Automotive Repair Shops

Automotive Repair Shops Case Study
–
ME 4171
Automotive Repair Shops
In the following, you will be given a case study which was performed by a consulting firm
in the late eighties regarding the waste generated by automotive repair shops in California.
A lot of you will have had experience with automotive body repair, or at least know
somebody who had such an experience. You don’t have to go far to find examples of
these shops in your town. In the following, we will take a look at some issues related to
the sustainability of this type of industry.
INDUSTRY PROFILE
DESCRIPTION OF INDUSTRY
The specific companies audited in this study were selected from the
industry classifications which include top and body shops and paint shops.
The establishments in this industry are engaged in general automotive and body
repair with particular focus on collision repair and painting.
These shops
are distributed throughout the state.
The heaviest concentrations are near
urban centers and in industrial areas.
The majority of these establishments are small in size with an average
of 7 employees. Of the 6 audited companies, 1 had less than 5 employees, 3
had between 5 and 10 employees, and 2 had over 10 employees.
In a previous
study conducted by SCS Engineers (1982), automotive paint and body shops were
included as part of a larger small-quantity hazardous waste generator study.
Of the 24 companies representing this industry,
17 had between 1 and 10
employees; the remaining 7 had between 11 and 25 employees.
The automotive paint and body industry can be divided into two distinct
subsets.
The first consists of shops that work only on collision repair,
frame and front-end adjustments, and body painting.
These companies generate
paint-associated hazardous wastes almost entirely.
These wastes include
toxic and ignitable thinners, toxic paint wastes, paint sludges and oil- and
solventcontaminated rags, empty cans with paint and thinner residues, and
contaminated paint booth filters.
The second group of shops do mechanical work as well as collision
repair.
In addition to the above-noted wastes,
these shops produce
hazardous
waste
streams
which
include
waste
oils,
oil
filters,
engine/hydraulic fluids, antifreeze, and corrosive wastes from lead batteries.
Very few automotive paint and body shops conduct mechanical work in
conjunction with collision repair.
WASTE GENERATION
To perform collision repair, body shops use a wide range of equipment,
chemicals, and raw materials.
Available services include welding,
filling
dents with plastics or fiberglass, body section adjustments, alignments, and
painting.
Body repair work cannot be performed without the use of welding
equipment such as blow torches.
This equipment is used extensively in body
shops and has various uses, including welding, cutting, and heating to shrink
and expand metals, to forge or shape metal, and to solder.
A welding and
cutting job requires equipment such as an oxygen cylinder, acetylene cylinder,
welding torch, regulators, and steel filler rods. The flame produced when the
two gases are mixed together is hot enough to melt, bond, and repair most
commercial metals.
Question:
–1 –
Automotive Repair Shops Case Study
–
ME 4171
1) Do you anticipate hazardous wastes generated through welding?
To repair both minor and major auto body damage, hydraulic equipment
and hand tools are used to restore damaged sections, assemblies, and parts to
their original positions and shapes. Equipment such as jacks and lifts
generates enormous pulling and pushing capacities.
These heavy machines can
straighten bent frames, align hoods and fenders, and adjust panels.
Oil is
essential to the proper operation of these machines.
Regular fluid changes
and repair to equipment generate spent fluids, which are recycled with other
waste oil generated on site.
Question:
2) Do you expect the equipment oil and lubricants to be a significant portion of waste
generated?
3) Give an estimate of how much engine oil a car uses during its life span.
4) What is cheaper, to overhaul/recondition a worn car engine which is burning oil or
just add motor oil? What is better for the environment?
5) What is an important motivation for reconditioning worn equipment which leaks
oil?
6) How does this relate to sustainability?
When dented, some areas on an automobile body are not accessible for
repair with the use of hydraulic equipment. These areas can be repaired with
plastic or fiberglass body filling. These are used by adding a hardener or
catalyst to the filler material and layering it in the area of the dent. The
material, which is mixed on a glass or steel plate, is applied to the damaged
area.
To reduce generation of residual waste materials, a conservative
quantity of material is mixed. Once the dent has been completely filled, the
excess dried material is sanded down flush with the rest of the body.
This
process does not generate extra material, because the entire quantity that is
mixed is applied to the dented areas. The major residual waste generated is
fiberglass and plastic dust which collects on the floor during sanding
operations. This material is collected and deposited into refuse dumpsters.
Minor quantities are rinsed into drains during routine washdowns.
Question:
7) What is a big concern in repairing cars with fiberglass filling?
8) If you were told that it was a hazardous process, what would you do to prove or
disprove this statement?
The largest amounts of hazardous waste are generated from service and
painting operations.
Services conducted in conjunction with body repair can
include oil changes, fluid replenishment, and radiator repairs.
These
activities generate hazardous wastes such as waste oil, oil filters, engine
and hydraulic fluids, wastes from radiator flushings, used batteries, and
contaminated rags.
Paint operations generate the largest volume of hazardous wastes for
this industry through the use of chemicals such as paint thinners and
reducers, and the paint itself.
Paint is sprayed under pressure onto
automobile surfaces via a medium of paint thinner.
Once the paint is
applied, the thinner evaporates and the paint dries and hardens.
A
significant portion of the product evaporates during the painting process,
resulting in less waste generated than product used.
This accounts for the
large discrepancy between the amounts of raw material thinner purchased and
the amount of waste thinner generated.
In addition to use as a carrier for
–2 –
Automotive Repair Shops Case Study
–
ME 4171
applied paint, paint thinner is also used as a solvent to clean equipment.
According to a study conducted by TRW (1979), the total amount of
hazardous waste generated by the targeted industry throughout the nation was
estimated to be 1.8 million pounds per month (820,000 kilograms per month),
with an average generation rate of 77 pounds per month (35 kilograms per
month) per generator. This figure, however, also includes wastes generated by
the tire retreading and repair shops. Therefore, the generation rate would be
somewhat lower, because rubber/tire wastes and toxic fluid wastes would not be
included.
Waste thinner generation rates from data collected by SCS Engineers
(1982) range between 0.8 and 200 gallons per month. Monthly waste generation
rates for the audited companies, shown in Table 4-1, range between 5 and 37
gallons per month.
TABLE 4-1.
MONTHLY HAZARDOUS WASTE GENERATION FOR AUDITED COMPANIES
Company
No.
Employed
Business
Volume
(No. Cars)
Thinnet/
Paint
Sludge
(gal)*
A
B
C
D
E
F
6
13
13
9
7
3
50-75
100
55
30-40
30
25
5
37
20
30
17
5
Empty
Trans.
Hydraulic
Paint Cans Fluid (gal) Fluid (gal)
5-7
5-10
20-30
25-35
25-30
25
0
0
2
0
0
0
0
0
2
0
0
0
AntiFreeze
(gal)
Oil (gal)
0
0
8
0
1-2
0
6
0
7
0
14
0
* Thinner/paint sludge also includes additives of hardeners, catalysts,
and reducers.
Question:
9) If the data in table 4-1 would have been reported by the companies, which
company would you send an audit team to check their data?
10) Based on the data given in the table, create a graph and estimate the amount of
waste generated by a company that has a business volume of 145 cars.
11) How can you account for the discrepancies in number of paint cans between
company B and companies C, D, E, and F.
WASTE RECYCLING
Excess paint, paint sludge, and thinner mixtures are poured into 55gallon drums or other containers for storage.
The paint sludges and solids
settle to the bottom,
leaving a liquid layer of thinners on the top.
The
waste drum is subsequently removed by a hauler to a reclamation or disposal
facility.
With the exception of one company which reclaims wastes on site, all of
the audited companies utilize the services of a reclamation facility for the
removal of wastes.
This service is part of a turnkey operation provided by
the paint and thinner supplier.
The purchase of chemicals includes the cost
of delivery, waste hauling, recycling, and disposal. The service removes the
wastes at the same time that it delivers the new product.
The service will
remove the supernatant from the waste drum using a pump truck (with sludge
removed on a less frequent basis), or will haul the entire drum away.
The
–3 –
Automotive Repair Shops Case Study
–
ME 4171
waste is hauled to a licensed treatment, storage, and disposal (TSD) facility
for reclamation.
The service collects from a number of small-quantity
hazardous waste generators in a given area.
This renders reclamation
economically feasible for this industrial segment.
The one company that did not use an off-site treatment service had
recently installed on-site recycling equipment for thinnet and paint wastes.
Question:
12) Why would the service of a reclamation facility be advantageous for most
companies?
13) Can you name some reasons as to why one company would choose to install an
on-site recycling equipment?
14) Would you recommend installation of recycling equipment for all companies?
15) Given a 90% recycling efficiency, estimate the residual waste generated by these 6
companies over 10 years? Focus on paint / thinner sludge only.
Other studies suggest that the use of recycling in this industry has
not been typical in the past. In a study conducted by SCS Engineers (1982) in
which all companies in a limited area were contacted, most companies in the
automotive paint and body industry were disposing of wastes with conventional
refuse, pouring wastes on soil, or allowing wastes to evaporate.
Three of
the 24 companies surveyed were recycling wastes.
However, this practice was
limited to waste oils.
Question:
16) Can you suggest reasons for this discrepancy between the two studies regarding
recycling?
WASTE STORAGE
The industry uses basically two methods of chemical and hazardous waste
storage.
In some shops, all of the thinners, new chemicals, and wastes are
stored together in a designated covered area.
The drums are placed on
asphalt, concrete, or steel floors.
The remaining shops store their drums
indoors, but scatter them around the shop at the points of highest use.
In some studies, improper storage and soil contamination have been
noted as being indigenous to the automotive painting and body repair business
(SCS Engineers, 1982).
No evidence of drum storage outdoors or on open soil
was observed during the audits.
This greatly reduces the potential for
accidental or intended soil contamination.
While none of the shops visited
used drum cradles or stands, all of the companies used some type of spigot or
pump as well as lids to reduce product spillage and evaporation.
All
companies participating in the hazardous waste audit had an average of between
two and seven drums containing chemicals and/or hazardous wastes on site.
Although most of the contacts interviewed expressed a willingness to
operate within industry regulations set by the state, hazardous waste storage
ceilings were often ignored or unknown. Most of the smaller operators use
waste inventory as a means of determining when to call their recycler. In the
smaller shops, however,
it often takes up to 6 months to fill a 55-gallon
drum with waste thinners and paints.
Although a 90-day limit for storage of hazardous wastes is imposed
under current hazardous waste regulations,
the time period for calculating
the 90-day limit for generators of less than 100 kilograms per month begins
when 100 kilograms of hazardous waste are accumulated.
If more than 100
kilograms are generated in any calendar month, the time period begins when any
–4 –
Automotive Repair Shops Case Study
–
ME 4171
amount of waste begins to accumulate.
With the exception of one shop, all
audited operations generated less than 100 kilograms of hazardous waste per
month.
Waste storage for up to or beyond 90 days must meet federal, state,
and sometimes local regulations.
Question:
17) Name a situation where storage for more than 90 days may be necessary.
WASTE DISPOSAL
Several studies have cited prevalent disposal practices within the
industry.
These include waste thinners being discharged into the sewer or
disposed of on open ground, and paint cans and filters being disposed of in
on-site solid waste dumpsters (SCS Engineers, 1982).
During the course of
our audits, there was no evidence of large-quantity thinner discharges into
the sewer or onto open ground.
One shop owner admitted to pouring waste oil
along one side of his facility as a means of weed control; however, he
discontinued this practice some years ago when the DHS warned him of the
associated hazards.
Question:
18) What are some of the associated hazards associated with using thinner as weed
killer?
During the interviews the largest potential for waste disposal
mismanagement was found in the handling of paint cans with associated
residues, paint equipment filters, oil filters, and small amounts of engine
fluids.
Almost without exception, the cans and filters were disposed of in
on-site refuse dumpsters, to be removed during weekly municipal waste
collections.
When small amounts of engine fluid were generated, they were
allowed to drain onto the floor.
These include anti-freeze from damaged
radiators, brake fluids, transmission fluids, etc.
The residues were then
either absorbed with a type of floor drying agent which was subsequently
disposed of in the dumpster, or rinsed down drains or sewers without prior
treatment during routine washdowns.
Due predominantly to economic reasons and ease of operation, none of
the establishments visited used landfills for disposal of waste paint,
thinner, and reducer.
All of the audited facilities utilized waste
recycling, as discussed earlier.
Question:
19) What are some economic reasons for not using a landfill for disposing paint,
thinner and reducer?
20) Can you name some other reasons?
21) Would burning the thinner and oil for, say, shop heating be a good idea?
WASTE MANAGEMENT
In a previous study done by SCS Engineers (1982) as part of a small-quantity
hazardous waste generator study, data were gathered from the auto body
industry to determine the amount of money that individual companies would
budget for hazardous waste management.
At the time of the 1982 study, no
company was spending in excess of 0 to 5 percent of its budget on hazardous
waste management.
Although most expressed the desire to avoid penalties
associated with hazardous waste storage and removal,
few were willing to
absorb the extra costs involved.
Our interviews showed that most operators
thought the laws governing their industry to be confusing and ambiguous.
It
–5 –
Automotive Repair Shops Case Study
–
ME 4171
was the consensus of the operators that regulatory language needs to be
simplified, and that industry updates should be distributed on an annual
basis.
Questions:
22) What would it take to distribute updates on an annual basis?
23) Can you give suggestions to simplify the language?
CLOSING QUESTIONS:
24) In the preceding text, which major waste stream was more or less neglected?
25) What are some incentives for waste reduction?
26) What are categories and options for waste reduction?
27) Consider the situation in Atlanta. Make an assessment of the amount of waste
generated until the year 2000 by automotive repair shops in the Atlanta area.
First, try to perform such an assessment without making any phone calls. Next,
try to verify your findings.
28) As a “sustainable solution”, would it be feasible to group repair shops together in
“Car Health Maintenance Organizations” analogous to medical HMOs?
–6 –
Automotive Repair Shops Case Study
–
ME 4171
Appendix A
Synopsis of the Small Quantity Generators Regulations
Facilities producing between 220 and 2200 pounds (100 and 1000
kilograms) of hazardous wastes per month are subject to the Small Quantity
Generator regulations.
These regulations will require waste producing
facility to:
1)
Identify the hazardous wastes produced.
2)
Obtain an EPA identification number.
3)
Ship hazardous wastes for treatment, storage, or disposal in EPA
approved facilities.
The shipment will have to meet the requirements
set by the Federal Department of Transportation for hazardous wastes.
In addition the shipment will have to be accompanied by a manifest
containing the generator's name and
address, the shippers name, and
the name and address of the receiving facility.
4)
The hazardous wastes should be offered, at least every 180 days, to
shippers and disposal facilities with an EPA identification number. In
Alaska, because there are no EPA certified hazardous waste disposal
sites within 200 miles, the wastes can be stored for 270 days. The
maximum weight of the wastes being stored, however, cannot exceed
13,200 pounds.
5)
Finally, the waste generator
manifest for three years.
should
–7 –
keep
a
copy
of
the
shipping
Automotive Repair Shops Case Study
–
ME 4171
APPENDIX B – LIABILITY ISSUES
The following text highlights liability issues, regulations, and two actual cases. It provides
a quick summary and introduction to the legislation involved. It is taken from “Managing
and Recycling Solvents – North Carolina Practices, Facilities, and Regulations”, by
Jerome Kohl, Phillip Moses, and Brooke Triplett, Industrial Extension Service, School of
Engineering, North Carolina State University, Raleigh, North Carolina, December 1984.
Liability
1. Superfund
The Superfund law of December 1980 - CERCLA - authorizes the Federal
Government (through the EPA) to respond directly to releases (or threatened
releases) of hazardous substances and pollutants or contaminants that may
endanger public health or welfare.
Costs are to be covered by a more than
$7.6 billion fund, 86% of which is financed by taxes on the manufacture or
import of certain chemicals and petroleum, the remainder coming from general
revenues (as of October 1, 1984, this act is up for extension with the
provision of additional funds).
This fund is reimbursable:
the EPA takes
legal action to recover its cleanup costs from those subsequently identified
as responsible for the release. Anyone liable for a release who fails to take
ordered action is (under specified conditions) liable for punitive damages
equal to 3 times the government's response costs.
EPA's enforcement effort seeks to ensure that responsible, private
parties finance cleanup actions when possible. Direct government action, when
called for, can take the following forms:
-
Immediate removals, when a prompt response is needed to prevent harm to
public health, welfare or the environment.
-
Planned removals, when an expedited, but not necessarily immediate,
response is needed to minimize increases in danger or exposure that
would otherwise occur, if response were delayed.
-
Remedial actions, which are longer-term and usually more expensive,
aimed at permanent remedies.
Remedial actions may be taken only at
sites which are indicated on EPA's National Priorities List.
Sites on the National Priorities List were ranked by the MITRE
Corporation. The ranking is based on 3 things: the toxicity of the substance
involved, the closeness of the site to humans, and the possible pathways of
the substance into the environment (such as soil, water and air). The present
list ranks over 400 sites nationwide.
2. Summary of Generator Liability
a.
RCRA
Under RCRA's "cradle to grave" philosophy a generator is never relieved of
responsibility for his hazardous waste. If a treater, storer, disposer (TSD),
or transporter spills hazardous wastes, or if hazardous wastes are released
into the environment (leaks, leaching, etc.) then the generator can be held
liable for any damages and cleanup costs that the TSD or transporter cannot
pay. The generator does not have to be proven negligent in order to be held
liable for his hazardous wastes. This is called Strict Liability "liability
without fault".
b. Joint and Several Liability Under Superfund
–8 –
Automotive Repair Shops Case Study
–
ME 4171
If hazardous wastes are released into the environment from a TSD site then
all the generators who have used that site are "jointly and severally" liable
for the cleanup costs and resultant damages that the TSD facility cannot pay.
This means that if a generator has contributed only a small amount of wastes
to a facility where a cleanup is needed, that generator can be forced to pay
for a much larger part of the mess than his particular wastes were responsible
for.
In some cases, he can be held responsible for all of the mess.
Thus,
even if ~ generator sends only a small amount of hazardous wastes off-site, he
must be very prudent in choosing a TSD facility since the generator may be
held liable for the TSD's mistakes. Presently, legal courts are moving toward
applying "apportionment" procedures to this problem but for now, the above
holds true.
3. Multiple Generator Sites
At Superfund sites where multiple generators have been named by the EPA
as having contributed hazardous wastes to the site (potentially responsible
parties), the agency has so far pursued the following line of action.
a.
If the owner/operator of the facility does not agree to clean up the
site, or if immediate removal of wastes is required and there is no
time to identify the responsible parties, the EPA cleans up the site.
After the cleanup is completed, the EPA sues the owners, operators and
generators for cleanup, administration and court costs.
b.
The EPA can order the owners or operators of a facility to perform an
immediate removal of hazardous substances because of imminent danger to
public health, welfare or the environment.
If the facility fails to
clean itself up without "good cause" as an excuse, then the EPA removes
the hazardous substances and sues the responsible parties (which may
include the generators as well as the owner/operator of the facility)
for punitive damages equal to three times the cost of EPA's response.
Examples of EPA cleanups under Superfund in the southeast and cost recovery
from generators are:
Lenoir Refining
Lenoir Refining Company was located in Lenoir, North Carolina. The facility
occupied three acres of land and consisted of a small office, a warehouse, a
drum storage area and a third building housing solvent distillation equipment.
Lenoir Refining Company would pick up spent solvent from local furniture
manufacturers to be distilled and returned to the manufacturers.
The spent
solvent backlog and still bottoms were drummed and stored in an outdoor
uncovered area.
Over the years, a backlog of an estimated 750-1000 drums accumulated on the
site. Many of the drums were uncovered or deteriorating and leaking. Few had
labels "identifying contents and fumes from the drums were detectable within
several yards of the site.
The risk of fire, explosion, flooding, and the
lack of site security were the major hazards posed by the site.
The
population within a 1/2-mile radius of the site is approximately 12,000.
The
site is located on a flood plain.
On several occasions, it has been flooded,
threatening to wash the drums of solvent and contamination from the soil into
a nearby creek and eventually into the Catawba River which is used for
recreational purposes and as a drinking water supply for many communities.
Despite its hazards, the site was freely accessible to the public with no
fence, no warning signs posted and no natural barriers inhibiting access to
the site. The organic solvents present on-site were acetone, benzene, ethyl
benzene, methyl ethyl ketone, toluene and isopropyl acetate.
On October 14, 1982, the EPA began a planned removal action at the Lenoir
Refining Company site.
A total of 1,301 drums and 160 cubic yards of
contaminated soil were removed from the site at a cost of $92,189.54. The EPA
–9 –
Automotive Repair Shops Case Study
–
ME 4171
can charge up to three times the cost of cleanup.
After the cleanup was completed, the EPA recovered a total of $113,000.00
from the seven responsible parties:
Lenoir Refining Company, Broyhill
Manufacturing Company, C.T.S. of Asheville, Ethan Allen, Inc., Lackawanna
Leather Company, Southern Cabinet Company, Inc., and Sperry and Hutchinson
Furniture, Inc.
Bluff Roads
The "Bluff Roads" site is near Columbia, South Carolina. The site covers
approximately four acres and is within 1/2 mile of a large plant employing
more than 800 people around the clock.
The topsoil at the Bluff Road site is sandy and quite permeable. The water
table is only five feet below the surface.
The area is characterized by
marshland, creeks and waterways contiguous with the site.
From 1974 until 1980, Columbia Organic Chemical Company operated a solvent
and industrial waste recycling facility at Bluff Road. In 1980, South Carolina
Recycling and Disposal, Inc. (which had also been operating a recycling
facility on the site since 1976) took over the site completely and Columbia
Organic Chemical Company removed its chemicals and moved off the site.
Before the EPA started cleaning up, approximately 7500 drums of
volatile organic chemical wastes and other hazardous substances were on the
site. Some drums were leaking or uncovered emitting toxic fumes and causing
spillage and soil contamination. A large number of drums were stacked tightly
together, as many as three high, and few had pallets to protect them from the
ground.
Solvents stored at the site included xylene, toluene, ethyl ether,
isopropyl alcohol, acetone, methyl acetate, benzene, trichloroethylene, carbon
tetrachloride, and perchloroethylene.
In October, 1977, heavy rainfall caused a chemical reaction with wastes
stored in decomposing drums forming a cloud of toxic gases. Fifty people were
hospitalized for exposure to these gases. Two fires have broken out at the
site; one in 1979 and one in 1982.
In 1982, the EPA charged the owners of the site and a group of
companies as being liable for the cost of the site cleanup which the EPA
estimated at $1,6000,000.
RAD Services, a hazardous waste transporter, and twelve other unnamed
companies agreed to pay for 75% of the surface cleanup (the fraction of
problem wastes attributed to private industry). Seventy-five percent of EPA's
cost estimate is $1,200,000, but since RTI performed the cleanup for the
companies, the exact cost was not disclosed.
The EPA, then funded by the responsible governmental agencies,
completed the rest of the surface cleanup. The Eaton Corporation also agreed
to pay the EPA $95,000.00 for surface cleanup costs.
According to the resulting agreements, if a groundwater cleanup is
found to be necessary, the EPA will try to recover the cleanup cost from the
other companies named in the suit before trying to recover costs from Eaton,
RAD or the twelve unnamed companies.
This case has not yet been closed, so no figures have been published.
However, if past groundwater cleanups are any indication of what the Bluff
Roads site would require, one could guess that, if the court rules in favor of
EPA, Monsanto, Allied and EM Corporation could be forced to pay substantially
more than have Eaton, RAD and the twelve unnamed companies.
– 10 –