Quick User Guide

Q
30
Quick User Guide
For your ease and convenience, this guide is intended to find the most essential
functions you will need to start experiencing your Infiniti Q30.
Cockpit overview
Instrument panel
Meters & gauges
Doors Unlocking & Locking
Intelligent Key System
Anti-theft Alarm System
Front Seat and Head Restraint Adjustment
Automatic Drive Positioner System
Automatic Front Passenger Front Air Bag
Deactivation
Headlight Switch
Combination Switch
High Beam Assist (where fitted)
Ignition Switch Positions
Instrument Brightness Control
Clock Settings
Power Windows and Outside Mirrors
Sunshade Operation
Automatic Anti-dazzle Rearview Mirror
Steering Wheel Controls (left hand side)
2
4
6
8
8
8
9
9
10
10
11
11
12
12
12
13
13
13
14
Steering Wheel Controls (right hand side)
Vehicle Information Display
Centre Multifunction Control Panel
Automatic Transmission Operation
Tyre Pressure Monitoring System
Audio System
Bluetooth Streaming Audio
Connecting your Mobile Phone via Bluetooth
Auxiliary Inputs
Navigation System
Climate Control
Electronic Parking Sensor System
Rear/Around View Monitor
Intelligent Park Assist
Cruise Control and Speed Limiter Systems
Hill Start Assist
Driver Assistance Systems
Fuel Filling
Bonnet Opening
14
15
16
17
18
19
19
20
20
20
21
23
23
24
24
26
26
28
28
It is important to note that this guide does not replace the full Owner's Manual, which should be referred to for complete details, security items and warnings.
1
Cockpit overview
2
Cockpit overview
Electric parking brake switch
Light switch
Cruise control/speed limiter switch
Vehicle information & menu control switches
Combined Turn signal/Low-High beam/Wiper & washer switch
Shift paddles
Audio & Telephone control switches
3
Instrument panel
4
Instrument panel
Ignition switch
Multi-function control touch screen/Rear view monitor display/
Around view monitor display
Audio system
Centre console switches
- Seat Heating (where fitted)
- Hazard light switch
- Engine Stop/Start system ON/OFF switch
- Electronic Parking Sensor OFF switch
Climate control panel
- Heater & Air conditioning
- Front/Rear window defogger
Drive mode selection
INFINITI multi-function controller
5
Meters & gauges
6
Meters & gauges
Speedometer
Fuel gauge
Vehicle Information Display
Upper Display
Tachometer
Engine coolant temperature gauge
7
Doors Unlocking & Locking
Anti-theft Alarm System
An audible and visible alarm is triggered when a door, the tailgate or bonnet is
opened when the system is armed.
You can lock and unlock the doors and tailgate by pressing the lock
or unlock
button on the Intelligent Key. For emergency purposes, a
mechanical key is integrated in the Intelligent Key. To release the mechanical
key, shift the knob
and pull out the key.
Intelligent Key System
The Intelligent Key System is a keyless entry system that allows you to lock
and unlock the doors and tailgate without using the key when the Intelligent
Key is within the system’s operating range
. To open a door, touch the
inside of the door handle
and pull the handle to open the door. To lock the
doors, touch the sensor
on the door handle.
The system will automatically be armed
after the vehicle is locked. Indicator lamp
will flash, indicating thet the alarm
system is armed. The alarm system is
operational after approx. 15 seconds. The
alarm is disarmed when the vehicle is
unlocked.
Optionally, your vehicle may be equipped with tow-away protection which
additionally triggers the alarm when the system is armed and the vehicle’s
inclination angle changes. Also, an interior motion sensor may be fitted
to your vehicle that triggers the alarm when motion is detected within the
passenger compartment.
The tow-away protection and interior
motion sensors can be switched off
using the switches above the interior
rear-view mirror. To exclude the tow
away or interior motion sensors from
the alarm system:
1. Switch off the engine.
2. Press switch
(deactivation of interior motion sensor) or
(deactivation of tow-away sensor).
The indicator light will flash/illuminate to confirm deactivation of the
respective function(s).
3. Lock the vehicle.
8
Front Seat and Head Restraint Adjustment
HEAD RESTRAINT ADJUSTMENT
FRONT SEAT MANUAL SEAT ADJUSTMENT
Pull handle to adjust seat in horizontal direction
Turn knob to adjust angle of front of seat
Pull/Push lever to raise/lower the seat
Turn knob to adjust seatback angle
Push buttons to adjust seatback contour
FRONT SEAT POWER SEAT ADJUSTMENT
Move switch to adjust seat in horizontal
direction
Move switch to adjust seatback angle
Move either front or rear side of switch to
adjust angle of seat or raise/lower the seat
Push buttons to adjust seatback contour
Push knob
and raise/lower the head
restraint until it reaches the desired position.
After adjustment, make sure the lock knob is
engaged in one of the notches.
Automatic Drive Positioner System
You can store up to three different seat and
outside mirror positions using the automatic
drive positioner system.
To store a setting:
1. Adjust the seat
2. Adjust the outside mirrors
3. Briefly press the memory button
, then press and hold preset
position 1, 2 or 3
within three seconds. A tone sounds when the
setting is stored in the memory.
To call up a stored setting, press the desired preset button.
Steering Wheel Adjustment
Push down the lock lever
wheel as desired.
and adjust the steering
After adjustment, make sure to firmly push the lock
lever back into position to lock the steering wheel in
place.
9
Automatic Front Passenger Front Air Bag
Deactivation
Headlight Switch
The automatic front passenger front air bag deactivation system analyses the
weight of the person seated on the front passenger seat.
Depending on the analysis, the front-passenger front air bag is either enabled
or disabled.
If a rearward-facing child restraint system
is fitted to the front passenger seat, the
<PASSENGER AIR BAG OFF> indicator light
must illuminate after the system
self-test and remains illuminated.
The front passenger front air bag then
is deactivated. The system does not
deactivate front passenger side and curtain air bags.
The headlight switch has following positions:
Left hand parking lights switched on.
Electric Parking Brake
To apply the parking brake, push the electric
parking brake handle
, regardless of the
ignition switch position.
To release the parking brake, pull the
electric parking brake handle while the
ignition is ON.
On models with automatic transmission, the
electric parking brake will be automatically
released when you depress the accelerator
pedal to drive away.
Right hand parking lights switched on.
Side lights, license plate lights and combination meter lighting
switched on.
Automatic headlight mode: headlights switch on/off automatically,
depending on ambient light conditions/daytime light system switched on.
Dipped beam/high beam headlights.
Selection between dipped beam and high beam is done by using the
combination switch (refer to page 11).
Rear fog light switch.
Front fog light switch.
10
Combination Switch
The combination switch is located above the cruise control switch and
provides multiple functions as described below.
Push the combination
switch away from you
while the headlight switch
is in the <AUTO> or
position to select high
beam.
Pull the switch towards you to flash the high beam headlights.
Push the switch up or down to activate the right/left turn signal light.
High Beam Assist (where fitted)
The High Beam Assist system automatically switches
from high beam to low beam when the headlight
switch is in the <AUTO> position while high beam
is selected and an oncoming or leading vehicle is
detected. When the vehicle is no longer detected, low
beam will be switched back to high beam. The high
beam assist indicator light
in the instrument panel illuminates when the
system is active.
The high beam assist system will not function at speeds below approximately
40 km/h.
WINDSHIELD WIPERS AND WASHER
Press to operate windshield washer & wipers.
Turn switch to select:
Automatic wipe, low rain
sensor sensitivity.
Automatic wipe, high rain
sensor sensitivity.
Continuous wipe, slow.
Continuous wipe, fast.
REAR WINDOW WIPER AND WASHER
Turn switch to select:
Wipes with washer
fluid, then returns
to intermittent
wiping.
Intermittent wiping
Off
Wipes with washer
fluid
11
Ignition Switch Positions
Instrument Brightness Control
The ignition switch has following
positions:
A light sensor in the instrument cluster automatically controls the brightness
of the instrument panel illumination. In daylight, the instrument panel is not
illuminated.
OFF position. After opening the
door, the steering wheel will
be locked. No power supply to
consumers.
The brightness of the instrument panel
illumination can be adjusted using the
instrument brightness control knob
.
ACC position - power supply to
several consumers like window
wipers.
ON position - power supply to all consumers. For diesel models: glow
plugs start pre-heating the engine at low engine temperatures.
START position: operates the starter motor to start the engine.
Clock Settings
Clock settings can be changed as
follows:
1. Push <Menu> button on
INFINITI controller
2. Touch [SETTINGS]
3. Select item to adjust:
- On-screen clock on/off
- Summer time
- Clock format [12h/24h]
- Time zone
- Clock offset adjustment
12
Power Windows and Outside Mirrors
MAIN SWITCH OPERATION
All power windows and the outside mirrors can be operated through the main
switch on the driver’s door.
Power windows OPEN/CLOSE.
Sunshade Operation
The sunshade operates only when the ignition is switched ON.
To open or close the sunshade, press and hold
the OPEN
or CLOSE
side of the switch and
release it when the sunshade has reached the
desired position.
Disable rear passenger window
operation by rear passengers.
Select left hand (L) / right hand
(R) outside mirror.
Adjust outside mirror.
Fold/unfold outside mirror.
POWER WINDOW CONvENIENCE
OPENINg/CLOSINg FEATURE
The vehicle can be locked/unlocked and the power windows be closed/
opened simultaneously from outside the vehicle using the Intelligent Key as
follows:
To lock the vehicle and close the
power windows simultaneously,
on
touch the sensor surface
the door handle until the side
windows are fully closed.
To fully open or close the sunshade automatically, briefly press the OPEN
or CLOSE
side of the switch and release it. To stop the movement of the
sunshade during automatic opening/closing, press either side of the switch.
Automatic Anti-dazzle Rearview Mirror
The interior rear-view mirror
(and the exterior mirror on the
driver’s side) automatically
switch to anti-dazzle mode if
the ignition is switched on and
light from a tracing vehicle
strikes the sensor
in the
rear-view mirror.
The anti-dazzle mode is not activated if reverse gear is engaged or if the
interior lighting is switched on.
To unlock the vehicle and open the
windows simultaneously, press and hold the button on the Intelligent Key
until the side windows have reached the desired position.
13
Steering Wheel Controls (left hand side)
LEFT/RIGHT arrow
buttons: call up and
navigate through
menu bar on vehicle
information display.
UP/DOWN arrow
buttons: navigate
within menus on
vehicle information
display.
<OK> button: to confirm
a selection.
BACK button: to return to the previous screen.
Steering Wheel Controls (right hand side)
Voice command
button: press to start
voice recognition
system. To cancel
voice recognition
session, say "Exit" or
push and hold button
for 5 seconds.
Volume up (+)/down
(-) button: press to
adjust volume of
audio/telephone.
Mute button: press to
mute sound.
Telephone 'reject' button: press to end a phone call or reject an
incoming call.
Telephone 'answer' button: press to select telephone menu/start a
phone call.
14
vehicle Information Display
Depending on vehicle specifications, following menus can be selected:
•
•
•
•
•
•
[Trip] - Trip computer data
[Navi] - Navigation instructions
[Audio] - Audio settings
[Tel] - Telephone service status
[Assist] - Driver Assistance settings
[Serv] - Service settings
Use the and buttons on the steering wheel to navigate within the menus,
use the <OK> button to confirm a selection and/or save a setting.
Use the BACK button
to return to a previous screen or exit a menu.
The vehicle information display is located centrally between the tachometer
and speedometer and displays following information:
Outside temperature or speed.
Time.
Text/data field.
Menu bar.
Selected drive programme.
Transmission position (automatic transmission models).
Engine Stop/Start system status indicator.
, press the left or right arrow button on the
To call up the menu bar
steering wheel. The menu bar will disappear after a few seconds of inactivity.
The Text/data field displays the selected menu, submenus, display messages,
system settings and trip computer data.
15
Centre Multifunction Control Panel
USINg THE INFINITI CONTROLLER
Models with navigation system:
Push <MAP/VOICE> to display
the vehicle’s current location,
push again to display the Display
View Bar and display views. Push
and hold to repeat the last route
guidance instruction.
The centre multifunction control panel in the centre console can be operated
through touching/swiping the screen or by using the INFINITI controller.
Following menus can be selected:
•
•
•
•
•
Navigation (where fitted)
Phone
Apps
Information
Settings
Models without navigation system:
to display the hands-free
Push
phone screen.
Push the button to display the
main menu.
Push the
knob to select the
shortcut menu or enter a selection. Push the arrow buttons to scroll
through menu items. Turn the knob to zoom in/out on a map.
Push the BACK
button to go back to the previous screen.
Push
to display the audio screen. When
is pushed when the
audio screen is already displayed, the source list will be displayed.
Models with around view monitor:
Push
to display the around view monitor screen. The camera
view can only be displayed when the ignition is switched ON.
Models without around view monitor: push
to adjust display
brightness, push and hold to turn the display on/off.
16
Automatic Transmission Operation
The automatic transmission is designed so that
the footbrake MUST be depressed before shifting
from P (Park) to any drive position while the
ignition is ON.
Use the Park position when the vehicle is parked.
Always make sure that the vehicle is completely
stopped before pressing the Park (P) button
.
program (E or S) as soon as the driving situation permits.
to permanently select the manual drive
Use the program selector button
program.
Engine Stop/Start System
The engine Stop/Start system automatically stops and restarts the engine
when the vehicle is stationary. This system contributes to improving fuel
economy and exhaust emissions.
DRIvE PROgRAM SELECTION
allows you to choose between three drive
The program selector button
programmes with different driving characteristics:
in the Stop/Start system ON/
If the system is turned on, the indicator light
OFF switch (see next page) illuminates. Also, the Stop/Start system indicator
is displayed in the lower part of the vehicle information display. If the Stop/
Start system indicator in the vehicle information display lights up in yellow, this
indicates that the system is temporarily not available, due to certain conditions
not being met at that moment. When all conditions for the Stop/Start system's
functioning are met and the system is thus operational, the Stop/Start system
indicator in the vehicle information display illuminates in green.
E
Economy: for comfortable and economic driving.
The Stop/Start system will stop the engine under following conditions:
S
Sport: for sporty driving style.
M
Manual: for manual gear shifting.
If you switch the ignition off with the transmission
in D (Drive) or R (Reverse), the transmission
automatically shifts into N (Neutral).
When pressing the program selector button, the selected drive program
(E, S or M) is displayed in the vehicle information display
.
•
On manual transmission models, bring the vehicle to a complete
stop, remain at idle in Neutral gear and release the clutch pedal.
• On automatic transmission models, bring the vehicle to a complete
stop.
The Stop/Start system will restart the engine under following conditions:
For manual gear shifting in the manual drive program M, use
the shift paddles behind the steering wheel to change gears.
•
Left hand paddle: shift down.
•
Right hand paddle: shift up.
When using the shift paddles while the Economy (E) or Sport
(S) drive program is selected, the transmission will shift into the Manual drive
program for a limited time and will return to the previously selected drive
On manual transmission models, the engine will restart when you
depress the clutch pedal to shift into a (forward or reverse) gear and
depress the accelerator pedal.
On automatic transmission models, the engine will restart when you
take your foot off the brake pedal and depress the accelerator pedal.
Note: The Stop/Start system will not function under certain conditions, for example
when the engine has not yet reached its normal operating temperature. This is normal
behaviour and does not indicate a system fault.
17
SWITCHINg OFF THE STOP/START SySTEM
The Stop/Start system can be switched off for the
duration of a journey by pressing the Stop/Start
system switch; the indicator light in the switch
will turn off and the Stop/Start system indicator in
the vehicle information display will turn off. Next
time you switch the ignition to ON, the system will
automatically be reactivated.
To manually reactivate the stop/start system, press the Stop/Start switch
again; the indicator light
in the switch will illuminate and the Stop/Start
system indicator will be displayed in the vehicle information display.
RESTARTINg TPMS
The TPMS system needs to be restarted in the following cases:
•
•
•
After the pressure of the tyre(s) has been adjusted
When a tyre or wheel has been replaced
When the position of tyres has been changed.
The TPMS system can be restarted through the Service [Serv.] menu in the
vehicle information display.
For full details on the restarting procedure, refer to your vehicle’s Owner’s
Manual.
Tyre Pressure Monitoring System
The Tyre Pressure Monitoring System (TPMS)
continuously monitors the pressure of the road
wheels against the set target pressures. If the
pressure of one or more tyres significantly
deviates from the target value, the Tyre Pressure
Monitoring System will provide a warning on the
vehicle information display and the TPMS warning
light
in the combination meter will illuminate.
If the message is displayed on the vehicle information display and the TPMS
warning light illuminates, check and adjust the pressure of the tyres at the
earliest opportunity.
The Tyre Pressure Monitoring System will not activate until the vehicle has
driven at a speed above 25 km/h.
18
Audio System
When DAB (if equipped) is playing, pushing this button will change the
station within the ensemble.
Preset station buttons: Six preferred stations in the preset list for each
radio band can be stored.
<VOL/ > Push to switch the audio system on/off, turn to adjust
volume.
Bluetooth Streaming Audio
If you have a compatible Bluetooth device with streaming audio (A2DP profile),
you can set up a wireless connection between your Bluetooth device and the
in-vehicle audio system, enabling you to listen to the audio files stored on
your device through the vehicle’s audio system.
<SEEK.TRACK> In DAB (Digital Audio Broadcasting) mode (where fitted):
seeks the previous/next available DAB ensemble.
In FM/AM mode: increases/decreases the radio frequency
automatically until next station is found.
In CD mode or when an external device is connected: fast forward/
rewind through tracks.
To set up the wireless connection between your audio device and the
in-vehicle audio system:
Push to eject a CD.
<RADIO> Push to switch to radio mode or to switch between AM, FM and
DAB (Digital Audio Broadcast, if equipped).
<STATUS> Push to display the audio status screen.
<MEDIA> Push to select the desired audio source (CD, iPod, USB,
Bluetooth Streaming Audio or AUX).
<TUNE.FOLDER> Push or hold to manually tune into a station in AM/FM
radio mode. Push to select MP3/WMA/AAC folders on an externally
connected device.
1.
2.
3.
4.
5.
Push the <MENU> button
on the INFINITI controller.
Touch [Settings] on the display.
Touch [Bluetooth Settings] and [Pair Device] .
Touch [Add New Device].
When a PIN code appears on the screen, operate the Bluetooth device
to enter/confirm the PIN code.
19
Connecting your Mobile Phone via
Bluetooth
Using Bluetooth technology, you can connect (pair) your mobile phone with
the in-vehicle system for hands-free use of your mobile phone.
To pair your mobile phone with the in-vehicle system, follow the same
procedure as described under Bluetooth Streaming Audio on the previous
page.
Navigation System
Your vehicle may be equipped with a Navigation system which operation is
described in detail in the separate Navigation System Owner’s Manual.
As an example, the basic procedure to enter a destination is described below.
SETTINg A DESTINATION
To set a destination for navigation, use the INFINITI controller and/or the multifunction control touch screen.
Auxiliary Inputs
Your vehicle is equipped with two USB ports,
located in the centre console, to which you can
connect compatible devices (mobile phones,
iPods, other compatible audio devices, USB
memory sticks, etc.).
After connecting your device through one of
the USB ports, push the <MEDIA> button on the
audio unit to select audio playback from the device connected through the
USP port.
Note: when two iPhones are connected to both of the USB ports, the system recognizes
only one of the connected iPhones at a time. The second iPhone will charge only.
Street Address
-----------
Delete
Country
Postcode
1
2
Q
3
W
A
4
E
S
Z
Change
5
R
D
X
6
T
F
C
Space
7
Y
G
V
UNITED KINGDOM
8
U
H
B
9
I
J
N
Last 5 Cities
0
P
O
L
K
M
‘
&
_
List
1. Push the <MENU> button
on the INFINITI controller.
2. Select [Navigation] from the menu and then [Street Address]
3. The [Street Address] screen will be displayed. Now you can select your
destination by inputting postal code or city name, followed by the
street address.
20
4. Select the city of the destination from the list.
5. Enter the name of the street and touch [List]. A list screen is displayed.
Select the street of the destination from the list.
6. Enter the house number and touch [OK]
7. The selected destination is
displayed at the centre of the
map.
Touch [OK] to confirm the
displayed location as your
destination.
Climate Control
MANUAL CLIMATE CONTROL SySTEM
26
0
28
MAX
1
24
2
22
3
4
20
8. The entire route is displayed
on the screen. Touch [Start] to
start route guidance.
REAR
Calculate Route
18
16
A/C
6
5
Start
More Routes
Route Info
Add Waypoint
Move Loc.
Temperature control dial
Windscreen defogger MAX switch
Air distribution selection switches
Air recirculation switch
Fan speed control dial
Air conditioning on/off switch
Rear window defogger switch
21
THERMOTRONIC AUTOMATIC CLIMATE CONTROL SySTEM
Rear window defogger switch
Zone (dual mode) switch for separate temperature control driver/
passenger zone.
DEFROSTINg/DEFOggINg THE WINDSCREEN
For maximum defrosting/defogging performance, switch on the air
conditioning by pressing the <A/C> switch, then push the windscreen defogger
MAX switch
. The indicator light in the switches will illuminate.
The climate control system now switches to the following functions:
•
•
•
•
Temperature control dial (driver side)
Automatic climate control mode switch
Windscreen defogger MAX switch
Fan speed control switch to increase airflow
Air distribution selection switches
High airflow.
High temperature.
Air distribution to the windscreen and side windows.
Air recirculation mode is switched off.
After the windows are defogged, press the windscreen defogger MAX button
again.
The indicator light in the switch will turn off and the previous settings are
restored. The air recirculation mode remains deactivated.
You can also switch off the defogger MAX function by turning the temperature
control dial.
Air recirculation switch
Temperature control dial (passenger side)
Climate control system ON/OFF switch
Residual heat function switch (used to continue interior heating after
engine is switched off).
Air conditioning on/off switch
Fan speed control switch to decrease airflow
22
Electronic Parking Sensor System
Rear/Around view Monitor
The electronic parking sensor system is a parking aid which uses ultrasonic
sensors. It monitors the area around your vehicle using sensors mounted in
the front and rear bumper. The parking sensor system audibly indicates the
distance between your vehicle and an object being detected.
The rear view or around view monitor
system helps you to manoeuvre your
vehicle by displaying objects behind
and/or around the vehicle, e.g. when
parking your vehicle.
The electronic parking sensor system is automatically activated when:
•
•
•
The ignition is switched on.
The shift lever is in position D or R (automatic transmission models)
or when a forward or reverse gear is selected (manual transmission
models).
The electric parking brake is released.
When an object is detected at the front or rear of the vehicle, the system will
alert you by an audible beep. The nearer the vehicle gets to the object, the
more frequently the beep will sound.
To temporarily switch off the parking sensor system,
push the electronic parking sensor system OFF
switch on the lower part of the instrument panel.
The indicator light in the switch will turn on. Push
the switch again to switch the system on. The
indicator light in the switch will turn off.
When switched OFF, the parking sensor system will automatically be
reactivated when the engine is restarted.
The system will automatically be activated when you
select reverse gear. Also, you can manually activate
the system by pushing the <CAMERA> button
on
the INFINITI Controller. The camera view will only be
displayed with the ignition switched ON.
Pressing the camera button repeatedly will change the
views of the around view monitor.
MOvINg OBJECT DETECTION
The around view monitor is equipped with a Moving Object Detection (MOD)
function. If a moving object is detected, a yellow box will appear around the
camera image and a beep will sound to warn you on the moving object being
detected.
23
Intelligent Park Assist
Intelligent Park Assist is only an aid. It is not a substitute for your attention
to the immediate surroundings. The responsibility for safe manoeuvring and
parking remains with you as the driver of the vehicle.
Intelligent Park Assist can judge whether a parking space is big enough to
park your vehicle in and takes over steering control to park inside the space. It
can also assist with parking into a bay.
Note: when using the Intelligent Park Assist system, steering is taken over by the system.
You need to accelerate and brake yourself!
For full details on using the Intelligent Park Assist system, refer to your
vehicle’s Owner’s Manual.
Cruise Control and Speed Limiter Systems
Intelligent Park Assist is activated automatically when driving forwards with a
speed up to approx. 35 km/h. While in operation, the system independently
locates and measures parking spaces on both sides of the vehicle.
When driving at low speeds,
the parking symbol
will be
displayed in the upper display
(automatic transmission models)
or in the main display (manual
transmission models).
When a parking space is detected at
either side of the road, an arrow
will be displayed at the left or right side of the parking symbol.
Parking spaces on the passenger side will automatically be displayed by the
arrow in the display. For the system to search for and display parking spaces
on the driver's side, the driver's side turn signal light must be switched on.
To confirm a parking space being detected, press the <OK> button on the
steering wheel.
After shifting into reverse gear or selecting the R position on models with
automatic transmission, messages on the vehicle information display will
guide you through the assisted parking procedure.
Cruise Control and Speed Limiter Operation
Cruise control maintains a constant (set) speed for you without the need for
you to depress the accelerator pedal.
The speed limiter limits your speed to a set maximum speed, unless you fully
depress the accelerator pedal.
The systems are operational only at speeds above approx. 30 km/h.
To switch between cruise control and speed limiter operation, quickly push
on the cruise control/speed limiter lever. If the speed limiter is
the button
activated, the <LIM> indicator light
in the lever will illuminate. If the light is
off, cruise control is selected. To deactivate the cruise control system, briefly
push the lever towards the front of the vehicle.
24
FUNCTIONS OF CRUISE CONTROL/SPEED LIMITER LEvER
INTELLIgENT CRUISE CONTROL (ICC)
The ICC system uses a sensor behind the INFINITI logo on the front grille to
detect a vehicle driving ahead of you. If the speed of the detected vehicle is
lower than the speed of your vehicle, the ICC system will automatically reduce
your cruising speed to maintain a distance selected by you.
Note that the ICC system can only apply about 50% of
the total braking force. If the ICC system cannot maintain
the selected distance, a chime will sound and the vehicle
ahead indicator light will come on to notify you to take
necessary action.
Briefly move lever upwards to store the current speed.
Move lever upwards and hold to store a higher speed.
Release lever when desired speed is reached.
Speed limiter ON indicator light.
To increase the distance
to the vehicle ahead to
be maintained by the ICC
system, turn the knob
clockwise. To reduce the
distance, turn the knob
counter-clockwise.
Store current speed or call up last stored speed.
Briefly move lever downwards to store the current speed.
Move lever downwards and hold to store a lower speed.
Release lever when desired speed is reached.
For full details on Cruise Control, Intelligent Cruise Control and Speed Limiter
information, please refer to your vehicle’s Owner’s Manual.
Switch between cruise control and speed limiter.
Deactivate cruise control/speed limiter system.
To start using the cruise control/speed limiter:
on
1. Select either cruise control or speed limiter by pressing button
the lever.
2. Accelerate to the desired speed.
or down
to store the current speed.
3. Briefly press the lever up
4. In case cruise control is selected, you can now take your foot off the
accelerator pedal.
25
Hill Start Assist
BLIND SPOT WARNINg
The Hill Start Assist system automatically keeps the brakes applied for a short
time to prevent the vehicle from rolling as you start to drive away on a downor uphill slope.
This gives you enough time to move your foot from the brake pedal to the
accelerator pedal before the vehicle starts to roll.
The Blind Spot Warning (BSW) helps you to detect vehicles in the lane(s) next
to you.
When the system detects vehicles in a
lane next to you while you operate the
turn signal, a chime will sound twice and
the blind spot warning indicator light
will flash until the detected vehicle has
left the detection zone.
Driver Assistance Systems
Your vehicle may be equipped with following Driver Assistance systems:
• Lane Departure Warning
• Blind Spot Warning
• Forward Emergency Brake
• Traffic Sign Recognition
Blind Spot Warning can be switched on
or off through the [Assist] menu on the
vehicle information display.
LANE DEPARTURE WARNINg
The Lane Departure Warning (LDW)
system operates at speeds above
approx. 60 km/h (37 MPH). If one
of the front wheels passes a lane
marker, you will be warned of this by
means of an intermittent vibration
through the steering wheel for up to
1.5 seconds.
Lane Departure Warning can be
switched on or off through the
[Assist] menu on the vehicle
information display.
26
FORWARD EMERgENCy BRAKE
WARNINg
The Forward Emergency Brake system assists you in avoiding front collisions.
The system uses a radar sensor located behind the INFINITI logo on the front
grille to calculate the distance between your vehicle and the vehicle in front of
you.
If the distance becomes too small, the vehicle ahead
indicator light
will flash. If the distance becomes
even smaller a chime will sound and the forward
collision avoidance system warning light will start
flashing. If finally the distance becomes even smaller,
active braking will be applied to avoid or reduce the impact of a collision with
the vehicle in front of you.
Forward Emergency Brake can
be switched on or off through
the [Assist] menu on the vehicle
information display.
The forward emergency brake system is a supplemental aid to the driver. It is
not a substitute for your attention to traffic conditions or your responsibility
to drive safely. It cannot prevent accidents due to carelessness or dangerous
driving.
The forward emergency brake system may not function under all driving,
traffic, weather and road conditions.
Note: Refer to your vehicle's Owner's Manual for full details on the functioning of the
Forward Emergency Brake system.
TRAFFIC SIgN RECOgNITION
Traffic Sign Recognition (TSR)
displays detected speed limits and
other traffic signs on the vehicle
information display.
It uses a camera, mounted behind
the windshield to detect traffic signs.
If the system detects a conditional
speed limit, then both speeds and
conditions are displayed on the
vehicle information display.
Traffic Sign Recognition settings can be adjusted through [Assist] menu on the
vehicle information display.
27
Fuel Filling
To open the fuel filler lid, unlock the
vehicle and gently push the rear side of
the fuel filler lid.
Bonnet Opening
To open the bonnet, pull the bonnet release handle
at the lower
instrument panel. Then slightly lift up the bonnet and pull lever
sideways
to unlock the bonnet.
28
Infiniti Q30
Publication Number: QR15E-0H15E0E
Printed in France