PLUSH BACKWASH

Assembly Instructions
Plush Backwash
PLUSH BACKWASH
4001204
R
Tools & hardware
1
Hanger bolt or other fastener suitable for floor
construction - obtain locally. 4 required.
2
Lead anchor or other fastener suitable for
masonry floor construction - obtain locally.
NOTE: Because we cannot anticipate all types of floor constructions, the fasteners required to hold this
unit in place MUST be obtained locally. Each unit requires four (4) fasteners.
Different floor constructions will require different fasteners. If you are not certain which type of fastener to
use, consult with your contractor.
IMPORTANT! You MUST fasten this unit to the floor. The plumbing connections alone WILL NOT hold
the unit in place.
IT IS THE RESPONSIBILITY OF THE INSTALLER AND/OR THE OWNER TO MAKE CERTAIN THAT THE
INSTALLATION CONFORMS TO ALL PREVAILING LOCAL AND STATE CODES.
3
Power drill - cordless recommended.
4
Drill to fit locally obtained fastener.
5
3/8”- or 1/2”-drive ratchet wrench.
6
7/16” socket.
7
1/2” extra-deep socket.
Ratchet wrench extensions.
8
Produced by: J. Baer
Date: 02/09
Amended:
Version: 1
Backwash System
Plush
2
For more information on the full line of Belvedere salon furnishings visit www.belvedere.com
4001204
Suggested floor layouts
2'-0"
3'-6"
3'-8"
4'-0"
IMPORTANT! AISLE SPACINGS
SHOWN MUST BE MAINTAINED!
NOT TO SCALE
REFER TO MARKED DIMENSIONS
9"
5'-0"
3'-0"
9"
3'-0"
3'-0"
4'-0"
9"
3'-0"
2'-0"
Produced by: J. Baer
Date: 02/09
Amended:
Version: 1
Backwash System
Plush
3
For more information on the full line of Belvedere salon furnishings visit www.belvedere.com
4001204
Plush Backwash Dimensions
IMPORTANT: When designing the floor plan for the salon, be sure to locate
the plumbing stubs from the floor in the 12” x 12” area as shown below.
24”
12”
14”
125/32”
39/16”
FLOOR
FASTENER
LOCATION
2”
22”
2”
16”
FLOOR
FASTENER
LOCATION
12” X 12” AREA FOR
PLUMBING STUBS
30-1/2”
50”
5”
30-1/2”
37-3/4”
275/8”
18”
12”
Produced by: J. Baer
91/4”
Date: 02/09
Amended:
Version: 1
12”
Backwash System
91/4”
Plush
4
For more information on the full line of Belvedere salon furnishings visit www.belvedere.com
4001204
Suggested plumbing layout.
IMPORTANT NOTES:
IT IS THE RESPONSIBILITY OF THE PURCHASER OR THE INSTALLER TO CHECK LOCAL PLUMBING CODES
REGARDING HORIZONTAL DRAINS AND VENTING. LOCAL CODES MAY PROHIBIT GANGING UNITS.
Please read through these instructions before beginning work to familiarize yourself with the various components.
You may need to work with a helper to install this unit.
SUGGESTED LAYOUT FOR LOOP VENT
CHECK LOCAL CODES
FOR THIS DIMENSION
BOWL
LOOP
VENT
CABINET FOR
LOOP VENT
(BELVEDERE
SPECIAL OR
SUPPLIED BY
CONTRACTOR
VENT
PIPE
11/2“
INSIDE DIA.
CLEAN
OUT
DRAIN
TRAP ARM
FLOOR
FLOOR
PITCH
DOWN
PITCH
UP
OPENING IN
FLOOR FOR
DRAIN, HOT
AND COLD
SUPPLY LINES
L
TRAP
Table 7-1
Trap Arm Dia.
Produced by: J. Baer
Date: 02/09
Amended:
Version: 1
Trap Arm Length
11/2“
31/2’
2“
5’
3“
6’
Backwash System
Plush
5
For more information on the full line of Belvedere salon furnishings visit www.belvedere.com
4001204
Suggested plumbing layout.
9”
Wall
32”
CL
CL
Vent
HOT AND COLD
SHUT-OFFS PER
LOCAL CODES
Floor
Supply
Lines
L
L*
*See Table 7-1 and Local Codes
Table 7-1
Trap Arm Dia.
Trap Arm Length
11/2“
31/2’
2“
5’
3“
6’
Produced by: J. Baer
Date: 02/09
Amended:
Version: 1
Backwash System
Plush
6
For more information on the full line of Belvedere salon furnishings visit www.belvedere.com
4001204
Installation
INSTALL THE CHAIR
1. Determine the location for your
Plush Backwash units. See your
floor plan.
24”
12”
14”
2. Measure and mark fastener hole
locations on floor. Use the plan
below. Measure carefully.
125/32”
39/16”
FLOOR
FASTENER
LOCATION
2”
22”
2”
12” X 12” AREA FOR
PLUMBING STUBS
16”
FLOOR
FASTENER
LOCATION
3. Using an appropriate-size bit, drill
four (4) holes for your fasteners. See
NOTE about fasteners on Page 2
ANCHOR (4)
4. If using anchors or similar fasteners,
insert the anchors into the holes in
the floor.
Plumbing
stubs
Produced by: J. Baer
Date: 02/09
Amended:
Version: 1
Backwash System
Plush
7
For more information on the full line of Belvedere salon furnishings visit www.belvedere.com
4001204
Installation
INSTALL THE CHAIR (cont.)
5. Lift the seat cushion assembly out of
the chair. The cushion is fitted with
two metal channels under the front
edge of the cushion. These rest on
metal bars on the frame. No screws
or other fasteners are used.
LEFT SEAT CUSHION
ASSEMBLY OUT OF CHAIR
6. Set the unit in place. Lift it over the
plumbing stubs and align the four (4)
holes in the bottom of the metal
frame with the four holes/anchors (if
used) in the floor. Be careful to avoid
bumping or damaging the plumbing
stubs in the floor.
7. Fasten the unit to the floor with your
fasteners. (See NOTE on Page 2.)
CAUTION: Plumbing alone will NOT
hold the unit in place.
FASTENER (4)
(OBTAIN LOCALLY)
PLUMBING STUBS
Produced by: J. Baer
Date: 02/09
Amended:
Version: 1
Backwash System
Plush
8
For more information on the full line of Belvedere salon furnishings visit www.belvedere.com
4001204
IMPORTANT NOTES:
Bowl Assembly
Read through these instructions before beginning work to familiarize yourself with the various components. Install
the hose receiver and drain in the bowl before attaching the bowl to the metal base. You may need to work with a
helper to install these units.
Any conformance with LOCAL CODES or INSPECTIONS is the RESPONSIBILITY OF THE PURCHASER.
4. Apply a liberal amount
1. Install the hose receiver. To make the hose receiver
of plumber's putty
installation easier, complete these steps to cut screw
(available at most
threads in the hose receiver mounting holes:
hardware stores)
around the top
S Take a mounting screw and drive it 2 or 3 turns
of the drain
into one hole. DO NOT OVERTIGHTEN.
opening.
S Remove the screw.
S
Repeat for all four (4) mounting holes.
PLUMBER’S
PUTTY
2. Place the hose receiver gasket on the bottom of the
hose receiver. Place the hose receiver onto the bowl.
3. Fasten the hose receiver to the bowl with four screws
and the bracket. Be sure the embossed corners of the
bracket are against the underside of the bowl (facing
up).
5. Place the strainer
body in the
opening, and
press it into the
plumber's putty.
HOSE
RECEIVER
PLUMBER’S
PUTTY
DRIVE
SCREW
IN 2 OR 3
TURNS
SCREW
STRAINER
BODY
HOSE RECEIVER
GASKET
6. From the underside of the bowl, place the fibre
washer over the strainer body. Secure the strainer
body with the nut.
DO NOT OVERTIGHTEN.
When the
strainer body
STRAINER
is tightened
BODY
securely, clean
FIBER
off any excess
WASHER
plumber's putty.
DRAIN
NUT
BOWL
7.
EMBOSSED
CORNERS
UP
BRACKET
Attach the
gasket and
tailpiece/drain
hose assembly
to the strainer
body.
DO NOT
OVERTIGHTEN.
GASKET
MOUNTING
SCREW
Produced by: J. Baer
Date: 02/09
Amended:
Version: 1
Backwash System
Plush
9
For more information on the full line of Belvedere salon furnishings visit www.belvedere.com
4001204
Installation
8. Assemble the bowl, bellows and tilt-bracket
assembly. Place the bowl upside-down on a
padded surface
9. Stretch the bellows over the tilt bracket assembly.
ACCESS
HOLES (4)
10. Align the tilt bracket assembly and bellows with
four mounting holes on the bottom of the bowl.
The springs should be facing up and oriented
toward the front of the bowl.
TILT-BRACKET
ASSEMBLY
SPRINGS
TOWARD
FRONT
OF BOWL
11. Fasten the tilt bracket and bellows to the bowl
with four hex head bolts provided. A 1/4”- drive
or 3/8”- drive ratchet wrench with an extension
and 7/16” socket will make this easeir. Note that
there are four large access holes in the spring side
of the bracket assembly. Start all four bolts into
the threaded holes in the bowl, then tighten
them.
BELLOWS
BOWL
INSTALL THE BOWL
12. Lift the bowl assembly over the bowl shroud and
place the drain hose through the hole in the
shroud.
13. Align the mounting studs and spring units on the
tilt mechanism with their corresonding holes in
the shroud and lower trhe bowl onto the
shroud.
14. Fasten the bowl to the shroud with two (2)
bolts and washers and two (2) hex nuts
and washers. You will need your socket
wrench extensions to reach the bolts
and nuts.
Produced by: J. Baer
Date: 12/07
02/09
BOWL
SPRING
UNITS
Amended:
Version: 1
Backwash System
Plush
Pearl
10
For more information on the full line of Belvedere salon furnishings visit www.belvedere.com
4001204
Installation
INSTALL THE FIXTURE
HANDLE
1. Remove the blue and red button from the front of the
handle.
BUTTON
2. Using a small, flat-blade screwdriver, loosen the
set-screw in the handle and lift the handle off of the
fixture.
3. Unscrew the escutcheon from the fixture body.
4. Apply a bead of silicone sealer around the fixture hole
in the bowl.
5. Place the fixture body on the underside of the fixture
hole.
ESCUTCHEON
APPLY
SILICONE
SEALER
HERE
6. From the top side of the bowl, screw the escutcheon
onto the fixture.
FIXTURE
BODY
7. Place the handle onto the fixture. Tighten the set
screw located in the hole for the button.
8. Replace the button with the red side to the left, blue
side to the right.
SPRAY
HOSE
9. If using a 603 Backflow Preventer, screw it onto the
outlet of the fixture. Seal threads with Teflon tape.
BACKFLOW
PREVENTER
10. Place the connector end of the spray hose through
opening in the hose receiver and screw it onto the
fixture outlet (or Backflow Preventer).
SPRAY HOSE
CONNECTOR
11. Connect the hot and cold supply lines and flexible
drain to stubs.
12. Turn on water and check for leaks.
13. Replace seat cushion assembly
IMPORTANT! Code-approved flexible reinforced
connector hoses or pipes MUST be used to connect
the fixture to the hot and cold supply stubs.
IMPORTANT!
It is the responsibility
of the plumber/installer
and the owner to make
certain that the installation
meets and conforms to all
prevailing local codes.
Produced by: J. Baer
Date: 02/09
Amended:
Version: 1
Backwash System
Plush
11
For more information on the full line of Belvedere salon furnishings visit www.belvedere.com
4001204