Bronze Gate Valves

Transcription

Bronze Gate Valves
Hattersley-Section 2a
25/4/06
9:06 am
Page 1
SECTION
2a
Bronze
Gate Valves
Tel: +44 (0)1695 712800 Fax: +44 (0)1695 712820
Email: [email protected]
[email protected]
www.hattersley.com
04.06
Hattersley-Section 2a
25/4/06
9:06 am
Page 2
Contents
Bronze Gate Valves
Contents
Figure Number Index
Bronze Gate Valves Introduction
The Pressure Equipment Directive
Bronze Gate Valves Data Sheets
Page
2
3
4
5 - 12
Fig No
Page
33X
33XLS
30
30LS
30C
30CLS
33
669
28
35PN16
609
5
5
6
6
7
7
8
9
10
11
12
In this catalogue we have endeavoured to make the information as accurate as
possible, and we cannot accept any responsibility should it be found that in any
respect the information is inaccurate or incomplete or becomes so as a result
of further developments.
2
04.06
Hattersley-Section 2a
25/4/06
9:06 am
Page 3
Introduction
Bronze Gate Valves
All Hattersley bronze gate valves are
inside screw pattern with either rising
stem or non-rising stem configuration.
Valve bodies, with the exception of
the DZR range, are made from
bronze castings and have integral
seating surfaces.
The majority of the range have a
threaded bonnet but union bonnet
valves are available.
Valves are fitted with asbestos-free
gland packing as standard.
The BSI Kitemark against a figure
number in the table below indicates
that all or part of that range is
Kitemarked to the relevant British
Standard.
The WRAS Approved Product Mark
against a figure number indicates that
all or part of that range has been
independently assessed and certified
under the Water Regulations Advisory
Scheme and is listed in the Water
Fittings and Materials Directory.
Fig No
35PN16$
30C*$
30CLS*$
30*$
30LS*$
33X*$
33XLS*$
33*
669
28
609
04.06
PN
Rating
16
16
16
20
20
20
20
32
32
32
$ WRAS Approved Product
* Kitemarked to the relevant British Standard
Series
B
B
B
B
B
B
B
B
B
A
End
Connections
Flanged
Compression
Compression
Threaded
Threaded
Threaded
Threaded
Threaded
Threaded
Threaded
Threaded
Size
Range
15 - 100mm
15 - 54mm
15 - 54mm
1/4 - 3in
1/4 - 3in
1/4 - 4in
1/4 - 4in
1/4 - 3in
1/4 - 2in
1/2 - 3in
1/4 - 3in
Bonnet
Pattern
Threaded
Threaded
Threaded
Threaded
Threaded
Threaded
Threaded
Threaded
Union
Threaded
Threaded
Wedge
Material
Bronze
Bronze
Bronze
DZR Alloy
DZR Alloy
Bronze
Bronze
Bronze
Bronze
Bronze
Bronze
3
Hattersley-Section 2a
25/4/06
9:06 am
Page 4
The Pressure Equipment Directive
Bronze Gate Valves
Fig. No.
30C/30CLS
30/30LS
PN(PS)
16
20
33X/33XLS
20
33
32
669
28
32
8.6
35
609
16
32
DN
15-54
1/2"-2"
1/4"-2"
21/2"-4"
1/4"-11/4"
11/2"-3"
1/4"-11/4"
11/2"-2"
1/2"-3"
15-50
65-100
1/4"-3"
Fluid Group (1) Category
2L
SEP
2G
SEP
2G
SEP
2G
1 (2)
2G
SEP
2G
1 (2)
2G
SEP
2G
1 (2)
2L
SEP
2G
SEP
2G
1 (2)
2G
SEP
FLUID GROUPS
2G = Group 2 gases (Also Group 2 liquids but NOT group 1 gases nor
Group 1 liquids)
2L = Group 2 liquids only
CATEGORY
SEP = Sound Engineering Practice
I = Category I (CE Marked)
4
04.06
Hattersley-Section 2a
25/4/06
9:06 am
Page 5
Fig. 33X - 33XLS
Bronze Gate Valves
PN20 - Series B
Pressure/Temperature Rating
BSEN12288 PN20 Series B
9 bar at 180ºC
20 bar from -10 to 100ºC
Test Pressures (Hydraulic)
Shell: 30 bar
Seat: 22 bar
Specification
Kitemarked to BS EN 12288
WRAS Approved Product
Non-rising stem
Threaded bonnet
One piece wedge
BS21 Taper thread (ISO 7)
Available with NPT thread (33XAT)
1/2” to 4”
Available with lockshield (33XLS)
up to 2”
See page 4 of this section for
PED category.
Material Specification
Component
Body
Bonnet
Stem (1/4 to 2in)
(21/2 & 3in)
(4in)
Disc
Packing
Packing Gland (1/4 to 3in)
(4in)
Gasket (3 & 4in)
Dimensions
Nominal Size
A
B
C
D
Weight
Material
Bronze
Bronze
DZR Brass
Brass
Manganese Bronze
Bronze
Asbestos Free
Brass
Bronze
Asbestos Free
Specification
BS EN
1982 CC491K
1982 CC491K
12164 CW602N
12164 CW614N
1982 CC491K
C
12164 CW614N
1982 CC491K
B
in
mm
mm
mm
mm
kg
1/4
3/8
1/2
3/4
46
75
57
87
0.27
46 51
75 82
57 57
87 86
0.26 0.35
55
95
69
112
0.55
1 11/4 11/2
63
71
73
118 144 166
69
76
81
124 149 175
0.84 1.18 1.66
2
83
190
94
196
2.55
21/2
96
219
140
4.30
3
4
105 162
259 366
150 232
6.4 18.37
A
33X
D
33XLS
04.06
5
Hattersley-Section 2a
25/4/06
9:06 am
Page 6
Fig. 30 - 30LS
DZR Gate Valves
PN20 - Series B
Pressure/Temperature Rating
BSEN12288 PN20 Series B
9 bar at 180ºC
20 bar from -10 to 100ºC
Test Pressures (Hydraulic)
Shell: 30 bar
Seat: 22 bar
Specification
Kitemarked to BS EN 12288
WRAS Approved Product
Non-rising stem
Threaded bonnet
One piece wedge
BS21 Taper thread (ISO 7)
Available with lockshield (30LS)
Available with NPT thread (30AT)
See page 4 of this section for
PED category.
Material Specification
Component
Stem
Gland Packing
Stem Ring
Bonnet
Body
Disc
Dimensions
Nominal Size
A
B
C
D
Lockshield Key
C
B
Weight
A
Material
DZR Copper Alloy
Asbestos Free
DZR Copper Alloy
DZR Copper Alloy
DZR Copper Alloy
DZR Copper Alloy
in
mm
mm
mm
mm
Fig
Ref
kg
1/2
51.6
90
56.8
80
391
A
0.32
3/4
56
100
56.8
85
391
A
0.45
Specification
BS EN
12164 CW602N
ASTM
-
12164
12165
12165
12165
-
1
64
120
69.2
105
391
2
0.7
CW602N
CW602N
CW602N
CW602N
11/4
72
125
69.2
110
391
2
1.22
11/2
75
145
75.5
130
391
2A
1.55
2
91
170
81.5
155
391
3
2.45
30
E
30LS
6
04.06
Hattersley-Section 2a
25/4/06
9:06 am
Page 7
Fig. 30C - 30CLS
DZR Gate Valves
PN16
18
Pressure/Temperature Rating
(for liquid service)
5 bar at 120ºC
6 bar at 110ºC
10 bar at 65ºC
16 bar from 2 to 30ºC
16
Pressure bar
14
12
10
Test Pressures (Hydraulic)
Shell: 24 bar
Seat: 17.6 bar
8
6
4
2
0
0
20 40 60 80 100 120 140
Temperature ˚C
Material Specification
Specification
Material
BS EN
Bronze
Bronze
Bronze
Bronze
PTFE or PTFE/Neoprene
Brass
Brass
Cast Iron
Steel
Brass
Brass
Component
Body
Disc
Stem
Bonnet
Packing
Gland
Packing Nut
Handwheel
Handwheel Nut
Compression Olive
Compression Nut
Dimensions
Nominal Size
A
B
C
D
E
F
Lockshield Key
Weight
ASTM
B62-C83600
B62-C83600
B62-C83600 or B21-C48200
B62-C83600 or B124-C37700
Specification
Kitemarked to BS EN 12288
WRAS Approved Product
Non-rising stem
Threaded bonnet
One-piece wedge
Compression ends to BS EN 1254-2
Suitable for copper pipe to
BS EN 1087:Table X
Available with lockshield (30CLS)
See page 4 of this section for
PED category.
A
B16-C36000
B16-C36000 / B124-C37700
B
B135-C26000
B584-C85700
mm
mm
mm
mm
mm
mm
mm
Fig No
Ref
15
54
77
46
12.7
80
65
391
A
22
61
88
53
19.1
85
70
391
A
28
67
106
58
25.4
105
76
391
2
35
83
122
72
31.8
110
92
391
2
42
83
136
80
38.1
130
101
391
2A
54
100
170
97
50.8
155
125
391
3
kg
0.34
0.49
0.75
1.06
1.36
2.37
F
30C
E
D
C
F
30CLS
04.06
7
Hattersley-Section 2a
25/4/06
9:06 am
Page 8
Fig. 33
Bronze Gate Valves
PN32 - Series B
36
Pressure/Temperature Rating
BS5154 PN32 Series B
14 bar at 198ºC
32 bar from -10 to 100ºC
32
28
Pressure bar
Test Pressures (Hydraulic)
Shell: 48 bar
Seat: 35.2 bar
Specification
Kitemarked to BS EN 12288
Non-rising stem
Threaded bonnet
One piece wedge
BS21 Taper thread (ISO 7)
Available with NPT thread (33AT)
1/2” to 3”
See page 4 of this section for
PED category.
24
20
16
Ste
am
12
ur
ate
d
8
4
t
Sa
0
0
40 80 120 160 200 240
Temperature ˚C
Material Specification
Component
Stem
Gland Packing
Stem Ring
Bonnet (1/4 to 2in)
(21/2 & 3in)
Body
Wedge
Material
Bronze
Asbestos Free
Brass
Brass
Bronze
Bronze
Bronze
Specification
BS EN
1982 CC491K
ASTM
B62
12164 CW614N
12165 CW617N
1982 CC491K
1982 CC491K
1982 CC491K
B455-385
B124 Alloy 2
B62
B62
B62
Dimensions
Nominal Size
A
in
mm
1/4
3/8
1/2
3/4
46
46
51
55
1
63
11/4
71
11/2
73
2
83
21/2
108
3
117
B
C
Weight
mm
mm
kg
78
60
0.36
78
60
0.35
86
70
0.47
98
80
0.6
120
85
0.92
148
95
1.41
172
102
1.92
196
120
2.72
241
140
5.62
256
150
7.89
C
B
A
8
04.06
Hattersley-Section 2a
25/4/06
9:06 am
Page 9
Fig. 669
Bronze Gate Valves
PN32 Series A
Pressure/Temperature Rating
BSEN12288 PN32 Series A
14 bar at 260ºC
32 bar from -10 to 120ºC
Test Pressures (Hydraulic)
Shell: 48 bar
Seat: 35.2 bar
Specification
BS EN 12288
Rising stem
Union bonnet
One piece wedge
Taper thread (ISO7-1)
Available with NPT thread (669AT)
See page 4 of this section for
PED category.
Material Specification
Component
Body
Bonnet
Stem
Disc
Packing
Gland
Packing Nut
Handwheel
Handwheel Nut
Dimensions
Nominal Size
A
B
C
Weight
Specification
BS EN
1982 CC491K
1982 CC491K
1982 CC491K
1982 CC491K
Material
Bronze
Bronze
Bronze
Bronze
Asbestos Free
Brass
Brass
Aluminium
Brass
12164 CW614N
12164 CW614N
12164 CW614N
C
in
mm
mm
mm
kg
1/4
3/8
1/2
3/4
46
134
69
0.32
46
134
69
0.31
51
137
76
0.46
55
169
81
0.72
1
63
194
94
1.10
11/4
71
232
100
1.50
11/2
73
266
120
2.25
2
83
321
140
3.20
B
A
04.06
9
Hattersley-Section 2a
25/4/06
9:06 am
Page 10
Fig. 28
Bronze Gate Valves - Lever Operated
8.6 bar CWP
Pressure/Temperature Rating
4 bar at 150ºC
8.6 bar cold (non-shock)
Test Pressures (Hydraulic)
Shell: 12.5 bar
Seat: 12.5 bar
Specification
Threaded cover
BS21 Taper thread (ISO7-1)
Lever operated
See page 4 of this section for
PED category.
Material Specification
Component
Stem
Gland Packing
Stuffing Box
Gate
Disk Arm
Body
B
Material
Stainless Steel
Asbestos Free
Brass
Bronze
Bronze
Bronze
Specification
BS EN
10088-3 X8CrNiS18-9
ASTM
AISI 420
12164 CW614N
1982 CC491K
1982 CC491K
1982 CC491K
B455-385
B62
B62
B62
Dimensions
Nominal Size
A
B
in
mm
mm
1/2
3/4
46
40
51
45
1
55
55
11/4
64
65
11/2
65
70
2
81
95
21/2
95
120
3
122
145
C
Weight
mm
kg
76
0.4
89
0.6
102
1.0
114
1.4
127
1.7
140
2.8
152
4.8
178
8.0
A
C
10
04.06
Hattersley-Section 2a
25/4/06
9:06 am
Page 11
Fig. 35PN16
Bronze Gate Valves
PN16 Series B
18
Pressure/Temperature Rating
BS5154 PN16 Series B
7 bar at 170ºC
16 bar from -10 to 100ºC
16
Pressure bar
14
12
Test Pressures (Hydraulic)
Shell: 24 bar
Seat: 17.6 bar
10
8
Specification
WRAS Approved product
Non-rising stem
Threaded bonnet
One piece wedge
Flanged to BS4504 PN16
Table E and F
Available with lockshield (35LS)
Available with position indicator and
locking device (35PN16LDI) in all sizes
except for 32, 65 and 100mm.
See page 4 of this section for
PED category.
dS
tea
m
6
ra
te
4
Sa
tu
2
0
0
40 80 120 160 200
Temperature ˚C
Material Specification
Component
Stem (15 to 50mm)
Stem (65 to 100mm)
Gland Packing
Stem Ring (15 to 80mm)
(100mm)
Bonnet (15 to 50mm)
(65 to 100mm)
Body
Wedge
Specification
BS EN
12164 CW602N
1982 CC491K
Material
DZR Copper Alloy
Bronze
Asbestos Free
Brass
Bronze
Bronze
Bronze
Bronze
Bronze
12164 CW614N
1982 CC491K
1982 CC491K
1982 CC491K
1982 CC491K
1982 CC491K
C
Dimensions
Nominal Size
A
B
C
D
Weight
mm
mm
mm
mm
mm
kg
15
80
100
70
95
1.4
20
90
110
80
105
2.1
25
100
130
85
115
2.7
32
110
145
95
140
4.0
40
120
165
120
150
4.4
50
135
200
120
165
6.3
65
165
240
155
185
9.1
80
185
280
180
200
15.4
100
190
365
230
220
22.2
B
D
A
04.06
11
Hattersley-Section 2a
25/4/06
9:06 am
Page 12
Fig. 609
Bronze Gate Valve
PN32 - Series B
36
Pressure/Temperature Rating
14 bar at 198ºC
32 bar from -10 to 100ºC
32
28
Pressure bar
Test Pressure
Each valve is individually hydrostatically
tested to BS EN 12266
at the following test pressures.
Shell: 30 bar
Seat: 22 bar
24
20
16
Ste
am
12
ur
ate
d
8
Specification
Rising stem
Threaded bonnet
One piece wedge
Bronze trim
Taper thread BS EN 10226
(BS 21-ISO 7)
Complies with BS EN 12288
4
0
t
Sa
0
40 80 120 160 200 240
Temperature ˚C
Material Specification
Component
Body
Bonnet
Stem (1/4 to 2”)
(21/2”)
(3”)
Disc
Packing Ring
Gland
Packing Nut (21/2 & 3”)
Packing Nut (1/4 to 2”)
Handwheel
Identification Plate
Handwheel Nut
C
B
Dimensions
Nominal Size
A
B Open
C
Weight
in
mm
mm
mm
kg
Specification
BS EN
1982 CC491K
1982 CC491K
1982 CC491K
12163 CW301G
1982 CC491K
1982 CC491K
WRAS Listed & Approved
12164 CW614N
12164 CW721R
12164 CW614N
Material
Bronze
Bronze
Bronze
AL. Brass (CA12)
Bronze
Bronze
Asbestos Free
Brass
Brass
Brass
Aluminium
Aluminium
Brass
12164 CW614N
1/4
3/8
1/2
3/4
46
129
60
0.35
46
129
70
0.40
51
133
70
0.50
55
162
80
0.75
1
63
191
85
1.30
11/4
71
223
95
1.70
11/2
73
253
105
2.60
2
83
307
120
3.50
21/2
108
374
140
6.00
3
117
436
180
8.80
A
12
04.06