FD90AID FD270AID

Transcription

FD90AID FD270AID
The patented design allows for versatility and possibilities in the
confines of the cockpit. The Flipper creates panel space where
none previously existed • Convenient stowable monitor displays EVS on the LCD that will
enhance the safety of your operation
• No requirement to cut new panel space for the installation or
upgrade to an expensive MFD or FMS
• Folds up to a horizontal stowed position when not in use. It uses
just over 1/2 inch of visible panel space
• One button selects video source- EVS, Weather, or Camera. The
video intensity backlighting can be adjusted by the BRT/DIM
buttons located on the side of the display
• Power supply and video input located in the Detached Electronics Box (DEB), which can be positioned up to 9 feet from
the Flipper (up to 15 foot cable available)
• Displays 2 composite video and 1 VGA input
• Both units are available in top or bottom mount
configurations to mount above or underneath the glare
shield and 90 degrees or 270 degrees of rotation from the
stowed position. The units are available in gray or black
DO-160 TESTED
Dimensions (Display)
Dimensions (DEB) Weight (Display) Weight (DEB-SM) Weight (DEB Cable)
Materials
Viewing Angles Aspect Ratio
Resolution
Supported Resolution
Brightness
Display Type
6.1” (W) x .66” (H) x .4.75” (D)
5.7” (W) x 1.14” (H) x 5.05” (D)
FD90AID - 1.22 lb, FD270AID - 1.20 lb
1.1 lb
.65 lb
Aluminum
180o on both axis
4:3
640x480
1280x1024
600 cd/m2
5.0487” TFT color LCD
Power PC Input Video Input
Video Type
12 - 28V @.5Amps - .3Amps
Analog RGB
2 Composite Video
VGA, NTSC/PAL
CURRENT AS OF 12/27/2010
DO-160 TESTED
FAA/PMA Approved
FD90AID
Shown: Top Mount
This is a sample of a top mount FD90AID.
A top mount unit always mounts on the topside
of the glareshield
This is a sample of a bottom mount FD90AID.
A bottom mount unit always mounts on the
underside of the glareshield
FD270AID
Shown: Bottom Mount
This is a sample of a top mount FD270AID.
This top mount unit always mounts on the
topside of the glareshield
This is a sample of a bottom mount FD270AID.
A bottom mount unit always mounts on the
underside of the glareshield
Allows unit to swivel left and right for viewing between pilot and co-pilot
• Available for :
FD90AID-T
FD90AID-B
FD90AID-ST
• Adds .175” height to unit and minimal weight
The slide mount is a variant of our popular Flipper. Perfect
for installation on top of a glareshield
• This monitor is completely enclosed in a box. It deploys
toward the user and then is rotated up 90 degrees
for viewing
• When not in use, the Flipper slides into its case where
approximately 1 inch is visible. In this stowed position,
power is automatically disconnected from the display
• Power supply and video input located in the Detached
Electronics Box (DEB) positioned 9 feet from the Flipper
(up to 15 foot cable available)
• Displays 2 composite video and 1 VGA input
Creates panel space where none previously existed, providing
an excellent opportunity to bring EVS video, satellite weather,
or any other VGA/Composite source into the cockpit with a
low-profile, stowing display
• Power supply and video input located in the Detached
Electronics Box (DEB) positioned 9 feet from the Flipper
(up to 15 foot cable available)
• Displays 2 composite video and 1 VGA input
• The display can be ordered in 2 different orientations;
with the control buttons on the right (FDPMAID-T) or
the left (FDPMAID-B)
• The units are available in gray or black
DO-160 TESTED
Dimensions (Display)
5.87” (W) x .165” (H) x 3.98” (D)
FD90AID-SMT
DO-160 TESTED
Dimensions (Display)
Dimensions (DEB) Weight (Display) Weight (DEB)
Weight (DEB Cable)
Materials
Viewing Angles FAA/PMA Approved
6.7” (W) x 1.07” (H) x 7.00” (D)
5.7” (W) x 1.14” (H) x 5.05” (D)
3.10 lbs
1.1 lb
.65 lb
Aluminum
180o on both axis FDPMAID
1
DO-160 TESTED
Dimensions (Display)
Dimensions (DEB) Weight (Display) Weight (DEB-SM) Materials
Viewing Angles 5.19” (W) x 4.78” (H) x .690” (D)
5.70” (W) x 1.60” (H) x 5.05” (D)
1.1 lbs 1.1 lbs
Aluminum
180o on both axis Designed for installation in piston general aviation aircraft, helicopters, and
any other aircraft with limited panel space
• Can be used to display Enhanced Vision Systems (EVS), Satellite Weather, or a standard video camera. Unlike the standard Flipper, the LG version is contained in a single box for easy installation
FD90AID-LG
• Designed to mount on top of the glareshield and flips up 90 degrees
for viewing. The Flipper-LG is automatically powered off when stowed
• The black LCD provides pilots with the ability to dim the backlighting
at night without losing picture quality and saving the pilot’s night vision
• Pilots can easily change the backlighting intensity by pushing the dim/
bright buttons on the face of the display
• Composite input (additional inputs available, contact Flight Display
Systems for additional information)
DO-160 TESTED
Dimensions (Display Enclosure)
Dimensions Deployed
Weight (Display)
Materials
Viewing Angles
FAA/PMA Approved
6.1”(W) x .70”(H) x 10.00”(D)
6.1”(W) x 4.82”(H) x 10.00”(D)
2.4 lbs
Aluminum
180o on both axis
Designed for installation in piston general aviation aircraft, helicopters, and
any other aircraft with limited panel space
• Can be used to display Enhanced Vision Systems (EVS), Satellite Weather, or a standard video camera. Unlike the standard Flipper, the ST version is contained in a single box for easy installation
• Designed to mount on top or underneath the glareshield and flips
90 degrees for viewing. The Flipper-ST is automatically powered off
when stowed
• The black LCD provides pilots with the ability to dim the backlighting at night without losing picture quality and saving the pilot’s night vision
• Pilots can easily change the backlighting intensity by pushing the
dim/bright buttons on the face of the display
• Composite input (additional inputs available, contact Flight Display
Systems for additional information)
FD90AID-ST
DO-160 TESTED
Dimensions (Display Enclosure)
Dimensions Deployed
Weight (Display)
Materials
Viewing Angles
FAA/PMA Approved
6.1”(W) x 1.375”(H) x 5.2”(D)
6.1”(W) x 5.45”(H) x 5.2”(D)
2.3 lbs
Aluminum
180o on both axis
Specifically designed for installation in helicopters to be mounted on the
side of the instrument panel, glareshield or sidewall, but is not limited to
helicopters
• Can be used to display Enhanced Vision Systems (EVS), Satellite Weather, or any composite video source. The Hinge Mount Flipper is contained in a single box with a 20 inch connector cable for ease of installation
• Mounts on the left or right side of an instrument panel or sidewall. The display swings out up to 150 degrees from its stowed position, and tilts 10 degrees forward and aft for adjustment of optimal viewing angle.
• Stows flush against it’s mounting plate and only occupies 1.38 inch of visible space
• Composite input (additional inputs available, contact Flight Display
Systems for additional information)
FD90AID-HMT
DO-160 TESTED
Dimensions (Display Enclosure)
Dimensions Deployed
Weight (Display)
Materials
Viewing Angles
7.40”(W) x 5.50”(H) x 1.38”(D)
7.40”(W) x 5.50”(H) x 7.97”(D)
2.4 lbs
Aluminum
180o on both axis
7” Flip down controller
Low-profile flipper
Creates panel space where none previously existed, providing an excellent
opportunity to bring EVS video, satellite weather, or any other VGA/Composite
source into the cockpit with a low-profile, stowing display
• “Face-Out” display, which the pilot can open 90 degrees to be viewed
• Available in top or bottom mount configurations; FD90AID-7-T for mounting
on the top of the glare shield and FD90AID-7-B for mounting on the underside
of the glare shield
• Larger than most MFDs at a fraction of the cost!
• Single piece unit, no detached electronics box required
• Extremely thin unit does not obstruct pilots view when stowed
FD90AID-7
• Displays 2 compostie video and 1 VGA input
• Automatically turns off when closed
DO-160 TESTED
Dimensions Closed
Dimensions Deployed
Power
Weight Materials
7.8”(W) x .89”(H) x 5.0”(D)
7.8”(W) x 4.7”(H) x 5.0”(D)
12 - 28V @.6Amps - .3Amps
1 lb 8 oz
Aluminum
10” Flip down controller
Low-profile flipper
Creates panel space where none previously existed, providing an excellent
opportunity to bring EVS video, satellite weather, or any other VGA/Composite
source into the cockpit with a low-profile, stowing display
• “Face-Out” display, which the pilot can open 90 degrees to be viewed
• Available in top or bottom mount configurations; FD90AID-10-T for mounting
on the top of the glare shield and FD90AID-10-B for mounting on the
underside of the glare shield
• Larger than most MFDs at a fraction of the cost!
• Single piece unit, no detached electronics box required
• Extremely thin unit does not obstruct pilots view when stowed
• Displays 2 compostie video and 1 VGA input
FD90AID-10
• Automatically turns off when closed
DO-160 TESTED
Dimensions Closed
Dimensions Deployed
Power
Weight Materials
10.5”(W) x .89”(H) x 6.6”(D)
10.5”(W) x 6.36”(H) x 6.6”(D)
12 - 28V @.6Amps - .3Amps
2 lbs 12 oz
Aluminum