 track jump [PRESET 4] 32 track jump [PRESET 5] 256 track check 6. The pickup jumps to the second music and the test mode is released, if [CD u] key is pressed when the spindle and tracking servos turn ON. – 12 – [ALARM TIME]: [LCD Display Check Mode] • Step1 (LCD display check mode setting metyods) 1. Connect TP446 (TUNER TEST) to the TP444 (GND). 2. Insert external power supply. CD E • Step2 (Operation in the LCD display check mode) 1. All segments of LCD light up if the LCD display check mode is activated. 2. If each key is pressed, the LCD display is as shown below. At the same time, for some keys, the following operation is performed. CD N AM Buzzer sound OFF [SNOOZE]: [CLOCK]: AM FM 2 WORLD MW BUZZER LED ON TIMEDIF [ALARM TRACK/STATION]: [ESP]: SLEEP AM ESP WAKEUP INTROSCAN REPEAT ALL LED OFF Beep sound ON [>]: [CD PLAY MODE]: SHUFFL REPEAT1 [.]: Beep sound OFF [WORLD/LOCAL]: LOCAL PM [BAND]: [D.S.T SUMMER T.]: FM1 MHz kHz PRESET [PRESET 1]: [ALARM MODE]: RADIO SW [PRESET 2]: PM Buzzer sound ON – 13 – [PRESET 3]: [PRESET 4]: [PRESET 5]: [x OFF, ALARM RESET]: All lit • Step3 (Resetting of LCD display check mode) 1. Remove external power supply. 2. Disconnect TP446 (TUNER TEST) and TP444 (GND). Connecting Location: – LCD Board (Conductor Side) – TP445 (CD TEST 1) TP448 (CD TEST 3) TP449 (GND) TP444 (GND) TP446 (TUNER TEST) TP447 (CD TEST 2) – 14 – SECTION 6 ELECTRICAL ADJUSTMENTS TUNER SECTION AM (MW) FREQUENCY COVERAGE ADJUSTMENT 0 dB=1 µV Adjustment Part Frequency Display Reading on Digital Voltmeter [AM (MW)] Setting: Band switch : AM (MW) AM RF SSG L13 530 (531) kHz 1.7 V Confirmation 1,710 (1,602) kHz 8.5 V (9.0 V) no mark: US, CND Put the lead-wire antenna close to the set. level meter + – 0.01 µF L7 580 kHz (621 kHz) <621 kHz> CT2 1,490 kHz (1,404 kHz) <1,485kHz> no mark: US, CND i (headphone) jack (J301) ( ) : AEP, UK < > : E, SP, JE FM FREQUENCY COVERAGE ADJUSTMENT Adjustment Part Frequency Display Reading on Digital Voltmeter Confirmation 87.5 MHz <76.0 MHz> 2.3 V <1.5 V> Confirmation 108 MHz <108.0 MHz> 11 V <8.8 V> [FM] Setting: Band switch : FM FM RF SSG ) : AEP, UK, E, SP, JE Adjust for a maximum reading on level meter 32 Ω set 30% amplitude modulation by 400 Hz signal Output level: as low as possible ( AM (MW) TRACKING ADJUSTMENT no mark: US, CND, AEP, UK < > : E, SP, JE FM TRACKING ADJUSTMENT Adjust for a maximum reading on level meter MAIN board FM/SW Telescopic level meter Antenna (ANT1) 32 Ω + set – 22.5 kHz frequency deviation by 400 Hz signal Output level: as low as possible L14 87.5 MHz CT2 108.0 MHz SW FREQUENCY COVERAGE ADJUSTMENT Adjustment Part Frequency Display i (headphone) jack (J301) Reading on Digital Voltmeter L12 5.8 MHz 1.75 ± 0.1 V Confirmation 15.6 MHz 8.5 V ± 1 V ICF-CD2000S SW TRACKING ADJUSTMENT [SW] (ICF-CD2000S) Setting: Band switch : SW AM RF SSG 0.01 µF Adjust for a maximum reading on level meter MAIN board FM/SW Telescopic level meter Antenna (ANT1) 32 Ω + set – 30% amplitude modulation by 400 Hz signal Output level: as low as possible 5.8 MHz 15.6 MHz ICF-CD2000S Adjustment Location: MAIN board (See page 16) AM IF Adjustment Procedure: 1. Connect the IF swimmer scope as shown below. 2. Set the BAND switch to AM position. 3. Adjust the T1 so that the frequency of IF swimmer scope is 450 kHz and the waveform is symmetric in relation to the maximum value. i (headphone) jack (J301) digital voltmeter MAIN board TP (VT) L8 CT1 + – MAIN board 0.047 µF AM (MW) Ferrite-Rod Antenna (L7) • Repeat the procedures in each tracking adjustment several times, and the frequency coverage and tracking adjustments should be finally done by the trimmer capacitors. TP (DET OUT) IF swimmer scope IN OUT + 10 µF Adjustment Location: MAIN board (See page 16) – 15 – FM VCO Adjustment Setting: FM AUTO SCAN Adjustment Setting: FM RF SSG FM RF SSG 0.01 µF 0.01 µF MAIN board FM/SW Telescopic Antenna (ANT1) Carrier frequency: 98 MHz Modulation: no modulation Output level: 0.1 V (100 dB) Carrier frequency: 98 MHz Modulation: no modulation Output level: 0.1 V (100 dB) MAIN board FM/SW Telescopic Antenna (ANT1) Procedure: 1. Connect the frequency counter as shown the figure below. (Use a frequency counter having high input impedance) 2. Set the BAND switch to FM position. 3. Tune the set to 98 MHz. 4. Adjust RV1 for 76 kHz reading on the frequency counter. Procedure: 1. Connect the tester as shown the figure below. 2. Set the BAND switch to FM position. 3. Tune the set to 98 MHz. 4. Adjust RV2 for +0.275 V reading on the tester. 5. Make sure that the TP429 on LCD board is over 2.4 V. Specified Value: 75.5 to 76.5 kHz Specified Value: +0.274 to 0.276 V IC2 4 (VCO) Tester frequency counter LCD board RV1 TP9 R34 27 k Ω 240 k Ω TP418 (AFC) TP419 (REG) + – + – Adjustment Location: MAIN board AM AUTO SCAN Check In case of failure, check AM tracking adjustment and AM IF adjustment, as there is no place to be adjusted. Also, confirm that the TP16 on the MAIN board voltage is 3.3 V during auto scan and the TP429 on the LCD board is over 2.4 V at the reception of AM. Adjustment Location: MAIN board Adjustment and Check Location: – MAIN Board (Component side) – L13 AM (MW) FREQUENCY COVERAGE Adjustment L12 SW FREQUENCY COVERAGE Adjustment AM (MW) L7 TRACKING CT2 Adjustment TP (VT) FM TRACKING CT3 Adjustment L14 TP16 T1 AM IF RV1 Adjustment FM VCO Adjustment RV2 FM AUTO SCAN Adjustment – 16 – SW CT1 TRACKING L8 Adjustment – MAIN Board (Conductor side) – TP (DET OUT) TP9 TP (GND) – LCD Board (Conductor side) – TP444 (GND) TP418 (AFC) TP419 (REG) TP429 – 17 – Tracking Balance Check CD SECTION Precautions for Adjustment 1. Before beginning adjustment, set the equipment to service mode. After the completion of adjustment, be sure to reset the service mode. For more information, see “Service Mode (service program) ” on page 10. 2. Perform adjustments in the order given. 3. Use YEDS-18 disc (Part No.: 3-702-101-01) unless otherwise indicated. 4. Power supply voltage requirement: DC6 V in battery terminal VOLUME knob : Minimum MEGA BASS switch : OFF Before Beginning Adjustment Set the equipment to service mode (See page 11) and check the following. If there is an error, repair the equipment. Condition: • Hold the set in horizontal state. Check Procedure: oscilloscope (DC range) MAIN board TP (TE) TP (VC) (See page 14) 1. Put the disc (YEDS-18). 2. Connect the oscilloscope to TP (TE) and TP (VC) on the MAIN board. 3. Set the equipment to service mode stop state. (See page 11) 4. Confirm that the waveform on the oscilloscope becomes up/ down symmetrical with an axis of 0 V. Note: Take long sweep time for easy monitoring. • Checking of the sled motor 1. Open the upper panel. 2. Press the > and . keys and check that the optical pickup can move smoothly without sluggishness or abnormal noise in innermost periphery → outermost periphery → innermost periphery > : The optical pick-up moves outwardly. . : The optical pick-up moves inwardly. • Checking of focus searching 1. Open the upper panel. 2. Press the [CD u] key. (Focus searching operation is activated continuously) 3. Check the object lens of the optical pick-up for smooth up/ down motion without sluggishness or abnormal noise. 0V Check Location: MAIN Board (See page 20) digital voltmeter (DC range) MAIN board + – 1. Set the equipment to service mode stop state. (See page 11) 2. Connect the digital voltmeter to each test point on the MAIN board as follows. 3. Confirm that the reading on digital voltmeter satisfy specified value of each test point. Specified value +3 V 3.2 V +3.4 V 3.2 V DV 4.5 V MDV 2.6 V OPDV 1.75 V POWER +B 3.8 V PRE +B 3.8 V PRE VC 1.6 V A 0V B A=B 5. After the completion of adjustment, reset service mode. (See page 11) Check Procedure: Test point A 0.7 – 1.7 Vp-p B A=B VCC Check Use a SUM-3 battery for VCC check Each TP (See page 20) + – 4. After the completion of adjustment, reset service mode. (See page 11) Check Location: MAIN Board (See page 20) – 18 – SECTION 7 DIAGRAMS Focus bias Check Condition: • Hold the set in horizontal state. Check Location: 7-1. IC PIN FUNCTION DESCRIPTION – MAIN Board (Conductor Side) – • LCD BOARD IC401 LC867124A-5M74 (SYSTEM CONTROLLER, LCD DRIVER) Check Procedure: oscilloscope (AC range) MAIN board TP (RF) TP (VC) + – Pin No. Pin Name I/O 1 SHOCK O Pin No. Pin Name I/O C2 flag shock detection once danger signal output to the LC78626KE (IC502) “L”: shock detection danger 61 CE2 I Setting terminal for the model Not used 62 CE3 I Setting terminal for the model “L”: ICF-CD2000, “H”: ICF-CD2000S 63 J I Setting terminal for the model “H”: E, Singapore, Tourist model Description “H”: pause 2 PAUSE O Pause signal output to the LC78626KE (IC502) 3 WOK O D-RAM writing enable signal output to the LC78626KE (IC502) O Common drive signal output to the liquid crystal display (LCD401) 4 BUZ O Buzzer sound drive signal output terminal 68 VSS2 — Ground terminal 5 CORES O 69 VDD2 — Power supply terminal (+2.8V) 70 CD ON O Power on/off control signal output for the CD mechanism section 6 LMT I External reset signal output to the CD control signal counter (IC404) and LC78626KE (IC502) “L”: reset Sled limit-in detection switch (S603) input terminal 71 TU ON O Power on/off control signal output for the tuner section “L”: power on 72 A MUT O Audio line muting on/off control signal output terminal “L”: muting on “H”: writing enable (See page 14) 1. Put the disc. (YEDS-18) 2. Set the equipment to service mode stop state. (See page 11) 3. Connect the oscilloscope to the test point TP (RF) on the MAIN board. 4. Move the optical pick-up to the center by pressing the > and . keys. 5. Press the [BAND] key. (Both tracking and sled are turned ON) 6. Check the oscilloscope waveform is as shown below. A good eye pattern means that the diamond shape (◊) in the center of the waveform can be clearly distinguished. TP (+3.4V) RF Signal Reference Waveform (Eye Pattern) TP (+3V) VOLT/DIV : 200 mV (With the 10:1 probe in use) TIME/DIV : 500 ns TP (MDV) TP (DV) TP (OPDV) TP (RF) TP (GND) TP (PRE VC) To watch the eye pattern, set the oscilloscope to AC range and increase the vertical sensitivity of the oscilloscope for easy watching. TP (PRE +B) Check Location: MAIN Board (See page 20) – 20 – “L”: power on 7 RES I 8 XT1/P74 I Sub system clock input terminal (32.768 kHz) 73 LED ON O LED drive signal output of the liquid crystal display (LCD401) back light (D405 to D408) indicator SL – O Sled servo drive signal output to the LA9251M (IC501) 9 XT2/P75 O Sub system clock output terminal (32.768 kHz) 74 10 VSS1 — Ground terminal 75 SL + O Sled servo drive signal output to the LA9251M (IC501) 11 CF1 I Main system clock input terminal (3 MHz) 76 RCK O Serial data latch pulse signal output to the CD control signal counter (IC404) 12 CF2 O Main system clock output terminal (3 MHz) 13 VDD1 — Power supply terminal (+2.8V) 77 RWC O 14 KEY1 I Key input terminal (A/D input) S402, S403, S421, S422, S424 (WORLD/LOCAL, D.S.T. SUMMER T., ESP, CD PLAY MODE, CLOCK) keys input At tuner mode : PLL serial data latch pulse signal output to the FM/AM PLL (IC3) At CD mode : Reading/writing control signal output to the LC78626KE (IC502) (shumitt output) 78 COIN I At tuner mode : PLL serial data input from the FM/AM PLL (IC3) At CD mode : Command serial data input from the LC78626KE (IC502) 15 KEY2 I Key input terminal (A/D input) S711 to S715 (TUNE/SCAN TIME SET – ., ALARM TRACK/STATION, ALARM TIME, ALARM MODE, BAND) keys input 79 SQOUT O At tuner mode : PLL serial data output to the FM/AM PLL (IC3) At CD mode : Subcode Q data output to the LC78626KE (IC502) CQCK O KEY3 I Key input terminal (A/D input) S706 to S710 (STATION zSELECT/zPRESET 1/2/3/4/5) keys input 80 16 At tuner mode : PLL serial data transfer clock signal output to the FM/AM PLL (IC3) At CD mode : Subcode Q data reading clock signal output to the LC78626KE (IC502) 17 KEY4 I Key input terminal (A/D input) S701 to S705 (TUNE/SCAN TIME SET + >, SNOOZE SLEEP OFF/LIGHT, x OFF ALARM RESET, RADIO SLEEP, CD u ) keys input 18 OPEN I CD door open/close detection switch (S423) input terminal 19 AFC O AFC control signal output to the CXA1111N (IC1) when FM reception 20 REG I Input of monitor signal of constant-voltage power supply generated form CXA1111N (IC1) (A/D input) 21 BATT I Battery voltage detection input terminal 22 EMPN I D-RAM low capacity alarm signal input from the LC78626KE (IC502) 23 CNTOK I Data connection point detect completion signal input from the LC78626KE (IC502) “H”: detection completed (D-RAM writing starts) 24 OVR I D-RAM writing interruption signal input from the LC78626KE (IC502) (RZP pulse signal input in case of overflow or shock) 25 DRF I DRF (focusing detection) signal input from the LA9251M (IC501) 26 WRQ I Subcode Q output standby input from the LC78626KE (IC502) 27 C2F I C2 flag signal input from the LC78626KE (IC502) TP (TE) 7. Stop revolving of the disc motor by pressing the [x OFF ALARM RESET] key. 8. After the completion of adjustment, reset service mode. (See page 11) – 19 – TP (VC) 64 to 67 COM0 to COM3 System reset signal input from the reset signal generator (IC402) “L”: reset For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H” TP (POWER +B) RF level 0.9 to 1.3 Vp-p Description 28 AC IN I Power failure detection input terminal 29 SHIFT O Shift clock output of the main system clock (3 MHz) 30 BEEP MUTE O Beep sound muting on/off control signal output terminal 31 to 40 S4 to S13 O Segment drive signal output to the liquid crystal display (LCD401) 41 VDD3 — Power supply terminal (+2.8V) 42 VSS3 — Ground terminal 43 to 60 S14 to S31 O Segment drive signal output to the liquid crystal display (LCD401) – 21 – “L”: less capacity “L”: power on, “H”: power failure “H” active “L”: muting on – 22 – BLOCK DIAGRAM – CD Section – E E F RF– 47 18 RF SWITCH Q504 48 I/V 3 F 4 E BAL F RF DET VCA DEF FSTA LATCH EFBAL EFMI EFM LEVEL CONTROL DEFI 51 1 37 36 CONT3/SBCK 34 CONT4/SFSY 35 38 33 44 52 HFL 23 3 PDO LCHO 1BIT DAC L. P. F. RCHO SUB CODE CONTROL LDS 7 TES 43 TJP 40 TGL 41 TOFF 42 TH TA TES 24 JP+ 27 TGL 26 TOFF 25 10 D504 CLV DIGITAL SERVO 11 OUT2– F/R DRIVE 28 7 TD IN2 2 15 TO 13 RF AMP, FOCUS/TRACKING/ SPINDLE/SLED/SERVO IC501 5 MUTING Q506 (TRACKING) 6 BUFFER IC505 TRACKING SWITCH Q513 3 2 30 22 20 36 TIMING GENERATOR 69 B+ 59 43 42 OUT1+ OUT1– H FOCUS (FOCUS) F/R DRIVE IN1 1 17 FOCUS SERVO & FOCUS LOGIC FD FD– FA FA– FE FE– 18 19 20 21 22 M 36 35 H SLED M601 (SLED) OUT4+ F/R DRIVE IN4 33 28 SLD SLED SERVO OUT4– SL+ SLEQ SQ OUT WRQ PAUSE WOK CNTOK OVR SHOCK RWC C2F EMPN COIN CLOCK 64 67 SCLR SHIFT REGISTER SCK FMT FILTER LATCH RCK 11 15 RCK 12 APS/APC CONTROL IC601 (2/2) 37 OUT3+ OUT3– F/R DRIVE IN3 32 26 SPD SPINDLE SERVO 30 SLED SWITCH Q512 27 S/S START 27 SPINDLE SWITCH Q503-1 S603 (LIMIT) D503 28 MUTE B+ APC SWITCH Q602 ASP SWITCH Q606 B+ B+ SWITCH Q606 B+ B+ SWITCH Q607 25 B (Page 29) – 24 – H I 9 14 CDRES SL– FOCUS SWITCH Q502-1 SL+ FOCUS SWITCH Q501-1 DRF (Page 28) DNB-1 K – 23 – B+ B+ (CD 3.4V) DNB-2 15 SPINDLE SWITCH Q514 EXT DRV LMT SERVO SWITCH Q507 B+ SWITCH Q604,605 B+ SWITCH Q511 APC DRV 23 ASP DRV 17 SPINDLE SWITCH Q502-2 23 B+ D601 SLED SERVO Q509 33 STOP/START SWITCH Q610 B+ SP8 35 CLV 45 SP A (Page 29) SP– M 38 H SPINDLE M602 (SPINDLE) VZ VE 20 3 2 6 1 5 7 4 29 G (Page 30) SLED SWITCH Q503-2 SLOF D (Page 28) COUNTER IC404 D514 SL– SQ OUT 65 WRQ 66 PAUSE IN 77 WOK 76 CNTOK 75 OVF 74 SHOCK 80 RWC 62 C2F 46 EMPN 79 14 TRACKING SWITCH IC506 (2/2) TRACKING SWITCH IC506 (1/2) 63 OE WE CAS RAS X501 16.9344MHz 1 10 2-AXIS DEVICE 60 22 3 23 4 D-RAM IC503 SI 40 OUT2+ H TRACKING 41 JP– TRACKING SWITCH Q501-2 FOCUS/TRACKING COIL DRIVE SPINDLE/SLED MOTOR DRIVE IC601(1/2) µCOM INTERFACE SERVO COMMANDER F (Page 27) FMT TRACKING SERVO & TRACKING LOGIC TRACKING SWITCH Q505 CQCK OPTICAL PICK-UP BLOCK (DAX-11E) 6 COIN TE R-CH 55 OE 85 WE 86 CAS 87 RAS 88 XIN TE– D-RAM CONTROLLER SL MODE T OFF SL OFF RFS SP OFF SP MODE D MUTE HFL DRF XOUT LDD RES 62 DIGITAL SIGNAL PROCESSOR, CLV SERVO, D/A CONVERTER, D-RAM CONTROLLER IC502 APC CONTROL CONT5/PW AUTOMATIC POWER CONTROL Q601 LD CONT2 CLV+ LASER APC V/P 63 FSEQ PD PD E (Page 27) LASER DIODE LD L-CH 53 1, 2, 24, 25 DQ1 – DQ4 C 2 RF VCA FIN1 5, 9 – 12, 14 – 18 A1 – A9 C 1 DRAM0 – DRAM3 81 – 84 B : CD PLAY 49 AD0 – AD9 89 – 93, 95 – 99 B FIN2 • SIGNAL PATH EFMO SAMPLING/ DIGITAL FILTER A 17 DIGITAL ATT. SLC A 50 A/D PCM DECODER DETECTOR SLI DATA LIMIT CONVERTER SLC A/D PCM ENCODER 7-2. SYNC • DETECTOR EFM DEMODULATOR ICF-CD2000/CD2000S C (Page 30) (Page 30) (Page 29) – 25 – – 26 – B+ SWITCH Q608,609 B+ J (Page 30) ICF-CD2000/CD2000S BLOCK DIAGRAM – MAIN Section – D3 FM / AM FRONT-END IF DISCRI, IF AMP IC1 (2 / 2) FM / AM FRONT-END IF DISCRI, IF AMP IC1 (1/2) (CD2000) B. P. F BPF1 (CD2000S) 10 FM RF IN FM FRONT-END FM / AM FE OUT FM IF IN 15 CF3 10.7MHz 12 MPX IC2 DET OUT FM IF DISCRI 21 1 D12 D1 CT3, L14 FM TRACKING L14 FM RF CF1 10.7MHz CT3 7 2 D13 14 AM IF IN 5 D8 D9-1 FM OSC FM / AM SELECT D6 RF AMP Q1 L8 SW ANTENNA CT1 SW / MW SWITCH Q8 SYNC • DETECTOR 13 18 CT1, L8 SW TRACKING TUNER MUTE Q311 8 4 RV1 FM VCO CT2, L7 AM (MW) TRACKING 8 AM RF IN 7 R-CH 1 J301 MUTING Q102 MUTING Q103 BEEP MUTE Q310 HEADPHONE SWITCH Q312 B+ (CD3.4V) SP101 SPEAKER L CH D102 R-CH 20 AFC / AGC1 S301 MEGA BASS ON MUTING Q913 6 B+ SWITCH Q907 B+ B+ IC301 (2 / 4) 9 8 10 RV2 FM AUTO SCAN D5 7 TONE AMP IC301 (1 / 4), IC302 (2 / 2), IC303 (2 / 2), Q101, 201, 104, 204, 305 CT2 RF AMP Q3 POWER AMP IC101 RV301 VOLUME 5 OFF (CD2000) L7 AM (MW) FERRIRE-ROD ANTENNA 6 7 R-CH VCO STEREO DET Q10 AM IF DISCRI L15 6 LOW-PASS FILTER AMP IC303 (1 / 2) 3 Q11 MUTING METER 16 CF2 450kHz LCH OUT 9 RCH DECODER OUT 10 IN FM RF T1 AM IF (CD2000S) Q9 MUTING FM DISCRI MIX AMP IC302 (1 / 2) VCO ANT1 FM/SW TELESCOPIC ANTENNA PILOT MUTING CONTROL SWITCH Q910 B+ MUTING CONTROL SWITCH Q909 MUTING CONTROL SWITCH Q308, 309 SP102 SPEAKER R CH B+ SWITCH Q914 LCD401 (LIQUID CRYSTAL DISPLAY) AM FRONT-END D905 B+ B+ SWITCH Q908 64 – 67 COM0 – COM3 D10 L12 SW OSC SW SWITCH Q5 31 – 40, 43 – 60 S4 – S31 BUZZER DRIVE Q402, 415 BUZ 4 D405-408 (LCD BACK LIGHT) B+ B+ SWITCH Q905, 912 B+ MW SWITCH Q4 L12 SW FREQUENCY COVERAGE LED DRIVE Q403, 405, 411, 412 73 LED ON BEEP MUTE Q401 BEEP MUTE 30 SW SWITCH Q2 D901 D428 (1 / 2) SL+ 75 3 14 – 17 AM SOC KEY MATRIX S402, 403, 421, 422,424, 701-715 SYSTEM CONTROLLER, LCD DRIVER IC401 6 LMT 8 9 D401 B+ 26 WRQ 19 AFC 20 REG 20 XOUT REFERECE DIVIDER CCB I/F DO CL DI CE D425 (1 / 2) D423 (1 / 2) D424 (1 / 2) D426 (1 / 2) 4 3 2 1 TUNER ON SWITCH Q404 D404 TU ON 71 CD ON SWITCH Q410 D403 CF2 CD ON 70 78 80 79 77 27 22 2 3 23 24 8 9 5 25 11 12 3 +3.4V REGULATOR IC402 D903 B+ 2 – K (Page 23) – 28 – + D420 D421 BATT DET Q413, 414 B+ (CD3.4V) B+ 3 +3.3V REGULATOR 2 IC901 B+ : FM : AM (MW) : CD PLAY LEVEL SHIFT Q407, 408 C (Page 26) DRY BATTERY SIZE "AA" (IEC DISGNATION R6) 4PCS. 6V • SIGNAL PATH D409 X401 32.768kHz D BAT401 LITHIUM BATTERY 3V (FOR BACK-UP) SHIFT 29 X402 3MHz B04 LMT 13 XIN (Page 26) (Page 25) MUTING CONTROL SWITCH Q904 B (Page 25) (Page 25) VZ AOUT X1 75kHz D402 CF1 AIN 18 19 AUDIO MUTE Q406 D434 PHASE DETECTOR CHARGE PUMP J (Page 25) B+ B+ A MUTE 72 DRF MO / ST AM / FM (Page 26) D412 18 OPEN DRF 17 DATA SHIFT REGISTER LATCH G H I J901 DC IN 6V AM / FM IF MUT 5 7 IF IN 10 IC301 (4 / 4) 14 13 12 BATT 21 XT2 / P75 CDRES SW / MW 16 PD – 27 – SL- B+ D904 CDRES AM IN 12BITS PROGRAMMABLE DIVIDER S401 (OPEN MAIN) EMPN PAUSE WOK CNTOK OVR SHOCK 6 05 D429 AC IN 28 COIN CQCK SQOUT RWC C2F EMPN PAUSE WOK CNTOK OVR XT1 / P74 11 FM IN S423 OPEN RCK SL+ B+ RESET SIGNAL 2 GENERATOR IC403 B+ SWITCH Q301 D428 (2 / 2) D413 FM / AM PLL IC3 12 DC / DC CONVERTER Q74-76, T70 3 (CD2000) COIN COLK SQOUT RWC C2F L13 AM (MW) FREQUENCY COVERAGE MW SWITCH Q6 D425 (2 /2) D423 (2 /2) D424 (2 /2) D426 (2 /2) L13 AM (MW) OSC KEY1 - KEY4 D9-2 SL- 74 SHOCK 1 D433 RES 7 B+ SWITCH Q906 IC301 (3 / 4) 1 3 2 D427 RCK 76 WRQ F REG OUT E (Page 26) AM IF OUT (Page 26) BAND SELECT 7-3. A (Page 26) – 29 – – 30 – 7-4. ICF-CD2000/CD2000S PRINTED WIRING BOARDS – MAIN/JACK Boards – 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 • Semiconductor Location R25 BP504 BP501 BP502 C14 R16 C24 C11 C25 R15 C23 BCE C74 C73 C47 C76 C75 R801 R803 K R21 R45 C46 C48 R32 R13 C44 C45 + C43 R80 R79 R78 R77 C29 A A R44 C56 C42 + E CB FB3 R36 R35 R30 C55 + C54 R625 FB901 C912 C614 + C604 + C629 C607 L604 R640 C623 + C615 C616 L607 L608 C TP (PRE +B) R910 ECB Q906 C549 L504 C547 C548 C596 K A A D514 R599 – 32 – – 33 – BCE + C608 C494 R483 C419 R476 9 8 R477 IC404 A A + C515 C552 K 2E2B1C R558 R591 C554 Q502 R854 2E 2B 1C R565 C801 R568 2C 1B 1E R557 Q501 C505 R567 BCE R549 D504 C555 C568 + C551 16 R851 K A C569 C506 R566 2C1B 1E R501 1E 1B 2C C553 2C1B 1E BCE Q514 Q503 2E2B 1C 1 FB401 R576 Q507 R575 1-673-930- – 34 – 11 (11) R850 C502 C542 C543 + C533 + C536 R535 + C534 C535 L511 C564 + R539 R598 + C570 + C595 + L502 13 C493 L505 9 C582 C583 C597 C584 C585 5 + C561 Q513 C504 C559 C519 C309 1 C807 C806 C805 D512 1C 2B 2E C803 R584 + Q104 R123 C332 C565 C545 C520 1C1B 2C R345 + TP (TE) R524 C516 C113 R106 ECB TP (RF) R844 Q101 7 R911 14 R537 C557 IC303 16 IC503 R538 R536 R597 Q601 TP (VC) Q505 R546 C532 C531 C530 Q912 1E1B2C R219 TP ECB (PRE VC) 2C2B 1E R119 Q204 R223 C330 + C314 R343 R121 Q305 Q201 8 1 2E 2B 1C 1C2B 2E 22 L515 R569 C550 ECB L508 C590 C589 C588 C587 C586 C594 C593 C592 C591 A L609 14 R330 C318 Q312 R335 2C1B 1E R205 R206 C213 R632 + C811 A D901 Q203 + L514 C302 C303 + A R306 26 R304 R303 C577 C578 C579 C580 C581 A L501 R631 TP (GND) R545 + A A R360 D301 D102 D202 R552 R553 Q301 R305 C116 + R112 K Q310 E C B K C510 BCE A C301 BCE K 8 5 C319 BCE K R234 E CB R316 A R311 C115 R115 R124 R215 C320 R317 C324 C117 R134 L902 Q102 Q202 A K D203 A/K D204 ECB 1-673-930- C211 + 1 R321 4 K D103 A + C541 A/K K J301 11 (11) C118 C111 + L516 BCE R129 TP (IOP 1) D501 C619 TP (POWER +B) C609 A C610 B C617 05 – 31 – + C540 Q907 A R226 R126 L301 FB101 R111 K ECB R852 BP503 DC IN 6V R638 C618 A D905 K C334 7 11 1-673-933- (11) J901 – R478 C495 1 R117 3 R525 C103 + A/K E CB Q103 C329 8 IC302 A/K C322 R915 FB303 A D101 + C106 R639 K A R334 R233 R352 R351 R230 + C335 R211 D307 + C340 R128 FB201 R228 L513 FB301 R101 C203 + R28 R9 L903 R319 R218 K L19 C39 R27 C18 E BCE K DRY BATTERY SIZE “AA” (IEC DESIGNATION R6) 4PCS.6V R819 R820 R455 R817 FB304 FB102 1C 2B 2E R912 C906 RV301 D104 K FB302 50 A A Q905 VOLUME + C206 TP (MDV) C603 2 C910 C566 IC101 R914 K 14 A R601 C321 R347 R344 31 -2 C902 D304 A A Q914 R309 R349 C304 B E C317 51 R201 Q511 1E 1B 2C C204 C522 30 R835 R836 R577 R853 C518 7 A/K FB202 + -1 + R212 (CONDUCTOR SIDE) BCE Q512 R521 R511 C521 C216 + C217 R310 R307 R315 D201 R541 IC502 K R225 R125 BCE C517 Q910 R828 R827 R826 R825 R824 R823 8 R346 R318 R350 R513 R516 C513 R517 1 R302 R301 C104 K 5 K 1 Q908 D903 A 80 A A D503 32 R355 C338 8 IC301 + C316 X501 33 16 R529 C508 14 E CB 1 R359 81 1C 2B 2E + A C602 Q308 R308 100 1 C546 17 R909 IC201 R596 R570 Q509 C544 R562 1E 1B 2C R821 R834 R833 R832 R831 R830 R829 C562 + K R563 A C526 C802 R540 C512 OPEN 2C 1B 1E C810 R559 R586 S423 2E 2B 1C BCE Q504 L509 R526 R527 R509 R592 R593 C524 R531 IC501 R564 C507 R518 R519 R520 C573 R506 R507 R846 R818 + C556 4 R341 A A R356 C337 R348 R217 C539 C558 R530 R522 R523 4 C503 C514 3 IC505 C804 5 C511 R515 R512 R514 1 48 R504 R503 R554 4 IC506 5 49 1 R505 8 C574 L C529 + 64 Q506 B C E R588 K D502 R508 1 C538 C537 C527 C576 J R547 R533 R532 C525 R528 C575 + R550 R551 R574 R573 R571 R561 (RV502) D308 K 14 R338 C218 R357 R361 R560 C219 + C315 1 R229 K A K A R224 C215 50 R322 R336 + S DG C908 C901 R340 R116 R216 C328 2C 1B 1E Q311 2E 2B 1C 1 I Q609 MEGA BASS R905 2E 2B 1C A A R623 S301 C 3 2 OFF Q309 D428 K FB902 R637 TP (+3V) Q608 3 1 1 2C1B 1E L512 E C B C94 C86 C93 4 + R339 C B E ON OPTICAL PICK-UP BLOCK (DAX-11E) D427 A A JACK BOARD C622 TP (OPDV) C119 2 K Q913 A C224 1 C613 + IC901 CN602 2 K + 2 Q607 Q909 C331 + 1 C904 + 5 L601 M H 1 A K K A C601 M602 (SPINDLE) R92 C85 R34 R90 L606 C95 L602 1-673-933- 11 C605 11 (11) R88 + Q75 B C E R105 1 R91 L603 C325 R342 R213 R113 12 R913 44 + 2 Q74 B C E C333 1 C B E + C620 R635 TP R636 (DV) R628 C621 TP R605 (+3.4V) B C E CN601 2 Q602 C342 2 D601 A R222 R220 1 T70 DC/DC CONVERTER C92 C102 C202 E C B A R482 K R602 1 Q606 IC601 M R87 22 Q604 A A R40 R916 34 2 ESP R89 R630 M601 (SLED) G C612 R629 A A R582 D433 R39 Q76 S421 ECB 1 23 + K R908 2 33 2 A ECB 1 1 D70 L74 CN603 10 L72 L901 R627 C84 S603 (LIMIT) 6 BCE C627 C40 R29 C60 A R624 C87 A K D429 1E1B 2C (CD2000S) D71 D602 Q605 A A K Q603 C905 K Q610 C51 + A X1 Q2 TP9 C83 C911 A IC2 C201 L605 D902 K + C88 A K K (CD2000S) + C49 R423 C611 C81 C80 R75 1C2B 2E R53 + R481 1 A A A L70 CF1 TP (DET OUT) C907 C53 C52 RV1 FM VCO 5 C101 E CB Q9 R608 R615 C625 R616 F (COMPONENT SIDE) R641 C606 JACK BOARD C626 + BCE Q11 K R358 Q904 (CD2000S) (CD2000:E, SP, JE) R95 R33 C50 A A 24 D434 D423 D424 D425 D426 (CD2000S) R11 R23 13 S422 CD PLAY MODE BCE D904 D14 CF3 R10 R626 2C1B 1E 2C 1B 1E Q10 2E K 2B 1C A R634 E D8 R486 CF2 L18 FB1 IC1 C41 + L17 R70 FB2 K T1 AM IF CERAMIC (CD2000:E, SP, JE) C28 L14 FM RF 1 12 * C56 METAL (CD2000:US, CND/CD2000S) (CD2000S) L15 C36 D6 C8 C7 C17 C59 D430 K C32 Q6 Q5 + C341 10 C71 A C31 * R42 D13 A K 1 36 Q1 C19 A 1 RV2 FM AUTO SCAN R4 L73 CN301 L20 (Page 42) R5 A D1 A/K A + C34 R71 IC3 L8 SW ANTENNA R37 TP16 S424 CLOCK CT1 *C21 R1 R14 K C30 A C57 E CB 11 A (CD2000S) CD2000:E, SP, JE/ CD2000S C89 D C91 C9 R20 C6 L4 C3 L5 C5 + C4 D10 (CD2000) C35 K C1 L2 D12 K BPF1 B P F D9 K A R19 A C82 C90 R43 R7 S DG E CB R41 C10 R24 L11 CT2 R8 C33 R93 C78 20 LCD BOARD CN401 CN • U : B+ Line. • H : adjustment for repair. • Power voltage is dc 6 V and fed with regulated dc power supply from external power Voltage jack. • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM ( ) : AM (MW) 〈〈 〉〉 : SW [ ] : CD PLAY : Impossible to measure ∗ • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. • Circled numbers refer to waveforms. • Signal path. F : FM f : AM (MW) J : CD PLAY • Abbreviation CND : Canadian model JE : Tourist model SP : Singapore model C79 C72 R81 C77 R82 C572 Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce por tant le numéro spécifié. * D3 *D5 R3 R594 Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. * C2 CERAMIC (CD2000S) CT3 TP (VT) L11 R18 2E 2B 1C Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • % : indicates tolerance. f : internal component. • • C : panel designation. C14 * C2, METAL (CD2000) R2 CERAMIC (CD2000S) A A C22 DIODE (CD2000S) (CD2000S) (COMPONENT SIDE) (CD2000) K D5 * D3, SHORT (CD2000) (CD2000S) MAIN BOARD (CD2000S) R6 C12 L13 AM (MW) OSC L10 BCE (CD2000S) (CD2000S) * C21 METAL (CD2000) * Q3 L3 C26 L12 SW OSC Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated. Q4 (CD2000S) (CD2000) R12 R38 C C15 Q8 ANT1 FM/SW TELESCOPIC ANTENNA + Caution: Pattern face side: (Conductor Side) Parts face side: (Component Side) C16 + C27 R17 B (CD2000S) R26 L7 AM (MW) FERRITE-ROD ANTENNA (CONDUCTOR SIDE) ECB MAIN BOARD Note on Printed Wiring Boards: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. • W : indicates side identified with part number. z • : Through hole. f • : internal component. • b : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) C13 A R118 R130 R133 C120 C124 C220 C123 R110 R109 C105 R210 C205 C223 R209 R108 R208 C114 C214 R103 R202 R102 R203 R107 C212 R207 C112 R104 R127 R227 R204 R353 C327 R221 D-16 F-11 D-9 I-17 I-9 J-9 K-10 K-16 L-21 J-4 K-6 K-20 J-2 J-1 G-9 H-15 Location K-13 J-2 L-23 J-5 K-8 L-3 J-25 L-23 I-25 F-17 F-18 F-10 F-10 G-10 G-17 H-16 H-16 F-9 E-8 J-16 L-18 I-16 H-16 G-15 K-8 K-18 E-18 I-17 R74 IC1 IC2 IC3 IC101 IC201 IC301 IC302 IC303 IC404 IC501 IC502 IC503 IC505 IC506 IC601 IC901 Ref. No. Q505 Q506 Q507 Q509 Q511 Q512 Q513 Q514 Q601 Q602 Q603 Q604 Q605 Q606 Q607 Q608 Q609 Q610 Q904 Q905 Q906 Q907 Q908 Q909 Q910 Q912 Q913 Q914 C628 D-15 D-17 B-16 B-17 C-17 C-17 B-16 E-10 E-9 E-10 G-11 G-11 F-15 K-17 J-16 K-12 K-18 K-17 J-16 K-15 K-18 I-18 K-10 I-18 H-10 J-17 I-8 K-16 K-24 K-23 L-23 J-4 R120 Location Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 Q10 Q11 Q74 Q75 Q76 Q101 Q102 Q103 Q104 Q201 Q202 Q203 Q204 Q301 Q305 Q308 Q309 Q310 Q311 Q312 Q501 Q502 Q503 Q504 R83 R84 R85 Ref. No. E-19 D-19 J-25 J-5 K-5 K-22 K-22 L-20 F-17 F-9 J-19 F-2 I-15 E-9 I-17 C418 Location D433 D434 D501 D502 D503 D504 D512 D514 D601 D602 D901 D902 D903 D904 D905 K Ref. No. D-15 C-15 C-16 D-16 D-15 B-17 B-17 C-16 C-17 E-9 F-11 F-11 K-9 J-16 I-18 D-12 K-9 J-16 I-18 K-15 J-18 J-10 K-15 I-8 D-20 D-20 D-20 D-20 E-20 E-20 D-20 D-7 A Location D1 D3 D5 D6 D8 D9 D10 D12 D13 D14 D70 D71 D101 D102 D103 D104 D201 D202 D203 D204 D301 D304 D307 D308 D423 D424 D425 D426 D427 D428 D429 D430 C417 Ref. No. TP (IOP 0) ICF-CD2000/CD2000S 7-5. SCHEMATIC DIAGRAM – MAIN/JACK Boards – • See page 48 for Waveforms. • See page 49 for IC Block Diagrams. (Page 45) – 35 – – 36 – – 37 – – 38 – – 39 – ICF-CD2000/CD2000S PRINTED WIRING BOARDS – LCD/KEY Boards – 6 7 8 B LCD BOARD (COMPONENT SIDE) 11 12 13 14 15 16 17 18 19 20 21 22 23 Ref. No. D401 D402 D403 D404 D405 D406 D407 D408 D409 D410 D411 D412 D413 D417 D419 D420 D421 D422 D450 D451 Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated. C S402 S402 WORLD/ LOCAL Location G-18 F-5 F-5 F-6 C-23 D-23 C-15 D-15 G-18 G-8 G-20 F-18 H-8 F-20 F-20 H-20 H-19 G-20 E-14 E-14 25 26 KEY BOARD Ref. No. IC401 IC402 IC403 Location F-7 G-17 G-19 Q401 Q402 Q403 Q404 Q405 Q406 Q407 Q408 Q410 Q411 Q412 Q413 Q414 Q415 I-8 J-8 F-18 F-20 F-17 F-20 G-18 G-18 F-20 E-14 D-14 H-20 H-20 J-7 27 28 29 30 KEY BOARD (COMPONENT SIDE) 31 32 (CONDUCTOR SIDE) SNOOZE SLEEP OFF/LIGHT LCD BOARD (CONDUCTOR SIDE) D405 D407 D407, 408 (LCD BACK LIGHT) D405, 406 (LCD BACK LIGHT) OFF ALARM RESET S403 RADIO SLEEP D. S. T. SUMMER T. S403 R426 R452 R427 R431 D408 Q412 R451 R497 B C E R498 D406 R428 R429 R702 A K R703 R704 A LCD401 (LIQUID CRYSTAL DISPLAY) R493 K S715 Q411 BAND BAT401 LITHIUM BATTERY 3V (FOR BACK-UP) R430 C496 + B C E R475 D451 (CHASSIS) 1 32 D450 5 D422 + – 41 – S708 S709 E CB Q413 ECB Q414 S706 S707 TP445 (CD TEST 1) R706 R705 TUNE/SCAN TIME SET + K TUNE/SCAN TIME SET – R713 R434 R445 S701 5 1 R714 CN701 D421 S711 R444 D411 R436 R496 R446 R701 1 R715 R710 R488 11 (11) 1-673-932- 11 (11) – 43 – S713 ALARM TIME R712 R709 ALARM MODE S712 C486 C447 1-673-931- – 42 – 1 S706 SP101 (SPEAKER LCH) 1-673-932- 05 – 40 – 2 S707 BLK ALARM TRACK/STATION C479 C480 + 11 (11) S708 BRN Q402 1-673-931- S709 STATION SELECT/ PRESET A K C426 R755 A C427 C428 K R469 R468 R459 C407 – C482 C481 BCE R463 R449 R448 R447 BCE R708 S714 R484 C472 C473 R751 J Q415 3 TP429 C483 Q401 4 R707 CN403 R467 BCE R487 R437 L405 TP419 (REG) 5 I 3 C406 A A (Page 32) TP446 (TUNER TEST) D420 R454 S401 C488 C487 1 K R754 1 CN401 (OPEN MAIN) D417 TP447 (CD TEST 2) A K R418 R499 TP418 (AFC) A BCE Q404 Q406 C490 IC403 X401 MAIN BOARD CN301 C420 TP453 (RESET) C412 R443 R441 R442 R440 C445 C446 R416 R417 R409 R410 C477 R479 R473 R450 Q408 C401 + D413 C478 R415 R414 A 36 K C489 3 1 A S710 A R474 R492 R491 R490 R489 R408 R411 R412 C476 C474 C475 IC402 R461 R433 R419 R420 C484 R421 C485 R422 C415 R413 R460 D409 Q407 24 R480 R424 C443 + C405 + C403 C413 R432 K – E CB SP201 (SPEAKER RCH) BCE Q410 R471 R472 (CD2000) R750 X402 E CB BLK D410 R439 R438 A C402 1 L402 A K 25 L401 K D401 + C414 R404 BCE C411 C410 C409 C408 BRN L403 IC401 R402 R403 R457 R458 + (CD2000:US, CND/CD2000S) A 80 (CD2000S) K A + C442 R435 R453 BCE TP444 (GND) C444 Q403 R495 K BCE D412 K D403 R405 Q405 TP449 (GND) 40 R401 C470 R406 C471 R407 H C422 65 C421 A R464 K R465 A A K R466 G 41 R470 D419 + C469 C468 C467 C466 C465 D402 D404 64 (CD2000:E, SP, JE) L404 + TP448 (CD TEST 3) F 33 CD D E 24 R711 Caution: Pattern face side: (Conductor Side) Parts face side: (Component Side) 10 • Semiconductor Location Note on Printed Wiring Boards: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. z • : Through hole. • b : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) A 9 S705 5 04 4 S7 3 S710 2 S702 1 S703 7-6. – 44 – 11 (11) 6-7. ICF-CD2000/CD2000S SCHEMATIC DIAGRAM – LCD/KEY Boards – • See page 42 for Waveforms. Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • % : indicates tolerance. • C : panel designation. • U : B+ Line. • Power voltage is dc 6 V and fed with regulated dc power supply from external power voltage jack. • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM [ ] : CD PLAY ∗ : Impossible to measure • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. • Circled numbers refer to waveforms. • Signal path. F : FM • Abbreviation CND : Canadian model JE : Tourist model SP : Singapore model (Page 36) – 45 – – 46 – – 47 – • IC Block Diagrams – MAIN Board – AM IF BAND R L M/ST STLED GND NC LDS LDD BH1 PH1 LF2 VR 19 18 17 16 15 14 13 10 9 8 7 6 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 RIPPLE FILTER 2 Vp-p REF VCA 48 RF– I/V + – FF 0º PHASE COMPALATE 1 2 3 4 5 6 7 8 9 10 11 12 DISCRI AM OSC AFC FM OSC REG FM RF AM RF NC FM IN EARTH MIX OUT BAL VCA 47 RF RF AMP 46 GND 1 2 3 4 5 VCC VCO NC VCO STOP FILTER FM.FE V.C.O IN AM.FE EARTH 1.2 Vp-p RF DET + – TE– 6 TE 7 TESI SCI TH TA TD– 8 9 10 11 12 TE 45 CLV 44 HFL 43 42 41 40 T. SERVO &T. LOGIC 3.4 Vp-p TES TOFF TGL TJP + – Approx. 360 mVp-p FF 1/2 1 2 3 4 TB 5 TUNING METER 2 IC401 qs (CF2) 1 V/DIV, 100 ns/DIV FIN2 FIN1 E F STEREO SWITCH FF 90º 30.6 µs 7 IC601 8 (OSC) (CD Play Mode) 500 mV/DIV, 5 µs/DIV 2 IC501 7 (TE) (CD Play Mode) 200 mV/DIV, 5 ms/DIV APC SLC AM.IF DET.AGC FM.IF DISCRI 59.2 ns 49 – + LAMP TRIGGER SYNC DET DECODER REGULATOR DEF SLI FM IF 20 FSC DRF TUNE 21 TBC EARTH 22 REFI VCC FSS IF 23 BAND SIGNAL OUTPUT CIRCUIT 13.3 µs LA9251M-MPB 24 3.6 Vp-p 1.8 Vp-p IC501 LA3335M AFCW IC2 SLC CXA1111N AFCJ IC1 1 IC401 8 (XT1/P74) 500 mV/DIV, 10 µs/DIV DET 6 IC502 tl (XOUT) (CD Play Mode) 1 V/DIV, 20 ns/DIV FILTER 1 IC3 ql (XIN) (Radio ON Mode) 500 mV/DIV, 5 µs/DIV VCC – LCD Board – MUTE • Waveforms – MAIN Board – 39 NC 38 LASER TD 13 37 FSTA 36 EFBAL + – LATCH JP 14 19 XIN 5.4 Vp-p 600 mVp-p + – + – 22 23 24 25 26 27 28 29 30 31 32 I02 9 SLEQ SLD SL– SL+ LATCH POWER ON RESET 14 VDD 13 B04 QH 8 QG I01 15 VSS UNLOCK DETECTOR QF 7 QE B03 GND 1 UNIVERSAL COUNTER 670 mVp-p SWALLOW COUNTER 1/16,1/17 4BITS 1/2 12 FMIN 2 3 4 5 6 7 8 PARALLEL DATA OUTPUT 11 AMIN 26.6 ms 5 IC501 rj (RF), IC502 qk (EFMI) (CD Play Mode) 500 mV/DIV, 500 ns/DIV IFIN 10 384 ns 1.2 Vp-p – 48 – – 49 – – 50 – OSC NC 21 SP– SPD 20 SHIFT REGISTER 18 AOUT 17 AIN 16 PD QD 6 PHASE DETECTOR CHARGE PUMP QC B02 12BITS PROGRAMMABLE DIVIDER QB 9 Q74 (Base), Q75 (Collector) (Radio ON Mode) 200 mV/DIV, 200 ns/DIV 5 DATA SHIFT REGISTER LATCH 386 ns 18 19 REFERENCE DIVIDER B01 4 IC501 ea (OSC) (CD Play Mode) 200 mV/DIV, 10 ms/DIV 17 SP SPG 9 FE– 10 33 SLOF FE 11 34 TGRF + – FA– 12 TO 15 NC 16 + – 35 SP8 SLED SERVO FD– FA SERIAL DATA OUTPUT 13 + – SPINDLE SERVO FD RESET + – SHIFT CLOCK 14 F. SERVO &F. LOGIC SQH 20 XOUT 16 15 VCC LATCH CLOCK CCB I/F OUTPUT ENABLE 1 2 3 4 TC74VHC595FT (EL) SERIAL DATA INPUT Approx. 560 mVp-p CE DI CL DO IC404 LC72137M-TLM A 8 Q74 (Collector) (Radio ON Mode) 2 V/DIV, 200 ns/DIV IC3 PARALLEL DATA OUTPUT 32.9 ns QA 9.5 µs 3 IC501 wa (FE) (CD Play Mode) 200 mV/DIV, 20 ms/DIV DRAM3 DRAM2 DRAM1 DRAM0 LC78626KE VDD A0 A1 A2 A3 A4 VSS A5 A6 A7 A8 A9 RAS CAS WE OE IC502 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 DATA WIDTH CONVERSION DEFI 1 OVERFLOW PROCESS STARTING CONTROL TAI 2 PDO VVSS ISET VVDD FR 3 4 5 6 7 VSS TESCLK TESA TESB TESC TESGB TEST5 CS TEST1 8 9 10 11 12 13 14 15 16 EFMO 17 EFMI 18 VCO CLOCK OSCILLATION SHOCK DETECTION 80 79 78 77 76 75 74 73 72 71 70 DRAM CONTROL CLOCK CONTROL SHOCK EMPN NGJ PAUSEIN WOK CNTOK OVF MMC3 MMC2 MMC1 MMC0 69 RES RAM ADDRESS GENERATOR SLICE LEVEL CONTROL ADPCM ENCODER ADPCM DECODER 68 EMPP 67 FMT µCOM INTERFACE DIGITAL ATTENUATER 2KX8 BIT RAM 66 WRQ 65 SQOUT TEST2 19 HFL TES TOFF TGL JP+ JP– CLV DIGITAL SERVO 64 CQCK 63 COIN 62 RWC SERVO COMMANDER 23 24 25 26 27 28 X4 OVER SAMPLING DIGITAL FILTER INTERPOLATION MUTING SYNCHRONISM DETECTION EFM DEMODULATION PCK 29 FSEQ 30 GENERAL PURPOSE PORT C1, C2 ERROR DETECTION& CORRECTION FLAG PROCESS NODE DETECTION SUBCODE ISOLATION QCRC 1BIT DAC XTAL SYSTEM TIMING GENERATOR PROHBITION 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 VDD ASRES CONT2 CONT3/SBC CONT4/SFSY CONT5/P SBSY TEST3 DOUT TEST4 16M 42M EFLG FSX EMPH TOUT MR1 TESE TESD DIGITAL OUT – 51 – C2F CLV+ 20 CLV– 21 V/P 22 L.P.F. 61 60 59 58 XVSS XIN XOUT XVDD 57 56 55 54 53 52 51 MUTER RVDD RCHO L/RVSS LCHO LVDD MUTEL – + IN2 2 – + OUT1+ OUT1– OUT2+ OUT2– PGND OUT3+ OUT3– OUT4+ OUT4– SL MODE 44 43 42 41 40 39 38 37 36 35 34 H FOCUS H TRACKING H SPINDLE H SLED FORWARD REVERSE DRIVE FORWARD REVERSE DRIVE FORWARD REVERSE DRIVE FORWARD REVERSE DRIVE 33 IN4 + – IN1 1 1CH/2CH LB8118M + – IC601 32 IN3 VOUT1 3 31 VOUT2 PWM – + INVERSION OUTPUT + – + – CHG DRY 5 30 ASP REF CLUMP+ OFFSET CHG MON 6 CLUMP+ OFFSET OR 28 MUTE GND 7 1.2V + – ERROR AMP ERROR AMP SAWTOOTH OSCILATION + – PWM + – ERROR AMP + – PWM + – PWM 1.2V DEAD TIME PWM STARTING ERROR AMP 1.2V PWM 27 S/S 26 VOC 25 VLD 24 VAPC 23 APC DRV – + DEAD TIME VEXT 10 ASP REF TSD + – EXT DRN 9 + – + – OSC 8 + – DEAD TIME ERROR AMP 29 SL REF + – + – 1.2V ERROR AMP MAXIMUM VALUE 1CH/2CH CHARGE -OVER + – MAXIMUM VALUE VCD 4 EXTERNAL VOLTAGE JUDGMENT FORCED STARTING SW VEXT-OHG 11 0.7V + – IC901 17 18 19 20 21 22 VASP UPBASE VZ BO BI 16 ASP DRV 15 VO SET CHG-ON 14 DB2 13 DB1 12 EXTBASE VREF 2.7V RN5RZ33BA-TR GND 1 5 CE VDD 2 VREF – + CURRENT LIMIT VOUT 3 4 NC – 52 – SECTION 8 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they may have some difference from the original one. • Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE) . . . (RED) ↑ ↑ Parts Color Cabinet's Color • Abbreviation CND : Canadian model JEW : Tourist model SP : Singapore model (1) • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • The mechanical parts with no reference number in the exploded views are not supplied. • Accessories and packing materials are given in the last of the electrical parts list. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiquens pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. GENERAL SECTION 13 14 10 9 11 8 7 16 12 3 6 5 17 15 4 2 1 12 Ref. No. 1 2 3 4 5 6 7 8 9 Part No. 3-368-852-01 3-318-203-71 3-033-558-01 3-033-554-01 3-934-442-01 Description FOOT SCREW(B1.7X5), TAPPING HOOK (OPEN) KNOB (OPEN) SPRING, TENSION 3-033-578-01 3-033-553-01 X-3377-220-1 3-038-974-01 SPRING (LOCK) BUTTON (CD OPEN) LID ASSY, CD SHEET (CD) Remark Ref. No. 10 11 12 13 14 Part No. 3-033-575-01 3-033-572-01 4-356-741-21 3-033-556-01 X-3378-356-3 * 15 16 17 A-3663-312-A KEY BOARD, COMPLETE X-3377-219-1 CABINET (UPPER) ASSY 3-040-690-01 SPRING (LID) – 53 – Description PANEL (CD) SPRING (CD OPEN) SCREW, TAPPING (BIND 2X8) COVER SHAFT ASSY Remark (2) LCD BOARD SECTION 63 73 59 63 69 67 60 77 68 72 65 70 70 77 71 74 LCD401 70 58 70 54 78 53 75 55 56 56 56 61 53 SP101 SP201 76 51 Ref. No. 51 53 54 55 * 56 Part No. 3-033-576-11 3-035-203-01 X-3378-281-1 3-033-561-01 3-934-436-01 Description WINDOW (LCD) SHEET (SP), ELECTROSTATIC CASE (LITHIUM), BATTERY BUTTON (LITHIUM) HOOK (SP) 58 * 59 * 59 * 59 60 3-033-564-01 A-3683-085-A A-3683-087-A A-3683-103-A 3-033-565-01 TERMINAL (LITHIUM +), BATTERY LCD BOARD, COMPLETE (US, Canadian) LCD BOARD, COMPLETE (E, SP, JEW) LCD BOARD, COMPLETE (CD2000S) TERMINAL (LITHIUM -), BATTERY 61 63 65 67 68 Remark 3-043-413-01 CUSHION (SHIELD CASE) 4-356-741-21 SCREW, TAPPING (BIND 2X8) 1-791-188-11 WIRE (FLAT TYPE) (5 CORE) (CD2000: US, CND/CD2000S) 3-033-545-01 PLATE, LIGHT GUIDE 3-033-560-01 HOLDER, LCD Ref. No. 69 70 71 72 73 Description Remark SHEET (LCD) SCREW (B1.7X5), TAPPING SCREW (B1.4X2.3), TAPPING WIRE (FLAT TYPE) (36 CORE) (CD2000: US, CND/CD2000S) X-3377-783-1 CABINET (REAR) ASSY (CD2000) 73 74 75 76 77 X-3377-784-1 3-934-781-01 3-033-555-01 X-3377-221-1 3-825-652-01 CABINET (REAR) ASSY (CD2000S) SPRING (OFF SW) BUTTON (OFF-SW) CABINET (FRONT) SUB ASSY SPACER (A) 78 LCD401 SP101 SP201 X-3378-282-1 1-803-591-11 1-505-311-11 1-505-311-11 CASE (LCD), SHIELD ASSY DISPLAY PANEL, LIQUID CRYSTAL SPEAKER (4cm) SPEAKER (4cm) – 54 – Part No. 3-033-573-01 3-318-203-71 3-895-823-01 1-791-189-11 (3) MAIN BOARD SECTION CDM-2911EBA L7 108 108 118 109 108 105 110 121 111 107 not supplied 106 119 104 not supplied ANT1 120 112 102 113 103 114 115 101 116 Ref. No. 101 101 102 103 104 * 105 * 105 * 105 * 106 107 108 109 Part No. Description 3-033-547-11 3-033-547-21 3-033-570-01 3-033-569-01 3-040-780-01 CABINET (LOWER) (CD2000) CABINET (LOWER) (CD2000S) TERMINAL (-), BATTERY TERMINAL (+), BATTERY SHEET, ELECTROSTATIC A-3683-084-A MAIN BOARD, COMPLETE (CD2000: US, CND) A-3683-086-A MAIN BOARD, COMPLETE (CD2000: E, SP, JEW) A-3683-102-A MAIN BOARD, COMPLETE (CD2000S) 1-673-933-11 JACK BOARD 3-318-203-71 SCREW (B1.7X5), TAPPING 3-040-426-01 INSULATOR 3-040-409-01 SHEET (CHASSIS), ELECTROSTATIC Remark Ref. No. Part No. Description 110 111 112 113 114 3-033-549-01 3-033-571-01 3-033-574-01 3-033-550-01 3-033-552-01 CHASSIS TERMINAL (+ -), BATTERY CUSHION (BATTERY CASE LID) LID, BATTERY CASE BUTTON (CD) 115 116 118 119 120 3-370-475-01 3-033-562-01 4-356-741-21 3-039-164-01 3-040-410-01 SCREW (NYLOCK +B 3X6) KNOB (MEGABASS) SCREW, TAPPING (BIND 2X8) SHEET (SHIELD B), INSULATING CUSHION (SHIELD B) 121 ANT1 L7 3-033-563-01 TERMINAL BOARD, ANTENNA 1-501-222-71 ANTENNA, TELESCOPIC (FM/SW) 1-754-065-11 ANTENNA, FERRITE-ROD AM (MW) – 55 – Remark (4) MECHANISM DECK SECTION (CDM-2911EBA) not supplied 156 157 M602 M601 158 155 S603 159 160 153 154 152 161 151 162 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. 151 152 153 154 155 156 * 157 158 Part No. Description A-3303-970-A 3-318-203-11 4-972-163-04 1-783-093-11 7-627-850-17 SCREW ASSY, FEED SCREW (B1.7), TAPPING SPRING, SLED LEAD (WITH CONNECTOR) SCREW, PRECISION +P 1.4X2.5 3-719-401-11 SCREW (B1.7), TAPPING 4-984-320-01 CHASSIS 4-974-003-01 GEAR (B) Remark Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. Ref. No. Part No. Description 159 0 160 161 162 M601 1-667-512-11 X-4950-476-1 4-972-165-01 4-973-631-01 A-3328-100-A SLIDE FLEXIBLE BOARD OPTICAL PICK-UP (DAX-11E) RACK SCREW MOTOR ASSY, SLED M602 S603 – 56 – Remark A-3320-642-A MOTOR ASSY, TURN TABLE (SPINDLE) 1-571-099-21 SWITCH (1 KEY) (LIMIT) SECTION 9 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable • Abbreviation CND : Canadian model JE : Tourist model SP : Singapore model Ref. No. Part No. * 1-673-933-11 JACK BOARD *********** • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • SEMICONDUCTORS In each case, u: µ, for example: uA. . : µA. . uPA. . : µPA. . uPB. . : µPB. . uPC. . : µPC. . uPD. . : µPD. . • CAPACITORS uF: µF • COILS uH: µH Description Remark Ref. No. R714 R715 Part No. 1-107-826-11 CERAMIC CHIP 1-107-826-11 CERAMIC CHIP 1-107-826-11 CERAMIC CHIP 0.1uF 0.1uF 0.1uF 10% 10% 10% S701 16V 16V 16V 8-719-974-51 DIODE SB20-03P 1-469-568-21 FERRITE 1-469-568-21 FERRITE Les composants identifiés par une marque 0 sont critiquens pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. When indicating parts by reference number, please include the board. Description Remark 1.5K 1.5K 5% 5% 1/16W 1/16W S703 S704 S705 1-692-453-11 SWITCH, KEY BOARD (TUNE/SCAN TIME SET +, >) 1-692-453-11 SWITCH, KEY BOARD (SNOOZE, SLEEP OFF/LIGHT) 1-692-453-11 SWITCH, KEY BOARD (x OFF, ALARM RESET) 1-692-453-11 SWITCH, KEY BOARD (RADIO SLEEP) 1-692-453-11 SWITCH, KEY BOARD (CD u) S706 S707 S708 S709 S710 1-692-453-11 1-692-453-11 1-692-453-11 1-692-453-11 1-692-453-11 S702 < FERRITE BEAD > FB901 FB902 LCD < SWITCH > < DIODE > D902 KEY The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. 1-216-823-11 METAL CHIP 1-216-823-11 METAL CHIP < CAPACITOR > C910 C911 C912 JACK 0uH 0uH SWITCH, KEY BOARD (1) SWITCH, KEY BOARD (2) SWITCH, KEY BOARD (3) SWITCH, KEY BOARD (4) SWITCH, KEY BOARD (5) < JACK > S711 J901 1-778-153-21 JACK, DC (POLARITY UNIFIED TYPE) (DC IN 6V) < COIL > L901 1-416-668-11 INDUCTOR 10uH ************************************************************** A-3663-312-A KEY BOARD, COMPLETE ******************** * 1-692-453-11 SWITCH, KEY BOARD (TUNE/SCAN TIME SET –, .) S712 1-692-453-11 SWITCH, KEY BOARD (ALARM TRACK/STATION) S713 1-692-453-11 SWITCH, KEY BOARD (ALARM TIME) S714 1-692-453-11 SWITCH, KEY BOARD (ALARM MODE) S715 1-692-453-11 SWITCH, KEY BOARD (BAND) ************************************************************** A-3683-085-A LCD BOARD, COMPLETE (CD2000: US, CND) A-3683-087-A LCD BOARD, COMPLETE (CD2000: E, SP, JE) A-3683-103-A LCD BOARD, COMPLETE (CD2000S) ******************** * * * < CONNECTOR > CN701 1-569-806-21 CONNECTOR, FPC 5P 3-033-545-01 3-033-560-01 3-033-564-01 3-033-565-01 3-033-573-01 < RESISTOR > PLATE, LIGHT GUIDE HOLDER, LCD TERMINAL (LITHIUM +), BATTERY TERMINAL (LITHIUM –), BATTERY SHEET (LCD) R701 R702 R703 R704 R705 1-216-827-11 1-216-832-11 1-216-835-11 1-216-839-11 1-216-827-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 3.3K 8.2K 15K 33K 3.3K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R706 R707 R708 R709 R710 1-216-832-11 1-216-835-11 1-216-839-11 1-216-827-11 1-216-832-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 8.2K 15K 33K 3.3K 8.2K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W C401 C402 C403 C405 C406 1-135-177-21 1-162-970-11 1-104-848-11 1-110-569-11 1-164-489-11 R711 R712 R713 1-216-835-11 METAL CHIP 1-216-839-11 METAL CHIP 1-216-823-11 METAL CHIP 15K 33K 1.5K 5% 5% 5% 1/16W 1/16W 1/16W C407 C408 C409 1-162-970-11 CERAMIC CHIP 1-162-919-11 CERAMIC CHIP 1-164-160-11 CERAMIC CHIP 3-035-202-01 SHEET (LCD), INSULATING < CAPACITOR > – 57 – TANTALUM CHIP CERAMIC CHIP TANTALUM CHIP TANTALUM CHIP CERAMIC CHIP 1uF 0.01uF 100uF 47uF 0.22uF 20% 10% 20% 20% 10% 20V 25V 4V 6.3V 16V 0.01uF 22PF 20PF 10% 5% 5% 25V 50V 50V LCD Ref. No. Part No. Description Remark C410 C411 1-162-915-11 CERAMIC CHIP 1-162-915-11 CERAMIC CHIP 10PF 10PF 0.5PF 0.5PF 50V 50V C412 C413 C414 C415 C420 1-162-920-11 1-162-920-11 1-164-004-11 1-162-970-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 27PF 27PF 0.1uF 0.01uF 0.1uF 5% 5% 10% 10% 10% 50V 50V 25V 25V 25V C421 C422 C426 C427 C428 1-162-970-11 1-162-970-11 1-162-964-11 1-162-964-11 1-162-964-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.01uF 0.001uF 0.001uF 0.001uF 10% 10% 10% 10% 10% 25V 25V 50V 50V 50V C442 C443 C444 C445 C446 1-135-177-21 1-104-847-11 1-104-848-11 1-162-970-11 1-162-970-11 TANTALUM CHIP TANTALUM CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP 1uF 22uF 100uF 0.01uF 0.01uF 20% 20% 20% 10% 10% 20V 4V 4V 25V 25V C447 C465 C466 C467 C468 1-126-934-11 1-162-964-11 1-162-964-11 1-162-927-11 1-162-927-11 ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 220uF 0.001uF 0.001uF 100PF 100PF 20% 10% 10% 5% 5% 10V 50V 50V 50V 50V C469 C470 C471 C472 C473 1-162-927-11 1-162-919-11 1-162-923-11 1-162-964-11 1-162-970-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 100PF 22PF 47PF 0.001uF 0.01uF 5% 5% 5% 10% 10% 50V 50V 50V 50V 25V C474 C475 C476 C477 C478 1-162-964-11 1-162-964-11 1-162-964-11 1-162-970-11 1-162-970-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 0.001uF 0.01uF 0.01uF 10% 10% 10% 10% 10% 50V 50V 50V 25V 25V C479 C480 C481 C482 C483 1-162-964-11 1-162-964-11 1-162-964-11 1-162-927-11 1-162-964-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.001uF 0.001uF 100PF 0.001uF 10% 10% 10% 5% 10% 50V 50V 50V 50V 50V C484 C485 C486 C487 C488 1-162-927-11 1-162-970-11 1-162-970-11 1-162-970-11 1-162-970-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 100PF 0.01uF 0.01uF 0.01uF 0.01uF 5% 10% 10% 10% 10% 50V 25V 25V 25V 25V C489 C490 C496 1-162-970-11 CERAMIC CHIP 0.01uF 1-104-847-11 TANTALUM CHIP 22uF 1-164-489-11 CERAMIC CHIP 0.22uF 10% 20% 10% 25V 4V 16V Ref. No. Part No. Description D407 D408 D409 D410 8-719-056-07 8-719-056-07 8-719-941-86 8-719-056-76 LED SLR-342MC3F (LCD BACK LIGHT) LED SLR-342MC3F (LCD BACK LIGHT) DIODE DAN202U DIODE UDZ-TE-17-3.6B Remark D411 D412 D413 D417 D419 8-719-988-61 8-719-975-40 8-719-988-61 8-719-976-96 8-719-976-96 DIODE DIODE DIODE DIODE DIODE 1SS355TE-17 RB411D 1SS355TE-17 DTZ4.7C DTZ4.7C D420 D421 D422 D450 D451 8-719-975-40 8-719-988-61 8-719-988-61 8-719-988-61 8-719-988-61 DIODE DIODE DIODE DIODE DIODE RB411D 1SS355TE-17 1SS355TE-17 1SS355TE-17 1SS355TE-17 < IC > IC401 IC402 IC403 8-759-587-66 IC LC867124A-5M74 8-759-426-02 IC RH5RL34AA-T1 8-759-349-55 IC RH5VL25AA-T1 < COIL > L401 L402 L403 L404 L405 1-412-959-11 1-412-959-11 1-412-959-11 1-412-939-11 1-412-959-11 INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR 47uH 47uH 47uH 1uH 47uH < LIQUID CRYSTAL DISPLAY > LCD401 1-803-591-11 DISPLAY PANEL, LIQUID CRYSTAL < TRANSISTOR > Q401 Q402 Q403 Q404 Q405 8-729-907-00 8-729-907-00 8-729-028-73 8-729-028-73 8-729-905-34 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTC114EU DTC114EU DTA114EUA-T106 DTA114EUA-T106 2SC4081-Q Q406 Q407 Q408 Q410 Q411 8-729-028-73 8-729-905-34 8-729-905-34 8-729-028-73 8-729-049-50 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTA114EUA-T106 2SC4081-Q 2SC4081-Q DTA114EUA-T106 2SB1424-T100-R Q412 Q413 Q414 Q415 8-729-032-04 8-729-029-14 8-729-028-91 8-729-028-73 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SD2150-T100QRS DTC144EUA-T106 DTA144EUA-T106 DTA114EUA-T106 < RESISTOR > < CONNECTOR > CN401 * CN403 < DIODE > R401 R402 R403 R404 R405 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W 1-766-613-21 CONNECTOR, FFC/FPC 36P 1-750-898-11 SOCKET, CONNECTOR 5P D401 D402 D403 D404 D405 8-719-975-40 8-719-988-61 8-719-988-61 8-719-988-61 8-719-056-07 DIODE RB411D DIODE 1SS355TE-17 DIODE 1SS355TE-17 DIODE 1SS355TE-17 LED SLR-342MC3F (LCD BACK LIGHT) R406 R407 R408 R409 R410 1-216-809-11 1-216-809-11 1-216-857-11 1-216-809-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 1M 100 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W D406 8-719-056-07 LED SLR-342MC3F (LCD BACK LIGHT) R411 1-216-809-11 METAL CHIP 100 5% 1/16W – 58 – LCD Ref. No. Remark Ref. No. MAIN Part No. Description R471 R472 R473 R474 R475 1-216-864-11 1-216-864-11 1-216-864-11 1-216-833-11 1-216-823-11 METAL CHIP METAL CHIP METAL CHIP RES, CHIP METAL CHIP 0 0 0 10K 1.5K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W Remark R479 R480 R484 R487 R488 1-216-817-11 1-216-853-11 1-216-821-11 1-216-821-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 470 470K 1K 1K 1K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R489 R490 R491 R492 R493 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-021-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 68 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/10W R495 R496 R497 R498 R499 1-216-825-11 1-216-833-11 1-216-833-11 1-216-021-00 1-216-849-11 METAL CHIP RES, CHIP RES, CHIP METAL CHIP METAL CHIP 2.2K 10K 10K 68 220K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/10W 1/16W R750 R751 R754 R755 1-216-857-11 1-216-821-11 1-216-845-11 1-216-841-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1M 1K 100K 47K 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W Part No. Description R412 R413 R414 R415 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W R416 R417 R418 R419 R420 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R421 R422 R424 R426 R427 1-216-809-11 1-216-829-11 1-216-837-11 1-216-298-00 1-216-298-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 4.7K 22K 2.2 2.2 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/10W 1/10W R428 R429 R430 R431 R432 1-216-298-00 1-216-298-00 1-216-021-00 1-216-021-00 1-216-841-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 2.2 2.2 68 68 47K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/16W R433 R434 R435 R436 R437 1-216-841-11 1-218-740-11 1-218-740-11 1-216-845-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES, CHIP 47K 100K 100K 100K 10K 5% 0.5% 0.5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R438 R439 R440 R441 R442 1-216-833-11 1-216-833-11 1-216-829-11 1-216-829-11 1-216-841-11 RES, CHIP RES, CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 4.7K 4.7K 47K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R443 R444 R445 R446 R447 1-216-841-11 1-216-296-00 1-216-851-11 1-216-853-11 1-216-841-11 METAL CHIP SHORT METAL CHIP METAL CHIP METAL CHIP 47K 0 330K 470K 47K 5% 1/16W 5% 5% 5% 1/16W 1/16W 1/16W X401 1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz) X402 1-781-570-21 VIBRATOR, CERAMIC (3MHz) ************************************************************** R448 R449 R450 R451 R452 1-216-841-11 1-216-841-11 1-216-841-11 1-216-827-11 1-216-832-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 47K 47K 47K 3.3K 8.2K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W * * * R453 R454 R457 1-216-853-11 METAL CHIP 1-216-821-11 METAL CHIP 1-216-833-11 RES, CHIP 470K 1K 10K 5% 5% 5% R458 1-216-833-11 RES, CHIP R459 1-216-833-11 RES, CHIP R460 R461 R463 R464 R465 1-216-841-11 1-216-841-11 1-216-833-11 1-216-821-11 1-216-821-11 METAL CHIP METAL CHIP RES, CHIP METAL CHIP METAL CHIP 47K 47K 10K 1K 1K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R466 R467 R468 1-216-821-11 METAL CHIP 1-216-825-11 METAL CHIP 1-216-833-11 RES, CHIP 1K 2.2K 10K 5% 5% 5% R469 R470 1-216-833-11 RES, CHIP 1-216-864-11 METAL CHIP 10K 0 5% 5% 1/16W 1/16W 1/16W (CD2000) 1/16W 1/16W < SWITCH > S401 S402 S403 1-572-050-11 SWITCH, PUSH (1KEY) (OPEN MAIN) 1-692-453-11 SWITCH, KEYBOARD (WORLD/LOCAL) 1-692-453-11 SWITCH, KEYBOARD (D.S.T. SUMMER T.) < VIBRATOR > A-3683-084-A MAIN BOARD, COMPLETE (CD2000: US, CND) A-3683-086-A MAIN BOARD, COMPLETE (CD2000: E, SP, JE) A-3683-102-A MAIN BOARD, COMPLETE (CD2000S) ********************* 3-033-549-01 3-033-563-01 3-033-571-01 3-039-164-01 3-040-409-01 1/16W 1/16W 1/16W (CD2000S) 10K 5% 1/16W (CD2000: E, SP, JE) 10K 5% 1/16W (CD2000: US, CND/CD2000S) CHASSIS TERMINAL BOARD, ANTENNA TERMINAL (+ -), BATTERY SHEET (SHIELD B), INSULATING SHEET (CHASSIS), ELECTROSTATIC 3-040-410-01 CUSHION (SHIELD B) 3-040-780-01 SHEET, ELECTROSTATIC < BAND PASS FILTER > BPF1 BPF1 1-236-053-11 FILTER, BAND PASS (CD2000: US, CND/CD2000S) 1-236-069-21 FILTER, BAND PASS (CD2000: E, SP, JE) < CAPACITOR/RESISTOR > C1 1-162-970-11 CERAMIC CHIP 0.01uF C2 1-216-864-11 METAL CHIP 0 C2 1-162-970-11 CERAMIC CHIP 0.01uF – 59 – 10% 25V (CD2000S) 5% 1/16W (CD2000) 10% 25V (CD2000S) MAIN Ref. No. Part No. Description Remark C3 1-162-970-11 CERAMIC CHIP C4 1-104-847-11 TANTALUM CHIP 22uF C5 1-162-915-11 CERAMIC CHIP 10PF C6 C7 1-162-970-11 CERAMIC CHIP 1-162-920-11 CERAMIC CHIP 0.01uF 27PF C8 1-162-915-11 CERAMIC CHIP 10PF C9 1-162-970-11 CERAMIC CHIP 0.01uF 50V (CD2000S) 10% 25V 5% 50V (CD2000S) 0.5PF 50V (CD2000S) 10% 25V C10 1-162-927-11 CERAMIC CHIP 100PF 5% C11 C12 C13 1-164-227-11 CERAMIC CHIP 1-164-227-11 CERAMIC CHIP 1-162-910-11 CERAMIC CHIP 0.022uF 0.022uF 5PF C13 1-162-915-11 CERAMIC CHIP 10PF C14 1-164-227-11 CERAMIC CHIP 0.022uF C14 1-216-864-11 METAL CHIP 0 C15 1-164-227-11 CERAMIC CHIP 0.022uF C16 1-104-847-11 TANTALUM CHIP 22uF C17 1-164-227-11 CERAMIC CHIP 0.022uF C18 1-162-970-11 CERAMIC CHIP 0.01uF C19 1-164-227-11 CERAMIC CHIP 0.022uF C21 1-216-864-11 METAL CHIP 0 C21 1-162-970-11 CERAMIC CHIP 0.01uF C22 1-164-392-11 CERAMIC CHIP 390PF 25V (CD2000S) 10% 25V (CD2000S) 5% 1/16W (CD2000) 10% 25V (CD2000S) 5% 50V C23 C24 1-162-970-11 CERAMIC CHIP 1-164-227-11 CERAMIC CHIP 0.01uF 0.022uF 10% 10% C25 1-162-970-11 CERAMIC CHIP 0.01uF C26 C27 1-162-910-11 CERAMIC CHIP 1-162-922-11 CERAMIC CHIP 5PF 39PF C28 C29 C30 C31 C32 1-162-964-11 1-164-357-11 1-164-357-11 1-164-357-11 1-162-908-11 0.001uF 1000PF 1000PF 1000PF 5PF C32 1-162-910-11 CERAMIC CHIP C33 C34 C35 C36 1-162-907-11 1-104-847-11 1-164-357-11 1-162-970-11 C39 C40 1-162-927-11 CERAMIC CHIP 1-162-970-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 10% 25V (CD2000S) 20% 4V (CD2000S) 0.5PF 50V (CD2000S) 10% 25V 10% 25V 0.25PF 50V (CD2000) 0.5PF 50V (CD2000S) 25V (CD2000) 5% 1/16W (CD2000S) 10% 25V (CD2000S) 20% 4V (CD2000S) 10% 25V (CD2000S) Part No. Description Remark C41 C42 C43 1-135-177-21 TANTALUM CHIP 1uF 1-135-259-11 TANTALUM CHIP 10uF 1-109-982-11 CERAMIC CHIP 1uF 20% 20% 10% 20V 6.3V 10V C44 C45 C46 C47 C48 1-164-230-11 1-135-259-11 1-165-176-11 1-110-569-11 1-162-970-11 CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP 220PF 10uF 0.047uF 47uF 0.01uF 5% 20% 10% 20% 10% 50V 6.3V 16V 6.3V 25V C49 C50 C51 C52 C53 1-135-177-21 1-162-970-11 1-135-177-21 1-115-416-11 1-164-004-11 TANTALUM CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP 1uF 0.01uF 1uF 1000PF 0.1uF 20% 10% 20% 5% 10% 20V 25V 20V 25V 25V C54 C55 C56 C57 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V 1-135-259-11 TANTALUM CHIP 10uF 20% 6.3V 1-216-864-11 METAL CHIP 0 5% 1/16W (CD2000: US, CND/CD2000S) 1-162-919-11 CERAMIC CHIP 22PF 5% 50V (CD2000: E, SP, JE) 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C59 C60 C71 C72 C73 1-164-004-11 1-162-970-11 1-162-964-11 1-162-970-11 1-162-927-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.01uF 0.001uF 0.01uF 100PF 10% 10% 10% 10% 5% 25V 25V 50V 25V 50V C74 C75 C76 C77 C78 1-162-927-11 1-162-927-11 1-162-927-11 1-110-501-11 1-164-315-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 100PF 100PF 100PF 0.33uF 470PF 5% 5% 5% 10% 5% 50V 50V 50V 16V 50V C79 C80 C81 C82 C83 1-164-230-11 1-162-916-11 1-162-916-11 1-162-970-11 1-162-919-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 220PF 12PF 12PF 0.01uF 22PF 5% 5% 5% 10% 5% 50V 50V 50V 25V 50V C84 C85 C86 C87 C88 1-135-259-11 1-162-970-11 1-135-177-21 1-162-970-11 1-104-847-11 TANTALUM CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP TANTALUM CHIP 10uF 0.01uF 1uF 0.01uF 22uF 20% 10% 20% 10% 20% 6.3V 25V 20V 25V 4V C89 1-164-004-11 CERAMIC CHIP C90 C91 C92 C93 1-162-927-11 1-162-964-11 1-162-908-11 1-162-908-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP C94 C95 C101 C102 C103 1-162-970-11 1-162-970-11 1-163-063-11 1-164-174-11 1-135-177-21 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP 0.01uF 0.01uF 0.022uF 0.0082uF 1uF 10% 10% 10% 10% 20% 25V 25V 50V 25V 20V C104 C105 C106 C111 C112 1-162-964-11 1-104-509-11 1-126-603-11 1-135-210-11 1-162-923-11 CERAMIC CHIP CERAMIC CHIP ELECT CHIP TANTALUM CHIP CERAMIC CHIP 0.001uF 0.018uF 4.7uF 4.7uF 47PF 10% 10% 20% 20% 5% 50V 16V 35V 10V 50V C113 C114 1-162-927-11 CERAMIC CHIP 1-165-176-11 CERAMIC CHIP 100PF 0.047uF 5% 10% 50V 16V C56 10% 10% 25V 25V (CD2000S) 10% 25V (CD2000S) 0.25PF 50V 5% 50V (CD2000S) 10% 50V 5% 50V 5% 50V 5% 50V 0.25PF 50V (CD2000: E, SP, JE) 3PF 0.25PF 50V (CD2000: US, CND/CD2000S) CERAMIC CHIP 2PF 0.25PF 50V TANTALUM CHIP 22uF 20% 4V CERAMIC CHIP 1000PF 5% 50V CERAMIC CHIP 0.01uF 10% 25V 100PF 0.01uF Ref. No. 5% 10% 50V 25V – 60 – 0.1uF 10% 25V (CD2000: E, SP, JE/CD2000S) 100PF 5% 50V 0.001uF 10% 50V 3PF 0.25PF 50V 3PF 0.25PF 50V MAIN Ref. No. Part No. Description Remark C115 C116 C117 1-162-964-11 CERAMIC CHIP 0.001uF 1-135-259-11 TANTALUM CHIP 10uF 1-164-227-11 CERAMIC CHIP 0.022uF 10% 20% 10% 50V 6.3V 25V C118 C119 C120 C123 C124 1-165-176-11 1-164-489-11 1-165-176-11 1-115-467-11 1-115-467-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.047uF 0.22uF 0.047uF 0.22uF 0.22uF 10% 10% 10% 10% 10% 16V 16V 16V 10V 10V C201 C202 C203 C204 C205 1-163-063-11 1-164-174-11 1-135-177-21 1-162-964-11 1-104-509-11 CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP 0.022uF 0.0082uF 1uF 0.001uF 0.018uF 10% 10% 20% 10% 10% 50V 25V 20V 50V 16V C206 C211 C212 C213 C214 1-126-603-11 1-135-210-11 1-162-923-11 1-162-927-11 1-165-176-11 ELECT CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 4.7uF 4.7uF 47PF 100PF 0.047uF 20% 20% 5% 5% 10% 35V 10V 50V 50V 16V C215 C216 C217 C218 C219 1-162-964-11 1-135-259-11 1-164-227-11 1-165-176-11 1-164-489-11 CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 10uF 0.022uF 0.047uF 0.22uF 10% 20% 10% 10% 10% 50V 6.3V 25V 16V 16V C220 C223 C224 C301 C302 1-165-176-11 1-115-467-11 1-115-467-11 1-162-970-11 1-107-823-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.047uF 0.22uF 0.22uF 0.01uF 0.47uF 10% 10% 10% 10% 10% 16V 10V 10V 25V 16V C303 C304 C309 C314 C315 1-110-569-11 1-109-982-11 1-164-004-11 1-162-927-11 1-135-177-21 TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP 47uF 1uF 0.1uF 100PF 1uF 20% 10% 10% 5% 20% 6.3V 10V 25V 50V 20V C316 C317 C318 C319 C320 1-110-569-11 1-164-004-11 1-162-968-11 1-110-569-11 1-164-227-11 TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP 47uF 0.1uF 0.0047uF 47uF 0.022uF 20% 10% 10% 20% 10% 6.3V 25V 50V 6.3V 25V C321 C322 C324 C325 C327 1-162-964-11 1-162-927-11 1-162-970-11 1-162-968-11 1-162-927-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 100PF 0.01uF 0.0047uF 100PF 10% 5% 10% 10% 5% 50V 50V 25V 50V 50V C328 C329 C330 C331 C332 1-107-826-11 1-162-927-11 1-110-569-11 1-110-569-11 1-110-569-11 CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP TANTALUM CHIP TANTALUM CHIP 0.1uF 100PF 47uF 47uF 47uF 10% 5% 20% 20% 20% 16V 50V 6.3V 6.3V 6.3V C333 C334 C335 C337 C338 1-162-970-11 1-128-057-11 1-135-149-21 1-165-176-11 1-165-176-11 CERAMIC CHIP ELECT TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 330uF 2.2uF 0.047uF 0.047uF 10% 20% 20% 10% 10% 25V 6.3V 10V 16V 16V C340 C341 C342 C417 C418 1-135-210-11 1-104-847-11 1-110-569-11 1-162-966-11 1-165-176-11 TANTALUM CHIP TANTALUM CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP 4.7uF 22uF 47uF 0.0022uF 0.047uF 20% 20% 20% 10% 10% 10V 4V 6.3V 50V 16V Ref. No. Part No. Description C419 C493 C494 C495 C502 1-162-970-11 1-162-927-11 1-162-927-11 1-162-927-11 1-110-501-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 100PF 100PF 100PF 0.33uF 10% 5% 5% 5% 10% 25V 50V 50V 50V 16V C503 C504 C505 C506 C507 1-165-176-11 1-162-964-11 1-164-677-11 1-162-969-11 1-110-563-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.047uF 0.001uF 0.033uF 0.0068uF 0.068uF 10% 10% 10% 10% 10% 16V 50V 16V 25V 16V C508 C510 C511 C512 C513 1-110-563-11 1-164-004-11 1-162-965-11 1-110-501-11 1-164-227-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.068uF 0.1uF 0.0015uF 0.33uF 0.022uF 10% 10% 10% 10% 10% 16V 25V 50V 16V 25V C514 C515 C516 C517 C518 1-164-245-11 1-104-847-11 1-107-826-11 1-162-927-11 1-125-817-11 CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.015uF 22uF 0.1uF 100PF 10uF 10% 20% 10% 5% 10% 25V 4V 16V 50V 6.3V C519 C520 C521 C522 C524 1-109-982-11 1-113-988-11 1-162-968-11 1-164-315-11 1-162-968-11 CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1uF 68uF 0.0047uF 470PF 0.0047uF 10% 20% 10% 5% 10% 10V 4V 50V 50V 50V C525 C526 C527 C529 C530 1-162-908-11 1-162-911-11 1-164-004-11 1-135-210-11 1-162-923-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP 3PF 6PF 0.1uF 4.7uF 47PF 0.25PF 0.5PF 10% 20% 5% 50V 50V 25V 10V 50V C531 C532 C533 C534 C535 1-162-923-11 1-162-923-11 1-162-970-11 1-110-569-11 1-110-569-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP TANTALUM CHIP 47PF 47PF 0.01uF 47uF 47uF 5% 5% 10% 20% 20% 50V 50V 25V 6.3V 6.3V C536 C537 C538 C539 C540 1-162-970-11 1-165-176-11 1-165-176-11 1-109-982-11 1-162-970-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.047uF 0.047uF 1uF 0.01uF 10% 10% 10% 10% 10% 25V 16V 16V 10V 25V C541 C542 C543 C544 C545 1-110-569-11 1-162-970-11 1-110-569-11 1-162-970-11 1-165-176-11 TANTALUM CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP 47uF 0.01uF 47uF 0.01uF 0.047uF 20% 10% 20% 10% 10% 6.3V 25V 6.3V 25V 16V C546 C547 C548 C549 C550 1-164-004-11 1-113-988-11 1-162-970-11 1-164-004-11 1-109-982-11 CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 68uF 0.01uF 0.1uF 1uF 10% 20% 10% 10% 10% 25V 4V 25V 25V 10V C551 C552 C553 C554 C555 1-162-970-11 1-164-004-11 1-107-823-11 1-162-970-11 1-164-230-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.1uF 0.47uF 0.01uF 220PF 10% 10% 10% 10% 5% 25V 25V 16V 25V 50V C556 C557 1-135-259-11 TANTALUM CHIP 10uF 1-162-927-11 CERAMIC CHIP 100PF 20% 5% 6.3V 50V – 61 – Remark MAIN Ref. No. Part No. Description Remark C558 C559 C561 1-110-501-11 CERAMIC CHIP 0.33uF 1-164-245-11 CERAMIC CHIP 0.015uF 1-110-569-11 TANTALUM CHIP 47uF 10% 10% 20% 16V 25V 6.3V C562 C564 C565 C566 C568 1-113-988-11 1-113-988-11 1-162-970-11 1-162-970-11 1-113-988-11 TANTALUM CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP 68uF 68uF 0.01uF 0.01uF 68uF 20% 20% 10% 10% 20% 4V 4V 25V 25V 4V C569 C570 C572 C573 C574 1-162-970-11 1-104-847-11 1-125-817-11 1-164-004-11 1-164-489-11 CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 22uF 10uF 0.1uF 0.22uF 10% 20% 10% 10% 10% 25V 4V 6.3V 25V 16V C575 C576 C577 C578 C579 1-135-210-11 1-162-970-11 1-164-230-11 1-164-230-11 1-164-230-11 TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 4.7uF 0.01uF 220PF 220PF 220PF 20% 10% 5% 5% 5% 10V 25V 50V 50V 50V C580 C581 C582 C583 C584 1-164-230-11 1-164-230-11 1-164-230-11 1-164-230-11 1-164-230-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 220PF 220PF 220PF 220PF 220PF 5% 5% 5% 5% 5% 50V 50V 50V 50V 50V C585 C586 C587 C588 C589 1-164-230-11 1-164-230-11 1-164-230-11 1-164-230-11 1-164-230-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 220PF 220PF 220PF 220PF 220PF 5% 5% 5% 5% 5% 50V 50V 50V 50V 50V C590 C591 C592 C593 C594 1-164-230-11 1-164-230-11 1-164-230-11 1-164-230-11 1-164-230-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 220PF 220PF 220PF 220PF 220PF 5% 5% 5% 5% 5% 50V 50V 50V 50V 50V C595 C596 C597 C601 C602 1-104-847-11 1-109-982-11 1-164-315-11 1-113-996-11 1-164-004-11 TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP 22uF 1uF 470PF 220uF 0.1uF 20% 10% 5% 20% 10% 4V 10V 50V 4V 25V C603 C604 C605 C606 C607 1-164-004-11 1-135-210-11 1-164-217-11 1-162-927-11 1-164-004-11 CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 4.7uF 150PF 100PF 0.1uF 10% 20% 5% 5% 10% 25V 10V 50V 50V 25V C608 C609 C610 C611 C612 1-110-569-11 1-162-970-11 1-110-569-11 1-162-965-11 1-164-489-11 TANTALUM CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP 47uF 0.01uF 47uF 0.0015uF 0.22uF 20% 10% 20% 10% 10% 6.3V 25V 6.3V 50V 16V C613 C614 C615 C616 C617 1-113-996-11 1-162-970-11 1-164-004-11 1-164-004-11 1-164-004-11 TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 220uF 0.01uF 0.1uF 0.1uF 0.1uF 20% 10% 10% 10% 10% 4V 25V 25V 25V 25V C618 C619 C620 C621 C622 1-164-004-11 1-162-964-11 1-135-210-11 1-162-970-11 1-164-004-11 CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.001uF 4.7uF 0.01uF 0.1uF 10% 10% 20% 10% 10% 25V 50V 10V 25V 25V Ref. No. Part No. Description Remark C623 C625 C626 C627 C628 1-135-210-11 1-162-927-11 1-135-210-11 1-164-227-11 1-164-227-11 TANTALUM CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP 4.7uF 100PF 4.7uF 0.022uF 0.022uF 20% 5% 20% 10% 10% 10V 50V 10V 25V 25V C629 C801 C802 C803 C804 1-104-847-11 1-110-501-11 1-164-230-11 1-164-004-11 1-109-982-11 TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 22uF 0.33uF 220PF 0.1uF 1uF 20% 10% 5% 10% 10% 4V 16V 50V 25V 10V C805 C806 C807 C810 C811 1-162-970-11 1-162-970-11 1-162-970-11 1-165-176-11 1-113-988-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP 0.01uF 0.01uF 0.01uF 0.047uF 68uF 10% 10% 10% 10% 20% 25V 25V 25V 16V 4V C901 C902 C904 C905 C906 1-128-394-11 1-128-394-11 1-110-569-11 1-128-394-11 1-128-391-11 ELECT CHIP ELECT CHIP TANTALUM CHIP ELECT CHIP ELECT CHIP 220uF 220uF 47uF 220uF 330uF 20% 20% 20% 20% 20% 10V 10V 6.3V 10V 6.3V C907 C908 1-126-518-11 ELECT 1-162-970-11 CERAMIC CHIP 470uF 0.01uF 20% 10% 4V 25V < FILTER > CF1 CF2 CF3 1-781-419-71 FILTER, CERAMIC (DISCRIMINATOR) (10.7MHz) 1-767-480-11 FILTER, CERAMIC (AM) (450kHz) 1-767-313-11 FILTER, CERAMIC (10.7MHz) < CONNECTOR > CN301 CN501 CN601 CN602 CN603 1-766-614-21 1-779-761-21 1-784-342-21 1-784-342-31 1-784-342-11 CONNECTOR, FFC/FPC 36P CONNECTOR, FPC (ZIF) HOUSING, CONNECTOR 2P HOUSING, CONNECTOR 2P HOUSING, CONNECTOR 2P < TRIMMER > CT1 CT2 CT3 1-141-327-11 CAP, CHIP TYPE TRIMMER 10PF (CD2000S) 1-141-327-11 CAP, CHIP TYPE TRIMMER 10PF 1-141-327-11 CAP, CHIP TYPE TRIMMER 10PF < DIODE/SHORT > D1 D3 D3 D5 D5 8-719-800-76 1-216-295-00 8-719-038-20 1-216-295-00 8-719-044-76 DIODE 1SS226 SHORT 0 (CD2000) DIODE 1SS314 (CD2000S) SHORT 0 (CD2000) DIODE 1SS356-TW11 (CD2000S) D6 D8 D9 D10 D12 8-719-044-76 8-719-072-58 8-719-072-58 8-719-072-58 8-713-100-11 DIODE DIODE DIODE DIODE DIODE 1SS356-TW11 (CD2000S) SVC347-TL (CD2000S) SVC347-TL SVC347-TL (CD2000S) 1T362 (CD2000: US, CND/CD2000S) D12 D13 D13 D14 D70 8-719-002-81 8-713-100-11 8-719-002-81 8-719-988-61 8-719-977-40 DIODE DIODE DIODE DIODE DIODE 1T363 (CD2000: E, SP, JE) 1T362 (CD2000: US, CND/CD2000S) 1T363 (CD2000: E, SP, JE) 1SS355TE-17 DTZ-TT11-13 – 62 – MAIN Ref. No. Remark Ref. No. Part No. Description Remark Part No. Description D71 D101 D102 D103 D104 8-719-988-61 8-719-800-76 8-719-941-86 8-719-800-76 8-719-988-61 DIODE DIODE DIODE DIODE DIODE 1SS355TE-17 1SS226 DAN202U 1SS226 1SS355TE-17 D201 D202 D203 D204 D301 8-719-800-76 8-719-941-86 8-719-800-76 8-719-988-61 8-719-056-76 DIODE DIODE DIODE DIODE DIODE 1SS226 DAN202U 1SS226 1SS355TE-17 UDZ-TE-17-3.6B D304 D307 D308 D423 D424 8-719-941-86 8-719-800-76 8-719-941-86 8-719-941-86 8-719-941-86 DIODE DIODE DIODE DIODE DIODE DAN202U 1SS226 DAN202U DAN202U DAN202U J301 D425 D426 D427 D428 D429 8-719-941-86 8-719-941-86 8-719-941-86 8-719-941-86 8-719-941-86 DIODE DIODE DIODE DIODE DIODE DAN202U DAN202U DAN202U DAN202U DAN202U L2 L3 L4 L5 L7 1-412-951-11 1-412-951-11 1-412-935-11 1-410-658-31 1-754-065-11 INDUCTOR 10uH (CD2000S) INDUCTOR 10uH (CD2000S) INDUCTOR 0.47uH (CD2000S) INDUCTOR CHIP 220uH (CD2000S) ANTENNA, FERRITE-ROD (AM (MW)) D430 D433 D434 D501 D502 8-719-988-61 8-719-941-86 8-719-941-86 8-719-988-61 8-719-988-61 DIODE DIODE DIODE DIODE DIODE 1SS355TE-17 DAN202U DAN202U 1SS355TE-17 1SS355TE-17 L8 L10 L11 L12 L13 1-419-137-21 1-410-658-31 1-412-947-11 1-419-137-21 1-419-262-21 COIL (SW ANTENNA) (CD2000S) INDUCTOR CHIP 220uH (CD2000S) INDUCTOR 4.7uH (CD2000S) COIL (SW OSC) (CD2000S) COIL (AM (MW) OSC) D503 D504 D512 D514 D601 8-719-941-86 8-719-941-86 8-719-988-61 8-719-941-86 8-719-975-40 DIODE DIODE DIODE DIODE DIODE DAN202U DAN202U 1SS355TE-17 DAN202U RB411D L14 L14 L15 L15 L17 1-419-261-11 COIL, AIR-CORE (CD2000: US, CND/CD2000S) 1-419-324-11 COIL, AIR-CORE (CD2000: E, SP, JE) 1-414-691-21 INDUCTOR 100nH (CD2000: US, CND/CD2000S) 1-414-693-11 INDUCTOR 150nH (CD2000: E, SP, JE) 1-412-951-11 INDUCTOR 10uH D602 D901 D903 D904 D905 8-719-975-40 8-719-941-86 8-719-974-51 8-719-941-86 8-719-941-86 DIODE DIODE DIODE DIODE DIODE RB411D DAN202U SB20-03P DAN202U DAN202U L18 L19 L20 L70 L72 1-412-951-11 1-412-937-11 1-412-959-11 1-412-951-11 1-412-951-11 INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR 10uH 0.68uH (CD2000: E, SP, JE) 47uH 10uH 10uH L73 L74 L301 L501 L502 1-412-959-11 1-412-939-11 1-412-951-11 1-412-947-11 1-412-006-31 INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR CHIP 47uH 1uH 10uH 4.7uH 10uH L504 L505 L508 L509 L511 1-412-951-11 1-412-002-31 1-412-959-11 1-412-959-11 1-412-959-11 INDUCTOR INDUCTOR CHIP INDUCTOR INDUCTOR INDUCTOR 10uH 4.7uH 47uH 47uH 47uH < IC > L512 L513 L514 L515 L516 1-412-959-11 1-412-959-11 1-412-060-11 1-412-060-11 1-412-060-11 INDUCTOR INDUCTOR INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP 47uH 47uH 22uH 22uH 22uH IC IC IC IC IC INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR 47uH 47uH 47uH 47uH 47uH IC303 IC404 IC501 8-759-338-78 IC BA10324AFV-E2 8-759-529-76 IC TC74VHC595FT (EL) 8-759-589-95 IC LA9251M-MPB IC502 IC503 IC505 IC506 IC601 8-759-590-49 8-759-498-44 8-759-387-31 8-759-366-35 8-759-589-96 IC901 8-759-493-39 IC RN5RZ33BA-TR IC IC IC IC IC LC78626KE MSM51V4400D-70TSK TC75S55F (TE85R) TC4W66F (TE12R) LB8118M < JACK > 1-778-034-11 JACK (i) < COIL > < FERRITE BEAD > FB1 FB2 FB3 FB101 FB102 1-543-963-22 1-543-963-22 1-543-963-22 1-543-963-22 1-543-963-22 FERRITE FERRITE FERRITE FERRITE FERRITE 0uH 0uH 0uH 0uH 0uH FB201 FB202 FB301 FB302 FB303 1-543-963-22 1-543-963-22 1-543-963-22 1-543-963-22 1-543-963-22 FERRITE FERRITE FERRITE FERRITE FERRITE 0uH 0uH 0uH 0uH 0uH FB304 FB401 1-543-963-22 FERRITE 1-500-245-11 FERRITE 0uH 0uH IC1 IC2 IC3 IC101 IC201 8-752-065-30 8-759-804-98 8-759-483-40 8-759-702-02 8-759-702-02 CXA1111N LA3335M LC72137M-TLM NJM062M NJM062M L601 L602 L603 L604 L605 1-409-556-11 1-409-556-11 1-411-939-11 1-412-959-11 1-409-556-11 IC301 IC302 8-759-338-78 IC BA10324AFV-E2 8-759-338-78 IC BA10324AFV-E2 L606 L607 1-410-389-31 INDUCTOR CHIP 47uH 1-412-951-11 INDUCTOR 10uH – 63 – MAIN Ref. No. Part No. Description Remark L608 L609 L902 1-412-951-11 INDUCTOR 1-412-959-11 INDUCTOR 1-412-963-11 INDUCTOR 10uH 47uH 100uH L903 1-409-893-21 INDUCTOR 100uH < TRANSISTOR > Q1 Q2 Q3 Q4 Q5 8-729-123-86 8-729-048-85 8-729-123-86 8-729-028-74 8-729-423-52 FET 2SK238-K16 (CD2000S) TRANSISTOR IMD3A-T108 (CD2000S) FET 2SK238-K16 (CD2000S) TRANSISTOR DTA114TUA-T106 (CD2000S) TRANSISTOR 2SC3931-C (CD2000S) Q6 Q8 Q9 Q10 Q11 8-729-402-55 8-729-402-55 8-729-907-00 8-729-048-85 8-729-907-00 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SB1218A-R (CD2000S) 2SB1218A-R (CD2000S) DTC114EU IMD3A-T108 DTC114EU Q74 Q75 Q76 Q101 Q102 8-729-905-34 8-729-905-34 8-729-423-52 8-729-048-84 8-729-029-10 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SC4081-Q 2SC4081-Q 2SC3931-C IMH4A-T110 DTC143TUA-T106 Q103 Q104 Q201 Q202 Q203 8-729-029-10 8-729-029-10 8-729-048-84 8-729-029-10 8-729-029-10 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTC143TUA-T106 DTC143TUA-T106 IMH4A-T110 DTC143TUA-T106 DTC143TUA-T106 Q204 Q301 Q305 Q308 Q309 8-729-029-10 8-729-026-53 8-729-048-84 8-729-907-00 8-729-048-85 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTC143TUA-T106 2SA1576A-T106-QR IMH4A-T110 DTC114EU IMD3A-T108 Q310 Q311 Q312 Q501 Q502 8-729-029-14 8-729-048-84 8-729-028-97 8-729-048-84 8-729-048-84 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR Q503 Q504 Q505 Q506 Q507 8-729-048-84 8-729-907-00 8-729-028-97 8-729-028-74 8-729-028-74 Q509 Q511 Q512 Q513 Q514 Ref. No. Part No. Description Q905 Q906 Q907 Q908 8-729-026-53 8-729-026-53 8-729-921-93 8-729-905-34 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SA1576A-T106-QR 2SA1576A-T106-QR 2SB1182F5-QR 2SC4081-Q Remark Q909 Q910 Q912 Q913 Q914 8-729-028-73 8-729-048-85 8-729-907-00 8-729-907-00 8-729-905-34 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTA114EUA-T106 IMD3A-T108 DTC114EU DTC114EU 2SC4081-Q < RESISTOR > R1 1-216-857-11 METAL CHIP 1M 5% R2 1-216-821-11 METAL CHIP 1K 5% R3 1-216-864-11 METAL CHIP 0 5% R4 1-216-809-11 METAL CHIP 100 5% R5 1-216-815-11 METAL CHIP 330 5% R6 R7 1-216-857-11 METAL CHIP 1-216-864-11 METAL CHIP 1M 0 5% 5% R8 1-216-829-11 METAL CHIP 4.7K 5% R9 1-216-857-11 METAL CHIP 1M 5% R10 1-216-833-11 RES, CHIP 10K 5% R11 1-216-857-11 METAL CHIP 1M 5% R12 1-216-813-11 METAL CHIP 220 5% DTC144EUA-T106 IMH4A-T110 DTC114TUA-T106 IMH4A-T110 IMH4A-T110 R13 1-216-809-11 METAL CHIP 100 5% R14 R15 1-216-833-11 RES, CHIP 1-216-833-11 RES, CHIP 10K 10K 5% 5% TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR IMH4A-T110 DTC114EU DTC114TUA-T106 DTA114TUA-T106 DTA114TUA-T106 R16 1-216-857-11 METAL CHIP 1M 5% R17 1-216-821-11 METAL CHIP 1K 5% R18 1-216-837-11 METAL CHIP 22K 5% 8-729-048-84 8-729-048-85 8-729-028-74 8-729-048-84 8-729-028-74 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR IMH4A-T110 IMD3A-T108 DTA114TUA-T106 IMH4A-T110 DTA114TUA-T106 R19 R20 1-216-857-11 METAL CHIP 1-216-845-11 METAL CHIP 1M 100K 5% 5% R21 R23 R24 1-216-845-11 METAL CHIP 1-216-809-11 METAL CHIP 1-216-816-11 METAL CHIP 100K 100 390 5% 5% 5% Q601 Q602 Q603 Q604 Q605 8-729-402-55 8-729-032-04 8-719-074-91 8-729-049-50 8-729-905-34 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SB1218A-R 2SD2150-T100QRS FX802-TL 2SB1424-T100-R 2SC4081-Q R25 1-216-829-11 METAL CHIP 4.7K 5% R26 1-216-809-11 METAL CHIP 100 5% Q606 Q607 Q608 Q609 Q610 8-729-032-04 8-719-074-91 8-719-074-91 8-729-905-34 8-729-907-00 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SD2150-T100QRS FX802-TL FX802-TL 2SC4081-Q DTC114EU R27 R28 R29 R30 R32 1-216-825-11 1-216-815-11 1-216-821-11 1-216-821-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES, CHIP 2.2K 330 1K 1K 10K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W Q904 8-729-048-85 TRANSISTOR IMD3A-T108 R33 1-216-845-11 METAL CHIP 100K 5% 1/16W – 64 – 1/16W (CD2000S) 1/16W (CD2000S) 1/16W (CD2000S) 1/16W (CD2000S) 1/16W (CD2000S) 1/16W 1/16W (CD2000) 1/16W (CD2000S) 1/16W (CD2000S) 1/16W (CD2000S) 1/16W (CD2000S) 1/16W (CD2000S) 1/16W (CD2000S) 1/16W 1/16W (CD2000S) 1/16W (CD2000S) 1/16W (CD2000S) 1/16W (CD2000S) 1/16W 1/16W 1/16W 1/16W 1/16W (CD2000S) 1/16W (CD2000S) 1/16W (CD2000S) MAIN Part No. Description 27K 10 1K 47K 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W (CD2000S) R115 R116 R117 R118 R119 1-216-821-11 1-216-809-11 1-216-833-11 1-216-841-11 1-216-841-11 METAL CHIP METAL CHIP RES, CHIP METAL CHIP METAL CHIP 1K 100 10K 47K 47K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W 1-216-833-11 RES, CHIP 10K 5% R39 R40 R41 1-216-821-11 METAL CHIP 1-216-829-11 METAL CHIP 1-216-833-11 RES, CHIP 1K 4.7K 10K 5% 5% 5% R120 R121 R123 R124 R125 1-216-833-11 1-216-853-11 1-216-849-11 1-216-841-11 1-216-809-11 RES, CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 470K 220K 47K 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R42 1-216-864-11 METAL CHIP 0 5% 1/16W (CD2000S) 1/16W 1/16W 1/16W (CD2000S) 1/16W (CD2000) R43 1-216-864-11 METAL CHIP 0 5% R126 R127 R128 R129 R130 1-216-833-11 1-216-833-11 1-216-833-11 1-216-298-00 1-216-841-11 RES, CHIP RES, CHIP RES, CHIP METAL CHIP METAL CHIP 10K 10K 10K 2.2 47K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/10W 1/16W R44 R45 R53 1-216-845-11 METAL CHIP 1-216-845-11 METAL CHIP 1-216-809-11 METAL CHIP R53 1-216-864-11 METAL CHIP R133 R134 R201 R202 R203 1-216-835-11 1-216-821-11 1-216-821-11 1-216-847-11 1-216-844-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 15K 1K 1K 150K 82K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R70 R71 R74 R75 1-216-839-11 1-216-833-11 1-216-821-11 1-216-821-11 METAL CHIP RES, CHIP METAL CHIP METAL CHIP 33K 10K 1K 1K 5% 5% 5% 5% R204 R205 R206 R207 R208 1-216-841-11 1-216-847-11 1-216-841-11 1-216-837-11 1-216-834-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 47K 150K 47K 22K 12K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R77 1-216-809-11 METAL CHIP 100 5% 1/16W 1/16W 1/16W 1/16W (CD2000S) 1/16W R78 R79 R80 R81 R82 1-216-809-11 1-216-809-11 1-216-809-11 1-216-833-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP RES, CHIP RES, CHIP 100 100 100 10K 10K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R209 R210 R211 R212 R213 1-216-838-11 1-216-833-11 1-216-829-11 1-216-833-11 1-216-849-11 METAL CHIP RES, CHIP METAL CHIP RES, CHIP METAL CHIP 27K 10K 4.7K 10K 220K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R83 R84 R85 R87 R88 1-216-829-11 1-216-829-11 1-216-829-11 1-216-845-11 1-216-797-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 4.7K 4.7K 4.7K 100K 10 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R215 R216 R217 R218 R219 1-216-821-11 1-216-809-11 1-216-833-11 1-216-841-11 1-216-841-11 METAL CHIP METAL CHIP RES, CHIP METAL CHIP METAL CHIP 1K 100 10K 47K 47K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R89 R90 R91 R92 R93 1-216-845-11 1-216-841-11 1-216-845-11 1-216-821-11 1-216-829-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 47K 100K 1K 4.7K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R220 R221 R222 R223 R224 1-216-833-11 1-216-850-11 1-216-853-11 1-216-849-11 1-216-841-11 RES, CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 270K 470K 220K 47K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R82 1-216-025-00 RES, CHIP R95 1-216-295-00 SHORT R225 R226 R227 R228 R229 1-216-809-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-298-00 METAL CHIP RES, CHIP RES, CHIP RES, CHIP METAL CHIP 100 10K 10K 10K 2.2 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/10W R101 R102 R103 1-216-821-11 METAL CHIP 1-216-847-11 METAL CHIP 1-216-844-11 METAL CHIP R104 R105 R106 R107 R108 1-216-841-11 1-216-847-11 1-216-841-11 1-216-837-11 1-216-834-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 47K 150K 47K 22K 12K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R230 R233 R234 R301 R302 1-216-841-11 1-216-835-11 1-216-821-11 1-216-833-11 1-216-841-11 METAL CHIP METAL CHIP METAL CHIP RES, CHIP METAL CHIP 47K 15K 1K 10K 47K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R109 R110 R111 R112 R113 1-216-838-11 1-216-833-11 1-216-829-11 1-216-833-11 1-216-849-11 METAL CHIP RES, CHIP METAL CHIP RES, CHIP METAL CHIP 27K 10K 4.7K 10K 220K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R303 R304 R305 R306 R307 1-216-821-11 1-216-833-11 1-216-851-11 1-216-853-11 1-216-845-11 METAL CHIP RES, CHIP METAL CHIP METAL CHIP METAL CHIP 1K 10K 330K 470K 100K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R308 R309 R310 1-216-833-11 RES, CHIP 1-216-837-11 METAL CHIP 1-216-833-11 RES, CHIP 10K 22K 10K 5% 5% 5% 1/16W 1/16W 1/16W Ref. No. Part No. Description R34 R35 R36 R37 1-216-838-11 1-216-797-11 1-216-821-11 1-216-841-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP R38 Remark 1/16W (CD2000) 100K 5% 1/16W 100K 5% 1/16W 100 5% 1/16W (CD2000: US, CND) 0 5% 1/16W (CD2000: E, SP, JE/CD2000S) 100 5% 1/16W (CD2000: US, CND) 0 (CD2000: E, SP, JE/CD2000S) 1K 5% 1/16W 150K 5% 1/16W 82K 5% 1/16W Ref. No. – 65 – Remark MAIN Ref. No. Part No. Description Remark R311 R315 1-216-821-11 METAL CHIP 1-216-845-11 METAL CHIP 1K 100K 5% 5% 1/16W 1/16W R316 R317 R318 R319 R321 1-216-845-11 1-216-821-11 1-216-833-11 1-216-837-11 1-216-825-11 METAL CHIP RES, CHIP RES, CHIP METAL CHIP METAL CHIP 100K 1K 10K 22K 2.2K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R322 R330 R334 R335 R336 1-216-821-11 1-216-837-11 1-216-833-11 1-216-833-11 1-216-853-11 METAL CHIP METAL CHIP RES, CHIP RES, CHIP METAL CHIP 1K 22K 10K 10K 470K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R338 R339 R340 R341 R342 1-216-809-11 1-216-821-11 1-216-837-11 1-216-849-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 1K 22K 220K 1K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R343 R344 R345 R346 R347 1-216-837-11 1-216-844-11 1-216-833-11 1-216-833-11 1-216-841-11 METAL CHIP METAL CHIP RES, CHIP RES, CHIP METAL CHIP 22K 82K 10K 10K 47K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R348 R349 R350 R351 R352 1-216-815-11 1-216-833-11 1-216-845-11 1-216-845-11 1-216-845-11 METAL CHIP RES, CHIP METAL CHIP METAL CHIP METAL CHIP 330 10K 100K 100K 100K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R353 R355 R356 R357 R358 1-216-845-11 1-216-845-11 1-216-811-11 1-216-833-11 1-216-829-11 METAL CHIP METAL CHIP METAL CHIP RES, CHIP METAL CHIP 100K 100K 150 10K 4.7K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R359 R360 R361 R423 R455 1-216-864-11 1-216-841-11 1-216-836-11 1-216-835-11 1-216-841-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 0 47K 18K 15K 47K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R476 R477 R478 R481 R482 1-216-809-11 1-216-809-11 1-216-809-11 1-216-839-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 33K 1K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R483 R486 R501 R503 R504 1-216-833-11 1-216-845-11 1-216-821-11 1-218-732-11 1-216-847-11 RES, CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 100K 1K 47K 150K 5% 5% 5% 0.5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R505 R506 R507 R508 R509 1-216-821-11 1-218-676-11 1-218-740-11 1-218-740-11 1-218-720-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 220 100K 100K 15K 5% 0.5% 0.5% 0.5% 0.5% 1/16W 1/16W 1/16W 1/16W 1/16W R511 R512 R513 R514 R515 1-218-720-11 1-218-734-11 1-216-833-11 1-218-720-11 1-216-841-11 METAL CHIP METAL CHIP RES, CHIP METAL CHIP METAL CHIP 15K 56K 10K 15K 47K 0.5% 0.5% 5% 0.5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W Ref. No. Part No. Description R516 R517 R518 R519 R520 1-216-825-11 1-218-732-11 1-218-720-11 1-218-732-11 1-218-720-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 2.2K 47K 15K 47K 15K 5% 0.5% 0.5% 0.5% 0.5% 1/16W 1/16W 1/16W 1/16W 1/16W R521 R522 R523 R524 R525 1-218-728-11 1-218-676-11 1-218-728-11 1-216-847-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 33K 220 33K 150K 1K 0.5% 0.5% 0.5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R526 R527 R528 R529 R530 1-216-850-11 1-216-850-11 1-216-864-11 1-216-839-11 1-216-829-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 270K 270K 0 33K 4.7K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R531 R532 R533 R535 R536 1-216-830-11 1-218-720-11 1-218-724-11 1-216-854-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES, CHIP 5.6K 15K 22K 560K 10K 5% 0.5% 0.5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R537 R538 R539 R540 R541 1-216-833-11 1-216-833-11 1-216-047-00 1-218-720-11 1-216-822-11 RES, CHIP RES, CHIP RES, CHIP METAL CHIP METAL CHIP 10K 10K 820 15K 1.2K 5% 5% 5% 0.5% 5% 1/16W 1/16W 1/10W 1/16W 1/16W R545 R546 R547 R549 R550 1-216-817-11 1-216-833-11 1-216-829-11 1-216-852-11 1-216-846-11 METAL CHIP RES, CHIP METAL CHIP METAL CHIP METAL CHIP 470 10K 4.7K 390K 120K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R551 R552 R553 R554 R557 1-216-846-11 1-216-846-11 1-216-846-11 1-216-829-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 120K 120K 120K 4.7K 100K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R558 R559 R560 R561 R562 1-216-841-11 1-216-842-11 1-216-833-11 1-216-837-11 1-216-837-11 METAL CHIP METAL CHIP RES, CHIP METAL CHIP METAL CHIP 47K 56K 10K 22K 22K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R563 R564 R565 R566 R567 1-216-825-11 1-216-843-11 1-216-994-11 1-216-825-11 1-218-746-11 METAL CHIP METAL CHIP RES, CHIP METAL CHIP METAL CHIP 2.2K 68K 13K 2.2K 180K 5% 5% 5% 5% 0.5% 1/16W 1/16W 1/16W 1/16W 1/16W R568 R569 R570 R571 R573 1-216-845-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-846-11 METAL CHIP RES, CHIP RES, CHIP RES, CHIP METAL CHIP 100K 10K 10K 10K 120K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R574 R575 R576 R577 R582 1-216-846-11 1-216-833-11 1-216-833-11 1-216-821-11 1-216-864-11 METAL CHIP RES, CHIP RES, CHIP METAL CHIP METAL CHIP 120K 10K 10K 1K 0 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R584 R586 R588 1-216-833-11 RES, CHIP 1-216-825-11 METAL CHIP 1-216-849-11 METAL CHIP 10K 2.2K 220K 5% 5% 5% 1/16W 1/16W 1/16W – 66 – Remark MAIN Ref. No. Part No. Description Remark R591 R592 1-216-841-11 METAL CHIP 1-216-835-11 METAL CHIP 47K 15K 5% 5% 1/16W 1/16W R593 R594 R596 R597 R598 1-216-829-11 1-216-845-11 1-216-833-11 1-216-813-11 1-216-813-11 METAL CHIP METAL CHIP RES, CHIP METAL CHIP METAL CHIP 4.7K 100K 10K 220 220 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R599 R601 R602 R605 R608 1-216-829-11 1-216-841-11 1-216-809-11 1-216-839-11 1-218-292-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES, CHIP 4.7K 47K 100 33K 20K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R615 R616 R623 R624 R625 1-216-845-11 1-216-849-11 1-216-821-11 1-216-837-11 1-216-841-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 220K 1K 22K 47K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R626 R627 R628 R629 R630 1-216-827-11 1-216-820-11 1-218-292-11 1-216-830-11 1-216-834-11 METAL CHIP METAL CHIP RES, CHIP METAL CHIP METAL CHIP 3.3K 820 20K 5.6K 12K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R631 R632 R634 R635 R636 1-216-821-11 1-216-298-00 1-216-821-11 1-216-833-11 1-216-841-11 METAL CHIP METAL CHIP METAL CHIP RES, CHIP METAL CHIP 1K 2.2 1K 10K 47K 5% 5% 5% 5% 5% 1/16W 1/10W 1/16W 1/16W 1/16W R637 R638 R639 R640 R641 1-216-304-11 1-216-304-11 1-216-304-11 1-216-304-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES, CHIP 3.3 3.3 3.3 3.3 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/16W R801 R803 R817 R818 R819 1-216-813-11 1-216-864-11 1-216-821-11 1-216-821-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 220 0 1K 1K 1K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R820 R821 R823 R824 R825 1-216-821-11 1-216-813-11 1-216-817-11 1-216-817-11 1-216-817-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 220 470 470 470 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R826 R827 R828 R829 R830 1-216-817-11 1-216-817-11 1-216-817-11 1-216-821-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 470 470 470 1K 1K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R831 R832 R833 R834 R835 1-216-821-11 1-216-817-11 1-216-821-11 1-216-817-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 470 1K 470 1K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R836 R844 R846 R850 R851 1-216-821-11 1-216-841-11 1-216-864-11 1-216-845-11 1-216-825-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 47K 0 100K 2.2K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W Ref. No. Part No. Description R852 R853 R854 R905 R908 1-216-841-11 1-216-821-11 1-216-837-11 1-216-829-11 1-216-829-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 47K 1K 22K 4.7K 4.7K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W Remark R909 R910 R911 R912 R913 1-216-841-11 1-216-841-11 1-216-821-11 1-216-841-11 1-216-047-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES, CHIP 47K 47K 1K 47K 820 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/10W R914 R915 R916 1-216-841-11 METAL CHIP 1-216-821-11 METAL CHIP 1-216-821-11 METAL CHIP 47K 1K 1K 5% 5% 5% 1/16W 1/16W 1/16W < VARIABLE RESISTOR > RV1 RV2 RV301 1-223-586-11 RES, ADJ, CARBON 10K 1-223-587-11 RES, ADJ, CARBON 22K 1-225-278-21 RES, VAR, CARBON 20K/20K (VOLUME w) < SWITCH > S301 S421 S422 S423 S424 1-571-674-11 1-572-499-21 1-572-499-21 1-692-366-11 1-572-499-21 SWITCH, SLIDE (MEGA BASS) SWITCH, TACTIL (ESP) SWITCH, TACTIL (CD PLAY MODE) SWITCH, PUSH (1KEY) (Z OPEN) SWITCH, TACTIL (CLOCK) < TRANSFORMER > T1 T70 1-435-092-21 TRANSFORMER, IF 1-435-093-21 TRANSFORMER, DC/DC CONVERTER < VIBRATOR > X1 1-767-517-11 VIBRATOR, CRYSTAL (75kHz) X501 1-767-511-11 VIBRATOR, CERAMIC (16.9344MHz) ************************************************************** MISCELLANEOUS ************** 65 72 154 159 0 160 ANT1 L7 LCD401 M601 M602 1-791-188-11 WIRE (FLAT TYPE) (5 CORE) (CD2000: US, CND/CD2000S) 1-791-189-11 WIRE (FLAT TYPE) (36 CORE) (CD2000: US, CND/CD2000S) 1-783-093-11 LEAD (WITH CONNECTOR) 1-667-512-11 SLIDE FLEXIBLE BOARD X-4950-476-1 OPTICAL PICK-UP (DAX-11E) 1-501-222-71 1-754-065-11 1-803-591-11 A-3328-100-A A-3320-642-A ANTENNA, TELESCOPIC (FM) ANTENNA, FERRITE-ROD (MW) DISPLAY PANEL, LIQUID CRYSTAL MOTOR ASSY, SLED MOTOR ASSY, TURN TABLE (SPINDLE) S603 1-571-099-21 SWITCH (1 KEY) (LIMIT) SP101 1-505-311-11 SPEAKER (4cm) SP201 1-505-311-11 SPEAKER (4cm) ************************************************************** – 67 – ICF-CD2000/CD2000S Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark ACCESSORIESS & PACKING MATERIALS ********************************* 1-418-411-11 1-418-412-11 1-418-413-11 1-505-521-11 1-569-007-11 ADAPTOR, AC (AC-E6TR1) (US, CND) ADAPTOR, AC (AC-E6TR1) (AEP, SP) ADAPTOR, AC (AC-E6TR1) (JEW) HEADPHONE (MDR-023) (US) ADAPTOR, CONVERSION 2P (JEW) 3-865-826-11 MANUAL, INSTRUCTION (JAPANESE, ENGLISH, CHINESE, KOREAN) (E, SP, JEW) 3-865-826-21 MANUAL, INSTRUCTION (ENGLISH) (US) 3-865-826-31 MANUAL, INSTRUCTION (ENGLISH, FRENCH, GERMAN, DUTCH) (CND) 3-865-826-41 MANUAL, INSTRUCTION (ENGLISH, ITALIAN, DUTCH, PORTUGUESE) (AEP, E) 3-865-826-51 MANUAL, INSTRUCTION (ENGLISH, SWEDISH, DANISH, FINNISH) (AEP) 8-953-130-90 HEADPHONE MDR-E805LP (CD2000: CND, E, SP, JEW/CD2000S) X-3329-657-1 ATTACHMENT (JEW) The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Sony Corporation 9-927-171-11 Personal Audio Company – 68 – Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le neméro spécifié. 99J0581-1 Printed in Japan C 1999. 10 Published by General Engineering Dept.
Similar documents
ICF-CD873 - Electronica.ro
DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
More informationJE320 - Minidisc.org
circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering.
More informationTM- 271A 271E
CN2 (data terminal) is the data communications terminal on the TX/RX PCB. It handles transmission control, data input/output, and squelch signals. There are two data communications modes : 9600bps ...
More informationservice manual - Philips Parts and Accessories
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
More informationSony - ICF-SW7600GR service manual
4-4. Schematic Diagram – Main Board (1/2) – ··················· 12 4-5. Schematic Diagram – Main Board (2/2) – ··················· 13 4-6. Printed Wiring Board – KEY Board – ·······················...
More informationICF-CDK70 - Panasonic Parts and Accessories
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
More information