Monogram Hanger

pink
project
Monogram Hanger
OUR PRODUCTS
• Queen Bee Paper (Honey Bee)
• Queen Bee 6 x 6 Paper Pad
(Various Papers)
• Queen Bee Punch Outs
• Queen Bee Bella Brads
• Queen Bee Ribbon Pleats
• Queen Bee Press Ons
SUPPLIES NEEDED
• Glue Gun
• Adhesive & Glue Dots
• Acrylic Paint
• Acrylic Circle (6")
• Chipboard Circle (5")
• Chipboard & Letter
• Scissors & Trimmer
• Foam Adhesive
• Ribbon
TO MAKE MONOGRAM
HANGER:
leaving the edges of the pleated
ribbon exposed.
Glue the
embellished ribbon pleat over the
STEP ONE
seam between the scallop edge
Gather the Artisan tape until there
and the top portion. Then tuck
are enough folds to form a circle.
in a strip of lace and glue it down
under the pleated ribbon.
STEP TWO
Begin by trimming a piece of
STEP FIVE
chipboard to 6” wide and 9 tall”
Paint your chipboard letter/
My door hanger is 9 inches high
monogram with acrylic paint in
including the scallop edge. Use
a coordinating color (I used a
a piece of scalloped paper,
Ranger paint applicator in Willow.)
chipboard or decorative ruler to
After the letter dries thoroughly,
help you create a scallop bottom.
carefully apply the press on over
the top of the letter. When you
STEP THREE
Cover the chipboard base with pull the rub on backing away from
1 ½ x 1 ½ patterned paper blocks. the letter after application, there
Ink the edges of all of the paper will be ‘rough’ edges left around
blocks with black chalk ink for the letters edge. With your finger,
added interest and cover the smooth the edges of the rub on
chipboard base with blocks – around the edges of the letter.
leaving the scallop bottom HOW TO CREATE THE RIBBON
uncovered.
CORSAGE FLOWER:
Use a hot glue gun
STEP FOUR
Cover the scallop bottom (or fabri-tac) for this process.
Monogram Hanger by angela moen
of the chipboard base with STEP ONE
yellow dot paper (honeybee). Cut a 4” piece of grey pleated
ribbon and reserve the entire strip
STEP FOUR
Create an embellished ribbon of the gold pleat. Begin with the
strip by layering various ribbons grey pleat first and apply a line
over the grey pleated ribbon of glue under the center stitch
of the grey pleat. Roll the pleat
into a ‘tube’. Now apply glue to
the bottom (under the center
stitch) of the entire gold pleat.
Continue to roll this pleat around
the grey pleat. While the glue is
still warm, mold the flower with
your hands, slightly pressing the
outside edges of the flower down
FOR MORE FREE PINK PROJECTS VISIT:
www.pinkpaislee.com/pink-projects/
pink
project
Monogram Hanger
to create a realistic flower.
STEP TWO
Snip the metal clasps off of the
gemstone brad. Squeeze an
ample amount of hot glue into the
center of your pleated flower and
set the gem brad into the center
of the flower.
center of the door hanger base
above the pleated ribbon, again
use foam tape for elevation.
STEP SIX
Cut out a pair of leaves from the
Honeybee patterned paper sheet.
STEP SEVEN
Assemble the leaves, corsage
STEP THREE
flower, stamp shaped Punchout,
Adding glue under the flower, and monogram to the front of the
I attached a few loops of sheer chipboard circle as desired.
ribbon to peek under the left
STEP EIGHT
hand side of the flower.
Punch 2 holes in the top of the
STEP FOUR
chipboard base and run ribbon
Cover a 5” chipboard circle with through the holes; tie in a bow on
the Worker Bee patterned paper. the front of the project.
STEP FIVE
STEP NINE
Attach the chipboard circle over Pucker the tails of the ribbon as
the center of the acrylic circle with desired and tack to the project
foam tape for elevation. Attach with glue dots as desired.
the circle components to the
FOR MORE FREE PINK PROJECTS VISIT:
www.pinkpaislee.com/pink-projects/