docLOCATING PIN RETAINER - The NAAMS Global Standard
download 
Report Transcription
LOCATING PIN RETAINER - The NAAMS Global Standard
LOCATING PINS AND RETAINERS COMPONENTS INDEX Assembly 04/30/15 PAGE DATE I-1 02/12/14 Locating Pins and Retainers Components Index I-1.1 02/12/14 Locating Pins and Retainers Components Index I-1.2 02/12/14 Locating Pins and Retainers Components Index I-2 06/23/04 Typical Locating Pin Retainer Assembly I-3 01/17/06 Typical Locating Pin Retainer Assembly I-4 02/12/14 APR010M–APR013M Locating Pin Retainers (Full Metric) I-5 02/12/14 APR020M–APR021M Locating Pin Retainers (Full Metric) I-6 02/12/14 APR030M–APR033M Locating Pin Retainers (Full Metric) I-7 02/12/14 APR040M–APR041M Locating Pin Retainers (Full Metric) I-8 02/12/14 APR050M–APR051M Locating Pin Retainers (Full Metric) I-9 02/12/14 APR060M–APR063M Locating Pin Retainers (Full Metric) I-10 02/12/14 APR070M–APR071M Locating Pin Retainers (Full Metric) I-11 04/30/15 APS061M–APS199M Locating Pin, 6 mm Thru 19 mm Dia. (Full Metric) I-12 02/12/14 APS061M–APS199M Locating Pin, 6 mm Thru 19 mm Dia. (Full Metric) I-13 04/30/15 APS250M–APS259M Locating Pin, 25 mm Dia. (Full Metric) I-14 04/30/15 APE061M–APE199M Locating Pin for 6 x 19 Thru 19 x 25 Slotted Holes (Full Metric) I-15 02/12/14 APE061M – APE199M Locating Pin for 6 x 19 mm Thru 19 x 25 mm Slotted Holes (Full Metric) I-16 04/30/15 APE250M – APE259M Locating Pin for 25 x 31 mm Slotted Holes (Full Metric) I-17 04/30/15 ARP061M – ARP199M Respot Pin, 6 mm Thru 19 mm Dia. (Full Metric) I-18 02/12/14 ARP061M – ARP199M Respot Pin, 6 mm Thru 19 mm Dia. (Full Metric) I-19 04/30/15 ARE061M – ARE199M I-20 02/12/14 ARE061M – ARE199M I-21 04/22/14 Discontinued Respot Pin for 6 x 12 mm Thru 19 x 25 mm Slotted Holes (Full Metric) Respot Pin for 6 x 12 mm Thru 19 x 25 mm Slotted Holes (Full Metric) Locating Pin Retainers I-22 04/22/14 Discontinued Locating Pin Retainers I-23 04/22/14 Discontinued Locating Pin Retainers I-24 04/22/14 Discontinued Locating Pin Retainers I-25 04/22/14 Discontinued Locating Pin Retainers ©1997 Auto/Steel Partnership NAAMS CODE TM www.naamsstandards.org DESCRIPTION This document is Uncontrolled when printed. I-1 LOCATING PINS AND RETAINERS COMPONENTS INDEX TM Assembly 04/30/15 PAGE I-26 DATE 04/22/14 NAAMS CODE Discontinued DESCRIPTION Locating Pin Retainers I-27 04/22/14 Discontinued Locating Pin Retainers I-28 02/12/14 Discontinued Locating Pin 6 mm Thru 19 mm Dia. I-29 04/22/14 Discontinued Locating Pin 6 mm Thru 19 mm Dia. I-30 02/12/14 Discontinued Locating Pin 25 mm Dia. I-31 02/12/14 Discontinued Locating Pin for 6 x 12 mm Thru 19 x 25 mm Discontinued Slotted Holes Locating Pin for 6 x 12 mm Thru 19 x 25 mm I-32 04/22/14 Slotted Holes I-33 02/12/14 Discontinued Locating Pin for 25 x 31 mm Slotted Holes I-34 04/30/15 ARP250M–ARP259M Respot Pin 25 mm Dia. (Full Metric) I-35 04/30/15 APQ081–APQ208 Locating Pin 8 mm Thru 20 mm Dia. (Full Metric) I-36 02/12/14 APQ081–APQ208 Locating Pin 8 mm Thru 20 mm Dia. (Full Metric) I-37 04/30/15 APQ251–APQ408 Locating Pin 25 mm Thru 40 mm Dia. (Full Metric) I-38 02/12/14 APQ251–APQ408 Locating Pin 25 mm Thru 40 mm Dia. (Full Metric) I-39 04/22/14 Discontinued Locating Pin Retainer (Full Metric) 20mm Series I-40 04/22/14 Discontinued Locating Pin Retainer (Full Metric) 20mm Series I-41 02/12/14 APR330M–APR333M Locating Pin Retainer (Full Metric) 20mm Series I-42 02/12/14 APR045M–APR046M Locating Pin Retainer (Full Metric) 20mm Series I-43 04/22/14 Discontinued Locating Pin Retainer (Full Metric) 20mm Series I-44 04/22/14 Discontinued Locating Pin Retainer (Full Metric) 20mm Series I-45 02/12/14 APR075M–APR076M Locating Pin Retainer (Full Metric) 20mm Series I-46 04/22/14 Discontinued Locating Pin Retainer (Full Metric) 20mm Series I-47 02/12/14 APR336M–APR339M Locating Pin Retainer (Full Metric) 20mm Series I-48 04/22/14 Discontinued Locating Pin Retainer (Full Metric) 20mm Series I-49 04/22/14 Discontinued Locating Pin Retainer (Full Metric) 20mm Series I-50 02/12/14 APR077M–APR078M Locating Pin Retainer (Full Metric) 20mm Series I-51 02/12/14 APR250M–APR253M Locating Pin Retainer (Full Metric) 20mm Series I-52 02/12/14 APR255M–APR256M Locating Pin Retainer (Full Metric) 20mm Series I-53 02/12/14 APR201M–APR204M Locating Pin Retainer (Full Metric) 20mm Series I-54 02/12/14 APR211M–APR212M Locating Pin Retainer (Full Metric) 20mm Series I-55 02/12/14 APR260M–APR261M Locating Pin Retainer (Full Metric) 20mm Series ©1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. I-1.1 LOCATING PINS AND RETAINERS COMPONENTS INDEX PAGE DATE NAAMS CODE TM Assembly 02/12/14 DESCRIPTION I-56 02/12/14 APR265M–APR268M Locating Pin Retainer (Full Metric) 20mm Series I-57 02/12/14 APR221M–APR222M Locating Pin Retainer (Full Metric) 20mm Series I-58 02/12/14 APR271M–APR274M Locating Pin Retainer (Full Metric) 20mm Series I-59 02/12/14 APR231M–APR234M Locating Pin Retainer (Full Metric) 20mm Series I-60 02/12/14 APR276M–APR277M Locating Pin Retainer (Full Metric) 20mm Series I-61 02/12/14 APR280M–APR283M Locating Pin Retainer (Full Metric) 20mm Series I-62 02/12/14 APR241M–APR242M Locating Pin Retainer (Full Metric) 20mm Series ©1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. I-1.2 LOCATING PIN RETAINERS (FULL METRIC) G L O B A L S TA N D A R D C O M P O N E N T S TM APR010M, 011M, 012M, 013M Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: ALL DIMENSIONS METRIC UNLESS OTHERWISE NOTED. IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS A F +0.015 -0.00 Ø 16.00 12.50 0 L X X X 25.0 REF. Ø 8H6 (2) HOLES 1.0 x 45° 40.0 35.0 0 L 10.00 +0.03 -0.00 12.50 B 0 L A 30.000 49.0 REF. 15.00 0 L 5.0 NAAMS CODE APR010M APR011M APR012M APR013M A M10 x 1.5 M10 x 1.5 11.0 11.0 ©1997 Auto/Steel Partnership MATERIAL Steel / ASTM A-36 SS type 303 or 304 Steel / ASTM A-36 SS type 303 or 304 www.naamsstandards.org 37.0 25.000 13.0 SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART 13.0 9.0 WT. kg 0.32 0.32 0.32 0.32 This document is Uncontrolled when printed. E C D I–4 LOCATING PIN RETAINERS (FULL METRIC) APR020M, 021M G L O B A L S TA N D A R D C O M P O N E N T S TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: ALL DIMENSIONS METRIC UNLESS OTHERWISE NOTED. IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS A E +0.015 -0.00 Ø 16.00 25.0 REF. 40.0 35.0 0 L 12.5 1.0 x 45° 12.5 0 L 0 L 10.00 +0.03 -0.00 XXX M10 x 1.5 30.000 49.0 REF. 15.00 0 L 37.00 13.0 13.0 5.0 9.0 Ø 8H6 (2) HOLES 50.0 REF. SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR020M APR021M MATERIAL Steel / ASTM A-36 SS type 303 or 304 ©1997 Auto/Steel Partnership www.naamsstandards.org WT. kg 0.32 0.32 D B C This document is Uncontrolled when printed. I–5 LOCATING PIN RETAINERS (FULL METRIC) APR030M, 031M, 032M, 033M G L O B A L S TA N D A R D C O M P O N E N T S TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: ALL DIMENSIONS METRIC UNLESS OTHERWISE NOTED. IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS A E +0.015 -0.00 Ø16.00 12.50 0 L X X X 25.0 REF. Ø 8H6 (2) HOLES 10.00 0 L +0.03 -0.00 12.50 A (2) HOLES 1.0 x 45° 55.0 50.0 45.00 64.0 REF. 30.000 20.0 15.00 0 L NAAMS CODE APR030M APR031M APR032M APR033M A M10 x 1.5 M10 x 1.5 11.0 11.0 ©1997 Auto/Steel Partnership MATERIAL Steel / ASTM A-36 SS type 303 or 304 Steel / ASTM A-36 SS type 303 or 304 www.naamsstandards.org WT. kg 0.45 0.45 0.45 0.45 37.0 25.000 SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART 13.0 13.0 9.0 50.0 REF. D B C This document is Uncontrolled when printed. I–6 LOCATING PIN RETAINERS (FULL METRIC) APR040M, 041M G L O B A L S TA N D A R D C O M P O N E N T S TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: ALL DIMENSIONS METRIC UNLESS OTHERWISE NOTED. IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS Ø16.00 A E +0.015 -0.00 25.0 REF. 1.0 x 45° 55.0 50.0 64.0 REF. 0 L 45.00 30.000 20.0 15.00 Ø 8H6 (2) HOLES 50.0 REF. MATERIAL Steel / ASTM A-36 SS type 303 or 304 ©1997 Auto/Steel Partnership www.naamsstandards.org 9.0 37.00 13.0 13.0 0 L NAAMS CODE APR040M APR041M M10 x 1.5 (2) HOLES 12.5 12.5 0 L 0 L 10.00 +0.03 -0.00 XXX WT. kg 0.45 0.45 D SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART B C This document is Uncontrolled when printed. I–7 LOCATING PIN RETAINERS (FULL METRIC) APR050M, 051M G L O B A L S TA N D A R D C O M P O N E N T S TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 BETWEEN DOWELS ±0.015 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: ALL DIMENSIONS METRIC UNLESS OTHERWISE NOTED. IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS +0.015 -0.00 Ø16.00 A E +0.03 -0.00 10.00 12.50 0 L X X X 25.0 REF. 55.00 9.0 1.0 x 45° 15.00 0 L 30.00 66.0 12.50 15.0 10.00 0 L 35.0 REF. 20.0 75.0 REF. Ø 8H6 (2) HOLES Ø 11.00 SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR050M APR051M MATERIAL Steel / ASTM A-36 SS type 303 or 304 ©1997 Auto/Steel Partnership www.naamsstandards.org WT. kg 0.41 0.41 D B C This document is Uncontrolled when printed. I–8 LOCATING PIN RETAINERS (FULL METRIC) APR060M, 061M, 062M, 063M G L O B A L S TA N D A R D C O M P O N E N T S TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 BETWEEN DOWELS ±0.015 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: ALL DIMENSIONS METRIC UNLESS OTHERWISE NOTED. IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS +0.015 -0.00 +0.03 -0.00 Ø16.00 A E Ø 8H6 (2) HOLES 10.00 12.5 0 L X X X 25.0 REF. 0 L 9.0 15.00 30.00 55.00 66.0 12.5 A 1.0 x 45° 30.0 35.0 20.0 0 L 75.0 REF. SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR060M APR061M APR062M APR063M A M10 x 1.5 M10 x 1.5 Drill & C/Bore for M10 SHCS Drill & C/Bore for M10 SHCS ©1997 Auto/Steel Partnership www.naamsstandards.org MATERIAL Steel / ASTM A-36 SS type 303 or 304 Steel / ASTM A-36 SS type 303 or 304 WT. kg 0.41 0.41 0.41 0.41 This document is Uncontrolled when printed. D B C I–9 LOCATING PIN RETAINERS (FULL METRIC) APR070M, 071M G L O B A L S TA N D A R D C O M P O N E N T S TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 BETWEEN DOWELS ±0.015 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: ALL DIMENSIONS METRIC UNLESS OTHERWISE NOTED. IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS A E +0.015 -0.00 +0.03 -0.00 Ø16.00 10.00 12.50 0 L X X X 15.00 30.00 45.00 1.0 x 45° 9.0 0 L 70.00 81.0 12.50 25.0 REF. 15.0 10.00 0 L 35.0 REF. 20.0 90.0 REF. Ø 8H6 (2) HOLES Ø 11.0 (2) HOLES SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR070M APR071M MATERIAL Steel / ASTM A-36 SS type 303 or 304 ©1997 Auto/Steel Partnership www.naamsstandards.org WT. kg 0.45 0.45 D B C This document is Uncontrolled when printed. I – 10 LOCATING PIN 6mm THRU 19mm DIAMETER (FULL METRIC) G L O B A L S TA N D A R D C O M P O N E N T S TM Assembly 04/30/15 PINS WITH TiN CODES SHALL HAVE 1 TO 2 MICRONS OF TITANIUM NITRIDE ADDED TO SURFACES B, C, AND D (MINIMUM SURFACES). COATING PROCESS SHALL NOT NEGATIVELY IMPACT PIN HARDNESS. SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.015 ALL MACHINED SURFACES TO FLAT. PARALLEL AND PERPINDICULAR TO WITHIN 0.015 T.I.R. TO DATUMS A AND B AND CONCENTRIC TO WITHIN 0.03 T.I.R. MATERIAL: S.A.E. 8620 STEEL HARDNESS: 58 - 62 Rc TO A DEPTH OF 0.5 - 0.7 mm AFTER GRINDING NOTE: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. A F H I Ø 22.0 +0.00 -0.02 10.00 TYP. D D +0.00 -0.03 B RADIUS C RADIUS 0.5 x 45 1.0 - 2.0 R o D G A B L REF. XXX –A – 0.50 - 0.75 R E C 5.0 LEAVE THIS END SOFT 28.0 M10 X 1.5 x 17.0 DEEP 24.0 MAX DRILL DEPTH 1.0 X 45 o Ø15.98 G +0.00 -0.01 –B– TABULATED INFORMATION ON FOLLOWING PAGE ©1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. I – 11 LOCATING PIN 6 mm THRU 19 mm DIAMETER (FULL METRIC) 6 mm Round Hole B Rad = 1.0 C Rad = 18.0 D = 5.85 NAAMS CODE TM Assembly 8 mm Round Hole B Rad = 1.0 C Rad = 24.0 D = 7.85 TiN CODE A L WT. kg NAAMS CODE TiN CODE 02/12/14 10 mm Round Hole B Rad = 2.0 C Rad = 30.0 D = 9.85 A L WT. kg NAAMS CODE TiN CODE A A L WT. kg APS061M APS061MT 15.0 51.8 0.05 APS081M APS081MT 15.0 55.1 0.05 APS101M APS101MT 15.0 57.4 0.06 APS062M APS062MT 20.0 56.8 0.05 APS082M APS082MT 20.0 60.1 0.05 APS102M APS102MT 20.0 62.4 0.06 APS063M APS063MT 30.0 66.8 0.05 APS083M APS083MT 30.0 70.1 0.06 APS103M APS103MT 30.0 72.4 0.07 APS064M APS064MT 40.0 76.8 0.05 APS084M APS084MT 40.0 80.1 0.06 APS104M APS104MT 40.0 82.4 0.07 APS065M APS065MT 50.0 86.8 0.06 APS085M APS085MT 50.0 90.1 0.06 APS105M APS105MT 50.0 92.4 0.08 APS066M APS066MT 60.0 96.8 0.06 APS086M APS086MT 60.0 100.1 0.07 APS106M APS106MT 60.0 102.4 0.08 APS087M APS087MT 70.0 110.1 0.07 APS107M APS107MT 70.0 112.4 0.09 APS088M APS088MT 80.0 120.1 0.08 APS108M APS108MT 80.0 122.4 0.10 APS109M APS109MT 90.0 132.4 0.10 APS100M APS100MT 100.0 142.4 0.11 12 mm Round Hole B Rad = 2.0 C Rad = 36.0 D = 11.85 NAAMS CODE TiN CODE A L WT. kg APS121M APS121MT 15.0 60.8 0.07 APS122M APS122MT 20.0 65.8 0.07 APS123M APS123MT 30.0 75.8 0.08 APS124M APS124MT 40.0 85.8 0.09 APS125M APS125MT 50.0 95.8 0.10 APS126M APS126MT 60.0 105.8 0.11 APS127M APS127MT 70.0 115.8 0.12 APS128M APS128MT 80.0 125.8 0.13 APS129M APS129MT 90.0 135.8 0.13 APS120M APS120MT 100.0 145.8 0.14 13 mm Round Hole B Rad = 2.0 C Rad = 39.0 D = 12.85 NAAMS CODE TiN CODE B 19 mm Round Hole B Rad = 2.0 C Rad = 38.0 D = 18.85 16 mm Round Hole B Rad = 2.0 C Rad = 48.0 D = 15.85 A L WT. kg NAAMS CODE TiN CODE A L WT. kg NAAMS CODE TiN CODE A L WT. kg APS131M APS131MT 15.0 62.4 0.07 APS161M APS161MT 15.0 67.5 0.09 APS191M APS191MT 15.0 66.8 0.10 APS132M APS132MT 20.0 67.4 0.07 APS162M APS162MT 20.0 72.5 0.09 APS192M APS192MT 20.0 71.8 0.12 APS133M APS133MT 30.0 77.4 0.08 APS163M APS163MT 30.0 82.5 0.11 APS193M APS193MT 30.0 81.8 0.14 APS134M APS134MT 40.0 87.4 0.09 APS164M APS164MT 40.0 92.5 0.13 APS194M APS194MT 40.0 91.8 0.16 APS135M APS135MT 50.0 97.4 0.10 APS165M APS165MT 50.0 102.5 0.14 APS195M APS195MT 50.0 101.8 0.18 APS136M APS136MT 60.0 107.4 0.11 APS166M APS166MT 60.0 112.5 0.16 APS196M APS196MT 60.0 111.8 0.20 APS137M APS137MT 70.0 117.4 0.12 APS167M APS167MT 70.0 122.5 0.17 APS197M APS197MT 70.0 121.8 0.22 APS138M APS138MT 80.0 127.4 0.13 APS168M APS168MT 80.0 132.5 0.19 APS198M APS198MT 80.0 131.8 0.24 APS139M APS139MT 90.0 137.4 0.14 APS169M APS169MT 90.0 142.5 0.20 APS199M APS199MT 90.0 141.8 0.27 APS130M APS130MT 100.0 147.4 0.15 APS160M APS160MT 100.0 152.5 0.22 APS190M APS190MT 100.0 151.8 0.29 ©1997 Auto/Steel Partnership www.naamsstandards.org C This document is Uncontrolled when printed. I-12 LOCATING PIN 25mm DIAMETER (FULL METRIC) Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.015 ALL MACHINED SURFACES TO FLAT. PARALLEL AND PERPINDICULAR TO WITHIN 0.015 T.I.R. TO DATUMS A AND B AND CONCENTRIC TO WITHIN 0.03 T.I.R. MATERIAL: S.A.E. 8620 STEEL HARDNESS: 58 - 62 Rc TO A DEPTH OF 0.5 - 0.7 mm AFTER GRINDING NOTE: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. G L O B A L S TA N D A R D C O M P O N E N T S TM Assembly 04/30/15 PINS WITH TiN CODES SHALL HAVE 1 TO 2 MICRONS OF TITANIUM NITRIDE ADDED TO ALL SURFACES ABOVE THE -A- DATUM (MINIMUM SURFACES). COATING PROCESS SHALL NOT NEGATIVELY IMPACT PIN HARDNESS. SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART A F J 10.00 TYP. L +0.00 -0.03 Ø 24.85 +0.00 -0.02 D 2.0 RADIUS 50.0 RADIUS 6.0 G 0.5 x 45 o L REF. A D XXX B –A– NAAMS CODE TiN CODE A L WT kg APS251M APS251MT 15.0 74.8 0.15 APS252M APS252MT 20.0 79.8 0.17 APS253M APS253MT 30.0 89.8 0.21 APS254M APS254MT 40.0 99.8 0.24 APS255M APS255MT 50.0 109.8 0.28 APS256M APS256MT 60.0 119.8 0.32 APS257M APS257MT 70.0 129.8 0.36 E 28.0 0.50 - 0.75 R C M10 X 1.5 x 17.0 DEEP 24.0 MAX DRILL DEPTH H K 1.0 X 45 o LEAVE THIS END SOFT APS258M APS258MT 80.0 139.8 0.39 Ø 15.98 +0.00 -0.01 I –B– APS259M APS259MT 90.0 149.8 0.43 APS250M APS250MT 100.0 159.8 0.47 ©1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. I – 13 LOCATING PIN FOR 6 x 12 THRU 19 x 25 mm SLOTTED HOLES (FULL METRIC) Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.015 ALL MACHINED SURFACES TO FLAT. PARALLEL AND PERPINDICULAR TO WITHIN 0.015 T.I.R. TO DATUMS A AND B AND CONCENTRIC TO WITHIN 0.03 T.I.R. MATERIAL: S.A.E. 8620 STEEL HARDNESS: 58 - 62 Rc TO A DEPTH OF 0.5 - 0.7 mm AFTER GRINDING NOTE: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX . D G L O B A L S TA N D A R D C O M P O N E N T S TM Assembly 04/30/15 PINS WITH TiN CODES SHALL HAVE 1 TO 2 MICRONS OF TITANIUM NITRIDE ADDED TO SURFACES B, C, D AND E (MINIMUM SURFACES). COATING PROCESS SHALL NOT NEGATIVELY IMPACT PIN HARDNESS. SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART A E G H +0.30 -0.00 Ø 25.0 G E +0.00 -0.02 FLAT G +0.00 -0.03 10.00 TYP. B RADIUS C RADIUS 1.0 - 2.0 R 0.5 x 45 o G 5.0 (MAX) G A D L REF. XXX –A– 0.5 - 0.75 R C 5.0 28.0 M10 x 1.5 x 17.0 DEEP 24.0 MAX DRILL DEPTH 1.0 X 45 B F LEAVE THIS END SOFT o Ø 15.98 +0.00 -0.01 –B– TABULATED INFORMATION ON FOLLOWING PAGE ©1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. I – 14 LOCATING PIN FOR 6 x 12 THRU 19 x 25 mm TM SLOTTED HOLES(FULL METRIC) 8 x 14 Slotted Hole B Rad = 1.0 C Rad = 24.0 D = 8.81 E = 7.85 6 x 12 Slotted Hole B Rad = 1.0 C Rad = 18.0 D = 7.09 E = 5.85 NAAMS CODE TiN CODE A L WT. kg NAAMS CODE APE061M APE061MT 15.0 52.9 0.05 APE081M APE081MT APE062M APE062MT 20.0 57.9 0.05 APE082M APE082MT APE063M APE063MT 30.0 67.9 0.05 APE083M APE083MT APE064M APE064MT 40.0 77.9 0.06 APE065M APE065MT 50.0 87.9 0.06 APE066M APE066MT 60.0 97.9 0.06 TiN CODE 12 x 18 Slotted Hole B Rad = 2.0 C Rad = 36.0 D = 12.50 E = 11.85 NAAMS CODE A L WT. kg APE121M TiN CODE APE121MT 15.0 62.2 0.07 APE122M APE122MT 20.0 67.2 0.07 APE123M APE123MT 30.0 77.2 0.08 APE124M APE124MT 40.0 87.2 0.09 APE125M APE125MT 50.0 97.2 0.10 APE126M APE126MT 60.0 107.2 0.11 APE127M APE127MT 70.0 117.2 0.12 APE128M APE128MT 80.0 127.2 0.13 APE129M APE129MT 90.0 137.2 0.14 APE120M APE120MT 100.0 147.2 0.15 13 x 19 Slotted Hole B Rad = 2.0 C Rad = 39.0 D = 13.46 E = 12.85 NAAMS CODE TiN CODE Assembly 02/12/14 10 x 16 Slotted Hole B Rad = 2.0 C Rad = 30.0 D = 10.63 E = 9.85 NAAMS CODE TiN CODE L WT. kg 15.0 56.0 0.05 APE101M APE101MT 20.0 61.0 0.06 APE102M APE102MT 30.0 71.0 0.06 APE103M APE103MT APE084M APE084MT 40.0 81.0 0.07 APE085M APE085MT 50.0 91.0 0.07 APE086M APE086MT 60.0 101.0 APE087M APE087MT 70.0 APE088M APE088MT 80.0 A A L WT. kg 15.0 58.2 0.06 20.0 63.2 0.06 30.0 73.2 0.07 APE104M APE104MT 40.0 83.2 0.08 APE105M APE105MT 50.0 93.2 0.08 0.08 APE106M APE106MT 60.0 103.2 0.09 111.0 0.08 APE107M APE107MT 70.0 113.2 0.10 121.0 0.08 APE108M APE108MT 80.0 123.2 0.10 APE109M APE109MT 90.0 133.2 0.11 APE100M APE100MT 100.0 143.2 0.12 A B D C 19 x 25 Slotted Hole B Rad = 2.0 C Rad = 38.0 D = 19.27 E = 18.85 16 x 22 Slotted Hole B Rad = 2.0 C Rad = 48.0 D = 16.35 E = 15.85 TiN CODE A L WT. kg NAAMS CODE APE161M APE161MT 15.0 68.0 0.09 APE191M APE191MT 15.0 67.2 0.11 0.08 APE162M APE162MT 20.0 73.0 0.10 APE192M APE192MT 20.0 72.2 0.12 78.1 0.09 APE163M APE163MT 30.0 83.0 0.11 APE193M APE193MT 30.0 82.2 0.14 40.0 88.1 0.10 APE164M APE164MT 40.0 93.0 0.13 APE194M APE194MT 40.0 92.2 0.16 50.0 98.1 0.11 APE165M APE165MT 50.0 103.0 0.15 APE195M APE195MT 50.0 102.2 0.19 APE136M APE136MT 60.0 108.1 0.12 APE166M APE166MT 60.0 113.0 0.16 APE196M APE196MT 60.0 112.2 0.21 APE137M APE137MT 70.0 118.1 0.13 APE167M APE167MT 70.0 123.0 0.18 APE197M APE197MT 70.0 122.2 0.23 APE138M APE138MT 80.0 128.1 0.14 APE168M APE168MT 80.0 133.0 0.20 APE198M APE198MT 80.0 132.2 0.25 APE139M APE139MT 90.0 138.1 0.16 APE169M APE169MT 90.0 143.0 0.21 APE199M APE199MT 90.0 142.2 0.28 APE130M APE130MT 100.0 148.1 0.17 APE160M APE160MT 100.0 153.0 0.23 APE190M APE190MT 100.0 152.2 0.30 A L WT. kg NAAMS CODE APE131M APE131MT 15.0 63.1 0.07 APE132M APE132MT 20.0 68.1 APE133M APE133MT 30.0 APE134M APE134MT APE135M APE135MT ©1997 Auto/Steel Partnership www.naamsstandards.org TiN CODE A This document is Uncontrolled when printed. L WT. kg I-15 G L O B A L S TA N D A R D C O M P O N E N T S LOCATING PIN FOR 25 x 31 mm TM SLOTTED HOLES (FULL METRIC) Assembly Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.015 ALL MACHINED SURFACES TO FLAT. PARALLEL AND PERPINDICULAR TO WITHIN 0.015 T.I.R. TO DATUMS A AND B AND CONCENTRIC TO WITHIN 0.03 T.I.R. MATERIAL: S.A.E. 8620 STEEL HARDNESS: 58 - 62 Rc TO A DEPTH OF 0.5 - 0.7 mm AFTER GRINDING NOTE: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. 04/30/15 PINS WITH TiN CODES SHALL HAVE 1 TO 2 MICRONS OF TITANIUM NITRIDE ADDED TO ALL SURFACES ABOVE THE -A- DATUM (MINIMUM SURFACES) COATING PROCESS SHALL NOT NEGATIVELY IMPACT PINHARDNESS. SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART. A F I K 10.00 +0.00 -0.03 G +0.00 -0.02 24.85 FLAT 10.00 Ø 25.17 +0.00 -0.03 +0.00 -0.02 G 2.0 RADIUS 50.0 RADIUS 5.0 MAX 0.5x45 G o G L REF. A XXX –A– NAAMS CODE TiN CODE A L APE251M APE251MT 15.0 75.1 0.15 APE252M APE252MT 20.0 80.1 0.17 APE253M APE253MT 30.0 90.1 0.21 0.50 - 0.75 R 6.0 WT kg 28.0 D M10 x 1.5 TAP 17.0 DEEP 24.0 MAX DRILL DEPTH LEAVE THIS END SOFT B C APE254M APE254MT 40.0 100.1 0.25 APE255M APE255MT 50.0 110.1 0.29 1.0 X 45 o Ø 15.98 APE256M APE256MT 60.0 120.1 0.33 E +0.00 -0.01 G APE257M APE257MT 70.0 130.1 0.37 APE258M APE258MT 80.0 140.1 0.40 H –B– APE259M APE259MT 90.0 150.1 0.44 J APE250M APE250MT 100.0 160.1 0.48 ©1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. I – 16 LOCATING PIN 6mm THRU 19mm DIAMETER (FULL METRIC) Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.015 ALL MACHINED SURFACES TO FLAT. PARALLEL AND PERPINDICULAR TO WITHIN 0.015 T.I.R. TO DATUMS A AND B AND CONCENTRIC TO WITHIN 0.03 T.I.R. MATERIAL: S.A.E. 8620 STEEL HARDNESS: 58 - 62 Rc TO A DEPTH OF 0.5 - 0.7 mm AFTER GRINDING NOTE: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. G L O B A L S TA N D A R D C O M P O N E N T S TM Assembly 04/30/15 PINS WITH TiN CODES SHALL HAVE 1 TO 2 MICRONS OF TITANIUM NITRIDE ADDED TO SURFACES B, C AND D (MINIMUM SURFACES). COATING PROCESS SHALL NOT NEGATIVELY IMPACT PIN HARDNESS. SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART A E G H 10.00 +0.00 -0.03 +0.00 -0.02 D Ø 25.0 B RADIUS C RADIUS 0.5 x 45 o 1.0 - 2.0 R G A L REF. B XXX –A– D 0.50 - 0.75 R 5.0 28.0 M10 x 1.5 x 17.0 DEEP 24.0 MAX DRILL 1.0 X 45 o C F LEAVE THIS END SOFT Ø 15.98 +0.00 -0.01 –B– NOTE: DIMENSIONS FOR THIS SERIES OF PINS ARE THE SAME AS FOR THE LOCATING PINS. 6mm THRU 19mm DIAMETER EXCEPT FOR TABULATED INFORMATION ON THE FOLLOWING PAGE ©1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. I – 17 RESPOT PIN 6 mm THRU 19 mm DIAMETER TiN CODE Assembly 8 mm Round Hole B Rad = 1.0 C Rad = 24.0 D = 7.72 6 mm Round Hole B Rad = 1.0 C Rad = 18.0 D = 5.72 NAAMS CODE TM A L WT. kg NAAMS CODE TiN CODE 02/12/14 A 10 mm Round Hole B Rad = 2.0 C Rad = 30.0 D = 9.72 A L WT. kg NAAMS CODE TiN CODE C A L WT. kg ARP061M ARP061MT 15.0 51.8 0.05 ARP081M ARP081MT 15.0 55.1 0.05 ARP101M ARP101MT 15.0 57.4 0.06 ARP062M ARP062MT 20.0 56.8 0.05 ARP082M ARP082MT 20.0 60.1 0.05 ARP102M ARP102MT 20.0 62.4 0.06 ARP063M ARP063MT 30.0 66.8 0.05 ARP083M ARP083MT 30.0 70.1 0.06 ARP103M ARP103MT 30.0 72.4 0.07 ARP064M ARP064MT 40.0 76.8 0.05 ARP084M ARP084MT 40.0 80.1 0.06 ARP104M ARP104MT 40.0 82.4 0.07 ARP065M ARP065MT 50.0 86.8 0.05 ARP085M ARP085MT 50.0 90.1 0.06 ARP105M ARP105MT 50.0 92.4 0.08 0.06 ARP086M ARP086MT 60.0 100.1 0.07 ARP106M ARP106MT 60.0 102.4 0.08 ARP087M ARP087MT 70.0 110.1 0.07 ARP107M ARP107MT 70.0 112.4 0.09 ARP088M ARP088MT 80.0 120.1 0.08 ARP108M ARP108MT 80.0 122.4 0.09 ARP109M ARP109MT 90.0 132.4 0.10 ARP100M ARP100MT 100.0 142.4 0.11 ARP066M ARP066MT 96.8 60.0 12 mm Round Hole B Rad = 2.0 C Rad = 36.0 D = 11.72 NAAMS CODE TiN CODE A L WT. kg ARP121M ARP121MT 15.0 60.8 0.07 ARP122M ARP122MT 20.0 65.8 0.07 ARP123M ARP123MT 30.0 75.8 0.08 ARP124M ARP124MT 40.0 85.8 0.08 ARP125M ARP125MT 50.0 95.8 0.09 ARP126M ARP126MT 60.0 105.8 0.10 ARP127M ARP127MT 70.0 115.8 0.11 ARP128M ARP128MT 80.0 125.8 0.12 ARP129M ARP129MT 90.0 135.8 0.13 ARP120M ARP120MT 100.0 145.8 0.14 13 mm Round Hole B Rad = 2.0 C Rad = 39.0 D = 12.72 NAAMS CODE TiN CODE B 19 mm Round Hole B Rad = 2.0 C Rad = 38.0 D = 18.72 16 mm Round Hole B Rad = 2.0 C Rad = 48.0 D = 15.72 A L WT. kg NAAMS CODE TiN CODE A L WT. kg NAAMS CODE TiN CODE A L WT. kg ARP131M ARP131MT 15.0 62.4 0.07 ARP161M ARP161MT 15.0 67.5 0.08 ARP191M ARP191MT 15.0 66.8 0.10 ARP132M ARP132MT 20.0 67.4 0.07 ARP162M ARP162MT 20.0 72.5 0.09 ARP192M ARP192MT 20.0 71.8 0.11 ARP133M ARP133MT 30.0 77.4 0.08 ARP163M ARP163MT 30.0 82.5 0.10 ARP193M ARP193MT 30.0 81.8 0.14 ARP134M ARP134MT 40.0 87.4 0.09 ARP164M ARP164MT 40.0 92.5 0.12 ARP194M ARP194MT 40.0 91.8 0.16 ARP135M ARP135MT 50.0 97.4 0.10 ARP165M ARP165MT 50.0 102.5 0.13 ARP195M ARP195MT 50.0 101.8 0.18 ARP136M ARP136MT 60.0 107.4 0.11 ARP166M ARP166MT 60.0 112.5 0.15 ARP196M ARP196MT 60.0 111.8 0.20 ARP137M ARP137MT 70.0 117.4 0.12 ARP167M ARP167MT 70.0 122.5 0.16 ARP197M ARP197MT 70.0 121.8 0.22 ARP138M ARP138MT 80.0 127.4 0.13 ARP168M ARP168MT 80.0 132.5 0.18 ARP198M ARP198MT 80.0 131.8 0.24 ARP139M ARP139MT 90.0 137.4 0.14 ARP169M ARP169MT 90.0 142.5 0.20 ARP199M ARP199MT 90.0 141.8 0.26 0.15 ARP160M ARP160MT 100.0 0.21 ARP190M ARP190MT 100.0 151.8 0.28 ARP130M ARP130MT 100.0 147.4 ©1997 Auto/Steel Partnership www.naamsstandards.org 152.5 This document is Uncontrolled when printed. I-18 LOCATING PIN FOR 6 x 12 THRU 19 x 25 mm SLOTTED HOLES (FULL METRIC) Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.015 ALL MACHINED SURFACES TO FLAT. PARALLEL AND PERPINDICULAR TO WITHIN 0.015 T.I.R. TO DATUMS A AND B AND CONCENTRIC TO WITHIN 0.03 T.I.R. MATERIAL: S.A.E. 8620 STEEL HARDNESS: 58 - 62 Rc TO A DEPTH OF 0.5 - 0.7 mm AFTER GRINDING NOTE: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. G L O B A L S TA N D A R D C O M P O N E N T S TM Assembly 04/30/15 PINS WITH TiN CODES SHALL HAVE 1 TO 2 MICRONS OF TITANIUM NITRIDE ADDED TO SURFACES B, C, D AND E (MINIMUM SURFACES). COATING PROCESS SHALL NOT NEGATIVELY IMPACT PIN HARDNESS. SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART A E G H +0.30 D -0.00 Ø 25.0 G E +0.00 -0.02 FLAT G +0.00 -0.03 10.00 TYP. B RADIUS C RADIUS 1.0 - 2.0 R 0.5 x 45 o G 5.0 (MAX) B G A D L REF. XXX –A– 0.5 - 0.75 R F 5.0 28.0 M10 x 1.5 x 17.0 DEEP 24.0 MAX DRILL DEPTH 1.0 X 45 C LEAVE THIS END SOFT o Ø 15.98 +0.00 -0.01 –B– TABULATED INFORMATION ON FOLLOWING PAGE ©1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. I – 19 RESPOT PIN FOR 6 x 12 THRU 19 x 25 mm TM SLOTTED HOLES(FULL METRIC) 8 x 14 Slotted Hole B Rad = 1.0 C Rad = 24.0 D = 8.81 E = 7.72 6 x 12 Slotted Hole B Rad = 1.0 C Rad = 18.0 D = 7.09 E = 5.72 NAAMS CODE Assembly TiN CODE WT. kg L A NAAMS CODE TiN CODE 02/12/14 10 x 16 Slotted Hole B Rad = 2.0 C Rad = 30.0 D = 10.63 E = 9.72 L A WT. kg NAAMS CODE TiN CODE A A L WT. kg ARE061M ARE061MT 15.0 52.9 0.05 ARE081M ARE081MT 15.0 56.0 0.05 ARE101M ARE101MT 15.0 58.2 0.06 ARE062M ARE062MT 20.0 57.9 0.05 ARE082M ARE082MT 20.0 61.0 0.06 ARE102M ARE102MT 20.0 63.2 0.06 ARE063M ARE063MT 30.0 67.9 0.05 ARE083M ARE083MT 30.0 71.0 0.06 ARE103M ARE103MT 30.0 73.2 0.07 ARE064M ARE064MT 40.0 77.9 0.06 ARE084M ARE084MT 40.0 81.0 0.07 ARE104M ARE104MT 40.0 83.2 0.08 ARE065M ARE065MT 50.0 87.9 0.06 ARE085M ARE085MT 50.0 91.0 0.07 ARE105M ARE105MT 50.0 93.2 0.08 ARE066M ARE066MT 60.0 97.9 0.06 ARE086M ARE086MT 60.0 101.0 0.08 ARE106M ARE106MT 60.0 103.2 0.09 ARE087M ARE087MT 70.0 111.0 0.08 ARE107M ARE107MT 70.0 113.2 0.10 ARE088M ARE088MT 80.0 121.0 0.08 ARE108M ARE108MT 80.0 123.2 0.10 ARE109M ARE109MT 90.0 133.2 0.11 ARE100M ARE100MT 100.0 143.2 0.12 12 x 18 Slotted Hole B Rad = 2.0 C Rad = 36.0 D = 12.50 E = 11.72 TiN CODE A L WT. kg ARE121M ARE121MT 15.0 62.2 0.07 ARE122M ARE122MT 20.0 67.2 0.07 ARE123M ARE123MT 30.0 77.2 0.08 ARE124M ARE124MT 40.0 87.2 0.09 ARE125M ARE125MT 50.0 97.2 0.10 ARE126M ARE126MT 60.0 107.2 0.11 ARE127M ARE127MT 70.0 117.2 0.12 ARE128M ARE128MT 80.0 127.2 0.13 ARE129M ARE129MT 90.0 137.2 0.14 ARE120M ARE120MT 100.0 147.2 0.15 NAAMS CODE 13 x 19 Slotted Hole B Rad = 2.0 C Rad = 39.0 D = 13.46 E = 12.72 NAAMS CODE TiN CODE L WT. kg D C 19 x 25 Slotted Hole B Rad = 2.0 C Rad = 38.0 D = 19.27 E = 18.72 16 x 22 Slotted Hole B Rad = 2.0 C Rad = 48.0 D = 16.35 E = 15.72 A B NAAMS CODE TiN CODE A L WT. kg NAAMS CODE TiN CODE A L WT. kg ARE131M ARE131MT 15.0 63.1 0.07 ARE161M ARE161MT 15.0 68.0 0.09 ARE191M ARE191MT 15.0 67.2 0.11 ARE132M ARE132MT 20.0 68.1 0.08 ARE162M ARE162MT 20.0 73.0 0.10 ARE192M ARE192MT 20.0 72.2 0.12 ARE133M ARE133MT 30.0 78.1 0.09 ARE163M ARE163MT 30.0 83.0 0.11 ARE193M ARE193MT 30.0 82.2 0.14 ARE134M ARE134MT 40.0 88.1 0.10 ARE164M ARE164MT 40.0 93.0 0.13 ARE194M ARE194MT 40.0 92.2 0.16 ARE135M ARE135MT 50.0 98.1 0.11 ARE165M ARE165MT 50.0 103.0 0.15 ARE195M ARE195MT 50.0 102.2 0.19 ARE136M ARE136MT 60.0 108.1 0.12 ARE166M ARE166MT 60.0 113.0 0.16 ARE196M ARE196MT 60.0 112.2 0.21 ARE137M ARE137MT 70.0 118.1 0.13 ARE167M ARE167MT 70.0 123.0 0.18 ARE197M ARE197MT 70.0 122.2 0.23 ARE138M ARE138MT 80.0 128.1 0.14 ARE168M ARE168MT 80.0 133.0 0.20 ARE198M ARE198MT 80.0 132.2 0.25 ARE139M ARE139MT 90.0 138.1 0.16 ARE169M ARE169MT 90.0 143.0 0.21 ARE199M ARE199MT 90.0 142.2 0.28 ARE130M ARE130MT 100.0 148.1 0.17 ARE160M ARE160MT 100.0 153.0 0.23 ARE190M ARE190MT 100.0 152.2 0.30 ©1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. I-20 LOCATING PIN RETAINERS G L O B A L S TA N D A R D C O M P O N E N T S TM APR010, 011, 012, 013 Assembly 04/22/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: ALL DIMENSIONS METRIC UNLESS OTHERWISE NOTED. IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO +0.015 -0.00 “SS TYPE” COMPONENTS D IS C O N TI N U ED A 16.00 H DIA. B 12.50 0 L X X X 25.0 REF. G 0 L 10.00 +0.03 -0.00 12.50 P.F. FOR 5/16 DOWEL (2) HOLES 1.0 x 45° 40.0 35.0 0 L A 30.000 49.0 REF. 15.00 0 L 5.0 A 3/8-16 TAP 3/8-16 TAP 13/32 13/32 ©1997 Auto/Steel Partnership MATERIAL Steel / ASTM A-36 SS type 303 or 304 Steel / ASTM A-36 SS type 303 or 304 www.naamsstandards.org 37.0 25.000 50.0 REF. SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR010 APR011 APR012 APR013 13.0 13.0 9.0 WT. kg 0.32 0.32 0.32 0.32 F C D E This document is Uncontrolled when printed. I – 21 LOCATING PIN RETAINERS G L O B A L S TA N D A R D C O M P O N E N T S TM APR020, 021 Assembly 04/22/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: ALL DIMENSIONS METRIC UNLESS OTHERWISE NOTED. IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO "SS TYPE" COMPONENTS. A G D IS C O N TI N U ED +0.015 -0.00 16.00 DIA. 25.0 REF. F 40.0 35.0 0 L 12.5 12.5 1.0 x 45° 0 L 0 L 10.00 +0.03 -0.00 XXX 3/8-16 TAP 30.000 49.0 REF. 15.00 0 L 37.00 13.0 13.0 5.0 9.0 P.F. FOR 5/16 DOWEL (2) HOLES 50.0 REF. E SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR020 APR021 MATERIAL Steel / ASTM A-36 SS type 303 or 304 ©1997 Auto/Steel Partnership www.naamsstandards.org B WT. kg 0.32 0.32 C D This document is Uncontrolled when printed. I – 22 LOCATING PIN RETAINERS G L O B A L S TA N D A R D C O M P O N E N T S TM APR030, 031, 032, 033 Assembly 04/22/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: ALL DIMENSIONS METRIC UNLESS OTHERWISE NOTED. IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. +0.015 NO BLACK OXIDE FINISH -0.00 TO "SS TYPE" COMPONENTS. 16.00 DIA. D IS C O N TI N U ED A G 12.50 0 L X X X F 0 L 10.00 +0.03 -0.00 12.50 25.0 REF. P.F.FOR F F.FOR .FOR 5/16 DOWEL (2) HOLES 1.0 x 45° 55.0 50.0 64.0 REF. 20.0 A (2) HOLES 45.00 30.000 15.00 0 L NAAMS CODE APR030 APR031 APR032 APR033 A 3/8-16 TAP 3/8-16 TAP 13/32 13/32 ©1997 Auto/Steel Partnership MATERIAL Steel / ASTM A-36 SS type 303 or 304 Steel / ASTM A-36 SS type 303 or 304 www.naamsstandards.org WT. kg 0.45 0.45 0.45 0.45 37.0 25.000 SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART 13.0 13.0 9.0 50.0 REF. E B C D This document is Uncontrolled when printed. I – 23 LOCATING PIN RETAINERS G L O B A L S TA N D A R D C O M P O N E N T S TM APR040, 041 Assembly 04/22/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTE: ALL DIMENSIONS METRIC UNLESS OTHERWISE NOTED. IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. +0.015 NO BLACK OXIDE FINISH -0.00 TO "SS TYPE" COMPONENTS. DIA. G D IS C O N TI N U ED 16.00 A F 25.0 REF. 1.0 x 45° 55.0 50.0 64.0 REF. 3/8-16 TAP (2) HOLES 45.00 30.000 20.0 15.00 P.F. FOR 5/16 DOWEL (2) HOLES 50.0 REF. MATERIAL Steel / ASTM A-36 SS type 303 or 304 ©1997 Auto/Steel Partnership 9.0 37.00 13.0 13.0 0 L NAAMS CODE APR040 APR041 0 L 12.5 12.5 0 L 0 L 10.00 +0.03 -0.00 XXX www.naamsstandards.org WT. kg 0.45 0.45 E B SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART C D This document is Uncontrolled when printed. I – 24 LOCATING PIN RETAINERS G L O B A L S TA N D A R D C O M P O N E N T S TM APR050, 051 Assembly 04/22/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 BETWEEN DOWELS ±0.015 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: ALL DIMENSIONS METRIC UNLESS OTHERWISE NOTED. IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO "SS TYPE" COMPONENTS. H D IS C O N TI N U ED +0.015 -0.00 A 16.00 +0.03 -0.00 DIA. 10.00 G 12.50 0 L X X X 25.0 REF. 55.00 9.0 15.00 1.0 x 45° 0 L 30.00 66.0 12.50 B 15.0 10.00 0 L 35.0 REF. 20.0 75.0 REF. P.F. FOR 5/16 DOWEL (2) HOLES 13/32 DIA. F SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR050 APR051 MATERIAL Steel / ASTM A-36 SS type 303 or 304 ©1997 Auto/Steel Partnership www.naamsstandards.org WT. kg 0.41 0.41 C D E This document is Uncontrolled when printed. I – 25 LOCATING PIN RETAINERS G L O B A L S TA N D A R D C O M P O N E N T S TM APR060, 061, 062, 063 Assembly 04/22/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 BETWEEN DOWELS ±0.015 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: ALL DIMENSIONS METRIC UNLESS OTHERWISE NOTED. IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO "SS TYPE" COMPONENTS. A D IS C O N TI N U ED H +0.015 -0.00 16.00 DIA. P.F. FOR 5/16 DOWEL (2) HOLES +0.03 -0.00 10.00 G 12.5 0 L 25.0 REF. B 0 L A 9.0 15.00 30.00 12.5 55.00 66.0 X X X 1.0 x 45° 30.0 35.0 20.0 0 L 75.0 REF. SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR060 APR061 APR062 APR063 A 3/8-16 TAP 3/8-16 TAP Drill & C/Bore for 3/8” SHCS Drill & C/Bore for 3/8” SHCS ©1997 Auto/Steel Partnership www.naamsstandards.org MATERIAL Steel / ASTM A-36 SS type 303 or 304 Steel / ASTM A-36 SS type 303 or 304 WT. kg 0.41 0.41 0.41 0.41 This document is Uncontrolled when printed. F C D E I – 26 LOCATING PIN RETAINERS G L O B A L S TA N D A R D C O M P O N E N T S TM APR070, 071 Assembly 04/22/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 BETWEEN DOWELS ±0.015 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: ALL DIMENSIONS METRIC UNLESS OTHERWISE NOTED. IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO "SS TYPE" COMPONENTS. A D IS C O N TI N U ED H +0.015 -0.00 16.00 G +0.03 -0.00 DIA. 10.00 12.50 0 L X X X 70.00 9.0 30.00 45.00 1.0 x 45° 0 L 15.00 81.0 12.50 25.0 REF. B 15.0 10.00 0 L 35.0 REF. 20.0 90.0 REF. P.F. FOR 5/16 DOWEL (2) HOLES 13/32 DIA. (2) HOLES F SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR070 APR071 MATERIAL Steel / ASTM A-36 SS type 303 or 304 ©1997 Auto/Steel Partnership www.naamsstandards.org C WT. kg 0.45 0.45 D E This document is Uncontrolled when printed. I – 27 G L O B A L S TA N D A R D C O M P O N E N T S LOCATING PIN 6mm THRU 19mm DIAMETER TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.015 ALL MACHINED SURFACES TO FLAT. PARALLEL AND PERPINDICULAR TO WITHIN 0.015 T.I.R. TO DATUMS A AND B AND CONCENTRIC TO WITHIN 0.03 T.I.R. MATERIAL: S.A.E. 8620 STEEL HARDNESS: 58 - 62 Rc TO A DEPTH OF 0.5 - 0.7 mm AFTER GRINDING NOTE: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. A F H D IS C O N TI N U ED SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART I Ø 22.0 +0.00 -0.02 10.00 TYP. D D +0.00 -0.03 B RADIUS C RADIUS 0.5 x 45 1.0 - 2.0 R o G A D B L REF. XXX –A – 0.50 - 0.75 R E C 5.0 LEAVE THIS END SOFT 28.0 3/8 x 16 TAP 17.0 mm DEEP 24.0 MAX DRILL DEPTH 1.0 X 45 o Ø15.98 G +0.00 -0.01 –B– TABULATED INFORMATION ON FOLLOWING PAGE ©1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. I – 28 LOCATING PIN 6 mm THRU 19 mm DIAMETER 6 mm Round Hole B Rad = 1.0 C Rad = 18.0 D = 5.85 NAAMS TiN CODE CODE TM Assembly 8 mm Round Hole B Rad = 1.0 C Rad = 24.0 D = 7.85 A L 04/22/14 10 mm Round Hole B Rad = 2.0 C Rad = 30.0 D = 9.85 WT. NAAMS TiN kg CODE CODE A L WT. NAAMS TiN kg CODE CODE A WT. L A kg 51.8 0.05 APS081 APS081T 15.0 55.1 0.05 APS101 APS101T 15.0 57.4 0.06 APS062 APS062T 20.0 56.8 0.05 APS082 APS082T 20.0 60.1 0.05 APS102 APS102T 20.0 62.4 0.06 APS063 APS063T 30.0 66.8 0.05 APS083 APS083T 30.0 70.1 0.06 APS103 APS103T 30.0 72.4 0.07 APS064 APS064T 40.0 76.8 0.05 APS084 APS084T 40.0 80.1 0.06 APS104 APS104T 40.0 82.4 0.07 APS065 APS065T 50.0 86.8 0.06 APS085 APS085T 50.0 90.1 0.06 APS105 APS105T 50.0 92.4 0.08 APS066 APS066T 60.0 96.8 0.06 APS086 APS086T 60.0 100.1 0.07 APS106 APS106T 60.0 102.4 0.08 APS087 APS087T 70.0 110.1 0.07 APS107 APS107T 70.0 112.4 0.09 APS088 APS088T 80.0 120.1 0.08 APS108 APS108T 80.0 122.4 0.10 D IS C O N TI N U ED APS061 APS061T 15.0 C APS109 APS109T 90.0 132.4 0.10 APS100 APS100T 100.0 142.4 0.11 13 mm Round Hole B Rad = 2.0 C Rad = 39.0 D = 12.85 NAAMS 16 mm Round Hole B Rad = 2.0 C Rad = 48.0 D = 15.85 TiN WT. NAAMS TiN CODE CODE B 19 mm Round Hole B Rad = 2.0 C Rad = 38.0 D = 18.85 WT. NAAMS TiN kg CODE CODE 15.0 67.5 0.09 APS191 APS191T 15.0 66.8 0.10 APS162 APS162T 20.0 72.5 0.09 APS192 APS192T 20.0 71.8 0.12 77.4 0.08 APS163 APS163T 30.0 82.5 0.11 APS193 APS193T 30.0 81.8 0.14 40.0 87.4 0.09 APS164 APS164T 40.0 92.5 0.13 APS194 APS194T 40.0 91.8 0.16 APS135T 50.0 97.4 0.10 APS165 APS165T 50.0 102.5 0.14 APS195 APS195T 50.0 101.8 0.18 APS136T 60.0 107.4 0.11 APS166 APS166T 60.0 112.5 0.16 APS196 APS196T 60.0 111.8 0.20 APS137T 70.0 117.4 0.12 APS167 APS167T 70.0 122.5 0.17 APS197 APS197T 70.0 121.8 0.22 APS138 APS138T 80.0 127.4 0.13 APS168 APS168T 80.0 132.5 0.19 APS198 APS198T 80.0 131.8 0.24 APS139 APS139T 90.0 137.4 0.14 APS169 APS169T 90.0 142.5 0.20 APS199 APS199T 90.0 141.8 0.27 APS130 APS130T 100.0 147.4 0.15 APS160 APS160T 100.0 152.5 0.22 APS190 APS190T 100.0 151.8 0.29 CODE APS131 APS132 APS133 APS134 APS135 APS136 APS137 CODE A APS131T 15.0 62.4 0.07 APS161 APS161T APS132T 20.0 67.4 0.07 APS133T 30.0 APS134T L kg ©1997 Auto/Steel Partnership www.naamsstandards.org A L This document is Uncontrolled when printed. WT. A L kg I-29 G L O B A L S TA N D A R D C O M P O N E N T S LOCATING PIN 25mm DIAMETER TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.015 ALL MACHINED SURFACES TO FLAT. PARALLEL AND PERPINDICULAR TO WITHIN 0.015 T.I.R. TO DATUMS A AND B AND CONCENTRIC TO WITHIN 0.03 T.I.R. MATERIAL: S.A.E. 8620 STEEL HARDNESS: 58 - 62 Rc TO A DEPTH OF 0.5 - 0.7 mm AFTER GRINDING NOTE: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. A F I D IS C O N TI N U ED SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHA0RT 10.00 TYP. +0.00 -0.03 Ø 24.85 J +0.00 -0.02 D 2.0 RADIUS 50.0 RADIUS 6.0 G 0.5 x 45 o L REF. A D XXX E –A– NAAMS CODE APS251 APS252 APS253 APS254 APS255 APS256 APS257 APS258 APS259 APS250 A L WT kg 15.0 20.0 30.0 40.0 50.0 60.0 70.0 80.0 90.0 100.0 74.8 79.8 89.8 99.8 109.8 119.8 129.8 139.8 149.8 159.8 0.15 0.17 0.21 0.24 0.28 0.32 0.36 0.39 0.43 0.47 ©1997 Auto/Steel Partnership 3/8 X 16 TAP 17.0 mm DEEP 24.0 MAX DRILL DEPTH 1.0 X 45 o www.naamsstandards.org C 0.50 - 0.75 R 28.0 LEAVE THIS END SOFT B Ø 15.98 G +0.00 -0.01 H –B– This document is Uncontrolled when printed. I – 30 LOCATING PIN FOR 6 x 12 THRU 19 x 25 mm SLOTTED HOLES G L O B A L S TA N D A R D C O M P O N E N T S TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.015 ALL MACHINED SURFACES TO FLAT. PARALLEL AND PERPINDICULAR TO WITHIN 0.015 T.I.R. TO DATUMS A AND B AND CONCENTRIC TO WITHIN 0.03 T.I.R. MATERIAL: S.A.E. 8620 STEEL HARDNESS: 58 - 62 Rc TO A DEPTH OF 0.5 - 0.7 mm AFTER GRINDING NOTE: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. A E G D IS C O N TI N U ED SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART +0.30 D -0.00 Ø 25.0 G E +0.00 -0.02 H FLAT G +0.00 -0.03 10.00 TYP. B RADIUS C RADIUS 1.0 - 2.0 R 0.5 x 45 o G 5.0 (MAX) G A D L REF. XXX –A– 0.5 - 0.75 R C 5.0 28.0 3/8 x 16 TAP 17.0 mm DEEP 24.0 MAX DRILL DEPTH 1.0 X 45 B F LEAVE THIS END SOFT o Ø 15.98 +0.00 -0.01 –B– TABULATED INFORMATION ON FOLLOWING PAGE ©1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. I – 31 LOCATING PIN FOR 6 x 12 THRU 19 x 25 mm SLOTTED HOLES TM Assembly 8 x 14 Slotted Hole B Rad = 1.0 C Rad = 24.0 D = 8.81 E = 7.85 6 x 12 Slotted Hole B Rad = 1.0 C Rad = 18.0 D = 7.09 E = 5.85 04/22/14 10 x 16 Slotted Hole B Rad = 2.0 C Rad = 30.0 D = 10.63 E = 9.85 NAAMS TiN CODE CODE APE061 APE061T APE062 APE062T 20.0 57.9 0.05 APE082 APE082T 20.0 61.0 0.06 APE102 APE102T 20.0 63.2 0.06 APE063 APE063T 30.0 67.9 0.05 APE083 APE083T 30.0 71.0 0.06 APE103 APE103T 30.0 73.2 0.07 APE064 APE064T 40.0 77.9 0.06 APE084 APE084T 40.0 81.0 0.07 APE104 APE104T 40.0 83.2 0.08 APE065 APE065T 50.0 87.9 0.06 APE085 APE085T 50.0 91.0 0.07 APE105 APE105T 50.0 93.2 0.08 APE066 APE066T 60.0 97.9 0.06 APE086 APE086T 60.0 101.0 0.08 APE106 APE106T 60.0 103.2 0.09 APE087 APE087T 70.0 111.0 0.08 APE107 APE107T 70.0 113.2 0.10 APE088 APE088T 80.0 121.0 0.08 APE108 APE108T 80.0 123.2 0.10 APE109 APE109T 90.0 133.2 0.11 APE100 APE100T 100.0 143.2 0.12 A L WT. NAAMS TiN kg CODE CODE 13 x 19 Slotted Hole B Rad = 2.0 C Rad = 39.0 D = 13.46 E = 12.85 NAAMS CODE APE081 APE081T L WT. NAAMS TiN kg CODE CODE APE101 APE101T 15.0 56.0 0.05 WT. A A L WT. NAAMS TiN kg CODE CODE kg A L WT. NAAMS TiN kg CODE CODE A WT. L kg APE131 APE131T 15.0 63.1 0.07 APE161 APE161T 15.0 68.0 0.09 APE191 APE191T 15.0 67.2 0.11 APE132 APE132T 20.0 68.1 0.08 APE162 APE162T 20.0 73.0 0.10 APE192 APE192T 20.0 72.2 0.12 APE133 APE133T 30.0 78.1 0.09 APE163 APE163T 30.0 83.0 0.11 APE193 APE193T 30.0 82.2 0.14 APE134 APE134T 40.0 88.1 0.10 APE164 APE164T 40.0 93.0 0.13 APE194 APE194T 40.0 92.2 0.16 APE135 APE135T 50.0 98.1 0.11 APE165 APE165T 50.0 103.0 0.15 APE195 APE195T 50.0 102.2 0.19 APE136 APE136T 60.0 108.1 0.12 APE166 APE166T 60.0 113.0 0.16 APE196 APE196T 60.0 112.2 0.21 APE137 APE137T 70.0 118.1 0.13 APE167 APE167T 70.0 123.0 0.18 APE197 APE197T 70.0 122.2 0.23 APE138 APE138T 80.0 128.1 0.14 APE168 APE168T 80.0 133.0 0.20 APE198 APE198T 80.0 132.2 0.25 APE139 APE139T 90.0 138.1 0.16 APE169 APE169T 90.0 143.0 0.21 APE199 APE199T 90.0 142.2 0.28 APE130 APE130T 100.0 148.1 0.17 APE160 APE160T 100.0 153.0 0.23 APE190 APE190T 100.0 152.2 0.30 ©1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. A B D C 19 x 25 Slotted Hole B Rad = 2.0 C Rad = 38.0 D = 19.27 E = 18.85 16 x 22 Slotted Hole B Rad = 2.0 C Rad = 48.0 D = 16.35 E = 15.85 TiN CODE L 15.0 58.2 0.06 D IS C O N TI N U ED 15.0 52.9 0.05 A I-32 LOCATING PIN FOR 25 x 31 mm SLOTTED HOLES G L O B A L S TA N D A R D C O M P O N E N T S TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.015 ALL MACHINED SURFACES TO FLAT. PARALLEL AND PERPINDICULAR TO WITHIN 0.015 T.I.R. TO DATUMS A AND B AND CONCENTRIC TO WITHIN 0.03 T.I.R. MATERIAL: S.A.E. 8620 STEEL HARDNESS: 58 - 62 Rc TO A DEPTH OF 0.5 - 0.7 mm AFTER GRINDING NOTE: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. A E J SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART +0.00 -0.03 D IS C O N TI N U ED 10.00 G +0.00 -0.02 24.85 FLAT 10.00 Ø 25.17 +0.00 -0.03 +0.00 -0.02 G K 2.0 RADIUS 50.0 RADIUS 5.0 MAX 0.5x45 G o G L REF. A –A– NAAMS CODE A L WT kg APE251 APE252 APE253 APE254 APE255 APE256 APE257 APE258 APE259 APE250 15.0 20.0 30.0 40.0 50.0 60.0 70.0 80.0 90.0 100.0 75.1 80.1 90.1 100.1 110.1 120.1 130.1 140.1 150.1 160.1 0.15 0.17 0.21 0.25 0.29 0.33 0.37 0.40 0.44 0.48 ©1997 Auto/Steel Partnership I 0.50 - 0.75 R 6.0 28.0 B 3/8-16 TAP 17.0 DEEP 24.0 MAX DRILL DEPTH LEAVE THIS END SOFT 1.0 X 45 XXX o www.naamsstandards.org Ø 15.98 D C F +0.00 -0.01 G H –B– This document is Uncontrolled when printed. I – 33 RESPOT PIN 25mm DIAMETER (FULL METRIC) G L O B A L S TA N D A R D C O M P O N E N T S TM Assembly Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.015 ALL MACHINED SURFACES TO FLAT. PARALLEL AND PERPINDICULAR TO WITHIN 0.015 T.I.R. TO DATUMS A AND B AND CONCENTRIC TO WITHIN 0.03 T.I.R. MATERIAL: S.A.E. 8620 STEEL HARDNESS: 58 - 62 Rc TO A DEPTH OF 0.5 - 0.7 mm AFTER GRINDING NOTE: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. 04/30/15 I PINS WITH TiN CODES SHALL HAVE 1 TO 2 MICRONS OF TITANIUM NITRIDE ADDED TO ALL SURFACES ABOVE THE -A- DATUM (MINIMUM SURFACES). COATING PROCESS SHALL NOT NEGATIVELY IMPACT PIN HARDNESS. SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART C F K 10.00 TYP. +0.00 -0.03 Ø 24.72 +0.00 -0.02 G 2.0 RADIUS 50.0 RADIUS 6.0 G 0.5 x 45 o L REF. A H XXX B –A– NAAMS CODE TiN CODE A L WT kg ARP251M ARP251MT 15.0 74.8 0.15 ARP252M ARP252MT 20.0 79.8 0.17 ARP253M ARP253MT 30.0 89.8 0.21 ARP254M ARP254MT 40.0 99.8 0.25 ARP255M ARP255MT 50.0 109.8 0.29 ARP256M ARP256MT 60.0 119.8 0.33 ARP257M ARP257MT 70.0 129.8 0.37 ARP258M ARP258MT 80.0 139.8 0.40 ARP259M ARP259MT 90.0 149.8 0.44 A M10 X 1.5 x 17.0 DEEP 24.0 MAX DRILL DEPTH 1.0 X 45 o LEAVE THIS END SOFT J 0.50 - 0.75 R 28.0 Ø 15.98 D +0.00 -0.01 E –B– ARP250M ARP250MT 100.0 159.8 0.48 ©1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. I – 34 LOCATING PIN 8mm THRU 20mm DIAMETER (FULL METRIC) G L O B A L S TA N D A R D C O M P O N E N T S TM Assembly 04/30/15 PINS WITH TiN CODES SHALL HAVE 1 TO 2 MICRONS OF TITANIUM NITRIDE ADDED TO SURFACES B, C AND D (MINIMUM SURFACES). COATING PROCESS SHALL NOT NEGATIVELY IMPACT PIN HARDNESS. SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.015 ALL MACHINED SURFACES TO FLAT. PARALLEL AND PERPINDICULAR TO WITHIN 0.015 T.I.R. TO DATUMS A AND B AND CONCENTRIC TO WITHIN 0.03 T.I.R. MATERIAL: S.A.E. 8620 STEEL HARDNESS: 58 - 62 Rc TO A DEPTH OF 0.5 - 0.7 mm AFTER GRINDING NOTE: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. A C D Ø 22.0 h6 10.00 TYP. D +0.00 -0.03 B RADIUS C RADIUS 0.5 x 45 1.0 - 2.0 R o G A L REF. XXX –A – 0.50 - 0.75 R 5.0 LEAVE THIS END SOFT 28.0 M10 X 1.5 x 17.0 DEEP 24.0 MAX DRILL DEPTH 1.0 X 45 o Ø15.98 B +0.00 -0.01 –B– TABULATED INFORMATION ON FOLLOWING PAGE ©1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. I – 35 LOCATING PIN 8 mm THRU 20 mm DIAMETER (FULL METRIC) 8 mm Round Hole B Rad = 1.0 C Rad = 24.0 D = 8 h6 NAAMS CODE TiN CODE TM Assembly 10 mm Round Hole B Rad = 1.0 C Rad = 30.0 D = 10 h6 A L WT. kg NAAMS TiN CODE CODE 02/12/14 13 mm Round Hole B Rad = 2.0 C Rad = 30.0 D = 13 h6 A L WT. kg NAAMS CODE TiN CODE A A L WT. kg APQ081 APQ081T 15.0 55.4 0.05 APQ101 APQ101T 15.0 58.7 0.06 APQ131 APQ131T 15.0 60.2 0.07 APQ082 APQ082T 20.0 60.4 0.05 APQ102 APQ102T 20.0 63.7 0.06 APQ132 APQ132T 20.0 65.2 0.07 APQ083 APQ083T 30.0 70.4 0.06 APQ103 APQ103T 30.0 73.7 0.07 APQ133 APQ133T 30.0 75.2 0.08 APQ084 APQ084T 40.0 80.4 0.06 APQ104 APQ104T 40.0 83.7 0.07 APQ134 APQ134T 40.0 85.2 0.09 APQ085 APQ085T 50.0 90.4 0.07 APQ105 APQ105T 50.0 93.7 0.08 APQ135 APQ135T 50.0 95.2 0.10 APQ086 APQ086T 60.0 100.4 0.07 APQ106 APQ106T 60.0 103.7 0.09 APQ136 APQ136T 60.0 105.2 0.12 APQ107 APQ107T 70.0 113.7 0.09 APQ137 APQ137T 70.0 115.2 0.13 APQ108 APQ108T 80.0 123.7 0.10 APQ138 APQ138T 80.0 125.2 0.14 A L WT. kg 16 mm Round Hole B Rad = 2.0 C Rad = 48.0 D = 16 h6 NAAMS CODE L WT. kg NAAMS TiN CODE CODE APQ161 APQ161T 15.0 67.7 0.08 APQ162 APQ162T 20.0 72.7 APQ163 APQ163T 30.0 82.7 APQ164 APQ164T 40.0 TiN CODE 20 mm Round Hole B Rad = 2.0 C Rad = 38.0 D = 20 h6 18 mm Round Hole B Rad = 2.0 C Rad = 38.0 D = 18 h6 NAAMS TiN CODE CODE A L WT. kg APQ181 APQ181T 15.0 66.3 0.10 APQ201 APQ201T 15.0 67.6 0.11 0.09 APQ182 APQ182T 20.0 71.3 0.11 APQ202 APQ202T 20.0 72.6 0.13 0.11 APQ183 APQ183T 30.0 81.3 0.13 APQ203 APQ203T 30.0 82.6 0.15 92.7 0.12 APQ184 APQ184T 40.0 91.3 0.15 APQ204 APQ204T 40.0 92.6 0.17 APQ165 APQ165T 50.0 102.7 0.14 APQ185 APQ185T 50.0 101.3 0.17 APQ205 APQ205T 50.0 102.6 0.20 APQ166 APQ166T 60.0 112.7 0.15 APQ186 APQ186T 60.0 111.3 0.19 APQ206 APQ206T 60.0 112.6 0.22 APQ167 APQ167T 70.0 122.7 0.17 APQ187 APQ187T 70.0 121.3 0.21 APQ207 APQ207T 70.0 122.6 0.25 APQ168 APQ168T 80.0 132.7 0.19 APQ188 APQ188T 80.0 131.3 0.23 APQ208 APQ208T 80.0 132.6 0.27 A ©1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. I-36 B C LOCATING PIN 25mm THRU 40mm DIAMETER (FULL METRIC) Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.015 ALL MACHINED SURFACES TO FLAT. PARALLEL AND PERPINDICULAR TO WITHIN 0.015 T.I.R. TO DATUMS A AND B AND CONCENTRIC TO WITHIN 0.03 T.I.R. MATERIAL: S.A.E. 8620 STEEL HARDNESS: 58 - 62 Rc TO A DEPTH OF 0.5 - 0.7 mm AFTER GRINDING NOTE: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. G L O B A L S TA N D A R D C O M P O N E N T S TM Assembly 04/30/15 A PINS WITH TiN CODES SHALL HAVE 1 TO 2 MICRONS OF TITANIUM NITRIDE ADDED TO ALL SURFACES ABOVE THE -A- DATUM (MINIMUM SURFACES). COATING PROCESS SHALL NOT NEGATIVELY IMPACT PIN HARDNESS. SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART B D 10.00 TYP. E +0.00 -0.03 D h6 2.0 RADIUS 50.0 RADIUS 6.0 0.5 x 45 G o L REF. A XXX –A– 0.50 - 0.75 R 28.0 1.0 X 45 o LEAVE THIS END SOFT ©1997 Auto/Steel Partnership C M10 X 1.5 x 17.0 DEEP 24.0 MAX DRILL DEPTH Ø 15.98 +0.00 -0.01 –B– www.naamsstandards.org This document is Uncontrolled when printed. I – 37 LOCATING PIN 25 mm THRU 40 mm DIAMETER (FULL METRIC) A Assembly L WT. kg NAAMS CODE APQ251 APQ251T 15.0 75.0 0.15 APQ252 APQ252T 20.0 80.0 0.17 A 02/12/14 35 mm Round Hole B Rad = 2.0 C Rad = 50.0 D = 35 h6 30 mm Round Hole B Rad = 2.0 C Rad = 50.0 D = 30 h6 25 mm Round Hole B Rad = 2.0 C Rad = 50.0 D = 25 h6 NAAMS TiN CODE CODE TM TiN CODE A L WT. kg NAAMS CODE APQ301 APQ301T 15.0 77.8 0.22 APQ351 APQ302 APQ302T 20.0 82.8 0.24 TiN CODE C L WT. kg APQ351T 15.0 80.3 0.29 APQ352 APQ352T 20.0 85.3 0.33 A APQ253 APQ253T 30.0 90.0 0.21 APQ303 APQ303T 30.0 92.8 0.30 APQ353 APQ353T 30.0 95.3 0.41 APQ254 APQ254T 40.0 100.0 0.25 APQ304 APQ304T 40.0 102.8 0.35 APQ354 APQ354T 40.0 105.3 0.48 APQ255 APQ255T 50.0 110.0 0.29 APQ305 APQ305T 50.0 112.8 0.41 APQ355 APQ355T 50.0 115.3 0.55 APQ256 APQ256T 60.0 120.0 0.32 APQ306 APQ306T 60.0 122.8 0.46 APQ356 APQ356T 60.0 125.3 0.63 APQ257 APQ257T 70.0 130.0 0.36 APQ307 APQ307T 70.0 132.8 0.52 APQ357 APQ357T 70.0 135.3 0.70 0.40 APQ308 APQ308T 80.0 142.8 0.57 APQ358 APQ358T 80.0 145.3 0.78 APQ258 APQ258T 80.0 140.0 D B 40 mm Round Hole B Rad = 2.0 C Rad = 50.0 D = 40 h6 NAAMS CODE TiN CODE A L APQ401 APQ401T 15.0 82.5 0.39 WT. kg APQ402 APQ402T 20.0 87.5 0.43 APQ403 APQ403T 30.0 97.5 0.53 APQ404 APQ404T 40.0 107.5 0.63 APQ405 APQ405T 50.0 117.5 0.73 APQ406 APQ406T 60.0 127.5 0.82 APQ407 APQ407T 70.0 137.5 0.92 APQ408 APQ408T 80.0 147.5 1.02 ©1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. I-38 LOCATING PIN RETAINER G L O B A L S TA N D A R D C O M P O N E N T S (FULL METRIC) 20 mm SERIES APR310M, 311M, 312M, 313M TM Assembly 04/22/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO "SS TYPE" COMPONENTS. D +0.015 -0.00 Ø 16.00 D IS C O N TI N U ED 15.00 0 L X X X 30.00 REF F.. RE REF. 0 L 1.0 x 45 45°° 40.0 35.0 10.00 +0.03 -0.00 15.00 Ø 6F7 (2) HOLES 0 L E A 30.000 49.0 REF F.. RE REF. 15.00 0 L 5.0 35.0 25.000 15.0 13.0 9.0 48.0 REF. NAAMS CODE APR310M APR311M APR312M APR313M A M8 x 1.25 M8 x 1.25 9.0 9.0 ©1997 Auto/Steel Partnership MATERIAL Steel / ASTM A-36 SS type 303 or 304 Steel / ASTM A-36 SS type 303 or 304 www.naamsstandards.org WT. kg 0.41 0.41 0.41 0.41 SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART This document is Uncontrolled when printed. C A B I – 39 LOCATING PIN RETAINER G L O B A L S TA N D A R D C O M P O N E N T S (FULL METRIC) 20 mm SERIES APR320M, 321M TM Assembly 04/22/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO "SS TYPE" COMPONENTS. E +0.015 -0.00 D IS C O N TI N U ED Ø 16.00 25.0 F.. F REF. 40.0 35.0 0 L 12.5 1.0 x 45° 12.5 0 L 0 L 10.00 +0.03 -0.00 XXX D M8 x 1.25 30.000 49.0 F.. REF. F 15.00 0 L 35.00 15.0 13.0 5.0 48.0 REF. 9.0 Ø 6F7 (2) HOLES SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR320M APR321M MATERIAL Steel / ASTM A-36 SS type 303 or 304 ©1997 Auto/Steel Partnership www.naamsstandards.org C WT. kg 0.41 0.41 A B This document is Uncontrolled when printed. I – 40 LOCATING PIN RETAINER G L O B A L S TA N D A R D C O M P O N E N T S (FULL METRIC) 20 mm SERIES APR330M, 331M, 332M, 333M Ø16.00 TM Assembly Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS +0.015 -0.00 15.00 0 L 02/12/14 X X X D 30.00 REF. 10.00 0 L +0.03 -0.00 15.00 A (2) HOLES 1.0 x 45° Ø 6F7 (2) HOLES 55.0 50.0 45.00 64.0 REF. 30.000 20.0 15.00 0 L 35.0 25.000 13.0 15.0 9.0 48.0 REF. NAAMS CODE APR330M APR331M APR332M APR333M A M8 x 1.25 M8 x 1.25 9.0 9.0 ©1997 Auto/Steel Partnership MATERIAL Steel / ASTM A-36 SS type 303 or 304 Steel / ASTM A-36 SS type 303 or 304 www.naamsstandards.org WT. kg 0.45 0.45 0.45 0.45 C SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART A B This document is Uncontrolled when printed. I – 41 LOCATING PIN RETAINER (FULL METRIC) 20 mm SERIES APR045M, 046M G L O B A L S TA N D A R D C O M P O N E N T S TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS Ø16.00 D +0.015 -0.00 25.0 REF. 1.0 x 45° 55.0 50.0 64.0 REF. 0 L M8 x 1.25 (2) HOLES 12.5 12.5 0 L 0 L 10.00 +0.03 -0.00 XXX 45.00 30.000 20.0 15.00 Ø 6F7 (2) HOLES 48.0 REF. NAAMS CODE APR045M APR046M MATERIAL Steel / ASTM A-36 SS type 303 or 304 ©1997 Auto/Steel Partnership www.naamsstandards.org 9.0 35.00 15.0 13.0 0 L WT. kg 0.32 0.32 C SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART This document is Uncontrolled when printed. A B I – 42 LOCATING PIN RETAINER G L O B A L S TA N D A R D C O M P O N E N T S (FULL METRIC) 20 mm SERIES APR055M, 056M TM Assembly 04/22/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO "SS TYPE" COMPONENTS. +0.015 -0.00 Ø16.00 E D IS C O N TI N U ED +0.03 -0.00 10.00 15.00 0 L X X X 30.00 REF. 55.00 9.0 15.00 1.0 x 45 45°° D 0 L 30.000 66.0 15.00 15.0 10.00 0 L 35.0 REF F.. RE REF. 20.0 75.0 REF. Ø 6F7 (2) HOLES Ø 9.0 SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR055M APR056M MATERIAL Steel / ASTM A-36 SS type 303 or 304 ©1997 Auto/Steel Partnership www.naamsstandards.org C WT. kg 0.50 0.50 A B This document is Uncontrolled when printed. I – 43 LOCATING PIN RETAINER G L O B A L S TA N D A R D C O M P O N E N T S (FULL METRIC) 20 mm SERIES APR065M, 066M, 067M, 068M TM Assembly 04/22/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO "SS TYPE" COMPONENTS. +0.015 -0.00 +0.03 -0.00 Ø16.00 Ø 6F7 (2) HOLES D IS C O N TI N U ED 10.00 E 15.0 0 L X X X 30.0 REF. 0 L 9.0 15.00 30.000 55.00 66.0 15.0 D A 1.0 x 45 45°° 30.0 35.00 25.0 0 L 75.0 REF. SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR065M APR066M APR067M APR068M A M8 x 1.25 M8 x 1.25 Drill & C/Bore for M8 SHCS Drill & C/Bore for M8 SHCS ©1997 Auto/Steel Partnership www.naamsstandards.org MATERIAL Steel / ASTM A-36 SS type 303 or 304 Steel / ASTM A-36 SS type 303 or 304 WT. kg 0.50 0.50 0.50 0.50 This document is Uncontrolled when printed. C A B I – 44 LOCATING PIN RETAINER (FULL METRIC) 20 mm SERIES APR075M, 076M G L O B A L S TA N D A R D C O M P O N E N T S TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS +0.015 -0.00 D +0.03 -0.00 Ø16.00 10.00 15.00 0 L X X X 30.00 REF. 15.00 30.000 45.00 1.0 x 45° 9.0 0 L 70.00 81.0 15.00 15.0 10.00 0 L 35.0 REF. 20.0 90.0 REF. Ø 6F7 (2) HOLES Ø 9.0 (2) HOLES SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR075M APR076M MATERIAL Steel / ASTM A-36 SS type 303 or 304 ©1997 Auto/Steel Partnership www.naamsstandards.org WT. kg 0.63 0.63 C A B This document is Uncontrolled when printed. I – 45 LOCATING PIN RETAINER (FULL METRIC) 20 mm SERIES APR314M, 315M, 316M, 317M TM Assembly 04/22/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURACES TO BE FLAT, PARALLEL & PERPENDICULAR TO O L WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. +0.015 NO BLACK OXIDE FINISH -0.00 Ø16.00 TO "SS TYPE" COMPONENTS. D IS C O N TI N U ED D 12.50 O L X X X 25 25.00 25..0 00 0 R REF. RE EF. F. 10 10.00 10..0 00 0 O L +0.03 -0.00 12.50 Ø 6 F7 (2) HOLES O L 1.0 x 45° 5 5°° C A 40.0 40 40..0 0 35.0 35 35..0 0 30.000 49.0 49 49..0 0 REF. R RE EF. F. 15.00 O L 5.0 35.0 25.000 13.0 15.0 9.0 48.0 REF. NAAMS CODE A APR314M M8 x 1.25 APR315M APR316M M8 x 1.25 9.0 APR317M 9.0 ©1997 Auto/Steel Partnership WT. kg MATERIAL STEEL / ASTM A-36 SS type 303 or 304 STEEL / ASTM A-36 SS type 303 or 304 www.naamsstandards.org 0.34 0.34 0.34 SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART B A 0.34 This document is Uncontrolled when printed. I-46 LOCATING PIN RETAINER (FULL METRIC) 20 mm SERIES APR336M, 337M, 338M, 339M TM Assembly 02/12/14 Tolerances: Ø16.00 +0.015 -0.00 12.50 O L X X X 25.00 REF. 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURACES TO BE FLAT, PARALLEL & PERPENDICULAR TO O L WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS C 10.00 O L +0.03 -0.00 12.50 O L 1.0 x 45° A (2) HOLES Ø 6 F7 (2) HOLES 55.0 50.0 45.00 30.000 64.0 REF. 20.0 15.00 O L 35.0 13.0 15.0 25.000 9.0 48.0 REF. NAAMS CODE A APR336M M8 x 1.25 APR337M APR338M M8 x 1.25 9.0 APR339M 9.0 ©1997 Auto/Steel Partnership WT. kg MATERIAL STEEL / ASTM A-36 SS type 303 or 304 STEEL / ASTM A-36 SS type 303 or 304 www.naamsstandards.org 0.37 0.37 0.37 SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART 0.37 This document is Uncontrolled when printed. I-47 B A LOCATING PIN RETAINER (FULL METRIC) 20 mm SERIES APR057M, 058M TM Assembly 04/22/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURACES TO BE FLAT, PARALLEL & PERPENDICULAR TOO L WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO "SS TYPE" COMPONENTS. +0.03 -0.00 D IS C O N TI N U ED Ø16.00 +0.015 -0.00 D 10.00 12.50 O L X X X 25 25.00 REF. 55.00 66.0 12.50 C 1.0 x 4 45° 45 5°° 9.0 15.00 30.000 O L 15.0 10 10.00 10..0 00 0 O L 35 35.0 35..0 0 REF. R RE EF. F. 20.0 75.0 REF. Ø6 F7 (2) HOLES Ø 9.0 SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR057M APR058M MATERIAL STEEL / ASTM A-36 SS type 303 or 304 ©1997 Auto/Steel Partnership www.naamsstandards.org WT. kg B A 0.41 0.41 This document is Uncontrolled when printed. I-48 LOCATING PIN RETAINER (FULL METRIC) 20 mm SERIES APR085M, 086M, 087M, 088M TM Assembly 04/22/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURACES TO BE FLAT, PARALLEL & PERPENDICULAR TOO L WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO "SS TYPE" COMPONENTS. +0.03 -0.00 D IS C O N TI N U ED +0.015 -0.00 D Ø16.00 10.00 Ø6 F7 (2) HOLES 12..5 5 12 12.5 X X X O L 25.00 REF. C A 9.0 00 00 15.00 30.000 30 30. .0 00 00 0 55.00 66.0 12.5 O L 1.0 x 45° 30.0 35.00 25.0 O L 75.0 REF. SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE MATERIAL A APR085M M8 x 1.25 APR086M APR087M M8 x 1.25 DRILL & C/BORE FOR M8 SHCS APR088M DRILL & C/BORE FOR M8 SHCS ©1997 Auto/Steel Partnership www.naamsstandards.org STEEL / ASTM A-36 SS type 303 or 304 STEEL / ASTM A-36 SS type 303 or 304 WT. kg 0.40 B 0.40 0.40 A 0.40 This document is Uncontrolled when printed. I-49 LOCATING PIN RETAINER (FULL METRIC) 20 mm SERIES APR077M, 078M TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURACES TO BE FLAT, PARALLEL & PERPENDICULAR TOO L WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS Ø16.00 +0.015 -0.00 10.00 C +0.03 -0.00 12.50 O L X X X 25.00 REF. 12.50 9.0 15.00 1.0 x 45° 30.000 45.00 81.0 70.00 O L 15.0 10.00 O L 35.0 REF. 20.0 90.0 REF. Ø 6 F7 (2) HOLES Ø 9.0 (2) HOLES SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR077M APR078M MATERIAL STEEL / ASTM A-36 SS type 303 or 304 ©1997 Auto/Steel Partnership www.naamsstandards.org WT. kg B 0.52 0.52 This document is Uncontrolled when printed. A I-50 LOCATING PIN RETAINER G L O B A L S TA N D A R D C O M P O N E N T S (FULL METRIC) 20 mm SERIES APR250M THRU APR253M TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS A +0.015 -0.00 Ø 16.00 15.00 0 L X X X 30.00 REF. 0 L 1.0 x 45° 40.0 35.0 10.00 +0.03 -0.00 15.00 Ø 8F7 (2) HOLES 0 L A 30.000 49.0 REF. 15.00 0 L 5.0 35.0 25.000 15.0 13.0 9.0 48.0 REF. NAAMS CODE APR250M APR251M APR252M APR253M A M8 x 1.25 M8 x 1.25 9.0 9.0 ©1997 Auto/Steel Partnership MATERIAL Steel / ASTM A-36 SS type 303 or 304 Steel / ASTM A-36 SS type 303 or 304 www.naamsstandards.org WT. kg 0.41 0.41 0.41 0.41 SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART This document is Uncontrolled when printed. I – 51 LOCATING PIN RETAINER G L O B A L S TA N D A R D C O M P O N E N T S (FULL METRIC) 20 mm SERIES APR255M, APR256M TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS A +0.015 -0.00 Ø 16.00 25.0 REF. 40.0 35.0 0 L 12.5 1.0 x 45° 12.5 0 L 0 L 10.00 +0.03 -0.00 XXX M8 x 1.25 30.000 49.0 REF. 15.00 0 L 35.00 15.0 13.0 5.0 48.0 REF. 9.0 Ø 8F7 (2) HOLES SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR255M APR256M MATERIAL Steel / ASTM A-36 SS type 303 or 304 ©1997 Auto/Steel Partnership www.naamsstandards.org WT. kg 0.41 0.41 This document is Uncontrolled when printed. I – 52 LOCATING PIN RETAINER G L O B A L S TA N D A R D C O M P O N E N T S (FULL METRIC) 20 mm SERIES APR201M THRU APR204M Ø16.00 TM Assembly Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS +0.015 -0.00 15.00 0 L 02/12/14 X X X 30.00 REF. 10.00 0 L +0.03 -0.00 15.00 A (2) HOLES 1.0 x 45° Ø 8F7 (2) HOLES 55.0 50.0 45.00 64.0 REF. 30.000 20.0 15.00 0 L 35.0 25.000 13.0 15.0 9.0 48.0 REF. NAAMS CODE APR201M APR202M APR203M APR204M A M8 x 1.25 M8 x 1.25 9.0 9.0 ©1997 Auto/Steel Partnership MATERIAL Steel / ASTM A-36 SS type 303 or 304 Steel / ASTM A-36 SS type 303 or 304 www.naamsstandards.org WT. kg 0.45 0.45 0.45 0.45 SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART This document is Uncontrolled when printed. I – 53 A LOCATING PIN RETAINER (FULL METRIC) 20 mm SERIES APR211M THRU APR212M G L O B A L S TA N D A R D C O M P O N E N T S TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS Ø16.00 A +0.015 -0.00 25.0 REF. 1.0 x 45° 55.0 50.0 64.0 REF. 0 L M8 x 1.25 (2) HOLES 12.5 12.5 0 L 0 L 10.00 +0.03 -0.00 XXX 45.00 30.000 20.0 15.00 Ø 8F7 (2) HOLES 48.0 REF. NAAMS CODE APR211M APR212M MATERIAL Steel / ASTM A-36 SS type 303 or 304 ©1997 Auto/Steel Partnership www.naamsstandards.org 9.0 35.00 15.0 13.0 0 L WT. kg 0.32 0.32 SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART This document is Uncontrolled when printed. I – 54 LOCATING PIN RETAINER G L O B A L S TA N D A R D C O M P O N E N T S (FULL METRIC) 20 mm SERIES APR260M, APR261M TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS +0.015 -0.00 Ø16.00 A +0.03 -0.00 10.00 15.00 0 L X X X 30.00 REF. 55.00 9.0 15.00 1.0 x 45° 0 L 30.000 66.0 15.00 15.0 10.00 0 L 35.0 REF. 20.0 75.0 REF. Ø 8F7 (2) HOLES Ø 9.0 SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR260M APR261M MATERIAL Steel / ASTM A-36 SS type 303 or 304 ©1997 Auto/Steel Partnership www.naamsstandards.org WT. kg 0.50 0.50 This document is Uncontrolled when printed. I – 55 LOCATING PIN RETAINER G L O B A L S TA N D A R D C O M P O N E N T S (FULL METRIC) 20 mm SERIES APR265M THRU APR268M TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS +0.015 -0.00 +0.03 -0.00 Ø16.00 10.00 A Ø 8F7 (2) HOLES 15.0 0 L X X X 30.0 REF. 0 L 9.0 15.00 30.000 55.00 66.0 15.0 A 1.0 x 45° 30.0 35.00 25.0 0 L 75.0 REF. SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR265M APR266M APR267M APR268M A M8 x 1.25 M8 x 1.25 Drill & C/Bore for M8 SHCS Drill & C/Bore for M8 SHCS ©1997 Auto/Steel Partnership www.naamsstandards.org MATERIAL Steel / ASTM A-36 SS type 303 or 304 Steel / ASTM A-36 SS type 303 or 304 WT. kg 0.50 0.50 0.50 0.50 This document is Uncontrolled when printed. I – 56 LOCATING PIN RETAINER (FULL METRIC) 20 mm SERIES APR221M, APR222M G L O B A L S TA N D A R D C O M P O N E N T S TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURFACES TO BE FLAT, PARALLEL & PERPENDICULAR TO OL WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS +0.015 -0.00 A +0.03 -0.00 Ø16.00 10.00 15.00 0 L X X X 30.00 REF. 15.00 30.000 45.00 1.0 x 45° 9.0 0 L 70.00 81.0 15.00 15.0 10.00 0 L 35.0 REF. 20.0 90.0 REF. Ø 8F7 (2) HOLES Ø 9.0 (2) HOLES SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR221M APR222M MATERIAL Steel / ASTM A-36 SS type 303 or 304 ©1997 Auto/Steel Partnership www.naamsstandards.org WT. kg 0.63 0.63 This document is Uncontrolled when printed. I – 57 LOCATING PIN RETAINER (FULL METRIC) 20 mm SERIES APR271M THRU APR274M TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURACES TO BE FLAT, PARALLEL & PERPENDICULAR TO O L WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS Ø16.00 A +0.015 -0.00 12.50 O L X X X 25.00 REF. 10.00 O L +0.03 -0.00 12.50 Ø 8 F7 (2) HOLES O L 1.0 x 45° A 40.0 35.0 30.000 49.0 REF. 15.00 O L 5.0 35.0 25.000 13.0 15.0 9.0 48.0 REF. NAAMS CODE A APR271M M8 x 1.25 APR272M APR273M M8 x 1.25 9.0 APR274M 9.0 ©1997 Auto/Steel Partnership WT. kg MATERIAL STEEL / ASTM A-36 SS type 303 or 304 STEEL / ASTM A-36 SS type 303 or 304 www.naamsstandards.org 0.34 0.34 0.34 SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART 0.34 This document is Uncontrolled when printed. I-58 LOCATING PIN RETAINER (FULL METRIC) 20 mm SERIES APR231M THRU APR234M TM Assembly 02/12/14 Tolerances: Ø16.00 +0.015 -0.00 12.50 O L X X X 25.00 REF. 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURACES TO BE FLAT, PARALLEL & PERPENDICULAR TO O L WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS 10.00 O L +0.03 -0.00 12.50 O L 1.0 x 45° A (2) HOLES Ø 8 F7 (2) HOLES 55.0 50.0 45.00 30.000 64.0 REF. 20.0 15.00 O L 35.0 13.0 15.0 25.000 9.0 48.0 REF. NAAMS CODE A APR231M M8 x 1.25 APR232M APR233M M8 x 1.25 9.0 APR234M 9.0 ©1997 Auto/Steel Partnership WT. kg MATERIAL STEEL / ASTM A-36 SS type 303 or 304 STEEL / ASTM A-36 SS type 303 or 304 www.naamsstandards.org 0.37 0.37 0.37 SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART 0.37 This document is Uncontrolled when printed. I-59 A LOCATING PIN RETAINER (FULL METRIC) 20 mm SERIES APR276M, APR277M TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURACES TO BE FLAT, PARALLEL & PERPENDICULAR TOO L WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS Ø16.00 +0.015 -0.00 10.00 A +0.03 -0.00 12.50 O L X X X 25.00 REF. 55.00 66.0 12.50 1.0 x 45° 9.0 15.00 30.000 O L 15.0 10.00 O L 35.0 REF. 20.0 75.0 REF. Ø8 F7 (2) HOLES Ø 9.0 SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR276M APR277M MATERIAL STEEL / ASTM A-36 SS type 303 or 304 ©1997 Auto/Steel Partnership www.naamsstandards.org WT. kg 0.41 0.41 This document is Uncontrolled when printed. I-60 LOCATING PIN RETAINER (FULL METRIC) 20 mm SERIES APR280M THRU APR283M TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURACES TO BE FLAT, PARALLEL & PERPENDICULAR TOO L WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS Ø16.00 +0.015 -0.00 10.00 +0.03 -0.00 Ø8 F7 A (2) HOLES 12.5 X X X O L 25.00 REF. A 9.0 15.00 30.000 55.00 66.0 12.5 O L 1.0 x 45° 30.0 35.00 25.0 O L 75.0 REF. SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE MATERIAL A APR280M M8 x 1.25 APR281M APR282M M8 x 1.25 DRILL & C/BORE FOR M8 SHCS APR283M DRILL & C/BORE FOR M8 SHCS ©1997 Auto/Steel Partnership www.naamsstandards.org STEEL / ASTM A-36 SS type 303 or 304 STEEL / ASTM A-36 SS type 303 or 304 WT. kg 0.40 0.40 0.40 0.40 This document is Uncontrolled when printed. I-61 LOCATING PIN RETAINER (FULL METRIC) 20 mm SERIES APR241M, APR242M TM Assembly 02/12/14 Tolerances: 1 PLACE ± 0.3 2 PLACE ± 0.03 3 PLACE ± 0.020 SURACES TO BE FLAT, PARALLEL & PERPENDICULAR TOO L WITHIN 0.015 T.I.R. NOTES: IDENTIFY WITH NAAMS CODE NUMBER AS SHOWN XXX. BLACK OXIDE FINISH. NO BLACK OXIDE FINISH TO “SS TYPE” COMPONENTS Ø16.00 +0.015 -0.00 10.00 A +0.03 -0.00 12.50 O L X X X 25.00 REF. 12.50 9.0 15.00 1.0 x 45° 30.000 45.00 81.0 70.00 O L 15.0 10.00 O L 35.0 REF. 20.0 90.0 REF. Ø 8 F7 (2) HOLES Ø 9.0 (2) HOLES SEE PAGE B-1.1 FOR GLOBAL MATERIALS CHART NAAMS CODE APR241M APR242M MATERIAL STEEL / ASTM A-36 SS type 303 or 304 ©1997 Auto/Steel Partnership www.naamsstandards.org WT. kg 0.52 0.52 This document is Uncontrolled when printed. I-62
Similar documents
BASES INDEX - The NAAMS Global Standard Components
SCRIBE CENTERLINE OF ROBOT ON SUB-DETAIL “A” (ALL FOUR SIDES)
SEE FOLLOWING PAGE FOR NAAMS CODE, “A” AND “B” DIMENSIONS.
(A) 1 REQ’D ~ STL. PLATE ASTM A-36 ~ 1-3/4” X 1000mm X 1000mm
(B) 1 REQ’D ~ ...
SHIMS AND SPACERS - The NAAMS Global Standard Components
ASH102N–ASH120N Metric Fitting Shims 1-Slot (20 mm)
ROBOTICS - The NAAMS Global Standard Components
CAD STARTER MODEL ONLY - DO NOT ORDER AS NAAMS NUMBER - ASSIGN A CUSTOM NUMBER
©1997 Auto/Steel Partnership
RISER ANGLE BRACKETS - The NAAMS Global Standard
©1997 Auto/Steel Partnership www.naamsstandards.org
This document is Uncontrolled when printed.
FASTENER COMPONENTS INDEX - The NAAMS Global Standard
for certain deviations in the parts being fastened, such as hole straightness, angularity between the axis of the
tapped hole and that of the hole for the shank, differences in the center distances...