OPERATOR`S MANUAL

Transcription

OPERATOR`S MANUAL
OPERATOR’S MANUAL
GD200 GARAGE DOOR OPENER
MODULE SYSTEM APP
This app is optimized for:
iOS versions 9.0 and higher ∙ Android versions 6.0 and higher
For a full list of compatible phones please visit
www.ryobitools.com
Thank you for purchasing your
RYOBI™ Garage Door Opener Module System product
If you need assistance
DO NOT RETURN TO THE STORE
Please contact us at 1-800-525-2579
991000884
3-17-16 (REV:01)
App images may vary.
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
To reduce the risk of injury, do not attempt to use this app
until you have read thoroughly and understand completely
this operator’s manual and the operator’s manual for the
GD200 garage door opener.
Only use the Ryobi Garage Door Opener Module System
App to control garage door openers installed on sectional
doors. Do not use this app to open or close singlepanel garage doors.
Always follow all safety rules recommended by the
manufacturer of your garage door opener, in addition to
all safety rules for the garage door opener attachment
and accessories. Following this rule will reduce the risk
of serious personal injury.
App images may vary.
Devices or features, such as the Ryobi Garage Door
Opener Module System App, that allow you to open and
close the garage without the garage door being in view
should only be used with sectional garage doors.
A monthly test of the device’s functionality is recommended
to ensure reliable performance over time.
Do not use the garage door opener if it is damaged or
broken.
Do not allow children or untrained individuals to operate
the garage door opener.
Do not allow to be used as a toy. Close attention is
necessary when near children.
To avoid death or serious personal injury, stay clear of
the garage door while it is moving.
GETTING STARTED
WARNING:
To reduce the risk of injury to persons – Only enable the
Ryobi Garage Door Opener Module System App feature
when installed with a sectional door.
WARNING:
Devices or features, such as the Ryobi Garage Door
Opener Module System App, that allow you to open and
close the garage without the garage door being in view
should only be used with sectional garage doors.
CREATING AN ACCOUNT
See Figures 1 - 3.
Download the Ryobi Garage Door Opener Module System
App from the App Store or Google Play Store.
Sign up for an account by entering your email address,
creating a password, and setting your security preferences.
NOTE: Press the information icon (
app security preferences.
) for details on the
FIG. 2
Once you have signed up, log into your account using
your email address and password.
FIG. 3
FIG. 1
App images may vary.
GETTING STARTED
WARNING:
WARNING:
To reduce the risk of severe injury or death, make sure your
garage door opener is properly installed before syncing it
to the Ryobi Garage Door Opener Module System App.
ADDING A GARAGE DOOR OPENER
TO YOUR ACCOUNT
Press and hold the Wi-Fi button (for five seconds) until
the Wi-Fi button begins to blink signaling that the garage
door opener is attempting to sync with your phone.
See Figures 4 - 10.
Assemble and mount the garage door opener as
described in the garage door opener manual.
After signing in, press the plus icon (
door opener to your account.
Use extreme care when standing on a ladder. Ensure
someone is holding the ladder on the ground to keep it
stable. Failure to safely use a ladder can cause a fall and
result in death or serious personal injury.
) to add a garage
Sync your garage door opener’s wireless network to your
phone by selecting “RYOBI_GDO_xxx” from the list of
available networks.
Carefully climb up a ladder and open the console door
on the back of your garage door opener.
Wi-Fi
Button
LIGHT
COVER
FIG. 4
FIG. 6
Sync GDO to Phone
You’re going to sync the GDO’s wi-fi
network to your phone. Select the network
RYOBI_GDO_XXX
Then, come back here.
Child can become trapped
in serious injury or death. or pinned under an automatic garage door resulting
• Do not allow children to
walk or run under a closing
door.
• Do not allow children to
operate door opener controls.
• Always keep a closing
door within sight.
• In the event a person is
trapped under the door, push
use the emergency release.
the control button or
• This operator system is
equipped
door could move unexpectedly. with an unattended operation feature. The
Not intended for use with
doors.
single panel garage
Test door opener monthly:
• Refer to Operator’s Manual.
• Use a 1 ½ inch thick object
(or 2 X 4 laid flat) placed
closing door.
on the floor under the
• In the event the door does
reverse upon contact, adjust,
opener.
repair, or replace the
Do not remove or paint over
this label.
Mount this label next to the
wall control.
Mount the wall control out
of the reach of children at
least 5 feet above the floor.
FIG. 5
App images may vary.
Next
FIG. 7
GETTING STARTED
Sync your garage door opener to your home wi-fi network
by selecting your home network from the list of available
networks and entering your password (if applicable).
Name your garage door opener and navigate to the Home
screen or App Navigation Tutorial screen to complete
initial setup.
NOTE: If your network isn’t listed, click “Don’t see your
network listed” for possible explanations.
After the garage door opener has been synced to your
smart phone and home Wi-Fi networks, test the Ryobi
Garage Door Opener Module System App functionality
as described in the next section.
Sync GDO to Home Wi-Fi
Congrats - you’re done!
Now, you’re going to connect your
GDO to your home wi-fi network.
Select this network from the list below,
and put in your password:
Go to the Home Hub
WIRELESS NETWORKS
Don’t see your network listed?
See Tutorial of App
Navigation
FIG. 8
FIG. 10
Rename your hub
Almost done! Now let’s give your
garage door opener a name:
FIG. 9
App images may vary.
HOME SCREEN (FEATURES)
EXPLORE
PROFILE
SETTINGS
STATUS
PRESET
LIGHTS
OPEN
GARAGE DOOR
ICON
CLOSE
GARAGE DOOR
FIG. 11
DESCRIPTION/FUNCTION
Press this icon to access your PROFILE menu. From this menu, you can add a
profile image, change your account settings, and view your activity log.
Press this icon to access the SETTINGS menu. From this menu you can adjust the
settings of the module system app.
Press this icon to CLOSE the garage door.
Press this icon to OPEN the garage door.
Press this icon to EXPLORE the full suite of Garage Door Opener Module System
products.
Press this icon to raise or lower the garage door to a partially open PRESET
position.
Press this icon to turn the garage door opener LIGHTS on and off.
This section of your hub screen shows the position of your garage door and the last
time it was open or shut.
App images may vary.
OPERATION
Before operating the garage door opener, align the safety
sensors and set the door travel limits according to the
GD200 Operator’s Manual.
WARNING:
DO NOT operate the garage door opener unless the
safety sensors are installed and working correctly. Failure
to properly install and ensure that the safety sensors are
working correctly can result in death or serious personal
injury.
WARNING:
RAISING AND LOWERING THE
GARAGE DOOR
See Figures 12 and 13.
WARNING:
To reduce the risk of injury to persons – Only enable the
RYOBI Garage Door Opener Module System App feature
when installed with a sectional door.
Press the up icon (
open position.
) to raise the garage door to the fully
Press the down icon (
fully open position.
) to raise the garage door to the
The effectiveness of the safety sensors included in this
system directly relates to the placement and installation
of the sensors. Incorrect placement or installation could
prevent the sensors from working as intended and result
in death or serious personal injury.
NOTICE:
The garage door will not close unless the safety sensors
are installed, wired, and aligned correctly.
DANGER:
Ensure that the safety sensors are installed and working
properly. Without the proper safety devices in place, a
closing garage door could kill or seriously injure someone
in its path.
FIG. 12
NOTICE:
Do not open or close the garage door using the indoor
keypad, remotes, or phone app until the travel limits have
been properly set. Doing so could cause severe damage
to the garage door or the garage door opener.
FIG. 13
App images may vary.
OPERATION
USING THE PRESET FEATURE
TURNING THE LED LIGHTS ON AND OFF
See Figures 14 and 15.
See Figures 16 and 17.
The garage door opener module system app can be
programmed to raise or lower the garage door to a partially
open preset position.
Touch the light icon ( ) to turn the LED lights, located
beneath the light cover, on and off.
To move your garage door to a partially open position,
press the preset icon ( ).
NOTE: By default, the door will be raised or lowered to
18 in. above the garage floor. The preset height can be
adjusted in the settings ( ) menu as described later in
this section.
NOTE: By default, the LED lights will illuminate for four minutes
after the light icon ( ) is pressed or the motion sensor is
activated. These defaults can be adjusted by selecting “LED
Light” in the settings ( ) menu as described later in this
section.
FIG. 16
FIG. 14
FIG. 17
FIG. 15
App images may vary.
OPERATION
CHECKING BATTERY PACK CHARGE STATUS
INSTALLING MODULES
See Figures 18 and 19.
See Figures 20 - 23.
When a battery pack is installed and the power cord is
plugged in, the garage door operator will begin charging the
battery pack. The charge status of the battery pack can be
seen at the bottom of the home screen.
The garage door opener can power a variety of AC and DC
modules. For a complete list of modules, press the explore
icon ( ) or visit ryobitools.com.
WARNING:
Use only recommended accessories listed on our
website, in this manual, or in addendums. Use of
accessories that are not listed may cause the risk of
personal injury. Instructions for safe use of accessories
are included with the accessory.
8:08 AM
100%
FIG. 18
FIG. 19
FIG. 20
App images may vary.
OPERATION
WARNING:
Ensure modules are properly and securely connected to
their port on the garage door opener. Failure to properly
secure the module can cause it to fall and could result in
serious personal injury or property damage.
Install and secure DC or AC module as described in the
module’s operator’s manual. The garage door opener
will automatically detect most modules and the module
controls will appear at the bottom of the hub screen.
Use the module controls to monitor, activate, and change
module operation.
NOTE: If the RYOBI Garage Door Opener Module System
App does not detect your module, the module controls can
be added manually by selecting “Module Map” from the
profile ( ) menu as described later in this section.
FIG. 21
FIG. 22
App images may vary.
FIG. 23
OPERATION
SETTINGS MENU
See Figure 24 - 25.
From the settings ( ) menu, you can turn notifications on
and off, change the amount of time your LED lights remain
on, turn off the motion sensor, enter and exit vacation mode,
and adjust the preset height for your garage door.
Notification Setting
This setting can be programmed to notify you when the door
is opened or closed, when the door has been open longer
than a specified length of time, and if the door is opened
after a certain time of day.
LED Light Setting
Garage Door Opener
Notifications
Timezone
Central Standard Time
Door Opens
Door Closes
Adjust this setting to change how long the LED lights remain
on.
Door Open Longer Than
Motion Sensor Setting
Door Open After
40min
8:00 pm
Change this setting to turn the motion sensor on and off.
Vacation Mode Setting
Change this setting to enter and exit vacation mode. When in
vacation mode, the garage door opener can only be activated
with the indoor keypad or smart phone app.
Motion Sensor
2 min
Preset Function Setting
To change the preset position of your garage door, select
one of the three existing heights or create a custom height
up to 6 feet above the garage floor.
Away
IN
IN
CM
CM
Height Setting
5 inch
(default)
18 inch (default)
36 inch
Custom
Custom(up
(upto
to66feet)
feet)
FIG. 24
FIG. 25
App images may vary.
OPERATION
PROFILE MENU
Account Settings:
See Figure 26 - 33.
From the account settings screen, you can change your
name, email address, password, security preferences, email
preferences, and who receives app notifications.
From the profile ( ) menu, you can change your profile
name and image, manage account settings, add garage
door openers, view activity logs, view the module map, read
frequently asked questions, and contact customer support.
Add Opener:
Select this option to add multiple garage door openers
to your account using the setup process described in the
Getting Started section.
Activity Log:
The activity log shows each date and time the garage door
opens and closes. To delete the activity log, tap “Clear Log”.
FIG. 26
Garage Door Opener
8:08 AM
100%
FIG. 28
Clear Log
Not Connected
Nov 17, 2015
5:30 PM - Garage Door Opened
6:45 PM - Garage Door Closed
Nov 18, 2015
5:30 PM - Garage Door Opened
ONE + Battery Backup
6:45 PM - Garage Door Closed
status :
Nov 19, 2015
5:30 PM - Garage Door Opened
6:45 PM - Garage Door Closed
FIG. 27
App images may vary.
FIG. 29
OPERATION
Module Map:
Installation Guide:
The module map allows you to see which modules are
installed and in which ports they’re installed. Most modules
will be detected automatically, but others will have to be
added manually by selecting
“Add
Module” and choosing
Bluetooth®
Speaker
the appropriate port or ports.
This option provides a link to the latest version of the GD200
Operator’s Manual and Quick Start Guide.
7
Laser Parking Assist
4
Variable Speed Fan
1
Garage Carbon
Bluetooth® Speaker
Monoxide Alarm
7
2
Laser Parking
Assist
Power
Cord Reel
4
5-6
Variable Speed Fan
1
Port 7
Port 6
Port 5
Garage Carbon
Monoxide Alarm
Power Cord Reel
Port 4
Troubleshooting:
This tab provides a link to suggestions on solving problems
related to installation, connectivity, and operation.
FAQ:
This tab provides a link to answers of our user’s frequently
asked questions.
Support:
The support section has contact information for the customer
support team.
About:
The about section has the terms and conditions for the
garage door opener module system.
Port 1
2
Call our support team
5-6
Port 2
Port 3
Port 7
Port 6
Email our support team
Port 1
FIG. 30
Port 5
FIG. 32
Port 2
Port 4
Port 3
Power Cord Reel
FIG. 33
FIG. 31
13
1
2
Done
App images may vary.