DRINKING FOUNTAIN INSTALLATION

DRINKING FOUNTAIN INSTALLATION
For all KEP( )AC-SBF Series Combination Fountains with Sports Bottle Filler
A. INSPECTION
Inspect the carton and water cooler for evidence of rough handling and concealed damage. Damage claims should be filed
with carrier.
B. TO PUT WATER COOLER AND FOUNTAIN INTO SERVICE
1. NOTE: Provincial and local plumbing codes may prohibit use of saddle taping valves for water line connection in some applications. All connections must conform to applicable plumbing codes.
2. Locate and install plumbing and electrical service if required, in accordance with the Rough-in Drawing. Filter units have
additional instructions on a label inside the access panel. Read these before installing unit.
3. FLUSH BUILDING WATER SUPPLY LINE BEFORE INSTALLING UNIT.
4. Install unit on the wall hanger. Wall hanger is shipped fastened to the back of the unit.
5. Install a trap in the waste line and a shut off valve in the water supply line. An in-line strainer is furnished in the “Water Supply” tube. Connect the “Water Supply” tube to the shut off valve. This connection should not be a solder joint or flare connection
to allow access to the strainer for service. To ease removal of the strainer, a sheet metal screw may be lightly threaded into the
open end. When the unit has an internal waste trap, the trap should be wrapped with the insulating tape to prevent sweating. Use
of the 1 3/4" diameter knockout for a waste line is not recommended because of a potential conflict with ADA* toe space clearance requirements. Check your local building code inspector for approval.
6. Rotate the fan blade by hand to see that it is free of obstructions.
7. Check the available power supply against the water cooler data plate to assure the correct electrical service. Plug power supply
cord into wall outlet. The rear most 1 3/8" diameter knockout in the frame bottom is for an externally located electrical supply.
Make sure the knockout hold edge is smooth and free of any burrs. Use of a Heyco bushing #2184 in the knocked out hole is
recommended in order to prevent damage to the service cord and to close up excess opening around the cord. Route the cord so
it does not interfere with ADA* space requirements.
8. To fill cold water tank on water cooler versions, open water supply line shut-off and push any one of the front or side
pushbuttons to allow water to flow to the bubbler. On the EE model, actuate the solenoid by holding one hand approximately 3"
from the infrared sensor. Run water until stream free of bubbles.
9. To Adjust Bubbler:
a) All Pushbutton models are equipped with a Cartridge Regulator. The KEP8AC and KEPAC have a slot in the shelf below the
Pushbuttons. Insert a screwdriver in the slot to adjust regulator. Turn adjustment clockwise to increase stream height. To access the KEPV8AC adjustment, remove the Bezel and Button from the front of the cooler.
b) Electric Eye (EE) models have a Regulator built into the the Bubbler. If adjustment is needed, insert a 5/64" wrench approximately 1 1/8" into the bubbler nozzle opening until it bottoms out and is seated in an adjust screw. Turn the adjust screw
clockwise to reduce stream height or counter clockwise to increase the height. Note: less than one turn is required to go from
a closed to a wide open flow. Do not over tighten the adjuster in the closed position as stripping the hex impression in the
adjust screw may result. Turn the adjuster 1/16 of a turn at a time.
10.On electic eye equipped models, place and then hold hand approximately 3" from the sensor to actuate the solenoid valve.
After approximately 30 seconds run time, the sensor will automatically shut off the solenoid valve. To reactivate, move hand away
for an instant and then again place it in front of the sensor.
0615
2000102863
1
DRINKING FOUNTAIN INSTALLATION
For all KEP( )AC-SBF Series Combination Fountains with Sports Bottle Filler
11.To adjust the beam range of the sensor (EE models only):
a) Shut off water and power supplies.
b) Remove the four screws from the top front.
c) Remove the eight screws from the bottom of the nose that holds the nose to the shelf.
d) Remove the nose to gain access to the sensor adjusting screw located between the two lenses.
e) The screw can be tuned a maximum of 3/4 turns. Turn screw counterclockwise to decrease range. The sensor has an adjustable range of 24" to 48". It is factory set at 27". There is a non-adjustable on-time delay of 0.75 seconds to prevent nuisance
actuation of the solenoid valve should someone walk by. NOTE: Walls with a reflective finish i.e., ceramic tile, across from the
sensor may cause false actuation no matter what the sensor adjustment is for distance. Therefore, do not install the unit in
such an area or dull the surface of the wall so it will not reflect light.
C. MAINTENANCE
The only maintenance operation required is the removal of dirt and lint from the condenser where used. Inspection should be made at
3-month intervals. Disconnect the power supply cord, then clean the condenser with a small stiff non-wire or vacuum cleaner attachment brush when required. Observance if this procedure will insure adequate air circulation through the condenser so operation is
efficient and economical.
D. OVERLOAD PROTECTION
The compressor motor, where used, is equipped with an automatic reset protector which will disconnect the motor from the line in
case of an overload.
E. LUBRICATION
This unit is equipped with a hermetically sealed compressor and requires no additional lubrication. The fan motor, where used, on this
unit seldom needs oiling, but if required, a few drops of SAE 10 oil should be used.
F. TO DISCONTINUE USE OF WATER COOLER
1. Close water shut-off valve.
2. Provide container to catch water to be drained.
3. On the push button model, disconnect the water supply line at the shut off valve and remove the tank drain plug. Actuate and hold
in the pushbutton to open the solenoid valve and completely drain the cooler. Disconnect the power supply cord.
4. On the EE model, disconnect the water supply line at the shut off valve and remove the tank drain plug. Actuate the solenoid, by
placing your hand approximately 3" in front of the sensor to completely drain the cooler. Disconnect the power supply cord.
5. Replace plug when draining is complete.
6. ALWAYS DRAIN ALL WATER WHEN FREEZING TEMPERATURES ARE ANTICIPATED AND BEFORE SHIPPING THE WATER COOLER.
*American With Disabilities Act
WARNING: The warranty and the Underwriters’ Laboratory Listing for this machine are automatically voided if this machine is
altered, modified, or combined with any other machine or device. Alteration or modification of this machine may cause serious flooding and/or hazardous electrical shock or fire. EXCEPT AS SET FORTH HEREIN, THE MANUFACTURER MAKES NO OTHER WARRANTY,
GUARANTEE OR AGREEMENT EXPRESSED, IMPLIED OR STATUTORY, INCLUDING ANY IMPLIED WARRANTY OR MERCHANT ABILITY
OR FITNESS FOR A PARTICULAR PURPOSE.
0615
2000102863
2
DRINKING FOUNTAIN ROUGH-IN
For all KEP( )AC-SBF Series Combination Fountains with Sports Bottle Filler
THIRD ANGLE PROJECTION
17 5/8 [447]
16 9/32 [413]
ROUGH-IN
AND
DIMENSIONAL DRAWING
NOTES:
1. TRAP, STOP VALVE AND ELECTRICAL OUTLET NOT FURNISHED.
2. ALLOW 4 INCHES [102 MM] MIN. PER SIDE FOR VENTILATON.
18 5/8
[472]
* 3. RECOMMENDED ADULT BARRIER FREE HEIGHT INSTALLATION
SHOWN. REDUCE HEIGHT BY 3 INCHES FOR INSTALLATIONS USED
PRIMARILY BY CHILDREN AGES 12 AND YOUNGER. UNIT SHALL ALSO
HAVE A MINIMUM CLEAR FLOOR SPACE 30[760] BY 48[1220]. ADJUST
VERTICAL DIMENSIONS AS REQ’D TO COMPLY WITH PROVINCIAL
AND LOCAL CODES.
4. ALL DIMENSIONS ARE IN INCHES. DIMENSIONS IN BRACKETS [ ] ARE
IN MILLIMETERS.
PUSH PADS
BOTTLE FILLER
BUTTON
7/16 [11]
1/2 [13]
16 1/32
[407]
1 1/4 IPS WASTE
OPTIMUM LOCATION
STUB OUT 1[25] INCH
48
[1218]
7/16 [11]
51
[1297]
7/8 [22]
33 3/8
[848]
AIR
FLOW
5 1/4
[133]
13 7/8
[352]
*29 5/16
[745]
21 1/4
[539]
*27
[687]
1 1/4 O.D.
TAILPIECE
3/8 O.D.
WATER INLET
WITH STRAINER
18 1/16
[459]
4 [99]
7 [8]
17
[432]
16 1/2
[419]
1/2 [10]
ELECTRICAL
OUTLET OPTIMUM
LOCATION
12 3/4 [324]
15 7/18 [392]
0615
2000102863
3
DRINKING FOUNTAIN INSTALLATION
For all KEP( )AC-SBF Series Combination Fountains with Sports Bottle Filler
This bottle filler is an extension of the drinking fountains
product line.
It is mounted directly to an existing unit and no additional
electrical connections are required. If installed into a refrigerated drinking fountain, chilled water can be dispensed through
the bottle filler. Otherwise, room temperature water will be
dispensed.
The bottle filler kit is shipped partially assembled.
WHEN COMPLETED, THE FINISHED ASSEMBLY WILL LOOK LIKE THIS:
0615
2000102863
4
SECTION 1: GETTING STARTED
NOT PRE-DRILLED/BOTTLE FILLER KIT:
If the unit is not pre-drilled or you purchased a BOTTLE FILLER retrofit KIT,
go to PAGE 6A.
PRE-DRILLED/PLUMBED:
If your unit was purchased pre-drilled and plumbed at the factory as a COMBINATION, go to PAGE 12C.
WHAT’S INCLUDED?
TOOLS REQUIRED:
1. Top cap
2. 38" of 1/4 OD plastic tubing with 19" of sponge tubing insulation
3.Gasket
4. Quick connect tee fitting (only required on split level models)
5. Installation instructions
6. Drip tray
7. Anti splash grate
8. Anti Splash grate screws (2)
9. Snap bushing
10. Wrap-around cabinet facing
11. Hands-free sports bottle filler
- 3/8" drill bit that will drill through stainless steel top
- Electric drill
- Small tubing cutter for copper tube
- T15 Torx driver with pin in head vandal tip
- T20 Torx driver with pin in head vandal tip
- 1/4" nut driver
- #2 Phillips screw driver
6.
2.
1.
7.
3.
4.
8.
10.
5.
9.
11.
0615
2000102863
5
SECTION 2: PRESSURIZING THE COOLING TANK
The water should already be turned OFF and the power DISCONNECTED.
A. NON-PRESSURIZED COOLING TANK
If the cooling tank is non-pressurized, follow these instructions. Otherwise, proceed to SECTION 3.
Water
valve/regulator
NON-PRESSURIZED
COOLING TANK
0615
2000102863
Supply
Water
Cooling
tank
Supply
Water
Cooling
tank
Water
valve/regulator
PRESSURIZED
COOLING TANK
6
SECTION 2: PRESSURIZING THE COOLING TANK
A. NON-PRESSURIZED COOLING TANK (continuation)
STEP 1
Unit as it appears with top removed.
STEP 2
Unplug un-insulated water line from water valve inlet (JG
elbow located left side of water valve facing the front of
the cooler). Set tubing aside (being careful to not contaminate the water contact in of the tube).
STEP 3
Unplug tubing from JG elbow leading to cooling tank inlet.
0615
2000102863
7
SECTION 2: PRESSURIZING THE COOLING TANK
A. NON-PRESSURIZED COOLING TANK (continuation)
STEP 4
Plug un-insulated tubing that was removed in Step 1 into
JG elbow leading to the cooling tank from Step 3.
STEP 5
Unplug tubing that is onnected to the water valve outlet
(JG elbow located on the right side of valve facing the
cooler.
STEP 6
Connect tubing from Step 5 to JG elbow on the left side of
the valve.
0615
2000102863
8
SECTION 2: PRESSURIZING THE COOLING TANK
A. NON-PRESSURIZED COOLING TANK (continuation)
STEP 7
Unplug JG tubing from the cooling tank outlet. Do not set it down.
STEP 8
Using tubing removed in Step 7, plug into JG elbow on the right
side of the valve. (Be sure to re-route the tubing under existing
tubing installed in Step 5 as shown.
STEP 9
Using tubing that is connected to the JG elbow left side of valve
(done in Step 5, plug the other end to the JG fitting at the top of
the cooling tank.
0615
2000102863
9
SECTION 3: INSTALLATION
WATER COOLER INSTALLATION INSTRUCTIONS, MODELS: KEPWSBF
SECTION 3: CONNECTING THE WATER LINE
DRINKING FOUNTAIN
A. DRILLING HOLE IN THE TOP FOR WATER LINE CONNECTION
1. Disconnect power by UNPLUGGING unit. It might be necessary to remove the front panel to get access to the power.
2. Turn OFF water supply to the unit. It might be necessary to remove the front panel to access the water stop valve.
B. RETROFIT or FOUNTAIN/FRAME - PRESSURIZED
3.
template
onto cooler top and
so it is
aligned with the left side of unit and wall. (TEMPLATE FOUND ON PAGE 17)
Place
(for hole
units
not pre-plumbed
pre-drilled)
4. Mark hole location.
a) Disconnect power by UNPLUGGING unit. It might be necessary to remove the front panel to get access to the power.
5. Remove
unit.
(Figure
1) unit. It might be necessary to remove the front panel to access the water stop valve.
b) Turn top
OFFfrom
water
supply
to the
6. Using
a 3/8
drill
bit, drillonto
a hole
through
top.it is aligned with the left side of unit and wall. SEE NEXT PAGE FOR TEMPLATE.
c) Place
hole
template
cooler
top so
d) Mark
hole
location.
7. Install
snap
bushing
into hole to protect tubing from being cut. (Figure 2)
Template
Figure 2
Figure 1
Mark hole location
Drill
Install Bushing
Remove top from cooler by
removing six #15 torx head
screws on sides of top.
e) Remove top from unit. (Figure 1)
B. CONNECTING
THE WATER LINE
f) cooling
Using atank
3/8isdrill
bit, drill a hole through
If the
non-pressurized,
then gotop.
to the "Pressurizing the cooling tank" addendum section. Otherwise, proceed to
g)
Install
snap
bushing
into
hole
to
protect
(Figure
2)
STEP 1 next page. Non-pressurized units are tubing
single from
unitsbeing
madecut.
since
December
of 2009. Refer to the schematic below to identify
the system that you have.
Water
valve/regulator
NON-PRESSURIZED
COOLING TANK
0112
036865-003
0615
2000102863
Supply
Water
Cooling
tank
Supply
Water
Cooling
tank
Water
valve/regulator
PRESSURIZED
COOLING TANK
5
10
ALIGN DASHED EDGE WITH LEFT EDGE OF COOLER TOP
2 1/8"
[5.4 cm]
FROM BACK
Mark this center point on the.
top. Remove the top from the
cooler. Then drill a 3/8" [9.5mm] hole
through the top at the marked
center point.
PLACE THIS DASHED EDGE AGAINST WALL
3 1/4"
[8.25 cm]
FROM SIDE
USE THIS TEMPLATE TO MARK THE HOLE
LOCATION ON COOLER TOP
0615
2000102863
11
SECTION 3: CONNECTING THE WATER LINE
DRINKING FOUNTAIN
C. CONNECT THE BOTTLE FILLER TUBE
This tube supplies cold water from the cooling tank to the Bottle Filler.
¼" OD tube to connect
to Bottle Filler
a) First, remove plug from fitting on tank drain.
b) Next, insert end of tube into fitting.
c) Feed tubing up through the top and attach the top to the cooler. (Figure 1) Figure101
Figure
0615
2000102863
12
SECTION 4: MOUNTING THE FRAME TO THE WALL
STEP 1:
Place rubber gasket on top of the cooler so it is centered left/right and against the wall. (Figure 11)
STEP 2:
Set the wall frame onto the gasket. Center it left/right and push it against the wall and mark hole locations for wall fasteners. The gasket will
set the frame at the proper height. (Figure 12)
STEP 3:
Secure frame to the wall with fasteners (not provided). Pull plastic tubing up through the hole in the frame. Use mounting slots that will provide
the proper securing location. Make sure to pull the plastic tubing up through the hole in the frame.
Figure 11
Make sure to pull
the plastic tubing
up through the
hole in the frame.
STEP 4:
Figure 12
Use mounting
slots that will
provide the proper
securing location.
Figure 13
Slide sponge tubing insulation over water line.
Connect the tubing to the INLET elbow on the
back of the bottle filler assembly. (Figure 13)
Connect tube to elbow
on the valve
Plastic tubing
Sponge tubing insulation
REAR VIEW OF BOTTLE FILLER
STEP 5:
Set the bottle filler
cabinet into place.
MAKE SURE the cabinet
fits into the groove in
the rubber gasket on
both sides and front of
the cabinet wrapper.
(Figure 14)
0615
2000102863
Figure 14
Bottle filler cabinet
Groove in the gasket
13
SECTION 4: MOUNTING THE FRAME TO THE WALL (cont'd)
STEP 6:
Attach Bottle Filler assembly and top cap to the frame using the six (6) vandal resistant torx screws. (Figure 15)
Figure 15
Torx screws
STEP 7:
Install the drip tray and anti-splash grate into the alcove area and secure with the two (2) stainless steel Phillips head screws. (Figure 16)
STEP 8:
Turn ON water supply and check for leaks. Press the activation button and release any trapped air from the system. Plug in the power cord and
replace the front panel IF it was removed earlier. (Figure 17)
Figure 16
Figure 17
Anti-splash
grate screws
(provided)
Press
Anti-splash
grate
Drip tray
INSTALLATION COMPLETE
0615
2000102863
14
EXPLODED PARTS BREAKDOWN
SPORTS BOTTLE FILLER
25
33
26
12
13
29
19
24
16
14
3
17
15
28
2
27
18
1
32
20
9
22
30
21
8
23
4
6
22
22
11
25
10
5
31
7
22
0615
2000102863
15
EXPLODED VIEW LIST OF PARTS
SPORTS BOTTLE FILLER
1. 036190-002 2. 036691-001 3. 036686-001 4. 036049-002
5. 036688-001 6. 036695-001 7. 036697-001 8. 036194-002 9. 034649-001 10.036689-001 11.036191-002 12.035990-001 13.029967-002 14.A020957
15.036690-001 16.030176-002 17.028706-036 18. 026670-007 19. 028481-101 20. 036209-001 21.026642-003 22. 026642-003 23.031206-005 24.030152-046 25.031875-003
26.036687-001 27.027189-007 28.029199-103 29.030152-031 30.017681-008 31.036701-001 32.036702-001 33.036231-001-SP
Alcove
Wrapper
Cap
Screw, flat head tapping
Tray, drip
Tray, grille drip
Bottom cap for drip tray
Button
Spring
Gasket
Drain, short
Holder, cartridge stem connector
Cartridge
Nut, retaining plastic
Bracket, valve
Plug, hole
Washer/spacer/gasket-non metallic
Screw, hex heavy duty machine
Fitting, PP union elbow white
Fill tube assembly
Bracket, fill tube support
Screw, hex heavy duty tapping
Insert, nameplate “Aquapointe”
Tube, PE cut length white
Screw, button heavy duty tapping
Frame
Bushing, snap
Fitting, PP untion tee white
Tube, PE cut length white
Insulation, sponge tubing
Drip tray assembly, service
Button assembly, service
Valve assembly, dispense-service
Accessory Kits
036704-001 SRH-KEPWSBF
EKG-KEPWSBF Vandal resistant screw kit - Includes torx bits and replacement screws for items 4, and 25
Gasket, Sunroc/Haws #036689-101 - Replaces item 10
Gasket, Elkay/Halsey Taylor #036689-201 - Replaces item 10
Haws is a registered trademark of HAWS Corporation.
Elkay and Halsey Taylor are registered trademarks owned or licensed by Elkay Sales Inc. and/or its parent Elkay Manufacturing Company.
0615
2000102863
16
SPECIFICATIONS
CHILLED DRINKING FOUNTAIN
Voltage
Size
Shipping Weight (Approx)
Cold Water Capacity*
Compressor
Compressor (Full Load)
Refrigerant
Refrigerant Charge
Room Temperature
Supply Water Temperature Drinking Water Temperature
115 VAC±10%/1 PH/60 Hertz
17 5/8" W, 18 5/8" D, 18 29/32" H
59 lbs.
8 GPH
1/4 hp
4.4 amps
134a
3.95 OZ
90◦F
80◦F
50◦F
Specifications subject to change without notice.
0615
2000102863
17
EXPLODED PARTS BREAKDOWN
DRINKING FOUNTAIN
To adjust stream height, insert a 1/8" flat blade screwdriver into
the slotted hole as shown. The screwdriver will engage the stream
height adjuster in the cartridge plunger. Turn clockwise to increase
stream height or counter clockwise to reduce stream height.
0615
2000102863
18
PARTS BREAKDOWN LIST
DRINKING FOUNTAIN
Item
Single
Split Level
Single
#Description...............................................................Chilled.......................Chilled....................... Non-chilled
1.Top............................................................................ 031714-101...............031714-101............... 031714-101
2.Bubbler..................................................................... 035607-108...............103607-108............... 035607-108
3. Washer, under top..................................................... 028706-030...............028706-030............... 028706-030
4.Locknut..................................................................... 026824-019...............026824-019............... 026824--109
5. Bubbler nut W/ JG (John Guest)................................ 036026-001...............036026-001............... 036026-001
6.Condenser................................................................ 031766-201...............031766-201............... Not applicable
7. Side panel, Left – Sandstone .................................... 035080-009...............035080-309............... 035080-009
Side panel, Left – Greystone .................................... 035080-001...............035080-301............... 035080-001
Side panel, Left – Stainless Steel.............................. 035080-010...............035080-310............... 035080-010
8. Blade, fan.................................................................. 024033......................024033...................... Not applicable
9. Motor, fan................................................................. 027354-036...............027354-036............... Not applicable
10. Bracket, fan motor.................................................... 036478-001...............036478-001............... Not applicable
11. Drain screw............................................................... 036049-002...............036049-002............... 036049-002
12. Waste gasket............................................................. 031756-002...............031756-002............... 031756-002
13. Hanger bracket......................................................... 031363-002...............031363-002............... 031363-002
14. Side panel, Right - Sandstone.................................... 035081-009...............035081-009............... 035081-309
Side panel, Right - Greystone.................................... 035081-001...............035081-001............... 035081-301
Side panel, Right - Stainless Steel............................. 035081-010...............035081-010............... 035081-310
15. Patch plate - Sandstone............................................ Not applicable............036142-009............... 036142-009
Patch plate - Greystone............................................. Not applicable............031642-001............... 031642-001
Patch plate - Stainless Steel...................................... Not applicable............031642-010............... 031642-010
16. Service cord.............................................................. 026540-045...............026540-045............... Not applicable
17.Frame....................................................................... 035089-001...............035089-001............... 035089-001
18. Waste assembly........................................................ 036011-001...............036011-002............... 036009-002
19. Insulation, right cooling tank..................................... 035088-001...............035088-001............... Not applicable
20. Insulation, left cooling tank....................................... 035088-002...............035088-002............... Not applicable
21. Cooling tank, insulated.............................................. 035469-055-SP..........035469-055-SP.......... Not applicable
22. Cold control.............................................................. 027040-039...............027040-039............... Not applicable
23.Relay......................................................................... 036056-003...............036056-003............... Not applicable
24.Overload................................................................... 036055-003...............036055-003............... Not applicable
25. Start capacitor — 60 MFD......................................... 027956-008...............027956-008............... Not applicable
26. Run capacitor —25 MFD............................................ 027956-009...............027956-009............... Not applicable
27. Compressor assembly............................................... 036115-001...............036115-001............... Not applicable
28. Front panel, Right - Sandstone.................................. 035079-009...............035079-009............... 035079-009
Front panel, Right - Greystone................................... 035079-001...............035079--001.............. 035079--001
Front panel, Right - Stainless Steel............................ 035079-010...............035079-010............... 035079-010
29. Front nose piece - Sandstone.................................... 035077-009...............035077-009............... 035077-009
Front nose piece - Greystone.................................... 035077-001...............035077-001............... 035077-001
Front nose piece - Stainless Steel............................. 035077-010...............035077-010............... 035077-010
30. Activation assembly.................................................. 035412-004...............035412-004............... 035412-004
31. Water line, tank to valve............................................ 035504-011-SP..........035504-011-SP.......... 035503-001
Water line, inlet to valve or tank................................. 035504-010-SP..........035504-010-SP.......... Not applicable
32. Union elbow fitting JG (John Guest)............................ 02481-101.................028481-101............... 028481-101
33. Cartridge holder........................................................ 035990-00.................035990-001............... 035990-001
34.Cartridge................................................................... 029967-002...............029967-002............... 029967-002
35. Retaining nut, cartridge............................................. A020957....................A020957.................... A020957
36. Water line, tank or valve to bubbler............................ 035504-013-SP..........035504-013-SP.......... 035504-013-SP
37.Shelf......................................................................... 035078-002...............035078-002............... 035078-002
38.Dryer......................................................................... 034343-003...............034343-003............... Not applicable
39. Activation shelf......................................................... 035092M101.............035092M101............. 035092M101
40. Waste tee.................................................................. Not applicable............A020968.................... A020968
41. Waste arm assembly................................................. Not applicable............026980-004............... 0269980-004
42. Waste elbow.............................................................. Not applicable............A020967.................... A020967
43. Waste extension tube................................................ Not applicable............036010-016............... 036010-016
Parts Not Shown:
Strainer, in-line.......................................................... 033264-003...............033264-003............... 033264-003
0615
2000102863
19
WIRING DIAGRAM
DRINKING FOUNTAIN
WIRING DIAGRAM
Single KEP(_)
KEP(__)Series
series,
Single
Split Level KEP (__) series
Split Level KEP(_)ACSL Series
Franke Kindred Canada Limited
Franke Commercial Systems
1000 Franke Kindred Road
Midland, ON L4R 4K9
Tel 1.855.446.5663
Fax 1.866.227.3050
www.franke-commercial.com
0615
2000102863