PDF Catalog

Transcription

PDF Catalog
A-PDF MERGER DEMO
Order Information
Precision Tank & Equipment Co. stocks a complete line of fertilizer related accessories, replacement and repair parts. This
PT&E Parts Catalog contains listings for over 7,500 different parts held in our inventory, ready for immediate shipment. We
carry all parts for Precision’s line of applicators, tanks, mixers, and 10-34-0 production units. Precision also carries parts
for almost every other applicator make and model.
Toll Free “Parts Hotline” • 1-800-811-7814
Precision makes it easy to order. Just call our Toll Free "Parts Hotline" and place your order. If your order is placed before
3:00 p.m. Central Time, we guarantee same-day shipment of items in stock. Daily shipments can be made from either of
our two locations via Mail – UPS – Truck or Air. Overnight services are available, if needed.
Service or Repair
Precision employs a staff of professionals that have the experience to service and repair our complete line of equipment.
So when you need service or repair, put the Precision professionals to work for you. Call us Toll Free at 1-800-811-7814 to
discuss your service or repair needs.
Terms and Conditions
Net 30 days to firms with approved credit. All shipments F.O.B., Athens or Virginia, Illinois. Invoices dated the day of
shipment, and at prices in effect at time of shipment. Accounts not paid according to terms, a finance charge of 2% per
month (which is an annual percentage rate of 24%) will be applied to that portion of your previous balance which is 30
days or more outstanding. All prices are subject to any Federal, State or local taxes required by law.
We ask the customer to check all merchandise upon receipt and report shortages, damages, etc. within 10 days.
Merchandise cannot be returned without prior approval. Original packing slip and invoice must accompany goods returned
before credit will be issued. Special order items cannot be returned. Precision reserves the right to charge a 15%
restocking charge on items returned for credit.
Warranty
No one shall warranty, either implied or expressed, as to the performance, efficiency or other capability that has not been
stated in the manufacturer’s guarantee.
The manufacturer’s policy will determine any replacement of defective merchandise or parts. Such merchandise returned
for inspection must be prepaid.
Under no circumstances shall we be responsible for any damage, loss, or expense as a result of defective materials or
workmanship, installation, use or other causes beyond the replacement of defective parts.
HOME OFFICE
P.O. BOX 20 • VIRGINIA, IL 62691-0020
(217) 452-7228 • Fax: (217) 452-3956
(800) 258-4197
ATHENS LOCATION
R.R. 2, BOX 42 • ATHENS, IL 62613
(217) 636-7023 • Fax: (217) 636-8790
(800) 811-7814
www.precisiontank.com
© 2002 Precision Tank & Equipment Company All rights reserved.
Table of Contents
PUMPS
Defco Pumps – Multi-State Centrifugal ........................................................................................................1
Defco Pumps – Single-Stage Centrifugal .....................................................................................................2
Banjo Pumps ................................................................................................................................................7
Corken Pumps ..............................................................................................................................................9
Scot Pumps ................................................................................................................................................10
MP Pumps...................................................................................................................................................11
Ace Pumps .................................................................................................................................................14
Shur Flo Pumps ..........................................................................................................................................14
Hypro Pumps ..............................................................................................................................................14
TEEJET PRODUCTS
TeeJet Selection Guide for Broadcast Spraying.........................................................................................15
Floodjet – Wide Angle Flat Spray Tips and Nozzles ..................................................................................17
Quick Turbo Floodjet – Wide Angle Flat Spray Tips...................................................................................18
Fulljet – Wide Angle Full Cone Spray Tips .................................................................................................18
Turbo Floodjet – Wide Angle Flat Spray Tips .............................................................................................19
Floodjet – Wide Angle Flat Spray Tips and Nozzles ..................................................................................19
Turbo TeeJet – Wide Angle Flat Spray Tips ...............................................................................................20
AI TeeJet – Air Induction Spray Tips...........................................................................................................20
XR TeeJet – Extended Range Flat Spray Tips ...........................................................................................21
DG TeeJet – Drift Guard Spray Tips...........................................................................................................21
TeeJet – VisiFlo Flat Spray Tips .................................................................................................................22
Twinjet – Twin Flat Spray Tips ....................................................................................................................22
TeeJet – Double Outlet Flat Spray Tips......................................................................................................23
TeeJet – Off-Center Flat Spray Tips – Smaller Capacities.........................................................................23
TeeJet – Swivel Spray Nozzles with Off-Center Flat Spray Tips – Larger Capacities ...............................23
TeeJet – Area Measurement.......................................................................................................................24
TeeJet – Formulas and Conversion Factors...............................................................................................25
Technical Information..................................................................................................................................26
TeeJet – Droplet Size Information ..............................................................................................................27
TeeJet Selection Guide for Banding and Directed Spraying ......................................................................29
Quick TeeJet Caps......................................................................................................................................31
TeeJet – Even Flat Spray Tips....................................................................................................................33
Conejet – VisiFlo Hollow Cone Spray Tips.................................................................................................33
Streamjet – Solid Stream Spray Nozzles ...................................................................................................34
TeeJet – Flow Regulators ...........................................................................................................................34
TeeJet Orifice Discs – Disc-Core Type Cone Spray Tips ...........................................................................34
TeeJet – Hose Drops ..................................................................................................................................35
TeeJet – Tip Strainers.................................................................................................................................35
TeeJet – Container Rinsing Nozzles...........................................................................................................35
TeeJet – Swivel Nozzle Bodies...................................................................................................................36
TeeJet – ChemSaver Diaphragm Check Valves.........................................................................................36
TeeJet – ChemSaver Air Shutoff Valve.......................................................................................................36
Quick TeeJet – Multiple Nozzle Bodies & Assemblies for Dry Booms .......................................................37
Quick TeeJet – Multiple Nozzle Bodies & Assemblies for Wet Booms ......................................................39
DirectoValve – AA440 Manifold ..................................................................................................................41
DirectoValve – 2-Way Electric Control Ball Valves .....................................................................................41
DirectoValve – 2-Way Electrically Operated Solenoid Valves ....................................................................42
DirectoValve – Manual Pressure Relief/Regulating Valves ........................................................................43
TeeJet – Flanged Fittings ...........................................................................................................................43
GunJet – Regular & Low Pressure Spray Guns.........................................................................................44
TeeJet – Calibration/Adjustment Accessories.............................................................................................44
All information on Teejet products contained in this catalog is copyrighted, 2000 © Spraying Systems Company.
VALVES
Anhydrous Ammonia Valves .......................................................................................................................45
Ball Valves & Repair Kits ............................................................................................................................48
12V Solenoid & Motorized Ball Valves .......................................................................................................55
Butterfly Valves ...........................................................................................................................................57
Check Valves ..............................................................................................................................................59
Miscellaneous Valves..................................................................................................................................59
NH3 PRODUCTS
NH3 Knives.................................................................................................................................................60
Continental NH3 Meters .............................................................................................................................61
STRAINERS ...........................................................................................................................................64
GAUGES & INSTRUMENTATION ...................................................................................................69
HOSE PRODUCTS
Hose............................................................................................................................................................72
Hose Barb/King Nipple ...............................................................................................................................74
COUPLERS AND CLAMPS
Quick Couplers ...........................................................................................................................................79
Acme Fittings ..............................................................................................................................................83
NH3 Hose Barb Coupling ...........................................................................................................................84
Clamps........................................................................................................................................................85
PIPE AND FITTINGS
Metal and PVC Pipe & Fittings ...................................................................................................................88
Stainless Steel Flex Connectors.................................................................................................................96
Nylon Pipe Fittings......................................................................................................................................97
Polypropylene Pipe Fittings ........................................................................................................................98
Pipe and Fitting Supplies..........................................................................................................................102
MISCELLANEOUS PRODUCTS
Cylinders ...................................................................................................................................................103
Miscellaneous Nozzles & Accessories .....................................................................................................103
Hydraulic Pumps & Cylinders ...................................................................................................................104
Tank Accessories ......................................................................................................................................104
Lawn Care Equipment ..............................................................................................................................106
TeeJet Guideline Guidance System .........................................................................................................107
Raven Swath Smart..................................................................................................................................107
Spray Controllers/Monitors .......................................................................................................................108
Foam Markers ...........................................................................................................................................110
Boom Parts ...............................................................................................................................................110
Tires and Wheels ......................................................................................................................................111
Bearings & Drive Systems ........................................................................................................................112
Sprockets & Pulleys ..................................................................................................................................114
Coupling, Motor/Pump ..............................................................................................................................116
Electric Motors ..........................................................................................................................................117
Miscellaneous Parts & Products ...............................................................................................................118
Safety Equipment & Decals ......................................................................................................................119
New Leader ..............................................................................................................................................124
DEFCO PUMPS – Multi-Stage Centrifugal
DEFCO 520 Series Pumps
DEFCO D-520 Pump Parts
A578
A926 A927 A926
A982
A536
A554
A981
A532
A533
A563
A537
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
DEFCO PUMPS – Single-Stage Centrifugal
DEFCO 2500 Series Pumps
DEFCO A-2500 Pump Parts
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
DEFCO PUMPS – Single-Stage Centrifugal
DEFCO 7600 Series Pumps
DEFCO 7600 Pump Parts
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
DEFCO PUMPS – Single-Stage Centrifugal
DEFCO B-7600-DHD Pump Parts
14
13
22
12
10
8
11
9
7
5
3
26
6
15
2
25
27
21
4
1
24
16
17
23
18
28
20
19
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
DEFCO PUMPS – Single-Stage Centrifugal
DEFCO A-4500 TK Pump
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
DEFCO PUMPS – Single-Stage Centrifugal
DEFCO A-8200 Pump
DEFCO A-8200 Pump Parts
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
BANJO PUMPS
BANJO Poly Centrifugal Pumps
BANJO Poly Centrifugal 11⁄2" & 2" Pump Parts
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
BANJO PUMPS
BANJO Cast Iron Centrifugal Pumps
BANJO Cast Iron Centrifugal 1-1/2" & 2" Pump Parts
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
BANJO & CORKEN PUMPS
BANJO 222 Series & Wet Seal Pumps
CORKEN Pumps & Parts
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
SCOT PUMPS
PSP 303 Pump
* Other pumps are available w/electric clutch drive or hydraulic motor driven
PSP 303 Pump Parts
*Pressure Seal Tank Assembly (Mfg. # 118.000.236)
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
MP PUMPS
Flo 5 & 8 Pump Parts
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
MP PUMPS
Flo 10 & 15 Pump Parts
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
MP PUMPS
MP300 Pump
* Other pumps this style are available
MP300 Pump Parts
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
ACE, SHUR FLO & HYPRO PUMPS
ACE Pump Parts
SHUR FLO Pumps & Parts
HYPRO Pumps
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
TEEJET SELECTION GUIDE FOR BROADCAST SPRAYING
Available Materials
Pre-Emerge
Excellent
Excellent
Contact
Systemic
Excellent
Good
Excellent
Excellent
Good
Excellent
Contact
Systemic
Good
Excellent
(At Medium Pressure)
WIDE ANGLE FLAT SPRAY TIP
Contact
Systemic
Good
Excellent
(At Medium Pressure)
Excellent
Excellent
AIR INDUCTON SPRAY TIP
Excellent
EXTENDED RANGE FLAT SPRAY TIP
(At Lower Pressure)
(At Lower Pressure)
Excellent
Excellent
Excellent
Excellent
Excellent
Excellent
Good
Excellent
Good
Good
Good
Good
(At Lower Pressure)
Good
110°
only
Good
Excellent
Excellent
110°
only
Good
Good
Good
Good
Excellent
Good
Excellent
Good
Excellent
Excellent
DRIFT GUARD FLAT SPRAY TIP
(At Lower Pressure)
Air Induction
Spray Tip
Large, air-filled drops
Larger droplets for less drift
Uniform coverage in broadcast spraying
Nozzle spacing – 20 inches (50 cm)
Spraying pressure – 30-100 PSI
(3-8 bar)
STANDARD FLAT SPRAY TIP
Excellent
Large droplets to reduce drift
Removable pre-orifice
Nozzle spacing – 20 inches
(50 cm)
Spraying pressure –
30-60 PSI (2-4 bar)
110°
only
Excellent
(At Lower Pressure)
(At Medium Pressure)
Excellent
Excellent
(At Lower Pressure)
(At Lower Pressure)
Excellent
(At Lower Pressure)
Ceramic
Soil
Incorporated
Drift Guard
Flat Spray Tip
Hardened
Stainless
Steel
Liquid
Fertilizer
Post-Emerge
Stainless
Steel
Insecticides
Polymer
Fungicides
Brass
Herbicides
TWIN FLAT SPRAY TIP
Excellent
Excellent
Excellent
Excellent
Excellent
Excellent
Twin Flat
Spray Tip
WIDE ANGLE FLAT SPRAY TIP
Excellent
Excellent
Excellent
Excellent
Excellent
Excellent
Excellent
Penetrates crop residue
or dense foliage
Smaller droplets for
thorough spray coverage
Nozzle spacing –
20 inches (50 cm)
Spraying pressure –
30-60 PSI (2-4 bar)
WIDE ANGLE FULL CONE TIP
EIGHT ORIFICE
*Note: Consult the chemical manufacturer’s product label for specific rate and application recommendations.
Characteristics of Common Spray Tip Materials
Extended Range
Flat Spray Tip
Ceramic
Superior wear life; highly resistant to abrasive
and corrosive chemicals
Hardened Stainless Steel
Very good wear life; good durability and
chemical resistance
Uniform coverage along boom
Smaller droplets at high pressures for
thorough coverage
Pre-orifice design produces large
droplets to reduce drift
Nozzle spacing – 20 inches (50 cm)
Nozzle spacing – 20-40 inches
(50-100 cm)
AT LOW
PRESSURE
AT HIGH
PRESSURE
Precision Tank & Equipment Co.
Larger droplets – less drift
Nozzle spacing –
40 inches (100 cm)
Spraying pressure –
15-40 PSI (1-3 bar)
Wide Angle
Flat Spray Tip
Good spray penetration
Eight
Orifice
Large, round free passages to
minimize clogging
Uniform coverage along boom
Nozzle spacing – 20 inches (50 cm)
Uniformly distributed streams
of liquid fertilizers
Excellent to use with automatic
sprayer controls
Spraying pressure – 30-60 PSI
(2-4 bar)
Brass
Poor wear life; susceptible to corrosion,
especially with fertilizers
Uniform coverage along boom
Spraying pressure –
10-40 PSI (0.7-3 bar)
Standard
Flat Spray Tip
Polymer
Good wear life; good chemical resistance;
orifice susceptible to damage when cleaned
improperly
Wide Angle
Full Cone Tip
Uniform coverage at lower pressures
Spraying pressure –
15-60 PSI (1-4 bar)
Stainless Steel
Good wear life; excellent chemical resistance;
durable orifice
Wide Angle
Flat Spray Tip
Coarse droplets reduce drift
Excellent spray pattern quality
Semicircle spray pattern
Unequalled drift control from
15-90 PSI (1-6 bar)
Spraying pressure –
15-40 PSI (1-3 bar)
Relative droplet size for each spray tip is shown in each pattern.
15
Parts Hotline: 1-800-811-7814
Precision Tank & Equipment Co.
16
Parts Hotline: 1-800-811-7814
FLOODJET – Wide Angle Flat Spray Tips and Nozzles
The FloodJet tips and nozzles produce a very wide deflector
type flat spray pattern. Round orifice minimizes clogging.
How to order – Specify tip number.
Examples:
1/8K-SS5 – Stainless Steel
QCK-SS100 – Stainless Steel with VisiFlo color-coding
Standard
FloodJet Nozzles
(1/8 thru 1 NPT)
QCK Quick FloodJet
Spray Tip
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
QUICK TURBO FLOODJET – Wide Angle Flat Spray Tips
The revolutionary Quick Turbo FloodJet
nozzle combines the precision and uniformity
of a flat spray nozzle with the clog-resistance
and wide angle pattern of flooding nozzles. It
uses an exclusive new design to increase
droplet size and distribution uniformity.
Features:
Grooved side molding for automatic align-
ment with any quick-connect coupler
Stainless steel with color-coding for
easy size identification
Available in standard sizes from
1.5 GPM up to 24.0 GPM at
pressures of 10-40 PSI
Patented turbulence chamber creates
a dramatic improvement in pattern
uniformity
Pre-orifice design produces larger droplets
for reduced drift
Large round orifice reduces clogging
How to order:
Specify tip number.
Example:
QCTF-VS40 – Stainless Steel with VisiFlo®
color-coding
FULLJET – Wide Angle Full Cone Spray Tips
Wide spray angle allows use on
Typical Applications:
Features:
See selection guide on pages 44 and
45 for recommended typical application
for FullJet.
Large droplets to reduce drift
Excellent spray distribution over a
range of pressures (15-40 PSI/1-3 bar)
Ideal for use on rigs with sprayer
controllers
Precision Tank & Equipment Co.
409 spacings
Available in VisiFloT color-coding system in
all stainless steel or CelconT with stainless
steel vane
Can be used with No. CP25607-*-NY
for Quick TeeJetT connection. Reference
page 104 for more information
1
Parts Hotline: 1-800-811-7814
TURBO FLOODJET – Wide Angle Flat Spray Tips
Typical Applications:
See selection guide for recommended
typical application for Turbo FloodJet.
QTC Cam-Loc Adapter
Provides easy changeover from high
capacity to lower capacity nozzles
Features:
Excellent spray distribution for uniform
coverage along the boom
Nozzle design incorporates a pre-orifice to
produce larger droplets for less drift
Large round orifice reduces clogging
Stainless steel with VisiFlo® color-coding
band for easy size identification
Can be used with No. CP25599-* -NY
Adapter fits standard 3⁄4” quick
connect Cam-Loc holders
Corrosion-resistant stainless steel
and polypropylene construction
Rated up to 100 PSI (7 bar)
CP1325 Cap
TFVS Turbo
FloodJet®
Spray Tip
Quick TeeJet® cap for automatic alignment.
QCT
Cam-Loc
Adapter
FLOODJET – Wide Angle Flat Spray Tips and Nozzles
The FloodJet tips and nozzles produce a very wide deflector
type flat spray pattern. Round orifice minimizes clogging.
How to order:
Specify tip number.
Examples:
1/4K-5
– Brass
TK-VS5
– Stainless Steel with VisiFloT color-coding
TK-SS5
– Stainless Steel
TK-VS FloodJet
Spray Tip
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
TURBO TEEJET – Wide Angle Flat Spray Tips
Typical Applications:
See selection guide on pages 46 and 47 for
recommended typical application for Turbo
TeeJet.
Superior wear characteristics
Larger droplets for less drift — 15-90 PSI
(1-6 bar)
Automatic spray alignment with
25612-*-NYR Quick TeeJet cap and gasket.
Reference page 104 for more information
Features:
Tapered edge wide angle flat spray pattern
Now available in 06 and 08 capacities
for uniform coverage in broadcast spraying
Large, rounded internal passage to
minimize clogging
Excellent resistance to corrosive solutions
AI TEEJET – Air Induction Spray Tips
Typical Applications:
Larger droplets for less drift
See selection guide on pages 46 and 47 for
recommended typical application for AI
TeeJet.
Depending on the chemical, produces large
Features:
Stainless steel insert produces tapered
edge flat spray pattern for uniform
coverage in broadcast spraying
Polymer insert holder and pre-orifice
air-filled drops through the use of
a venturi air aspirator
Automatic spray alignment with
25598-*-NYR Quick TeeJetT cap
and gasket. Reference page 104 for
more information
Now available in 06, 08, and
10 capacities
with VisiFlo® color-coding
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
XR TEEJET – Extended Range Flat Spray Tips
Typical Applications:
Ideal for rigs equipped with sprayer
See selection guide on pages 46 and 47 for
recommended typical application for
XR TeeJet.
Reduces drift at lower pressures, better
controllers
coverage at higher pressures
Available in stainless steel, hardened
Features:
Excellent spray distribution over a wide
range of pressures—15-60 PSI (1-4 bar)
stainless steel, ceramic and polymer in
80° and 110° spray angles…with
VisiFlo® color-coding
Available in ceramic sizes 03 thru 08
Automatic spray alignment with
25612-*-NYR Quick TeeJet cap and gasket.
Reference page 104 for more information
Automatic spray alignment for sizes 10 and
15 with 25610-*-NYR Quick TeeJet cap
and gasket. Reference page 104 for more
information
DG TEEJET – Drift Guard Spray Tips
Typical Applications:
See selection guide on pages 46 and 47 for
recommended typical application for
DG TeeJet.
Features:
Pre-orifice design produces larger droplets
and reduces the small drift prone droplets,
minimizing off-target spray contamination
Precision Tank & Equipment Co.
Tapered edge flat spray pattern provides
uniform coverage when adjacent nozzle
patterns are overlapped in broadcast
spraying
Automatic spray alignment with
25612-*-NYR Quick TeeJetT cap and
gasket. Reference page 104 for more
information
The color-coded pre-orifice is removable
for any necessary cleaning operations
Available in both 80° and 110° spray
angles with durable stainless steel
orifice
1
Parts Hotline: 1-800-811-7814
TEEJET – VisiFlo Flat Spray Tips
Typical Applications:
See selection guide for recommended typical
application for TeeJet.
Features:
Tapered edge flat spray pattern for uniform
coverage in broadcast spraying
VisiFlo color-coded version available in
stainless steel, hardened stainless steel,
ceramic and polymer in 80° or 110° spray
angles in selected sizes
Standard version (not color-coded)
available in 15°, 25°, 40°, 50° and 65°
spray angles in brass, stainless steel
or hardened stainless steel
See page 66 for TeeJet even flat
spray tips
Automatic spray alignment with
25612-*-NYR Quick TeeJet cap and gasket.
Automatic spray alignment for sizes
10 thru 20 with 25610-*-NYR Quick TeeJet
cap and gasket.
TWINJET – Twin Flat Spray Tips
Typical Applications:
See selection guide on pages 46 and 47 for
recommended typical application for TwinJet.
Features:
Penetrates crop residue or dense foliage
Smaller droplets for thorough coverage
Better spray distribution along boom
than with hollow cone nozzles
Available in brass or stainless steel
with VisiFloT color-coding in 65°,
80° and 110° spray angles
See page 69 on TwinJet even flat
spray tips
Automatic spray alignment with
25598-*-NYR Quick TeeJetT cap and
gasket.
Reference Technical Section, pages
for additional information on drift
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
TEEJET – Double Outlet Flat Spray Tips
150° Series
Stainless Steel
and Brass
Suggested for postdirected application
with hose drops.
How to order:
Example: TQ150-03-SS
Stainless Steel
TEEJET – Off-Center Flat Spray Tips – Smaller Capacities
TeeJet Off-Center spray
tips are commonly
installed in double and
single swivel nozzle
bodies. Because these
bodies are adjustable for
angular position, a wide spray
swath is easily obtained. See page 74 for
swivels and hose drops.
How to order:
Specify tip number and material.
Example: OC-02 Brass
TEEJET – Swivel Spray Nozzles with Off-Center Flat Spray Tips – Larger Capacities
Large capacity swivel nozzles, available in both single or double
styles, are available with 3⁄4” NPT (F) inlet connections for use
as boomless type nozzles. For double swivels the tabulated GPM
capacities are twice those shown for single swivels.
How to order:
Specify swivel number, material.
Example: 4629-3⁄4-TOC10 Brass
Type 4629-3⁄4-TOC Single
Swivel with 3⁄4” NPT (F) pipe
connection. Brass.
Precision Tank & Equipment Co.
Extra Wide Flat Spray Coverage
W = Maximum effective coverage with
nozzle mounted at 369 height.
1
Type 4418-3⁄4-2TOC Double
Swivel with 3⁄4” NPT (F) pipe
connection. Brass.
Parts Hotline: 1-800-811-7814
TEEJET – Area Measurement
It is essential to know the amount of area that you intend to cover
when applying a pesticide or fertilizer. Turf areas such as home lawns
and golf course greens, tees and fairways should be measured in
square feet or acres, depending upon the units needed.
Circular Areas
Rectangular Areas
Area
π_______________
x Diameter2 (d)
=
π =
4
3.14159
Example:
What is the area of a green that has a diameter of 45 feet?
Area = Length (l) x Width (w)
Area
Example:
What is the area of a lawn that is 300 feet long and 150 feet wide?
π x (45 feet)2
_______________
4
1,590 square feet
=
=
Area = 300 feet x 150 feet
= 45,000 square feet
Area in acres
=
=
By using the following equation, it is possible to determine the area in
acres.
Area in square feet
___________________
43,560 sq. ft. per acre
(There are 43,560 square feet in an acre.)
Area in acres
=
3.14 x 2,025
_______________
4
1,590 square feet
__________________
43,560 sq. ft. per acre
0.04 acres
=
Irregular Areas
Example:
Area in acres
45,000 sq. ft.
___________________
43,560 sq. ft. per acre
= 1.03 acres
=
Triangular Areas
Any irregularly shaped turf area can usually be reduced to one or more
geometric figures. The area of each figure is calculated and the areas are
then added to obtain the total area.
Example:
What is the total area of the Par-3 hole illustrated above?
Area
=
The area can be broken into a triangle (area 1), a rectangle
(area 2) and a circle (area 3). Then use the previously
mentioned equations for determining areas to find the total area.
Base (b) x Height (h)
__________________
2
Example:
The base of a corner lot is 250 feet while the height is 50 feet. What is
the area of the lot?
Area
=
=
250 feet x 50 feet
_______________
2
6,250 square feet
Area 1
=
25 feet x 30 feet
______________
2
= 375 square feet
Area 2
=
25 feet x 475 feet
= 11,875 square feet
Area 3
=
3.14 x (45 feet)2
______________
4
= 1,590 square feet
Total Area
Area in acres
=
=
6,250 square feet
__________________
43,560 sq. ft. per acre
0.14 acres
Precision Tank & Equipment Co.
= 375 + 11,875 + 1,590 = 13,840 square feet
=
1
13,840 square feet
__________________
43,560 sq. ft. per acre
= 0.32 acres
Parts Hotline: 1-800-811-7814
TEEJET – Formulas and Conversion Factors
Measuring Travel Speed
Useful Formulas
GPA x MPH x W
GPM
= ———————
5,940
(Per Nozzle)
GPM
(Per Nozzle)
GPA
—
—
Gallons Per
1000 Square
Feet
GAL/1000FT2 x MPH x W
= ———————————
136
MPH — Miles Per Hour
5,940 x GPM (Per Nozzle)
= ———————————
MPH x W
W — Nozzle spacing (in inches) for broadcast spraying
GAL/1000FT2
GPM
GAL/1000FT2
136 x GPM (Per Nozzle)
= ——————————
MPH x W
— Spray width (in inches) for
single nozzle, band spraying
or boomless spraying
Gallons Per Minute
— Row spacing (in inches) divided
by the number of nozzles per
row for directed spraying
GPA — Gallons Per Acre
Speed (MPH)
Spraying Solutions Other Than Water — New Method
Since all the tabulations in this catalog are
based on spraying water, which weighs 8.34
lbs. per USA gallon, conversion factors must be
used when spraying solutions which are heavier
or lighter than water. To determine the proper
size nozzle for the solution to be sprayed, first
multiply the desired GPM or GPA of solution by
the water rate conversion factor. Then use the
new converted GPM or GPA rate to select the
proper size nozzle.
GPA (solution) x Conversion factor
= GPA (from table)
20 GPA (28%) x 1.13
= 22.6 GPA (water)
The applicator should choose a nozzle size
that will supply 22.6 GPA of water at the
desired pressure.
Specific Gravity
7.0 lbs. per gallon.84
8.0 lbs. per gallon.96
8.34 lbs. per gallon — WATER
9.0 lbs. per gallon1.08
10.0 lbs. per gallon1.20
10.65 lbs. per gallon — 28% nitrogen
.92
.98
1.00
1.04
1.10
1.28
11.0 lbs. per gallon1.32
12.0 lbs. per gallon1.44
14.0 lbs. per gallon1.68
1.15
1.20
1.30
Distance (ft) x 60
= _________________
Time (seconds) x 88
Speeds
Example:
Desired application rate is 20 GPA of
28%N. Determine the correct nozzle size
as follows:
Weight of Solution
Measure a test course in the area to be
sprayed or in an area with similar surface
conditions. Minimum lengths of 100 and 200
feet are recommended for measuring speeds
up to 5 and 10 mph, respectively. Determine
the time required to travel the test course. To
help insure accuracy, conduct the speed
check with a partially loaded (about half full)
sprayer and select the engine throttle setting
and gear that will be used when spraying.
Repeat the above process and average the
times that were measured. Use the following
equation or the table below to determine
ground speed.
Conversion Factors
1.00
1.13
Speed in
MPH
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
Time Required in SECONDS
to Travel a Distance of:
100 Feet 200 Feet 300 Feet
136
68
45
34
27
23
19
17
15
14
—
—
—
—
—
—
—
—
273
136
91
68
55
45
39
34
30
27
25
23
21
19
18
17
16
15
409
205
136
102
82
68
58
51
45
41
37
34
31
29
27
26
24
23
Miscellaneous Conversion Factors
One Gallon = 128 Fluid Ounces
= 8 Pints
= 4 Quarts
= 3.79 Liters
= 0.83 Imperial Gallons
One Acre = 43,560 square feet
= 43.56 1000FT2 blocks
= 0.405 Hectares
One Hectare = 2.471 Acres
One Gallon Per Acre
= 2.9 Fluid Ounces per 1000FT2
= 9.35 Liters Per Hectare
One Gallon Per 1000FT2 = 43.56 Gallons
Per Acre
One Pound Per Square Inch
= 0.069 bar
= 6.896 Kilopascal
One Mile Per Hour
= 1.609 Kilometers
Per Hour
One Mile = 5,280 Feet
= 1,610 Meters
= 1.61 Kilometers
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
TECHNICAL INFORMATION
Nozzle Spacing
If the nozzle spacing on your boom is different
than those tabulated, multiply the tabulated GPA
coverages by one of the following factors.
To calculate a conversion factor for spacings
not listed in tables below, use the following
formula:
Conversion Factor =
Nozzle Spacing in table (inches)
——————————————
Your Nozzle Spacing (inches)
Other Spacing (inches)
Conversion Factor
Other Spacing (inches)
Conversion Factor
Other Spacing (inches)
Conversion Factor
2.5
2
1.67
1.43
1.25
1.11
.91
.83
.66
26
28
32
34
36
38
40
42
44
1.15
1.07
.94
.88
.83
.79
.75
.71
.68
28
30
32
34
36
38
42
44
48
1.43
1.33
1.25
1.18
1.11
1.05
.95
.91
.83
8
10
12
14
16
18
22
24
30
Suggested Minimum Spray Heights
The nozzle height suggestions in the table below are based on the minimum overlap required to
obtain uniform distribution. However, in many cases, typical height adjustments are based on a 1 to
1 nozzle spacing to height ratio. For example, 110° flat spray tips spaced 20 inches apart, are
commonly set 20 inches above the target.
(inches)
TeeJetT Standard, TJ
TeeJet, XR, TX, DG, TJ
TeeJet, XR, DG, TT, TJ, AI
FullJetT
FloodJetT TK, TF
65°
80°
110°
120°
120°
22-249
17-199
16-189
10-189**
14-169***
33-359
26-289
20-229
14-189**
15-179***
NR*
NR*
NR*
14-189**
18-209***
* Not recommended.
** Nozzle height based on 30° to 45° angle of orientation (see page 60 of catalog).
***
Precision Tank & Equipment Co.
Wide angle spray tip height is influenced by nozzle orientation. The critical factor
is to achieve a double spray pattern overlap for TK FloodJet® nozzles.
1
Parts Hotline: 1-800-811-7814
TEEJET – Droplet Size Information
DG TeeJet® Even Flat Spray Tips
Nozzle selection is often based upon droplet size.
The droplet size from a nozzle becomes very
important when the efficacy of a particular crop
chemical is dependent on coverage, or the
prevention of spray leaving the target area is a
priority.
The majority of the nozzles used in agriculture
can be classified as producing either fine,
medium or coarse droplets. Nozzles which
produce fine droplets are usually recommended
for post-emergence applications which require
excellent coverage on leaf surfaces. The most
common nozzles used in agriculture are those
which produce medium-sized droplets. Nozzles
producing medium-sized droplets can be used
for contact and systemic herbicides,
pre-emergence surface applied herbicides,
insecticides and fungicides.
An important point to remember when choosing
a spray nozzle which produces a droplet size in
one of the three categories, is that one nozzle
can produce different droplet size classifications
at different pressures. A nozzle might produce
medium droplets at low pressures, while
producing fine droplets as pressure is increased.
(PSI)
30
35
40
50
60
DG TeeJet® Flat Spray Tips
DG95015E
DG9502E
DG9503E
DG9504E
DG9505E
M
M
M
M
M
C
M
M
M
M
C
C
M
M
M
C
C
C
M
M
C
C
C
C
M
AI TeeJet® Flat Spray Tips
(PSI)
AI11002
AI110025
AI11003
AI11004
AI11005
VC
VC
VC
VC
VC
VC
C
C
C
C
VC
VC
VC
VC
VC
VC
VC
C
C
C
VC
VC
VC
VC
VC
VC
VC
VC
C
C
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
VC
TT11001
TT11015
TT11002
TT11003
TT11004
TT11005
C
M
M
M
M
M
F
F
F
C
C
M
M
M
M
M
M
M
VC
C
C
M
M
M
M
M
M
VC
VC
C
C
C
C
M
M
M
VC
VC
VC
C
C
C
C
C
C
EC
VC
VC
VC
C
C
C
C
C
Droplet size classes are shown in the following
tables to assist in choosing an appropriate
spray tip.
Turbo TeeJet® Flat Spray Tips
(PSI)
Drift Reducing Spray Tips
TF Turbo
FloodJet
TT Turbo
TeeJet
DG TeeJet
XR TeeJet
15
20
30
40
45
50
60
75
90
AI TeeJet
VF
Very Fine
F
Fine
M
Medium
C
Coarse
VC
Very Coarse
EC
Extremely Coarse
Precision Tank & Equipment Co.
30
35
40
50
60
DG80015
DG8002
DG8003
DG8004
DG8005
DG110015
DG11002
DG11003
DG11004
DG11005
M
M
M
M
M
C
C
M
M
M
C
C
C
M
M
C
C
C
C
M
C
C
C
C
M
M
M
M
M
M
C
M
M
M
M
C
C
M
M
M
C
C
C
M
M
C
C
C
C
M
TwinJet® Double Flat Spray Tips
AI110015
30
40
50
60
70
80
90
100
110
120
(PSI)
(PSI)
TJ60-650066
TJ60-6501
TJ60-650134
TJ60-6502
TJ60-6503
TJ60-6504
TJ60-6506
TJ60-6508
VF
VF
VF
VF
VF
F
F
VF
VF
VF
F
F
F
F
F
F
F
F
F
F
M
M
M
M
F
M
M
M
M
M
C
C
M
M
M
C
C
C
C
C
30
35
40
50
60
(PSI)
TJ60-8001 TJ60-8002 TJ60-8003 TJ60-8004 TJ60-8006 TJ60-8008 TJ60-8010 TJ60-11002TJ60-11003 TJ60-11004TJ60-11006TJ60-11008 TJ60-11010
30
35
40
50
60
VF
VF
VF
VF
VF
F
F
F
F
F
F
F
F
F
F
M
M
M
M
F
M
M
M
M
M
C
C
M
M
M
C
C
C
C
C
F
F
VF
VF
VF
F
F
F
F
F
M
M
F
F
F
M
M
M
M
M
M
M
M
M
M
C
C
M
M
M
XR TeeJet® Flat Spray Tips
(PSI)
15
20
30
40
45
50
60
XR8001 XR80015 XR8002 XR8003 XR8004 XR8005 XR8006 XR8008 XR11001 XR110015 XR11002 XR11003 XR11004 XR11005 XR11006 XR11008
M
M
F
F
F
F
F
M
M
M
M
F
F
F
M
M
M
M
M
M
M
C
M
M
M
M
M
M
C
C
M
M
M
M
M
VC
C
C
C
M
M
M
VC
VC
C
C
C
C
C
VC
VC
VC
C
C
C
C
F
F
F
F
F
F
F
M
F
F
F
F
F
F
M
F
F
F
F
F
F
M
M
M
M
F
F
F
M
M
M
M
M
M
M
C
M
M
M
M
M
M
C
C
M
M
M
M
M
C
C
C
C
C
M
M
Turbo FloodJet® Flat Spray Tips
(PSI)
10
20
30
40
50
60
70
80
90
100
27
TF-2
TF-2.5
TF-3
TF-4
TF-5
TF-7.5
TF-10
EC
EC
EC
VC
VC
VC
VC
VC
VC
VC
EC
EC
EC
VC
VC
VC
VC
VC
VC
VC
EC
EC
EC
VC
VC
VC
VC
VC
VC
VC
EC
EC
EC
EC
VC
VC
VC
VC
VC
VC
EC
EC
EC
EC
EC
VC
VC
VC
VC
VC
EC
EC
EC
EC
EC
VC
VC
VC
VC
VC
EC
EC
EC
EC
EC
VC
VC
VC
VC
VC
Parts Hotline: 1-800-811-7814
TeeJet® Standard Flat Spray Tips
(PSI)
30
35
40
50
60
TP8001 TP80015 TP8002 TP8003 TP8004 TP8005 TP8006 TP8008 TP11001 TP110015 TP11002 TP11003 TP11004 TP11005 TP11006 TP11008
F
F
F
F
F
M
M
M
F
F
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
C
C
C
M
M
C
C
C
C
C
VC
VC
C
C
C
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
M
M
M
F
F
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
C
C
C
M
M
Droplet size classifications are based on BCPC specifications and in accordance with ASAE Standard X-572 at the date of printing.
Classifications are subject to change.
Precision Tank & Equipment Co.
28
Parts Hotline: 1-800-811-7814
TEEJET SELECTION GUIDE FOR BANDING and DIRECTED SPRAYING
Contact
Contact
Systemic
Systemic
Contact
Systemic
Helpful Reminders for Band Spraying
Wider angle spray tips allow the spray height to
be lowered to minimize drift.
Example:
Ceramic
Pre-Emerge
Band
Hardened
Stainless
Steel
Available Materials
Liquid
Fertilizer
Stainless
Steel
Insecticides
Polymer
Fungicides
Post-Emerge Band
Brass
Herbicides
80° Even Flat Spray
95° Even Flat Spray
Good
Good
Excellent
Good
Excellent
Good
Good
Good
Excellent
Good
Good
Good
Excellent
Good
Good
Good
Excellent
Good
95°
only
Excellent
Excellent
95°
only
EVEN FLAT SPRAY TIP
EVEN FLAT SPRAY TIP
(At Lower Pressure)
(At Lower Pressure)
Excellent
(At Lower Pressure)
Excellent
(At Lower Pressure)
AIR INDUCTON EVEN FLAT SPRAY TIP
Excellent
Excellent
Excellent
Excellent
Good
Excellent
Excellent
The spray angle of the nozzle and the resulting
band width are directly influenced by the spraying
pressure.
Example: 8002E Even Flat Spray
15 PSI
40 PSI
TWIN EVEN FLAT SPRAY TIP
Use care when calculating Field Acres vs.
Treated Acres.
HOLLOW CONE SPRAY TIP
Excellent
FULL CONE SPRAY TIP
Excellent
Excellent
UNDERLEAF SPRAY TIP
Excellent
Excellent
Good
Excellent
Good
Core
only
SPRAY TIP
Field Acres = Total Acres of Planted Cropland
Band Width
Treated Acres = Field Acres X —————
Row Spacing
Broadcast
Banding
*Note: Consult the chemical manufacturer’s product label for specific rate and application recommendations.
Even Flat
Spray Tip
Drift Guard
Even Flat Spray Tip
Hollow Cone
Spray Tip
Ideal for banding over the row
or in row middles
Ideal for banding over the row or in row middles
Uniform coverage across
spray pattern
Excellent for band application of surface
applied herbicides
Spraying pressure –
20-60 PSI (1.4-4 bar)
95° spray angle
Underleaf Banding
Spray Tip
Ideal for banding herbicides and
insecticides with 3 nozzles over the row
Off-center tip with tapered flat spray
characteristics
Small droplets
85° spray angle
Spraying pressure – 30-300 PSI (2-20 bar)
Uniform distribution
Spraying pressure – 20-60 PSI (1.5-4 bar)
Pre-orifice design produces larger
droplets to reduce drift
Ideal for banding (2 tips) and as an end nozzle
on plot sprayers and spraying close to water
Spraying pressure – 30-60 PSI (2-4 bar)
Relative droplet size for each
spray tip is shown in each pattern.
Air Induction Even Flat
Spray Tip
Large, air-filled drops
Larger drops for less drift
Spraying pressure – 30-100 PSI
(3-8 bar)
Full Cone
Spray Tip
Twin Even
Flat Spray Tip
Ideal for banding over the row
or in row middles
Larger, penetrating droplets
Excellent for systemic
growth regulators
Smaller droplets for thorough
coverage
Typically used in 3 nozzles
over the row configuration
Penetrates crop residue or
dense foliage
Spraying pressure–
20-80 PSI (1.4-5.5 bar)
40° or 80° spray angles
Spraying pressure – 30-60 PSI (2-4 bar)
Precision Tank & Equipment Co.
29
Parts Hotline: 1-800-811-7814
Precision Tank & Equipment Co.
Spray Tip
Excellent wear life–ideal for abrasive
spray materials using ceramic material
Produce smaller droplets for
thorough coverage with contact
insecticides, fungicides, miticides
and foliar nutrients
Spraying pressure – 10-300 PSI
(.7-20 bar)
30
Full Cone
Hollow Cone
Parts Hotline: 1-800-811-7814
QUICK TEEJET CAPS
Quick
TeeJet
Cap
The Quick TeeJet caps are designed with grooves that fit locating lugs
on the nozzle body. Caps are made of nylon and are available for use
with all TeeJetT spray tips. Maximum operating pressure of 300 PSI.
CP19438-EPR
(EPDM Standard)
Seat
Gasket
CP19438-VI
(Viton Optional)
Quick TeeJet Cap and Seat Gasket Set
Quick TeeJet
CAP Model#
TeeJet Flat Spray Tips
(Smaller Capacities)
25612
Standard
–0067 Thru
–08
XR
–01 Thru
–08
DG
–015 Thru
–05
TT
–01
Thru –08
TeeJet Flat Spray Tips
(Larger Capacities)
Standard
–10 Thru
–20
XR
–10 Thru
–15
25610
TJ TwinJet®
No. TJ60
Spray Tip
AI TeeJet®
No. AI
Spray Tip
25598
Turbo FloodJet®
VisiFloT Spray Tip
TK-VS FloodJet®
VisiFlo Spray Tip
Locating
Nib
25600
Colors of
Quick TeeJet Caps
Color
Code
Colors of
Quick TeeJet Caps
Color
Code
Black
White
Red
Blue
1
2
3
4
Green
Yellow
Brown
Orange
5
6
7
8
Precision Tank & Equipment Co.
*Specify color-code (see chart). Unless otherwise specified, a yellow (6) cap will be supplied.
**These Quick TeeJet caps available only in black.
† Polypropylene Quick TeeJet caps available only
in gray and are rated to 150 PSI.
1
How to order:
For cap and seat gasket set, specify set no.
and color-code.
Example: 25612-3-NYR
For cap only, specify part no. and color-code.
Example: CP25597-4-NY
For seat gasket, specify part no.
Example: CP19438-EPR
Parts Hotline: 1-800-811-7814
QUICK TEEJET CAPS
The Quick TeeJet caps are designed with grooves that fit locating lugs
on the nozzle body. Caps are made of nylon and are available for use
with all TeeJetT spray tips. Maximum operating pressure of 300 PSI.
Quick
TeeJet
Cap
CP19438-EPR
(EPDM Standard)
Seat
Gasket
CP19438-VI
(Viton Optional)
Quick TeeJet Cap and Seat Gasket Set
Quick TeeJet
CAP Model#
TK FloodJet
TX ConeJet
FL FullJet
TG Full Cone
25608
Seal
Core
D-Disc
Core
CP18999-EPR†
(EPDM standard)
CP18999-VI†
(Viton optional)
†Used with Disc-Core
Sprays (Insert Core
into Seal)
Ceramic Disc-Core
D-Disc
Core
26278
Permits use of standard 1⁄89 and 1⁄49 nozzles.
Can be used for mounting pressure gauge at
the nozzle. See Data Sheet No. 20055 for more
information.
Provides shutoff at nozzle for quick
spacing change or change in spray swath.
45° Quick TeeJet cap
90° Quick TeeJet cap
Colors of
Quick TeeJet Caps
Color
Code
Colors of
Quick TeeJet Caps
Color
Code
Black
White
Red
Blue
1
2
3
4
Green
Yellow
Brown
Orange
5
6
7
8
Precision Tank & Equipment Co.
*Specify color-code (see chart). Unless otherwise specified, a yellow (6) cap will be
supplied.
**These Quick TeeJet caps available only in black.
† Polypropylene Quick TeeJet caps available
only in gray and are rated to 150 PSI.
1
How to order:
For cap and seat gasket set, specify set no.
and color-code.
Example: 25612-3-NYR
For cap only, specify part no. and color-code.
Example: CP25597-4-NY
For seat gasket, specify part no.
Example: CP19438-EPR
Parts Hotline: 1-800-811-7814
TEEJET – Even Flat Spray Tips
Typical Applications:
Features:
See selection guide for recommended typical
application for TeeJet.
Ideal for banding over the row or
How to order:
Provides uniform distribution throughout
in row middles
the flat spray pattern
Specify tip number.
Examples:
Easily mounted on spray boom or planter
TP8002E-VS-Stainless Steel with
VisiFlo color-coding
TP8002E-SS-Stainless Steel
Available in VisiFlo® color-coding in
stainless steel, hardened stainless
steel and brass
CONEJET – VisiFlo Hollow Cone Spray Tips
Typical Applications:
See selection guide on pages 64 and
65 for recommended typical application
for ConeJet.
Features:
VisiFloT color-coded version consists
of stainless steel or ceramic orifice in
polypropylene body. Maximum
operating pressure 300 PSI. Spray
angle is 80° at 100 PSI
Ideal for banding with two or three nozzles
over the row
Finely atomized spray pattern provides
thorough coverage
Standard ConeJet (not color-coded)
available in brass and stainless steel in
a wide range of capacities with 65° (TY)
and 80° (TX) spray angles
How to order:
Specify tip number.
Examples:
TXVS-4 – Stainless Steel with
VisiFlo color-coding
TX-4
– Brass
TX-SS4 – Stainless Steel
TX-VK4 – Ceramic with VisiFlo
color-coding
Also available TX-VS1 and TX-VS2
(not shown)
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
STREAMJET – Solid Stream Spray Nozzles
Stainless Steel for
Banding Fertilizers
Permits banding fluids
at high rig speeds.
Large orifices with no
internal obstructions permit
non-clogging suspension
applications.
Lower drift potential.
Reference pages 124-142
for more information.
TEEJET – Flow Regulators
CP4916
Orifice
Plate
How to order: Specify orifice plate number. Example: CP4916-8
TEEJET ORIFICE DISCS – Disc-Core Type Cone Spray Tips
For spraying pesticides at higher pressures
and flow rates. Especially suitable for
wettable powders and other abrasive
chemicals. Larger capacity nozzles are
also used in air blast sprayers.
Produce smaller droplets for thorough
coverage with contact pesticides and
foliar applications.
Maximum spray pressure to
300 PSI (20 bar).
Orifice Discs
Stainless
Steel
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
TEEJET – Hose Drops
Hose drops connect to standard and
Quick TeeJet nozzle bodies and can also be
used with swivels. Available in 159
(380 mm) and 249 (610 mm) lengths.
Maximum operating pressure 125 PSI.
Note: QJ1⁄4T-NYB can be attached to hose
drops for use with Quick TeeJet caps.
TEEJET – Tip Strainers
TeeJet Strainers...with VisiFlo® color-coding
Nylon slotted and polypropylene wire mesh strainers are
color-coded for easy identification of strainer mesh size.
TEEJET – Container Rinsing Nozzles
23240
The 23240 container rinsing
nozzle is used to rinse residue
from containers before disposal
Can be used for containers with
11⁄32” diameter openings or larger
Three flat spray orifices provide
self-rotational forces needed to
create spherical coverage
Made of 303 stainless steel with hardened stainless
steel bearings and races for maximum wear life. Also
includes an internal sleeve made of Teflon
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
TEEJET – Swivel Nozzle Bodies
Quick TeeJet® Swivel Nozzle
Bodies
QJ8600-1⁄4-NYB
Single Swivel Nozzle
QJ8600-2-1⁄4-NYB
Double Swivel Nozzle
QJ8600 swivel Quick TeeJet nozzle body
assemblies provide the same spray tip
adjustability of a standard TeeJet
threaded swivel plus the quick change
and self-aligning features of the
Quick TeeJet System.
TEEJET – ChemSaver Diaphragm Check Valves
8360
12328-NYB
QJ8360-NYB
TEEJET – ChemSaver Air Shutoff Valve
No. 6227 Diaphragm
Teflon (optional)
To be used with
No. 21953 Diaphragm
No. 21953 Diaphragm
EPDM or Viton
Note: Nib on diaphragm
fits into hole in end
cap assembly.
The 39535 ChemSaver Air
Shutoff valve is designed as a
pneumatic valve for use on
TeeJet nozzle body assemblies.
The air pressure is used to
open the valve and a spring to
close the valve.
39535 ChemSaver
Air Shutoff Valve
Clamp Assemblies
Consist of upper and lower clamps and bolt for use with hose shank nozzle bodies.
AA111
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
QUICK TEEJET – Multiple Nozzle Bodies & Assemblies for Dry Booms
QJ360 Nozzle Body Series for Dry Boom
Available with either 3, 4 or 5 spray positions for
easy change of spray tips or quick boom flushing
Includes ChemSaver® diaphragm check valve for
drip-free shutoff
Positive shutoff between each spray position
Durable design mounts body high on boom structure
for maximum protection
Maximum operating pressure of 300 PSI (20 bar)
Available in 1⁄2”, 3⁄4” or 1” single or double hose shanks
QJ363
3 Spray Outlets
Standard EPDM diaphragm with Viton® available
as an option
QJ364
4 Spray Outlets
QJ365
5 Spray Outlets
Triple Nozzle Body
Designed to greatly simplify changing
spray tips in the field
available as an option
Provides three spray positions for
easy change of spray tips or quick
boom flushing
Positive shutoff between each
spray position
24230
Includes ChemSaver® diaphragm
check valve for drip-free shutoff
Precision Tank & Equipment Co.
Standard EPDM diaphragm with Viton
1
Can be used with all Quick TeeJet caps
Nylon body
Maximum operating pressure of 125 PSI
(9 bar)
Available in 1⁄2” and 3⁄4” single or double
hose shanks
Parts Hotline: 1-800-811-7814
QUICK TEEJET – Multiple Nozzle Bodies & Assemblies for Dry Booms
QJ100 Series
Quick TeeJet®
Nozzle Assemblies
In sizes to fit 1⁄2”, 3⁄4”, 1” and 11⁄4” pipe and
equivalent size tubing. Also for 3⁄4”, 1”, 11⁄4”
and 11⁄2” sq. tubing. Hose barb sizes for 3⁄8”,
1⁄2” or 3⁄4” I.D. hose. Available in single, double,
or triple hose shanks. Max. operating pressure
– 125 PSI (9 bar).
QJ100 Series are available in polypropylene
and are rated to 125 PSI.
QJ200 Series Diaphragm Check Valve
Quick TeeJet® Nozzle Assemblies
Drip-free shutoff. Opening pressure –
10 PSI (0.7 bar). Standard diaphragm is
EPDM with VitonT optional. Max. operating
pressure – 125 PSI (9 bar). Available in
same sizes as Type QJ100 Series. Available
in single, double or triple hose shanks.
QJ300 Series
Diaphragm Check Valve
Quick TeeJet® Nozzle Assemblies
Low profile design allows maximum protection
against damage. Available with single and
double hose shanks for 1⁄2”, 1⁄2” and 1⁄2” I.D.
hose. Drip-free shutoff. Opens at 10 PSI
(0.7 bar). Standard diaphragm is EPDM with
Viton® optional. Maximum operating pressure
is 300 PSI (20 bar).
QJ300 Series are available in polypropylene
and are rated to 150 PSI.
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
QUICK TEEJET – Multiple Nozzle Bodies & Assemblies for Wet Booms
QJ360 Nozzle Body Series
for Wet Booms
Available with either 3, 4 or 5 spray positions for
easy change of spray tips or quick boom flushing
Positive shutoff between each position
Maximum operating pressure of 300 PSI (20 bar)
Available in 20 mm, 25 mm, 1⁄2”, 3⁄4” or 1” pipe
connections
Includes ChemSaver® diaphragm check valve for
QJ365
QJ363
drip-free shutoff
Standard EPDM diaphragm with Viton® available
as an option
QJ360 Nozzle Bodies Available Upon Request
QJ364
Type 24216-NYB
Can be mounted to 1⁄2”, 3⁄4” or 1” pipe or
Provides three spray positions for easy
Maximum operating pressure of 150 PSI
(10 bar)
change of spray tips
Shutoff position provided between each
spray position
Features ChemSaverT drip-free shutoff.
24216
Standard diaphragm of EPDM with optional
VitonT available
equivalent size tubing
1⁄2” and 3⁄4” sizes include mounting hole
in upper clamp subassembly for attachment to flat surfaces
Requires 10 PSI (0.7 bar) at the nozzle to
open check valve
Type QJ22187-NYB
Can be mounted to 1⁄2”, 3⁄4” or 1” pipe or
equivalent size tubing
1⁄2” and 3⁄4” sizes include a mounting hole
in clamp subassembly for mounting to flat
surfaces
QJ22187
Allows side mounting to flat surface for
Requires 10 PSI (0.7 bar) at the nozzle to
open check valve
Standard diaphragm of EPDM with optional
Viton® available
Maximum operating pressure of 300 PSI
(20 bar)
protection of nozzle body
Features ChemSaver drip-free shutoff.
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
QUICK TEEJET – Multiple Nozzle Bodies & Assemblies for Wet Booms
Type QJ17560-NYB
Can be mounted to 1⁄2”, 3⁄4” or 1” pipe or
Maximum operating pressure of 300 PSI
(20 bar)
equivalent size tubing
Features ChemSaver drip-free shutoff.
1⁄2” and 3⁄4” sizes include a mounting
hole in upper clamp subassembly for
mounting to flat surfaces
Requires 10 PSI (0.7 bar) at the nozzle to
open check valve
Standard diaphragm of EPDM with optional
Viton available
QJ17560
Type QJ7421-NYB
Can be mounted to 1⁄2”, 3⁄4” or 1” pipe
1⁄2” and 3⁄4” sizes include a mounting
or equivalent size tubing.
Maximum operating pressure of 300 PSI
hole in upper clamp subassembly for
mounting to flat surfaces.
(20 bar)
QJ7421
QJ1⁄4T-NYB
QJ1⁄4TT-NYB
QJT-NYB
Allows use of Quick TeeJet system with 1⁄4”
NPT and BSPT male connections
Permits use of Quick TeeJet system with
standard 11⁄16”-16 TeeJet thread
Allows use of Quick TeeJet system with
1⁄4” NPT and BSPT female connections
Maximum operating pressure of 300 PSI
(20 bar)
Allows use of Quick TeeJet system with
1⁄4”
22674-1⁄4-NYB
NPT female connections
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
DIRECTOVALVE – AA440 Manifold
Options Available:
Inlet Connections:
The TeeJetT AA440 series DirectoValve manifold provides a convenient, compact solution for the installation of AA344 electric ball valves.
This system eliminates the need for custom fabrication of pipe or hose
manifolds, drastically reducing both installation time and the chance
for fluid leaks. The AA440 manifold provides the high performance of
electric ball valves with the ease of installation previously found only
with solenoid valves.
– 1” through 11⁄4” straight hose barb
– 1⁄4”, 3⁄8” and 1” NPT (F) threaded inlets
Outlet Connections:
– 3⁄4” and 1” NPT (F) threaded outlets
– 50 Series flanged fittings
(refer to page 26 for 50 Series flanged fittings options)
How to order:
More options may be available. For more information on how
to order your 440 manifold, contact Precision Tank & Equipment.
– Quick Connect outlet connections
(refer to page 26 for Quick Connect options)
DIRECTOVALVE – 2-Way Electric Control Ball Valves
AA344AEC
AA344AE
Remote Control Electric Ball Valves
Remote Control Electric Ball Valves
Works with a simple, single pole
3⁄49 or 19 NPT & BSPT (F) connection
off/on switch
Wetted parts: nylon, Teflon®,
No external fuses — incorporates an
polypropylene and VitonT
internal resettable fuse (disconnect
power to valve for 20 seconds to reset)
Works with double-pole,
double-throw system
Also available with electrical connec-
No external fuses — incorporates
tors for simple installation with TeeJet®
sprayer controls
5 PSI (0.35 bar) pressure drop for 32 GPM (121 l/min) flow
Quick connect and 50 Series flanged outlets are available
(See page 26 for options)
an internal resettable fuse (disconnect
power to valve for 20 seconds to reset)
5 PSI (0.35 bar) pressure drop for 32 GPM (121 l/min) flow
Maximum pressure rating of 300 PSI (20 bar)
How to order:
Example: AA344AE-2-3⁄4 or AA344AE-2-1
Maximum pressure rating of 300 PSI (20 bar)
Available in BSPT.
How to order:
Example: AA344AEC-2-3⁄4 or AA344AEC-2-1
Available in BSPT.
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
DIRECTOVALVE – 2-Way Electrically Operated Solenoid Valves
AA144A-, AA145-, AA146- DirectoValve Control Valves
Direct acting; large internal flow chamber without pilot hole reduces
Encapsulated solenoid coil can be changed without removing valve
chance of clogging
from system
Stainless steel wetted parts provide additional corrosion
EPDM diaphragms and seat washers, Viton® optional
resistance
Continuous flow through bypass connection, with flow to spray line
Operate on 12 volt DC system
controlled by valve “on-off” action
AA144A Valve for pressures up to 100 PSI
10 GPM (37.9 l/min) flow with only
Fabric reinforced EPDM diaphragms
5 PSI (0.35 bar) pressure drop
Also available as 2-unit or 3-unit assembly
Can be ganged with other 144A
Spray Lines
DirectoValve control valves
2.5 amp current draw
Continuous
By-Pass
Inlet
AA144A-1
Polypropylene body for chemical resistance
How to order:
To order, specify AA144A- then “1”, “2”
or “3” to indicate number of units.
Example: AA144A-3
Model
No.
Inlet
Size
Outlet
Size
Flow Rate at 5 PSI
Pressure Drop
Maximum
Pressure
AA144A-*
3⁄4”
1⁄2”
10 GPM
100 PSI
Current
Draw
2.5 amp
Available in BSPT.
AA144A-3
(Three Unit)
Model AA344AE-2RB
Pressure Regulating Butterfly Valve
The AA344AE-2RB pressure regulating valve
has all the features and reliability of a ball
valve, plus smooth linear flow regulation at
lower flows (i.e. less than 5 GPM). Pressure
drop of 5 PSI (0.35 bar) at 30 GPM (113 l/min).
Maximum operating pressure of 300 PSI
(20 bar). A cycle time from fully open to closed
in 6 seconds. Continuous bypass in closed
position is 1.4 GPM (5.3 l/min). Available with 3⁄49 and
19 connections NPT or BSPT (F) or Quick Connections.
How to order:
Specify model number.*
Examples: AA344AE-2RB-3⁄4 or AA344AE-2RB-1
Model AA344AE-2RL
Pressure Regulating Valve
Larger capacity than the 344AE-2PR with a
pressure drop of 5 PSI (0.35 bar) at 27 GPM
(102 l/min) and a cycle time from fully open
to closed in 12 seconds. Maximum pressure
rating of 300 PSI (20 bar).
How to order:
Specify model number.*
Examples: AA344AE-2RL-3⁄4 or AA344AE-2RL-1
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
QUICK TEEJET – Multiple Nozzle Bodies & Assemblies for Wet Booms
Type QJ17560-NYB
Can be mounted to 1⁄2”, 3⁄4” or 1” pipe or
Maximum operating pressure of 300 PSI
(20 bar)
equivalent size tubing
Features ChemSaver drip-free shutoff.
1⁄2” and 3⁄4” sizes include a mounting
hole in upper clamp subassembly for
mounting to flat surfaces
Requires 10 PSI (0.7 bar) at the nozzle to
open check valve
Standard diaphragm of EPDM with optional
Viton available
QJ17560
Type QJ7421-NYB
Can be mounted to 1⁄2”, 3⁄4” or 1” pipe
1⁄2” and 3⁄4” sizes include a mounting
or equivalent size tubing.
Maximum operating pressure of 300 PSI
hole in upper clamp subassembly for
mounting to flat surfaces.
(20 bar)
QJ7421
QJ1⁄4T-NYB
QJ1⁄4TT-NYB
QJT-NYB
Allows use of Quick TeeJet system with 1⁄4”
NPT and BSPT male connections
Permits use of Quick TeeJet system with
standard 11⁄16”-16 TeeJet thread
Allows use of Quick TeeJet system with
1⁄4” NPT and BSPT female connections
Maximum operating pressure of 300 PSI
(20 bar)
Allows use of Quick TeeJet system with
1⁄4”
22674-1⁄4-NYB
NPT female connections
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
GUNJET – Regular & Low Pressure Spray Guns
No. AA43L for operating pressures up to 200 PSI.
AA43 GunJet
Designed and built for heavy duty service. Stem extends through extension to valve seat
located directly behind orifice disc for drip-free shutoff and instant operating response.
Convenient trigger-lock for continuous spraying.
Exposed Packing Nut for easy adjustment of packing
Choice of Materials: Brass or aluminum
AA23L-7676
The AA23L-7676 GunJet spray gun (shown above) is also available without extension as
GunJet spray gun AA23L. Flow rates up to 5 GPM (19 l/min). Maximum operating pressure –
250 PSI (17 bar). Inlet 1⁄49 NPS (M) thread. Strong aluminum alloy body. When used with
extension the valve stem extends through the entire extension length for drip-free shutoff
immediately behind the spray tip. Accommodates all interchangeable TeeJet spray tips.
TEEJET – Calibration/Adjustment Accessories
TeeJet Tip Cleaning Brush
The TeeJet Calibration Container features a 60
oz. capacity and a dual scale in both U.S. and
metric graduations. The container is molded in
polypropylene for excellent chemical resistance
and durability.
TeeJet Calibration Container
How to order:
Example: CP24034-PP
TeeJet Tip Tester
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
ANHYDROUS AMMONIA VALVES
Rego Globe Valves
Continental Globe Valves
Rego Quick Acting Globe Valves
Rego Angle Valves
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
ANHYDROUS AMMONIA VALVES
Henry Angle Valves
Rego Quick Acting Angle Valves
Pressure Relief, Internal
Pressure Relief, External
Hydrostatic Relief
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
ANHYDROUS AMMONIA VALVES
Vent/Bleeder
Fill/Withdrawal
Miscellaneous Anhydrous Ammonia Valve Parts
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
BALL VALVES & REPAIR KITS
Valvtec
* Other Valvtec Valve parts are in stock
Apollo Valves - Carbon Steel
Apollo Valves - Stainless Steel
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
BALL VALVES & REPAIR KITS
Apollo Valve Accessories
Stainless Steel Valves
BANJO Ball Valves
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
BALL VALVES & REPAIR KITS
BANJO Ball Valves – Replacement Parts
* Valve Repair Kits contain items noted with asterisk –
1 Ball, 2 Ball Seats, 2 Body O-Rings, 1 Upper Stem
Bushing, 1 Thrust Washer, 1 Stem O-Ring
BANJO 2" Full Port Ball Valves
BANJO Replacement Parts for VSF200 "Stubby Valve"
* Valve Repair Kits contain items noted with asterisk –
1 Ball, 2 Ball Seats, 1 Body Gasket, 1 Upper Stem
Bushing, 1 Thrust Washer
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
BALL VALVES & REPAIR KITS
BANJO Replacement Parts for VSMT200 "Stubby Valve"
* Valve Repair Kits contain items noted with asterisk – 1 Ball, 2 Ball Seats, 1 Body Gasket, 1 Upper Stem Bushing, 1 Thrust Washer
BANJO Replacement Parts for VSFMT200 "Stubby Valve"
* Valve Repair Kits contain items noted with asterisk – 1 Ball, 2 Ball Seats, 1 Body Gasket, 1 Upper Stem Bushing, 1 Thrust Washer
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
BALL VALVES & REPAIR KITS
BANJO 3-Way Poly Ball Valves/Bottom Load
* Direction flow either right or left. Valve can be turned off to stop flow.
BANJO 3-Way Poly Ball Valves/Side Load
* Direction flow either right or left. Valve cannot be turned off.
BANJO Single Union Polypropylene Ball Valves
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
BALL VALVES & REPAIR KITS
BANJO Single Union Polypropylene Ball Valves – Replacement Parts
BANJO Polypropylene Nozzle Valves
Miscellaneous Ball Valves
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
BALL VALVES & REPAIR KITS
Gromo Actuated Ball Valves
Gromo Valve Parts
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
12V SOLENOID & MOTORIZED BALL VALVES
Delevan
Dema
Humphrey
Banjo
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
12V SOLENOID & MOTORIZED BALL VALVES
Spraying Systems
KZ Motorized Ball Valves
KZ EH2 ‘88’ Series Valve Parts
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
12V SOLENOID & MOTORIZED BALL VALVES
KZ EH2 ‘99’ Series Valve Parts
BUTTERFLY VALVES
Ultraflo & Centerline Butterfly Valves
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
BUTTERFLY VALVES
Ultraflo/Keystone Actuators & Parts
Centerline Actuators & Parts
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
CHECK VALVES
Miscellaneous Check Valves
MISCELLANEOUS VALVES
Hydraulic Valves
Gate Valves - Brass
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
MISCELLANEOUS VALVES
Dump Valves
DEFCO Valves
Miscellaneous Valves
* Other valves are available upon request.
NH3 KNIVES
NH3 Knives
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
CONTINENTAL NH3 METERS
C-4100 Series Meter-Matic Parts
01-3118-25
01-93
01-21
01-64-F
65-20
01-94-F
01-04
01-30B
01-92
65-11B
01-22
65-13
01-97
01-30DS
01-31
01-86-F
01-14
01-87
41-84F
01-95
01-70-F
01-60-F
65-75
65-71BF
65-33B
01-832-25
A41-82BF
A-41-41
01-89
65-19
41-83-FX
65-18
41-53
41-73
41-02A
A41-24
41-15
01-92-BF
65-34
01-85F
01-2520-125
01-88
A-41-01
41-03A
01-80
01-2520-100
65-91
41-26
Precision Tank & Equipment Co.
41-72
41-39
01-71BF
65-81
65-35
A-65-37
1
Parts Hotline: 1-800-811-7814
CONTINENTAL NH3 METERS
"C" Series Meter-Matics
(1) Maximum flow capacity is 2,500# nitrogen per
hour at 100# tank pressure.
(2) Maximum flow capacity is 750-4,200# nitrogen
per hour at 100# tank pressure.
Note: All C-Series Meter-Matics are calibrated with Continental fittings at 100# tank pressure with 12 foot 1" hose, hose line valve and 1"
quick disconnect coupler. Subtract 10% from chart flow capacity if using 1-1/4" quick disconnect coupler.
A-EQ-2000 Equalizer & Parts
Continental A-MVD Manifold
Continental 6006 & 6007 Series Manifolds
* All 6007 Series Manifolds are available with a built-in strainer screen.
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
CONTINENTAL NH3 METERS
Continental B-9500 Super Flow Meter & Parts
197-3816-150
01-94-F
01-85-F
09-05-R
09-Q4113
197-Q4139
09-640
09-441
09-440
09-540
09-Q4116
197-700
ROTATED 180°
09-140
09-241
09-240
09-8114
09-141
657-2
A-09-82-BF
09-2520-75
01-88
09-77
01-89
09-06
01-71BF
A-09-41
09-18
09-19
09-39
09-01
09-83-F
09-73
09-87
09-375-75
09-91
09-3816-275
09-74
09-60
A-6135
09-04-R
09-76
09-80
09-60
09-92
09-90
09-32
09-72
09-33
09-34
09-02
09-13
09-375-150
09-50
09-63-F
01-2520-100
Note: The B-9500 Super Flow Meter is calibrated with Continental fittings at 100# tank pressure with 12 foot 1-1/4" hose, hose line valve and
1-1/4" quick disconnect coupler.
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
STRAINERS
Line Strainers
Strainer Replacement Parts
BANJO Poly "T" Strainers
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
STRAINERS
BANJO Poly "T" Strainer Replacement Parts
BANJO Poly "T" Strainers – 316 SS Head w/Poly Bowl
BANJO Poly "T" Strainer Replacement Parts – 316 SS Head w/Poly Bowl
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
STRAINERS
BANJO LSQ Series Poly Strainers
BANJO LSQ Series Poly Strainers Replacement Parts
BANJO 3" Stainless Steel "Y" Strainers & Parts
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
STRAINERS
Paget Strainers & Parts
Morrison Strainers & Parts
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
STRAINERS
HYPRO Strainers & Parts
JFW Strainers & Parts
Other Strainers & Parts
E-Z Clean Load-Out Filter
The E-Z Clean Strainer is available in a variety of configurations.
Inlet: 3" or 4"; Flanged, threaded or barbed
Outlet: 3" or 4; Flanged, threaded or barbed
Material: Screen – 3" or 4" Stainless Steel; Body – Stainless Steel or BI
* Other sizes are available, but normally not required. Contact us for your special applications.
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
STRAINERS
Basket Strainer
Bulk Stainless Steel Wire Cloth
GAUGES & INSTRUMENTATION
Pressure Gauges
* Other pressure ranges available, as well as other
connections. All Stainless Steel gauges available.
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
GAUGES & INSTRUMENTATION
Gauge Protectors & Dampers
Thermometers
* Dial Thermometers with various stem lengths and degrees are available.
Hydrometers
* Other specific gravity’s available.
Pyrometers
* Other degree ranges also available for remote temperature indication.
Float Gauges
* Other degree ranges also available for remote temperature indication.
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
GAUGES & INSTRUMENTATION
Dials
Flow Indicators
Gauge Adapters
* Scales – Beam and Load cell type scales are available in a variety of sizes from various manufacturers.
* Meters – Many meter combinations are available. Call for your required design.
* Gauge Weather Guards – Please specify gauge diameter.
* Liquid Level Gauges – Rotogauges also available.
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
HOSE
Hydraulic Hose
Vinyl and EVA Hose
EPDM Suction Hose (Wire Reinforced)
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
HOSE
Rubber Discharge Hose
EPDM Discharge Hose
PVC Discharge Hose
Anhydrous Ammonia Hose
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
HOSE
Lawn Care Hose
HOSE BARB/KING NIPPLE
Bandit
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
HOSE BARB/KING NIPPLE
Steel
Nyglass
Weld Type King Nipple
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
HOSE BARB/KING NIPPLE
Hose Menders
Nylon
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
HOSE BARB/KING NIPPLE
Nylon, 90˚ Barb
Polypropylene
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
HOSE BARB/KING NIPPLE
Stainless Steel King Nipple
Pushlok Tubing & Fittings
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
HOSE BARB/KING NIPPLE
Air Hammer Fittings
* Other sizes and 4 Lug units available.
QUICK COUPLERS
Adapter A
Coupler B
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
QUICK COUPLERS
Coupler C
Coupler D
Adapter E
Adapter F
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
QUICK COUPLERS
Dust Plug
Dust Cap
* Also available: Arms, pins, gaskets, elbow style couplers and
adapters in various sizes and materials.
Nyglass Elbow Adapters
Yellow Polypropylene Adapters
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
QUICK COUPLERS
90˚ Poly Adapters & Couplings
Quick Coupler Gaskets & Shims
* Arms & pins also available for couplers. Please specify size and
coupler material.
Dry Disconnects
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
QUICK COUPLERS
Pioneer
ACME FITTINGS
Acme Adapters
Acme Hose Coupling
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
ACME FITTINGS
Acme Cap & Plug
NH3 HOSE BARB COUPLING
NH3 Hose Couplings, Barbs & Clamps
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
CLAMPS
Screw Clamps, All Stainless
T-Bolt Clamps
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
CLAMPS
Bandit Clamps
Punchlok Clamps
Bolt Clamps
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
CLAMPS
Muffler Clamps
Clamp Tools
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
METAL and PVC PIPE & FITTINGS
Black, Stainless Steel and PVC Pipe
Stainless Steel Tubing
* Bushings – Please specify size required for male pipe thread x female
pipe thread. Nylon and Polypropylene are also in stock.
Caps
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
METAL and PVC PIPE & FITTINGS
Couplings & Half Couplings
* Reduced Couplings – Please specify size required. Polypropylene also available.
Cross
Ell, 45˚
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
METAL and PVC PIPE & FITTINGS
Ell, 90˚
Blind Flanges
St. Ell, 90˚
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
METAL and PVC PIPE & FITTINGS
Tees
Hex Unions
H-Bar Unions
St. Ell, 45˚
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
METAL and PVC PIPE & FITTINGS
Side Outlet Ell
Side Outlet Tees
* Reducing Tee & Reducing Ell (Black Standard) – Please specify size
required
* Branchlet & Threadolet (Black Sch40) – Please specify size required
Weld Ell, 45˚
Long Radius Weld Ell, 90˚
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
METAL and PVC PIPE & FITTINGS
Weld Tees
Concentric Weld Reducing Couplings
Stub Ends
* Other fittings and materials available. Contact us for current price and
availability.
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
METAL and PVC PIPE & FITTINGS
Backup Flanges (For use w/Stub Ends)
Companion Flanges
Slip On Flanges
Weld Spud Flanges
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
METAL and PVC PIPE & FITTINGS
Nipples
* Custom length nipples and pipe are available.
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
METAL and PVC PIPE & FITTINGS
Plugs
STAINLESS STEEL FLEX CONNECTORS
Miscellaneous Stainless Steel Flex Connectors
* Other sizes available.
* Other fittings are available:
Stainless Steel Backing Rings
Weld Cross
PVC Pipe Nipples
Threaded PVC Fittings
Half Couplings
Victaulic Connectors
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
NYLON PIPE FITTINGS
Nylon Couplings
Nylon Elbows, 90˚
Nylon Street Elbows, 45˚
Nylon Street Elbows, 90˚
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
NYLON PIPE FITTINGS
Nylon Tees
* Nylon Bushings – Most available sizes are in stock. Please specify
MPT x FPT.
Nylon Nipples
POLYPROPYLENE PIPE FITTINGS
Polypropylene Caps
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
POLYPROPYLENE PIPE FITTINGS
Polypropylene Crosses
Polypropylene Couplings
Polypropylene Reduced Couplings
Polypropylene Elbows, 90˚
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
POLYPROPYLENE PIPE FITTINGS
Polypropylene Street Elbows, 45˚
Polypropylene Street Elbows, 90˚
Polypropylene Tees
Polypropylene Companion Flanges
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
POLYPROPYLENE PIPE FITTINGS
Polypropylene Plugs
Polypropylene Reducing Nipples
Polypropylene Nipples
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
PIPE & FITTING SUPPLIES
Pipe Compound
Teflon Tape
PVC Glue & Cleaner
Flange Gaskets
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
CYLINDERS
Hydraulic Cylinders & Parts
* Dayco and Synflex hydraulic fittings are in stock for custom hydraulic hoses. Hydraulic adapters also are in stock for most applications.
MISCELLANEOUS NOZZLES & ACCESSORIES
Nozzle Equipment
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
HYDRAULIC PUMPS & CYLINDERS
Hydraulic Pumps
* A large variety of hydraulic pumps and mounting
kits are available. Please call for application.
Air Cylinders, Switches & Regulators
TANK ACCESSORIES
Poly Tank Fittings
* Spargers – Call for replacement spargers and sparger
fittings.
* Mild steel and stainless steel weld-on and band-on
skids are available in a variety of thicknesses for our
horizontal applicator/nurse tanks.
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
TANK ACCESSORIES
Manholes
Sight Gauges
Fliptops
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
LAWN CARE EQUIPMENT
Lawn Gun Parts
Hose Reels
* Other sizes of hose and name brand hose reels are available.
Swivels
* Poly, stainless steel and galvanized hand tank sprayers are available, as
well as replacement parts for them.
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
TEEJET® GUIDELINE GUIDANCE SYSTEM
Features
• Straight-line, curved and center pivot guidance
• Set up and run with as few as 2 keystrokes
• Easy-to-see lightbar can be mounted inside or outside
• Instant reporting on the lightbar
• Saves time, extremely accurate
• Cheaper than running foam markers
• Records what’s been done to a data card
• See application maps of your field created in real time
®
RAVEN SWATH SMART
Features
Simple LED lights keep you parallel with your last pass,
and on-center, with up to 10 position corrections per second.
Allows you to operate at night - when the wind is down - so you can
expand your hours and cover more acres.
Available as a complete, matched system, or simply add the RGL-500 to
your existing GPS receivers.
Easily adjusted swath width from 5 to 300 feet (1.524 to 91.44 meters),
Plus, standard 10HP update provides a correction signal every 1.8 feet
(.5486 meters) at 12 MPH (19.3116 KPH).
Either system can be easily added to your present applicator units and are
available as an option on Precision’s complete line of new application
equipment. Call or write for additional information and pricing on the
system of your choice!
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
SPRAY CONTROLLERS/MONITORS
Raven SCS 440/450/460 Sprayer Control Systems
Raven SCS 440/450/460 sprayer controllers provide precision
single product automatic rate control with the flexibility of up to 7
boom section inputs. Two separate application rates can be
pre-programmed into the controllers and selected ‘on the go’ with
the flip of a switch. Application rates can be manually overridden
to accommodate spot spraying needs even when in automatic.
The SCS 440/450/460 consoles are GPS compatible for variable
rate application and data logging. All logged data can be
Raven SCS 440 - 3 Section Boom Control
downloaded for use in determining future application information.
User friendly programming, non-volatile memory, easy to read
lighted display and data lock, combined with the reliability,
accuracy and affordability of Raven systems make the SCS
440/450/460 consoles the right choice for single product chemical
application.
Features:
• New, easy-to-read digital display
• Ground speed compensated automatic rate control
• One-time, easy programming
• Simple cabling and installation
• Cumulative TOTAL VOLUME applied and TOTAL AREA worked for
Raven SCS 450 - 6 Section Boom Control
KêKêKêKêKêKêKêKêKêKêKêKêKêKêKêKêKêKêKêKêKêKêKêKêKêKê
record keeping
• On-the-go programmable rate change
• GPS compatible
• 3 to 7 boom control (switch box required with the SCS 460)
• Low limit function to eliminate pattern degradation
• Multiple audible alarms for system monitoring
• Self-test function for system check-out
Raven SCS 460 - 7 Section Boom Control
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
SPRAY CONTROLLERS/MONITORS
Dickey-john DjCMS100
Used as a stand alone unit or in conjunction with one of the DjCCS100 control systems, the
DjCMS100 is a versatile product.
Features:
• Speed Total Area accumulation
• Product Level (amount left in tank or hopper)
• Field Area accumulation
• Low Level Alarm
• Area/Hour
• Application Rate
• Distance Readout (feet)
• Pressure
• Total Product accumulation
• Fan RPM with High/Low alarm settings (granular only)
• Field Product accumulation
Dickey-john DjCCS100 (Liquid & NH3)
The DjCCS100 system is a field proven product designed for liquid pressure based or NH3
control.
Features:
• Controls Liquid & Anhydrous Ammonia
• Change rate on-the-go
• Optional lift switch can be tied into lift cylinder hands free ON/OFF
• Non-Volatile Memory
• Can be used with DjCMS100
Dickey-john DjCCS100 (Granular)
The DjCCS100 granular control system is based on the same field proven design as the
DjCCS100 liquid & NH3 controller.
Features:
• Controls Granular product application
• Works with single or dual drag belt
• Change rate on-the-go
• Non-Volatile Memory
Spray Controllers/Monitors – A variety of manufacturers of spray controllers (dry and
liquid) and monitors are stocked or are available, such as Dickey John, Hiniker, Raven,
Redball, Spraying Systems and others. We have in-stock items from complete kits to the
individual components, such as radar guns, transducers, valves, cables, and flow meters.
Let us help you in determining the system that is best suited for your individual needs.
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
FOAM MARKERS
Foam Marker Systems & Parts
BOOM PARTS
Miscellaneous Boom Parts
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
TIRES & WHEELS
Tires
Wheels
* Many other styles of tires and wheels are available. Call for package
prices.
Mud Flaps
* Call for fiberglass fenders, rubber fenderlips, catwalks and catwalk
brackets.
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
BEARINGS & DRIVE SYSTEMS
PTO Cables & Shafts
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
BEARINGS & DRIVE SYSTEMS
Flange Bearings
Pillow Block Bearings
* Slip shafts and component parts are in stock for your applicator. Please specify length and sizes. Some standard PTO’s are in stock,
others are available overnight.
* Solid keyed shafts are available from our shop in your custom or standard dimensions.
* Other bearings and oil seals are available. PTO parts such as gears, spacers, gaskets, stud kits, ratio adapters and cables are in stock.
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
SPROCKETS & PULLEYS
QD Sure Grip Pulleys
QD Sure Grip Bushings
Timing Belts
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
SPROCKETS & PULLEYS
Taperlock Pulleys
Taperlock Bushings
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
COUPLING, MOTOR/PUMP
Lovejoy
Woods, SC
Paraflex
* Chain drive couplings also available.
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
ELECTRIC MOTORS
Baldor Electric Motors
Motor Base Plates
* Many other motors are available in various horsepower, rpms, frame sizes and types. Electrical conduit, connectors, motor boxes and
baseplates are also available.
* Gasoline engines are available for various applications. Available brands are: Briggs & Stratton, Kohler, Tecumseh and Honda.
Various models include B&S standard or I/C series, Kohler standard or Magnum series in the full model lines. Gear reduction models
are available, as well as engine accessories.
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
MISCELLANEOUS
Miscellaneous Electrical Parts
Air Cleaners
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
MISCELLANEOUS
Jacks
Miscellaneous Equipment & Supplies
* Paint – A large variety of paint and paint supplies are in stock in a
variety of brands.
SAFETY EQUIPMENT & DECALS
Water Containers
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
SAFETY EQUIPMENT & DECALS
Unvented Goggles
Fire Extinguisher
Chest Mask w/Canister
Gloves
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
SAFETY EQUIPMENT & DECALS
Safety Pins
Air Safety Equipment
Pressure Washer
* Pressure wash pumps, reels, hose and nozzles are in stock.
Throttle Lock Cable
Flush Tanks
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
SAFETY EQUIPMENT & DECALS
Safety Rope
Decals
* Other anhydrous ammonia, nitrogen solutions, aqua ammonia, nonflammable gas, liquid, vapor, and many other decals and placards are
available.
Vent Tees & Caps
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
SAFETY EQUIPMENT & DECALS
Safety Lights
Safety Rinse Equipment
Press-On Walk Material
Nozzle Testing Equipment
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814
SAFETY EQUIPMENT & DECALS
Soil Probes
Density Scale
* Slow-Moving Vehicle Signs available in decal and magnetic
* Rain Gear and Rubber Boots available.
material.
* Respirators are available in chin style or full-face cover with a variety
* DMI Bumpers available.
of canisters for various applications.
* First Aid Kits for on-site emergencies are available.
NEW LEADER
Precision Tank & Equipment Co. is your authorized
dealer for New Leader Equipment. We specialize in
parts and service for your L-2020 and L-3020 units
and are happy to assist you with any needs you may
have for any other models. Call or write for com
plete parts manual for the unit of your choice.
Precision Tank & Equipment Co.
1
Parts Hotline: 1-800-811-7814