PS Printer Driver

PS Printer Driver
for Windows 7
User’s Manual
Regarding this manual
This manual explains how to install Windows PS Printer Driver and how to use it.
This PS Printer Driver can be used with Microsoft Windows 7.
NOTE:
To use KM-4800w-PS Printer Driver, “UG-32B” Option License is required.
1
Index
1.
1.1.
1.2.
1.3.
1.4.
1.5.
2.
INSTALLATION METHOD................................................................................3
Install TCP/IP Port......................................................................................................................................................... 3
Add “KM-4800w TCP/IP Port”.................................................................................................................................... 7
Add Printer....................................................................................................................................................................11
About Printer Port........................................................................................................................................................18
About reinstall of Printer..............................................................................................................................................20
SETTING ITEM OF PRINTER DRIVER ....................................................25
2
1.
1.1.
Installation Method
Install TCP/IP Port
NOTE:
If KM-4800wEN printer is already installed on your system, TCP/IP Port
installation has been completed at the same time.
Please go to [1.3 Add Printer] to continue the printer installation.
1. Insert Installation Disk in CD-ROM drive.
2. Open “(the optical drive)\ Option\PS_Printer_UG-32\PrinterPort\”.
Right-click on “KM4800wTcpMon_xxx.exe” and select “Run as administrator”.
(xxx is the version)
[Use Account Control] message will appear. Click “Yes”.
3. Click “OK”.
3
4. Click “Next”.
5. Click “Install”.
4
6. Please wait while the wizard is installing the components.
7. Click “Finish”.
5
If the following message appears, click “This Program installed correctly”.
TCP/IP port installation is completed.
6
1.2.
Add “KM-4800w TCP/IP Port”
1. Point “Start Menu” and click “Devices and Printers”.
2. Click “Fax” and then “Print server properties”.
7
3. “Print Server Properties” is displayed.
Open “Ports” and click “Change Port Settings”.
4. Click “Add Port”.
8
5. Select “KM-4800w TCP/IP Port” and click “New Port”.
6. Enter the KM-4800w’s IP address or host name.
Click “OK”.
7. Click “Close”.
9
8. Confirm that “KM-4800w TCP/IP Port” is displayed in the list. Click “Close”.
Adding “KM-4800w TCP/IP Port” is completed.
10
1.3.
Add Printer
1.
In “Devices and Printers”, click “Add a printer”.
2. Choose “Add a local printer”.
11
3. Choose “Use an existing port:” and then select “KM-4800w:192.168.100.10 (KM4800w TCP/IP Port)” in the pull down menu. Click “Next”.
4. Click “Have Disk”.
12
5. Click “Browse”.
6. Specify “K48 PSEN.INF” at “(the optical drive)\Option\PS_Printer_UG32\PS_PrinterDriver\EN\”.
Click “Open”.
English: specify \Option\PS_Printer_UG-32\PS_PrinterDriver\EN\ K48PSEN.INF
French: specify \Option\PS_Printer_UG-32\PS_PrinterDriver\FR\ K48PSFR.INF
German: specify \Option\PS_Printer_UG-32\PS_PrinterDriver\DE\ K48PSDE.INF
Italian: specify \Option\PS_Printer_UG-32\PS_PrinterDriver\IT\ K48PSIT.INF
Spanish: specify \Option\PS_Printer_UG-32\PS_PrinterDriver\ES\ K48PSES.INF
13
7. Click “OK”.
8. Click “Next”.
14
9. If KM-4800w PS Printer Driver is already installed on your system, the following
screen appears.
Select “Replace the current driver” and click “Next”.
10. Printer name can be changed at your option.
Click ”Next”.
15
11. Check “Always trust software from “KYOCERA MITA Corporation”.” and click “Install”.
12. Click “Finish”.
16
13. Confirm that “KM-4800wEN-PS” is added in “Printers and Faxes”.
Installation of printer has been finished.
17
1.4.
About Printer Port
In “Devices and Printers”, select “KM-4800wEN-PS” and click “Print server properties”.
Open “Ports” and then click “Change Port Settings”.
18
Select “KM-4800w TCP/IP Port” and then click “Configure Port”.
The following information is indicated.
You do not have to change any of the above settings in usual case.
Change these settings when KM-4800w does not wake up correctly from the Power
Save Mode caused by the network settings.
MAC Address: MAC Address of output printer
Broad Cast Address: An address used to send the data to all PC on the network
Magic Boot Port: Port number to send the data
Timeout: Timeout when no response comes from the output printer
Retry: Number of retry when no response comes from the output printer
19
1.5.
About reinstall of Printer
In “Devices and Printers”, select a KM-4800wEN-PS you want to remove and then right
click “Remove device”.
Click “Yes”.
20
In “Devices and Printers”, click “Fax” icon and then click “Print server properties”.
Open “Drivers” and then click “Change Driver Settings”.
21
Select “KM-4800wEN-PS” and then click “Remove”.
Select “Remove driver and driver package” and click “OK”.
Click “Yes”.
22
Click “Delete”.
Click “OK”.
If the removal of the driver is failed, reboot the PC, and then try to remove the driver
again.
23
Click “Close”.
Now the system is ready to be reinstalled KM-4800wEN-PS.
24
2.
Setting item of Printer Driver
If the setup conditions of the application is not correct, documents may not be printed
properly.
Point “Start Menu” and click “Devices and Printers”.
Select the printer you have installed by right clicking, and then open “Printing
Preferences”.
25
Each setting item in “Layout” Tab is explained in below.
< Orientation >
Orientation of paper can be selected.
“Rotated Landscape” rotates a “Landscape” image 180 degrees around.
<Page Order>
“Front to Back” outputs a multiple page file from the first page to the last page.
“Back to Front” outputs a multiple page file from the last page to the first page.
<Page Format>
Multiple images can be printed on 1 sheet of printing media.
16 images is the maximum number of images available to print on 1 sheet of printing
media.
“Draw Borders” surrounds all the images with borders.
26
Each setting item in “Paper/Quality” Tab is explained below.
<Tray Selection>
<Paper Source>
The source of paper can be selected.
“Automatically Select” is equivalent to “Auto”.
<Media>
The type of printing media can be selected.
27
Each setting item in “Advanced” is explained below.
<Paper/Output>
<Paper Size>
Specify the size of paper used for printing.
If “Custom Size” is selected in the above setting, the following dialog is
indicated.
A paper size can be specified at your option within the following range.
Width: 210 mm to 914.4 mm
Height: 297 mm to 10000 mm
28
<Copy Count>
Number of prints can be specified.
Available count ranges from 1 to 9999 but the guarantee range of proper
operation is from 1 to 999.
Checking “Collate” enables to print sets with collating.
<Graphic>
<Print Quality>
Printing resolution can be specified.
The printing resolution is normally set to 600dpi.
If there is any problem on a print, the printing resolution can be changed to
300dpi or 200 dpi.
<Scaling>
The printing image is enlarged or reduced according the specified value.
Available percentage ranges from 1 to 1000 but the guarantee range of proper
operation is from 20 to 500.
<True Type Font>
True Type Font options can be specified.
The option is normally set to “Substitute with Device Font”.
If some special characters are lost or printed incorrectly, set it to “Download as
Softfont”.
<Document Options>
<Advanced Printing Features>
This option should be always set to “Enabled”.
<Pages per Sheet Layout>
Page Layout option can be specified for “Pages per Sheet”.
29
<PostScript Options>
<PostScript Output Option>
This should be normally set to “Optimize for Speed”.
<True Type Font Download Option>
This should be normally set to “Automatic”.
<PostScript Language Level>
This should be set to “Level 3”.
<Send PostScript Error Handler>
This should be normally set to “No”.
<Mirrored Output>
A mirror image can be printed when “Yes”.
<Negative Output>
A negative Image can be printed when “Yes”.
<Printer Features>
<Output Size>
The printing image is automatically enlarged or reduced just to fit the
paper size selected on “Output Size”.
30
PS Printer Driver for Windows 7 User’s Manual
2010. 1 Rev. 1.0
The Copyright Act protects this manual.
It is prohibited to copy or duplicate all or a part of this manual without permission.
31