Approved Ironmongery for the Railway Environment

Transcription

Approved Ironmongery for the Railway Environment
Approved Ironmongery
for the Railway Environment
Version 5
A division of Turentek
Contents
Introduction
Hinges
Door Furniture
Door Closers
Lockcases
Electric Strikes
Speech Panels with Call Button
Panic Bolts
Secure Suite Deadlock
Collapsible Gate Device
Miscellaneous
Key Cabinets and Boxes
Typical Doorset Arrangements
Suppliers
Manufacturers
Page ii
1
2
4
20
29
41
42
45
50
51
54
58
59
65
65
Introduction
DOOR FURNITURE METHODOLOGY
This catalogue has been compiled in response to the requirements of the Fire Precautions Act (Sub-Surface
Railway Stations) Regulations1401:1989, The EC Construction Products Directive and the Loss Prevention
&RXQFLO·V/RVV3UHYHQWLRQ6WDQGDUG/36,VVXH6SHFLÀFDWLRQIRUWHVWLQJDQGFODVVLI\LQJWKHEXUJODU\
resistance of building components, strong points and security enclosures.
The catalogue must be read in conjunction with Section P21 Ironmongery of the project General BuilderVZRUN6SHFLÀFDWLRQZKLFKGHÀQHVWKHSHUIRUPDQFHFULWHULDWREHPHW
7KHVSHFLÀFDWLRQRIGRRUIXUQLWXUHWREHXVHGRQWKH8QGHUJURXQGVKRXOGPHHWWKHIXQFWLRQDOUHTXLUHPHQW
RIWKHURRPIRUZKLFKLWLVEHLQJVSHFLÀHG$Q(TXLSPHQW5RRPZLWKRQHDFFHVVPHDQVRIHVFDSHZLOO
require a door that opens out, if into a public area has a vision panel and a panic function lock (not a panic
EROWDVIRUSXEOLFPHDQVRIHVFDSH$QRIÀFHPD\UHTXLUHDPRUWLVHODWFKPRUWLVHORFNLQJODWFKRUGHDG
bolt depending on the function, location and security requirement
Lockcases are all mortised into the door leaf, rim locks offer little physical security and their use should be
avoided. All lockcases are of steel construction, no component part shall have a melting point of less than
850c. The access, escape and security function of each lockcase is fully described. The hand required must
EHGHVFULEHGDVYLHZHGIURPWKHKLQJHEXWWVLGHRIWKHGRRU/+5+
)DFHÀ[HGIXUQLWXUHKDVEHHQFDWDORJXHGLQWZRYDULHWLHVJUDGHVWDLQOHVVVWHHOIRUSRVWZDUFRQVWUXFtions and BMA gunmetal for pre-war, listed and heritage constructions.
2SWLRQVIRUWKHVL]HRISXOOKDQGOHDUHJLYHQIRUVSHFLÀFDWLRQDFFRUGLQJWRGRRUOHDIVL]H
Closers are shown to cater for the varying conditions with adjustable power sizes. The selection must be
appropriate to the requirement.
$OOFORVHUVVKDOOEHÀWWHGWRWKHQRQSXEOLFVLGHRIWKHGRRUWRSUHYHQWYDQGDOLVP.LFNLQJSODWHVDUHVKRZQ
for pre and post war constructions. The selection must be appropriate for the chosen furniture.
%DUUHOEROWVLQFOXVLYHRIGXVWH[FOXGLQJVRFNHWVIUDPHVRFNHWVDQGWRSUHFHLYLQJSODWHVDUHVKRZQIRUXVH
on the inactive leaf of double door sets.
Hinges are shown; the number to be used on each door leaf is dependent on leaf size and weight. Design
weight loading must be taken into consideration in conjunction with the selected closer.
)XUQLWXUHDQGVLJQVVKDOOEHÀWWHGWRGRRUVDQGIUDPHVLQDFFRUGDQFHZLWKWKHLQFOXGHGLOOXVWUDWLRQV
0DQXIDFWXUHUVDQGVXSSOLHUVQDPHGZLWKLQWKLVFDWDORJXHDUHLGHQWLÀHGDVFDSDEOHRIPHHWLQJWKHSHUIRUmance requirements described herein.
The Part No. reference should be used in conjunction with a Door and Ironmongery Schedule.
5TH EDITION - 2013
'RRU&ORVHUUDQJHH[SDQGHGWRDFFRPPRGDWHVHOHFWLRQE\GRRUZLGWK1HZ&ROODSVLEOH*DWH'HYLFHV
DGGHG$'LJLWDO$FFHVV.H\3DGKDVEHHQDGGHGIRUURRPVQRWVXEMHFWWRSXEOLFDFFHVVDQGRWKHU.H\SDGV
updated.
This edition has been prepared with assistance from Suppliers and Manufacturers without whose detailed
understanding of functional requirements and knowledge of architectural ironmongery, assembly of this
LQIRUPDWLRQZRXOGEHH[WUHPHO\GLIÀFXOW
7KHFDWDORJXHPD\QRWEHH[KDXVWLYHRIDOOUHTXLUHPHQWVDGYLFHDQGDVVLVWDQFHZLWKWKHSUHSDUDWLRQRI
VFKHGXOHVPD\EHREWDLQHGLQWKHÀUVWLQVWDQFHIURPWKH'LVFLSOLQH'HVLJQ(QJLQHHU
Page 1
Hinges
Part No. A1
High performance door hinge with concealed bearings
Size:
PP[PP[PP
Material:
$XVWHQLWLFVWDLQOHVVVWHHO*UDGH(1
Finish:
6WDQGDUGÀQLVK6DWLQEUXVKHGVWDLQOHVVVWHHO
Alternative: Electrophoretic simulated bronze.
Standards:
Independently tested to EN 1935
*UDGH&HUWLÀUHDSSURYHGDQG&(PDUNHGIRUÀUHGRRU
usage.
(17HVWFHUWLÀFDWH1R7&&
&(FHUWLÀFDWH&3'$&66
6SHFLÀFDWLRQ
0D[LPXPDGMXVWHGGRRUZHLJKWNJV
Minimum door thickness 44mm
25 year performance guarantee.
Maintenance free concealed bearings.
Precision template drilled for use on steel or timber door
sets.
6FUHZVL]HPP[1R7ZLQIDVW3R]LKHDG0[PP
for metal doors.
Markings: TfL-A1 on hinge leaf.
Radius corners to special order.
Advisory:
Select finish complimenting chosen furniture.
Select A1 for design loads up to 120kgs and high
frequency application.
Page 2
Hinges
Part No. A4
High performance door hinge with concealed bearings
Size:
PP[PP[PPRYHUVL]HGRRUV
Material:$XVWHQLWLFVWDLQOHVVVWHHO*UDGH(1
10088
Finish:
6WDQGDUGÀQLVK6DWLQEUXVKHGVWDLQOHVVVWHHO
Alternative: Electrophoretic simulated bronze
Standards:
,QGHSHQGHQWO\WHVWHGWR(1*UDGH&HUWLÀUHDSSURYHGDQG&(PDUNHGIRUÀUHGRRUXVDJH
6SHFLÀFDWLRQ
0D[LPXPDGMXVWHGGRRUZHLJKWNJV
Minimum door thickness 44mm
25 year performance guarantee.
Maintenance free concealed bearings.
Precision template drilled for use on steel or timber door
sets.
6FUHZVL]HPP[1R7ZLQIDVW
3R]LKHDG0[PPIRUPHWDOGRRUV
Markings: TfL-A4 on hinge leaf.
Radius corners to special order.
Advisory:
Select finish complimenting chosen furniture.
Select A4 for design loads up to 160kgs and high
frequency application.
Page 3
Door Furniture
Part No. F01
Lever/lever latch furniture – un-sprung on un-pierced backplate with solid spindle and security
EDFNWREDFN7RU[KHDGÀ[LQJVFUHZV
Size:
/HYHUKDQGOHPP[PPGLD
%DFNSODWHPP[PP[PP
6SLQGOHVROLGPP[PPVT
Material:
/HYHUEDFNSODWH(1VWDLQOHVVVWHHO
Spindle: Mild steel case hardened
Fixings:
VWDLQOHVVVWHHOPDOHDQGIHPDOHEDFNWREDFNEROW
WKURXJKÀ[LQJVZLWK7RU[KHDG*UXEVFUHZVSLQGOHÀ[LQJ
Finish:
Lever and backplate: Satin polished
Spindle: Zinc passivated
Standards:
From approved manufacture list.
6SHFLÀFDWLRQ
To suit L01 latch.
Advisory:
Use in intercommunicating office doors where no
security is required.
Requires L01 L/R mortise latch.
Page 4
Door Furniture
Part No. F04
Lever/lever latch furniture – un-sprung on euro pierced backplate with split spindle and security
EDFNWREDFN7RU[KHDGÀ[LQJVFUHZV
Size:
/HYHUKDQGOHSLHFHPP[PPGLDP
%DFNSODWHPP[PP[PP
6SLQGOHPP[PPVT
Material:
/HYHUEDFNSODWHVWDLQOHVVVWHHO
Spindle: Mild steel case hardened
Fixings:
PDOHDQGIHPDOHEDFNWREDFNEROWWKURXJKÀ[LQJVZLWK
7RU[KHDG*UXEVFUHZVSLQGOHÀ[LQJ
Finish:
Lever and backplate: Satin polished
Spindle: Zinc passivated
Standards:
From approved manufacture list.
6SHFLÀFDWLRQ
To suit L03 and L04 panic locks.
Advisory:
Use in secure staff accommodation areas, e.g.: offices, cash handling rooms.
Requires L03 L/R or L04 L/R panic lock cases.
Page 5
Door Furniture
Part No. F04X
Lever/lever latch furniture – un-sprung on euro pierced backplate with solid spindle and security
EDFNWREDFN7RU[KHDGÀ[LQJVFUHZV
Size:
/HYHUKDQGOHPP[PPGLDP
%DFNSODWHPP[PP[PP
6SLQGOHVROLGPP[PPVT
Material:
/HYHUEDFNSODWHVWDLQOHVVVWHHO
Spindle: Mild steel case hardened
Fixings:
VWDLQOHVVVWHHOPDOHDQGIHPDOHEDFNWREDFNEROWWKURXJK
À[LQJVZLWK7RU[KHDG*UXEVFUHZVSLQGOHÀ[LQJ
Finish:
Lever and backplate: Satin polished
Spindle: Zinc passivated
Standards:
From approved manufacture list.
6SHFLÀFDWLRQ
To suit L12 sash locks
Advisory:
Use on office, cupboard or storeroom doors where
panic escape is not required.
Requires L12 L/R mortise sash lock.
Page 6
Door Furniture
Part No. F04WC
Lever/lever latch furniture – un-sprung on thumb turn and release backplate with solid spindle
DQGVHFXULW\EDFNWREDFN7RU[KHDGÀ[LQJVFUHZV Size:
/HYHUKDQGOHPP[PPGLDP
%DFNSODWHPP[PP[PP
6SLQGOHVROLGPP[PPVT
Material:
/HYHUEDFNSODWHVWDLQOHVVVWHHO
Spindle: Mild steel case hardened
Fixings:
PDOHDQGIHPDOHEDFNWREDFNEROWWKURXJKÀ[LQJVZLWK
7RU[KHDG*UXEVFUHZVSLQGOHÀ[LQJ
Finish:
Lever and backplate: Satin polished
Spindle: Zinc passivated
Standards:
From approved manufacture list.
6SHFLÀFDWLRQ
To suit L13 bathroom locks.
Advisory:
Use in staff and public WC doors.
Requires L13 bathroom lock.
Use in conjunction with L17 mortise deadbolt and
F05A escutcheons to allow for isolation during
maintenance.
Page 7
Door Furniture
3DUW1R)VXIÀ['IRUDGGLWLRQDOSXOOKDQGOHIRUGRXEOHGRRUVHW
Lever/pull furniture – un-sprung on euro pierced backplate with threaded solid spindle and secuULW\EDFNWREDFN7RU[KHDGÀ[LQJV
Size:
/HYHUKDQGOHPP[PPGLDP
/HYHUEDFNSODWHPP[PP[PP
3XOOKDQGOHPP[PPGLDP
3XOOKDQGOHEDFNSODWH)PP[PP[PP
)PP[PP[PP
)PP[PP[PP
)PP[PP[PP
6SLQGOHPP[PPVTWKUHDGHG
Material:
/HYHUEDFNSODWHVWDLQOHVVVWHHO
3XOOKDQGOHEDFNSODWHVWDLQOHVVVWHHO
Spindle: Mild steel case hardened
Fixings:
VWDLQOHVVVWHHOPDOHDQGIHPDOHEDFNWREDFNEROWWKURXJK
À[LQJVZLWK7RU[KHDG
Finish:
Lever & back plate: Satin polished
Pull & back plate: Satin polished
Spindle: Zinc passivated
Standards:
From approved manufacture list
6SHFLÀFDWLRQ
7RVXLW/SDQLFORFNV/DXWRÀUHSDQLFORFNV//
lockcases or L01 lockcase
Advisory:
Use on equipment room and public facing doors.
Requires L02 L/R mortise sash lock with panic
function E deadbolt and latch, L14 L/R mortise
sash lock auto-fire panic action deadbolt and latch.
or L01L/R, L16 L/R or L19 for security access
systems..
Different backplates, sizes and configurations are
available in this range. Consult supplier.
Page 8
Door Furniture
Part No. F14
Handle arrangement to suit drivers ‘J’ key on plain un-pierced lever handle plate and lipped exterQDOSODWHZLWKFRQLFDONH\VKURXGÀ[HGZLWKVHFXULW\EDFNWREDFN7RU[À[LQJVFUHZV Size:
/HYHUKDQGOHPP[PPGLDP
%DFNSODWHPP[PP[PP
6SLQGOH6SHFLDOWDSHUHGVROLGPP[PPVT
Material:
/HYHUFRQHEDFNSODWHVWDLQOHVVVVWHHO
Spindle: Mild steel case hardened
Fixings:
VWDLQOHVVVWHHHOPDOHDQGIHPDOHEDFNWREDFNWKURXJK
À[LQJVZLWK7RU[KHDG
Finish:
Lever & back plates: Satin polished
Spindle: Zinc plated
Standards:
From approved manufacture list
6SHFLÀFDWLRQ
To suit L01 latch
Advisory:
For use on auto-phone kiosks, driver’s toilets and
access.
Requires L01 latch.
Page 9
Door Furniture
Part No. F15
Lock Bezel to suit driver’s J key, on plain plate with conical key shroud
Size:
3ODWHPP[PP
Material:
VWDLQOHVVVWHHO
Finish:
Satin polished.
Fixings:
PP[1R7RU[KHDGFRXQWHUVXQNVFUHZV
Standards:
From approved manufacture list.
Advisory:
To act as guide for key on hinged doors and
gates to protect keyway.
For use on auto phone kiosks, driver’s toilets and
access.
Alternative when F14 door furniture unsuitable.
Page 10
Door Furniture
Part No. WC1
DDA compliant mortice bathroom door furniture
/HYHUODWFKIXUQLWXUH'RXEOHVSLQGOH''$FRPSOLDQWVHFXULW\
EDFNWREDFN7RU[KHDGÀ[LQJVFUHZV
6SHFLÀFDWLRQ
Lever latch furniture, unsprung with backplates, solid spindle
DQGUHGJUHHQRFFXSLHGYDFDQF\EROWLQGLFDWLRQH[WHUQDOWRRO
release provision in case of emergency.
Entry:
Free entry in the case of vacancy by lever handle, internal handle provides lifting to vertical position securing WC bolt during
occupancy.
Exit:
Internal single handed action downward to release bolt and
ODWFKHQDEOLQJH[LW
external view
6L]H/HYHUKDQGOH[GLD
Finish: Lever handles Plascoat PPA571 colour compliant with
DDA requirement (select from Plascoat range)
%DFNSODWHV[[
Backplate Satin polished
6SLQGOH6ROLG[VT6SLQGOH=LQFSDVVLYDWHG
Material:
/HYHUDQGEDFNSODWHVWDLQOHVVVWHHO
6SHFLÀFDWLRQ7RVXLWEDWKURRPORFNV
Spindle Mildsteel
)L[LQJV
VWDLQOHVVVWHHOPDOHDQGIHPDOHEDFNWREDFNEROWWKURXJK
À[LQJVZLWK7RU[KHDG
internal view
Advisory:
use in DDA WC’s.
Requires L18 L/R mortise bathroom lock. Use in
conjunction with L17 mortise deadlock and F05 A
escutcheons to allow for isolation of toilet during
maintenance
Page 11
Lock with Emergency Override
Part No. LEO1/LEO2
Key entry lock, compliant for use on BS EN 1125 and BS EN 179 panic and emergency exit doors
/(2VXUIDFHPRXQWHG
Material: Bronze body, stainless steel inner components
Finish: Chrome plated
Cylinder: Round
/(2UHFHVVÀWWHG
Material: Stainless steel body, stainless steel inner components
Finish: Bright polished
Cylinder: Round
LEO1 - surface mounted
6SHFLÀFDWLRQ
Operation: By inserting key and turning, then turning lever
KDQGOHWRUHOHDVHPXOWLSOHSDQLFEROWVÀWWHGWRWKHLQQHU
face of door.
/(2UHFHVVÀWWHG
Advisory:
Use in conjunction with PES2 Panic Exit System
and CGD1A active gate lock requiring key access.
Key retained facility available, ensures auto-relocking
Page 12
Lock with Emergency Override
Part No. LEO3/LEO4
Key entry lock, compliant for use on BS EN 1125 and BS EN 179 panic and emergency exit doors
/(2VXUIDFHPRXQWHG
Material: Bronze body, stainless steel inner components
Finish: Chrome plated
&\OLQGHU(XURSURÀOH
/(2UHFHVVÀWWHG
Material: Stainless steel body, stainless steel inner components
Finish: Bright polished
&\OLQGHU(XURSURÀOH
LEO3 - surface mounted
6SHFLÀFDWLRQ
Operation: By inserting key and turning, then turning lever
KDQGOHWRUHOHDVHPXOWLSOHSDQLFEROWVÀWWHGWRWKHLQQHU
face of door.
/(2UHFHVVÀWWHG
Advisory:
Use in conjunction with PES2 Panic Exit System
and CGD1A active gate lock requiring key access.
Key retained facility available, ensures auto-relocking
Page 13
Door Furniture
Part No. F05 A/B/C/D
3DLURI(XURSURÀOHSLHUFHGHVFXWFKHRQVFRPSOHWHZLWKEROWWKURXJKÀ[LQJVFUHZV
Size:
$%PPGLD[PP&PPGLD[PP'PP[
2mm
Finish:
F05A - Satin polished
F05B - RBMA
)&'666
Material:
VWDLQOHVVVVWHHO or RBMA Gunmetal
Fixings
)$%0DOHDQGIHPDOHEDFNWREDFNEROWWKURXJKÀ[LQJV
ZLWK7RU[KHDGVFUHZV
)&'6XLWDEOHÀ[LQJVWRVXLWGRRUVHW
F05A
F05C
Page 14
F05B
F05D
Advisory:
To be used when no lever furniture is required,
RBMA on listed heritage sites. Use in cupboard or
passage doors where panic escape is not required.
Use with L17 mortise deadbolt.
F05A/B bolt through back to back.
F05C/D supplied as single items when only external key access required.
Door Furniture
Part No. F08
([WHUQDODFFHVVGHYLFHZLWK(XURSURÀOHDSHUWXUHDYDLODEOHZLWKHLWKHUNQRERUOHYHUKDQGOH
Compliant for use on BS EN179 and BS EN 1125, panic and emergency exit doors.
Advisory:
Use in conjunction with Panic Bar F07 and optional
free or locked configuration is required. Access
from outside available either by inserting key and
turning knob or, in unlocked mode, by turning knob
only.
Page 15
Door Furniture
Part No. F22
/HYHUOHYHUIXUQLWXUHXQVSUXQJOHYHUKDQGOHVRQURVHVFRPSOHWHZLWKSODLQVSLQGOHDQGÀ[LQJ
screws.
Size:
/HYHUKDQGOHPP[PP
5RVHPPGLDP[PP
6SLQGOHVROLGPPVT[PP
Material:
Lever handle: Gunmetal
Rose: Gunmetal
Spindle: Mild steel
Fixings:
0DOHDQGIHPDOHEDFNWREDFNEROWWKURXJKÀ[LQJV
ZLWK7RU[KHDG
Finish:
Lever handle: RBMA
Rose: RBMA
Spindle: Zinc passivated
Standards:
From approved manufacture list
6SHFLÀFDWLRQ
To suit L01 latch locks
Advisory:
For listed/ heritage/ pre-war constructions.
Use in intercommunicating office doors where no
security is required.
Requires L01R/Lmortise latch.
Page 16
Door Furniture
Part No. F25
/HYHUOHYHUIXUQLWXUHXQVSUXQJOHYHUKDQGOHVRQURVHVFRPSOHWHZLWKVSOLWVSLQGOHDQGÀ[LQJ
VFUHZVSDLUHXURSURÀOHSLHUFHGHVFXWFKHRQVFRPSOHWHZLWKÀ[LQJVFUHZV
Size:
/HYHUKDQGOHPP[PP
5RVHPPGLDP[PP
6SLQGOHPPVT[PP
SLHFH(VFXWFKHRQPPGLDP[PP
Material:
Lever handle: Gunmetal
Rose: Gunmetal
Spindle: Mild steel
Escutcheon: Gunmetal
Fixings:
0DOHDQGIHPDOHEDFNWREDFNEROWWKURXJKÀ[LQJVZLWK7RU[
head.
Finish:
Lever handle: RBMA
Rose: RBMA
Spindle: Zinc passivated
Escutcheon: RBMA
Standards:
From approved manufacture list
6SHFLÀFDWLRQ
7RVXLW//5RU//5PRUWLFHVDVKORFN
Advisory:
For listed/ heritage/ pre-war constructions.
Use on office, cupboard or storeroom doors where
panic escape is required.
Requires L03 L/R or L04 L/R mortice sash lock
Page 17
Door Furniture
Part No. F25X
/HYHUOHYHUIXUQLWXUHXQVSUXQJOHYHUKDQGOHVRQURVHVFRPSOHWHZLWKVROLGVSLQGOHDQGÀ[LQJ
VFUHZVSDLUHXURSURÀOHSLHUFHGHVFXWFKHRQVFRPSOHWHZLWKÀ[LQJVFUHZV
Size:
/HYHUKDQGOHPP[PP
5RVHPPGLDP[PP
6SLQGOHVROLGPPVT[PP
(VFXWFKHRQPPGLDP[PP
Material:
Lever handle Gunmetal
Rose Gunmetal
Spindle Mild steel
Escutcheon Gunmetal
Fixings:
0DOHDQGIHPDOHEDFNWREDFNEROWWKURXJKÀ[LQJVZLWK7RU[
head.
Finish:
Lever handle Real BMA
Rose Real BMA
Spindle Zinc passivated
Escutcheon Real BMA
Standards:
From approved manufacture list
6SHFLÀFDWLRQ
To suit L12 sash locks
Advisory:
For listed/ heritage/ pre-war constructions.
Use on cupboard or storeroom doors where panic
escape is not required.
Requires L12 L/R mortise lock deadbolt and latch.
Page 18
Door Furniture
Part No. F44/1/2/3
/HYHUOHYHUIXUQLWXUHXQVSUXQJOHYHUKDQGOHVRQURVHVFRPSOHWHZLWKVSOLWVSLQGOHDQGÀ[LQJ
VFUHZVSDLUHXURSURÀOHSLHUFHGHVFXWFKHRQVFRPSOHWHZLWKÀ[LQJVFUHZV8VHVXIÀ['IRUDGditional pull handle for double leaf doorset.
Size:
Finish:
/HYHUKDQGOHPP[PP
Lever handle: Real BMA
5RVHPPGLDP[PP
Rose: Real BMA
6SLQGOHVROLGPPVT[PP
Spindle: Zinc passivated
3XOOKDQGOHPP[PP
Pull handle: Real BMA
(VFXWFKHRQPPGLDP[PP
Escutcheon: Real BMA
Material:
Standards:
Lever handle: Gunmetal
7R7I/VSHFLÀFDWLRQIURPDSSURYHGPDQXIDFWXUHOLVW
Rose: Gunmetal
Spindle: Mild steel
6SHFLÀFDWLRQ
Pull handle: Gunmetal
7RVXLW/SDQLFORFNV//DXWRÀUHSDQLFORFNVRU/
lockcase
Escutcheon: Gunmetal
Fixings:
0DOHDQGIHPDOHEDFNWREDFNEROWWKURXJKÀ[LQJVZLWK7RU[KHDG
Advisory:
Use on equipment room and public facing doors.
Requires L02 L/R mortise sash lock with panic
function E deadbolt and latch, L14 L/R mortise
sash lock auto-fire panic action deadbolt and latch.
or L01L/R, L16 L/R or L19 for security access
systems..
Different backplates, sizes and configurations are
available in this range. Consult supplier.
Page 19
C6 DOOR CLOSER
Cam Action slide arm door closer for door mounting pull side of door
&DPDFWLRQGRRUFORVHUZLWKIXOOFRYHUFRQFHDOHGÀ[LQJVDQGFXVKLRQHGOLPLWVWD\
Standards: &(PDUNHGWR(1&HUWLÀUHDSSURYHGIRUWLPEHUÀUHGRRUVKRXUVDQGPHWDOÀUHGRRUV
hours).
Size: power adjustable size EN 2-4 to suit doors up to 1100mm
Finishes; silver (ses), stainless steel (sss)
Marking: &ZLWKURXQGHO
Page 20
Advisory:
Closers are always to be fixed to the inside (unprotected) face of door leaf.
C7 DOOR CLOSER
Cam Action slide arm door closer for door mounting push side of door
&DPDFWLRQGRRUFORVHUZLWKIXOOFRYHUDQJOHEUDFNHWFRQFHDOHGÀ[LQJVDQGFXVKLRQHGOLPLWVWD\
Standards: &(PDUNHGWR(1&HUWLÀUHDSSURYHGIRUWLPEHUÀUHGRRUVKRXUVDQGPHWDOÀUHGRRUV
hours).
Size: power adjustable size EN 2-4 to suit doors up to 1100mm
Finishes; silver (ses) stainless steel (sss)
Marking: C7 with roundel
Advisory:
Closers are always to be fixed to the inside (unprotected) face of door leaf.
Page 21
C8 DOOR CLOSER
Cam Action electro-magnetic hold open slide arm door closer for door mounting pull side of door
&DPDFWLRQGRRUFORVHUZLWKIXOOFRYHUHOHFWURPDJQHWLFKROGRSHQVOLGHFKDQQHODQGFRQFHDOHGÀ[LQJV
Standards:&(PDUNHGWR(1&HUWLÀUHDSSURYHGIRUWLPEHUÀUHGRRUVKRXUVDQGPHWDOÀUHGRRUV
hours).
Size: power adjustable size EN 2-4 to suit doors up to 1100mm
Finishes; silver (ses), stainless steel (sss)
Marking: C8 with roundel
Page 22
Advisory:
Closers are always to be fixed to the inside (unprotected) face of door leaf.
Use on doorsets that are likely to be otherwise
wedged open e.g. intercommunicating doors in
frequent use. Needs wired into fire alarm system
and the Fire Engineer should be advised.
C9 DOOR CLOSER
Cam Action electro-magnetic hold open slide arm door closer for door mounting push side of
door
&DPDFWLRQGRRUFORVHUZLWKIXOOFRYHUHOHFWURPDJQHWLFKROGRSHQVOLGHFKDQQHODQGFRQFHDOHGÀ[LQJV
Standards: &(PDUNHGWR(1&HUWLÀUHDSSURYHGIRUWLPEHUÀUHGRRUVKRXUVDQGPHWDOÀUHGRRUV
hours).
Size: power adjustable size EN 2-4 to suit doors up to 1100mm
Finishes; silver (ses), stainless steel (sss)
Marking: C9 with roundel
Advisory:
Closers are always to be fixed to the inside (unprotected) face of door leaf.
Use on doorsets that are likely to be otherwise
wedged open e.g. intercommunicating doors in
frequent use. Needs wired into fire alarm system
and the Fire Engineer should be advised.
Page 23
C10 DOOR CLOSER
Cam Action slide arm door closer for door mounting pull side of door
&DPDFWLRQEDFNFKHFNDQGGHOD\HGDFWLRQGRRUFORVHUZLWKIXOOFRYHUFRQFHDOHGÀ[LQJVDQGFXVKLRQHGOLPLW
stay
Standards: &(PDUNHGWR(1&HUWLÀUHDSSURYHGIRUWLPEHUÀUHGRRUVKRXUVDQGPHWDOÀUHGRRUV
hours).
Size: power adjustable size EN 2-5 to suit doors up to 1250mm
Finishes; silver (ses), stainless steel (sss)
Marking: C10 with roundel
Page 24
Advisory:
Closers are always to be fixed to the inside (unprotected) face of door leaf.
C11 DOOR CLOSER
Cam Action slide arm door closer for door mounting push side of door
&DPDFWLRQEDFNFKHFNDQGGHOD\HGDFWLRQGRRUFORVHUZLWKIXOOFRYHUFRQFHDOHGÀ[LQJVDQGFXVKLRQHGOLPLW
stay
Standards: &(PDUNHGWR(1&HUWLÀUHDSSURYHGIRUWLPEHUÀUHGRRUVKRXUVDQGPHWDOÀUHGRRUV
hours).
Size: power adjustable size EN 2-5 to suit doors up to 1250mm
Finishes; silver (ses), stainless steel (sss)
Marking: C11 with roundel
Advisory:
Closers are always to be fixed to the inside (unprotected) face of door leaf.
Page 25
C12 DOOR CLOSER
Cam Action slide arm door closer for door mounting pull side of door
&DPDFWLRQEDFNFKHFNDQGGHOD\HGDFWLRQGRRUFORVHUZLWKIXOOFRYHUFRQFHDOHGÀ[LQJVDQGFXVKLRQHGOLPLW
stay
Standards: &(PDUNHGWR(1&HUWLÀUHDSSURYHGIRUWLPEHUÀUHGRRUVKRXUVDQGPHWDOÀUHGRRUV
hours).
Size: power adjustable size EN 5-7 to suit doors up to 1400mm
Finishes; silver (ses), stainless steel (sss)
Marking: C12 with roundel
Page 26
Advisory:
Closers are always to be fixed to the inside (unprotected) face of door leaf.
C13 DOOR CLOSER
Cam Action slide arm door closer for door mounting push side of door
&DPDFWLRQEDFNFKHFNDQGGHOD\HGDFWLRQGRRUFORVHUZLWKIXOOFRYHUFRQFHDOHGÀ[LQJVDQGFXVKLRQHGOLPLW
stay
Standards: &(PDUNHGWR(1&HUWLÀUHDSSURYHGIRUWLPEHUÀUHGRRUVKRXUVDQGPHWDOÀUHGRRUV
hours).
Size: power adjustable size EN 5-7 to suit doors up to 1400mm
Finishes; silver (ses), stainless steel (sss)
Marking: C13 with roundel
Advisory:
Closers are always to be fixed to the inside (unprotected) face of door leaf.
Page 27
C14 DOOR CLOSER
Tandem mounted door closers for door mounting pull/push side of door
Tandem mounted backcheck door closers with mounting plate and tandem spindle connection.
Standards: &(PDUNHGWR(1&HUWLÀUHDSSURYHGIRUWLPEHUÀUHGRRUVKRXUVDQGPHWDOÀUHGRRUV
hours).
Size: SRZHUDGMXVWDEOHVL]H(1WRVXLWGRRUVXSWRPP
Finishes; silver
Marking: C14 with roundel
Advisory:
Closers are always fixed to the inside (un-protected / fire protected) face of door leaf, fitted
transom to push side of door – consult supplier’
Auxiliary brackets for restricted soffit conditions
may be required - consult with supplier.
Page 28
Lock Cases
Part No. L01 L/R
Mortise latch.
Latch bolt operated by lever handle from inside or outside.
Size:
)DFHSODWHPP[PPUDGLXVHQGPPEDFNVHW
Material:
Case: Heavy duty mild steel
)DFHSODWHVWDLQOHVVVWHHO
6WULNHSODWHVWDLQOHVVVWHHO
Finish:
Case: Galvanised or Hammerite
Faceplate: Satin brushed
Strikeplate: Satin brushed
Standards:
DIN 18 250 and 180 251
0RGXODUORFNUDQJHWHVWHGWR(1DQGHVFDSHIXQFWLRQ
(1&(PDUNHG)LUHWHVWHG(1
6SHFLÀFDWLRQ
Latch case body to be enclosed.
Solid follower to accept 9mm sq. bar spindle.
To be operated by F01 or F022 furniture sets and F13 or F44
for security access systems.
Marking: TfL-L01
0XVWEHXVHGLQFRQMXQFWLRQZLWK0/66.VWDLQOHVVVWHHOER[
VWULNHU
,/,QWXPHVFHQWSDUWORFNSURWHFWLRQSDFNDYDLODEOH
ARROW INDICATES DIRECTION OF
TRAVEL OR ESCAPE
',1/HIWSDQLFRSHQLQ
',15LJKWSDQLFRSHQLQ
',15LJKWSDQLFRSHQRXW
',1/HIWSDQLFRSHQRXW
Advisory:
Use in intercommunicating office doors where no
security is required.
Requires F01 or F22 lever/lever furniture - F13 or
F44 for security access systems.
F14 or F15 for drivers ‘J’ key.
Page 29
Lock Cases
Part No. L02 L/R
Mortise sash lock with panic escape function E.
Escape: Escape from inside at all times by depressing lever handle.
Access: Access from outside only available by inserting key and turning to withdraw deadbolt on
turns one and two with the latch bolt on the third
Security: Re-entry after escape only possible with key.
Size:
)DFHSODWHPP[PPUDGLXVHQGPPEDFNVHWFHQtres 72mm
Material:
Case: Heavy duty mild steel
)DFHSODWHVWDLQOHVVVWHHO
Finish:
Case: Galvanised
Face plate: Satin brushed
Standards:
DIN 18 250 and 180 251
0RGXODUORFNUDQJHWHVWHGWR(1DQGHVFDSHIXQFWLRQ(1&(PDUNHG)LUHWHVWHG(1
6SHFLÀFDWLRQ
Latch case body to be enclosed.
Solid follower to accept 9mm sq. bar spindle.
To be operated by F13 and F44 furniture sets.
Marking: TfL-L02 on face plate
0XVWEHXVHGLQFRQMXQFWLRQZLWK0/66.VWDLQOHVVVWHHOER[
VWULNHU
,/,QWXPHVFHQWSDUWORFNSURWHFWLRQSDFNDYDLODEOH
ARROW INDICATES DIRECTION OF
TRAVEL OR ESCAPE
Page 30
',1/HIWSDQLFRSHQLQ
',15LJKWSDQLFRSHQLQ
',15LJKWSDQLFRSHQRXW
',1/HIWSDQLFRSHQRXW
Advisory:
Use in equipment room, store room and public
facing doors.
Requires F13/1/2/3/4 or F44/1/2/3/4 pull/lever
handle furniture.
Requires correct MLSSK 44/55 strike.
Lock Cases
Part No. L03 L/R
0RUWLVHVDVKORFNZLWKSDQLFHVFDSHIXQFWLRQ%RSHQRXW
Escape: Escape from inside at all times by depressing lever handle.
Access: Access from outside only available by inserting key and turning to withdraw deadbolt on
turn one and turn two activates the outside lever. Free access when unlocked.
Security: Re-entry after escape only possible with key turned to activate lever handle.
Size:
)DFHSODWHPP[PPUDGLXVHQGPPEDFNVHW
centres 72mm
Material:
Case: Heavy duty mild steel
)DFHSODWHVWDLQOHVVVWHHO
6WULNHSODWHVWDLQOHVVVWHHO
Finish:
Case: Galvanised or Hammerite
Face plate: Satin brushed
Strike plate: Satin brushed
Standards:
DIN 18 250 and 180 251
0RGXODUORFNUDQJHWHVWHGWR(1DQGHVFDSHIXQFWLRQ
(1&(PDUNHG)LUHWHVWHG(1
6SHFLÀFDWLRQ
Latch case body to be enclosed.
Euro cylinder cut-out.
Split follower to accept 9mm sq. bar spindle.
To be operated by F04 and F25 furniture sets.
Marking: TfL-L03 on face plate
0XVWEHXVHGLQFRQMXQFWLRQZLWK0/66.VWDLQOHVVVWHHOER[
VWULNHU
,/,QWXPHVFHQWSDUWORFNSURWHFWLRQSDFNDYDLODEOH
ARROW INDICATES DIRECTION OF
TRAVEL OR ESCAPE
',15LJKWSDQLFRSHQRXW
',1/HIWSDQLFRSHQRXW
Advisory:
Use in internal staff accommodation.
Requires F04 or F25 lever/lever furniture.
Requires correct MLSSK 44/55 strike.
Page 31
Lock Cases
Part No. L04 L/R
0RUWLVHVDVKORFNZLWKSDQLFHVFDSHIXQFWLRQ%RSHQLQ
Escape: Escape from inside at all times by depressing lever handle.
Access: Access from outside only available by inserting key and turning to withdraw deadbolt
on turn one and turn two activates the outside lever. Free access when unlocked.
Security: Re-entry after escape only possible with key turned to activate lever handle.
Size:
)DFHSODWHPP[PPUDGLXVHQGPPEDFNVHW
centres 72mm
Material:
Case: Heavy duty mild steel
)DFHSODWHVWDLQOHVVVWHHO
6WULNHSODWHVWDLQOHVVVWHHO
Finish:
Case: Galvanised
Face plate: Satin brushed
Strike plate: Satin brushed
Standards:
DIN 18 250 and 180 251
0RGXODUORFNUDQJHWHVWHGWR(1DQGHVFDSHIXQFWLRQ(1&(PDUNHG)LUHWHVWHG(1
6SHFLÀFDWLRQ
Latch case body to be enclosed.
Euro cylinder cut-out.
Split follower to accept 9mm sq. bar split spindle.
To be operated by F04 and F25 furniture sets.
Marking: TfL-L04 on face plate
0XVWEHXVHGLQFRQMXQFWLRQZLWK0/66.VWDLQOHVVVWHHO
ER[VWULNHU
,/,QWXPHVFHQWSDUWORFNSURWHFWLRQSDFNDYDLODEOH
ARROW INDICATES DIRECTION OF
TRAVEL OR ESCAPE
',1/HIWSDQLFRSHQLQ
',15LJKWSDQLFRSHQLQ
Advisory:
Use in internal staff accommodation doors
Requires F04 or F25 lever/lever furniture.
Requires correct MLSSK 44/55 strike.
Page 32
Lock Cases
Part No. L12 L/R
Mortise sash lock.
Escape: Only possible when the deadbolt is not engaged, latch bolt operated by depressing
lever handle.
Access: Access from outside only available by inserting and turning key to unlock the deadbolt
Free access when unlocked..
Security: Re-entry after escape possible by depressing lever handle
Size:
PP[PPUDGLXVHQGPPEDFNVHWFHQWUHVPP
Material:
Case: Heavy duty mild steel
)DFHSODWHVWDLQOHVVVWHHO
6WULNHSODWHVWDLQOHVVVWHHO
Finish:
Case: Galvanised
Face plate: Satin brushed
Strike plate: Satin brushed
Standards:
DIN 18 250 and 180 251
0RGXODUORFNUDQJHWHVWHGWR(1&(PDUNHG)LUH
WHVWHG(1
6SHFLÀFDWLRQ
Latch case body to be enclosed.
Euro cylinder cut-out.
Solid follower to accept 9mm sq. bar spindle.
To be operated by F04X and F25X furniture sets.
Marking: TfL-L12 on face plate
0XVWEHXVHGLQFRQMXQFWLRQZLWK0/66.VWDLQOHVVVWHHOER[
VWULNHU
,/,QWXPHVFHQWSDUWORFNSURWHFWLRQSDFNDYDLODEOH
ARROW INDICATES DIRECTION OF
TRAVEL OR ESCAPE
',1/HIWSDQLFRSHQLQ
',15LJKWSDQLFRSHQLQ
',15LJKWSDQLFRSHQRXW
',1/HIWSDQLFRSHQRXW
Advisory:
Use in cupboard, store room or office doors where
panic escape is not required.
Requires F04x or F25x lever/lever handle.
Requires correct MLSSK 44/55 strike.
Page 33
Lock Cases
Part No. L13 L/R
Mortise bathroom lock.
Escape: Only possible when the deadbolt is not engaged, latch bolt operated by depressing
lever handle.
Access: Access from outside only available by depressing lever handle,deadbolt can be withdrawn in an emergency by turning external release.
Security: None.
Size:
PP[PPUDGLXVHQGPPEDFNVHWFHQWUHVPP
Material:
Case: Heavy duty mild steel
)DFHSODWHVWDLQOHVVVWHHO
6WULNHSODWHVWDLQOHVVVWHHO
Finish:
Case: Galvanised
Face plate: Satin brushed
Strike plate: Satin brushed
Standards:
DIN 18 250 and 180 251
0RGXODUORFNUDQJHWHVWHGWR(1DQGHVFDSHIXQFWLRQ
(1&(PDUNHG)LUHWHVWHG(1
6SHFLÀFDWLRQ
Latch case body to be enclosed.
No cylinder cut-out.
Solid follower to accept 9mm sq. bar spindle.
To be operated by F04WC and F25WC furniture sets.
Marking: TfL-L13 on face plate
0XVWEHXVHGLQFRQMXQFWLRQZLWK0/66.VWDLQOHVVVWHHOER[
VWULNHU
,/,QWXPHVFHQWSDUWORFNSURWHFWLRQSDFNDYDLODEOH
ARROW INDICATES DIRECTION OF
TRAVEL OR ESCAPE
',1/HIWSDQLFRSHQLQ
',15LJKWSDQLFRSHQLQ
',15LJKWSDQLFRSHQRXW
',1/HIWSDQLFRSHQRXW
Advisory:
Use in staff and public WC’s.
Requires F04WC or F25WC lever/lever handle.
Can be used in conjunction with L17 mortise dead
lock to allow isolation of toilets for maintenance.
Requires correct MLSSK 44/55 strike.
Page 34
Lock Cases
Part No. L14 L/R
0RUWLVHVDVKORFNZLWKDXWRÀUHSDQLFHVFDSHIXQFWLRQ(
Escape: Escape from inside at all times by depressing lever handle.
Access: Access from outside only available by inserting key and turning to withdraw deadbolt
and latchbolt.
6HFXULW\ 2QFORVLQJWKHGRRUWKHODWFKEROWDXWRÀUHVWKHVHFRQGDU\ODWFKEROWLQWRGHDGEROW
function, re-entry only possible by inserting and turning key from outside. Size:
PP[PPUDGLXVHQGPPEDFNVHWFHQWUHVPP
Material:
)DFHSODWHVWDLQOHVVVWHHO
Case: Heavy duty mils steel
Finish:
Case: Galvanised
Face plate: Satin brushed
Strike plate: Satin brushed
Standards:
DIN 18 250 and 180 251
0RGXODUORFNUDQJHWHVWHGWR(1DQGHVFDSHIXQFWLRQ(1&(PDUNHG)LUHWHVWHG(1
6SHFLÀFDWLRQ
Latch case body to be enclosed.
Euro cylinder cut-out.
Solid follower to accept 9mm sq. bar spindle.
To be operated by F13 and F44 furniture sets.
Marking: TfL-L14 on face plate
0XVWEHXVHGLQFRQMXQFWLRQZLWK0/66.
VWDLQOHVVVWHHOER[VWULNHU
,/,QWXPHVFHQWSDUWORFNSURWHFWLRQSDFNDYDLODEOH
ARROW INDICATES DIRECTION OF
TRAVEL OR ESCAPE
',1/HIWSDQLFRSHQLQ
',15LJKWSDQLFRSHQLQ
',15LJKWSDQLFRSHQRXW
',1/HIWSDQLFRSHQRXW
Advisory:
Use in access doors to staff accommodation,
equipment and secure rooms e.g.: lobby, fire exit
or where additional security is required
Requires F13/1/2/3/4 or F44/1/2/3/4 lever pull
furniture.
Requires correct MLSSK 44/55 strike.
Page 35
Lockcases
Part No. L16
Mortise auto deadlatch
Escape:
Escape from inside at all times by depressing lever handle.
Access:
Access from outside only available by inserting key and turning to withdraw dead
bolt and latchbolt.
Security:
On closing the door the deadlatch/latchbolt operates. Re-entry only possible by
inserting and turning key from outside.
Size:
PP[PPUDGLXVHQGPPEDFNVHWFHQWUHVPP
Material:
)DFHSODWHVWDLQOHVVVWHHO
Case: Heavy duty mild steel
Finish:
Case: Galvanised
Face plate: Satin brushed
Strike plate: Satin brushed
Standards:
DIN 18 250 and 180 251
0RGXODUORFNUDQJHWHVWHGWR(1DQGHVFDSHIXQFWLRQ(1&(PDUNHG)LUHWHVWHG(1
6SHFLÀFDWLRQ
Latch case body to be enclosed.
Euro cylinder cut-out.
Solid follower to accept 9mm sq. bar spindle.
To be operated by F13 and F44 furniture sets.
0DUNLQJ7I//RQIDFHSODWH
7REHXVHGLQFRQMXQFWLRQZLWK('6VWDLQOHVVVWHHODQWLWKUXVWVQLESUHYHQWVODWFKEROWPDQLSXODWLRQ
,/,QWXPHVFHQWSDUWORFNSURWHFWLRQSDFNDYDLODEOH
ARROW INDICATES DIRECTION OF
TRAVEL OR ESCAPE
',1/HIWSDQLFRSHQLQ
',15LJKWSDQLFRSHQLQ
',15LJKWSDQLFRSHQRXW
',1/HIWSDQLFRSHQRXW
Advisory:
Use in office door where access control is required
Requires EDS1 (2013) electronic release,
F13/1/2/3/4, F44/1/2/3 or F14 door furniture.
Requires correct MLSSK 44/55 strike.
Page 36
Lockcases
Part No. L17
Mortise dead lock
Escape:
Only possible when the deadbolt is not engaged. Deadbolt operated by turning the
key to unlock.
Access:
Access from outside only available by inserting the key and turning to withdraw the
deadbolt.
Security:
The deadbolt functions only through the use of the key.
Size:
PP[PPUDGLXVHQGPPEDFNVHW
Material:
)DFHSODWHVWDLQOHVVVWHHO
Case: Heavy duty mild steel
6WULNHSODWH6VWDLQOHVVVWHHO
Finish:
Case: Galvanised
Face plate: Satin brushed
Strike plate: Satin brushed
Standards:
DIN 18 250 and 180 251
0RGXODUORFNUDQJHWHVWHGWR(1DQGHVFDSHIXQFWLRQ
(1&(PDUNHG)LUHWHVWHG(1
6SHFLÀFDWLRQ
Latch case to be enclosed.
Euro cylinder cut-out
Marking: TfL-L17 on face plate
IL1 intumescent 3 part lock protection pack available
Advisory:
Use in cupboard doors or doors where panic escape is not required.
Use with F05 A/B/C/D escutcheons.
Can be used in conjunction with L13 mortise bathroom lock to allow isolation of toilets for maintenance.
Requires correct MLSSK strike - consult supplier.
Page 37
Lockcases
Part No. L18 L/R
Mortise bathroom lock
Escape:
Access:
Security:
Latch and deadbolt operated by depressing lever handle.
Access from outside only available by depressing lever handle, deadbolt can be
withdrawn in an emergency by turning external release.
None
Size:
)DFHSODWH[EDFNVHWFHQWUHV
Material:
Face plate Stainless steel
Case Heavy duty mild steel
Finish:
Face plate Satin brushed
Case: Mild steel Hammerite
Standards:
BS 8300 Document M
6SHFLÀFDWLRQ
Latch case body to be enclosed
No cylinder cut-out
)L[LQJV6ROLGIROORZHUWRDFFHSWVSLQGOH
ARROW INDICATES DIRECTION OF
TRAVEL OR ESCAPE
',1/HIWSDQLFRSHQLQ
',15LJKWSDQLFRSHQLQ
',15LJKWSDQLFRSHQRXW
',1/HIWSDQLFRSHQRXW
Advisory:
Use in staff and public WC’s.
Requires WC1 lever/lever handle.
Requires correct MLSSK 44/55 strike.
Page 38
Lock Cases
Part No. L19 L/R
Mortise sash lock with deadlocking latch panic escape function E
Escape:
Access:
Security:
Escape from inside at all times by depressing lever handle.
Access from outside only available by inserting key and turning to withdraw deadbolt, when fully key secured. Normal action is latch turn to open, when manned.
re-entry after escape only possible with key.
Size:
)DFHSODWHPP[PPUDGLXVIRUHQGPPEDFNVHW
centres 72mm.
Material:
Face plate Stainless steel
Case Heavy duty mild steel
Finish:
Face plate Satin brushed
Case: Galvanised
Standards:
DN 18250 and 180251
6SHFLÀFDWLRQ
Modular lock range CE marked and tested to EN 12209 and
panic escape EN 179. )LUHWHVWHG(1
Compliant to BS 8300 Document M
ARROW INDICATES DIRECTION OF
TRAVEL OR ESCAPE
',1/HIWSDQLFRSHQLQ
',15LJKWSDQLFRSHQLQ
',15LJKWSDQLFRSHQRXW
',1/HIWSDQLFRSHQRXW
Advisory:
Use on public facing doors to staff accommodation, where additional security is required.
Dead latch prevents unlawful manipulation
and deadbolt gives additional ‘out of office’
security.
Requires EDS1 (2013) electric strike, deadlock
version or MLSSK manual strike - consult supplier.
Page 39
Mortice strike plate
Part No. MLSSK 44/54
Size:
[
Material:
VWDLQOHVVVWHHO
Fixings:
8VHVXLWDEOH7RU[KHDGVFUHZV
Finish:
Satin brushed
6SHFLÀFDWLRQ
Anti-rattle adjustment available on 54mm size.
Advisory:
Powder coated antique bronze for heritage doors
opening outwards in public areas only.
Use with all mortice lockcases.
Page 40
Electric strikes
3DUW1R('6
High Security
Escape: By using internal lever handle
Access: Access from outside only available by inserting key and turning to withdraw the latchbolt.
Security: Self locking. For use in areas with electronic access systems.
Size:
6WDLQOHVVSODWH[
Material:
Stainless steel face plate and steel and cast release
Fixings:
[QR[PPWLPEHUVFUHZV
('6%3EULGJLQJSODWHVHWVDYDLODEOHIRUVWHHO
door sets
Finish:
Satin Stainless Steel
Standards:
)LUHUDWHGGRRUVWULNHDYDLODEOHZLWKDEUHDNRSHQSUHVVXUH
RI1HZWRQ·V1ZLWKDGMXVWDEOHODWFKVOLGHWRHQVXUH
WKHGRRUFDQFORVHWLJKWO\)DLOORFNHGVWULNHVRSHQZKHQWKH
FXUUHQWLVDSSOLHGDQGORFNDXWRPDWLFDOO\ZKHQWKHSRZHULV
UHPRYHG
6WULNHVDUHRSWLRQDOO\DYDLODEOHZLWKDEXLOWLQPLFURVZLWFKWR
PRQLWRUODWFKEROWHQJDJHPHQWDGMXVWDEOHSRZHUFRQVXPSWLRQYROWV²YROWVJLYLQJGXW\UDWLR
6SHFLÀFDWLRQ
7RVXLWIUDPHVDQGUHSODFHDSSURYHGVWULNHV²0/66.IRU
doors requiring access control and door entry systems e.g.
PDQQHG&RQWURO5RRPVDQGRIÀFHV
Advisory:
Use with L02 or L16 lockcases for latch only,
deadlocking available using L02 or L19 lockcases
when office is left unmanned.
Consult supplier for alternative models.
Page 41
Digital access key pad
Part No. DKP
6L]HZPP[KPP
)L[LQJVXVHVXLWDEOH[QR[PPWRU[KHDGVFUHZV
Finish: satin brushed
6SHFLÀFDWLRQ
12 SWG stainless steel vandal resistant key pad,.
7RÁXVKPRXQWRUGHU3DUW1R'.3RQO\
)XOÀOOLQJUHTXLUHPHQWVDQGGXWLHVUHTXLUHGXQGHUWKH(TXDOLW\$FWE\VDWLVI\LQJWKHUHFRPPHQGDWLRQVRI%6
8300 and Approved Document M.
Advisory:
Used for access to ‘back of house’ areas by staff
and others where non key access is required, in
conjunction with EDS1 (2013) electric strike.
Electrical Engineer of requirement and take advice of lock release requirement.
Available flush fitted or with Stainless Surface
Housings, add SSH, consult supplier
Page 42
Speech panels with call button
Part No. ASP/ASVP
Size:
[
Material:
VWDLQOHVVVWHHO
Fixings:
8VHVXLWDEOH[1RPP7RU[KHDGVFUHZV
Finish:
Satin brushed
6SHFLÀFDWLRQ
12swg stainless steel vandal-resistant audio, surface mount,
LQFOXGHVLOOXPLQDWHGWDFWLOH¶&$//·EXWWRQ¶63($.12:·/('
DQG¶'22523(1·/(')XOÀOOLQJUHTXLUHPHQWVDQGGXWLHV
required under the Equality Act by satisfying the recommendations of BS 8300 and Approved Document M.
Part No. VRVDDA1 video entry panel
Part No. ASP audio entry panel
Part No. ASVP - audio
video entry panel
Advisory:
Use adjacent to Control Room doors in conjunction with EDS 1 (2013) electric strike. Advise HF
Engineer and Electrical Engineer of requirement
and take advice of speech transfer/lock release
requirement.
Available flush fitted or with Stainless Surface
Housings, add SSH, consult supplier
Page 43
Speech panels with call button
Part No. AVKPSP/AVACSP
Size:
$9.363[$9$&63[
Material:
VWDLQOHVVVWHHO
Fixings:
8VHVXLWDEOH[1RPP7RU[KHDGVFUHZV
Finish:
Satin brushed
Part No. AVKPSP - audio
video entry panel with
keypad
6SHFLÀFDWLRQ
12swg stainless steel vandal-resistant audio, surface mount,
LQFOXGHVLOOXPLQDWHGWDFWLOH¶&$//·EXWWRQ¶63($.12:·/('
DQG¶'22523(1·/('IXOÀOOLQJUHTXLUHPHQWVDQGGXWLHV
required under the Equality Act by satisfying the recommendations of BS 8300 and Approved Document M.
Part No. AVACSP - audio
video entry panel with
access control
Advisory:
Use adjacent to Control Room doors in conjunction with
EDS 1 (2013) electric strike. Advise HF Engineer and
Electrical Engineer of requirement and take advice of
speech transfer/lock release requirement.
Available flush fitted or with Stainless Surface
Housings, add SSH, consult supplier
Page 44
Panic Bolts
Part No. F06
Mortise panic actuator
&ODVVLÀFDWLRQ
3 7 B 1 3 2 2 A A
6SHFLÀFDWLRQ
6XUIDFHPRXQWHGSDQLFODWFKDFWXDWRUZLWKHXURSURÀOHPRUtise nightlatch to BSEN 1125
C.E.N Compliant and C.E. marked
Self handing
)L[LQJNLWVIRUERWKWLPEHUDQGVWHHOGRRUVHWVDYDLODEOH
)LUHGRRUWHVWHG0XVWEHXVHGZLWK/8,/,LQWXPHVFHQWSDUW
lock protection pack)
Finish: satin stainless steel
Material: chrome passivated and stainless steel coat effect
ARROW INDICATES DIRECTION OF
TRAVEL OR ESCAPE
',15LJKWSDQLFRSHQRXW
',1/HIWSDQLFRSHQRXW
Advisory:
Use on single escape door open out or active leaf
of double door set
External access by external single cylinder and
pull or, where free access is required on internal
doors, by external access device F08
Page 45
Panic Bolts
Part No. F07
Single panic bolt
&ODVVLÀFDWLRQ
3 7 B 1 3 2 2 A A
6SHFLÀFDWLRQ
6XUIDFHPRXQWHGVLQJOHSDQLFEROWZLWKDXWRÀUHWRSWULSFDWFK
to BSEN 1125
C.E.N Compliant and C.E. marked
Self handing
)L[LQJNLWVIRUERWKWLPEHUDQGVWHHOGRRUVHWVDYDLODEOH
)LUHWHVWHGWR(1
Finish: satin stainless steel
Material: chromium passivated and stainless steel coat effect
ARROW INDICATES DIRECTION OF
TRAVEL OR ESCAPE
',15LJKWSDQLFRSHQRXW
',1/HIWSDQLFRSHQRXW
Advisory:
Use on passive leaf of double leaf fire exit in conjunction with F06.
Page 46
Emergency Exit Device
Part No. EED 1
Surface mounted, single-point emergency escape device to BS EN 179, CE marked
&ODVVLÀFDWLRQ
3 7 B 1 4 5 1 A B
6SHFLÀFDWLRQ
For use on a single leaf or the active leaf of double doors
ZKHUHDVLQJOHSDQLFHVFDSHOHDIRQO\LVUHTXLUHG.HHSVDQG
À[LQJVDUHDYDLODEOHIRUWLPEHURUVWHHOGRRUV
Escape:
Escape from inside at all times by depressing lever handle.
Access:
Optional access from outside available by inserting key and
turning to withdraw deadbolt.
Security:
Re-secures each time upon door closure.
Handing:
Handing and opening direction required.
ARROW INDICATES DIRECTION OF
TRAVEL OR ESCAPE
',1/HIWSDQLFRSHQLQ
',15LJKWSDQLFRSHQLQ
',15LJKWSDQLFRSHQRXW
',1/HIWSDQLFRSHQRXW
Standard keeps
2XWZDUGRSHQLQJ
Advisory:
Use on non-public escape doors and gates with
cylinder or J key.
Page 47
Panic Exit Latch
Part No. PEL 1 L/R
Surface mounted panic latch actuator with 9mm follower operating a mortice latch, accredited to
BS EN 1125, CE marked
&ODVVLÀFDWLRQ
3 7 0 1 3 2 1 A A
6SHFLÀFDWLRQ
For use on a single leaf or the active leaf of double doors
where a single panic escape leaf only is required. Supplied
FRPSOHWHZLWKSDQLFH[LWODWFKPPVSLQGOHÀ[LQJVDQGNHHS
IRUDWLPEHUGRRUÀ[LQJVIRUVWHHOGRRUVDUHDYDLODEOH
Escape:
Escape from inside at all times by depressing panic bar.
Access:
Optional access from outside available by inserting key and
turning to withdraw latch.
Handing:
Handing is required
Security:
Re-latches automatically upon door closure.
ARROW INDICATES DIRECTION OF
TRAVEL OR ESCAPE
',15LJKWSDQLFRSHQRXW
',1/HIWSDQLFRSHQRXW
Advisory:
Use in conjunction with L01 and L16 lockcases
Page 48
Panic Exit System
Part No. PES 2 L/R
Surface mounted, 2-point panic escape device to BS EN 1125, CE marked
&ODVVLÀFDWLRQ
3 7 B 1 3 2 1 A A
6SHFLÀFDWLRQ
For use on a single leaf or both the active and inactive leaf of
GRXEOHGRRUVZLWKSODLQPHHWLQJVWLOHV6XSSOLHGZLWKÀLQJV
DQGNHHSVIRUDWLPEHUGRRUÀ[LQJVIRUVWHHOGRRUVDUHDYDLOable).
Escape:
Escape from inside at all times by depressing panic bar.
Access:
Optional access from outside available by inserting key and
turning to withdraw deadbolt then to turn lever hand to release the bolts.
Security:
Re-secures each time upon door closure.
Standard keeps
Top keep & strike
'XVWIUHHÁRRUNHHS
ARROW INDICATES DIRECTION OF
TRAVEL OR ESCAPE
',15LJKWSDQLFRSHQRXW
',1/HIWSDQLFRSHQRXW
Advisory:
Use on final exit requiring high security and leading to a public space.. Can be used on the passive
leaf of double leaf fire exit in conjunction with
PEL 1
Page 49
Secure Suit Deadlock
Part No. SSD 3
Surface mounted, encased 3-point deadlocking device to BS EN 179, CE marked
6SHFLÀFDWLRQ
.H\UHOHDVHGHDGORFNDQGOHYHUKDQGOHHQWU\ZLWKDQLQWHUQDO
OHYHUKDQGOHWRSURYLGHDRQHKDQGHGPHDQVRIH[LWIRUVLQJOH
OHDIGRRUV6XSSOLHGZLWKÀ[LQJVDQGNHHSVIRUDWLPEHUGRRU
À[LQJVIRUVWHHOGRRUVDUHDYDLODEOH
Escape:
Escape from inside at all times by depressing lever handle.
Access:
By inserting a key and turning to unlock then turning the lever
handle to release the multiple bolts.
Security:
Re-secures automatically each time the door reaches it’s
closed position.
Handing:
Handing and opening direction is required (see chart below)
Standard keeps
Top keep & strike
ARROW INDICATES DIRECTION OF
TRAVEL OR ESCAPE
',1/HIWSDQLFRSHQLQ
',15LJKWSDQLFRSHQLQ
',15LJKWSDQLFRSHQRXW
',1/HIWSDQLFRSHQRXW
Centre keep
Protected external key cylinder and handle entry
'XVWIUHHÁRRUNHHS
Page 50
Collapsible gate device
Part No. CGD 1A L/R
6SHFLÀFDWLRQ
$OOVWHHOFRQVWUXFWLRQÀWWHGWRPDLQHQWUDQFHH[WHUQDOJDWHVVOLGHWULJJHUVHWIRUÀQDODXWRORFNLQJJDWH
Escape:
Single handed emergency escape inside by depressing lever handle (red).
Access:
2SWLRQDODFHVVIURPRXWVLGHRIDXWRÀUHDFWLYHOHDIXVLQJOHR
Security:
7ZRSRLQWPDQXDOORFNLQJRQVHFRQGDU\JDWH$XWRÀULQJWKUHHSRLQWORFNLQJRQÀQDOH[LWHQWUDQFHJDWH
Optional: Single and double gates can use combination of either option
Finish: dark grey hammerite lockcase and saddles, sss bars and bolts red handles.
Handing:
Handing and opening direction is required (see chart below)
Size:[[
Material:0LOGVWHHOZLWKVWDLQOHVVVWHHOURGVEDUV
Fixings:/RFNFDVH0KH[6DGGOHV0KH[
Right hand
inside
Left hand
inside
Advisory:
Optional external key and LEO 1/2/3/4
Internal handle sprung hinged door box
shrouds and cover plates available for standard additonal security located in stainless
housings. When open secured with budget /
key suited locks designed installed, consult
supplier
Page 51
Collapsible gate device
Part No. CGD 1B L/R
6SHFLÀFDWLRQ
$OOVWHHOFRQVWUXFWLRQÀWWHGWRPDLQHQWUDQFHH[WHUQDOJDWHVVOLGHWULJJHUVHWIRUÀQDODXWRORFNLQJJDWH
Escape:
Single handed emergency escape inside by depressing lever handle (red).
Access:
2SWLRQDODFHVVIURPRXWVLGHRIDXWRÀUHDFWLYHOHDIXVLQJOHR
Security:
7ZRSRLQWPDQXDOORFNLQJRQVHFRQGDU\JDWH$XWRÀULQJWKUHHSRLQWORFNLQJRQÀQDOH[LWHQWUDQFHJDWH
Optional: Single and double gates can use combination of either option
Finish: dark grey hammerite lockcase and saddles, sss bars and bolts red handles.
Handing:
Handing and opening direction is required (see chart below)
6L]H[[
0DWHULDO0LOGVWHHOZLWKVWDLQOHVVVWHHOURGVEDUV
)L[LQJV/RFNFDVH0KH[6DGGOHV0KH[
Right hand
inside
Left hand
inside
Advisory:
Optional external key and LEO 1/2/3/4
Internal handle sprung hinged door box
shrouds and cover plates available for standard additonal security located in stainless
housings. When open secured with budget /
key suited locks designed installed, consult
supplier
Page 52
Collapsible Gate Device
Part No. CGD 2 L/R
Deadlocking twin-hook lock for securing collapsible sliding gates
Size:
)DFHSODWH[[
/RFNERG\[[
%R[NHHS[[
Material:
Case: Heavy duty mild steel
Face plate: Heavy duty mild steel
%R[NHHS+HDY\GXW\PLOGVWHHO
Finish:
Case: Zinc passivated
Face plate: Zinc passivated
%R[NHHS=LQFSDVVLYDWHG
Fixings:
Lock body: M8
Hook lock body to be enclosed.
6SHFLÀFDWLRQ
$OOVWHHOFRQVWUXFWLRQIRUUHWURÀWWLQJWRFROODSVLEOHJDWHV
handles can be provided on one or both sides providing an
HPHUJHQF\HVFDSH6XSSOLHGZLWKÀ[LQJVDQGER[NHHS
Escape:
Single handed emergency escape from inside by depressing
emergency lever handle (green).
Access:
Optional, access from outside is available by inserting key
and turning to withdraw deadbolt then to turn lever handle to
release the bolts.
Security:
The twin-hook locks latch and deadlock automatically upon
gate closure.
2SWLRQDO
)RUJDWHVZKLFKGRQRWUHTXLUHDQHPHUJHQF\H[LWNH\F\OLQGHUVFDQEHÀWWHGRQRQHRUERWKVLGHVZLWKQDWXUDOÀQLVK
stainless steel handle(s), to provide key controlled operation.
Right hand
inside
Left hand
inside
Advisory:
Optional external key and lever handle entry.
Green lever handle for emergency release.
Page 53
Miscellaneous
Part No. G3/G4/G2A
Barrel bolt set.
6SHFLÀFDWLRQ
+HDY\GXW\PPEDUUHOEROWZLWKÁRRUVRFNHWDQGÁXVKGRRU
staple for open-in or open-out passive leaf of double door
set.
Finish: 0LOGVWHHO33&ÀQLVKRUEODFN+DPPHULWH
)L[LQJVWREHDSSURSULDWHWRWKHGRRUVHWFRQVWUXFWLRQ
Advisory:
Specify keeps as required from below
G3 Barrel bolt
G4 Dust excluding socket
G2A Flush door staple
Page 54
Miscellaneous
Part No. K4/K5
Kick plates
6SHFLÀFDWLRQ
.0DWHULDO
%6(1JUDGHVWDLQOHVVVWHHO[PPGRRU
ZLGWKOHVVVWRSV[PPWR%6VHFXUHE\7RU[KHDG
screws.
.0DWHULDO
5HDOEURQ]HPHWDODQWLTXHRQJXQPHWDO[PPGRRUZLGWK
OHVVVWRSV[PPWR%6VHFXUHE\7RU[KHDGVFUHZV
Page 55
Miscellaneous
Part No. F1/F2
Finger plates
6SHFLÀFDWLRQ
)VWDQGDUG
Material:
VWDLQOHVVVWHHO[[FRPSOHWHZLWKÀ[LQJVIRU
timber
)ODUJH
Material:
VWDLQOHVVVWHHO[[FRPSOHWHZLWKÀ[LQJVIRU
timber
Advisory:
Please specify when ordering:
316 stainless steel, radius corners, satin finish,
etc. Other sizes and finishes are available
Page 56
Miscellaneous
Part No. K1/K2/K3/K6
Door stops, coat hook and door selector
6SHFLÀFDWLRQ
.:DOOGRRUVWRS%6(1JUDGHVWDLQOHVVVWHHO
.)ORRUGRRUVWRS%6(1JUDGHVWDLQOHVVVWHHO
.'RRUPRXQWHGKDWDQGFRDWKRRN%6(1JUDGH
VWDLQOHVVVWHHO
.'RRUVHOHFWRUHQDEOHVDSDLURIVHOIFORVLQJGRRUVZLWKUHEDWHG
meeting stiles or overlapping astragal to close in the correct sequence
DXWRPDWLFDOO\QRPDWWHUZKLFKGRRULVRSHQHGÀUVW7HVWHGWR%6
(1%6(1JUDGHVWDLQOHVVVWHHO6XLWDEOHWLPber doors of any width up to 1220mm (4’0”) per door and all standard
thicknesses and rebate sizes.
K1 wall door stop
.ÁRRUGRRUVWRS
K3 hat and coat hook
K6 door selctor for double doors with rebated meeting stiles
Page 57
Key Cabinet and Boxes
6SHFLÀFDWLRQ
&$%
6L]HPP[PP[PP
Standard capacity 100. Other sizes available.
&$%
6L]HPP+[PP:[PP([FOXGLQJF\OLQGHUSURWUXVLRQ
.H\ER[ZLWKVLQJOHKRRNIRUUHVWULFWHGDFFHVVNH\NH\V
&$%
6L]HPP[PP[PP
%UHDNJODVVER[IRUHPHUJHQF\DFFHVV
CAB 2 single hook for restricted
access key
CAB 1 100 key capacity
CAB 3 break glass box for station
emergency keys
Advisory:
Key access can be under Site Master System,
keyed alike or differs.
Page 58
Typical Doorset Arrangements
SINGLE LEAF FD60 EQUIPMENT ROOM DOOR WITHOUT GLAZING APERTURE
Furniture • L02R mortise sash lock with panic function E deadbolt and latch or L14R mortise sash
lock autofire panic action deadbolt and latch
• F13/1/2/3/4 on pierced backplates or F44/1/2/3/4 on escutcheons and roses pull/lever
handles
• A1/SS/BGMA or A4/SS/BMA hinges
• C7 overhead door closer
• K4 or K5 kick plates
note wall finishes and architraves omitted for clarity
Furniture - refer to Approved Ironmongery
for the Railway Environment for specific door
requirements
Signs - follow the heirarchy laid down in the
LUL Signs Manual section 6.8
Page 59
Typical Doorset Arrangements
SINGLE LEAF FD60 EQUIPMENT ROOM DOOR WITH GLAZING APERTURE
Furniture • L02R mortise sash lock with panic function E deadbolt and latch or L14R
mortise sash lock autofire panic action deadbolt and latch
• F13/1/2/3/4 on pierced backplates or F44/1/2/3/4 on escutcheons and roses
pull/lever handles
• 1.5 pair A1/SS/BGMA or A4/SS/BMA hinges (for doors in excess of 910x21oo use 2
pairs)
note wall finishes and architraves omitted for clarity
Furniture - refer to Approved Ironmongery
for the Railway Environment for specific door
requirements
Signs - follow the heirarchy laid down in the
LUL Signs Manual section 6.8
Page 60
Typical Doorset Arrangements
DOUBLE LEAF FD60 EQUIPMENT ROOM DOOR WITHOUT GLAZING APERTURE
Furniture • L02R mortise sash lock with panic function E deadbolt and latch or L14R mortise sash
lock autofire panic action deadbolt and latch
• F13/1/2/3/4(D) on pierced backplates or F44/1/2/3/4(D) on escutcheons and roses pull/
lever handles
• 3 pair A1/SS/BMA or A4/SS/BMA hinges (for door in excess of 910x2100 use 4 pairs)
• 1 pair C7 overhead door closers
• 1 pair G3/G4/G2C barrel bolt sets
• K4 or K5 kick plates
note wall finishes and architraves omitted for clarity
Furniture - refer to Approved Ironmongery
for the Railway Environment for specific door
requirements
Signs - follow the heirarchy laid down in the
LUL Signs Manual section 6.8
Page 61
Typical Doorset Arrangements
DOUBLE LEAF FD60 EQUIPMENT ROOM DOOR WITHOUT GLAZING APERTURE
Furniture • L02R mortise sash lock with panic function E deadbolt and latch or L14R mortise sash
lock autofire panic action deadbolt and latch
• F13/1/2/3/4(D) on pierced backplates or F44/1/2/3/4(D) on escutcheons and roses pull/
lever handles
• 3 pair A1/SS/BMA or A4/SS/BMA hinges (for door in excess of 910x2100 use 4 pairs)
• 1 pair C7 overhead door closers
• 1 pair G3/G4/G2C barrel bolt sets
• K4 or K5 kick plates
note wall finishes and architraves omitted for clarity
Furniture - refer to Approved Ironmongery
for the Railway Environment for specific door
requirements
Signs - follow the heirarchy laid down in the
LUL Signs Manual section 6.8
Page 62
Typical Doorset Arrangements
SINGLE LEAF FD60 FINAL EXIT
Furniture • mortise panic action deadlatch
• F06 panic bar assembly with or without europrofile pierced cylinder pull.
• 1.5 pair A1/SS or A4/SS hinges (for door in excess of 910x2100 use 2 pairs)
• C7 overhead door closers
• K4 or K5 kick plates
note wall finishes and architraves omitted for clarity
Furniture - refer to Approved Ironmongery
for the Railway Environment for specific door
requirements
Signs - follow the heirarchy laid down in the
LUL Signs Manual section 6.8
Page 63
Typical Doorset Arrangements
DOUBLE LEAF FD60 FINAL EXIT
Furniture • mortise panic action deadlatch
• F06 & F07 panic bolt assembly with or without europrofile pierced backplate
• 3 pair A1/SS or A4/SS hinges (for door in excess of 910x2100 use 4 pairs)
• 1 pair C7 overhead door closers
• K4 or K5 kick plates
note wall finishes and architraves omitted for clarity
Furniture - refer to Approved Ironmongery
for the Railway Environment for specific door
requirements
Signs - follow the heirarchy laid down in the
LUL Signs Manual section 6.8
Page 64
SUPPLIERS
63(&,)<,1*,521021*(56672&.,676
$6*+DUGZDUH
Suite D4
.QLJKWV&RXUW
Archers Way
%DWWOHÀHOG(QWHUSULVH3DUN
Shrewsbury
SY1 3GA
7HO)D[
E-mail: [email protected]
Contact:
Andrew Harris
A trading division of Turentek (AI) Ltd.
0$,17(1$1&($1',167$//$7,216672&.,676
MLS Rail Ltd
8 Hillstone Court
Empson Street
London
E3 3LT
7HO
)D[
E-mail: [email protected]
Contact:
David Watkins
MANUFACTURERS
352'8&7
0$18)$&785(5
&217$&71R
Hinges
Royde & Tucker
Cooke Brothers
0192 274 0001
lnstinct Hardware
0121 459 2358
Pristine Engineering
'RRU)XUQLWXUH%URQ]H
Frank Allart & Co. Ltd
0121 454 2277
'RRU&ORVHUV
([LGRU'RRU&RQWUROV
Dorma Door Controls
Guardian Locks
Schulte-Schlagbaum Group
Surelock McGill Ltd
*8%.6
00 49 2051 201485
Surelock McGill Ltd
([LGRU
'RUPD8.
Surelock McGill Ltd
0118 977 2525
([LGRU
Davis Architectural Services Ltd
0208 853 5997
Securikey
01252 311 888
'RRU)XUQLWXUH666
/RFNV
6DIH([LW'HYLFHV
%DUUHO%ROWV
0LVFHOODQHRXV
Page 65
7KLVGRFXPHQWKDVEHHQSUHSDUHGXVLQJ$GREH,Q'HVLJQ&61HZ-RKQVRQDQG3.D]3URW\SHIDFHV,OOXVWUDWLRQVKDYHEHHQDVVVHPEOHGXWLOLVLQJ069LVLR
&RUHO'HVLJQHU;$&'&DQYDVDQG$GREH,OOXVWUDWRU&6
Page 66