15-7230.00 - LaMettry`s Collision
Transcription
15-7230.00 - LaMettry`s Collision
LaMETTRY'S COLLISION AUDUBON ROAD CHANHASSEN, MN BEFORE YOU BEGIN - REQUIRED MATERIALS AND EQUIPMENT 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. DRAWING INDEX PROPER GEOTECHNICAL SOIL EVALUATION BY A QUALIFIED ENGINEER OR SOIL SCIENTIST TO DETERMINE SUITABILITY OF STRUCTURAL INSTALLATION OSHA COMPLIANCE CULTEC WARNING TAPE, OR EQUIVALENT ASSURANCES FROM LOCAL UTILITIES THAT NO UNDERGROUND GAS, ELECTRICAL OR OTHER POTENTIALLY DANGEROUS PIPELINES OR CONDUITS ARE ALREADY BURIED AT THE SITE ACCEPTABLE 1- 2 INCH (25 - 51 MM) WASHED, CRUSHED STONE AS DETAILED IN CULTEC'S INSTALLATION INSTRUCTIONS. CLEANLINESS OF STONE TO BE VERIFIED BY ENGINEER. ACCEPTABLE FILL MATERIAL AS SHOWN IN CULTEC'S INSTALLATION INSTRUCTIONS. CULTEC NO. 410™ FILTER FABRIC OR EQUIVALENT NON-WOVEN FILTER FABRIC ALL CULTEC CHAMBERS AND ACCESSORIES AS SPECIFIED IN THE ENGINEER'S PLANS INCLUDING CULTEC NO. 410™ FILTER FABRIC, CULTEC STORMFILTER® AND CULTEC NO. 20L™ POLYETHYLENE LINER, WHERE APPLICABLE. CHECK CULTEC CHAMBERS FOR DAMAGE PRIOR TO INSTALLATION. DO NOT USE DAMAGED CULTEC CHAMBERS, CONTACT YOUR SUPPLIER IMMEDIATELY TO REPORT DAMAGE OR PACKING-LIST DISCREPANCIES. RECIPROCATING SAW OR ROUTER STONE BUCKET STONE CONVEYOR AND/OR TRACKED EXCAVATOR TRANSIT OR LASER LEVEL MEASURING DEVICE COMPACTION EQUIPMENT WITH MAXIMUM GROSS VEHICLE WEIGHT OF 12,000 LBS (5,440 KGS). VIBRATORY ROLLERS MAY ONLY BE USED ON THE STONE BASE PRIOR TO THE INSTALLATION OF CHAMBERS. REQUIREMENTS FOR CULTEC CHAMBER SYSTEM INSTALLATIONS TITLE SHEET NO. NORTH SYSTEM LAYOUT SHEET 1 OF 6 MIDDLE SYSTEM LAYOUT SHEET 2 OF 6 2. SOUTH SYSTEM LAYOUT SHEET 3 OF 6 SYSTEM CALCULATIONS SHEET 4 OF 6 3. 4. 150XLHD DETAIL SHEET 5 OF 6 SEPARATOR ROW DETAIL SHEET 6 OF 6 1. 5. 6. 7. 8. PROJECT INFORMATION PROJECT NO: CULTEC SALES REP: 9. 10. 15-7230 JOHN DITULLIO (203)-775-4416 EXT. 105 475-289-7105 11. [email protected] CULTEC CAD TECH: DAN GERA 12. (203)-775-4416 EXT. 129 13. [email protected] COMMENTS: TM CULTEC, Inc. Subsurface Stormwater Management Systems CULTEC P.O. Box 280 878 Federal Road Brookfield, CT 06804 www.cultec.com PH: (203) 775-4416 PH: (800) 4-CULTEC FX: (203) 775-1462 [email protected] 14. INSTALLING CONTRACTORS ARE EXPECTED TO COMPREHEND AND USE THE MOST CURRENT INSTALLATION INSTRUCTIONS PRIOR TO BEGINNING A SYSTEM INSTALLATION. IF THERE IS ANY QUESTION AS TO WHETHER YOU POSSESS THE MOST CURRENT INSTRUCTIONS, CONTACT CULTEC AT (203) 775-4416 OR VISIT WWW.CULTEC.COM. CONTACT CULTEC AT LEAST THIRTY DAYS PRIOR TO SYSTEM INSTALLATION TO ARRANGE FOR A PRE-CONSTRUCTION MEETING. ALL CULTEC SYSTEM DESIGNS MUST BE CERTIFIED BY A REGISTERED PROFESSIONAL ENGINEER. USE CULTEC INSTALLATION INSTRUCTIONS AS A GUIDELINE ONLY FOR MINIMUM/MAXIMUM REQUIREMENTS. ACTUAL DESIGN MAY VARY. REFER TO APPROVED CONSTRUCTION DRAWINGS FOR JOB-SPECIFIC DETAILS. BE SURE TO FOLLOW THE ENGINEER'S DRAWINGS AS YOUR PRIMARY GUIDE. THE FOUNDATION STONE SHALL BE LEVEL AND COMPACTED PRIOR TO CHAMBER INSTALLATION. OVERLAPPING RIB CONNECTIONS OF CHAMBERS SHALL BE FULLY SHOULDERED PRIOR TO STONE PLACEMENT. CENTER TO CENTER SPACING SHALL BE CHECKED AND MAINTAINED THROUGHOUT INSTALLATION PROCESS. ANY DISCREPANCIES WITH THE SYSTEM SUB-GRADE SOIL'S BEARING CAPACITY MUST BE REPORTED TO THE DESIGN ENGINEER. FILTER FABRIC MUST BE USED AS SPECIFIED IN THE ENGINEER'S DRAWINGS. CULTEC REQUIRES THE CONTRACTOR TO REFER TO CULTEC'S INSTALLATION INSTRUCTIONS CONCERNING VEHICULAR TRAFFIC. RESPONSIBILITY FOR PREVENTING VEHICLES THAT EXCEED CULTEC'S REQUIREMENTS FROM TRAVELING ACROSS OR PARKING OVER THE CHAMBER SYSTEM LIES SOLELY WITH THE CONTRACTOR THROUGHOUT THE ENTIRE SITE CONSTRUCTION PROCESS. THE PLACEMENT OF WARNING TAPE, TEMPORARY FENCING, AND/OR APPROPRIATELY LOCATED SIGNS IS HIGHLY RECOMMENDED. IMPRINTED WARNING TAPE IS AVAILABLE FROM CULTEC. FOR ACCEPTABLE VEHICLE LOAD INFORMATION, REFER TO CULTEC INSTALLATION INSTRUCTIONS. TRAFFIC OF INSTALLATION EQUIPMENT OR OTHER VEHICULAR TRAFFIC OVER TOP OF THE CULTEC STORMWATER SYSTEM IS STRICTLY RESTRICTED AND PROHIBITED UNTIL SATISFACTORY COVER AND COMPACTION IS ACHIEVED ACCORDING TO CULTEC'S MANUFACTURER INSTALLATION INSTRUCTIONS. EROSION AND SEDIMENT-CONTROL MEASURES MUST MEET LOCAL CODES AND THE DESIGN ENGINEER'S SPECIFICATIONS THROUGHOUT THE ENTIRE SITE CONSTRUCTION PROCESS. CULTEC SYSTEMS MUST BE DESIGNED AND INSTALLED IN ACCORDANCE WITH CULTEC'S MINIMUM REQUIREMENTS. FAILURE TO DO SO WILL VOID THE LIMITED WARRANTY. CONTACT CULTEC, INC. AT 203-775-4416 WITH ANY QUESTIONS OR FURTHER CLARIFICATION OF REQUIREMENTS. THIS DRAWING WAS PREPARED TO SUPPORT THE DESIGN ENGINEER FOR THE PROPOSED SYSTEM. IT IS THE ULTIMATE RESPONSIBILITY OF THE DESIGN ENGINEER TO ASSURE THAT THE STORMWATER SYSTEM'S DESIGN IS IN FULL COMPLIANCE WITH ALL APPLICABLE LAWS AND REGULATIONS. IT IS THE DESIGN ENGINEER'S RESPONSIBILITY TO ENSURE THAT THE CULTEC PRODUCTS ARE DESIGNED IN ACCORDANCE WITH CULTEC'S MINIMUM REQUIREMENTS. CULTEC INC. DOES NOT APPROVE PLANS, SIZING, OR SYSTEM DESIGNS. THE DESIGNING ENGINEER IS RESPONSIBLE FOR ALL DESIGN DECISIONS. 95.00' [28.96 m] 6.00' [1.83 m] WIDE POLYLINER BENEATH FEED CONNECTORS 3.25' [0.99 m] CENTER-TO-CENTER (6" SPACING BETWEEN ROWS) CULTEC No. 20L POLYETHYLENE LINER TO BE PLACED UNDER ALL CHAMBERS UTILIZING INTERNAL MANIFOLD FEATURE AND UNDER ALL INLET/OUTLET PIPES HVLV FC-24 FEED CONNECTOR INV. = 946.50 47.00' [14.33 m] INV. = 946.00 PROPOSED 10" PVC HIGH-FLOW BYPASS PROPOSED 12" PVC STM (PER DRAINAGE PLAN) CBMH A6 (PER DRAINAGE PLAN) CBMH D1 (PER DRAINAGE PLAN) PROPOSED 12" PVC STM (PER DRAINAGE PLAN) INSPECTION PORT (SEE DETAIL) 10.00' [3.05 m] WIDE POLYLINER BENEATH INLET/OUTLET PIPES SEPARATOR ROW (SEE DETAIL) INV. = 946.00 CULTEC STORMWATER MANAGEMENT SYSTEM TOTAL STORAGE PROVIDED: 6,616 c.f. NORTH SYSTEM LAYOUT DETAIL *SYSTEM INSTALLED REQUIRING TYPICAL STONE AMOUNTS OF 6 INCHES BELOW AND ABOVE CHAMBERS AND A 1 FT. [12 INCH] BORDER SURROUNDING 4 OZ. NON-WOVEN FILTER FABRIC AROUND STONE. TOP AND SIDES ARE MANDATORY; BOTTOM PER ENGINEER'S DESIGN PREFERENCE NOTE: ALL EXTERNAL SYSTEM STRUCTURES, INLET/OUTLET PIPES, AND PROPOSED ELEVATIONS MUST BE DESIGNED AND APPROVED BY ENGINEER. ALL SYSTEM ELEVATIONS PROVIDED MUST BE VERIFIED BY THE DESIGN ENGINEER AND THE DESIGN ENGINEER MUST ENSURE CHAMBER BURIAL REQUIREMENTS ARE MET. 1 - 2 INCH [25- 51 mm] DIA. WASHED, CRUSHED STONE RECHARGER 150XLHD HEAVY DUTY CHAMBER IN SEPARATOR ROW CONFIGURATION PAVEMENT OR FINISHED GRADE MIN. 95% COMPACTED FILL LEGEND NOTE: PROPOSED ELEVATIONS ONLY. DESIGN ENGINEER MUST APPROVE ALL SYSTEM ELEVATIONS 12.0' [3.65m] MAX. BURIAL DEPTH CULTEC HVLV FC-24 FEED CONNECTOR WHERE SPECIFIED 8.0" [204 mm] MIN.FOR PAVED 10.0" [254 mm] MIN.FOR UNPAVED MATERIALS LIST RECHARGER 150XLSHD STARTER 14 PIECES RECHARGER 150XLSHD STARTER TOP OF STONE ELEVATION = 948.04 6.0" [152 mm] MIN. TOP OF CHAMBER ELEVATION = 947.54 RECHARGER 150XLIHD INTERMEDIATE 98 PIECES RECHARGER 150XLEHD END 14 PIECES HVLV FC-24 FEED CONNECTORS 28 PIECES RECHARGER 150XLIHD INTERMEDIATE RECHARGER 150XLEHD END 10" HIGH-FLOW BYPASS INV. = 946.50 12" STM INLET PIPE INV. = 946.00 12" STM OUTLET PIPE INV. = 946.00 18.5" [470 mm] BOTTOM OF CHAMBER ELEVATION = 946.00 6.0" [152 mm] MIN. BOTTOM OF STONE ELEVATION = 945.50 5 ROLLS CULTEC NO. 20L POLYETHYLENE LINER 100 LINEAL FEET 1 1/2 - 2 INCH DIAMETER BROKEN STONE 409 TONS CULTEC NO. 410 FILTER FABRIC 7.5' x 300' HVLV FC-24 FEED CONNECTORS CULTEC NO. 20L POLYETHYLENE LINER 12.0" [305 mm] MIN. STONE BORDER SEPARATOR ROWS MATERIALS CULTEC NO. 410 FILTER FABRIC 7.5' x 300' .3 ROLLS TM .3 Subsurface Stormwater Management Systems CULTEC DESIGN ENGINEER RESPONSIBLE FOR ENSURING THE REQUIRED BEARING CAPACITY OF SUB-GRADE SOILS (TYP.) NORTH SYSTEM CROSS-SECTION DETAIL ROLLS CULTEC, Inc. P.O. Box 280 878 Federal Road Brookfield, CT 06804 www.cultec.com 39.0" [991 mm] NON-WOVEN GEOTEXTILE WOVEN GEOTEXTILE CLASS 1 WOVEN GEOTEXTILE 7.5' x 300' 33.0" [838 mm] CULTEC NO. 20L POLYETHYLENE LINER TO BE PLACED BENEATH HVLV FC-24 FEED CONNECTORS WHEN UTILIZING INTERNAL MANIFOLD AND ALL INLET PIPES PH: (203) 775-4416 PH: (800) 4-CULTEC FX: (203) 775-1462 [email protected] THIS DRAWING WAS PREPARED TO SUPPORT THE DESIGN ENGINEER FOR THE PROPOSED SYSTEM. IT IS THE ULTIMATE RESPONSIBILITY OF THE DESIGN ENGINEER TO ASSURE THAT THE STORMWATER SYSTEM'S DESIGN IS IN FULL COMPLIANCE WITH ALL APPLICABLE LAWS AND REGULATIONS. IT IS THE DESIGN ENGINEER'S RESPONSIBILITY TO ENSURE THAT THE CULTEC PRODUCTS ARE DESIGNED IN ACCORDANCE WITH CULTEC'S MINIMUM REQUIREMENTS. CULTEC INC. DOES NOT APPROVE PLANS, SIZING, OR SYSTEM DESIGNS. THE DESIGNING ENGINEER IS RESPONSIBLE FOR ALL DESIGN DECISIONS. LaMETTRY'S COLLISION AUDUBON ROAD CHANHASSEN, MN NORTH SYSTEM SHEET CULTEC RECHARGER® 150XLHD PROJECT NO: 15-7230.00 DATE: 6/18/15 DESIGNED BY: DPG DRAWN BY: DPG SCALE: SHEET NO: 1 OF 6 N.T.S. STMH A4 (PER DRAINAGE PLAN) INV.= 946.50 PROPOSED 12" PVC STM (PER DRAINAGE PLAN) PROPOSED 10" PVC HIGH-FLOW BYPASS SEPARATOR ROW (SEE DETAIL) INV.= 946.50 CBMH C1 (PER DRAINAGE PLAN) PROPOSED 12" PVC STM (PER DRAINAGE PLAN) INSPECTION PORT (SEE DETAIL) INV.= 946.00 56.75' [17.30 m] 1.00' [0.30 m] STONE BORDER CULTEC STORMWATER MANAGEMENT SYSTEM TOTAL STORAGE REQUIRED: 5,366 c.f. TOTAL STORAGE PROVIDED: 6,262 c.f. CULTEC No. 20L POLYETHYLENE LINER TO BE PLACED UNDER ALL CHAMBERS UTILIZING INTERNAL MANIFOLD FEATURE AND UNDER ALL INLET/OUTLET PIPES 6.00' [1.83 m] WIDE POLYLINER BENEATH FEED CONNECTORS 3.25' [0.99 m] CENTER-TO-CENTER (6" SPACING BETWEEN ROWS) (STORAGE PROVIDED IN CHAMBERS: 3,273 c.f.) (STORAGE PROVIDED IN STONE: 2,989 c.f.) *SYSTEM INSTALLED REQUIRING TYPICAL STONE AMOUNTS OF 6 INCHES BELOW AND ABOVE CHAMBERS AND A 1 FT. [12 INCH] BORDER SURROUNDING 74.50' [22.71 m] NOTE:*ALL EXTERNAL SYSTEM STRUCTURES, INLET/OUTLET PIPES, AND PROPOSED ELEVATIONS MUST BE DESIGNED AND APPROVED BY ENGINEER. ALL SYSTEM ELEVATIONS PROVIDED MUST BE VERIFIED BY THE DESIGN ENGINEER AND THE DESIGN ENGINEER MUST ENSURE CHAMBER BURIAL REQUIREMENTS ARE MET. 4 OZ. NON-WOVEN FILTER FABRIC AROUND STONE. TOP AND SIDES ARE MANDATORY; BOTTOM PER ENGINEER'S DESIGN PREFERENCE NORTH SYSTEM LAYOUT DETAIL LEGEND MATERIALS LIST 1 - 2 INCH [25- 51 mm] DIA. WASHED, CRUSHED STONE RECHARGER 150XLHD HEAVY DUTY CHAMBER IN SEPARATOR ROW CONFIGURATION PAVEMENT OR FINISHED GRADE MIN. 95% COMPACTED FILL RECHARGER 150XLSHD STARTER 17 PIECES RECHARGER 150XLIHD INTERMEDIATE 85 PIECES RECHARGER 150XLSHD STARTER NOTE: PROPOSED ELEVATIONS ONLY. DESIGN ENGINEER MUST APPROVE ALL SYSTEM ELEVATIONS 12.0' [3.65m] MAX. BURIAL DEPTH CULTEC HVLV FC-24 FEED CONNECTOR WHERE SPECIFIED 8.0" [204 mm] MIN.FOR PAVED 10.0" [254 mm] MIN.FOR UNPAVED RECHARGER 150XLIHD INTERMEDIATE TOP OF STONE ELEVATION = 948.04 RECHARGER 150XLEHD END 17 PIECES HVLV FC-24 FEED CONNECTORS 15 PIECES 5 ROLLS CULTEC NO. 410 FILTER FABRIC 7.5' x 300' CULTEC NO. 20L POLYETHYLENE LINER 65 LINEAL FEET 1 1/2 - 2 INCH DIAMETER BROKEN STONE 387 TONS RECHARGER 150XLEHD END HVLV FC-24 FEED CONNECTORS ROLLS 18.5" [470 mm] 6.0" [152 mm] MIN. CULTEC NO. 20L POLYETHYLENE LINER SEPARATOR ROWS MATERIALS .3 12" STM OUTLET PIPE INV. = 946.00 10" STM HIGH-FLOW INV. = 946.50 12" STM INLET PIPE INV. = 946.00 BOTTOM OF CHAMBER ELEVATION = 946.00 BOTTOM OF STONE ELEVATION = 945.50 STONE BORDER CULTEC NO. 410 FILTER FABRIC 7.5' x 300' 6.0" [152 mm] MIN. TOP OF CHAMBER ELEVATION = 947.54 12.0" [305 mm] MIN. 33.0" [838 mm] DESIGN ENGINEER RESPONSIBLE FOR ENSURING THE REQUIRED BEARING CAPACITY OF SUB-GRADE SOILS (TYP.) NON-WOVEN GEOTEXTILE WOVEN GEOTEXTILE CLASS 1 WOVEN GEOTEXTILE 7.5' x 300' TM .3 Subsurface Stormwater Management Systems CULTEC P.O. Box 280 878 Federal Road Brookfield, CT 06804 www.cultec.com MIDDLE SYSTEM CROSS-SECTION DETAIL ROLLS CULTEC, Inc. PH: (203) 775-4416 PH: (800) 4-CULTEC FX: (203) 775-1462 [email protected] THIS DRAWING WAS PREPARED TO SUPPORT THE DESIGN ENGINEER FOR THE PROPOSED SYSTEM. IT IS THE ULTIMATE RESPONSIBILITY OF THE DESIGN ENGINEER TO ASSURE THAT THE STORMWATER SYSTEM'S DESIGN IS IN FULL COMPLIANCE WITH ALL APPLICABLE LAWS AND REGULATIONS. IT IS THE DESIGN ENGINEER'S RESPONSIBILITY TO ENSURE THAT THE CULTEC PRODUCTS ARE DESIGNED IN ACCORDANCE WITH CULTEC'S MINIMUM REQUIREMENTS. CULTEC INC. DOES NOT APPROVE PLANS, SIZING, OR SYSTEM DESIGNS. THE DESIGNING ENGINEER IS RESPONSIBLE FOR ALL DESIGN DECISIONS. 39.0" [991 mm] CULTEC NO. 20L POLYETHYLENE LINER TO BE PLACED BENEATH HVLV FC-24 FEED CONNECTORS WHEN UTILIZING INTERNAL MANIFOLD AND ALL INLET PIPES LaMETTRY'S COLLISION AUDUBON ROAD CHANHASSEN, MN MIDDLE SYSTEM SHEET CULTEC RECHARGER® 150XLHD PROJECT NO: 15-7230.00 DATE: 6/18/15 DESIGNED BY: DPG DRAWN BY: DPG SCALE: SHEET NO: 2 OF 6 N.T.S. 76.25' [23.24 m] INSPECTION PORT (SEE DETAIL) 3.25' [0.99 m] CENTER-TO-CENTER (6" SPACING BETWEEN ROWS) SEPARATOR ROW (SEE DETAIL) INV. = 937.50 33.50' [10.21 m] STMH A1 (PER DRAINAGE PLAN) 12" RCP (PER DRAINAGE PLAN) 6.00' [1.83 m] WIDE POLYLINER BENEATH FEED CONNECTORS INV. = 938.00 INV. = 937.50 HVLV FC-24 FEED CONNECTOR PROPOSED 10" PVC HIGH-FLOW BYPASS CULTEC No. 20L POLYETHYLENE LINER TO BE PLACED UNDER ALL CHAMBERS UTILIZING INTERNAL MANIFOLD FEATURE AND UNDER ALL INLET/OUTLET PIPES PROPOSED 12" PVC STM (PER DRAINAGE PLAN) CBMH B1 (PER DRAINAGE PLAN) CULTEC STORMWATER MANAGEMENT SYSTEM TOTAL STORAGE PROVIDED: 6,616 c.f. SOUTH SYSTEM LAYOUT DETAIL *SYSTEM INSTALLED REQUIRING TYPICAL STONE AMOUNTS OF 6 INCHES BELOW AND ABOVE CHAMBERS AND A 1 FT. [12 INCH] BORDER SURROUNDING NOTE: ALL EXTERNAL SYSTEM STRUCTURES, INLET/OUTLET PIPES, AND PROPOSED ELEVATIONS MUST BE DESIGNED AND APPROVED BY ENGINEER. ALL SYSTEM ELEVATIONS PROVIDED MUST BE VERIFIED BY THE DESIGN ENGINEER AND THE DESIGN ENGINEER MUST ENSURE CHAMBER BURIAL REQUIREMENTS ARE MET. 4 OZ. NON-WOVEN FILTER FABRIC AROUND STONE. TOP AND SIDES ARE MANDATORY; BOTTOM PER ENGINEER'S DESIGN PREFERENCE 1 - 2 INCH [25- 51 mm] DIA. WASHED, CRUSHED STONE RECHARGER 150XLHD HEAVY DUTY CHAMBER IN SEPARATOR ROW CONFIGURATION LEGEND MATERIALS LIST RECHARGER 150XLRHD STAND ALONE RECHARGER 150XLSHD STARTER 22 PIECES RECHARGER 150XLIHD INTERMEDIATE 22 PIECES RECHARGER 150XLIHD INTERMEDIATE 2 PIECES RECHARGER 150XLEHD END 22 PIECES HVLV FC-24 FEED CONNECTORS 21 PIECES 3 ROLLS CULTEC NO. 20L POLYETHYLENE LINER 100 LINEAL FEET 1 1/2 - 2 INCH DIAMETER BROKEN STONE 238 TONS CULTEC NO. 410 FILTER FABRIC 7.5' x 300' RECHARGER 150XLSHD STARTER MIN. 95% COMPACTED FILL NOTE: PROPOSED ELEVATIONS ONLY. DESIGN ENGINEER MUST APPROVE ALL SYSTEM ELEVATIONS ROLLS TM .3 Subsurface Stormwater Management Systems CULTEC 6.0" [152 mm] MIN. 10" HIGH-FLOW BYPASS INV. = 938.00 12" STM INLET PIPE INV. = 937.50 12" STM OUTLET PIPE INV. = 937.50 RECHARGER 150XLEHD END 18.5" [470 mm] BOTTOM OF CHAMBER ELEVATION = 937.50 6.0" [152 mm] MIN. BOTTOM OF STONE ELEVATION = 937.00 HVLV FC-24 FEED CONNECTORS CULTEC NO. 20L POLYETHYLENE LINER 12.0" [305 mm] MIN. NON-WOVEN GEOTEXTILE 33.0" [838 mm] 39.0" [991 mm] CULTEC NO. 20L POLYETHYLENE LINER TO BE PLACED BENEATH HVLV FC-24 FEED CONNECTORS WHEN UTILIZING INTERNAL MANIFOLD AND ALL INLET PIPES DESIGN ENGINEER RESPONSIBLE FOR ENSURING THE REQUIRED BEARING CAPACITY OF SUB-GRADE SOILS (TYP.) SOUTH SYSTEM CROSS-SECTION DETAIL ROLLS CULTEC, Inc. P.O. Box 280 878 Federal Road Brookfield, CT 06804 www.cultec.com 8.0" [204 mm] MIN.FOR PAVED 10.0" [254 mm] MIN.FOR UNPAVED RECHARGER 150XLIHD INTERMEDIATE WOVEN GEOTEXTILE CLASS 1 WOVEN GEOTEXTILE 7.5' x 300' CULTEC HVLV FC-24 FEED CONNECTOR WHERE SPECIFIED TOP OF CHAMBER ELEVATION = 939.04 SEPARATOR ROWS MATERIALS .3 12.0' [3.65m] MAX. BURIAL DEPTH TOP OF STONE ELEVATION = 939.54 STONE BORDER CULTEC NO. 410 FILTER FABRIC 7.5' x 300' PAVEMENT OR FINISHED GRADE PH: (203) 775-4416 PH: (800) 4-CULTEC FX: (203) 775-1462 [email protected] THIS DRAWING WAS PREPARED TO SUPPORT THE DESIGN ENGINEER FOR THE PROPOSED SYSTEM. IT IS THE ULTIMATE RESPONSIBILITY OF THE DESIGN ENGINEER TO ASSURE THAT THE STORMWATER SYSTEM'S DESIGN IS IN FULL COMPLIANCE WITH ALL APPLICABLE LAWS AND REGULATIONS. IT IS THE DESIGN ENGINEER'S RESPONSIBILITY TO ENSURE THAT THE CULTEC PRODUCTS ARE DESIGNED IN ACCORDANCE WITH CULTEC'S MINIMUM REQUIREMENTS. CULTEC INC. DOES NOT APPROVE PLANS, SIZING, OR SYSTEM DESIGNS. THE DESIGNING ENGINEER IS RESPONSIBLE FOR ALL DESIGN DECISIONS. LaMETTRY'S COLLISION AUDUBON ROAD CHANHASSEN, MN SOUTH SYSTEM SHEET CULTEC RECHARGER® 150XLHD PROJECT NO: 15-7230.00 DATE: 6/18/15 DESIGNED BY: DPG DRAWN BY: DPG SCALE: SHEET NO: 3 OF 6 N.T.S. NORTH SYSTEM CALCULATIONS TM CULTEC, Inc. Subsurface Stormwater Management Systems CULTEC P.O. Box 280 878 Federal Road Brookfield, CT 06804 www.cultec.com PH: (203) 775-4416 PH: (800) 4-CULTEC FX: (203) 775-1462 [email protected] MIDDLE SYSTEM CALCULATIONS THIS DRAWING WAS PREPARED TO SUPPORT THE DESIGN ENGINEER FOR THE PROPOSED SYSTEM. IT IS THE ULTIMATE RESPONSIBILITY OF THE DESIGN ENGINEER TO ASSURE THAT THE STORMWATER SYSTEM'S DESIGN IS IN FULL COMPLIANCE WITH ALL APPLICABLE LAWS AND REGULATIONS. IT IS THE DESIGN ENGINEER'S RESPONSIBILITY TO ENSURE THAT THE CULTEC PRODUCTS ARE DESIGNED IN ACCORDANCE WITH CULTEC'S MINIMUM REQUIREMENTS. CULTEC INC. DOES NOT APPROVE PLANS, SIZING, OR SYSTEM DESIGNS. THE DESIGNING ENGINEER IS RESPONSIBLE FOR ALL DESIGN DECISIONS. LaMETTRY'S COLLISION AUDUBON ROAD CHANHASSEN, MN CALCULATIONS SHEET SOUTH SYSTEM CALCULATIONS CULTEC RECHARGER® 150XLHD PROJECT NO: 15-7230.00 DATE: 6/18/15 DESIGNED BY: DPG DRAWN BY: DPG SCALE: SHEET NO: 4 OF 6 N.T.S. CULTEC RECHARGER 150XLHD SPECIFICATIONS 6.0" [150 mm] DIA. INSPECTION PORT CULTEC HVLV FC-24 FEED CONNECTOR PRODUCT SPECIFICATIONS GENERAL USED FOR RETENTION, RECHARGING, DETENTION OR CONTROLLING THE FLOW OF ON-SITE STORMWATER RUNOFF. CHAMBER PARAMETERS 1. THE CHAMBERS WILL BE MANUFACTURED BY CULTEC, INC. OF BROOKFIELD, CT. (203-775-4416 OR 1-800-428-5832) 2. THE CHAMBER WILL BE VACUUM THERMOFORMED OF BLACK HIGH MOLECULAR WEIGHT HIGH DENSITY POLYETHYLENE (HMWHDPE.) GENERAL CULTEC HVLV FC-24 FEED CONNECTORS ARE DESIGNED TO CREATE AN INTERNAL MANIFOLD FOR CULTEC RECHARGER 150XLHD STORMWATER CHAMBERS. LARGE RIB END DETAIL MODEL 150XLRHD STAND ALONE SMALL RIB SMALL RIB END DETAIL LARGE RIB CHAMBER PARAMETERS 1. THE CHAMBERS WILL BE MANUFACTURED BY CULTEC, INC. OF BROOKFIELD, CT. (203-775-4416 OR 1-800-428-5832) 33.0" [838 mm] 3. THE CHAMBER WILL BE ARCHED IN SHAPE. 4. THE CHAMBER WILL BE OPEN-BOTTOMED. 2. THE CHAMBER WILL BE VACUUM THERMOFORMED OF BLACK HIGH MOLECULAR WEIGHT HIGH DENSITY POLYETHYLENE (HMWHDPE). 5. THE CHAMBER WILL BE JOINED USING AN INTERLOCKING OVERLAPPING RIB METHOD. CONNECTIONS MUST BE FULLY SHOULDERED OVERLAPPING RIBS, HAVING NO SEPARATE COUPLINGS OR SEPARATE END WALLS. 3. THE CHAMBER WILL BE ARCHED IN SHAPE. 6. THE NOMINAL CHAMBER DIMENSIONS OF THE CULTEC RECHARGER 150XLHD SHALL BE 18.5 INCHES (470 mm) TALL, 33 INCHES (838 mm) WIDE AND 11 FEET (3.35 m) LONG. THE INSTALLED LENGTH OF A JOINED RECHARGER 150XLHD SHALL BE 10.25 FEET (3.12 m). SMALL RIB 4. THE CHAMBER WILL BE OPEN-BOTTOMED. 7. MAXIMUM INLET OPENING ON THE CHAMBER ENDWALL IS 12 INCHES (300 mm). 5. THE NOMINAL CHAMBER DIMENSIONS OF THE CULTEC HVLV FC-24 FEED CONNECTOR SHALL BE 12 INCHES (305 MM) TALL, 16 INCHES (406 mm) WIDE AND 24.2 INCHES (614 mm) LONG. 8. 6. MANIFOLD. THE NOMINAL INSIDE DIMENSIONS OF EACH SIDE PORTAL WILL BE 8.5 INCHES (216 mm) HIGH BY 12 INCHES (304 mm) WIDE. MAXIMUM ALLOWABLE OUTER DIAMETER (O.D.) PIPE SIZE IN THE SIDE PORTAL IS 10.25 INCHES (260 mm). 132.0" [3353 mm] LARGE RIB MODEL RHD MODEL 150XLRHD STAND ALONE UNITS ARE USED AS SINGLE STAND ALONE SECTIONS. MODEL 150XLSHD STARTER INSTALLED LENGTH = 123.0" [3125 mm] 62.5" [1589 mm] 59.5" [1510 mm] WITHOUT STONE. MODEL SHD 7. THE HVLV FC-24 FEED CONNECTOR CHAMBER SHALL HAVE 2 CORRUGATIONS. 9. (406 mm) WIDE AND 24.2 INCHES (615 mm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mm) HIGH X 20.5 INCHES (521 mm) WIDE. 17. THE RECHARGER 150XLIHD INTERMEDIATE UNIT MUST BE FORMED AS A WHOLE CHAMBER HAVING ONE FULLY OPEN ENDWALL AND ONE PARTIALLY FORMED INTEGRAL ENDWALL WITH A LOWER TRANSFER OPENING OF 10 INCHES (254 mm) HIGH X 20.5 INCHES (521 mm) WIDE. 18. THE RECHARGER 150XLEHD END UNIT MUST BE FORMED AS A WHOLE CHAMBER HAVING ONE FULLY FORMED INTEGRAL ENDWALL AND ONE FULLY OPEN END WALL AND HAVING NO SEPARATE END PLATES OR END WALLS. 19. SEPARATE END PLATES OR SEPARATE END WALLS. THE UNIT WILL FIT INTO THE SIDE PORTALS OF THE RECHARGER 150XLHD AND ACT AS CROSS FEED CONNECTIONS. CULTEC NO. 20L™ POLYETHYLENE LINER GENERAL CULTEC NO. 20L POLYETHYLENE LINER IS DESIGNED AS AN IMPERVIOUS UNDERLAYMENT TO PREVENT SCOURING OF THE STONE BASE CAUSED BY WATER MOVEMENT WITHIN THE CULTEC SYSTEM. CULTEC NO. 20L POLYETHYLENE LINER IS TO BE PLACED BENEATH HVLV FC-24 FEED CONNECTORS WHEN UTILIZING INTERNAL MANIFOLD AND BENEATH ALL INLET PIPES. SIDE PORTAL FOR OPTIONAL INTERNAL MANIFOLD (ACCOMMODATES CULTEC HVLV FC-24 FEED CONNECTOR OR 10.25 INCH (260 mm) MAX. O.D PIPE) MODEL 150XLEHD END SMALL RIB LARGE RIB 18.5" [470 mm] 10.0" [254 mm] MODEL 150XLIHD INTERMEDIATE UNITS ARE USED AS MIDDLE SECTIONS TO EXTEND THE LENGTH OF A LINE. 20.5" [521 mm] LINER PARAMETERS MODEL EHD 1. THE LINER WILL BE PROVIDED BY CULTEC, INC. OF BROOKFIELD, CT. (203-775-4416 OR 1-800-428-5832) 2. THE LINER WILL BE BLACK IN APPEARANCE. 3. THE LINER WILL HAVE A NOMINAL THICKNESS OF 20 mil (0.51 mm). INSTALLED LENGTH ADJUSTMENT = 0.75' [0.23 m] ALL RECHARGER 150XLHD HEAVY-DUTY UNITS ARE MARKED WITH A COLORED STRIPE FORMED INTO THE PART ALONG THE LENGTH OF THE CHAMBER. SIDE PORTAL ACCEPTS CULTEC HVLV FC-24 FEED CONNECTOR. 4. 5. THE LINER WILL HAVE A TENSILE STRENGTH @ BREAK 1" (2.54 cm) OF 75 LBS (334 n) PER ASTM D6693 TESTING METHOD. MODEL 150XLEHD UNITS ARE USED TO END THE LENGTH OF A LINE. 6. THE LINER WILL HAVE AN ELONGATION AT BREAK OF 800% PER ASTM D6693 TESTING METHOD. 20. CHAMBERS MUST HAVE HORIZONTAL STIFFENING FLEX REDUCTION STEPS BETWEEN THE RIBS. 7. THE LINER WILL HAVE A TEAR RESISTANCE OF 11 LBF (49 N) PER ASTM D1004 TESTING METHOD. 21. HEAVY DUTY UNITS ARE DESIGNATED BY A COLORED STRIPE FORMED INTO THE PART ALONG THE LENGTH OF THE CHAMBER. 22. THE CHAMBER WILL HAVE A RAISED INTEGRAL CAP AT THE TOP OF THE ARCH IN THE CENTER OF EACH UNIT TO BE USED AS AN OPTIONAL INSPECTION PORT OR CLEAN-OUT. 23. THE UNITS MAY BE TRIMMED TO CUSTOM LENGTHS BY CUTTING BACK TO ANY CORRUGATION. 9. THE LINER WILL HAVE A PUNCTURE RESISTANCE OF 30 LBF (133 N) PER ASTM D4833 TESTING METHOD. 11. THE LINER WILL HAVE A DIMENSIONAL STABILITY OF <2% PER ASTM D1204 TESTING METHOD. 25. THE CHAMBER WILL BE DESIGNED TO WITHSTAND TRAFFIC LOADS WHEN INSTALLED ACCORDING TO CULTEC'S RECOMMENDED INSTALLATION INSTRUCTIONS. 26. MAXIMUM ALLOWED COVER OVER TOP OF UNIT SHALL BE 12 FEET (3.65 m). CULTEC RECHARGER 150XLHD HEAVY DUTY END DETAIL INFORMATION METHOD. 10. THE LINER WILL HAVE A VOLATILE LOSS OF <1% PER ASTM D1203 TESTING METHOD. 24. THE CHAMBER SHALL BE MANUFACTURED IN AN ISO 9001:2008 CERTIFIED FACILITY. CULTEC RECHARGER 150XLHD HEAVY DUTY THREE VIEW 8. THE LINER WILL HAVE A HYDROSTATIC RESISTANCE OF 100 PSI (689 kpa) PER ASTM D751 TESTING CULTEC HVLV FC-24 FEED CONNECTOR WHERE SPECIFIED 12. RECHARGER 150XLHD HEAVY DUTY CHAMBER 13. 14. THE LINER WILL HAVE A PERM RATING OF 0.041 U.S. PERMS (0.027 METRIC PERMS) PER ASTM E96 PAVEMENT OR FINISHED GRADE METHOD A. 16. THE LINER WILL NOT CONTAIN PLASTICIZERS. 4 OZ. NON-WOVEN FILTER FABRIC AROUND STONE. TOP AND SIDES ARE MANDATORY; BOTTOM PER ENGINEER'S DESIGN PREFERENCE HIDDEN END MIN. 95% COMPACTED FILL 12.0' [3.65m] MAX. BURIAL DEPTH 15. THE LINER WILL CONSIST OF A BLENDED LINEAR POLYETHYLENE. MODEL 150XLEHD 1 - 2 INCH [25- 51 mm] DIA. WASHED, CRUSHED STONE 8.0" [204 mm] MIN.FOR PAVED 10.0" [254 mm] MIN.FOR UNPAVED GENERAL NOTES MODEL 150XLIHD 6.0" [152 mm] MIN. CULTEC HVLV FC-24 FEED CONNECTOR 18.5" [470 mm] CULTEC RECHARGER 150XLHD CHAMBER PIPE PER ENGINEER DESIGN (MAX. O.D. = 10.25 INCHES [260 mm]) (SEE FIGURE 1) MODEL 150XLIHD 6.0" [152 mm] MIN. HIDDEN END PIPE PER ENGINEER DESIGN (MAX. INLET = 12 INCHES [300 mm]) 12.0" [305 mm] MIN. 33.0" [838 mm] CULTEC NO. 20L POLYETHYLENE LINER TO BE PLACED BENEATH HVLV FC-24 FEED CONNECTORS WHEN UTILIZING INTERNAL MANIFOLD AND ALL INLET PIPES 39.0" [991 mm] DESIGN ENGINEER RESPONSIBLE FOR ENSURING THE REQUIRED BEARING CAPACITY OF SUB-GRADE SOILS (TYP.) CULTEC HVLV FC-24 FEED CONNECTOR INLET STRUCTURE GENERAL NOTES RECHARGER 150XLHD BY CULTEC, INC. OF BROOKFIELD, CT. FIGURE 1 MAX. PIPE O.D.= 10.25 INCHES [260 mm] CULTEC RECHARGER 150XLHD CHAMBER INLET STRUCTURE REFER TO CULTEC, INC.'S CURRENT RECOMMENDED INSTALLATION GUIDELINES. MAXIMUM ALLOWED COVER OVER TOP OF UNIT SHALL BE 12 '(3.65m). THE CHAMBER WILL BE DESIGNED TO WITHSTAND TRAFFIC LOADS WHEN INSTALLED ACCORDING TO CULTEC'S RECOMMENDED INSTALLATION INSTRUCTIONS. CULTEC HVLV FC-24 FEED CONNECTOR MODEL 150XLSHD ALL RECHARGER 150XLHD HEAVY DUTY UNITS ARE MARKED WITH A COLORED STRIPE FORMED INTO THE PART ALONG THE LENGTH OF THE CHAMBER. ALL RECHARGER 150XLHD CHAMBERS MUST BE INSTALLED IN ACCORDANCE WITH ALL APPLICABLE LOCAL, STATE AND FEDERAL REGULATIONS. TRIM PORTAL TO UTILIZE INTERNAL MANIFOLD FEATURE CULTEC HVLV FC-24 FEED CONNECTOR ZOOM OF SIDE PORTAL SHOWING MAX. PIPE O.D. CULTEC TYPICAL INLET CONNECTION CULTEC RECHARGER 150XLHD HEAVY DUTY TYPICAL CROSS SECTION CULTEC RECHARGER 150XLHD HEAVY DUTY TYPICAL INTERLOCK 1-2" [25-51 mm] WASHED, CRUSHED STONE SURROUNDING CHAMBERS AND 8.0" [203 mm] MIN. INTO CHAMBER PAVEMENT OR FINISHED GRADE RECHARGER 150XL HEAVY DUTY CHAMBER 4 OZ. NON-WOVEN FILTER FABRIC AROUND STONE. TOP AND SIDES ARE MANDATORY; BOTTOM PER ENGINEER'S DESIGN PREFERENCE 24.2" [614 mm] PAVEMENT SUB-BASE (WHEN APPLICABLE) OPTIONAL INSPECTION PORT (SEE DETAIL ) 27.2" [691 mm] MIN. SQUARE MINIMUM 95% COMPACTED FILL 4 OZ. NON-WOVEN FILTER FABRIC AROUND STONE. TOP AND SIDES ARE MANDATORY; BOTTOM PER ENGINEER'S DESIGN PREFERENCE MODEL FC 24 10.25" [260 mm] PAVEMENT OR FINISHED GRADE 6.0" [152 mm] MIN. 12.0" [300 mm] MAX. INLET 12.0" [305 mm] MIN. 6.0 INCH [152 mm] MIN. DEPTH OF 1-2 INCH [25-51 mm] WASHED CRUSHED STONE BENEATH AND ABOVE CHAMBERS 16.0" [406 mm] CULTEC FC NEENAH FOUNDRY MODEL R-5900-A (OR EQUAL) HEAVY DUTY FRAME AND LID CULTEC, Inc. Subsurface Stormwater Management Systems CULTEC P.O. Box 280 878 Federal Road Brookfield, CT 06804 www.cultec.com 6.0" [152 mm] MIN. MAINTAIN 6.0" [152 mm] CLEARANCE BETWEEN HEAVY DUTY LID AND PVC CLEAN-OUT CAP SIDE PORTAL TO BE CUT IN FIELD TO ALLOW FOR HVLV FC-24 FEED CONNECTOR AS NEEDED. CUT SHALL BE WITHIN 1/4" [6 mm] TOLERANCE OF SIDE PORTAL TRIM GUIDELINE 6.0" [150 mm] SDR-35 / SCH. 40 PVC ENDCAP CLEAN-OUT ADAPTER W/ SCREW-IN CAP PH: (203) 775-4416 PH: (800) 4-CULTEC FX: (203) 775-1462 [email protected] 12.0" [305 mm] MIN. CULTEC NO. 20L POLYETHYLENE LINER TO BE PLACED BENEATH HVLV FC-24 FEED CONNECTORS WHEN UTILIZING INTERNAL MANIFOLD AND BENEATH ALL INLET PIPES 6.0" [150 mm] SDR-35 / SCH. 40 PVC COUPLING TRIM CHAMBER INSPECTION PORT KNOCK-OUT TO MATCH O.D. OF 6.0" [150 mm] INSPECTION PORT PIPE 12.0 INCH [305 mm] MIN. WIDTH OF 1-2 INCH [25-51 mm] WASHED CRUSHED STONE BORDER SURROUNDING ALL CHAMBERS TM 12.0" [300 mm] SDR-35 / SCH. 40 PVC COLLAR 6.0" [150 mm] SDR-35 / SCH. 40 PVC RISER 6.0' [1.8 m] MIN. CULTEC NO. 20L POLYETHYLENE LINER BENEATH FEED CONNECTORS CULTEC RECHARGER 150XLHD HEAVY DUTY PLAN VIEW 18.5" [471 mm] FIELD PLACED CLASS "C" CONCRETE CULTEC RECHARGER 150XLHD HEAVY-DUTY CHAMBER PIPE DESIGN AND ELEVATION TBD BY ENGINEER. PIPE TO BE INSERTED 8.0 INCHES [203 mm] MIN. INTO CHAMBER. MAX. 12.0 INCHES [300 mm] PIPE ALLOWED IN ENDWALL 8.0" [202 mm] MIN. FOR PAVED 10.0" [254 mm] MIN. FOR UNPAVED PAVEMENT OR FINISHED GRADE 16.4" [418 mm] CULTEC HVLV FC-24 FEED CONNECTOR WHERE SPECIFIED 10.0' [3.0 m] MIN. CULTEC NO. 20L POLYETHYLENE LINER BENEATH INLET PIPES MIN. 95% COMPACTED FILL 12.0' [3.65m] MAX. BURIAL DEPTH 6.0" [150 mm] SDR-35 / SCH 40 PVC (INSERTED 8.0" [203 mm] INTO CHAMBER) 12.0" [305 mm] CULTEC HVLV FC-24 FEED CONNECTOR THREE VIEW OPTIONAL INSPECTION PORT - ZOOM DETAIL THIS DRAWING WAS PREPARED TO SUPPORT THE DESIGN ENGINEER FOR THE PROPOSED SYSTEM. IT IS THE ULTIMATE RESPONSIBILITY OF THE DESIGN ENGINEER TO ASSURE THAT THE STORMWATER SYSTEM'S DESIGN IS IN FULL COMPLIANCE WITH ALL APPLICABLE LAWS AND REGULATIONS. IT IS THE DESIGN ENGINEER'S RESPONSIBILITY TO ENSURE THAT THE CULTEC PRODUCTS ARE DESIGNED IN ACCORDANCE WITH CULTEC'S MINIMUM REQUIREMENTS. CULTEC INC. DOES NOT APPROVE PLANS, SIZING, OR SYSTEM DESIGNS. THE DESIGNING ENGINEER IS RESPONSIBLE FOR ALL DESIGN DECISIONS. CULTEC INTERNAL MANIFOLD - OPTIONAL INSPECTION PORT DETAIL RECHARGER 150XLHD DETAIL SHEET TRAFFIC APPLICATION CULTEC RECHARGER® 150XLHD PROJECT NO: DATE: 04/2014 DESIGNED BY: CULTEC, INC DRAWN BY: TECH SCALE: SHEET NO: 1 OF 2 N.T.S.