Multi EL Desk (Electric Version)
Transcription
Multi EL Desk (Electric Version)
biomorph ® multi EL desk electric versio n USER SIDE Ground Support Equipment (US) ltd., DBA biomorph, 11 Broadway, New York, NY 10004. 888 302 3375 fax: 212 809 4324 [email protected] biomorph interactive desk electric ® multi ASSEMBLY INSTRUCTIONS Questions? Call 888 302 DESK For info visit www.biomorph.com frame assembly Please use the instructions enclosed with the frame & page2 top assembly TOOL Screw gun w/philips bit 6 remove desktops from crate 1 Place desktops upside down on clean floor. assemble keyboard mech 2 Packed in smallest carton with hardware.Use enclosed instructions to assemble only. 3/4" screw x 6 3 Use to attach keyboard mech to keyboard surface. Use pilot holes on bottom of surface. ! kb IMPORTANT DO NOT OVERDRIVE SCREWS turn main desktop over 4 Place desktop ontop of frame assy. and use location holes on surface to position frame 3/4" silver screws x 16 Use to attach desktop to support plates from underneath. Drive directly into surface. Fill all holes. 5 ! ! The completed desk is very heavy and must not be moved by lifting the surface alone, otherwise damage may occur. attach controller box, adjustment control switch wire guide clips 8 Found with frame. Screw into surface with supplied screws using pilot holes. Connect wires as per frame assy sheet. privacy/modesty panel attachment pilot holes Use to route wires under surface.Screw directly into surface with supplied screws. use location holes on underside of top to position on frame controller box 7 DO NOT OVERDRIVE SCREWS 1 1/2" black hex-head nut-bolt sets x 8 found in crate w/tops 6 optional CPU holder 7 THROUGH-HOLES FOR BLACK HEX-HEAD NUT-BOLT SETS Place grommets in 3 holes. use for wire management. remove to mount add-ons. PILOT HOLES FOR 3/4” SCREWS UNDERSIDE OF DESKTOPS GROUND SUPPORT EQUIPMENT (U.S.) Ltd. 11 Broadway, space 905, New York, NY 10004, U.S.A. Tel: 888 302 DESK. (212) 809-4323 Fax:(212) 809-4324. Email: [email protected] You are hereby made aware that the content of any material submitted to you [upon your request] by Biomorph/Ground Support Equ. (US) Ltd. in connection with its furniture designs is considered proprietary to Biomorph/Ground Support Equ. (US) Ltd. and protected under federal copyright, trademark and patent laws, and under federaland state unfair competition law. Unauthorized copying, dissemination and/or use, both unintentional and intentional may subject you to payment of damages through legal action. © 2003 Biomorph/Ground Support Equ. (US) Ltd. grommet holes frame Use to attach keyboard mechanism/small surface assembly to main surface. Insert into thru-holes from top of large surface. Screw tight. plastic grommets x 3 9 keyboard surface adjustment lever. squeeze to release, let go to lock. adjustment control switch keyboard surface tilt knob 3 keyboard surface adjustment mechanism Operation of the DPF1C “one reference” DPF1C - Desk Panel V V = Parallel up = Parallel down S = Store memory • •• ••• = Memory 1 = Memory 2 = Memory 3 V Up and down ( V): Just activate either the up or down button for parallel drive and the system will drive until the button is released again or the system reaches end position. Memory: The four small buttons are used for memory drive/storing memory. Store memory • Press S – button, the display will flash for 2 seconds • Within these two seconds press one of the small buttons with dots and the position will be stored at this button. • The panel will acknowledge by showing “1”, “2” or “3” in the display depending on chosen position Memory drive (small buttons with dots) Press one of the memory buttons and the system will start driving to the pre-programmed memory position. Keep the button pressed until the position is reached. Display function Shows the actual height in either cm or inch. Page 16 of 36