ICF-CDK70 - Panasonic Parts and Accessories

ICF-CDK70
SERVICE MANUAL
US Model
Canadian Model
Ver. 1.1 2007.02
Model Name Using Similar Mechanism
HCD-EC50
CD Mechanism Type
DLM3A23-11
Optical Pick-up Block
KSM-213CCP
SPECIFICATIONS
CD player section
General
System: Compact disc digital audio system
Laser diode properties:
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of
about 200 mm from the objective lens surface on
an optical pick-up block with 7 mm aperture.)
Number of channels: 2
Frequency response: 20 – 20 000 Hz +1
–2 dB
Wow and flutter: Below measurable limit
Time display: 12-hour system
Speaker: 66 mm (2 5⁄8 inches) diam., 6 Ω, cone type
(2)
Input:
Audio In jack (stereo minijack): minimum input
level 245 mV, impedance 47 kΩ
Power outputs:
1.4 W + 1.4 W (at 6 Ω, 10 % harmonic distortion)
Power requirements: 120 V AC, 60 Hz
Dimensions:
Approx. 362 s 105 s 319 mm (w/h/d)
(Approx. 14 1⁄4 s 4 1⁄5 s 12 5⁄8 inches)
incl. projecting parts and controls
Mass: Approx. 3.2 kg (7 lb 1 oz)
Radio section
Frequency range:
FM: 87.5 – 108 MHz
AM: 530 – 1 710 kHz
Antennas:
FM: AC power cord
AM: Built-in ferrite bar antenna
Supplied accessories:
mounting screws (M5 screw) (4)
template (1)
spacers (4)
cord clamp (1)
remote commander (1)
audio cable (1)
digital music player holder (1)
Design and specifications are subject to change
without notice.
FM/AM CD KITCHEN CLOCK RADIO
9-887-533-02
Sony Corporation
2007B05-1
© 2007.02
Personal Audio Division
Published by Sony Techno Create Corporation
ICF-CDK70
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
CAUTION
Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
To Exposed Metal
Parts on Set
0.15 µF
1.5 kΩ
AC
voltmeter
(0.75 V)
TABLE OF CONTENTS
1.
SERVICING NOTES ...............................................
3
2.
GENERAL ..................................................................
4
3.
DISASSEMBLY
3-1. Disassembly Flow .......................................................... 5
3-2. Cabinet (Upper) Section ................................................. 5
3-3. Mechanism Deck (DLM3A23-11)
(When TRAY carries out movable.) ............................... 6
3-4. Mechanism Deck (DLM3A23-11)
(When TRAY does not carry out movable.) ................... 7
3-5. Cabinet (Front) Section ................................................... 8
3-6. CD Lid Assy.................................................................... 8
3-7. Optical Pick-up Block (KSM-213CCP) ......................... 9
3-8. How To Pull Out Tray ..................................................... 10
3-9. Belt (DLM3A) ................................................................ 10
4.
TEST MODE ............................................................. 11
5.
ELECTRICAL ADJUSTMENTS ......................... 13
6.
DIAGRAMS
6-1.
6-2.
6-3.
6-4.
6-5.
6-6.
6-7.
6-8.
6-9.
6-10.
6-11.
6-12.
Printed Wiring Board - CD Board - ................................
Schematic Diagram - CD Board - ...................................
Printed Wiring Board - TU Board - ................................
Schematic Diagram - TU Board - ...................................
Schematic Diagram - MAIN Board (1/2) - .....................
Schematic Diagram - MAIN Board (2/2) - ....................
Printed Wiring Board - MAIN Board - ...........................
Schematic Diagram - PANEL/KEY Section - ................
Printed Wiring Boards - PANEL Section - .....................
Printed Wiring Boards - KEY Section - ..........................
Printed Wiring Boards - POWER SUPPLY Section - ....
Schematic Diagram - POWER SUPPLY Section - .........
7.
EXPLODED VIEWS
7-1.
7-2.
7-3.
7-4.
7-5.
Cabinet (Upper) Section .................................................
Cabinet (Front) Section ...................................................
Cabinet (Lower) Section .................................................
CD Lid Assy Section.......................................................
CD Mechanism Deck Section (DLM3A23-11) ..............
8.
ELECTRICAL PARTS LIST ................................. 40
18
19
20
21
22
23
24
25
26
27
28
29
35
36
37
38
39
Earth Ground
Fig. A.
Using an AC voltmeter to check AC leakage.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
SAFETY-RELATED COMPONET WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE
PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
ICF-CDK70
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
CHUCK PLATE JIG ON REPAIRING
On repairing CD section, playing a disc without the CD lid, use
Chuck Plate Jig.
• Code number of Chuck Plate Jig: X-4918-255-1
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
3
ICF-CDK70
This section is extracted
from instruction manual.
SECTION 2
GENERAL
AC power cord

Cord clamp
Magnet
Size AAA
(R03) 2
The number 5 and the VOL +
buttons have a tactile dot.
Features
TIMER indicator
CD  button have a tactile dot.
3-CD changer
CD-R/RW playback function
Bass Reflex sound system
FM/AM Digital Tuner with 30 station presets
Audio In jack for digital music player connectivity
Easy-to-set countdown timer for cooking
Digital music player holder and cable (supplied)
Magnetic remote commander (supplied)
Installing the Unit Under a
Cabinet
(See Fig. )
Caution
Please read the following before
installing the unit
There is a tactile dot
next to VOLUME +.
Turn
Push

Spacer
L (Low)
Template
Dot
H
L
Due to its heavy weight, the unit should be installed
with great care.
Installation of the unit requires two persons.
Use tools carefully while installing of the unit.
Be sure that the cabinet that is used is sturdy enough
to support the weight of the unit.
To reduce the risk of fire, do not place any heating or
cooking appliance beneath this unit.
Install the unit so that its AC power cord can be
connected directly to a wall outlet. Do not use a
converter or extension cord.
Be sure that the AC power cord has no slack during
use of the unit, since the cord acts as an FM wire
antenna. If the AC power cord has some slack, wind
it around the cord hook so as to eliminate the slack.
The unit has a built-in ferrite bar antenna for AM
radio reception. Confirm that AM reception is
acceptable before finally attaching the unit.
Install the unit as far as possible from sources of
noise (for example, a refrigerator, microwave oven or
fluorescent lamp).
This unit is not waterproof. Install it where it will
not be exposed to splashing by water, as this may
damage the unit.
To reduce the risk of fire or electric shock, do not
touch the AC power cord with wet hands.
Never place objects between the top of the unit and
the bottom of the cabinet. This could cause the unit
to fall.
Make sure the unit’s four screws are fastened tightly.
After installing the unit, do not pull down on it or
hang something heavy on it.
1
Decide on the installation location and
orientation of the unit based on the best
reception that is possible (see “Improving
the Reception”).
2
Mark the position of the 4 holes by using
the supplied template. Use a drill to make
the holes (size 6.5 mm diam., 9/32 inch). (See
Fig. -)
Mounting screw
3
4
When the cabinet door overhangs the shelf
and obstructs the unit, you can adjust the
unit/shelf height.
First set the L mark to the dot which
becomes the lowest position, then you
can adjust the height in 4 steps (H L)
by turning the spacer counterclockwise
(See Fig. -). The unit can be installed
without the spacer.
Install the unit with the supplied mounting
screws. (See Fig. -)
Note
If you lose the supplied screws, please purchase #10 or
M5 screws.
4
Installing the Batteries
into the Remote
Commander
(See Fig. -)
Insert two size AAA (R03) batteries (not supplied).
When to replace the batteries
With normal use, the batteries should last for about
six months. When the remote no longer operates the
CD kitchen clock radio, replace all the batteries with
new ones.
Notes
Do not charge the dry batteries.
If you do not intend to use the remote for a long
time, remove the batteries to prevent damage by
leakage and corrosion.
Use of Magnet (See Fig. -)
A magnet is provided on the back of the remote so
that it can be attached a refrigerator or other iron
surface.
However, do not operate the remote while it is
attached in this manner.
Note
Do not place the remote commander near magnetic
cards such as credit cards.
Setting the Clock
1
Plug in the unit.
2
Hold down CLOCK/D.S.T until a short beep
sounds.
“AM 12:00” flashes in the display.
The hour starts to flash in the display.
3
Turn the TIMER jog dial towards + or
– repeatedly until the correct hour appears
in the display.
4
Press TIMER once.
The minute flashes.
5
Repeat steps 3 and 4 to set the minute, and
press TIMER.
Two short beeps sound and the seconds start
incrementing from zero.
12-hour system: “AM 12:00” = midnight
In step 4 and 5, you can press CLOCK/D.S.T instead
of TIMER.
To the display to summer time
(daylight saving time)
Press CLOCK/D.S.T.
“ ” is displayed and the time indication changes to
summer time.
To deactivate the summer time function, press
CLOCK/D.S.T again.
ICF-CDK70
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1.
DISASSEMBLY FLOW
Note 1: The process described in
SET
can be performed in any order.
Note 2: Without completing the process described in
, the next process can not be performed.
3-2. CABINET (UPPER) SECTION
(Page 5)
3-3. MECHANISM DECK (DLM3A23-11)
(When TRAY carries out movable.)
(Page 6)
3-4. MECHANISM DECK (DLM3A23-11)
(When TRAY does not carry out movable.)
(Page 7)
3-5. CABINET (FRONT) SECTION
(Page 8)
3-7. OPTICAL PICK-UP BLOCK
(KSM-213CCP)
(Page 9)
3-6. CD LID ASSY
(Page 9)
3-8. HOW TO PULL OUT TRAY
(Page 10)
3-9. BELT (DLM3A)
(Page 10)
Note: Follow the disassembly procedure in the numerical order shown below.
3-2.
CABINET (UPPER) SECTION
six screws (B2.6)
five screws (B2.6)
screw (B2.6)
three screws (B2.6)
screw (B2.6)
screw (M2.6)
cabinet (upper) section
screw (B2.6)
screw (B2.6)
connector (CN417)
5
ICF-CDK70
3-3.
MECHANISM DECK (DLM3A23-11)
(When TRAY carries out movable.)
cover (tray)
two claws
Press the OPEN/CLOSE button
to open the tray.
Close the tray.
two screws (B2.6)
two screws (B2.6)
R mechanism deck
(DLM3A23-11)
flexible flat cable (13 core)
(CN305)
flexible flat cable (14 cor
(CN801)
Lift up the mechanism deck (DLM3A
in the direction of an arrow.
6
ICF-CDK70
3-4.
MECHANISM DECK (DLM3A23-11)
(When TRAY does not carry out movable.)
Raise the cabinet (front) section
backside as shown in a figure.
screw
screw
Lift up the mechanism deck (DLM3A23-11)
in the direction of an arrow.
two screws (B2.6)
mechanism deck
(DLM3A23-11)
two screws (B2.6)
two bosses
flexible flat cable (14 core)
(CN801)
flexible flat cable (13 core)
(CN305)
7
ICF-CDK70
3-5.
CABINET (FRONT) SECTION
cabinet (front) section
screw
flexible flat cable
(4 core) (CN409)
flexible flat cable
(14 core) (CN402)
flexible flat cable
(9 core) (CN413)
screw
flexible flat cable
(12 core) (CN401)
3-6.
CD LID ASSY
boss
CD lid assy
flexible flat cable (6 core)
(CN411)
boss
8
ICF-CDK70
3-7.
OPTICAL PICK-UP BLOCK (KSM-213CCP)
two floating screws (PTPWHM 2.6)
two coil springs (insulator)
two insulators
two floating screws (PTPWHM 2.6)
two coil springs (insulator)
two insulators
mechanism deck
(back side)
RB optical pick-up block
(KSM-213CCP)
R CD board
Remove soldering from
the four points.
flexible flat cable (16 core)
(CNP701)
screw
(BVTT2 s 6)
9
ICF-CDK70
3-8.
HOW TO PULL OUT TRAY
optical pick-up block
Pull out the tray.
Note: When the optical pick-up block in which
the optical pick-up block is chucking and
which cannot draw out TRAY is chucking,
please draw out TRAY after removing an
optical pick-up block.
"
gear
A gear " portion can be pushed to the limit of
the direction of an arrow.
3-9.
BELT (DLM3A)
two screws
two screws
cover
belt (DLM3A)
belt (DLM3A)
10
ICF-CDK70
SECTION 4
TEST MODE
CD SHIP MODE
Function to put tray of disc 1 into state of chuck for transportation
is installed in this set.
Procedure:
1. Turn the power on, and put it into the state that there is no CD
in the disc tray.
2. Press two keys of the [x] and [1] simultaneously.
3. The message “0000” is displayed and the tray is chucked.
CDM RESET
Mode to initialize CD mechanism deck.
Procedure:
1. Turn the power on.
2. Press the [x] key for five seconds, and CD mechanism deck is
initialized.
PANEL TEST
Mode that test LCD, and display the version and destination.
Procedure:
1. Turn the power on.
2. Press three keys of the [x], [2] and [.] simultaneously.
Then all segments of liquid crystal display are turned on.
3. Press the [1] key, the destination and version are displayed.
4. Press the [2] key, the released date of the micro computer is
displayed.
5. To exit from this mode, perform the step 2.
11
ICF-CDK70
CD TEST MODE
Procedure:
1. Turn the power on.
2. Press three keys of the [x], [3] and [TUNING MODE] simultaneously.
3. When the CD test mode is activated, “88” is displayed.
4. Insert the CD to the tray of disc 1, and press the [u] key to
the playback.
5. Operate it referring to the figure below.
Fig. 1 Method of operating CD test mode
NORMAL MODE
2 key
2 key
FOCUS 2 MODE
Y + 3 +
TUNING MODE key
Auto adjustment: NG
Auto adjustment: OK
2 key
STOP 1 MODE
Y key
STOP 2 MODE V key
81
82
MODE key
Whenever the
MODE key is
pressed, each
adjustment value
is displayed.
MODE key
V
key
Y key
FOCUS 1
MODE
V key
Y
key
COMMAND
FORWARDING
MODE
ALL SERVO
ON MODE
V key
P-
V key
FMODE key
Whenever the
MODE key is
pressed, each
adjustment value
is displayed.
A-
2 key
MODE key
V key
V key
Y key
88
3 key
Y key
F-
MODE key
V key
INITIAL
(TEST MODE IN)
Y key
AUTO
ADJUSTMENT
MODE
TG UP MODE
(61
P-
Ykey
Whenever the V
MODE key is key
pressed, each
adjustment value
is displayed.
MODE key
Ykey
82
MODE key
3 key
Ykey
Content of adjustment value
92xx
: RF offset
94xx
: Tracking balance
95xx
: Tracking in
96xx
: Focus balance
97xx
: Focus in
EAxx
: All in setting
98xx
: VC offset
99xx
: Sled offset
9Axx
: Focus offset
9bxx
: Tracking offset
9Cxx
: AC amplifier offset
9dxx
: BD amplifier offset
9Exx
: E amplifier offset
9Fxx
: F amplifier offset
61xx
: APC reference level setting
ALL SERVO
ON MODE
(IN COMMAND
FORWARDING
MODE)
V key
V key
82
TG UP MODE
(IN COMMAND
FORWARDING
MODE)
82
12
Y
key
Note: 61, 92 to 9F, EA : register address of DSP
xx
: adjustment value (Hexadecimal number)
ICF-CDK70
SECTION 5
ELECTRICAL ADJUSTMENTS
0 dB=1 µV
TUNER SECTION
AM IF ADJUSTMENT
Adjust for a maximum reading on level meter
[AM]
Setting:
Function: RADIO
Band: AM
T1
Put the lead-wire
antenna close to
the set.
AM RF signal
generator
MAIN board
CN303 pin level meter
67
450 kHz
AM VCO VOLTAGE ADJUSTMENT
Reading on Digital
Adjustment Part
Frequency Display
Voltmeter
L4
530 kHz
1.0 ± 0.1 V
Confirmation
1,710 kHz
5.3 ± 0.4 V
+
–
set
30% amplitude
modulation by
400 Hz signal
Output level:
as low as possible
AM TRACKING ADJUSTMENT
MAIN board
CN303 pin Adjustment for a maximum reading on level meter
[FM]
Setting
Function: RADIO
Band: FM
L3
620 kHz
CT3
1,400 kHz
FM IF ADJUSTMENT
Adjust for a minimum reading on level meter
T2
TU board
TP (ANT)
FM RF signal
generator
0.01 F
level meter
67
+
–
set
75 kHz frequency
deviation by 1 kHz
signal
Output level:
as low as possible
TU board
TP (GND)
10.7 MHz
MAIN board
CN303 pin MAIN board
CN303 pin FM VCO VOLTAGE ADJUSTMENT
Reading on Digital
Adjustment Part
Frequency Display
Voltmeter
L2
108 MHz
3.0 ± 0.2 V
Confirmation
87.5 MHz
1.3 ± 0.2 V
FM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter
digital voltmeter
L1
87.5 MHz
CT1
108 MHz
TU board
TP (VT)
TP (GND)
100 k 7
Adjustment Location: TU board (See page 14)
• Repeat the procedures in each adjustment several times, and
the tracking adjustments should be finally done by the trimmer
capacitors.
13
ICF-CDK70
Adjustment Location:
– TU BOARD (Component Side) –
L2
FM VCO Voltage Adjustment
T2 FM IF Adjustment
L4
AM VCO Voltage Adjustment
T1 AM IF Adjustment
L1
CT1
L3
CT3
AM Tracking Adjustment
– TU BOARD (Conductor Side) –
TP (VT)
TP (GND)
14
TP (ANT)
FM Tracking Adjustment
ICF-CDK70
CD SECTION
RF SIGNAL CHECK
Procedure:
1. Connect the oscilloscope to TP (RF) and TP (VC) on the CD
board.
2. Insert the disc (PATD-012) (Part No. : 4-225-203-01).
3. Press the [u] button.
4. Confirm that the oscilloscope waveform is as shown in the figure below. (eye pattern)
A good eye pattern means that the diamond shape (◊) in the
center of the waveform can be clearly distinguished.
• RF signal reference waveform (eye pattern)
VOLT/DIV: 0.2 V (with the 10: 1 probe in use.)
TIME/DIV: 200 ns
0.7 to 1.7 Vp-p
When observing the eye pattern, set the oscilloscope
for AC range and raise vertical sensitivity.
Connecting Location:
– CD Board (Conductor Side) –
TP (VC) TP (RF)
IC701
15
ICF-CDK70
MEMO
16
ICF-CDK70
SECTION 6
DIAGRAMS
• Circuit Boards Location
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
TU board
For Printed Wiring Boards.
For Schematic Diagrams.
Note:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
•
W : indicated side identified with part number.
•
f : internal component.
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Note:
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
•
f : internal component.
• C : panel designation.
Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.
MAIN board
CD board
TIMER board
POWER board
REMOTE CONTROL board
Note:
Les composants identifiés
par une marque 0 sont
critiques pour la sécurité.
Ne les remplacer que par
une piéce portant le numéro spécifié.
LCD board
AMP board
• A : B+ Line.
• C : adjustment for repair.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
- CD Board no mark : CD play
- TU Board no mark : FM
(
) : AM
- Other Boards no mark : FM
(
) : CD play
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms
• Signal path.
F
: FM
f
: AM
J
: CD play
i : AUDIO IN
• Abbreviation
CND : Canadian model
LED board
MEGA BASS board
JACK board
KEY board
ICF-CDK70
17
17
VOL board
ICF-CDK70
6-1.
• Semiconductor
Location
2
1
3
•
: Uses unleaded solder.
4
5
6
Location
R728
R727
C
C
C771
C763
JW705
C762
C764
R763
R769
E
R764
R736
JW716
JW717
JW718
JW719
16
JW720
R761
C702
C761
JW724
JW722
C760
R755
2
5
R771
C772
CNP702
A
MAIN
BOARD
CN801
11
C742
C743
C745
14
C747
R748
FB702
FB701
C728
R743
C729
C733
R746
R744
R742
R739
C732
R745
JW731
C731
C725
C726
JW738
JW704
JW703
JW702
JW701
JW707
R741
C770
R740
R738
C722
R747
C727
R733
18
C744
JC702
C739
FB704
30
X701
D701
JW732
R734
JW730
JC701
C720
18
R751
35
C738
26
C734
R735
ICF-CDK70
JW711
C754
C753
C740
C741
39
1
20
C717
G
R752
(Page 24)
3
10
C714
45
15
R722
F
R770
R749
5
C713
R758
R750
C769
C712
IC701
C716
C721
C750
R757
52
R718
R716
E
R754
FB703
C758
R719
C710
R760
C708
C705
C768
R720
R778
TP
(RF)
TP
(VC)
JW729
C749
R776
C751
R709
R710
C707
C756
C755
C767
R708
R773
R705
R707
E
B
JW723
R706
R775
R777
C711
R721
JW733
JW728
C706
Q704
R703
R756
JW727
R702
C
R762
C757
JW726
R774
R704
C774 R715
OPTICAL
PICK-UP
BLOCK
(KSM-213CCP)
R701
JW725
1
JW721
JW706
R711
C704
JW708
R714
R753
10
JW710
2
M702
(SLED)
M
C746
E
C748
15
CNP701
D702
B
5
C701
C
Q701
1
C703
C
D
28
C724
E
B
22
JW712
R737
JW734
Q703
B
Q702
C723
C719
C718
R723
JW735
1
JW713
R729
R725
R724
JW736
7
21
R726
JW737
B
15
R766
R731
R730
8
IC702
M701
(SPINDLE)
M
R765
R732
14
R767
C-1
C-3
B-3
D-4
S701
(LIMIT)
Q701
Q702
Q703
Q704
A
R713
E-3
B-4
JW715
IC701
IC702
CD BOARD
JW714
G-4
C-4
C765
D701
D702
R768
Ref. No.
• See page 17 for Circuit Boards Location.
PRINTED WIRING BOARD - CD Board -
11
1-871-580-
(11)
ICF-CDK70
6-2.
• See page 30 for Waveforms.
SCHEMATIC DIAGRAM - CD Board -
• See page 30 for IC Block Diagrams.
Q704
2SC3052EF-T1-LEF
R762
22k
R754
47k
R753
47k
FOCUS GAIN
C761
100
10V
C760
10
R714
4.7
C702
100
10V
R713
4.7
C703
1
C750
47p
C757
47p
R774 22k
(RF)
22k
R705
10k
R708
10k
R709
22k
C
R707 22k
F
R710
22k
R777
10k
R778
47k
C706
100
10V
VR
PD
R711
100
C768
0.001
C708
0.1
AVDD1
T+
T+
T-
T-
F-
F-
C705
1
C712
220p
R716
470k
R720
C746 0.0022
R751 470
C747 0.0022
FB704
0.01
0
470k
C770
MONI0
BUSY
FEO
RESETX
BTC
R/W
22k
R745
0
R744
100
C732
0.001
R743
2.2k
C731
0.01
C729
100p
C728
22p
R741
C733
100
10V
C734
0.01
R746
100
FB701
0
FB702
0
0.01
D701
R742
C738
470
10V
R771
220k
MA111-TX
100
CNP702
14P
DOUT
AVDD(3.3V)
DIN
SUBSYQ
LON
CLK
CLK88
SDOUT
SDIN
TDOUT
JUMPO
FDOUT
AGND1
ASY
CLVOUT
LD
PCO
0.1
R748
MUTE
FEN
FCO
1k
C714
X701
16.9344MHz
470
XPLCK
CD DSP
IC701
BU9532KS2
PD
R721
R747
DVDD
PKC
C713
0.0022
R752 470
XI
VBIAS
F
C710 C711
100p 22p
C744
XO
E
R718 R719
47k
47k
0.001
DGND
BD
F+
0.1
C745
C772
1
AC
F+
470
(VC)
GND
LD
470
R749
C742
0.0022
TP
C707
100
10V
R776 10k
R750
C743
0.001
C739
100
10V
AVDD2
R704
R706 10k
JC702
0
R760
1k
LDACO
R703 22k
B
C758
0.047
C748
1
C740
VCDAC
A
FB703
0
R773 10k
R756
22k
AGND2
R702 10k
C755
1
RFRPRFM
R701 22k
D
C749
100p
SC
E
C756
22p
C769
10
50V
C741
1
TZCRFM
VDD
EQO
VC
TP
R775 10k
C767
0.0022
R755
47k
C751
0.0022
C701
0.1
CONTROL
CNP701
16P
R757
47k
TEN
POWER
R758
10k
C753
100p
TEO
AUTOMATIC
C754
220p
R761 CONTROL SWITCH
1k
RDACO
R715
100k
RFI
Q701
2SA1235TP-1EF
C774
1
CACG
C704
100
10V
D702
MA111-TX
MCK
C727
22p
R740 100
C726
22p
R739 100
L-OUT
D-GND
R-OUT
RESET-X
D-IN
RW
MCK
SUBSYQ
M702
SL+
SL-
SL-
SL+
(SLED)
C725
0.001
R738
100
D-OUT
BUSY
R770
1k
Q702,703
R722
220
FOCUS GAIN UP SWITCH
LIM
JC701
0
C717
0.22
VM(6V)
R736
2.2k
M-GND
C722
0.1
R732
2.2k
R729
22k
R730
100k
S701
(LIMIT)
ICF-CDK70
19
19
OP
T+
T-
SP+
SP-
R765
1k
47p
47k
C765
NC
F+
T+
OPIN
FT-
GND
FIN
(TIN)
OPOUT
VCC
(FIN)
GND
TIN
VCC
RST
R763
2.2k
R766
R764
2.2k
SPIN
IC702
BA5826SFP-E2
VREF
COIL/MOTOR
R735
4.7k
OP
C721
10
50V
REGO
R734
47k
DRIVE
C723
1
F+
R731
2.2k
R733 22k
C720 0.22
R768
220
F-
OP
R769
10k
MUTE
C719
1
R725
47k
R728
22k
(SLIN)
R726
4.7k
R724
100k
REG-B
C718
1
Q702
2SC3052EF
-T1-LEF
Q703
2SC3052EF-T1-LEF
C763
1
R767
470
SLIN
C724
1
SL-
SL+
C716
4.7
50V
R723
47k
SL-
SP-
SL+
SP+
R737
2.2k
GND
SP+
SP+
(SPINDLE)
SP-
C762
0.1
SP-
M701
R727
220
C764
220
10V
C771
1
(Page
22)
ICF-CDK70
6-3.
PRINTED WIRING BOARD - TU Board -
1
2
• See page 17 for Circuit Boards Location.
3
4
•
: Uses unleaded solder.
5
6
7
8
9
10
TU BOARD
A
L3
AM FERRITE-ROD
ANTENNA
B
TP (VT)
TP
(ANT)
J
JW14
L1
TP (GND)
POWER
BOARD
CN902
(Page 28)
1
TP (CV)
C
(SHIELD CASE)
R5
B
MAIN
BOARD
(Page 24)
D
L2
C13
T1
11
IC2
L4
IC1
T2
E
11
1-863-438-
• Semiconductor
Location
Ref. No.
Location
D1
D2
D3
D10
D11
B-7
C-6
C-6
B-9
B-9
IC1
IC2
D-7
D-3
ICF-CDK70
20
20
(11)
ICF-CDK70
6-4.
• See page 30 for Waveforms.
SCHEMATIC DIAGRAM - TU Board -
L3
D3
KV1520NT
AM FERRITE-ROD
• See page 30 for IC Block Diagrams.
L4
C41
220p
ANTENNA
AM OSC
C42
100p
CV
C43
22p
JC11
0
R41
10k
CT3
C49
0.01
R40
220k
C39
0.1
TP
(VT)
C37
0.01
C32
1000p
R30
22k
R32
100k
FM
C51
22p
R33 C30
10k 0.01
C31
22p
R14
1k
JC3 0
C59
100p
R55 R53
10k 4.7k
C95
1000p
C57
1000p
C55
100p
C21
1
50V
AM IN
FM IN
FM/AM PLL
IF IN
BAND
MO/ST
ST-IND
VDD
VSS
MW/LW
BAND
PD
CE
MUTE
XOUT
LPF1
LPF2
/MO-ST
/BAND
L-OUT
AGC
QUAD
R-OUT
MPX-IN
DET-OUT
IF-OUT
GND2
ST-IND
IF-IN
FM
OSC-
OUT
IF-IN
AM OSC
VCC2
AM
FM OSC
OUT
MIX-
AM
RF-IN
CUT
VCC1
RF-IN
IC1
TA2149BN
FM
GND1
FM/AM IF AMP,DET,MPX
AM LOW
RF-OUT
FM
11
FM/AM RF AMP,MIX,OSC,
C12
4.7
50V
R2
470
D11
1SS355
C1
47p
C7
5p
C9
10p
T1
IC2
LC72137M-TLM
C60
1000p
JC13
0
C61
100p
JC4
0
C62
100p
C63
100p
R4
10k
R94
1k
R13
1k
AM IFT
R92
220
D10
1SS355
(Page 29)
C56
1000p
C20
0.1
CV
POWER
BOARD
CN902
C54
220
10V
R51
10k
X1
75KHz
C22
0.1
R11
2.2k
C23
1
50V
J
R63
10k
R54
470
C24
220p
TP
(ANT)
C52
10p
R24
220
OSC
RF
C65
4.7
50V
R65
10k
R91
220
D2
KV1471E
R31
4.7k
L2
C53
0.22
LP-IN
FM
R52
0
DO
L1
C34
0.01
C13
0.01
C33
0.01
R50
1k
TP (CV)
LP-OUT
C35
0.01
CT1
C80
0.01
CL
D1
KV1471E
C47
10p
XIN
JC12
0
DI
L11
1µH
C66
100p
R60
2.2k
R59
2.2k
R56
220
R57
100
L21
10µH
C68
100p
CF4
R61
2.2k
JC5
0
CNP1
11P
R-MUTE
R58
2.2k
R-COUNT
R-CLOCK
T2
R-DATA
FM
R1
470
IFT
JC6
R5 0
1k
CF2
TU-LCH
JC2 0
JC34
R10
47
JC1 0
TU-6V
0
TU-RCH
GND
C15
0.022
R3
10k
C10
1
50V
R-LAT
JC33
0
C8
1000p
C4
1000p
C11
0.1
C18
220
10V
VT
C29
100
10V
C14
0.022
ICF-CDK70
21
21
C27
100p
C26
100p
TP
(GND)
S-GND
B
MAIN
(Page 22)
ICF-CDK70
• See page 30 for Waveforms.
SCHEMATIC DIAGRAM - MAIN Board (1/2) -
(1/2)
• See page 33 for IC Pin Function Description.
Q803
RT1N144C-TP-1
R866
Q804,805
VT
C835
0.01
C833
3p
C832
47p
CN401
12P
10k
C838
47p
C840
22p
C834
6V
U-GND
47p
RMC VCC
3p
L804
Q802
2SC3052EF-T1-LEF
Q801
2SC3052EF-T1-LEF
Q801,802
SHIFT CLOCK
C864
100p
B+ SWITCH
C836
SEG16
10k
R480
T+
1k
R863
T1k
1k
C891
0.1
R867
X802
1k
R870
C831
100p
0.01
47p
C837
T-LED
4.19MHz
10k
10k
10k
R875
R874
C841 100p
1k
100p
C843
C865
100p
R-CH
TU-RCH
GND
R878
TU-6V
1k
L-CH
TU-LCH
R879
TCE
R-LAT
C842 100p
100p
TDAT
C845
R-DATA
1k
TCLK
1k
R-CLOCK
R881
TCNT
R864
C839
R876
1k
R880
R-COUNT
10k
R865
TON
R897
22k
C855
100p
11 R-MUTE
(Page 21)
TCNT
TMUT
TMUT
TCLK
MUTING
R872
6-5.
COM0
COM0
COM1
COM1
COM2
COM2
COM3
COM3
SEG0
SEG0
SEG1
SEG1
SEG2
SEG2
SEG3
SEG3
SEG4
SEG4
(Page 25)
L805
S-GND
CBSY
R804
1k
1k
C803
O-TU-CE
I-CO-LIMSW
100p
C804
CDIN
R805
CMCK
R806
0
R808
0
I-CD-BUSY
0
SEG16
NC
NC
NC
NC
VCC
X1
VSS
X0
NC
SEG14
SEG13
SEG12
SEG10
I-CD-DOUT
SEG9
O-CD-RW
SEG8
I-RMC
SEG7
O-POWER CD
SEG6
O-AMP STANDBY
SEG5
O-4.5V CE
SEG4
A
X0A
SEG3
VM
X1A
C807
10p
100p
C810
A-STBY
100p
C811
VT
C813
22p
S-GND
C863
100p
M-GND
X801
C812
100p
32.768kHz
C814
22p
R814
1k
SYSTEM CONTROLLER
100p
C887
1
47p
R815
470
M2-
R365
470
M2-
R366
470
M1-
R367
M1+
R368
C818
100p
R816
470
BUZZER
C816
100p
R817
1k
VCC
SEG1
O-CD-XRST
470
O-MO2-
SEG0
O-MO2+
COM3
O-MO1-
COM2
O-MO1+
COM1
O-A MUTE
COM0
O-DISC3KEY LED
SW6
R823
47k
C823
1000p
RESET-X
SW5
R824
47k
C824
1000p
R882
0
CRST
D-IN
C847
10p
R883
1k
CDIN
RW
C848
100p
R884
1k
CRW
MCK
C849
10p
R885
470
CMCK
R886
470
CSUBSYQ
SUBSYQ
0
JC805
0
R887
1k
CBSY
LIM
R888
1k
CLMSW
I-TRSW5
SEG9
SEG10
SEG15
SEG10
R478
10k
SEG14
SEG11
SEG11
R477
10k
SEG13
SEG12
SEG12
R476
10k
SEG12
SEG13
SEG13
R475
10k
SEG11
SEG14
SEG14
R474
10k
SEG10
SEG15
SEG15
R473
10k
SEG9
SEG16
SEG16
R472
10k
SEG8
T-LED
T-LED
R471
10k
SEG7
RMC
R470
10k
SEG6
R469
10k
SEG5
R468
10k
SEG4
R467
10k
SEG3
R466
10k
SEG2
MD1
(Page 25)
RMC
CN409
4P
C890
0.1
R465
10k
SEG1
R464
10k
SEG0
R463
10k
COM3
R462
10k
COM2
R461
10k
COM1
R460
10k
COM0
R860
1k
R859
1k
R858
1k
R855
1k
R854
0
R853
0
DISC3
R852
0
DISC2
U-GND
R416
R895
22k
C889
0.01
C830
470
KEY0
T+
C896
100p
T+
T-
C897
100p
T-
(Page 25)
R415
2.2k
100p
CN411
6P
MD2
DISC1
KEY0
U-GND
(Page 25)
6V
SW8
R825
47k
C825
1000p
KEY1
R443
4.7k
6V
KEY1
0.1
1k
1k
1k
R846
R850
1k
R839
R848
0
100p
100p
C402
C403
DATA
R834
100p
C401
0
0
R828
470
R827
R831
470
VCC
R826
C854
I-TRSW6
SEG8
CDO
BUSY
VM(6V)
MD0
0.01
JC804
I-TRSW2
I-BASS BOOST
ON/OFF
R-OUT
ITRSW8
R-OUT
I-SUFFIX 2
1000p
I-SUFFIX 1
C822
I-RESET
I-SUFFIX 0
47k
O-DISC1KEY LED
I-TRSW7
VSS
R822
O-DISC2KEY LED
I-TRSW1
I-AC IN
SW2
L807
I-TRSW3
I-CD-SUBSYQ
SW7
1000p
I-REG3.3V-CHK
1000p
C821
I-KEY2
C820
47k
I-KEY1
47k
R821
I-KEY0
R820
L-OUT
I-REG4.5V-CHK
SW1
L806
SEG7
SEG8
10k
VLCD
O-BUZZER
I-REG6.0V-CHK
1000p
AVSS
C819
O-VOL-CLK
47k
O-VOL-DATA
SW3
R819
SEG6
SEG7
VSS
VSS
470
A-MUTE
SEG2
IC801
MB90802PF-G
-124E1
VCC
AVCC
C844
0.1
D-GND
M-GND
1k
O-BASS BOOST OFF
L-OUT
D-OUT
1k
R812
C888
AVDD(3.3V)
R811
C866
CRST
CN801
14P
1k
C815
D-GND
B
R810
I-ENCODER-
P-CD
100p
C809
I-ENCODER+
1k
R809
RMC
SEG5
SEG6
R479
SEG11
O-CD-MCK
1k
R807
SEG5
SEG9
SEG15
O-CD-DIN
CDO
(Page 19)
1k
100p
CRW
(Page 23)
R802
O-TU-DO
O-TIMER LED
100p
C802
R803
1k
I-ENCODER-TIMER+
TCE
CLMSW
R801
I-ENCODER-TIMER-
100p
C801
O-CLK-SHIFT FM
TDAT
O-CLK-SHIFT AM
TON
O-POWER TUNER
JC802
0
O-TU
-CLK
Q805
RT1N144C-TP-1
O-TU-MUTE
C314
0.01
O-POWER AUDIO IN
CN402
14P
I-TU-DI
Q804
RT1P144C-TP-1
1
DATA
CLK
CLK
U-GND
C862
1
RESET
10k
10k
10k
220k
10k
R842
R844
R847
R849
R836
10k
BASS
R840
1k
1k
R442
R444
10k
10k
R829
R832
1k
10p
C827
R440
10p
C826
GND
R835
10k
ENC+
ENCR851
10k
KEY2
R445
4.7k
KEY2
RMC VCC
R441
R833
10k
R830
10k
4.7k
KEY0
4.5V
R+6V
ICF-CDK70
22
22
KEY2
KEY1
CLK
DATA
3.3V
CSUBSYQ
(Page
23)
ICF-CDK70
6-6.
• See page 30 for IC Block Diagrams.
SCHEMATIC DIAGRAM - MAIN Board (2/2) -
(2/2)
CN413
9P
R114
470k
INPUT SELECTOR,ELECTRICAL VOLUME
IC301
R2S15904SP
C113
0.1
R117
22k
C112
0.022
R116
10k
R110
47k
C111
0.047
JC101
0
C213
0.1
JC201
0
KEY2
C869
1000p
KEY1
C868
1000p
KEY2
KEY1
BASS
BASS
ENC+
ENC+
ENC-
ENC-
R111
100k
C867
KEY0
R109
2.2k
1000p
LCH
BASS L2
NC
NC
C116
220p
C216
220p
R303
R304
470
470
TRE L
C115
470p
C215
470p
C304
C305
D_GND
CLK
47p
DATA
10V
0.1
A_GND
R OUT
L OUT
IN_
R4
C301
100
10V
470k
BASS R1
C210
4.7 50V
IGOUT_R
IGOUT_L
C319 0.1
IN_L4
C212
0.022
R216
10k
C211
0.047
R217
22k
R211
100k
R103 R104
1k
2.2k
R108
470k
R107
47k
C106 1000p
C105
1 50V
IN_L TU
C103 1000p
C102
1 50V
IN_L CD
C109
100p
C108
1 50V
R112
22k
C209
100p
C208
1 50V
R212
22k
C203 1000p
C202
1 50V
C206 1000p
C205
1 50V
R208
470k
R207
47k
IN_L AU
IN_R AU
IN_R CD
IN_R
TU
C320
0.01
R203
1k
R204
2.2k
R101
10k
R201
10k
R205
1k
C104
1
50V
L-CH
L-OUT
C101
1
50V C201
1
50V
R-OUT
R-CH
C204
1
50V
KEY2
Q954
KTC3205-Y
KEY1
KEY1
KEY0
KEY0
+3.3V REGULATOR
Q955,956
REGULATOR CONTROL
CLK
DATA
R+6V
3.3V
R302
100
R301
100
R969
10
R965
47
6V
C886
220
10V
C885
0.01
RESET
C894
1
U-GND
IC802
S-80828CNMC
4.5V
NC
RMC VCC
RESET SIGNAL
GENERATOR
NC
L803
1MH
C880
100
10V
GND
CN305
13P
C960
0.01
GND
+3.3V REGULATOR
C961
220
10V
IC803
S-812C33AUA
OUT
R964
1k
A-GND
R966
10k
D951
UDZS-TE17-3.9B
P-CD
Q956
RT1N144C-TP-1
R857
47k
C884
0.01
C883
100
10V
R342
47k
SW7
R350
22k
SW7
SW2
R349
22k
SW2
SW6
R348
22k
SW6
SW5
R347
22k
SW5
SW8
R346
22k
SW8
Q355
2SA1365EF
R338
470
Q356
2SA1365EF
R339
470
Q357
2SA1365EF
R340
470
R362
22k
R341
470
D308
MA111-TX
R357
0
NC
Q350
2SC3440-F
R334
47k
Q351
2SC3440-F
Q352
2SC3440-F
R335
47k
Q353
2SC3440-F
R336
47k
R337
47k
R355
2.2
R354
2.2
R353
2.2
TU-GND
C861 100p
1
C352
0.1
Q361
2SA1235-F
D307
MA111-TX
R360
1k
D309
MA111-TX
R358
2.2k
Q360
2SA1235-F
R364
10k
M-6V
M-GND
Q359
2SC3052EF-T1-LEF
R363
10k
10V
SUPPLIED WITH
Q354
2SA1365EF
220
SW1
0.01
SW3
22k
R361
100
R345
47k
C354
22k
R351
R344
47k
C353
R352
R343
47k
(Page 29)
U-GND
0.1
SW1
POW_ON
C882
0.01
MOTOR DRIVE
SW3
A_MUTE
C857 100p
AGC
Q350-357
DECK BLOCK
C858 100p
A-STBY
6V
M1C351
A-MUTE
VT
R856
1k
0.1
COM
BUZZ
D-GND
Q358
KTA1273-Y
C350
BUZZER
L801
10mH
M2-
M1+
14
VCC
OUT
M2+
Q955
RT1P144C-TP-1
L_CH
C881
0.01
IN
L802
47MH
R963
470
R_CH
C962
0.1
VCC
GND
BLOCK
1k
ENC-
KEY2
THE ASSEMBLED
R105
ENC+
ENC-
CD MECHANISM
RCH
R209
2.2k
BASS
BASS
ENC+
(Page 22)
A-GND
C856
0.1
R210
47k
C110
4.7 50V
VOLIN_L
REF IN
VCC
C302
R214
VOLIN_R
TRE R
47p
C303 47
BASS L1
BASS R2
(Page 25)
D-GND
S-GND
VT
Q362
2SC3052EF-T1-LEF
R359
2.2k
VM
D-GND
M-GND
M2+
M2-
M1+
M1-
Q358-362
B+ SWITCH
A
B
ICF-CDK70
23
23
(Page
22)
ICF-CDK70
6-7.
• Semiconductor
Location
1
6
7
10
11
12
CD BOARD
CNP702
(Page 18)
A
Q955
E
B
Q956
C
E
2
R347
R346
C351
C350
1
13
9
8
R888
JW855
JC804
R887
C849
R886
C848
C865
C864
JC805
C810
C811
R810
R811
R812
R365
R815
C812
C815
R366
R368
R367
R816
R817
C820
C819
C821
C822
C823
C824
C825
R829
R830
C866
R803
R804
R805
R806
R807
R808
C803
C804
R831
R828
C887
JW836
JW829
C839
3
1
CN409
1
5
2
C896
6
C856
11
1-872-482
JW803
C LCD BOARD
(Page 26)
CN305
CD MECHANISM DECK BLOCK
(
SUPPLIED WITH THE
ASSEMBLED BLOCK
)
R875
C840
R876
C897
2
4
1
13
12
2
JW828
R872
C836
R870
R867
R863
R479
R477
R475
C831
R478
R476
R474
R472
R480
1
CN411
1
2
2
14
2
11
C868
CN413
CN402
12
JW804
C869
E
R866
R350
B
R864
R351
JW866
C867
JW802
Q802
R874
R416
R348
JW827
R415
R349
JW801
J
C890
L801
CN401
R352
C837
C835
L804
JW813
H
I
R860
JW814
C838
C833
C
E
B
R473
JW806
E
B
C832
Q801
C889
R461
R343
E
C
L805
R460
B
JW826
R859
JW823
E
B
Q354
JW812
Q355
C834
R858
JW811
E
JW805
R345
B
Q356
5
C
JW810
Q357
C
JW809
C
X802
C891
81
80
JW825
4
R342
C
1
R471
R339
3
IC802
R470
R338
R341
JW820
R855
R469
R340
C830
R856
C880
JW808
C353
C841
R878
R468
C
C842
R879
R466
Q350
C
C845
R880
C843
R854
R467
Q351
C
R881
C809
100
R853
R464
Q352
C
1
C894
1
2 3
1
B
Q353
JW815
JW819
R334
E
C886
IC801
R465
B
R809
51
R852
C885
IC803
C884
E
C801
R895
G
B
R344
A
R335
R336
E
B
JW807
R363
R337
E
K
D308
A
R362
D309
K
C802
JW821
R361
R897
R802
L802
C883
R364
C807
50
C862
B
JW818
A
JW817
C
JW816
E
B
JW822
+
B
R814
R844
+
F
Q359
D307
Q360
C
K
Q803
R801
+
R360
B
C881
E
C
R850
L803
C882
Q358
E
R885
C847
Q362
30
R842
R848
R851
C
R832
JW835
R441
R443
R846
R849
C855
X801
R840
R463
R101
R445
R110
R111
R847
C354
C814
31
R839
R109
R210
R211
JW857
JW830
JW831
C888
JW824
R104
R834
B
C
JW833
R865
C103
C109
C201
R209
C204
JW832
C403
R835
R836
+
R201
+
R205
+
R105
JW858
JW834
R444
JW837
C101
C102
R857
E
R112
R212
R204
R207
R208
R107
R108
R357
R358
R359
C108
JW868
C402
JW859
C104
C
C401
11
R442
+
B
Q361
JW838
+
E
C208
C202
JW839
R103
+
R203
C205
+
+
+
C352
E
C209
C203
R354
R353
C105
R355
R440
+
D
R833
14
1
F LED BOARD
(Page 26)
G VOL BOARD
(Page 27)
ICF-CDK70
24
24
B
TU BOARD
CNP1
(Page 20)
JW851
C106
C206
1
JW853
C818
R819
C816
R821
R820
R822
R823
JW860
R824
C827
C319
C861
R884
R882
JW850
JW849
JW848
JW854
JW852
R825
C110
IC301
JW845
C210
+
JW867
JW847
JW843
+
C320
+
15
R883
C211
C212
C213
C111
R214
+
JW861
C112
C113
R114
28
C
C
C314
JW844
C115
Q804
JC802
14
B
E
R217
JW841
C116
C304
C854
13
JW842
C302
C215
C305
C303
C
1
B
E
Q954
R969
CN801
C962
B
L806
R966
C844
R963
R964
K
Q805
C813
R117
C960
D951
R965
JC201
C961
B
E
C
C216
C301
C
R216
R116
R303
R301
R302
JW862
R304
B (Page 28)
JC101
AMP BOARD
CN301
14
JW846
C858
C857
1
C863
+
JW864
H
L807
A
+
G-3
G-3
G-3
G-2
G-3
G-3
G-3
G-2
F-2
F-2
F-1
E-1
E-1
G-10
G-10
E-11
B-11
B-11
B-8
B-8
B-8
9
MAIN BOARD
JW865
Q350
Q351
Q352
Q353
Q354
Q355
Q356
Q357
Q358
Q359
Q360
Q361
Q362
Q801
Q802
Q803
Q804
Q805
Q954
Q955
Q956
8
C826
C-4
F-8
G-6
F-6
5
R827
IC301
IC801
IC802
IC803
4
R826
F-2
G-1
F-1
B-7
3
: Uses unleaded solder.
A
Location
D307
D308
D309
D951
2
•
R462
Ref. No.
• See page 17 for Circuit Boards Location.
PRINTED WIRING BOARD - MAIN Board -
D LCD BOARD
(Page 26)
E
TIMER
BOARD
(Page 26)
(11)
E
ICF-CDK70
SCHEMATIC DIAGRAM - PANEL/KEY Section -
1
S402
S404
S403
OPEN/CLOSE
EX-CHANGE
TUNING MODE
R402
470
R401
220
3
S416
KEY1
KEY1
KEY2
KEY2
D-GND
TUNE/PRESET/
ROTARY ENCODER
VOLUME
S417
MEGA BASS
D-GND
3
1
TRACK -
JOG +
R403
1k
GND
R404
1k
JOG -
6-8.
OFF
ON
R411
1k
S409
S408
CD
OFF
R410
1k
R409
470
S407
9
R408
220
KEY2
R425
1k
KEY1
S406
R424
1k
TUNE/PRESET/
TRACK +
ENC+
KEY1
KEY1
ENC-
BASS
BASS
D-GND
D-GND
LCH
(Page 23)
CN418
6P
CN417
6P
BASS
RADIO/BAND
AUTO PRESET
D-GND
LCH
A-GND
1
LCH
A-GND
RCH
S401
AUDIO IN
RCH
1
LCH
A-GND
LCH
A-GND
RCH
RCH
1
FB201
A-GND
FB101
RCH
3
C207
1000p
3
J301
C107
1000p
AUDIO IN
FB301
12
6V
R439
1k
U-GND
LCD401
LIQUID CRYSTAL DISPLAY
D404
1L341Y22
COM2
COM3
SEG0
COM0
REMOTE CONTROL
RECEIVER
IC401
NJL23H400A
R436
470
R435
1k
R434
470
D403
1L341Y22
D402
1L341Y22
3
2
Q403
2SC3052EF-T1-LEF
D401
1L341Y22
1
Q402
2SC3052EF-T1-LEF
Q401
2SC3052EF-T1-LEF
BACK LIGHT
COM2
1
COM3
SEG7
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
RMC
R483
4.7k
SEG15
RMC
ROTARY
Q404
2SC3052-EF-T1-LEF
ENCODER
R422
470
TIMER PUSH
LED DRIVE
R417
4.7k
START/STOP
R423
220
R414
1k
R419
2.2k
1
TT+
KEY0
U-GND
4
1
(Page 22)
ICF-CDK70
25
25
U-GND
KEY0
DISC1
DISC3
R427
1k
S415
R418
22k
6V
DISC2
R426
1k
SEG13
SEG14
R482
22k
D.S.T
SEG12
SEG16
T-LED
T-LED
SEG9
U-GND
SEG11
R485
4.7k
CLOCK/
100p
SEG6
RMC VCC
SEG10
R484
22k
LED DRIVE
100p
SEG5
MODE
SEG8
SEG9
R487
4.7k
S413
C407
SEG8
R420
1k
C406
SEG7
SEG4
S414
RMC
SEG6
SEG3
YEL
SEG5
R421
2.2k
TIMER
R486
22k
Q401-403
T-LED
14
D406
L-34HD
SEG2
WHT
1
SEG1
R428
1k
U-GND
SEG4
C408
0.1
RMC VCC
SEG3
SEG0
BLK
SEG2
(Page 22)
R437
1k
LCD
COM1
RED
(Page 22)
SEG1
GND
COM1
OTU
COM0
R438
470
R431
470
VCC
R430
470
RMC VCC
R413
470
S412
S411
S410
3
2
1
R412
220
6
(Page 22)
ICF-CDK70
6-9.
PRINTED WIRING BOARDS - PANEL Section -
1
2
• See page 17 for Circuit Boards Location.
3
4
•
: Uses unleaded solder.
5
6
7
8
10
11
TIMER BOARD
REMOTE CONTROL BOARD
3
1
9
S414
BLK
R419
C407
TIMER
PUSH
START/STOP
RED
YEL
1
WHT
C406
2
S415
ROTARY
ENCODER
1
R421
4
5
R420
IC401
R426
3
R427
R428
A
C408
MODE
S413
CLOCK/
D.S.T.
4
D406
B
11
TIMER
11
1-872-486-
(11)
(11)
1-872-485-
MAIN
BOARD
CN409
E
(Page 24)
D
LCD BOARD
C
MAIN BOARD
CN402
(Page 24)
MAIN BOARD
CN401
(Page 24)
C
R483
6
D401
11
1
1-872-487-
(11)
D401,S410
1
E
• Semiconductor
Location
Location
D401
D402
D403
D404
D406
D-7
D-9
D-11
D-1
B-5
IC401
A-5
Q401
Q402
Q403
Q404
D-7
D-9
D-11
C-2
ICF-CDK70
26
26
1
R412
R413
B
Q402
D402,S411
2
D402
C
B
E
R487
R486
B
Q401
S412
R485 E
Q403
C
R439
R438
E
1
Ref. No.
S411
S410
LCD401
LIQUID CRYSTAL DISPLAY
21
(Page 24)
12
1
14
MAIN BOARD
CN411
R484
YEL
BLK
RED
D
WHT
1
F
R437
R436
LED BOARD
R423
C
R422
R417
R414
B
Q404
R434
R435
E
R482
)
R418
D404
LCD
BACKLIGHT
R431
(
R430
C
1-872-488D403,S412
3
D403
11
(11)
ICF-CDK70
6-10. PRINTED WIRING BOARDS - KEY Section -
1
2
• See page 17 for Circuit Boards Location.
3
4
•
: Uses unleaded solder.
5
6
7
8
KEY BOARD
A
3
S408
S407
R410
CD
V
OFF
Y
S402
R402
S409
R411
S403
1
R401
S403
EX-CHANGE
TUNING MODE
S407
RADIO/BAND
AUTO PRESET
R409
R408
R404
R403
S404
B
S406
TUNER/PRESET/
TRACK +
S406
11
OPEN/CLOSE
;
C
S402
TUNER/PRESET/
TRACK -
1-872-489-
JACK BOARD
(11)
MEGA BASS BOARD
VOL BOARD
S401
1
R424
3
R425
1
FB201
FB101
D
1
3
AUDIO IN
C207
C107
CN417
CN418
1
1
S416
3
ROTARY ENCODER
J301
AUDIO IN
FB301
E
VOLUME
S417
MEGA BASS
OFFU ON
3
(11)
6
6
11
11
1-872-492-
1
9
1
1-871-491-
11
(11)
1-872-490-
G
ICF-CDK70
27
27
MAIN BOARD
CN413
(Page 24)
(11)
ICF-CDK70
6-11. PRINTED WIRING BOARDS - POWER SUPPLY Section -
1
• See page 17 for Circuit Boards Location.
3
2
4
5
•
: Uses unleaded solder.
6
7
8
9
10
11
AMP BOARD
(CND)
11
1-872-483-
(11)
CONNECT TO
SHEET(SHIELD)
• Semiconductor
Location
Ref. No.
Location
D901
D902
D903
D904
D950
D952
D953
C-4
B-4
C-4
B-4
C-9
D-7
D-8
IC302
B-8
Q102
Q202
Q301
Q302
Q950
Q951
Q952
Q953
B-9
B-9
B-8
A-8
D-10
D-8
C-7
D-9
ICF-CDK70
28
28
C219
+
R120
R313
2
JW306
R968
E
R958
R957
R956
R953
R952
R951
K
B
C
Q953
E
B
C
Q950
MAIN
BOARD
(Page 24)
C954
+
C953
R967
Q951
B
H
1
R959
14
C316
R121 R119
A
C957
D950
K
K
CN301
C117
R314
JW301
E
C318
C123
13
C119
R128
JW302
R127
R125
R126 R124
C952
A
D953
+
C
R309
R954
R950
D952
CN904
A
R961
D
1
A
E
R955
C959
R962
2
B
R960
B
2
L901
C956
C
Q952
+
FH901
R129
C309
C228
C128
+
C903
C901
C951
BLK
C909
JW305
C950
JW901
F901
C125
JW304
CN901 1
FH902
C307
C908
D901
(US)
C310
C126
C127
+
4
C217
Q102
C122
+
D903
SP101
(L-CH)
7
R122
B
Q202
C
+
C
+
T901
POWER TRANSFORMER
TU BOARD
+
JW902
J
(Page 20)
R222
C
12
R130
C902
C904
2
1
CN902
1
SP201
(R-CH)
6
IC302
R230 CN303
C907
D902
JW303
WHT
(AC IN)
R227
E
+
D904
R221
+
+
Q301
R228
C
2
R229
L902
1
R220 R219
R225
C225
+
+
B C226
E
1
B
R226 R224
C
C311
+
CN903
C222
+
C227
C223
Q302
E
B
POWER BOARD
+
A
E
11
1-872-484-
(11)
ICF-CDK70
6-12. SCHEMATIC DIAGRAM - POWER SUPPLY Section -
• See page 30 for IC Block Diagrams.
Q301,302
Q301
RT1P441C-TP-1
POW_ON
Q302
RT1N141C-TP-1
STANDBY SWITCH
C311
470
16V
C225
47
10V
C223
2200
R221
22k
C222
1
50V
R220
4.7k
A_MUTE
R119
1k
R120
4.7k
GND
POWER
GND
STBY
BS R
POWER
CN303
4P
SP201
VCC
Q102
2SC3052EFT1-LEF
C119
4700p
L_CH
LIN+
IC302
ROUT
MUTING
POWER AMP
C117
1
50V
R230
2.2
R227
2.2k
BS L
C219
4700p
C226
100
10V
R226
0
Q102,202
C307
100
10V
R229
100
LOUT
R309
470
R224
4.7k
Q202
2SC3052EFT1-LEF
R222
100
R228
1k
RIN+
R219
1k
R NF
L NF
PRE GND
RIPPLE
R_CH
C217
1
50V
C228
0.22
C227
1000
10V
(R-CH)
R127
2.2k
R122
100
R124
4.7k
R121
22k
SP101
(L-CH)
R126
0
R125
220k
R225
220k
C310
47
10V
BUZZ
R313
10k
C316
4700p
R314
2.2k
C318
4700p
C122
1
50V
R128
1k
C126
100
10V
C127
1000
10V
R130
2.2
C128
0.22
C123
2200p
Q950
2SD2394-F
R129
100
C125
47
10V
C309
0.1
A_MUTE
A_MUTE
POW_ON
POW_ON
AGC
D-GND
(Page 23)
R960
100
2.2k
2.2k
1k
1k
R950
R962
R961
R954
10k
R959
47
D952
MA111-TX
Q952
2SC3052EF
-T1-LEF
C957
0.1
C956
100
10V
C953
470
10V
D950
UDZS-TE17
-6.8B
C952
0.01
R955
10k
C959
220
16V
6V
C903
0.01
C901
0.01
TRANSFORMER
D901
IN4002-B5
JW901
(US)
CN903
2P
GND
B+
VT
U-GND
D903
IN4002-B5
16V
R967
10
R968
10
T901
POWER
4700
BUZZ
F901
3.15A
125V
REGULATOR CONTROL
Q951
RT1P144C
-TP-1
0.01
L_CH
BUZZ
L901
C950
L_CH
(CND)
C951
A-GND
Q951,952
R951
R958
1k
2.2k
+6V REGULATOR
2.2k
R_CH
C954
0.1
R956
1k
R953
R_CH
R957
1k
Q953
2SD2394-F
CN301
14P
R952
+6V REGULATOR
CN901
2P
GND
D904
IN4002-B5
C909
0.01
C904
0.01
C908
47
25V
C902
0.01
D902
IN4002-B5
(AC IN)
L902
CN902
2P
B+
D953
MC2836
CN904
2P
TU-GND
C907
100p
(Page 21)
M-6V
M-GND
ICF-CDK70
29
29
ICF-CDK70
• Waveforms
Approx.
170 mVp-p
100 mV/DIV, 500 ns/DIV
IC701 FL (XO)
XB
3.4 Vp-p
1 V/DIV, 20 ns/DIV
IC701 BU9532KS2
IC801 RG (X1A)
52 51 50 49 48 47 46 45
44 43 42 41 40
3.2 Vp-p
0.9 Vp-p
30.6 Ms
13.3 Ms
1 V/DIV, 10 Ms/DIV
500 mV/DIV, 5 Ms/DIV
XT
59.1 ns
IC2 X (XOUT)
IC801 PT (X1)
AVDD1
AC
BD
VBIAS
E
F
PKC
FEN
FEO
BTC
3.3 Vp-p
240 ns
1 V/DIV, 100 ns/DIV
1
2
3
4
5
6
7
8
9
10
1 bit D/A
CONVERTER
RF SIGNAL
GENERATOR
39
38
37
DGND
XO
XI
36
35
34
33
32
31
30
29
28
27
DVDD
XPLCK
MONI1
MONI0
BUSY
RESETX
R/W
DOUT
DIN
MCK
x8 OVER
SAMPLING
DIGITAL
FILTER
PD 11
LD 12
IC701 SL (TEO)
(CD play mode)
COMMAND
INTERFACE
SERVO
SIGNAL
GENERATOR
APC
ASY 13
DIGITAL SERVO
SIGNAL
PROCESSOR
14 15
16
PCO
FCO
AGND1
PLL
Approx.
110 mVp-p
DIGITAL
SERVO
FILTER
DIGITAL
SIGNAL
PROCESSOR
16k SRAM
17 18 19 20 21 22
23 24 25 26
CLK88
LON
CLK
SUBSYQ
RB
AGND2
RDACO
VCDAC
LDACO
AVDD2
IC701 (FEO)
(CD play mode)
• IC Block Diagrams
- CD Board -
- MAIN Board -
FDOUT
JUMPO
TDOUT
SDIN
SDOUT
CLVOUT
- TU Board -
EQO
RFI
CAGC
TEN
TEO
SC
TZCRFM
RFRPRFM
- CD Board -
100 mV/DIV, 500 ns/DIV
IC702 BA5826SFP-E2
VO1(–)
1
VO1(+)
2
IN1
3
28 GND
D.BUFF
27 VO4(–)
D.BUFF
D.BUFF
LEVEL
SHIFT
26 VO4(+)
LEVEL
SHIFT
D.BUFF
25 IN4
RESET 4
24 IN4'
REGULATOR
THERMAL
SHUT-DOWN
REGULATOR
BIAS TRAP
REGB
23 BIAS
5
REGOUT 6
MUTE
7
GND
8
IN2'
9
MUTE
VCC
22 VCC
VCC
21 VCC
20 IN3'
19 IN3
IN2 10
D.BUFF
LEVEL
SHIFT
LEVEL
SHIFT
D.BUFF
18 VO3(+)
VO2(+) 11
VO2(–) 12
GND 13
OPOUT 14
ICF-CDK70
30
30
D.BUFF
D.BUFF
17 VO3(–)
16 RESETt
15 OPIN
ICF-CDK70
- TU Board IC1 TA2149BN
RF GND 1
24 FM RFOUT
FM RF
23 RF VCC
FM RFIN 2
22 AM RFIN
AM
MIX
AM LOW CUT 3
FM
OSC
FM
MIX
MIX OUT 4
AM IF
AM IF IN 6
1/1 OR
1/16
LEVEL
DET
ST
1/8
AM
DET
IF REQ
AF
QUAD 10
FM
DET
R-OUT 11
ST/MO
FM/AM
MUTE
18 ST LED
SW
AF BUFF
AGC
20 AM OSC
19 OSC OUT
IF BUFF
FM IF
GND 8
AGC 9
BUFF
BUFF
VCC 5
FM IF IN 7
21 FM OSC
AM
OSC
17 IF REQ
16 DET OUT
15
L-OUT 12
MPX IN
VCO
DIVIDE
14 LPF1
DECODE
13 LPF2
IC2 LC72137M-TLM-E
CE
DI
CL
DO
1
2
3
4
CCB
I/F
20 XOUT
19 XIN
B01
5
B02
6
B03
7
I01
8
I02
9
DATA SHIFT REGISTER
LATCH
REFERENCE
DIVIDER
12BITS
PROGRAMMABLE
DIVIDER
PHASE
DETECTOR
CHARGE
PUMP
18 AOUT
17 AIN
16 PD
15 VSS
UNLOCK
DETECTOR
POWER ON
RESET
14 VDD
13 B04
UNIVERSAL
COUNTER
SWALLOW
COUNTER
1/16,1/17
4BITS
1/2
12 FMIN
11 AMIN
IFIN 10
31
ICF-CDK70
- MAIN Board -
INR4
LOUT
ROUT
AGND
VCC
REFIN
DATA
CLK
DGND
TRER
TREL
NC
NC
BASSL2
IC301 R2S15904SP
28
27
26
25
24
23
22
21
20
19
18
17
16
15
TONE CONTROL
L-CH BASS/TREBLE
MCU
I/F
REF
MODE
SELECTOR
SURROUND
MUTE
MUTE
INL2
INL3
VOLUME
9
10
11
12
13
14
BASSL1
INL1
8
BASSR2
INR1
7
BASSR1
6
VOLINR
5
- AMP Board IC302 UTC8227 S
VCC1
OUTPUT1
BOOT STRAP1
PRE GND
NF1
INPUT1
32
1
2
3
4
5
6
+
–
–
+
CH-1
CH-2
12
11
10
9
8
7
TONE CONTROL
R-CH BASS/TREBLE
IGOUTR
4
VOLINL
3
IGOUTL
2
INL4
1
INR2
VOLUME
INPUT
SELECTOR
INR3
INPUT
SELECTOR
INPUT GAIN
CONTROL
INPUT GAIN
CONTROL
VCC2
OUTPUT2
BOOT STRAP2
RIPPLE
NF2
INPUT2
ICF-CDK70
• IC Pin Function Description
MAIN BOARD IC801 MB90802PF-G-124E1 (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
1
O-TU-DO
O
Serial data output to the FM/AM PLL
Description
2
O-TU-CE
O
Chip enable signal output to the FM/AM PLL
3
I-CD-LIMSW
I
Detection input from the sled limit-in detect switch
The optical pick-up is inner position when "L"
4
I-CD-BUSY
I
Busy signal input from the CD DSP
5
O-CD-DIN
O
Serial data output to the CD DSP
6
O-CD-MCK
O
Serial data transfer clock signal output to the CD DSP
7
I-CD-DOUT
I
Serial data input terminal
8
O-CD-RW
O
Data read/write selection signal output to the CD DSP
9
I-RMC
I
Remote control signal input from the remote control receiver
10
O-POWER CD
O
CD power on/off control signal output terminal
11
O-AMP STANDBY
O
Output control signal output to the power amplifier
12
O-4.5V CE
O
Not used
13
X0A
I
Sub system clock input terminal (32.768 kHz)
"L": active
"H": CD power on
14
X1A
O
Sub system clock output terminal (32.768 kHz)
15
VCC
-
Power supply terminal (+3.3V)
16
VSS
-
Ground terminal
17
O-CD-XRST
O
System reset signal output to the CD DSP
18
O-MO2-
O
Motor drive signal (-) output terminal for CAM rotation
19
O-MO2+
O
Motor drive signal (+) output terminal for CAM rotation
20
O-MO1-
O
Motor drive signal (-) output terminal for drawer movable
21
O-MO1+
O
Motor drive signal (+) output terminal for drawer movable
22
O-A MUTE
O
Audio muting on/off control signal output terminal
23
O-BUZZER
O
Buzzer drive signal output terminal
24
O-BASS BOOST OFF
O
Not used
25
I-TRSW3
I
CD switch (SW3) input terminal
26
I-TRSW1
I
CD switch (SW1) input terminal
27
I-TRSW7
I
CD chuck switch (SW7) input terminal
28
I-TRSW2
I
CD switch (SW2) input terminal
29
I-TRSW6
I
CD close switch (SW6) input terminal
30
I-TRSW5
I
CD stock switch (SW5) input terminal
31
I-TRSW8
I
CD open switch (SW8) input terminal
32
AVCC
-
Power supply terminal (+3.3V) (for A/D converter)
33
O-VOL-DATA
O
Serial data output to the electrical volume
34
O-VOL-CLK
O
Serial data transfer clock signal output to the electrical volume
35
AVSS
-
Ground terminal (for A/D converter)
36
I-REG6.0V-CHK
I
Input terminal for +6V power supply voltage detection
37
I-REG4.5V-CHK
I
Input terminal for +4.5V power supply voltage detection
38 to 40
I-KEY0 to I-KEY2
I
Front panel key input terminal (A/D input)
41
I-REG3.3V-CHK
I
Input terminal for CD +3.3V power supply voltage detection
42
I-AC IN
I
Not used
43
I-CD-SUBSYQ
I
Subcode Q data (80 bit serial) input from the CD DSP
44
VSS
-
Ground terminal
I
Input terminal for destination discrimination
I
MEGA BASS switch input terminal
I
Jog dial pulse input from the rotary encoder (VOLUME)
45 to 47
48
49, 50
51 to 53
I-SUFFIX 0 to
I-SUFFIX 2
I-BASS BOOST ON/
OFF
I-ENCODER +,
I-ENCODER MD2 to MD0
"L": reset
"H": muting on
"L": MEGA BASS on, "H": MEGA BASS off
I
Input terminal for flash writing mode setting
54
I-RESET
I
System reset signal input from the reset signal generator "L": reset
For several hundreds msec. after the power supply rises, "L" is input, then it changes to "H"
55 to 57
O-DISC1KEY LED to
O-DISC3KEY LED
O
LED drive signal output terminal
58
VLCD
I
Input terminal for liquid crystal display drive voltage setting
59 to 62
COM4 to COM1
O
Common drive signal output to the liquid crystal display
33
ICF-CDK70
Pin No.
Pin Name
I/O
63, 64
SEG0, SEG1
O
Segment drive signal output to the liquid crystal display
Description
65
VCC
-
Power supply terminal (+3.3V)
66
VSS
-
Ground terminal
67 to 81
SEG2 to SEG16
O
Segment drive signal output to the liquid crystal display
82 to 84
NC
O
Not used
85
O-TIMER LED
O
LED drive signal output terminal
86, 87
I-ENCODER-TIMER+,
I-ENCODER-TIMER-
I
Jog dial pulse input from the rotary encoder (TIMER)
88, 89
NC
O
Not used
90
VCC
-
Power supply terminal (+3.3V)
91
VSS
-
Ground terminal
92
X1
O
Main system clock output terminal (4.19 MHz)
93
X0
I
Main system clock input terminal (4.19 MHz)
94
O-CLK-SHIFT AM
O
Oscillation frequency selection on/off control signal output terminal for AM
"H": selection on
95
O-CLK-SHIFT FM
O
Oscillation frequency selection on/off control signal output terminal for FM
"H": selection on
96
O-POWER AUDIO IN
O
Not used
97
O-POWER TUNER
O
Tuner power on/off control signal output terminal
98
O-TU-MUTE
O
Tuner muting on/off control signal output to the FM/AM PLL
99
I-TU-DI
I
Serial data input to the FM/AM PLL
100
O-TU-CLK
O
Serial data transfer clock signal output to the FM/AM PLL
34
"H": power on
"H": muting on
ICF-CDK70
SECTION 7
EXPLODED VIEWS
Note:
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
• Accessories are given in the last of the
electircal parts list.
7-1.
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Color Indication of Appearance Parts Example:
KNOB, BALANCE (WHITE) . . . (RED)
R
R
Parts of Color Cabinet’s Color
• Abbreviation
CND: Canadian model
The components identified by mark 0
or dotted line with mark 0 are critical for
safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
CABINET (UPPER) SECTION
3
3
3
3
5
3
13
4
13
2
2
3
3
13
6
12
8
10
1
13
2
7
9
CD mechanism deck section
(DLM3A23-11)
2
8
cabinet (front) section
11
cabinet (lower) section
11
Ref. No.
Part No.
Description
1
2
3
4
5
2-893-517-01
3-254-151-01
3-254-140-01
3-252-831-01
2-893-513-01
COVER (TRAY)
SCREW (B2.6), (+) P TAPPING
SCREW (B2.6), (+) BV TAPPING
SCREW (M2.6), (+) P
CABINET (UPPER) (US)
5
6
2-893-513-11
2-893-490-01
CABINET (UPPER) (CND)
KNOB (MEGA BASS)
Remark
Ref. No.
Part No.
Description
7
8
9
A-1224-512-A
3-254-081-01
2-893-521-01
JACK BOARD, COMPLETE
SCREW
HOLDER (AUDIO IN)
10
11
12
13
A-1224-514-A
3-254-070-01
3-208-071-01
3-208-071-11
MEGA BASS BOARD, COMPLETE
SCREW
CUSHION (SP BOX)
CUSHION (SP BOX)
Remark
35
ICF-CDK70
Ver. 1.1
7-2.
CABINET (FRONT) SECTION
64
65
67
TIMER board
66
76
75
57
64
64
54
LCD board
not supplied
61
72
59 60
not supplied
62
64
LCD401
53
63
54
70
69
64
58
68
74
64
72
72
56
72
64
51
73
71
72
52
54
73
not supplied
55
73
54
not supplied
72
Ref. No.
73
Part No.
Description
51
52
53
54
55
X-2177-115-1
2-896-916-01
2-893-489-01
3-254-070-01
2-893-488-01
CABINET (FRONT) SUB ASSY
CUSHION (A)
KNOB (ALARM)
SCREW
KNOB (VOL)
56
57
58
59
60
2-637-764-01
A-1224-496-A
2-893-506-01
2-896-914-01
2-893-495-01
CUSHION (TRAY)
LCD BOARD, COMPLETE
CASE (LCD), SHIELD
SHEET, DIFFUSION
PLATE (LCD), LIGHT GUIDE
61
62
63
64
2-893-522-01
1-833-883-21
1-833-882-21
3-254-081-01
HOLDER (LCD)
CABLE, FLEXIBLE FLAT (14 CORE)
CABLE, FLEXIBLE FLAT (12 CORE)
SCREW
36
Remark
Ref. No.
Part No.
Description
65
A-1224-501-A
TIMER BOARD, COMPLETE
Remark
66
67
68
69
70
1-833-902-21
2-893-520-01
2-893-519-01
A-1224-506-A
1-831-772-21
CABLE, FLEXIBLE FLAT (4 CORE)
HOLDER (ALARM)
HOLDER (VOL)
VOL BOARD, COMPLETE
CABLE, FLEXIBLE FLAT (9 CORE)
71
72
73
74
75
A-1224-508-A
3-885-228-01
3-577-414-01
3-097-771-01
3-208-071-01
KEY BOARD, COMPLETE
CUSHION (B)
SPACER
SHEET (B), LIGHT INTERCEPTION
SHEET (LCD)
76
LCD401
A-1224-499-A
1-802-382-11
REMOTE CONTROL BOARD, COMPLETE
DISPLAY PANEL, LIQUID CRYSTAL
ICF-CDK70
7-3.
CABINET (LOWER) SECTION
102
109
107
not supplied
110
102
(CND)
106
108
107
F901
MAIN board
107
111
102
116
102
not supplied
SP101
104
#1
T901
102
113
112
not
supplied
105
#1
102
102
114
not supplied
not supplied
102
102
CD lid assy section
AMP board
not supplied
102
116
101
102
not supplied
104
102
103
Ref. No.
115
SP201
Part No.
Description
101
101
102
103
103
X-2177-112-1
X-2177-113-1
3-254-151-01
2-893-497-01
2-893-497-11
CABINET (LOWER) SUB ASSY (US)
CABINET (LOWER) SUB ASSY (CND)
SCREW (B2.6), (+) P TAPPING
SP BOX (R) (US)
SP BOX (R) (CND)
104
105
105
106
107
3-885-228-01
2-893-496-01
2-893-496-11
A-1109-056-A
3-252-827-01
CUSHION (B)
SP BOX (L) (US)
SP BOX (L) (CND)
TU BOARD, COMPLETE
SCREW (B2.6), (+) BV TAPPING
108
109
110
2-896-915-01
A-1224-485-A
1-832-425-21
SHEET (BLIND A)
MAIN BOARD, COMPLETE
CABLE, FLEXIBLE FLAT (11 CORE)
Remark
Ref. No.
Part No.
Description
Remark
111
112
1-832-052-21
3-100-562-01
CABLE, FLEXIBLE FLAT (14 CORE)
SHEET (SHIELD)
113
113
0 114
115
116
A-1224-482-A
A-1225-192-A
1-828-104-31
A-1224-478-A
3-208-071-21
POWER BOARD, COMPLETE (US)
POWER BOARD, COMPLETE (CND)
CORD, POWER
AMP BOARD, COMPLETE
CUSHION (SP BOX)
0 F901
SP101
SP201
0 T901
#1
1-533-451-12
1-826-605-11
1-826-605-11
1-435-917-22
7-684-025-04
FUSE, GLASS TUBE (DIA. 5) (3.15A/125V) (CND)
SPEAKER (6.6 cm) (L-CH)
SPEAKER (6.6 cm) (R-CH)
TRANSFORMER, POWER
N 5, TYPE 2
37
ICF-CDK70
7-4.
CD LID ASSY SECTION
157
155
158
159
153
155
156
160
156
152
161
LED board
154
151
Ref. No.
Part No.
Description
151
152
153
154
155
X-2177-114-1
3-573-007-01
A-1224-490-A
1-833-880-21
3-254-070-01
LID (FRONT) SUB ASSY, CD
SHEET (1)
LED BOARD, COMPLETE
CABLE, FLEXIBLE FLAT (6 CORE)
SCREW
156
2-896-916-01
CUSHION (A)
38
Remark
Ref. No.
Part No.
Description
157
158
159
160
2-893-491-01
2-893-510-01
2-893-516-01
2-893-511-01
LEVER (SHAFT L)
SPRING (ARM L)
LID (REAR), CD
SPRING (ARM R)
161
2-893-492-01
LEVER (SHAFT R)
Remark
ICF-CDK70
7-5.
CD MECHANISM DECK SECTION
(DLM3A23-11)
not supplied
not supplied
205
not supplied
not supplied
208
208
212
not supplied
not supplied
212
204
203
not supplied
202
207
212
not supplied
204
211
212
204
203
203
202
202
204
203
202
206
201
210
#5
Ref. No.
Part No.
Description
201
202
203
204
205
A-1226-316-A
4-985-672-01
4-227-045-31
4-227-549-11
1-797-193-12
CD BOARD, COMPLETE
SCREW (+PTPWHM2.6), FLOATING
SPRING (INSULATOR), COIL
INSULATOR
MECHANICAL, CD (DLM3A23-11)
206
1-832-025-21
CABLE, FLEXIBLE FLAT (16 CORE)
Remark
Ref. No.
Part No.
Description
Remark
0 207
208
210
211
8-820-070-07
2-632-062-11
1-833-881-21
1-832-836-21
OPTICAL PICK-UP BLOCK (KSM-213CCP/C2NP)
BELT (DLM3A)
CABLE, FLEXIBLE FLAT (14 CORE)
CABLE, FLEXIBLE FLAT (13 CORE)
212
#5
3-254-143-01
7-685-853-04
SCREW (B3), (+) BV TAPPING
SCREW +BVTT 2X6 (S)
39
ICF-CDK70
SECTION 8
ELECTRICAL PARTS LIST
AMP
Note:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the components used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
• CAPACITORS
uF: µF
• COILS
uH: µH
Ref. No.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. . , uPA. . , µPA. . ,
uPB. . : µPB. . , uPC. . , µPC. . ,
uPD. . : µPD. .
• Abbreviation
CND : Canadian model
Part No.
Description
A-1224-478-A
AMP BOARD, COMPLETE
********************
Remark
3-254-151-01
SCREW (B2.6), (+) P TAPPING
Ref. No.
Part No.
When indicating parts by reference number, please include the board name.
The components identified by mark 0
or dotted line with mark 0 are critical for
safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
Description
Remark
< IC >
IC302
6-710-261-01
IC UTC8227 S
< TRANSISTOR >
< CAPACITOR >
C117
C119
C122
C123
C125
1-126-960-11
1-162-968-11
1-126-960-11
1-162-966-11
1-126-947-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
1uF
0.0047uF
1uF
0.0022uF
47uF
20%
10%
20%
10%
20%
50V
50V
50V
50V
35V
C126
C127
C128
C217
C219
1-104-665-11
1-126-926-11
1-127-715-11
1-126-960-11
1-162-968-11
ELECT
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
100uF
1000uF
0.22uF
1uF
0.0047uF
20%
20%
10%
20%
10%
25V
10V
16V
50V
50V
C222
C223
C225
C226
C227
1-126-960-11
1-162-966-11
1-126-947-11
1-104-665-11
1-126-926-11
ELECT
CERAMIC CHIP
ELECT
ELECT
ELECT
1uF
0.0022uF
47uF
100uF
1000uF
20%
10%
20%
20%
20%
50V
50V
35V
25V
10V
C228
C307
C309
C310
C311
1-127-715-11
1-104-665-11
1-107-826-11
1-126-947-11
1-126-935-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
ELECT
0.22uF
100uF
0.1uF
47uF
470uF
10%
20%
10%
20%
20%
16V
25V
16V
35V
16V
C316
C318
C950
C951
C952
1-162-968-11
1-162-968-11
1-126-937-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.0047uF
0.0047uF
4700uF
0.01uF
0.01uF
10%
10%
20%
10%
10%
50V
50V
16V
25V
25V
C953
C954
C956
C957
C959
1-126-935-11
1-107-826-11
1-104-665-11
1-107-826-11
1-126-934-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
470uF
0.1uF
100uF
0.1uF
220uF
20%
10%
20%
10%
20%
16V
16V
25V
16V
16V
< CONNECTOR >
CN301
CN303
CN903
1-784-775-11
1-815-445-11
1-815-443-11
CONNECTOR, FFC 14P
PIN, CONNECTOR (PWB) 4P
PIN, CONNECTOR (PWB) 2P
< DIODE >
D950
D952
D953
40
8-719-978-33
8-719-404-50
6-500-334-01
DIODE DTZ-TT11-6.8B
DIODE MA111-TX
DIODE MC2836-T112-1
Q102
Q202
Q301
Q302
Q950
8-729-120-28
8-729-120-28
8-729-027-38
8-729-027-43
8-729-018-99
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC1623-L5L6
2SC1623-L5L6
DTA144EKA-T146
DTC114EKA-T146
2SD2394-F
Q951
Q952
Q953
8-729-027-26
8-729-120-28
8-729-018-99
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTA114YKA-T146
2SC1623-L5L6
2SD2394-F
< RESISTOR >
R119
R120
R121
R122
R124
1-216-821-11
1-216-829-11
1-216-837-11
1-216-809-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
4.7K
22K
100
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R125
R126
R127
R128
R129
1-216-849-11
1-216-864-11
1-216-825-11
1-216-821-11
1-216-809-11
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220K
0
2.2K
1K
100
5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
R130
R219
R220
R221
R222
1-216-789-11
1-216-821-11
1-216-829-11
1-216-837-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2
1K
4.7K
22K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R224
R225
R226
R227
R228
1-216-829-11
1-216-849-11
1-216-864-11
1-216-825-11
1-216-821-11
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
4.7K
220K
0
2.2K
1K
5%
5%
1/10W
1/10W
5%
5%
1/10W
1/10W
R229
R230
R309
R313
R314
1-216-809-11
1-216-789-11
1-216-817-11
1-216-833-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
2.2
470
10K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R950
R951
R952
R953
R954
1-216-825-11
1-216-825-11
1-216-825-11
1-216-825-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
2.2K
2.2K
2.2K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
ICF-CDK70
AMP
Ref. No.
R955
R956
R957
R958
R959
Part No.
Description
1-216-833-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-805-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
Remark
10K
1K
1K
1K
47
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R960
1-216-809-11 METAL CHIP
100
5%
1/10W
R961
1-216-821-11 METAL CHIP
1K
5%
1/10W
R962
1-216-821-11 METAL CHIP
1K
5%
1/10W
R967
1-216-797-11 METAL CHIP
10
5%
1/10W
R968
1-216-797-11 METAL CHIP
10
5%
1/10W
************************************************************
A-1226-316-A
CD BOARD, COMPLETE
*******************
< CAPACITOR >
C701
C702
C703
C704
C705
1-107-826-11
1-104-665-11
1-125-837-11
1-104-665-11
1-125-837-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.1uF
100uF
1uF
100uF
1uF
10%
20%
10%
20%
10%
16V
25V
6.3V
25V
6.3V
C706
C707
C708
C710
C711
1-104-665-11
1-104-665-11
1-107-826-11
1-162-927-11
1-162-919-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
100uF
0.1uF
100PF
22PF
20%
20%
10%
5%
5%
25V
25V
16V
50V
50V
C712
C713
C714
C716
C717
1-164-230-11
1-162-970-11
1-107-826-11
1-126-963-11
1-127-715-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
220PF
0.01uF
0.1uF
4.7uF
0.22uF
5%
10%
10%
20%
10%
50V
25V
16V
50V
16V
C718
C719
C720
C721
C722
1-125-837-11
1-125-837-11
1-127-715-11
1-126-964-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
1uF
1uF
0.22uF
10uF
0.1uF
10%
10%
10%
20%
10%
6.3V
6.3V
16V
50V
16V
C723
C724
C725
C726
C727
1-125-837-11
1-125-837-11
1-162-964-11
1-162-919-11
1-162-919-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
0.001uF
22PF
22PF
10%
10%
10%
5%
5%
6.3V
6.3V
50V
50V
50V
C728
C729
C731
C732
C733
1-162-919-11
1-162-927-11
1-162-970-11
1-162-964-11
1-104-665-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
22PF
100PF
0.01uF
0.001uF
100uF
5%
5%
10%
10%
20%
50V
50V
25V
50V
25V
C734
C738
C739
C740
C741
1-162-970-11
1-126-935-11
1-104-665-11
1-107-826-11
1-125-837-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.01uF
470uF
100uF
0.1uF
1uF
10%
20%
20%
10%
10%
25V
16V
25V
16V
6.3V
C742
C743
C744
C745
C746
1-162-966-11
1-162-964-11
1-162-966-11
1-162-964-11
1-162-966-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF
0.001uF
0.0022uF
0.001uF
0.0022uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C747
C748
C749
C750
C751
1-162-966-11
1-125-837-11
1-162-927-11
1-162-923-11
1-162-966-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF
1uF
100PF
47PF
0.0022uF
10%
10%
5%
5%
10%
50V
6.3V
50V
50V
50V
Ref. No.
CD
Part No.
Description
C753
C754
C755
C756
C757
1-162-927-11
1-164-230-11
1-125-837-11
1-162-919-11
1-162-923-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
220PF
1uF
22PF
47PF
5%
5%
10%
5%
5%
50V
50V
6.3V
50V
50V
Remark
C758
C760
C761
C762
C763
1-165-176-11
1-127-692-11
1-104-665-11
1-107-826-11
1-125-837-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.047uF
10uF
100uF
0.1uF
1uF
10%
10%
20%
10%
10%
16V
16V
25V
16V
6.3V
C764
C765
C767
C768
C769
1-126-934-11
1-162-923-11
1-162-966-11
1-162-964-11
1-126-964-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
220uF
47PF
0.0022uF
0.001uF
10uF
20%
5%
10%
10%
20%
16V
50V
50V
50V
50V
C770
C771
C772
C774
1-162-970-11
1-125-837-11
1-125-837-11
1-125-837-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
1uF
1uF
1uF
10%
10%
10%
10%
25V
6.3V
6.3V
6.3V
< CONNECTOR >
CNP701 1-779-553-21
CNP702 1-784-736-11
CONNECTOR, FFC (LIF (NON-ZIF)) 16P
CONNECTOR, FFC 14P
< DIODE >
D701
D702
8-719-404-50
8-719-404-50
DIODE MA111-TX
DIODE MA111-TX
< JUMPER RESISTOR/FERRITE BEAD >
FB701
FB702
FB703
FB704
1-216-295-00
1-216-295-00
1-216-295-00
1-500-445-21
SHORT CHIP
0
SHORT CHIP
0
SHORT CHIP
0
FERRITE, EMI (SMD) (2012)
< IC >
IC701
IC702
6-708-984-01
6-710-637-01
IC BU9532KS2
IC BA5826SFP-E2
< JUMPER RESISTOR >
JC701
JC702
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
0
0
< TRANSISTOR >
Q701
Q702
Q703
Q704
8-729-600-22
8-729-120-28
8-729-120-28
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1235-F
2SC1623-L5L6
2SC1623-L5L6
2SC1623-L5L6
< RESISTOR >
R701
R702
R703
R704
R705
1-216-837-11
1-216-833-11
1-216-837-11
1-216-837-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
10K
22K
22K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R706
R707
R708
R709
R710
1-216-833-11
1-216-837-11
1-216-833-11
1-216-837-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
22K
10K
22K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R711
1-216-809-11
METAL CHIP
100
5%
1/10W
41
ICF-CDK70
CD
Ref. No.
JACK
KEY
LCD
Part No.
Description
R713
R714
R715
R716
1-216-793-11
1-216-793-11
1-216-845-11
1-216-853-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7
4.7
100K
470K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
Remark
R718
R719
R720
R721
R722
1-216-841-11
1-216-841-11
1-216-864-11
1-216-821-11
1-216-813-11
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
47K
47K
0
1K
220
5%
5%
1/10W
1/10W
5%
5%
1/10W
1/10W
R723
R724
R725
R726
R727
1-216-841-11
1-216-845-11
1-216-841-11
1-216-829-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
100K
47K
4.7K
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R728
R729
R730
R731
R732
1-216-837-11
1-216-837-11
1-216-845-11
1-216-825-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
22K
100K
2.2K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R733
R734
R735
R736
R737
1-216-837-11
1-216-841-11
1-216-829-11
1-216-825-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
47K
4.7K
2.2K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R738
R739
R740
R741
R742
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R743
R744
R745
R746
R747
1-216-825-11
1-216-809-11
1-216-864-11
1-216-837-11
1-216-817-11
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
2.2K
100
0
22K
470
5%
5%
1/10W
1/10W
5%
5%
1/10W
1/10W
R748
R749
R750
R751
R752
1-216-853-11
1-216-817-11
1-216-817-11
1-216-817-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470K
470
470
470
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R753
R754
R755
R756
R757
1-216-841-11
1-216-841-11
1-216-841-11
1-216-837-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
47K
47K
22K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R758
R760
R761
R762
R763
1-216-833-11
1-216-821-11
1-216-821-11
1-216-837-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
1K
22K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R764
R765
R766
R767
R768
1-216-825-11
1-216-821-11
1-216-841-11
1-216-817-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
1K
47K
470
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R769
R770
R771
R773
R774
1-216-833-11
1-216-821-11
1-216-849-11
1-216-833-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
220K
10K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R775
1-216-833-11
METAL CHIP
10K
5%
1/10W
Ref. No.
R776
R777
R778
Part No.
Description
1-216-833-11
1-216-833-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
Remark
10K
10K
47K
5%
5%
5%
1/10W
1/10W
1/10W
< SWITCH >
S701
1-572-085-21
SWITCH, LEAF (LIMIT)
< VIBRATOR >
X701
1-795-563-21 VIBRATOR, CERAMIC (16.9344MHz)
************************************************************
A-1224-512-A
JACK BOARD, COMPLETE
********************
< CAPACITOR >
42
C107
C207
1-162-964-11
1-162-964-11
CERAMIC CHIP 0.001uF
CERAMIC CHIP 0.001uF
10%
10%
50V
50V
< FERRITE BEAD >
FB101
FB201
FB301
1-414-445-11
1-414-445-11
1-414-445-11
FERRITE, EMI (SMD) (1608)
FERRITE, EMI (SMD) (1608)
FERRITE, EMI (SMD) (1608)
< JACK >
J301
1-566-822-51 JACK (AUDIO IN)
************************************************************
A-1224-508-A
KEY BOARD, COMPLETE
*******************
< RESISTOR >
R401
R402
R403
R404
R408
1-216-813-11
1-216-817-11
1-216-821-11
1-216-821-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
470
1K
1K
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R409
R410
R411
1-216-817-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
470
1K
1K
5%
5%
5%
1/10W
1/10W
1/10W
< SWITCH >
S402
1-786-050-21
S403
1-786-050-21
S404
S406
1-786-050-21
1-786-050-21
S407
1-786-050-21
SWITCH, KEY BOARD
(., TUNER/PRESET/TRACK –)
SWITCH, KEY BOARD
(EX-CHANGE, TUNING MODE)
SWITCH, KEY BOARD (OPEN/CLOSE, Z)
SWITCH, KEY BOARD
(>, TUNER/PRESET/TRACK +)
SWITCH, KEY BOARD
(RADIO/BAND, AUTO PRESET)
S408
1-786-050-21 SWITCH, KEY BOARD (OFF, x)
S409
1-786-050-21 SWITCH, KEY BOARD (CD u)
************************************************************
A-1224-496-A
LCD BOARD, COMPLETE
********************
2-893-495-01
2-893-506-01
2-893-522-01
2-896-914-01
PLATE (LCD), LIGHT GUIDE
CASE (LCD), SHIELD
HOLDER (LCD)
SHEET, DIFFUSION
ICF-CDK70
LCD
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
LED
Description
MAIN
Remark
< LED >
< CAPACITOR >
D404
6-501-553-01
LED 1L341Y22C0MA801 (LCD BACK LIGHT)
< LIQUID CRYSTAL DISPLAY >
LCD401
1-802-382-11
DISPLAY PANEL, LIQUID CRYSTAL
C101
C102
C103
C104
C105
1-126-160-11
1-126-160-11
1-162-964-11
1-126-160-11
1-126-160-11
ELECT
ELECT
CERAMIC CHIP
ELECT
ELECT
1uF
1uF
0.001uF
1uF
1uF
20%
20%
10%
20%
20%
50V
50V
50V
50V
50V
C106
C108
C109
C110
C111
1-162-964-11
1-126-160-11
1-162-927-11
1-126-163-11
1-165-176-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.001uF
1uF
100PF
4.7uF
0.047uF
10%
20%
5%
20%
10%
50V
50V
50V
50V
16V
C112
C113
C115
C116
C201
1-164-227-11
1-107-826-11
1-164-315-11
1-164-230-11
1-126-160-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.022uF
0.1uF
470PF
220PF
1uF
10%
10%
5%
5%
20%
25V
16V
50V
50V
50V
C202
C203
C204
C205
C206
1-126-160-11
1-162-964-11
1-126-160-11
1-126-160-11
1-162-964-11
ELECT
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
1uF
0.001uF
1uF
1uF
0.001uF
20%
10%
20%
20%
10%
50V
50V
50V
50V
50V
C208
C209
C210
C211
C212
1-126-160-11
1-162-927-11
1-126-163-11
1-165-176-11
1-164-227-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
1uF
100PF
4.7uF
0.047uF
0.022uF
20%
5%
20%
10%
10%
50V
50V
50V
16V
25V
C213
C215
C216
C301
C302
1-107-826-11
1-164-315-11
1-164-230-11
1-124-584-00
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.1uF
470PF
220PF
100uF
0.1uF
10%
5%
5%
20%
10%
16V
50V
50V
10V
16V
C303
C304
C305
C314
C319
1-124-589-11
1-162-923-11
1-162-923-11
1-162-970-11
1-162-970-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
47PF
47PF
0.01uF
0.01uF
20%
5%
5%
10%
10%
16V
50V
50V
25V
25V
C320
C350
C351
C352
C353
1-162-970-11
1-164-156-11
1-164-156-11
1-107-826-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
0.1uF
0.1uF
0.01uF
10%
10%
10%
25V
25V
25V
16V
25V
C354
C401
C402
C403
C801
1-126-934-11
1-162-927-11
1-162-927-11
1-162-927-11
1-162-927-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220uF
100PF
100PF
100PF
100PF
20%
5%
5%
5%
5%
16V
50V
50V
50V
50V
C802
C803
C804
C807
C809
1-162-927-11
1-162-927-11
1-162-927-11
1-162-915-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
100PF
10PF
100PF
5%
5%
5%
0.5PF
5%
50V
50V
50V
50V
50V
C810
C811
C812
C813
C814
1-162-927-11
1-162-927-11
1-162-927-11
1-162-919-11
1-162-919-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
100PF
22PF
22PF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C815
C816
C818
1-162-923-11
1-162-927-11
1-162-927-11
CERAMIC CHIP 47PF
CERAMIC CHIP 100PF
CERAMIC CHIP 100PF
5%
5%
5%
50V
50V
50V
< TRANSISTOR >
Q404
8-729-120-28
TRANSISTOR
2SC1623-L5L6
< RESISTOR >
R417
R418
R422
R423
R430
1-216-829-11
1-216-837-11
1-216-817-11
1-216-813-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
22K
470
220
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R431
1-216-817-11 METAL CHIP
470
5%
1/10W
************************************************************
A-1224-490-A
LED BOARD, COMPLETE
*******************
1-833-880-21
CABLE, FLEXIBLE FLAT (6 CORE)
< LED >
D401
D402
D403
6-501-553-01
6-501-553-01
6-501-553-01
LED 1L341Y22C0MA801 (1)
LED 1L341Y22C0MA801 (2)
LED 1L341Y22C0MA801 (3)
< TRANSISTOR >
Q401
Q402
Q403
8-729-120-28
8-729-120-28
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC1623-L5L6
2SC1623-L5L6
2SC1623-L5L6
< RESISTOR >
R412
R413
R414
R434
R435
1-216-813-11
1-216-817-11
1-216-821-11
1-216-817-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
470
1K
470
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R436
R437
R438
R439
R482
1-216-817-11
1-216-821-11
1-216-817-11
1-216-821-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
1K
470
1K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R483
R484
R485
R486
R487
1-216-829-11
1-216-837-11
1-216-829-11
1-216-837-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
22K
4.7K
22K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< SWITCH >
S410
1-771-349-21 SWITCH, KEY BOARD (1)
S411
1-771-349-21 SWITCH, KEY BOARD (2)
S412
1-771-349-21 SWITCH, KEY BOARD (3)
************************************************************
A-1224-485-A
MAIN BOARD, COMPLETE
********************
1-832-052-21
1-832-425-21
CABLE, FLEXIBLE FLAT (14 CORE)
CABLE, FLEXIBLE FLAT (11 CORE)
43
ICF-CDK70
MAIN
Ref. No.
Part No.
Description
C819
C820
1-162-964-11
1-162-964-11
CERAMIC CHIP 0.001uF
CERAMIC CHIP 0.001uF
10%
10%
50V
50V
Remark
Ref. No.
Part No.
Description
Remark
C821
C822
C823
C824
C825
1-162-964-11
1-162-964-11
1-162-964-11
1-162-964-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
CN305
CN401
CN402
CN409
CN411
1-784-774-11
1-784-734-11
1-784-736-11
1-784-726-11
1-784-767-11
CONNECTOR, FFC 13P
CONNECTOR, FFC 12P
CONNECTOR, FFC 14P
CONNECTOR, FFC 4P
CONNECTOR, FFC 6P
C826
C827
C830
C831
C832
1-162-915-11
1-162-915-11
1-162-927-11
1-162-927-11
1-162-923-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10PF
10PF
100PF
100PF
47PF
0.5PF
0.5PF
5%
5%
5%
50V
50V
50V
50V
50V
CN413
CN801
1-568-828-11
1-784-736-11
CONNECTOR, FFC 9P
CONNECTOR, FFC 14P
C833
C834
C835
C836
C837
1-162-908-11
1-162-923-11
1-162-970-11
1-162-923-11
1-162-908-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
3PF
47PF
0.01uF
47PF
3PF
0.25PF
5%
10%
5%
0.25PF
50V
50V
25V
50V
50V
C838
C839
C840
C841
C842
1-162-923-11
1-162-970-11
1-162-919-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47PF
0.01uF
22PF
100PF
100PF
5%
10%
5%
5%
5%
50V
25V
50V
50V
50V
C843
C844
C845
C847
C848
1-162-927-11
1-107-826-11
1-162-927-11
1-162-915-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
0.1uF
100PF
10PF
100PF
5%
10%
5%
0.5PF
5%
50V
16V
50V
50V
50V
C849
C854
C855
C856
C857
1-162-915-11
1-107-826-11
1-162-927-11
1-107-826-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10PF
0.1uF
100PF
0.1uF
100PF
0.5PF
10%
5%
10%
5%
50V
16V
50V
16V
50V
C858
C861
C862
C863
C864
1-162-927-11
1-162-927-11
1-165-908-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
1uF
100PF
100PF
5%
5%
10%
5%
5%
50V
50V
10V
50V
50V
C865
C866
C867
C868
C869
1-162-927-11
1-162-927-11
1-162-964-11
1-162-964-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
0.001uF
0.001uF
0.001uF
5%
5%
10%
10%
10%
50V
50V
50V
50V
50V
C880
C881
C882
C883
C884
1-124-584-00
1-162-970-11
1-162-970-11
1-124-584-00
1-162-970-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
100uF
0.01uF
0.01uF
100uF
0.01uF
20%
10%
10%
20%
10%
10V
25V
25V
10V
25V
C885
C886
C887
C888
C889
1-162-970-11
1-126-934-11
1-165-908-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
220uF
1uF
0.01uF
0.01uF
10%
20%
10%
10%
10%
25V
16V
10V
25V
25V
C890
C891
C894
C896
C897
1-107-826-11
1-107-826-11
1-165-908-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
1uF
100PF
100PF
10%
10%
10%
5%
5%
16V
16V
10V
50V
50V
C960
C961
C962
1-162-970-11
1-126-934-11
1-107-826-11
CERAMIC CHIP 0.01uF
ELECT
220uF
CERAMIC CHIP 0.1uF
10%
20%
10%
25V
16V
16V
< CONNECTOR >
< DIODE >
D307
D308
D309
D951
8-719-404-50
8-719-404-50
8-719-404-50
8-719-083-58
DIODE
DIODE
DIODE
DIODE
MA111-TX
MA111-TX
MA111-TX
UDZSTE-173.9B
< IC >
IC301
IC801
IC802
IC803
6-710-289-01
6-807-357-01
6-704-118-01
6-703-285-01
IC
IC
IC
IC
R2S15904SP
MB90802PF-G-124E1
S-80828CNMC-B8NT2G
S-812C33AUA-C2NT2G
< JUMPER RESISTOR >
44
JC101
JC201
JC802
JC804
JC805
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
< COIL >
L801
L802
L803
L804
L805
1-410-509-11
1-410-517-11
1-414-142-11
1-410-517-11
1-410-517-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
10uH
47uH
1uH
47uH
47uH
L806
L807
1-410-517-11
1-414-142-11
INDUCTOR
INDUCTOR
47uH
1uH
< TRANSISTOR >
Q350
Q351
Q352
Q353
Q354
8-729-047-62
8-729-047-62
8-729-047-62
8-729-047-62
8-729-024-43
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC3440-T12-1F
2SC3440-T12-1F
2SC3440-T12-1F
2SC3440-T12-1F
2SA1365-T112-1EF
Q355
Q356
Q357
Q358
Q359
8-729-024-43
8-729-024-43
8-729-024-43
8-729-040-76
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1365-T112-1EF
2SA1365-T112-1EF
2SA1365-T112-1EF
KTA1273-Y-AT
2SC1623-L5L6
Q360
Q361
Q362
Q801
Q802
8-729-600-22
8-729-600-22
8-729-120-28
8-729-120-28
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1235-F
2SA1235-F
2SC1623-L5L6
2SC1623-L5L6
2SC1623-L5L6
Q803
Q804
Q805
Q954
Q955
8-729-027-46
8-729-027-26
8-729-027-46
8-729-028-54
8-729-027-26
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114YKA-T146
DTA114YKA-T146
DTC114YKA-T146
KTC3205
DTA114YKA-T146
Q956
8-729-027-46
TRANSISTOR
DTC114YKA-T146
ICF-CDK70
MAIN
Ref. No.
Part No.
Description
Remark
< RESISTOR >
Ref. No.
Part No.
Description
R363
R364
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
10K
10K
5%
5%
1/10W
1/10W
Remark
R101
R103
R104
R105
R107
1-216-833-11
1-216-821-11
1-216-825-11
1-216-821-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
2.2K
1K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R365
R366
R367
R368
R415
1-216-817-11
1-216-817-11
1-216-817-11
1-216-817-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
470
470
470
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R108
R109
R110
R111
R112
1-216-853-11
1-216-825-11
1-216-841-11
1-216-845-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470K
2.2K
47K
100K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R416
R440
R441
R442
R443
1-216-817-11
1-216-821-11
1-216-829-11
1-216-821-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
1K
4.7K
1K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R114
R116
R117
R201
R203
1-216-853-11
1-216-833-11
1-216-837-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470K
10K
22K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R444
R445
R460
R461
R462
1-216-821-11
1-216-829-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
4.7K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R204
R205
R207
R208
R209
1-216-825-11
1-216-821-11
1-216-841-11
1-216-853-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
1K
47K
470K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R463
R464
R465
R466
R467
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R210
R211
R212
R214
R216
1-216-841-11
1-216-845-11
1-216-837-11
1-216-853-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
100K
22K
470K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R468
R469
R470
R471
R472
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R217
R301
R302
R303
R304
1-216-837-11
1-216-809-11
1-216-809-11
1-216-817-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
100
100
470
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R473
R474
R475
R476
R477
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R334
R335
R336
R337
R338
1-216-841-11
1-216-841-11
1-216-841-11
1-216-841-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
47K
47K
47K
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R478
R479
R480
R801
R802
1-216-833-11
1-216-833-11
1-216-833-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R339
R340
R341
R342
R343
1-216-817-11
1-216-817-11
1-216-817-11
1-216-841-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
470
470
47K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R803
R804
R805
R806
R807
1-216-821-11
1-216-821-11
1-216-864-11
1-216-864-11
1-216-821-11
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
1K
1K
0
0
1K
5%
5%
1/10W
1/10W
5%
1/10W
R344
R345
R346
R347
R348
1-216-841-11
1-216-841-11
1-216-837-11
1-216-837-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
47K
22K
22K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R808
R809
R810
R811
R812
1-216-864-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
1K
1K
1K
1K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R349
R350
R351
R352
R353
1-216-837-11
1-216-837-11
1-216-837-11
1-216-837-11
1-216-789-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
22K
22K
22K
2.2
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R814
R815
R816
R817
R819
1-216-821-11
1-216-817-11
1-216-817-11
1-216-821-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
470
470
1K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R354
R355
R357
R358
R359
1-216-789-11
1-216-789-11
1-216-864-11
1-216-825-11
1-216-825-11
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
2.2
2.2
0
2.2K
2.2K
5%
5%
1/10W
1/10W
5%
5%
1/10W
1/10W
R820
R821
R822
R823
R824
1-216-841-11
1-216-841-11
1-216-841-11
1-216-841-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
47K
47K
47K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R360
R361
R362
1-216-821-11
1-216-809-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
1K
100
22K
5%
5%
5%
1/10W
1/10W
1/10W
R825
R826
R827
1-216-841-11
1-216-817-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
47K
470
470
5%
5%
5%
1/10W
1/10W
1/10W
45
ICF-CDK70
Ver. 1.1
MAIN MEGA BASS
Ref. No.
POWER
Part No.
Description
R828
R829
1-216-864-11
1-216-833-11
SHORT CHIP
METAL CHIP
0
10K
R830
R831
R832
R833
R834
1-216-833-11
1-216-864-11
1-216-833-11
1-216-833-11
1-216-864-11
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
R835
R836
R839
R840
R842
1-216-833-11
1-216-833-11
1-216-821-11
1-216-833-11
1-216-833-11
R844
R846
R847
R848
R849
REMOTE CONTROL
Remark
5%
1/10W
10K
0
10K
10K
0
5%
1/10W
5%
5%
1/10W
1/10W
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
1K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1-216-833-11
1-216-821-11
1-216-849-11
1-216-821-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
220K
1K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R850
R851
R852
R853
R854
1-216-821-11
1-216-833-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
1K
10K
0
0
0
5%
5%
1/10W
1/10W
R855
R856
R857
R858
R859
1-216-821-11
1-216-821-11
1-216-841-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
47K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R860
R863
R864
R865
R866
1-216-821-11
1-216-821-11
1-216-833-11
1-216-821-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
10K
1K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R867
R870
R872
R874
R875
1-216-821-11
1-216-821-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R876
R878
R879
R880
R881
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R882
R883
R884
R885
R886
1-216-864-11
1-216-821-11
1-216-821-11
1-216-817-11
1-216-817-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
1K
1K
470
470
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R887
R888
R895
R897
R963
1-216-821-11
1-216-821-11
1-216-837-11
1-216-837-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
22K
22K
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R964
R965
R966
R969
1-216-821-11
1-216-805-11
1-216-833-11
1-216-797-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
47
10K
10
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
Ref. No.
Part No.
Description
Remark
X802
1-813-175-21 VIBRATOR, CERAMIC (4.19MHz)
************************************************************
A-1224-514-A
MEGA BASS BOARD, COMPLETE
**************************
< SWITCH >
S401
1-786-050-21 SWITCH, KEY BOARD (AUDIO IN)
S417
1-771-905-21 SWITCH, SLIDE (MEGA BASS)
************************************************************
A-1224-482-A
A-1225-192-A
POWER BOARD, COMPLETE (US)
POWER BOARD, COMPLETE (CND)
***********************
< CAPACITOR >
C901
C902
C903
C904
C907
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
100PF
10%
10%
10%
10%
5%
25V
25V
25V
25V
50V
C908
C909
1-126-947-11
1-162-970-11
ELECT
47uF
CERAMIC CHIP 0.01uF
20%
10%
35V
25V
< CONNECTOR >
CN902
CN904
1-815-443-11
1-815-443-21
PIN, CONNECTOR (PWB) 2P
PIN, CONNECTOR (PWB) 2P
< DIODE >
D901
D902
D903
D904
6-501-582-01
6-501-582-01
6-501-582-01
6-501-582-01
DIODE
DIODE
DIODE
DIODE
1N4002-B5
1N4002-B5
1N4002-B5
1N4002-B5
< FUSE HOLDER >
FH901
FH902
1-533-233-31
1-533-233-31
FUSE HOLDER (CND)
FUSE HOLDER (CND)
< COIL >
L901
1-402-964-11 COIL, AIR-CORE
L902
1-402-964-11 COIL, AIR-CORE
************************************************************
A-1224-499-A
< VIBRATOR >
X801
46
1-760-252-12
VIBRATOR, CRYSTAL (32.768kHz)
REMOTE CONTROL BOARD, COMPLETE
********************************
< CAPACITOR >
C408
1-107-826-11
CERAMIC CHIP 0.1uF
10%
16V
< LED >
D406
8-719-059-97
LED L-34HD (TIMER)
< IC >
IC401
6-600-349-21
IC NJL23H400A
< RESISTOR >
R428
1-216-821-11 METAL CHIP
1K
5%
1/10W
************************************************************
ICF-CDK70
TIMER
Ref. No.
Remark
Part No.
Description
Part No.
Description
A-1224-501-A
TIMER BOARD, COMPLETE
**********************
C51
C52
1-162-919-11
1-162-915-11
CERAMIC CHIP 22PF
CERAMIC CHIP 10PF
5%
0.5PF
50V
50V
1-833-902-21
2-893-520-01
3-254-081-01
CABLE, FLEXIBLE FLAT (4 CORE)
HOLDER (ALARM)
SCREW
C53
C54
C55
C56
C57
1-136-169-00
1-126-934-11
1-162-927-11
1-162-964-11
1-162-964-11
FILM
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22uF
220uF
100PF
0.001uF
0.001uF
5%
20%
5%
10%
10%
50V
16V
50V
50V
50V
C59
C60
C61
C62
C63
1-162-927-11
1-162-964-11
1-162-927-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
0.001uF
100PF
100PF
100PF
5%
10%
5%
5%
5%
50V
50V
50V
50V
50V
C65
C66
C68
C80
C95
1-126-963-11
1-162-927-11
1-162-927-11
1-162-970-11
1-162-964-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
4.7uF
100PF
100PF
0.01uF
0.001uF
20%
5%
5%
10%
10%
50V
50V
50V
25V
50V
< CAPACITOR >
C406
C407
1-162-927-11
1-162-927-11
CERAMIC CHIP 100PF
CERAMIC CHIP 100PF
5%
5%
50V
50V
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< RESISTOR >
R419
R420
R421
R426
R427
1-216-825-11
1-216-821-11
1-216-825-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
1K
2.2K
1K
1K
Ref. No.
TU
Remark
< SWITCH >
< FILTER >
S413
S414
S415
1-786-050-21
1-786-050-21
1-478-061-21
SWITCH, KEY BOARD (CLOCK/D.S.T.)
SWITCH, KEY BOARD (MODE)
ENCODER, ROTARY
(TIMER, PUSH START/STOP)
************************************************************
A-1109-056-A
TU BOARD, COMPLETE
*******************
CF2
CF4
1-760-235-81
1-781-962-21
FILTER, CERAMIC
FILTER, CERAMIC
< CONNECTOR >
CNP1
1-568-854-11
CONNECTOR, FFC 11P
< TRIMMER >
< CAPACITOR >
C1
C4
C7
C8
C9
1-162-923-11
1-162-964-11
1-162-910-11
1-162-964-11
1-162-915-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47PF
0.001uF
5PF
0.001uF
10PF
5%
10%
0.25PF
10%
0.5PF
50V
50V
50V
50V
50V
C10
C11
C12
C13
C14
1-126-960-11
1-107-826-11
1-126-963-11
1-162-970-11
1-164-227-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
1uF
0.1uF
4.7uF
0.01uF
0.022uF
20%
10%
20%
10%
10%
50V
16V
50V
25V
25V
C15
C18
C20
C21
C22
1-164-227-11
1-126-934-11
1-107-826-11
1-126-960-11
1-107-826-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.022uF
220uF
0.1uF
1uF
0.1uF
10%
20%
10%
20%
10%
25V
16V
16V
50V
16V
C23
C24
C26
C27
C29
1-126-960-11
1-162-960-11
1-162-927-11
1-162-927-11
1-104-665-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
1uF
220PF
100PF
100PF
100uF
20%
10%
5%
5%
20%
50V
50V
50V
50V
25V
C30
C31
C32
C33
C34
1-162-970-11
1-162-919-11
1-162-964-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
22PF
0.001uF
0.01uF
0.01uF
10%
5%
10%
10%
10%
25V
50V
50V
25V
25V
C35
C37
C39
C41
C42
1-162-970-11
1-162-970-11
1-107-826-11
1-164-230-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.1uF
220PF
100PF
10%
10%
10%
5%
5%
25V
25V
16V
50V
50V
C43
C47
C49
1-162-919-11
1-162-915-11
1-161-051-00
CERAMIC CHIP 22PF
CERAMIC CHIP 10PF
CERAMIC
0.01uF
5%
0.5PF
10%
50V
50V
25V
CT1
CT3
1-141-442-91
1-141-304-21
CAP, CERAMIC TRIMMER
CAP, CERAMIC TRIMMER
< DIODE >
D1
D2
D3
D10
D11
8-719-078-48
8-719-078-48
8-719-050-69
8-719-988-61
8-719-988-61
DIODE
DIODE
DIODE
DIODE
DIODE
KV1471ETR-G
KV1471ETR-G
KV1520N
1SS355TE-17
1SS355TE-17
< IC >
IC1
IC2
6-700-512-01
8-759-483-40
IC TA2149BN
IC LC72137M-TLM-E
< JUMPER RESISTOR >
JC1
JC2
JC3
JC4
JC5
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC6
JC11
JC12
JC13
JC33
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC34
1-216-864-11
SHORT CHIP
0
< COIL >
L1
L2
L3
L4
L11
1-409-775-11
1-416-509-11
1-754-117-12
1-411-234-21
1-414-142-11
COIL, AIR-CORE
COIL, AIR-CORE
ANTENNA, FERRITE-ROD (MW)
COIL, AM OSC
INDUCTOR
1uH
47
ICF-CDK70
Ver. 1.1
TU VOL
Ref. No.
L21
Part No.
Description
1-410-509-11
INDUCTOR
Remark
Ref. No.
Part No.
10uH
Description
Remark
MISCELLANEOUS
**************
< RESISTOR >
R1
R2
R3
R4
R5
1-216-817-11
1-216-817-11
1-216-833-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
470
10K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R10
R11
R13
R14
R24
1-216-805-11
1-216-825-11
1-216-821-11
1-216-821-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47
2.2K
1K
1K
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R30
R31
R32
R33
R40
1-216-837-11
1-216-829-11
1-216-845-11
1-216-833-11
1-216-849-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
4.7K
100K
10K
220K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R41
R50
R51
R52
R53
1-216-833-11
1-216-821-11
1-216-833-11
1-216-864-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
10K
1K
10K
0
4.7K
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
R54
R55
R56
R57
R58
1-216-817-11
1-216-833-11
1-216-813-11
1-216-809-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
10K
220
100
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R59
R60
R61
R63
R65
1-216-825-11
1-216-825-11
1-216-825-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
2.2K
2.2K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R91
R92
R94
1-216-813-11
1-216-813-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
220
220
1K
5%
5%
5%
1/10W
1/10W
1/10W
< TRANSFORMER/COIL >
T1
T2
1-433-741-11
1-419-465-11
TRANSFORMER, IF
COIL (DET)
< VIBRATOR >
X1
1-795-449-11 VIBRATOR, CRYSTAL (75kHz)
************************************************************
A-1224-506-A
VOL BOARD, COMPLETE
*******************
< CONNECTOR >
CN417
1-815-554-11
PIN, CONNECTOR (PWB) 6P
< RESISTOR >
R424
R425
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
1K
1K
5%
5%
1/10W
1/10W
< ROTARY ENCODER >
S416
1-480-074-11 ENCODER, ROTARY (VOLUME)
************************************************************
48
62
63
70
0 114
205
1-833-883-21
1-833-882-21
1-831-772-21
1-828-104-31
1-797-193-12
CABLE, FLEXIBLE FLAT (14 CORE)
CABLE, FLEXIBLE FLAT (12 CORE)
CABLE, FLEXIBLE FLAT (9 CORE)
CORD, POWER
MECHANICAL, CD (DLM3A23-11)
206
0 207
210
211
0 F901
1-832-025-21
8-820-070-07
1-833-881-21
1-832-836-21
1-533-451-12
CABLE, FLEXIBLE FLAT (16 CORE)
OPTICAL PICK-UP BLOCK (KSM-213CCP/C2NP)
CABLE, FLEXIBLE FLAT (14 CORE)
CABLE, FLEXIBLE FLAT (13 CORE)
FUSE, GLASS TUBE (DIA. 5) (3.15A/125V) (CND)
SP101
1-826-605-11 SPEAKER (6.6 cm) (L-CH)
SP201
1-826-605-11 SPEAKER (6.6 cm) (R-CH)
0 T901
1-435-917-22 TRANSFORMER, POWER
************************************************************
ACCESORRIES
************
1-833-879-21
2-893-494-01
2-898-235-11
2-898-235-21
3-009-707-01
3-011-879-01
3-097-586-01
3-267-151-11
3-897-241-01
A-1246-973-A
CORD, CONNECTION (WITH PLUG) (Audio cable)
CARDBOARD (Template)
MANUAL, INSTRUCTION (ENGLISH, FRENCH)
(CND)
MANUAL, INSTRUCTION (ENGLISH) (US)
SPACER
SCREW (M5X80), +B (Mounting screws)
HOLDER (DMP) (Digital music player holder)
LID BATTERY (for RMT-CCDK70A)
CLAMP, CORD
REMOTE COMMANDER
(RMT-CCDK70A//C (SET)) (including lid battery)
ICF-CDK70
MEMO
49
ICF-CDK70
REVISION HISTORY
Checking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page
Ver.
Date
Description of Revision
1.0
2007.01
NEW
1.1
2007.02
Addition of Part No. for COMPLETE REMOTE CONTROL BOARD
Change of Part No. for LID BATTERY (for RMT-CCDK70A)
(ECN-ECC07216/SPM-07013)