SAN213 Instruction Manual

SAN213 Instruction Manual
Scan here to view
product demo and install
videos or visit san.us/105
Milestone AV Technologies
6436 City West Parkway
Eden Prairie, MN 55344 USA
Customer Service
Americas: 800-359-5520 • 651-484-7988 • [email protected]
Europe, Middle East, and Africa: +31 (0) 495 580 852 • [email protected]
Asia Pacific: 86 755 8996 9226 • [email protected]
accents.sanus.com
©2012 Milestone AV Technologies, a Duchossois Group Company.
All rights reserved. Accents is a Milestone brand.
All other brand names or marks are used for identification purposes and are trademarks of their respective owners.
(6904-002011<02>)
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE
Specifications
Ù Weight capacity-DO NOT EXCEED: 20.5 kg (45 lb) includes TV and any accessories
Ù Tilt: ± 15°
CAUTION: Avoid potential personal injuries and property damage!
Ù
Ù
Ù
Ù
Do not use this product for any purpose not explicitly specified by manufacturer.
The wall must be capable of supporting five times the weight of the monitor and mount combined.
This product is not designed for use in metal stud walls!
If you do not understand these instructions, or have doubts about the safety of the installation, assembly or use of this
product, contact manufacturer Customer Service or call a qualified contractor.
Ù Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.
Technical Specifications
200 mm
7.87 in.
100 mm
3.94 in.
75 mm
2.95 in.
75 mm 100 mm
2.95 in. 3.94 in.
169.3 mm
6.67 in.
59.2 mm
2.33 in.
180°
360º
256.1 mm
10.08 in.
318.3 mm
12.53 in.
230 mm
9.06 in.
64.3 mm
2.53 in.
15°
143.5 mm
5.65 in.
241 mm
9.49 in.
15°
2
6904-002011<02>
Required Tools
13mm
(1/2 in.)
5.5mm
(7/32 in.)
10mm
(3/8 in.)
Supplied Parts and Hardware
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the
damaged item to your dealer; contact Customer Service. Never use damaged parts!
NOTE: M4 describes the diameter, mm describes the length of screws that are labeled M# X ##mm. Not all hardware included
will be used.
[01] x 1
[02] x 1
5/16 x 2 ½ in.
1/4-20 x 3 ¼ in.
[03] x 2
[04] x 2
[06] x 1
M4 x 12mm
[11] x 4
M4 x 30mm
[12] x 4
[07] x 1
[05] x 1
1/4-20 in.
0.5 in.
0.5 in.
[08] x 1
[09] x 1
[10] x 2
M4
[13] x 4
8-32 x 1/2 in.
[14] x 2
[15] x 4
[16] x 4
5/32 in.
[17] x 4
6904-002011<02>
[18] x 1
3
1 Attach TV Bracket
For TVs with a flat/unobstructed back
Ensure that the bracket is level on the back of the TV. Standard configurations are shown. If you need extra space to accommodate cables, recesses, or
protrusions, see the installation option that uses spacers. For special applications, or if you are uncertain about your hardware selection, contact Customer
Service.
[02]
[11]
1 Attach TV Bracket
For TVs with an irregular/obstructed back
Ensure that the bracket is level on the back of the TV. Standard configurations are shown. For special applications, or if you are uncertain about your hardware
selection, contact Customer Service.
[02]
[12]
[13]
4
6904-002011<02>
2 Mount the Wall Plate
13 mm
(1/2 in.)
Wood Stud
1.
2.
Locate stud. Verify the center of the stud with an awl or
thin nail or use an edge to edge stud finder.
CAUTION: To avoid potential injuries or property
damage:
Ù Any material covering the wall must not exceed 16
mm (5/8 in.).
Ù Minimum wood stud size: common 2 x 4 in. (nominal
1.5 x 3.5 in.)
Level the wall plate [01] and mark the hole locations.
3.
Drill pilot holes as illustrated.
CAUTION: To avoid potential injuries or property
damage: Pilot holes MUST be drilled to a depth of 63.5
mm (2½ in.), using a 5.5 mm (7/32 in.) diameter drill bit.
1
4.
5.5 mm
(7/32 in.)
Tighten the lag bolts [03] only until they are pulled
firmly against the wall plate [01].
CAUTION: Improper use could reduce the
holding power of the lag bolt. To avoid potential
injuries or property damage: DO NOT over-tighten
the lag bolts [03].
5.
Place lag bolt covers [16] over lag bolts [03].
2
[01]
< 16 mm
(5/8 in.)
4
3
[01]
63.5 mm
2½ in.
[03]
5
[16]
6904-002011<02>
5
2 Mount the Wall Plate
13mm
(1/2 in.)
Solid Concrete and Concrete Block
1.
Level wall plate and mark the hole locations.
3.
Insert lag bolt anchors [04]. Be sure the anchors [04] are
seated flush with the concrete surface.
4.
Tighten the lag bolts [03] only until they are pulled firmly
against the wall plate [01].
CAUTION: To avoid potential injuries or property
damage:
Ù Mount wall plate directly onto the concrete
surface.
CAUTION: Improper use could reduce the holding
power of the lag bolt. To avoid potential injuries or
property damage: DO NOT over-tighten the lag bolts
[03].
Ù Minimum solid concrete thickness: 8 in.
Ù Minimum concrete block size: 8 x 8 x 16 in.
2.
10mm
(3/8 in.)
Drill pilot holes as illustrated.
5.
CAUTION: To avoid potential injuries or property
Place lag bolt covers [16] over lag bolts [03].
damage:
Ù Pilot holes MUST be drilled to a depth of 75 mm
(3 in.), using a 10 mm (3/8 in.) diameter drill bit.
Ù Never drill into the mortar between blocks.
1
2
[01]
75 mm
3 in.
3
4
[04]
[01]
[03]
5
[04]
[16]
6
6904-002011<02>
3 Attach the TV Bracket onto the Swing Arm/Wall Plate
1.
2.
3.
4.
Fit nut [08] and cover [16] into underside of mount arm
[01].
Place washer [07] and pivot pin [06] onto mount arm.
Heavy: You will need assistance with this step! Fit
mounting bracket [02] onto pivot pin [06]. Slide washers
[10] and spacer [09] onto mounting bolt [05] and fit bolt
through mounting bracket [02] and pivot pin [06] until it
meets nut [08].
Use hex key [18] to tighten mounting bolt [05] and secure
mounting bracket [02] to arm [01].
4
[18]
[02]
[01]
[16]
3
[05]
[10]
[09]
[10]
[02]
1
2
[06]
[01]
[07]
[08]
[01]
[16]
6904-002011<02>
7
4 Manage Cables
Pull the arm to its full extension before routing the cables through the channels, then loosely route the cables. This will give the cables enough slack to
prevent excess tension when adjusting the position of the arm.
[01]
[14]
[15]
[15]
[14]
[15]
[15]
[01]
[14]
[17]
[17]
[17]
[14]
[17]
8
6904-002011<02>
5 Adjust Tension
A: Adjust arm extend / retract tension
B: Adjust left / right swivel tension
C: Adjust up / down tilt tension
SIDE VIEW
TOP VIEW
A
[18]
B
[18]
SIDE VIEW
C
6904-002011<02>
9
Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively, “Milestone”), intend to make this manual accurate and complete.
However, Milestone makes no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible
contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or
obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
10
6904-002011<02>