K4VN Cuts - Keen Pump
Transcription
K4VN Cuts - Keen Pump
Solids-Handling Pumps K4VN(X) 4” Submersible, Enclosed Impeller (Class 1, Div. 1, Groups C & D Hazardous Location) 2-VANE ENCLOSED IMPELLER • • • • Efficient Operation, Non-clogging Pump-Out Vanes Prevent Material Build-up Pressure Balance on Shaft Seal for Long Life Positive Pumping Action through Impeller STRONG PERFORMANCE • • • • Ideal for Higher Flows, Lower Heads Operate to Shut-off Head without Damage Non-Overloading Performance Curve 3-Bearing Shaft Support LONG SERVICE LIFE • Dual Silicon Carbide Shaft Seals • Low Motor Operation Temperatures • Continuously Lubricated Ball Bearings LOW MAINTENANCE • Easily Replaceable Impeller Wear Ring Restores Original Pump Performance • Unobstructed Impeller Passageway • Grit-Resistant Silicon Carbide Shaft Seals • Large, 3” diameter Solids-Handling • High Service Factor Motor Handles Tough Electrical Operating Conditions CAPABILITIES: • Flows-------------------------------------- to 700 GPM • Heads------------------------------------- to 67 Feet • HP Range-------------------------------- 1 - 10 HP • Voltage / Phase Options------------- 208/230 V, 1 Phase - 208/230/460 V, 3 Phase • Discharge Connections-------------- 4” ANSI Class 125 Horizontal Flange • Motor Speeds--------------------------- 1150 / 1750 RPM • Solids-Handling------------------------ 3” • Impeller---------------------------------- Balanced, Enclosed, 2-Vane • Motor Service Factor----------------- 1.20 REV 04/01/15 K4VN(X) Features and Benefits 1. Watertight Cable Entrance Agency-approved, watertight strain relief cord grips with compression grommets protects outer cord jacket. Epoxy-filled inner cord cap provides anti-wicking moisture protection to the motor even if power cable is cut or damaged. 40’ UL power & control cords. 2. Modular Pump Design 1 Commonality of parts across the Keen product line minimizes the amount of parts required for servicing. Heavy-duty ASTM A48, Class 30 cast iron components. 3. Strong Motor (U.S. Motor Manufacturer) Powerful high-torque motor for strong pumping. 208/230 Volt, 1-phase 208/230/460 Volt, 3-phase Slip-Fit stator efficiently transfers heat to cast housing. Class F construction with overload protection in oil-filled chamber for cool operation and long motor life. 3a. Oil 2 3 Proprietary Keen oil ensures industry-low operating temperatures. 4 4. Solid 3-Bearing Support Motor / Pump shaft securely held with upper and lower ball bearings, plus additional sleeve bearing in lower seal chamber. Rated for 50,000 hour B-10 life. 5. Severe Duty Dual Mechanical Seals 5 6 Dual silicon carbide mechanical shaft seals provide twice the moisture and grit protection for the motor. Dual seals are housed in a secondary oil-filled seal chamber. Tougher silicon carbide seals better handle sand, grit and abrasive materials. 6. Moisture Detection Seal leak probe signals alarm in control panel for scheduled maintenance. 7. High Efficiency Hydraulic Design Highly efficient enclosed 2-vane impeller easily passes 3” diameter solids without blockage. The strong ductile iron impeller features backside pump-out vanes, keeping lower seal clean and pressure-compensated for longer life. Dynamically balanced for smooth, quiet operation and long bearing life. 8. Standard Flange Connection 4“ Horizontal, Class 125 ANSI discharge flange. Industry standard, 8-bolt pattern. 9 7 8 9. High Performance Wear Ring Assists impeller in providing higher performance efficiencies and prevention of recirculation losses. Bronze ring will not corrode or deteriorate from liquid being pumped. Bronze ring reduces wear to stronger ductile iron impeller in sandy or gritty applications. Easily serviceable and replaceable. 471E State Route 250 East . Ashland, Ohio 44805 419.207.9400 fax 419.207.8031 www.keenpump.com REV 04/01/15 Section Date Pump Series K4VN ENCLOSED JULY 2013 4” SUBMERSIBLE SEWAGE PUMPS DIMENSIONAL DATA Note: All dimensions in inches unless noted. Dimensions may vary due to normal manufacturing tolerances. File: K4VN Dimensions Section Date Pump Series K4VN ENCLOSED JULY 2013 4” SUBMERSIBLE SEWAGE PUMPS LIFTOUT DIMENSIONAL DATA Notes: 1. All dimensions in inches unless noted. 2. Discharge flange ANSI Class 125 unless noted. 3. Absolute minimum and recommended minimum submergence levels noted. 4. Discharge base elbow must be placed above sump bottom as noted. 5. Dimensions may vary due to normal manufacturing tolerances. 6. If discharge pipe is larger than discharge elbow, eccentric reducer must be used limited to 2X larger maximum. File: K4VN Liftout Dimensions Section Date Pump Series K4VN ENCLOSED JULY 2013 4” SUBMERSIBLE SEWAGE PUMPS SIMPLEX INSTALLATION DIMENSIONAL DATA Notes: 1. All dimensions in inches unless noted. 2. Refer to pump dimension and liftout dimension sheets for more details. 3. Recommended minimum submergence levels noted. 4. Discharge base elbow must be placed above sump bottom as noted. 5. Dimensions may vary due to normal manufacturing tolerances. 6. If discharge pipe is larger than discharge elbow, eccentric reducer must be used limited to 2X larger maximum. File: K4VN Install Dimensions Section Date Pump Series K4VN ENCLOSED JULY 2013 4” SUBMERSIBLE SEWAGE PUMPS DUPLEX INSTALLATION DIMENSIONAL DATA Notes: 1. All dimensions in inches unless noted. 2. Refer to pump dimension and liftout dimension sheets for more details. 3. Recommended minimum submergence levels noted. 4. Discharge base elbow must be placed above sump bottom as noted. 5. Dimensions may vary due to normal manufacturing tolerances. 6. If discharge pipe is larger than discharge elbow, eccentric reducer must be used limited to 2X larger maximum. File: K4VN Install Dimensions
Similar documents
KW5 cuts - Keen Pump
KW5 Specifications Pump Model – Pump shall be of the submersible centrifugal type, 1/2 HP KEEN KW5 Series. The pump shall easily pass 2” diameter solids through the pump end without jamming and ex...
More informationKW cuts - Keen Pump
The motor shall have two heavy duty ball bearings to support the pump shaft, taking radial and thrust loadings. Ball bearings shall be designed for a minimum 50,000 hours B-10 life. The stator shal...
More information