Speedglas Complete Catalog

Transcription

The Complete
Catalog
What’s New! . . . . . . . . . . . . . . . . . . . . . . .3
Introduction to Auto-Darkening Safety . . .6
“It Breathes!”
(The Speedglas® 9000 Helmet) . . . . . . . . . .8
Speedglas® SideWindows™ . . . . . . . . . . . .10
Speedglas® Utility . . . . . . . . . . . . . . . . . . .12
Speedglas® 9000F . . . . . . . . . . . . . . . . . . . .14
Speedglas® 9000XF . . . . . . . . . . . . . . . . . .16
Speedglas® 9000V . . . . . . . . . . . . . . . . . . .18
Speedglas® 9000X . . . . . . . . . . . . . . . . . . .20
Speedglas® FlexView . . . . . . . . . . . . . . . . .22
Speedglas® ProTop . . . . . . . . . . . . . . . . . . .24
Speedglas® with Adflo® . . . . . . . . . . . . . . .26
Speedglas® Fresh-air® II SA 9000 . . . . . . . .30
SA PRP 200-B Panel . . . . . . . . . . . . . . . . .32
Speedglas® Individual Supplied-Air
Purification & Regulation System . . . . . . .34
Replacement Parts for
Speedglas® Helmets . . . . . . . . . . . . . . . . . .36
FlexView and ProTop . . . . . . . . . . . . . . . . .38
Replacement Parts for Adflo® . . . . . . . . . . .40
Replacement Parts for HWR
(Hornell Welding Respirator)
9000 Helmet Assembly . . . . . . . . . . . . . . .41
Fresh-air® II P & G 9000 . . . . . . . . . . . . . .42
Replacement Parts for SA & PRP 200-B . .44
Welding Lens Shade Guide . . . . . . . . . . . .48
NIOSH List of Respirator
Approval Labels . . . . . . . . . . . . . . . . . . . . .49
Warranty & Customer Support . . . . . . . . . .50
Speedglas® Lens Selector Table . . . . . . . . .B/C
What’s New!
Speedglas
with Adflo
®
®
The most ergonomically perfect
PAPR (powered air-purifying
respirator) available to welders.
HE Filter
Vapor Cartridge
New “stackable” configuration allows welders
to quickly add a vapor cartridge to the high
efficiency particle filter. A Hornell exclusive!
See page 26.
Adflo Turbo
filter cover
High Efficiency
(HE) filter
Spark Arrestor
Prefilter
2
3
What’s New!
Speedglas
FlexView
What’s New!
®
Speedglas
ProTop
®
A perfectly balanced hard hat for welders:
the up position “nests” the helmet down low over
the hard hat for a low center-of-gravity.
Ideal for low-light conditions: a quick lift of the
silver front and welders get a clear, 4.75" x 3.6"
(120 x 90 mm) view, great for weld prep in
poorly-lit locations.
Patented pivot
mechanism securely
locks the helmet in
both the up and
down positions.
The Speedglas FlexView system is compatible with
all Speedglas 9000 auto-darkening welding lenses.
The clear lens
allows for precision
grinding, cleaning
and inspection.
See page 22.
4
Low-profile design
is perfect for
welder protection
in areas with
overhead hazards.
See page 24.
5
Introduction To
Auto-Darkening
Lenses
How It Works
Each Speedglas lens is a laminate of seven different
layers: a UV/IR filter, three polarizers, two liquid
crystal elements and a cover glass. The UV/IR filter
continually blocks harmful radiation, whether the
lens is ON, OFF, light or dark. Aided by surfacemounted electronics, the proprietary liquid crystal
elements act as shutters that detect and react to the
welding arc by instantly shading the lens.
Independent arc-detectors instantly sense the
welding arc, immediately triggering the
Speedglas lens to change from the transparent
state to the dark state.
Safety Products That Increase
Your Performance
Now welders can always see their work, at
comfortable light levels, with constant eye and
face protection. Speedglas lenses turn dark the
moment an arc is struck and transparent again
when welding stops–all the time with full
UV/IR protection.
Auto-darkening eliminates the neck-strain of
“helmet flipping” while greatly increasing the
accuracy of electrode placement.
This, in turn, reduces the need for grinding and
rework. In addition, welders can get into tight,
cramped spaces with full protection and have a
clear view–in effect, making extremely awkward
welds a lot easier.
6
Constant UV/IR Protection:
This filter provides the same UV/IR filtration protection as a
traditional, non-auto-darkening welding lens (as regulated by
USA and Canadian welding safety standards).
Fail-Safe Darkening
When you pick up an unenergized Speedglas lens,
it is in an intermediate dark shade; you must turn it
ON to make it go into the light state. If anything
catastrophic happens to the lens, it simply defaults
back to the darker intermediate OFF shade.
As mentioned above, UV/IR protection is
always present.
Meets Or Exceeds All Applicable
Safety Standards/Approvals:
American National Standard
for eye & face protection.
National Standard of Canada for
Industrial eye & face protection.
7
A Welding Helmet
That Breathes!
But Keeps Out Smoke
The revolutionary Speedglas® 9000
helmet features aerodynamicallydesigned exhaust vents proven to
remove exhaled air without letting
in welding smoke.
Increased Ease-Of-Use
We’ve eliminated those time-consuming lens
fastener screws! Now you simply snap-off the
helmet’s front panel and squeeze two locking tabs
together to quickly remove the lens cassette.
Changing the inner and outer protective lens
plates has never been
easier or faster!
For welders who keep their helmets in the down
position for prolonged periods of time, the build-up
of carbon dioxide (CO2) is greatly reduced
compared to traditional helmet designs.
Laboratory results, as well as extensive field tests,
confirm the helmet’s comfort, with welders
experiencing lower humidity, less heat, and
reduced “stuffiness.” The patented design results
in welders feeling more energetic and clear-headed.
The welder’s natural breathing action directs the
exhaust airflow; no moving parts are involved.
Fresh, incoming air is not drawn through the
special vents; instead, it chooses the path of
least resistance—the area around the welder’s
neck, which is typically further away from the
smoke plume.
Speedglas 9000 construction: Note the
aerodynamic exhaust vents that are located directly
behind the front silver panel. The patented helmet
is extremely comfortable, weighing only 17.4
ounces (including lens) and has excellent balance.
Its narrow width is ideal for welding in tight spots.
The polyamide nylon construction is heat and
chemical resistant and extremely durable.
AUTO OFF
LOW BAT
Speedglas 9000
Helmet Specifications
Helmet Material: polyamide nylon
Helmet Weight (without lens): 10.8oz (306g)
Headband: fully-adjustable, ratcheted design
Exhaled air is directed through the four aerodynamic
vents. It then exhausts through two thin openings
created between the double-shell construction of the
heat-reflecting silver front panel and the black helmet.
8
Speedglas SideWindows™ option: see pages 10 & 11
Replacement Parts: see pages 36 & 37
9
EX
CL
F
US
U.S RO
IVE
.P M
AT
EN HOR
LY
TN
O. NE
L
5
Peripheral Vision
For Welders
,19
L
1,4
68
Eliminate “tunnel vision”...try a Speedglas SideWindows helmet and see
what you’re missing!
SideWindows™ Lenses Improve
Visibility, Safety & Comfort
Now welders can have peripheral vision with
Speedglas SideWindows™ helmets. The two
shade 5 side lenses increase the viewing area by
over 100%.
SideWindows lenses allow welders to see
potentially-hazardous peripheral objects, such as
protruding beams, vehicles, and other welders,
with the helmet down.
The peripheral vision lenses also permit welders to
easily move around their work area with constant
protection from UV/IR radiation.
The two side lenses are designed solely for
peripheral vision; the welder continues to view his
own arc through the center (auto-darkening) lens.
10
SideWindows™ Specifications
Lens Materials: Impact resistant polycarbonate
Lens Shade: 5
Ordering Information
Part Numbers: for complete helmet with
SideWindows, simply add “SW” after helmet part
number.
Note: Very strong sunlight and light from very
close, side-by-side welding may interfere with the
welder’s view of the workpiece; when practical, use
welding partitions to separate welders. The
SideWindows option is not available on the
Speedglas Utility helmet.
11
An Entry-Level
Auto-Darkening
Lens & Helmet
Auto Off–Turns off lens 30 minutes after last arc.
Immediate Off–Simply hold ON/AUTO OFF button down for two seconds.
• UV/IR protection is constant even when lens
is OFF or in the shade 3 light state.
• Super durable, extremely lightweight,
chemical and heat resistant nylon helmet.
• Outstanding optical clarity.
• Extremely dependable performance.
Speedglas Utility Specifications
Light Shade: 3
Dark Shade: factory-set at 10 or 11
Off (Fail-Safe) Shade: nominal 5
The Speedglas® Utility
Viewing Area: 3.57" x 1.68" (91 x 43mm)
Our most affordable auto-darkening lens! The
Speedglas Utility is especially designed for MIG
(GMAW) and stick (SMAW) welding only.
Weight, Helmet with Lens: 17.14oz (486g)
The Speedglas Utility is perfect for the serious
part-time welder, as well as for maintenance
welding on farm equipment, automobiles, and
any other MIG or stick project. Two lens models:
dark shade 10 or 11.
It’s the most affordable auto-darkening
lens and helmet from the world’s leading
manufacturer, Hornell.
Battery Life (Average): 2000 hours
Operating Temperature: 23° to 131°F
(-5° to 55°C)
Part Numbers for complete package–helmet,
headband and auto-darkening lens:
Shade 10: 04-0014-10U
Shade 11: 04-0014-11U
Replacement Parts: see pages 36 and 37.
NOTE: The complete Speedglas Utility Lens
& Helmet package is not sold with the (vented)
Speedglas 9000 helmet, SideWindows™ or
Hard Hat options.
12
13
A Lens For All Arc
Welding Processes
• Works with all arc welding processes.
• Shade 3 light state.
• The world’s finest auto-darkening
electronics and optical quality.
• Rugged: able to withstand harsh treatment
better than any other automatic lens.
Speedglas 9000F Specifications
Light Shade: 3
The Speedglas® 9000F
Dark Shade: factory-set at 10, 11 or 12
Do MIG, TIG, stick, and all other arc welding
processes with one lens!
The Speedglas 9000F (“F” for “Fixed” dark shade)
provides improved performance, greater ease-ofuse, and remarkable optical clarity. Available in
three factory-set dark shades: 10, 11 or 12.
Plus, all Speedglas 9000 helmets have four exhaust
vents for CO2 reduction (see page 8).
(-5° to 55°C)
Shade 10: 04-0012-10
Shade 11: 04-0012-11
Shade 12: 04-0012-12
Add “H” for Hard Hat and/or “SW” for SideWindows™.
14
15
An X-tra Large
Lens
Sensitivity Adjustment–Provides additional adaptability, under a variety
of lighting conditions, when in the manual sensitivity mode.
Shade 3 Light State–For outstanding visibility.
Speedglas 9000XF Specifications
Light Shade: 3
Dark Shade: factory-set at 10, 11 or 12
The Speedglas 9000XF
For welders that want a really big view...
the Speedglas 9000XF (“X-tra Large, Fixed
Dark Shade”).
(-5° to 55°C)
It’s 44% larger than most auto-darkening lenses,
with outstanding optical clarity and very low
angle dependency.
The Speedglas 9000XF can also be used on all
arc welding processes. Available in three
factory-set dark shades: 10, 11 or 12.
Shade 10: 04-0012-10X
Shade 11: 04-0012-11X
Shade 12: 04-0012-12X
16
17
“V” for Variable
Dark Shades
Immediate Off–Simply hold the ON/OFF button down for two seconds.
“V” for Variable Dark Shades–5 dark shades (gold numbers) for stick,
MIG and TIG; plus 3 dark shades (red numbers) for low-amp TIG and
other welding conditions.
of lighting conditions, when in the red (“low-amp TIG”) numbers.
The Speedglas® 9000V
For welders handling a variety of amperages and
different arc welding processes, we offer the
Speedglas 9000V.
The Speedglas 9000V provides five user-selectable
dark shades for stick, MIG and TIG welding: 9, 10,
11, 12 and 13. For low-amp TIG and other welding
conditions, the welder can select from three dark
shades: 9, 11 and 13.
Speedglas 9000V Specifications
Light Shade: 3
Dark Shades: user-selectable to 9, 10, 11, 12 and 13
(-5° to 55°C)
04-0012-30
18
19
The Top-Of-TheLine Speedglas
Lens & Helmet
®
Immediate Off–Simply hold the ON/OFF button down for two seconds.
5 Dark Shades–5 dark shades (gold numbers) for stick, MIG and TIG;
plus 3 dark shades (red numbers) for low-amp TIG and other welding
conditions.
of lighting conditions, when in the red (“low-amp TIG”) numbers.
Solar Panel–Maximizes battery life.
Speedglas 9000X Specifications
Light Shade: 3
The Speedglas® 9000X
An X-tra large viewing area, combined with five
user-selectable dark shades for stick, MIG and TIG
welding. For low amp TIG and other welding
conditions, the welder can select from three dark
shades: 9, 11 and 13.
The Speedglas 9000X has a big 4.09" x 2.13"
viewing area, with clear, sharp optics and consistent
shading across the entire viewing area.
A solar panel on the front of the lens cassette helps
to power the unit, extending battery life to
approximately 3000 hours.
Dark Shades: user-selectable to 9, 10, 11, 12 and 13
(-5° to 55°C)
04-0012-20
20
21
Ideal For Poor
Lighting Conditions
Speedglas® FlexView in a
“Breathable” Helmet
The FlexView system is the only product to offer
users a clear visor combined with a “breathable,”
CO2-reducing helmet: the Speedglas 9000.
The helmet’s four aerodynamically designed
exhaust vents have been proven to reduce carbon
dioxide (CO2), heat, and humidity. As a result,
users feel more energetic and clear-headed all
day long.
And with the exclusive Speedglas SideWindows™
model, users can increase the helmet’s viewing area
by 100% via two shade 5 peripheral lenses.
4.75"
3.6"
The Speedglas® FlexView
The new Speedglas® FlexView has a big, 4.75" x
3.6" (120 x 90 mm) clear polycarbonate lens that’s
ideal for precision weld preparation under low
light conditions.
The user simply lifts up the spring-mounted
Speedglas lens assembly for weld prep. The spring
holds the auto-darkening lens securely on top of
the helmet, giving the welder a big, clear view
behind the FlexView protection lens.
The clear lens allows for precision grinding and
cleaning, the careful alignment of electrodes and
the inspection of newly-completed welds…all with
constant eye and face protection, even in the
darkest workshop.
The clear lens meets the ANSI Z87.1 industrial eye
and face protection standard, which does not
recommend “…filter or tinted lenses that restrict
light transmittance…” when chipping or grinding
(American National Standard Z87.1-1989, page 16,
Selection Chart, Impact Protectors).*
*Impact resistant, primary eye protection, spectacles or goggles that meet
current ANSI specifications, must be worn at all times when using any
welding helmet.
Speedglas FlexView Specifications
Safety Standards:
ANSI Z89.1
Helmet Material:
Polyamide nylon
Weight:
20oz (565g)
Part Number: Speedglas FlexView complete
04-0016-(Lens Options)
Speedglas Lens Options
10, 11 or 12:
Speedglas 9000F Lens
Shade 10, 11 or 12
Viewing Area
3.57" x 1.68" (91 x 43mm)
10X, 11X or 12X:
Shade 10, 11 or 12
Viewing Area
4.09" x 2.13" (104 x 54mm)
30:
Speedglas 9000V Lens
Viewing Area
3.57" x 1.68" (91 x 43mm)
20:
Speedglas 9000X Lens
Viewing Area
4.09" x 2.13" (104 x 54mm)
Add “SW” for SideWindows™.
Replacement Parts: see page 38.
22
23
A Perfectly
Balanced Hard Hat
For Welders
Low-Profile Hard Hat
Goes Into Tight Spaces
The special ABS hard hat has a low-profile that is
excellent for entering space-restricted areas. Its
short brim design means the welding helmet and
lens are closer to the welder’s face, which is ideal
for precision welding. The hard hat has a ratcheting
headband for fast, secure, top-of-the-head sizing.
Its sweatband is made from terry cloth and soft
foam and its six-point webbing system provides
excellent shock absorption and comfort.
Speedglas ProTop Specifications
ANSI Z87.1 (Eye & Face)
ANSI Z89.1 (Head Protection)
Hard Hat Material: White ABS Plastic
Headband Adjustments:
19.5" to 25" (50 to 64mm)
Weight: Hard Hat only
13.7oz (390 g)
Weight: Hard Hat with Speedglas 9000V lens
31.2oz (890 g)
Part Number: Speedglas ProTop Welding Helmet
with Pivot mechanism, Hard Hat and Strap
Safety Standards:
The Speedglas® ProTop
The new Speedglas® ProTop combination hard hat,
welding helmet, and auto-darkening lens system is
especially designed for welders working in areas
with overhead hazards, such as cranes, protruding
beams and moving machinery.
The key to the Speedglas ProTop system is the
exclusive pivot mechanism that connects the
welding helmet to the hard hat. Traditional welding
hard hats create a very high center-of gravity when
the welding helmet is raised; as a result, the user
feels off-balance, and the leveraged weight puts
additional strain on neck muscles. On the other
hand, the ProTop pivot mechanism has two sets of
axes: one to lift the welding helmet away from the
welder’s face, and another axis to “nest” the
welding helmet down low over the hard hat, in a
perfectly balanced, locked-down position. The
welding helmet automatically unlocks when the
welder pulls it back down into position over
the face.
In addition to having a much more comfortable
(lower) center-of-gravity, the nested welding helmet
is much less likely to bump into obstacles as the
welder moves around the work area.
24
Speedglas Lens Options
10, 11 or 12:
Shade 10, 11 or 12
Viewing Area
3.57" x 1.68" (91 x 43mm)
10X, 11X or 12X:
Shade 10, 11 or 12
Viewing Area
4.09" x 2.13" (104 x 54mm)
30:
Viewing Area
3.57" x 1.68" (91 x 43mm)
20:
Viewing Area
4.09" x 2.13" (104 x 54mm)
25
The Most Advanced
PAPR Available
Exclusive “stackable”
configuration adapts to changing
welding applications.
Environmentally-friendly NiMH
battery charges in less than 3
hours with a smart charger that
won’t ever overcharge.
System Intelligence: Constant
Airflow Rate, regardless of battery
charge and filter loading. Audible
and visual alarms signal low
airflow and low battery charge.
The unique belt design has a solid
leather front, cut narrow to allow
the welder to bend forward easily.
Along the welder’s sides, the
leather becomes wider, with large
ventilation holes for maximum
breathability. The turbo unit
securely attaches to, and is nestled
between, the two plastic arms of
the belt so the turbo’s weight is
evenly distributed across the entire
lower back and upper hips. The
plastic arms are vertically rigid
but with pleats so the welder can
move and turn with freedom.
Exclusive airflow pattern means
perfectly-distributed air
throughout the entire breathing
zone of the helmet.
26
27
Two Respira tors In One!
High Efficiency (HE)
Particle Filter.
Adflo Cartridge for
OV/SD/CL/HC vapors.
Brushless Motor lasts
3x longer than
traditional motors.
Adflo Turbo
filter cover
Spark
Arrestor
High Efficiency
(HE) filter
Prefilter
We’ve reinvented the powered air-purifying respirator
for welders. The result is Speedglas® with Adflo®:
a lightweight, compact, all-in-one system. Its exclusive
“stackable” configuration means that the Adflo cartridge
can be “stacked” onto the High Efficiency (HE) particle
filter for additional protection against organic, sulfur
dioxide, chlorine, and hydrogen chloride vapors.
In effect, it’s two systems in one, allowing increased
user flexibility to adapt to changing welding
applications. And you can selectively replace either the
particle filter or the Adflo OV/SD/CL/HC cartridge as
needed: you don’t have to change both filters at the
same time!
The Adflo system has no external batteries, no battery
cables, and no sharp corners. Its slim profile is designed
to go into tight spaces. And it’s the most ergonomically
perfect PAPR available to welders.
NiMH Battery fully
charges in three hours.
Adflo Specifications
Assigned Protection Factor:25
Airflow (nominal): 6+ cfm (170+ lpm) minimum
Battery, NiMH:
HE:
up to 12 - 13 hrs/charge
HE + OV/SD/CL/HC: up to 5.5 - 6 hrs/charge
Battery Charging Time: 3 hours
System Weights
Helmet assembly w/ 9000X lens:
1.79 lbs (0.81 kg)
Adflo Turbo w/ Battery, Breathing Tube & Belt:
4.48 lbs (2.03 kg)
OV/SD/CL/HC Cartridge: 1.79 lbs (0.81 kg)
Operating Temperatures:
23° to 131°F (-5° to 55°C)
Respirator Approval: NIOSH 42 CFR 84
Complete Systems
Standard (HE):
HE + OV/SD/CL/HC Cartridge:
Lens Options:
10, 11 or 12 =
shade 10, 11 or 12
10X, 11X or 12X = Speedglas 9000XF Lens
shade 10, 11 or 12
30 =
Speedglas 9000V lens
20 =
Speedglas 9000X lens
WARNING
Not to be used in atmospheres classified as IDLH. Not to be used in atmospheres
of less than 19.5% oxygen. Final determination of respirator applicability and
filter selection must be made by an on-site safety specialist or industrial hygienist.
28
29
Supplied Air
Protection
• Control-air valve allows
adjustment of the airflow rate
for personal preference.
• Cool-air valve permits
welder to lower the
temperature of the
supplied air by up to
45°F (25°C).
• Temp-air valve
allows either
cooling or
warming of the
supplied air ±45°F
from the supplied air
temperature.
Valve
Model
Control-air
Cool-air
Temp-air
Max. # of
CFM
Pressure
CFM
Required Delivered Range (psig) Hoses/Length*
6-15
12-25
12-25
6-15
6-15
6-15
65-70
70-105
85-110
6 hoses/300'
4 hoses/100'
4 hoses/100'**
*Indicates maximum number of hoses and maximum total length.
**Temp-air valve is approved for use with Breather Hose only.
Speedglas Fresh-air® II SA 9000
FA II SA 9000 Specifications
For highly contaminated welding environments,
you need the Speedglas Fresh-air II Supplied Air
(SA) 9000 system.
Assigned Protection Factor (APF): 25
Airflow:
6+ cubic feet per minute
(170+ lpm)
System Weights
Helmet assembly with 9000X lens:
1.79 lbs (0.81 kg)
Control-air Valve with Breathing Tube, and Belt:
1.85 lbs (0.84 kg)
Cool-air Valve with Breathing Tube, and Belt:
2.11 lbs (0.96 kg)
Temp-air Valve with Breathing Tube, and Belt:
2.37 lbs (1.07 kg)
Operating Temperatures: 23° to 131°F (-5° to 55°C)
Respirator Approval: NIOSH 42 CFR 84
The NIOSH-approved Speedglas Fresh-air II SA
9000 system provides respiratory protection from
high levels of particle fumes and gases. The
lightweight, belt-mounted valves permit the welder
to adjust the airflow levels anywhere from 6 to 15
cfm (170 to 425 lpm), making it ideal for very hot
or strenuous jobs.
Complete Systems
Control-air:
Cool-air:
Temp-air:
Lens Options:
10, 11 or 12 =
NOTE: Final determination of
respirator applicability and
filter selection must be made
by an on-site safety specialist
or industrial hygienist.
shade 10, 11 or 12
10X, 11X or 12X = Speedglas 9000XF Lens
shade 10, 11 or 12
30 =
20 =
Add “H” for Hard Hat and/or “SW” for
SideWindows™.
Replacement Parts: see page 41 and 44.
30
31
OSHA specification 29 CFR 1910.134(i)(1)(ii) states:
“Breathing air shall meet at least the requirements
of the specification for Grade D air as described in
ANSI/Compressed Air Association Commodity
Specification G-7.1-1989.”
OSHA specification 29 CFR 1910.134(i)(7) states:
“For oil-lubricated compressors, the employer shall
use a high temperature or carbon monoxide alarm,
or both, to monitor carbon monoxide levels. If only
high-temperature alarms are used, the air supply shall
be monitored at intervals sufficient to prevent carbon
monoxide in the breathing air from exceeding 10 ppm.”
SA PRP 200-B: 18-0902-00
32
7
4
3
6
5
▲
Outlet Air Quality:
Dirt Particles less than 0.01 micron.
Oil Mix/Mist/Aerosol less than 0.01 ppm.
Vapor/Odor removal down to 0.003 ppm.
Inlet Connection: One 3/4" NPT (female).
Outlet Connections: Four Parker Hannifin
Model B32-E Quick Disconnects.
Maximum Flow Rate: 110 scfm.
Maximum Inlet Pressure: 150 psig.
Pressure Relief Valve Setting: 125 psig.
Adjustable Outlet Pressure: to 100 psig.
Recommended Max. Working Temp.: 86°F(30°C).
Recommended Min. Working Temp.: 35°F (2°C).
Audible Alarm: Continuous at 90 dba;
factory-set at 10 ppm CO.
Visual Alarm: CO alarm indicator LED. Filter
maintenance indicator.
CO Monitor:
Display: 4 digit LCD.
Sensor: Electronic chemical cell type.
Power: 110 Volt AC power supply.
Dimensions: Length 36.6" (930 mm); Width 24.2"
(615 mm); Depth 7.3" (185 mm).
Weight: 55 lbs (25 kg).
Compliance Standards:
USA 29 CFR 1910.134
CSA Z1801.1-00
ISO 8573.1: Class 1.-.1
1
9
▲
SA PRP 200-B Panel Specifications
1. Carbon monoxide
monitor and alarm.
Four-digit liquid
crystal display
indicates the carbon
monoxide
concentration.
2
Should the level
of CO exceed alarm
set points, a warning
LED light will turn
on, as well as a 90
decibel audible
alarm. The monitor
also features an
alarm test switch and
external calibration
and test gas inlet.
▲
Air Purification &
Regulation Panels
8
10
2. Compressed air inlet: one 3/4" NPT (female).
3. Stage 1 Filter: Water Separator with centrifugal
action and impingement separation to remove
large quantities of excessive liquid contamination.
4. Pressure differential indicator to indicate when
filter element change is required.
5. Stage 2 Filter: General Purpose Protection Filter
removes particulates down to 1.0 micron,
including water and oil aerosols. Maximum
remaining oil aerosol content is 0.5 ppm at 70°F.
Recommended filter life of 6,000 hours.
6. Stage 3 Filter: High Efficiency Coalescing Filter
removes particles down to 0.01 micron, including
water and oil aerosols. Maximum remaining oil
aerosol content is 0.01 ppm at 70°F.
Recommended filter life of 6,000 hours.
7. Stage 4 Filter: Activated carbon filter removes
oil vapor and hydrocarbon odors. Maximum
remaining oil content of less than 0.003 ppm at
70°F. Recommended filter life of 1,000 hours.
8. De-pressurization valve to vent the compressed air
in the filter housing prior to filter element change.
9. Liquid level indicator for confirmation that
automatic condensate drain is operational.
10. Breathable air outlets: four Parker Hannifin quick
disconnects supply air for up to 4 welders.
33
Individual SuppliedAir Purification &
Regulation System
The Speedglas® Individual Supplied-Air
Purification & Regulation System is especially
designed for welders requiring supplied-air
respiratory protection.
1. Designed for wall-mounting.
2. Two heavy-duty metal cylinders protect
the two-stage filter elements.
3. A particulate/coalescing element that removes
particles and oil down to 0.01 micron size.
4. An activated carbon/absorption element that
removes odors and any remaining oil content
down to 0.003 ppm.
5. A pressure gauge on its outlet side.
34
▲
5
3
▲
▲
8
▲
▲
The BA-2013 Purifier is a simple yet very rugged
system:
4
1
▲
The CO Monitor has a 90-decibel alarm that warns
users of unacceptable CO levels in the compressed
air line. With the CO Monitor installed, one air
supply line can provide air to numerous BA-2013
Purifiers, which can then be added to the supply
line in a modular fashion for increased work area
flexibility. This modular, one welder/one Purifier
approach also provides for significant cost savings
due to the shared CO Monitor.
2
▲
The Speedglas® Individual Supplied-Air
Purification & Regulation System includes a
Breathing Air Purifier and Regulator (BA-2013)
and a Carbon Monoxide Monitor (CO-2013) with
power supply.
Carbon Monoxide Monitor (CO-2013).
▲
The compact, single-user system connects to
standard “shop” compressed air sources that are
free of carbon monoxide and are not oxygendeficient. The purification system removes oils,
particulates, and odors from the air supply,
providing filtered air that meets or exceeds OSHA,
CSA and ISO standards. With a 100 psig
compressed air supply, the system will provide a
welder with 27 scfm of breathable air at 100 psig.
9
7
▲
6
Breathing Air Purifier and Regulator (BA-2013).
6. A de-pressurization valve to vent the compressed air
in the filter prior to a filter change.
7. A liquid level indicator for confirmation that the
automatic condensate drain is operational.
8. A standard 3/8" NPT inlet.
9. A Parker Hannifin B32 quick disconnect outlet.
Ordering Information & Replacement
Parts
See page 46.
35
Replacement Parts
for Speedglas Utility
& Speedglas 9000
Lens & Helmets
Complete Speedglas 9000F
Lens & Helmet
04-0012-(shade 10, 11 or 12)X Complete Speedglas 9000XF
Lens & Helmet
04-0012-30
Complete Speedglas 9000V
Lens & Helmet
04-0012-20
Complete Speedglas 9000X
Lens & Helmet
For any of the above part numbers, add “H” for Hard Hat
and/or “SW” for SideWindows™
04-0014-(shade 10 or 11)U
Complete Speedglas Utility
Lens & Helmet
04-0660-00
02-0024-00
Lens
Complete Helmets & Lenses
04-0012-(shade 10, 11 or 12)
04-0650-00
04-0026-00
02-0645-00
04-0212-00
04-0320-00
04-0290-00
or
04-0280-00
04-0112-00 for
Speedglas 9000
or
04-0114-00 for
Speedglas Utility
04-0270-00 04-0390-00
or
04-0270-03
04-0270-04 04-0380-00
Lenses
04-0000-(shade 10, 11 or 12)
04-0000-(shade 10, 11 or 12)X
04-0000-30
04-0000-20
Speedglas 9000F Lens only
Speedglas 9000XF Lens only
Speedglas 9000V Lens only
Speedglas 9000X Lens only
02-0690-00
18-0099-68
Lens Replacement Parts
04-0270-00 Outside Protection Plate Standard-package of 10
04-0290-00 Inside Protection Plate for Utility, 9000F and
9000V-package of 5
04-0280-00 Inside Protection Plate for 9000X and
9000XF-package of 5
04-0480-00 9000XF and 9000X Accessory Kit
(10 Outside, 5 Inside Plates and 2 Batteries)
04-0490-00 Utility, 9000F and 9000V Accessory Kit
(10 Outside, 5 Inside Plates and 2 Batteries)
04-0320-00 Battery-package of 2
04-0380-00 Battery Holders (Blue)-package of 2
04-0390-00 Battery Holders (Black)-package of 2
Lens Accessories
04-0290-01 Inside Protection Plate, Passive Filter #1,
for Utility and 9000F models-package of 5*
for Utility and 9000F models-package of 5*
for 9000XF-package of 5*
for 9000XF-package of 5*
04-0270-03 Outside Protection Plate HD
(Heavy Duty)-package of 5
04-0270-04 Outside Protection Plate
High Heat-package of 5
36
*Total shade level must not exceed shade #13.
Do not use Shaded Inside Protection Plates
for either 9000V or 9000X lenses.
Helmet Replacement Parts
04-0012-00 Speedglas 9000
Welding Helmet with Headband
04-0112-00 Speedglas 9000
Inner Welding Helmet only
For any of the above part numbers, add “H” for Hard Hat
and/or “SW” for SideWindows™
04-0014-00 Speedglas Utility
Welding Helmet with Headband
04-0114-00 Speedglas Utility
Inner Welding Helmet only
04-0212-00 Silver Front Panel
04-0650-00 Headband; complete
with mounting hardware
04-0660-00 Mounting Hardware
04-0026-00 Speedglas 9000 and Utility
helmet/headband “S” stop-package of 10
02-0024-00 Sweatband in plastic
Helmet Accessories
02-0645-00
18-0099-68
02-0690-00
02-0014-00NR
02-0023-00
Head Protector
Throat and Side Protector, Leather (3 parts)
Throat Protector
Hard Hat Adapter
Hard Hat with Mounting Hardware
37
Replacement Parts
for Speedglas
FlexView
Replacement Parts
for Speedglas
ProTop
04-0126-00
04-0026-00
04-0025-00
04-0260-00
04-0315-00
04-0361-00
04-0116-00
or
04-0116-00SW
04-0360-00
04-0015-00-(Lens Options)
04-0216-00
04-0215-00
04-0016-(Lens Options) Complete Speedglas FlexView
04-0016-00
Complete Speedglas FlexView With No Lens
04-0116-00
Speedglas FlexView Shell Only
04-0116-00SW Speedglas FlexView Shell Only
with SideWindows™
04-0126-00
FlexView Helmet/Headband
“S” Stop Left-package of 10
04-0026-00
FlexView Helmet/Headband
“S” Stop Right-package of 10
04-0216-00
FlexView Silver Front Panel Only
04-0360-00
FlexView Welding Lens Holder
04-0361-00
FlexView Middle Helmet Panel
04-0260-00
FlexView Protection Plate-package of 10
38
04-0015-(Lens Options) Complete Speedglas ProTop
04-0025-00
Speedglas ProTop welding
helmet with pivot mechanism
04-0215-00
04-0315-00
Speedglas ProTop hard hat
with headgear
Speedglas ProTop strap
39
Replacement Parts
For Adflo
®
15-1099-07
15-0399-99
Replacement Parts
for HWR (Hornell
Welding Respirator)
Helmet Assembly
Head Cover
18-0099-30
15-0099-10
HWR/FA II 9000 Helmet with
Velcro® & Foam: 14-0099-32
(Hardware: 14-0099-70 & Face
Seal: 14-0099-28
sold separately)
14-0099-35
15-0099-06
15-1099-01
®
Turbo
Face Seal
14-0099-28
}
15-0199-99
15-0099-99
15-0009-99
15-1099-81
04-0000-(Lens)
15-0099-05
15-0099-16
15-0099-08
18-0099-33
Replacement Filters & Cartridges
15-0099-99X06 6-pack Adflo Prefilter
15-0099-99X12 12-pack Adflo Prefilter
}
15-0199-99X02 2-pack Adflo HE Particle Filter
15-0399-99X02 2-pack Adflo OV/SD/CL/HC Cartridge
15-0399-99X06 6-pack Adflo OV/SD/CL/HC Cartridge
15-0009-99X02 2-pack Adflo Spark Arrestor
Adflo Turbo Replacement Parts
15-1099-01
15-1099-81
15-5401-01
Adflo Turbo Assembly and Filter Cover
without Filter or Cartridge or Battery
Adflo Turbo Filter Cover
Adflo Turbo, complete with Breathing Tube
Assembly, Flow Indicator, Belt, Spark Arrestor,
Adflo Turbo Filter Cover, Prefilter, HE Particle
Filter, Battery and Smart Charger.
Miscellaneous Replacement
Parts and Accessories
40
15-0099-05
15-1099-07
15-0099-08
15-0099-10
Flow Indicator
Adflo Battery Pack
Adflo Battery Smart Charger
Adflo Breathing Tube Assembly (Rubber)
15-0099-16
18-0099-16
15-0099-06
18-0099-33
Adflo Leather Belt
Comfort Belt
Adflo Leather Belt Front Piece Replacement
Carry Bag
HWR/FA II 9000 Headband Assembly with Air
Duct: 14-0099-29 (Hardware sold separately:
14-0099-70)
18-0099-27
14-0099-28
14-0099-29
18-0099-30
14-0099-35
14-0099-35SW
14-0099-70
04-0212-00
Elastic Duct Retainer (pair)
HWR/FA II 9000 Face Seal
HWR/FA II 9000 Headband Assembly with Air Duct
Head Cover, cloth
HWR/FA II 9000 Helmet Assembly Complete
HWR/FA II 9000 SideWindows™
Helmet Assembly Complete
HWR/FA II 9000 Helmet
(with Velcro® and foam only)
HWR/FA II 9000 SideWindow™ Helmet
(with Velcro and foam only)
HWR/FA II 9000 Helmet Assembly Hardware Kit
Silver Front Panel
04-0000-10
04-0000-11
04-0000-12
04-0000-10X
04-0000-11X
04-0000-12X
04-0000-30
04-0000-20
04-0000-22
Speedglas 9000F Lens only, shade 10
Speedglas 9000XF Lens only, shade 10
Speedglas 9000V Lens only
Speedglas 9000X Lens only
Speedglas 9000Xi Lens only
14-0099-32
14-009932SW
41
Speedglas Fresh-air II
P 9000 Systems
Not User-Serviceable
Front
Blower
Body
Unit
Filter
Molding
Gasket
17-1099-82
Filter
17-0199-99
Speedglas Fresh-air II
G 9000 Systems
Not User-Serviceable
Rear Body
Molding
Front Body
Molding
Rear Body
Molding
Blower
Unit
Filter
Cover
17-1099-81
Filter
Battery
Pack
17-2099-07
Battery Pack
17-1099-07
Filter
Replacement Filters
17-0199-99X02 2-pack of HE (P3) Particle Radial Filter
Replacements for FA II Turbo Unit “P”
Turbo Unit Replacement Parts
17-1099-01
17-1099-81
17-1099-82
FA II Turbo Unit “P” Assembly
without Filters or Battery Pack
FA II Turbo Unit “P” Filter Cover
FA II Turbo Unit “P” Filter Gasket
Miscellaneous Replacement Parts
and Accessories
17-0099-05
17-1099-07
17-0099-08
17-0099-08N10
17-0099-10
17-0099-54
18-0099-16
18-0099-33
FA II Air Flow Indicator
FA II Turbo Unit “P” 3-Cell Battery Pack
FA II Battery Charger
FA II 10-Unit Battery Charger (Smart Charger)
FA II Breathing Tube Assembly
FA II Breathing Tube Cover
Comfort Belt
Carry Bag
Complete Fresh-air II G 9000
Hard Hat Systems
14-3301-(Lens Options)H; comes with three
HE/OV/SD/CL/HC (AEP3) Cartridges
14-3201-(Lens Options)H; comes with three HE (P3) Filters
Lens Options:
10, 11 or 12 = Speedglas 9000F Lens shade 10, 11 or 12
10X, 11X or 12X = Speedglas 9000XF Lens shade 10, 11 or 12
30 = Speedglas 9000V Lens
20 = Speedglas 9000X Lens
add “SW” for SideWindows™
Replacement Filters/Cartridges
17-0299-99X06 6 pack of HE (P3) Particle Filters
17-0299-99X36 36 pack of HE (P3) Particle Filters
17-0399-99X06 6 pack of HE/OV/SD/CL/HC (AEP3)
Cartridge Filters
Turbo Unit Replacement Parts
17-3099-01
FA II Turbo Unit “G” Assembly without
Filters/Cartridges or Battery Pack
Miscellaneous Replacement Parts
and Accessories
17-0099-05
17-2099-07
17-0099-08
17-0099-08N10
17-0099-10
17-0099-54
18-0099-16
18-0099-33
For HWR (Hornell Welding Respirator) Helmet
Assembly Replacement Parts & Accessories,
see page 41.
42
FA II Air Flow Indicator
FA II Turbo Unit “G” 4-Cell Battery Pack
FA II Battery Charger
FA II 10-Unit Battery Charger (Smart Charger)
FA II Breathing Tube Assembly
FA II Breathing Tube Cover
Comfort Belt
Carry Bag
see page 41.
43
Replacement Parts
for Speedglas
Fresh-air II SA 9000
Systems
Replacement Parts
for Supplied Air
Purification &
Regulation Panels
Control-air valve:
Sintered Bronze Filter
Retaining Ring
Gasket
Complete Fresh-air II SA 9000 Systems
Control-air: 14-5601-(Lens Options)
Cool-air:
Temp-air:
Lens Options:
10, 11 or 12 = Speedglas 9000F Lens shade 10, 11 or 12
10X, 11X or 12X = Speedglas 9000XF Lens shade 10, 11 or 12
30 = Speedglas 9000V Lens
20 = Speedglas 9000X Lens
add “H” for Hard Hat and/or “SW” for SideWindows™
18-0902-00 Air Purification & Regulation Panel SA PRP 200-B
18-0099-82 Filter Element Kit for SA PRP 200 and SA PRP 200-B
18-0099-83 K145AO Filter Element
18-0099-84 K145AA Filter Element
18-0099-85 K065AC Filter Element
Replacement Valves and Valve Parts
18-0099-46
18-0099-47
18-0099-48
18-0099-52
18-0099-55
18-0099-63
Control-air Valve Assembly
Cool-air Valve Assembly
Temp-air Valve Assembly
Sintered Bronze Disk (Control-air Valve only)
Valve Shield
Breathing Tube (Supplied Air) Hard Hat
Air Supply Hoses
18-0099-40
18-0099-41
18-0099-42
18-0099-43
18-0099-44
18-0099-45
18-0902-06
25 feet Breather Hose, with Couplings
25 feet Nycoil™ Hose, with Couplings
Air Source Quick Connect
Miscellaneous Replacement Parts and
Accessories
18-0099-16
18-0099-33
Comfort Belt
Carry Bag
18-0099-86 Automatic Drain for SA PRP 200, PRP 200-B
and BA-2013
18-0099-87 DPI Filter Differential Indicator for SA PRP 200
and PRP 200-B
18-0099-88 SKG1 Bowl Sight Glass (with gaskets and screws)
for SA PRP 200, PRP 200-B and BA-2013
18-0099-89 MAK3 Service Kit for SA PRP 200
and PRP 200-B
18-0902-01 CO Calibration Kit for SA PRP 200,
PRP 200-B and BA-2013
18-0902-03 Zero Gas Cylinder (Nitrogen)
18-0099-91 CO Cylinder (50 ppm) for SA PRP 200,
18-0902-04 CO Sensor for SA PRP 200-B and CO-2013
18-0099-94 MAK2 Service Kit for SA PRP 200,
see page 41.
44
45
Hornell Individual
Supplied Air
Purification System
Carbon Monoxide Monitor (CO-2013).
Breathing Air Purifier and
Regulator (BA-2013).
14-0902-00
Individual Supplied Air Purification and Regulation
System: CO-2013 CO Monitor with Power Supply, and
one BA-2013 Breathing Air Purifier and Regulator
14-0902-05
CO-2013 CO Monitor with Power Supply
and Filter/Regulator
14-0902-01
BA-2013 Breathing Air Purifier
14-0099-84
14-0099-85
14-0099-82
18-0099-86
KO17AA Particulate/Coalescing Filter Element
KO13AC Activated Carbon/Absorption Filter Element
Filter Element Kit for BA-2013 (AA and AC elements)
Automatic Drain for SA PRP 200, PRP 200-B
and BA-2013
SGK1 Bowl Sight Glass (with gaskets and screws)
MAK2 Service Kit for SA PRP 200,
18-0099-88
18-0099-94
14-0099-88
18-0902-05
14-0902-85
18-0902-04
14-0099-83
18-0902-03
18-0902-01
18-0099-91
46
18-0902-06
CO Monitor Filter/Regulator only
CO Monitor with Power Supply
CO Monitor Power Supply Only
CO Monitor Sensor Element Replacement
Filter Element Grade 6 for CO Monitor Filter/Regulator
Zero Gas Cylinder (Nitrogen)
CO Calibration Kit for SA PRP 200,
CO Cylinder (50ppm) for SA PRP 200,
Quick Connect, Parker Hannifin (F)
Featured Products
Accessory Kits: 10 outside
and 5 inside protection
plates, plus 2 lens batteries.
See page 36.
Outside Protection Plates:
standard, HD (Heavy Duty)
and High Heat. See page 36.
Throat Protector: “Bib”
made from flame-resistant
cloth. See page 37.
Leather Protectors: one
throat and two side
protectors made from
leather. See page 37.
Head Protector: made from
flame-resistant cloth. See
page 37.
47
Welding Lens
Shade Guide*
Suggested
Minimum Protective
Welding
Arc Current Protective
Shade
Process
(Amperes)
Shade
(Comfort)
Shielded Metal Arc
Less than 60
7
—
Welding (SMAW)
60 to 160
8
10
160 to 250
10
12
250 to 550
11
14
Gas Metal Arc Welding
Less than 60
7
—
and Flux Cored
60 to 160
10
11
(GMAW)(MIG)
160 to 250
10
12
250 to 550
10
14
Gas Tungsten Arc Welding Less than 50
8
10
(GTAW)(TIG)
50 to 150
8
12
150 to 500
10
14
Air Carbon (light)
Less than 500
10
12
Air Carbon (heavy)
500 to 1000
11
14
Plasma Arc Welding (PAW) 20 to 100
8
10
100 to 400
10
12
400 to 800
11
14
Plasma Arc Cutting (PAC)
Light
Less than 300
8
9
Medium
300 to 400
9
12
Heavy
400 to 800
10
14
Carbon Arc Welding (CAW) —
—
14
*Based on ANSI/ASC Z49.1, AWS F2.2-89. Shade numbers are given as guide only and
may be varied to suit application needs. Consult your on-site training officer, industrial
hygienist, or safety manager.
Complete List of Allowed
Standard Protections,
Cautions and Limitations
for Approval Labels*
Protection
N100-Particulate
Filter (99.97% filter
efficiency level)
effective against
particulate aerosols
free of oils; time use
restrictions may
apply
R100-Particulate
Filter (99.97%
filter efficiency
level) effective
against all particulate
aerosols; time use
restrictions may
apply
P100-Particulate
Filter (99.97%
filter efficiency
level) effective
against all particulate
aerosols
N99-Particulate
filter (99% filter
efficiency level)
effective against
free of oil; time use
restrictions may
apply
N99-Particulate
filter (99% filter
efficiency level)
effective against all
particulate aerosols;
time use restrictions
may apply
N99-Particulate
filter (99% filter
efficiency level)
N95-Particulate
filter (95% filter
efficiency level)
effective against
free of oil; time use
restrictions may
apply
N95-Particulate
filter (95% filter
efficiency level)
particulate aerosols;
time use restrictions
may apply
N95-Particulate
filter (95% filter
efficiency level)
effective against
all particulate
aerosols
HE-High Efficiency Particulate Air filter for powered, air-purifying respirators
*(From page 53 of NIOSH’s “Standard Application Procedures for the Certification of Respirators” Rev. 7/98)
Web Links to Welding & Safety
Standards Organizations
www.ansi.org
(American National Standards Institute)
www.csa.ca
(Canadian Standards Association)
www.cdc.gov/niosh
(National Institute for Occupational Safety &
Health)
www.osha.gov
(Occupational Safety & Health Administration)
www.aws.org
(American Welding Society)
AG -Acid Gas (gas mask only)
CF -Continuous flow
CO -Carbon monoxide
EO -Ethylene oxide
HF -Hydrogen fluoride
MA -Methylamine
OV -Organic vapor
SA -Supplied-air
SD -Sulfur dioxide
AM -Ammonia
CL -Chlorine
CS -Chlorobenzylidene
malononitrile
FM -Formaldehyde
HN -Hydrogen cyanide
MV -Mercury vapor
PD -Pressure demand
SB -Supplied-air
Abrasive Blast
VC -Vinyl chloride
CD -Chlorine dioxide
CN -Chloroacetophenone
DE -Demand
HC -Hydrogen chloride
HS -Hydrogen sulfide
(escape only)
ND -Nitrogen dioxide
PH -Phosphine
SC -Self-contained
Speedglas with Adflo system uses an HE
Particulate Air Filter. An additional OV/SD/CL/HC
cartridge can be added to the HE filter.
Speedglas Fresh-air II SA 9000 system is a
supplied air (SA) respirator.
48
49
Customer Support
If you have any questions about your Speedglas
products, contact Hornell’s Customer Service at:
800-628-9218 or Fax: 330-425-4576. (Canada:
800-676-6930 or Fax: 905-664-1402.)
Speedglas® Lens Warranty
Hornell, Inc. warrants all Speedglas lenses for 24
months from the date of purchase against all
manufacturing defects resulting from materials or
workmanship. This warranty is void in the case of
operator misuse, abuse, or neglect. Read your
instruction manual to avoid certain situations
which could void this warranty (for example,
cracked lenses and lenses covered with weld
spatter are not covered under the warranty policy).
The foregoing warranty shall not apply, and
Hornell, Inc. shall be held harmless and relieved of
any obligation or liability to the buyer, if the
equipment has been repaired or altered in a manner
not authorized by Hornell, including the use of
replacement components not approved by Hornell,
or if the equipment has been subject to abuse,
negligence or accidental mishandling.
Speedglas® With Adflo® Warranty
Hornell, Inc. warrants all Adflo products obtained
hereunder to be free from detects in material and
workmanship in normal service and under normal
conditions for 12 months from the date of delivery.
Speedglas® Fresh-air® II SA 9000
Warranty
®
Hornell, Inc. warrants all Fresh-air products
obtained hereunder to be free from detects in
material and workmanship in normal service and
under normal conditions for 180 days from the
date of delivery.
50
Hornell Individual Supplied Air
Purification System Warranty
Hornell, Inc. warrants all Hornell Individual
Supplied Air Purification System obtained
hereunder to be free from detects in material and
workmanship in normal service and under normal
conditions for 180 days from the date of delivery.
The foregoing warranties are in lieu of all other warranties expressed,
implied, or statutory, including warranty of merchantability or fitness for
a particular purpose.
Warranty Return Procedure
1) Make a photocopy of your proof-ofpurchase; include the serial number of
the product being returned.
2) Call the Hornell Warranty Department toll-free
at 888-773-3345 (Canada: 800-676-6930) to
describe the warranty problem and receive a
warranty return number.
3) Write the warranty return number on
the proof-of-purchase photocopy and fax
to Hornell Warranty Department at
330-487-5326 (Canada: 905-664-1402).
Upon receipt, Hornell will send out a
replacement product that will, in most
cases, arrive the next business day.
Send the original product via UPS third party
billing or a call tag issued by Hornell; clearly
write the warranty return number on the
outside of the package.
Out-Of-Warranty Repairs & Service
For repair pricing and procedures, call the Service,
Repair & Warranty Dept. toll-free: 888-773-3345 or
Fax: 330-487-5326. (Canada: 800-676-6930 or
Fax: 905-664-1402.)
WARNING: These welding safety products must be used only by
qualified persons trained in their use and maintenance and only in strict
accordance with and adherence to the detailed instructions and
precautionary statements provided in the Instruction Manual which
accompanies each product. Failure to comply with these instructions
could result in serious bodily injury or loss of life. Any questions
concerning proper use of these units should be directed to your on-site
training specialist or industrial hygienist.
51
®
Speedglas Lens
Selector Table
Utility
9000F
9000XF
9000V
Light Shade
3
3
3
3
9000X
3
Dark
Shade(s)
10 or 11
10, 11
or 12
10, 11
or 12
9, 10, 11,
12 & 13
9, 10, 11,
12 & 13
Viewing Area 3.57 x 1.68 3.57 x 1.68 4.09 x 2.13 3.57 x 1.68 4.09 x 2.13
inches/mm
91 x 43
91 x 43
104 x 54
91 x 43
104 x 54
Weight, Lens
& Helmet
oz/grams
SideWindows™
Available?
Helmet has
CO2 Exhaust
vents
17.14
17.14
17.39
17.14
17.39
486
486
493
486
493
No
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
04-0012-10 04-0012-10X
or
or
04-0014-10U
or
04-0012-11 04-0012-11X 04-0012-30 04-0012-20
or
or
04-0014-11U
04-0012-12 04-0012-12X
Page Number
12
14
16
18
20
Part #’s
(complete
helmet
with lens)
Hornell reserves the right to make changes in specifications at any time without prior notice.
Speedglas®, Fresh-air®, SideWindows™ and Adflo® are trademarks of Hornell. All
trademarks are property of their respective owners. Speedglas® products are protected by
U.S. Patents 4,039,254; 4,240,709; Re. 29,684; 5,191,468; also protected by international
patents. ©2002 Hornell. Printed in USA. 92-0028-01 Rev. L
HORNELL, INC.
2374 EDISON BLVD. • TWINSBURG, OH 44087 USA
TEL: 800-628-9218 • 330-425-8880 • FAX: 330-425-4576
EMAIL: [email protected] • www.hornell.com
HORNELL, INC. (CANADA)
43 TEAL AVE. UNIT 1 • STONEY CREEK, ONTARIO L8E 3B1
TEL: 800-676-6930 • 905-664-6239 • FAX: 905-664-1402
EMAIL: [email protected] • www.hornell.com

Speedglas Complete Catalog

Transcription

Similar documents

Digital Elite™ Series

welding helmet

The author has no financial interest to disclose. How Many of your

Dirtbike Magazine

Portatile e senza fili, per uno screening di qualità Portatile e senza

Givi V46 reflective decal installation instructions:

Foster barriers with crossed beams produce a thick grid of crossed

Video Sunglasses, Sports HD 720p Wide Angle

Visit our Web-Site at www.starrett-precision.co.uk