MetaSole

Transcription

MetaSole
German Engineering for British Innovation
InterSole SE
ConSole+
Solar Mounting Systems:
Product Introduction
VarioSole
S Clamp
TriSole
FS10
MetaSole
Company Profile
Basic Data
 Head Office in Cologne
 More than 17 years of experience in the
Mounting Systems for Photovoltaic Modules
 World wide Sales and Distribution
 Continuous development of new mounting
systems
Company History
 1997 Foundation as Econergy GmbH
 2004 Takeover by Ubbink BV, NL
 Change of Name: Ubbink Econergy Solar GmbH
 2005 Integration into the Centrosolar Group
 2006 Development into the European Market
 2007 Expansion to France
 2009 Change of Name: from Ubbink Econergy Solar
GmbH to Renusol GmbH
Renusol in Europe
New Markets
Czech
Republic
Slowakia
Slowenia
Bulgaria
Renusol: UK representatives
Huw Cooper - Sales Manager, UK and Ireland
Jason Mccabe IEng MEIHead ofApplication Engineering , UK and Ireland Technical Support
Thomas Weile - Account Manager, South UK, Spain and ROW
Darren Painter– Uk Technicial Applications support
Products
 Excellent and flexible applicable Products
 Easy Installation and Mounting
 Suitable for all standard Modules
 Patented Mounting Systems
 TÜV-Certified
 BRE MCS 012 pitched roofs ( 2014 )
 Durable and approved Materials
 Shared Technology Platform for
InterSole, VarioSole TriSole S Clamp & MetaSole
 VarioSole
 MetaSole
 InterSole SE
 TriSole
 TerraSole
 ConSole +
 S Clamp
 FS10 NEW 2014
Commercial and Industrial
PV mounting systems:
Pitch roofs
Flat roofs
Metal sheet
Standing Seam
Ground mounting
Applications
VarioSole SE singlelayer portrait
VarioSole SE twolayer landscape
MetaSole
MetaSole
MetaSole
MetaSole is a complete mounting system suitable
for mounting all marketable framed modules with a
frame height of 30-51mm, and on pitched
roofs from 3 - 45 degrees with trapezoidal
steel/aluminium sheet.
MetaSole
MetaSole can be used with trapezoidal sheet
Aluminium or steel profiles with a thickness of 0.4
to 1.5mm and with a rib/crown width of 20 (min.)
Pitched roof: MetaSole
MetaSole
MetaSole
The special clamp
bases of the MetaSole
system are screwed
directly onto the rib
of the sheet and offers
Waterproof mounting
through EPDM rubber
on the underside of
the base clamp
Height adjustable end and middle clamps
are slid or clipped onto the clamp bases.
These provide secure support for the PV
module.
MetaSole
SRT Scotland installation of
the now famous 48 Kwp
Pyramid building at the
survey Scotland HQ
Edinburgh.
Nominated for the Solar Power
Award at the Solar Energy UK
MetaSole
Largest UK MetaSole
installation to date.
2Mw which is at the
Wolseley Training
Academy and
warehouse HQ
MetaSole
MG Renewables 500Kwp
project at FUCHS processing
factory.
Following a previous Segen
commercial conference.
MetaSole
Direct Mounting on
Metal Profile Roofs
 Easy mounting of PV modules on
trapezoidal metal panels
 Usage in professional projects
 Low material usage for best costbenefit ratio
 Sheet thickness minimum 0.4 mm
 Logistic costs reduced due to smallsize and pre-assembled parts
MetaSole
System Advantages
 Universal mounting system with only 4 components
 Low storage costs due to small, light and variable components
 Optimized logistics, short-term dispatch to construction site
possible
 Variable mounting system for module frame heights of 30 51mm
 Fastening on the roof using normal self-drilling screws, no
pre-drilling and no drilling template required
MetaSole
FS10
FS10 East / West flat roof Concept
FS10
FS10
FS10
Features:
•
•
•
•
•
East - West concept
10o inclination
Exceptionally low ballast requirement
Minimum components
Fast installation time – due to 4 key
components
ConSole+
ConSole+
Flat Roof
Applications
ConSole+
The ConSole+ is a mounting
system developed for flat
roofs with low bearing
Capacities and can be used
For ground mount applications.
It has all the benfits of the consule product series but comes
preset at an angle of 15o for minimum distance between rows.
With the optional streamliner wind deflector the ConSole+
uses up to 50% less ballast in large PVfields, making it an
excellent choice for flat roofs and ground mount applications.
ConSole+
The ConSole is placed on the
roof structure or at ground level
and is weighed down using the
respective ballast weight.
Taken into account are:
 Height of building
 The location
 The local wind conditions
 State of the foundations
 Roof Area
ConSole+
Below is a typical layout of the ConSole used on a flat roof.
Consoles which are in the corner and edge zones are exposed,
the others are shielded. The exposed (grey) consoles have a
greater ballast load than the shielded consoles.
ConSole+
System Components
The U profile fits to the whole
spacing of the module. This is
then connected to the ConSole.
Flat roof: ConSole+
Leading product for flat roof mounting of modules
ConSole+
4 simple steps to mounting:
The ConSole unit is
placed in position and
the calculated required
amount of ballast is
added.
ConSole+
4 simple steps to mounting:
The aluminum profiles are
bolted to the holes at the rear
of the module .
Finally, the self-drilling fixing is
attached to the edge of the
ConSole unit.
ConSole+
ConSole+
Advantages
ConSole+
Preset 15o angle (minimum distance between rows)
Cost effective on roof or ground mount solution
Very low ballasting
Optional streamliner +(wind deflector) for ballast
reduction
on the roof edge
 Speedy installation time (minimum fastenings
required)
TriSole
TriSole
The TriSole system is ideal for installing solar systems
on flat roofs, Groundmounting, Corrugated and
Trapezoidal sheet or for mounting over-sized framed PV
modules.
The TriSole triangular mounting system can be mounted
at different elevation angles on flat roofs of both old
and new buidlings.
The system is fastened and /or secured with screw
Mounts or ballasting, depending on local conditions.
TriSole Configuration
TriSole
Product Overview
Existing product line

TriSole with 20-30° variable angle and adjustable frame height
Product extension

Now available 8°, 10° -15°, 20° -30°, 35° -45°
TriSole
TriSole
TriSole
Advantages
 Speedy installation time (minimum fastenings required)
Minimum components
Universal end and middle clamps used with MetaSole ,
VarioSole and InterSole SE
Aesthetically pleasing
S Clamp: Standing Seam Mounting Solution
S Clamp
Standing Seam Mounting Solution
S Clamp
Traditionally clamps are
placed directly from the
standing seam to the
module. However you are
limited with this format
and clamping dictates the
layout of the PV field.
By using a rail system you
can overcome this obstacle
and have more scope to
plan a PV field.
S Clamp
Standing Seam Mounting Solution
S Clamp for all standing
seam classic profiles for
Bemo, Kalzip and
Plannja.
S Clamp: Standing Seam Mounting Solution
System Advantages
 Shared platform technology with Variosole, Trisole, Intersole and Renosul
Universal Mounting brackets.
 Minimum components
 Fast installation time
 Light weight system
 System can be mounted vertically and horizontally
 Superior fixing hold against extreme wind speeds
 Approved for use with Kalzip, Bemo, & Plannja.
TerraSole
TerraSole
Material
Complete hot – dip –
galvanized DIN EN ISO 1461
Available in 20 -25 & 30*
inclination.
Standard tables available
2 x rows of 6 modules (12 x
module)
2 x rows of 12 module (24 x
module)
4 x 12 module (48 x module)
4 x 24 module (96 x modules)
Over 100Kwp
Table can be configured to
specific requirements.
Renusol accessories
Brackets for mini inverters /
optimisers.
To fit INSE, VS, TS,
all of the ConSole range.
UK Accessories Development
Renusol accessories
Anti-theft screws
fully useable with
Renusol End Clamps
and Mid Clamps.
Supplied with fixing
tool or available as
an optional extra.
Services & Solutions
Webconfigurator
• Plant planning
• Bid proposal management
• Import into SAP
• Extension with static calculation
Goal:
process optimization
http://web.renusol.com
InterSole SE
ConSole+
Any questions?
ConSole
VarioSole
TriSole
MetaSole
Jason Mccabe IEng MEI