VFSO61

Rola Roof Racks
5 Year Warranty
Vehicle Compatibility Guide
This Fit Kit is compatible with the following vehicles.
VFSO61
Revision A
Rack System: (“Rola Roof Rack”). The Rola Roof Rack incorporates three components:
Make
Model
End Supports
Holden
Rodeo 2D Space Cab RA
02/03-06/08
Fit Kit
Holden
Rodeo 2D ute
RA
02/03-06/08
Cross Bars
Holden
Rodeo 4D ute
RA
02/03-06/08
Holden
Colorado 2D Space Cab RC
Holden
Colorado 2D ute
RC
07/08-06/12
Holden
Colorado 4D ute
RC
07/08-06/12
Cequent warrants that, subject to the exclusions and limitations below, the Rola Roof Rack will be free from
defects in materials and workmanship for a period of 5 years commencing on the date of sale by the
authorised Rola stockist to the original purchaser of the entire Rola Roof Rack, including the End Support, Fit
Kit and Cross Bars.
Year
07/08-06/12
If a defect appears in the Rola Roof Rack before the end of the warranty period and Cequent finds the Rola
Roof Rack to be defective in materials or workmanship, Cequent will, in its sole discretion, either:
1.
Repair the Rola Roof Rack or the defective component of the Rola Roof Rack free of charge;
2.
Replace the Rola Roof Rack or the defective component of the Rola Roof Rack; or
3.
Refund the purchase price of the Rola Roof Rack to the original purchaser.
Cequent reserves the right to change the design, specifications or composition of the Rola Roof Rack without
notice and without liability.
VEHICLE COMPATIBILITY & WARRANTY
Cequent reserves the right to replace defective products or components with products or components of
similar quality, grade and composition, where an identical product or component is not available.
Goods presented for repair may be replaced by refurbished goods of the same type rather than being repaired.
Refurbished parts may be used to repair the goods.
The 5 year warranty only applies where the entire Rola Roof Rack is purchased in one transaction and is
installed and used together.
The 5 year warranty does not apply where:
1.
The Rola Roof Rack is not installed in compliance with the fitting instructions provided;
2.
The Rola Roof Rack is not used as intended or designed;
3.
Any part of the Rola Roof Rack, such as the End Supports, Fit Kits, or Cross Bars, is used with
other products or components notintended to be used in conjunction with the modular Rola Roof
Rack system;
4.
The Rola Roof Rack has been on-sold or assigned by the original purchaser;
5.
The Rola Roof Rack has been modified or repaired by someone other than Cequent or an authorised
Rola stockist;
6.
Cequent cannot establish any fault in the Rola Roof Rack after testing;
7.
The Rola Roof Rack has been subject to abnormal conditions, including fire, water, humidity,
pressure, stress or similar;
8.
The defect in the Rola Roof Rack has arisen due to abuse, misuse, neglect or accident;
9.
The defect in the Rola Roof Rack has arisen due to the unlawful or unusual operation of the vehicle
to which it is fitted;
10.
The defect in the Rola Roof Rack has arisen due to the purchaser’s failure to properly assemble,
install, fit, maintain or use the Rola Roof Rack in accordance with the specifications and instructions
provided by Cequent.
IF YOUR VEHICLE IS NOT LISTED HERE
We are constantly adding vehicles to these kits, If the set-up instructions for your vehicle do not
appear in this guide, go to
up information
www.rola.com.au/fitkits/vcs061.pdf
for your set
For safety and use instructions, please refer to any General or Specific Fitting Instructions and Use & Care
Instructions enclosed with the Rola Roof Rack or on our website at www.rola.com.au.
This warranty does not extend to fair wear and tear. Warranty claims can be made by contacting Cequent
directly using the details below. A warranty claim must be accompanied by proof of purchase (such as receipt)
and details of the alleged defect.
It is the purchaser’s responsibility to arrange and pay for any warranty claims, including the shipment of goods
to Cequent for inspection. The purchaser may seek reimbursement from Cequent for the costs of such
activities, providing Cequent notifies the purchaser in writing that a warranty claim is justified. Any such
claims must be made in writing via post or email.
The benefits of this warranty are in addition to any rights and remedies imposed by Australian State and
Federal legislation that cannot be excluded. Nothing in this warranty is to be interpreted as excluding,
restricting or modifying any State or Federal legislation applicable to the supply of goods and services which
cannot be so excluded, restricted or modified.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount to a major failure. Cequent makes no express
warranties or representations other than set out in this warranty.
The repair or replacement of Rola Roof Racks or part there of, or a refund of the purchase price of
the Rola Roof Rack, is the absolute limit of Cequent’s liability under this express warranty.
Cequent, a division of TriMas Corporation Pty Ltd. 49 Pacific Drive, Keysborough, VIC, 3173.
Phone 1800 812 017.
www.rola.com.au.
For detailed warranty information visit us online.
ABN 60 004 546 543
Please complete the Warranty form on the reverse side and post to:
PO BOX 4050
Dandenong South
VIC 3164
Australia
For more information visit www.rola.com.au
Installation Guide
follow the vehicle specific instructions to set up your racks correctly
Make
Model
Door/Body
Series
Released
Finished
Strap
No. / Location
Strap Bolt
Position
7008
Holden
Rodeo
2D Space Cab
RA
02/2003
Holden
Rodeo
2D ute
RA
02/2003
Front
7008
Holden
Rodeo
4D ute
RA
02/2003
7008
Colorado
2D Space Cab
RC
07/2008
Holden
Colorado
2D ute
RC
07/2008
Strap Bolt Position
na
Front
Rola Roof Rack Warranty Registration Card
Front 845mm
Rear na
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Pad Adaptor Requirement
(shown from the underside)
To ensure smooth handling of any warranty claims, please complete the form below and send to the address indicated overleaf.
The strap bolt
The strap bolt position is important
to the correct set-up of your end
supports.
Refer to the vehicle specific image
and follow the instructions for
correct installation position.
Place Strap bolt
facing down
Place Strap bolt
facing up
Customer Details
27-0845
Front LH
27-0847
Rear LH
27-0844
Front RH
27-0846
Rear RH
Name
Address
Suburb
Store Details
End Support Distance and Bar length
Equal =
Equal =
(x) mm
Concealed
Equal =
Equal =
(x) mm
Extended
Your roof rack is at its strongest and
looks its best when the cross bar is
centred equally within the end
supports.
Measure the distance between end
supports on the underside of the
bar. Slide the end supports until the
distance between them is correct
and the cross bar is centred.
Lock the bars in place using the
locking lever and proceed to the
next step.
Dealer/Reseller
Suburb
End suport distance from mid-pillar
A
B
00mm 00mm
Vehicle/Product Details
Vehicle Make
Model/Year
Front
Front 300mm
Rear na
Front 300mm
Rear na
If specified to do so, fit the supplied Pad
adaptors to the feet of each End Support in
the location indicated.
The numbers shown to the left correspond to
the correct location of the feet pads. The
numbers are moluded in the underside of
each part.
The numbers shown above in the vehicle
table correspond to the correct adaptor
block to be inserted in the foot pad (if
required)
Refer to step 1 of the fitting instructions for
more information.
Distances for setting out your racks are
defined from the mid pillar of the
vehicle. Both forward and rearward
measurements are given to the centre of
the straps.
Take care to set your racks out
as shown to ensure your racks fit and
perform as they have been design to.
Right & Left hand sides of the vehicle are
defined as you would be when sitting in
the vehicle
RH
Product/Part Numbers
Mid pillar
Please tick if you do not wish to receive product information or marketing offers
from Rola.
N/A
N/A
Front 300mm
Rear 400mm
Front 845mm
Rear na
06/2012
Place strap bolt
facing up
N/A
na
Front
7008
N/A
N/A
Front 300mm
Rear 400mm
Front 300mm
Rear na
Front 845mm
Rear 845mm
06/2012
Place strap bolt
facing up
N/A
N/A
N/A
Front
End Support Distance
from Mid Pillar
N/A
Front 845mm
Rear na
7008
06/2008
Place strap bolt
facing up
Holden
na
06/2008
Place strap bolt
facing up
N/A
Front 845mm
Rear na
Front
7008
Pad Apaptors
na
06/2008
Place strap bolt
facing up
End Support Distance
and Bar length (x)
Front
LH
ROLA Ambassador
Josh Sanders - Australian Pro Wakeboarder
ROLA Ambassador
Niki Gudex - Australias Number One
Female Mountain Biker
ROLA Ambassador
Ryan Hipwood - Australian Pro Surfer
Installation Guide
follow the vehicle specific instructions to set up your racks correctly
Make
Model
Door/Body
Series
Released
Finished
Strap Bolt
Position
Strap
No. / Location
7008
Holden
Colorado
4D ute
RC
07/2008
06/2012
Place strap bolt
facing up
Front
End Support Distance
and Bar length (x)
7008
Pad Apaptors
N/A
Front 845mm
Rear 845mm
N/A
End Support Distance
from Mid Pillar
N/A
N/A
Strap Set Up Requirement:
Positions the strap, according to the “End support
distance from mid pillar” information. Peel back
the lower door seal. Locate the strap hook over
the sheet metal to secure the strap, reposition the
door seal over strap.
Strap hook
Front 300mm
Rear 400mm