fasteners - Von Rohr :: Equipment Corp.

KASS
Headquarters
INDUSTRIAL SUPPLY CORP.
ANCHORING
FASTENERS
Fig.
61
POWER TOOLS
& ACCESSORIES
Fig.
61A
Fig. 62
Fig. 63
CONTRACTOR
SUPPLY
Fig.
10
DRYWALL SUPPLY
& HAND TOOLS
Fig.
11
ADHESIVES
& SEALANTS
Fig.
12
AIR & GAS
NAILERS
Fig.
27A
Catalog
No.
Fig.
No.
Description
K-8
K-12
K-16
K-20
KX
61
61
61
61
61A
1/2” EMT to 1/4” and smaller rods or flanges
3/4” EMT to 1/4” and smaller rods or flanges
1” EMT to 1/4” and smaller rods or flanges
1-1/4” EMT to 1/4” and smaller rods or flanges
BX Number 8 wire
2-FMP-2-8
2-1-2-4
4-1-2-4
62
63
64
Multi-Purpose Clip 1/8” - 1/2” flange
Low Voltage Clip for bridle or drive ring to 1/4” rod, No. 8 or No. 12 wire
Low Voltage Clip 1/4” - 20 thread (for bridle ring or screw) to 1/4” rod,
No. 8 or No. 12 wire
708-2-4
708-5-8
708-9-12
6-A-2-4
6-A-5-8
6-A-9-12
10
10
10
10A
10A
10A
1/8” - 1/4” flange #8 wire or 1/4” rod
5/16” - 1/2” flange - #8 wire or 1/4” rod
9/16” - 3/4” flange - #8 wire or 1/4” rod
1/8” - 1/4” flange - 3/8” rod
5/16” - 1/2” flange - 3/8” rod
9/16” - 3/4” flange - 3/8” rod
4-TI-2-4
4-TI-5-8
4-TI-9-12
6-TI-2-4
6-TI-5-8
6-TI-9-12
11
11
11
11
11
11
1/8” - 1/4” flange - 1/4” threaded rod, with thread impression
5/16” - 1/2” flange - 1/4” threaded rod, with thread impression
9/16” - 3/4” flange - 1/4” threaded rod, with thread impression
1/8” - 1/4” flange - 3/8” threaded rod, with thread impression
5/16” - 1/2” flange - 3/8” threaded rod, with thread impression
9/16” - 3/4” flange - 3/8” threaded rod, with thread impression
6-TA-2-4
6-TA-5-8
6-TA-9-12
12
12
12
1/8” - 1/4” flange - 1/4” or 3/8” threaded rod, nuts required
5/16” - 1/2” flange - 1/4” or 3/8” threaded rod, nuts required
9/16” - 3/4” flange - 1/4” or 3/8” threaded rod, nuts required
708AB
6-A-B
4-TI-B
6-TI-B
6-T-B
708AO
6-A-O
4-TI-O
6-TI-O
6-T-O
27
27A
28
28
29
30
30A
31
31
31
Angle Bracket for No. 8 Wire or 1/4” plain rod
Angle Bracket for 3/8” plain rod
Angle Bracket for 3/8” threaded rod, with thread impression
Angle Bracket for 3/8” threaded rod, with thread impression
Angle Bracket for 1/4” or 3/8” threaded rod, nuts required
Offset Bracket for No. 8 wire or 1/4” rod
Offset Bracket for 3/8” plain rod
Offset Bracket for 1/4” threaded rod, with thread impression
Offset Bracket for 3/8” threaded rod, with thread impression
Offset Bracket for 1/4” or 3/8” threaded rod, nuts required
Fig. 64
Fig.
10A
Fig.
27
Fig.
28
Fig. 30
FASTENERS
282
BRONX, NEW YORK
Ph: 718-299-6060 • Fx: 718-299-1593
Toll Free: 800-255-0910
Fig. 30A
®
®
Fig. 32
Fig. 31
Fig. 29
Ph: 914-777-3245
Fx: 914-777-3875
Ph: 631-234-0740
Fx: 631-234-0686
Ph: 215-244-1545
Fx: 215-244-1082
Pennsylvania
FASTENERS
Fig.
No.
Description
2-B-1 5L-S
4-B-1 5L-S
4-B-1 5L
4-B-2 5S
67
67
68
67
No. 8 wire to 1-1/2” lathers channel side mount
1/4” rod to 1-1/2” lathers channel side mount
1/4” rod to 1-1/2” lathers channel
1/4” rod to 2” lathers channel
4-G-16
4-G-16-G
4-G-16-1.5
4-G-16-2
4-G-16-3
4-WN
4-G-16-H
70
70
70
70
70
71
72
Twist Clip for acoustical tee bar (stud 1/4” -20 x 5/8” long)
Twist Clip for acoustical tee bar Painted Aluminum (stud 1/4” -20 x 5/8” long)
Twist Clip for acoustical tee bar Painted Aluminum (stud 1/4” -20 x 1-1/2” long)
Twist Clip for acoustical tee bar Painted Aluminum (stud 1/4” -20 x 2” long)
Twist Clip for acoustical tee bar Painted Aluminum (stud 1/4” -20 x 3” long)
Washer Nut 1/4” -20 thread impression
Twist Clip for acoustical tee bar for sign hanging
MSC
MSF
76
80
Metal Stud Box Support
Metal Stud Box Support
DH-2
DH-708
DH-6-A
DH-4-T1
DH-6-TI
DH-6-T
33
35
34A
34
34
36
Decking-wrapping wire, “S” hooks, bolting straps
Decking for No. 8 wire or 1/4” rod
Decking 3/8” rod
Decking 1/4” threaded rod, with thread impression
Decking 3/8” threaded rod, with thread
Decking 1/4” or 3/8” threaded rod, nuts required
BHA
OBHA
BHC
BPH
BHR
W9003-5
89
90
91
92
—
—
Bar Hanger Assembly (includes: 1 Bar 26”, 1 Mounting Clip, 2 Bar Retainer Clips & 1 Screw)
Offset Bar Hanger
Box Mounting Clip
Metal Stud Punch
Retainer Cap
Replacement Punch
Fig. 98A
708
6-A
98
98A
No. 8 wire or 1/4” rod
3/8” rod
Fig. 100
AB
AO
99
100
Angle Bracket
Offset Bracket
BC
1
Beam Clamp thru 1/2” flange
Fig. 71
Fig. 72
Fig. 80
Fig.
76
Fig.
34
Fig.
34A
Fig.
35
Fig.
36
Fig. 90
Fig. 89
Fig.
92
Fig. 91
Fig. 98
Fig. 99
Fig. 1
CONTRACTOR
SUPPLY
Fig. 70
AIR & GAS
NAILERS
Fig.
68
POWER TOOLS
& ACCESSORIES
Catalog
No.
Fig.
67
Fig.
33
ANCHORING
FASTENERS
®
Fig. 8
Fig. 7
2-H-4
4-H-2-4
4-H-5-8
8
7
7
3/32” - 9/64” flange
1/8” - 1/4” flange
5/16” - 1/2” flange
DRYWALL SUPPLY
& HAND TOOLS
BENSALEM
Long Island
ADHESIVES
& SEALANTS
ISLANDIA
New York
®
FASTENERS
MAMARONECK
283
KASS
Headquarters
INDUSTRIAL SUPPLY CORP.
ANCHORING
SammyS™ and SidewinderS™
verTical mounT For wood
Sidewinder mounT For wood
POWER TOOLS
& ACCESSORIES
rod Size
caT no.
deScriPTion
box qTy.
rod Size
caT no.
deScriPTion
box qTy.
1/4”
1/4”
1/4”
1/4”
1/4”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
1/2”
1/2”
1/2”
1/2”
1/2”
8001957
8002957
8003957
8004957
8005925
8006957
8007957
8008957
8009925
8010957
8011925
8012925
8013925
8014925
8015925
8016925
8017925
1/4 x 3/4
1/4 x 1
1/4 x 2
1/4 x 3
1/4 x 6
1/4 x 3/4
1/4 x 1
1/4 x 2
3/8 x 2-1/2
1/4 x 3
1/4 x 4
1/4 x 6
1/4 x 2
3/8 x 2-1/2
1/4 x 3
1/4 x 4
1/4 x 6
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
1/4”
1/4”
3/8”
3/8”
3/8”
3/8”
8018957
8019957
8020957
8021957
8022925
8023925
1/4 x 1
1/4 x 2
1/4 x 1
1/4 x 2
3/8 x 2-1/2
1/4 x 3
25
25
25
25
25
25
CONTRACTOR
SUPPLY
verTical mounT For STeel
DRYWALL SUPPLY
& HAND TOOLS
ADHESIVES
& SEALANTS
rod Size
caT no.
deScriPTion
box qTy.
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
1/2”
1/2”
1/2”
1/2”
1/2”
1/2”
8024957
8025957
8026957
8027957
8028957
8029957
8030957
8037957
8038957
8039957
8040957
8041957
8042957
8043957
8044957
8045957
8046957
8031925
8032925
8033925
8034925
8035925
8036925
1/4-20 x 1
1/4-14 x 1
1/4-14 x 1-1/2
1/4-14 x 2
1/4-12 x 2-1/2
1/4-14 x 3
12-24 x 1-1/2
12-24 x 1-1/2
1/4-20 x 1
5/16-18 x 1-1/4
1/4-14 x 1
1/4-12 x 1-1/2
1/4-14 x 2
1/4-14 x 2-1/2
1/4-14 x 3
5/16-18 x 1-1/4
12-24 x 1-1/2
1/4-14 x 2
1/4-14 x 2-1/2
1/4-20 x 1
5/16-18 x 1-1/4
5-16-18 x 1-1/4
12-24 x 1-1/2
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
verTical mounT For concreTe
rod Size
caT no.
deScriPTion
box qTy.
1/4”
3/8”
1/2”
8058957
8059957
8060925
5/16 x 1-1/2
5/16 x 1-1/2
5/16 x 1-1/2
25
25
25
Sidewinder mounT For STeel
rod Size
caT no.
deScriPTion
box qTy.
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
8050957
8051957
8052957
8053957
8054957
8055957
8056957
8057957
1/4-14 x 1
1/4-14 x 1-1/2
1/4-14 x 2
5/16-18 x 1-1/4
1/4-20 x 1-1/2
1/4-20 x 1-1/2
5/16-18 x 1-1/4
12-24 x 1-1/2
25
25
25
25
25
25
25
25
Sidewinder mounT For concreTe
rod Size
caT no.
deScriPTion
box qTy.
1/4”
3/8”
8062957
8061957
5/16 x 1-1/2
5/16 x 1-1/2
25
25
nuT driverS
Use #14SW Nut Driver for
Sidewinders and 1/2” Rod
Sammys
ParT no.
0238114910
color
Red
Use #14 Nut Driver for
Sammys and Swivel Head
ParT no.
0238113910
color
Black
AIR & GAS
NAILERS
Sammy Swivel head™
hang Threaded rod directly fromThin
gauge metal deck & Purlin
• Use with 3/8” Rod
• 17˚ deflection from vertical
• Accommodates up to 3-1/2 x 1/2 pitch roof
• Also available in stainless steel
• Use #14 Nut Driver (black)
Sammy Swivel head For wood
uninstalled
installation
Tool
installed
FASTENERS
284
BRONX, NEW YORK
Ph: 718-299-6060 • Fx: 718-299-1593
Toll Free: 800-255-0910
STeel ga.
caT no.
deScriPTion
box qTy.
22-20
18-16
8150922
8153922
8151910
1/4-20 x 1-1/8
1/4-20 x 1-1/8
Sammy X-Press It
(Installation Tool)
25/64” Drill Bit
25
25
1
8152910
1
caT no.
deScriPTion
box qTy.
8139957
8140957
8141957
8142957
1/4 x 2
1/4 x 2
1/4 x 3
1/4 x 3
25
25
25
25
Sammy Swivel head For STeel
caT no.
deScriPTion
box qTy.
8137957
8138957
1/4-20 x 1
1/4-20 x 1
25
25
Pennsylvania
EYE BOLTS
Catalog No.
(Thread dia. x O.A. Length)
MACHINE THREAD WITH HEX NUT
Zinc chromate finish steel
with hex nut assembled
FCL 1970
Catalog No.
(Thread dia. x O.A. Length)
514
514
514
514
514
514
514
514
514
3/16 x 1-3/4 (2A)
3/16 x 2-1/4 (2B)
3/16 x 2-1/2 (2S)
3/16 x 2-3/4 (2C)
3/16 x 3 (2D)
1/4 x 2 (4R1)
1/4 x 2-1/2 (4R2)
1/4 x 3 (4S3)
1/4 x 4 (4A)
FASTENERS
Model
No.
Thread
Size
Shank
Lgt. (in.)
Thread
I.D.
Lgt. (in.) Eye (in.)
10769
10771
10772
10773
10774
10800
10802
10803
10805
10-24
10-24
10-24
10-24
10-24
1/4-20
1/4-20
1/4-20
1/4-20
1
1-1/2
1-3/4
2
2-1/4
1
1-1/2
2
3
7/8
1-3/8
1-5/8
1-7/8
2-1/8
7/8
1-3/8
1-3/4
2-3/4
3/8
3/8
3/8
3/8
3/8
9/16
9/16
9/16
9/16
TURNBUCKLES
514
514
514
514
514
514
514
514
514
514
514
514
514
514
1/4 x 5 (4B)
1/4 x 6 (4C)
1/4 x 8 (4E)
5/16 x 2-1/4 (5S)
5/16 x 3-1/4 (5R)
5/16 x 4 (5A)
5/16 x 5 (5B)
5/16 x 6 (5C)
5/16 x 8 (5E)
3/8 x 2-1/2 (6S)
3/8 x 4 (6R)
3/8 x 5 (6A)
3/8 x 6 (6B)
3/8 x 8 (6C)
Model
No.
Thread
Size
Shank
Lgt. (in.)
Thread
I.D.
Lgt. (in.) Eye (in.)
10807
10808
10810
10836
10839
10841
10843
10845
10849
10873
10875
10877
10878
10880
1/4-20
1/4-20
1/4-20
5/16-18
5/16-18
5/16-18
5/16-18
5/16-18
5/16-18
3/8-16
3/8-16
3/8-16
3/8-16
3/8-16
4
5
7
1
2
2-1/2
3-1/2
4-1/2
6-1/2
7/8
2-1/4
3-1/4
4-1/4
6-1/4
3
9/16
3
9/16
3
9/16
7/8
3/4
1-3/4 3/4
2-1/4 3/4
3
3/4
3
3/4
3
3/4
3/4
1
2
1
3
1
3
1
3
1
KASS ALSO STOCKS A VARIETY OF STYLES AND
SIZES OF THE FOLLOWING ITEMS—ALL AVAILABLE
IN ZINC CHROMATE FINISH STEEL
Aluminum bodies with zinc chromate steel eyes and hooks
Aluminum bodies have hex ends for easy adjustment
SCREW EYES
EYE-EYE
Catalog
Number
Model
No.
Thread
Size
Take
Up
Length
Closed
Length
Open
11
12
13
14
15
16
17
11369
11370
11371
11372
11373
11374
11375
5/32
3/16
7/32
1/4
5/16
3/8
3/8
1-1/4”
1-5/8
1-7/8
2-1/8
2-5/8
3
6
3-1/2”
3-7/8
4-3/8
5-1/2
6-3/4
7-3/4
10
4-3/4”
5-1/2
6-1/4
7-3/4
9-3/8
10-1/2
16
LARGE – MEDIUM – SMALL
S-HOOKS
HEAVY OPEN STYLE – LIGHT OPEN STYLE
– LIGHT CLOSED STYLE
ROPE BINDING HOOKS
EYE-HOOK
Catalog
Number
Model
No.
Thread
Size
Take
Up
Length
Closed
Length
Open
21
22
23
24
25
26
27
11400
11401
11402
11403
11404
11405
11406
5/32
3/16
7/32
1/4
5/16
3/8
3/8
1-1/4”
1-5/8
1-7/8
2-1/8
2-5/8
3
6
3-1/2”
3-7/8
4-3/8
5-1/2
6-3/4
7-3/4
10
4-3/4”
5-1/2
6-1/4
7-3/4
9-3/8
10-1/2
16
ANCHORING
Ph: 215-244-1545
Fx: 215-244-1082
POWER TOOLS
& ACCESSORIES
Ph: 631-234-0740
Fx: 631-234-0686
CONTRACTOR
SUPPLY
Ph: 914-777-3245
Fx: 914-777-3875
DRYWALL SUPPLY
& HAND TOOLS
BENSALEM
Long Island
ADHESIVES
& SEALANTS
ISLANDIA
New York
HEAVY OPEN STYLE
GATE HOOKS AND EYES
WELDED EYE BOLTS
AIR & GAS
NAILERS
MAMARONECK
Model
No.
Thread
Size
Take
Up
Length
Closed
Length
Open
31
32
33
34
35
36
37
11431
11432
11433
11434
11435
11436
11437
5/32
3/16
7/32
1/4
5/6
3/8
3/8
1-1/4”
1-5/8
1-7/8
2-1/8
2-5/8
3
6
3-1/2”
3-7/8
4-3/8
5-1/2
6-3/4
7-3/4
10
4-3/4”
5-1/2
6-1/4
7-3/4
9-3/8
10-1/2
16
U-BOLTS
FASTENERS
HOOK-HOOK
Catalog
Number
285
KASS
Headquarters
BRONX, NEW YORK
Ph: 718-299-6060 • Fx: 718-299-1593
Toll Free: 800-255-0910
INDUSTRIAL SUPPLY CORP.
ANCHORING
ACOUSTICAL
LAG SCREWS & DRIVER
FASTENERS
THREADED ROD
SIZES FROM 1/4 INCH TO 1-1/4 INCHES
AVAILABLE IN EITHER PLAIN OR ZINC PLATED
Flattened and Pierced Ends for Suspended Ceilings
Bolts Gimlet Pointed - Bright Basic Wire - Plated
POWER TOOLS
& ACCESSORIES
Cat. No.
STOCK SIZES
Screw Size and Length
750-0
750-4
750-5
750-1
1/4” x 6 ft.
5/16” x 6 ft.
3/8” x 6 ft.
1/2” x 6 ft.
5/8” x 6 ft.
3/4” x 6 ft.
7/8” x 6 ft.
1” x 6 ft.
1/4 x 3”
1/4 x 4”
1/4 x 5”
5/16 x 3-1/2*
NO. SD-800
CONTRACTOR
SUPPLY
SD-800-Fits 1/4” Screw
SD-751-Fits 5/16” Screw
ANCHOR IT
*5/16” lag screws will accommodate 1/4” steel rod
DRYWALL SUPPLY
& HAND TOOLS
BEAM
CLAMPS
MATERIAL: Carbon Steel
FINISH: Black or Electro-Galvanized
ADHESIVES
& SEALANTS
AIR & GAS
NAILERS
FASTENERS
286
SERVICE: For attachment to I-Beams
and wide flange beams where thickness does not exceed .75 inches.
Flange thickness may not exceed
.62 inches when clamp is used with
retaining strap.
HANG IT
Fig.
#
C-Clamp
Size
(B)
Max. Rec.
Load, Lb.
C
21
Standard
3/8
400
2-3/8
21
Standard
1/2
500
2-3/8 2-5/16 3/4
21
Standard
5/8
550
2-3/8 2-5/16 3/4
21
Standard
3/4
630
2-3/8
2-1/4 1/4
21
Standard
7/8
1200
2-3/4
2-5/8 3/4
D
F
2-3/8 3/4
COUPLE IT
No matter what you Need,
we deliver the FaSteSt
FASTENERS
you’ll ever get!
BOLTS
All hex cap screws are fully threaded
DIAMETER
1/4-20
5/16-18
3/8”-16
1/2-13
5/8-11
3/4-10
&
FASTENERS
HIGH STRENGTH
STRUCTURAL BOLTS
ASTM A325 TYPE 1
HEAVY HEX HEAD
LENGTH
1” to 3”
1” to 3”
1/-1/4” to 6”
1-1/2” to 6”
1-3/4” to 4”
2” to 4”
Material
Medium
Carbon Steel
Quenched
& Tempered
SQUARE HEAD MACHINE BOLTS
DIAMETER
1/4-20
5/16-18
3/8”-16
1/2-13
5/8-11
3/4-10
7/8-9
1-8
1-1/8-7
1-1/4-7
&
3/4” to 6”
3/4” to 6”
3/4” to 12”
1” to 20”
1” to 16”
1-1/4” to 18”
1-1/2” to 16”
2” to 16”
4” to 8”
4” to 8”
Material
Alloy Steel
Quenched
& Tempered
Proof Load
(psi)
1/2 thru 1
1-1/8 thru 1-1/2
85,000
74,000
Mechanical Properties
Yield Strength
Tensile Strength
Min. (psi)
Min. (psi)
92,000
81,000
120,000
105,000
Nominal Size
Range (in)
Proof Load
(psi)
1/2 thru 1-1/2
120,000
Mechanical Properties
Yield Strength
Tensile Strength
Min. (psi)
Min. (psi)
130,000
150,000
170,000
ALLOY-STEEL &
STAINLESS STEEL BOLTING
High-Temperature and Low-Temperature Service
OTHER BOLTS
THE LARGEST STOCK IN THE EAST!
For special
thread lengths
or
diameters,
Call the
SuPPlier with
the
largeSt StoCK!
ANCHOR BOLTS
PLOW BOLTS
STEP BOLTS
ELEVATOR BOLTS
STOVE BOLTS
CARRIAGE BOLTS
Nominal Size
Range (in)
ASTM A490 TYPE 1
HEAVY HEX HEAD
LENGTH
We have the items shown IN STOCK
The sizes that are not in stock
we can order and deliver FAST
We also have other tap bolts in stock
plus hard to find square head bolts
If we can’t fill special requirements
from stock, we’ll have them made
and shipped to you as quickly as possible.
ANCHORING
HEX HEAD TAP BOLTS
Pennsylvania
Ferritic steel stud bolt for use in high
temperature service (-50° to 1000°F).
Used in high temperature, hi pressure
applications. (50° to 1100°F).
For use in low temperature service from -50°
max, without charpy impact testing. Charpy
impact testing for -150°F service requires a
minimum average of 20 Ft/Lb. for the required 3 test at test temperature.
Both grades of austenitic steel studs are for use in corrosive environments
with temperature ranges of -325°F to 1500°F.
A193 Grade B7, B7M - Chromium-Molybdenum (AISI 4140, 4142,4145)
A193 Grade B16 - Chromium-Molybdenum-Vanadium (AISI 4140-V,
4142-V,4145-V)
A320 Grade L7 - Chromium-Molybdenum (AISI 4140, 4142,4145)
A193 Grade B8 - Chromium-Nickel-Molybdenum (AISI 316)
Min.
Tempering
Temp. F
Tensile
Strength
Min. psi
(000)
Yield
Point
Min. psi
(000)
105
95
Hardness
Grade
Diameter in.
A193 Grade B7
2-1/2 and under
Over 2-1/2 to 4 in.
1100
1100
125
115
A193 Grade B7M
2-1/2 and under
1150
100
80
201-235
A193 Grade B16
2-1/2 and under
1200
125
Over 2-1/2 to 4 in.1200
105
110
95
A320 Grade L7
2-1/2 and under
—
105
A193 Grade B8
All diameters
—
75
30
A193 Grade B8
(Class 2)
Strain-hardened
1/4 and under
Over 1/4 thru 1
Over 1 thru 1-1/4
Over 1-1/4 thru 1-1/2
—
—
—
—
125
115
95
100
100
90
65
50
A193 Grade B8M
(Class 2)
Strain-hardened
1/4 and under
Over 1/4 thru 1
Over 1 thru 1-1/4
Over 1-1/4 thru 1-1/2
—
—
—
—
110
100
95
90
95
80
65
50
125
POWER TOOLS
& ACCESSORIES
Ph: 215-244-1545
Fx: 215-244-1082
CONTRACTOR
SUPPLY
Ph: 631-234-0740
Fx: 631-234-0686
DRYWALL SUPPLY
& HAND TOOLS
Ph: 914-777-3245
Fx: 914-777-3875
ADHESIVES
& SEALANTS
BENSALEM
Long Island
Brinall
320 max
330 max
AIR & GAS
NAILERS
ISLANDIA
New York
FASTENERS
MAMARONECK
287
KASS
Headquarters
BRONX, NEW YORK
Ph: 718-299-6060 • Fx: 718-299-1593
Toll Free: 800-255-0910
INDUSTRIAL SUPPLY CORP.
ANCHORING
SELF TAPPING SCREWS - NUTS & WASHERS
HEAVY HEX NUTS
TAPPING SCREWS
SUITABLE NUTS FOR A325 & A490 STRUCTURAL BOLTS
Available from stock Plain Finish and Hot Galvanized
PHILLIPS PAN HEAD TYPE A-AB
SELF TAPPING SCREWS
Steel • Zinc Plated
DIAMETER
POWER TOOLS
& ACCESSORIES
CONTRACTOR
SUPPLY
DRYWALL SUPPLY
& HAND TOOLS
ADHESIVES
& SEALANTS
AIR & GAS
NAILERS
FASTENERS
288
Length
4
6
1/4
3/8
1/2
5/8
3/4
1
1-1/4
1-1/2
1-3/4
2
2-1/2
3
X
X
X
X
X
X
X
X
X
X
X
X
X
8
10
12
14
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
PHILLIPS FLAT HEAD TYPE A-AB
SELF TAPPING SCREWS
Steel • Zinc Plated
DIAMETER
Length
4
6
1/4
3/8
1/2
5/8
3/4
1
1-1/4
1-1/2
1-3/4
2
2-1/2
3
X
X
X
X
X
X
X
X
X
X
X
X
X
8
10
12
14
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
FLAT STEEL
Plain and Zinc Plated - U.S. Standard
Bolt
Size
I.D.
(Inches)
A
O.D.
(Inches)
B
Approx.
No. In.
100 Lbs.
3/16
1/4
5/16
3/8
7/16
1/2
9/16
5/8
3/4
7/8
1
1-1/8
1-1/4
1/4
5/16
3/8
7/16
1/2
9/16
5/8
11/16
13/16
15/16
1-1/16
1-1/4
1-3/8
9/16
3/4
7/8
1
1-1/4
1-3/8
1-1/2
1-3/4
2
2-1/4
2-1/2
2-3/4
3
36,200
14,900
9,000
6,700
4,100
2,600
2,200
1,300
910
650
530
450
380
Bolt
Size
I.D.
(Inches)
A
O.D.
(Inches)
B
Approx.
No. In.
100 Lbs.
6 (1/8)
8 (5/32)
10 (3/16)
12 (7/32)
5/32
3/16
7/32
1/4
3/8
7/16
1/2
9/16
79,000
58,500
43,500
36,200
S.A.E. Standard
(A 325)
ASTM A 563
GRADE C
FOR: A 325
BOLTS
THESE NUTS ARE ALSO
AVAILABLE IN ”2H” FOR
USE WITH A490 BOLTS
THESE NUTS ARE PACKED WITH
A325 BOLTS IN FULL KFGS
A325
Bolts
Proof1
Load
Nominal
Thds Per
Inch and
Thread
Series
1/2-13 UNC
5/8-11 UNC
3/4-10 UNC
7/8- 9 UNC
1- 8 UNC
1-1/8 -7 UNC
1-1/8- 8 UN
1-1/4- 7 UNC
1-1/4- 8 UN
1-3/8- 6 UNC
1-3/8- 8 UN
1-1/2- 6 UNC
1-1/2- 8 UN
(A 325)
ASTM A 563
GRADE C AND SELFLOCKING NUTS FOR:
A 325 BOLTS
ASTM A 194
GRADE 2
FOR: A 325
BOLTS
ASTM A 194
FOR: A 325
BOLTS &
A 490 BOLTS
A490
Bolts
Proof1
Load
lb
A325
Bolts
Tensile2
Strength
Min
lb
A325
Nuts
Proof3
Load
lb
A490
Bolts
Tensile2
Strength
Min
lb
12,050
19,200
28,400
39,250
51,500
56,450
58,450
71,700
74,000
85,450
91,250
104,000
110,400
17,050
27,100
40,100
55,450
72,700
80,100
82,950
101,700
105,000
121,300
129,500
147,500
156,700
A194
Nut
Proof3
Load
lb
lb
17,050
27,100
40,100
55,450
72,700
91,550
94,800
110,300
120,000
138,600
148,000
160,800
175,050
21,300
33,900
50,100
69,100
90,900
114,450
118,500
145,350
150,000
173,750
185,000
210,750
223,800
20,450
32,550
40,100
66,550
87,250
109,900
113,800
139,500
144,000
166,300
177,600
202,300
214,800
24,850
39,550
58,450
80,850
106,000
133,500
138,200
169,600
175,000
707,100
215,800
745,900
261,100
NOTES: 1 Proof load of bolt is the load the bolt must support in axial tension without
permanent deformation
2 Tensile strength of bolt is the minimum load the bolt must support in
axial tension without failure of the bolt
3 Proof load of nut is the load the nut must support axially without evidence of
thread stripping or rupture
WASHERS
FENDER
Bolt
Size
I.D.
(Inches)
O.D.
(Inches)-
Bolt
Size
I.D.
(Inches)
O.D.
(Inches)
3/16
3/16
1/4
1/4
1/4
1/4
1/4
7/32
7/32
9/32
17/64
9/32
5/16
9/32
1-1/8
1-1/4
1
1-1/8
1-1/4
1-1/4
1-1/2
5/16
5/16
5/16
3/8
3/8
1/2
1/2
3/8
11/32
11/32
25/64
17/32
17/32
17/32
1-1/4
1-1/4
1-1/2
1-1/2
1-1/2
1-1/2
2
HELICAL SPRING LOCK WASHERS
Nominal Washer
Size
1/4
5/16
3/8
7/16
1/2
9/16
5/8
11/16
3/4
13/16
7/8
15/16
0.256
0.312
0.375
0.438
0.500
0.562
0.625
0.688
0.750
0.812
0.875
0.938
Inside Diameter
Min.
Max
0.255
0.318
0.382
0.446
0.509
0.572
0.636
0.700
0.763
0.826
0.875
0.954
0.263
0.328
0.393
0.459
0.523
0.587
0.653
0.718
0.783
0.847
0.890
0.978
(SPLIT LOCKWASHERS)
REGULAR
(MEDIUM)
Pennsylvania
SCREWS
MACHINE SCREWS
SOCKET SCREWS
SLOTTED
available in lengths 1/8” to 6” and diameters #0 to 3/8”
FLAT
ROUND
BINDING
TRUSS
SLOTTED
INDENTED
HEX
UNSLOTTED
FILLESTER
PAN
OVAL
available in steel, stainless, brass,
bronze, monel, nylon, and other materials
PHILLIPS
ROUND
SOCKET HEAD
CAP SCREWS
Available in alloy & stainless
steel. Sizes #0-1-1/2” diameter. Standards and specials
in stock.
PHILLIPS
BINDING
HEX KEYS AND KEY SETS
Heat treated alloy steel.
.028 to 1-1/2” hex.
Long and short arm series.
SQUARE HEAD
SET SCREWS
Case hard carbon steel.
1/4” dia. Forgings to 1/4”
dia. Other metals available.
PRECISION
DOWEL PINS
Alloy and stainless.
1/16” to 1” dia.
We have most standard sizes
and materials in stock as well
as many special sizes and materials.
Call us for
custom sizes in hard to find materials.
SOCKET FLAT HEAD
CAP SCREWS
Available in alloy and stainless. #0 to 3/4” dia.
FILLISTER
PAN
OVAL
GRADE
2
1” thru 6”
1-1/4” thru 5”
1-1/2” thru 7”
Min. Tensile Strength
Proof Load
2
SAE J429
ASTM A307,
GR. A& B
60,000 PSI
36,000 PSI
SAE J429
ASTM A449
1/4” to 1” dia:
120,000 PSI
over 1” to 1-1/2”
105,000 PSI
1/4” to 1” dia. 85,000 PSI
over 1” to 1-1/2” 74,000 PSI
over 1-1/2” to 3” 55,000 PSI
SAE J429
ASTM 435A
GR.BD
150,000 PSI
129,000 PSI
5
7/8-9
1-8
TYPE
S
8
Lengths
2” thru 4-1/2”
2” thru 6”
THUMB SCREWS
TYPE
P
SPECIAL SCREWS
NATIONAL COARSE THREAD
ROUND & FLAT
Slotted Spanner
ROUND
One Way
Grade 2
Grade 2
Grade 5
Grade 8
1/4-28
1/4-20
1/2” to 8”
3/8” to 8”
1/2” to 8”
5/16-24
5/16-18
3/8” to 8”
3/8” to 8”
1/2” to 8”
3/8-24
3/6-16
1/2” to 12”
1/2” to 10”
1/2” to 8”
7/16-20
7/16-14
3/4” to 6”
3/4” to 10”
3/4” to 8”
1/2-20
1/2-13
1/2” to 24”
1/2” to 15”
3/4” to 15”
9/16-18
9/16-12
—
1” to 6”
1” to 6”
5/8-18
5/8-11
1” to 24”
1” to 15”
1” to 15”
3/4-16
3/4-10
1” to 24”
1” to 15”
1” to 15”
7/8-14
7/8-9
1-1/4” to 24”
1” to 12”
1-1/2” to 12”
1-14
2” to 12”
1-1/8-12
1-8
ROUND & FLAT
Drilled Spanner
GRADE
8
Specifications
LOW CARBON STEEL
Available only in plain finish National coarse threads
Diameter
GRADE
5
Grade
SLOTTED FLAT HEAD CAP SCREWS
Lengths
DRYWALL SUPPLY
& HAND TOOLS
HEX HEAD CAP SCREWS
TRUSS
1/2-13
5/8-11
3/4-10
SOCKET
PRESSURE PLUGS
Steel, stainless, brass
1/16” to 1-1/4” pipe threads
Dryseal, flush in most sizes
SOCKET
SET SCREWS
Alloy and stainless.
#0 to 1” dia.
In many sizes and styles.
PHILLIPS
Diameter
SOCKET HEAD
SHOULDER SCREWS
Alloy, stainless and specials.
1/4” to 3/4”.
SOCKET BUTTON
HEAD CAP SCREWS
In alloy and stainless
#0 to 5/8” dia.
INDENTED HEX
WASHER
SLOTTED
PhilliPS
PHILLIPS
FLAT
FASTENERS
1-1/2” to 24” 1-1/2” to 15”
N
O
T
A
V
A
I
L
A
B
L
E
Grade 5
Grade 8
1/2” to 8”
1/2” to 6”
1/2” to 6”
1/2” to 6”
1/2” to 8”
1/2” to 6”
3/4” to 6”
3/4” to 6”
3/4” to 15”
3/4” to 15”
1” to 6”
1-1/4” to 6”
1” to 15”
1” to 15”
1” to 15”
1” to 15”
1-1/2” to 10” 2-1/2” to 10”
2” to 10”
2” to 10”
3” to 10”
2-1/2” to 15”
1-1/8-7
2” to 16”
2” to 12”
2-1/2” to 16” 1-1/4-12
USE
3” to 12”
2-1/2” to 16”
1-1/4-7
2-1/2” to 24”
2” to 13”
2-1/2” to 16” 1-3/8-12
G
R
A
D
E
—
3-1/2” to 16”
1-3/8-6
—
—
3” to 16”
1-1/2-12
1-1/2-6
3” to 16”
3” to 12”
4” to 16”
1-3/4-12
1-3/4-5
5” to 16”
5” to 8”
4” to 16”
2-12
2-4-1/2
8” to 16”
—
4” to 16”
NATIONAL FINE THREAD
ANCHORING
Ph: 215-244-1545
Fx: 215-244-1082
POWER TOOLS
& ACCESSORIES
Ph: 631-234-0740
Fx: 631-234-0686
CONTRACTOR
SUPPLY
Ph: 914-777-3245
Fx: 914-777-3875
ADHESIVES
& SEALANTS
BENSALEM
Long Island
AIR & GAS
NAILERS
ISLANDIA
New York
3” to 16”
3” to 16”
—
4” to 16”
—
4” to 16”
5 OR 8
NOT LISTED?
CALL US - IT MAY BE IN STOCK or WE CAN ORDER IT FOR YOU!
FASTENERS
MAMARONECK
289
KASS
Headquarters
INDUSTRIAL SUPPLY CORP.
BRONX, NEW YORK
Ph: 718-299-6060 • Fx: 718-299-1593
Toll Free: 800-255-0910
ANCHORING
TRI-LOK SELF DRILLING SCREWS
JD’s fast drilling point is designed to prevent
walking for quick penetration into 14-20 gauge steel.
Important in one-handapplications from difficult positions.
JD - BUGLE HEAD
Cat.
No.
Size
(Inches)
Approx.
Gross Weight
Quantity
(Thousands)
POWER TOOLS
& ACCESSORIES
JD100
#6 x 1
37 lbs.
10
JD118
#6 x 1-1/8
39 lbs.
10
JD114
#6 x 1-1/4
35 lbs.
8
JD158
#6 x 1-5/8
25 lbs.
5
JD178
#6 x 1-7/8
22 lbs.
4
JD238
#8 x 2-3/8
24 lbs.
3
JD258
#8 x 2-5/8
16 lbs.
2
JD300
#8 x 3
18 lbs.
2
Bugle head self-drilling screw to attach gypsum, wood, etc. to 14-20 gauge steel stud.
PJD - FRAMING HEAD
Cat.
No.
PJD716
Size
(Inches)
#7 x 7/16
Approx.
Gross Weight
Quantity
(Thousands)
49 lbs.
15
For framing and attaching fixtures and door frames, etc. 14-20 gauge steel.
SELF TAPPING SCREWS
CONTRACTOR
SUPPLY
RECESS - Deep, cleanly formed, and specially designed for positive hold to
prevent binding to #2 Phillips Bit from any position.
THREADS - Clean, without chips to prevent burring of paper. Double lead
tapping threads are designed to give maximum holding power.
POINT - Patented cutting thread for maximum penetration speed without
screw hesitation, thereby reducing operator fatigue.
TL - BUGLE HEAD
Cat.
No.
DRYWALL SUPPLY
& HAND TOOLS
TL - FRAMING HEAD
Cat.
No.
Size
(Inches)
Quantity
(Thousands)
TL716
#7 x 7/16
42 lbs.
15
Framing screws for 20-25 gauge. Low profile with deep recess. Special
serrations under head prevent spin-out.
Approx.
Gross Weight
Quantity
(Thousands)
TL100
#6 x 1
37 lbs.
10
TL118
#6 x 1-1/8
39 lbs.
10
TL114
#6 x 1-1/4
26 lbs.
8
TL158
#6 x 1-5/8
28 lbs.
5
TL200
#6 x 2
20 lbs.
3.5
TL214
#6 x 2-1/4
19 lbs.
3
TL212
#7 x 2-1/2
21 lbs.
2.5
TL300
#8 x 3
17 lbs.
2
For fastening gypsum to 20-25 gauge steel stud. Hi-speed with excellent holding power!
ADHESIVES
& SEALANTS
DRYWALL SCREWDRIVERS
DW252
AIR & GAS
NAILERS
FASTENERS
290
Approx.
Gross Weight
Size
(Inches)
6.0 AMP; 0-4,000 RPM
DW272
6.3 AMP; 0-5,300 RPM
BOTH MODELS FEATURE
• Depth-sensitive “set and forget”
nosepiece for consistent fastener
depth
• Metal gear housing for increased
durability
• Rubber grip and two-finger trigger
for increased comfort
• Helical-cut steel, heat treated
gears for long life and durability
NEW
FS4200
• 6.0 AMP motor with 0-4,000
RPM
• Lightest drywall gun in its class
at only 2.9 lbs.
• Large variable speed trigger
with lock-on button
• L.E.D. light illuminates the work
surface
• Consistent screw depth with
Sure-Lock° adjustable depth
locator assembly
• Convenient bit storage on base
of grip reduces downtime
• Metal reinforced belt clip for
increased durability
• Includes: #2 phillips insert bit
and magnetic bit holder
6742-20
• 6.5 AMP motor
• Ramp-off depth locator
• All ball and roller bearings
• 10’ 2-wire rubber cord
• Quiet snap-action clutch
• Modular brush card design
• All metal gear case and
diaphragm
Pennsylvania
TITE ROCK ™ DRYWALL SCREWS
LEADERS
DRYWALL SCREWS SHARP POINT
BUGLE HEAD TYPE-S
Attaches gypsum board to 20-25 ga. steel. Standard bugle head.
No. 2 Phillips recess.
PART NO.
EZ100
EZ118
EZ114
EZ158
EZ200
EZ214
EZ212
EZ300
SIZE
QTY/CTN
WT/CTN
6 x 1”
6 x 1-1/8”
6 x 1-1/4”
6 x 1-5/8”
6 x 2”
6 x 2-1/4”
8 x 2-1/2”
8 x 3”
10m
10m
8m
5m
3.5m
3m
2.5m
2m
37
41
36
30
23
21
24
26
PHILLIPS PAN HEAD
TYPE-S
SIZE
EZPST716
7 x 7/16”
SELF DRILLING CONSTRUCTION SCREWS
BUGLE HEAD SELF-DRILL
Attaches gypsum board, insulation board, wood, etc. to metal studs.
PART NO.
DO100
DO114
DO158
DO178
DO238
DO258
DO300
SIZE
QTY/CTN
WT/CTN
6 x 1”
6 x 1-1/4”
6 x 1-5/8”
6 x 1-7/8”
8 x 2-3/8”
8 x 2-5/8”
8 x 3”
10m
8m
5m
4m
3m
2m
2m
38
30
27
25
28
23
26
PHILLIPS PAN HEAD FRAMING SELF-DRILL
PART NO.
SIZE
WT/CTN
15m
35
WAFER HEAD TYPE-S
PART NO.
SIZE
QTY/CTN
WT/CTN
EZWST916
EZWST100
EZWST114
8 x 9/16”
8 x 1”
8 x 1-1/4”
10m
5m
5m
42
27
32
TRIM HEAD TYPE-S - SQUARE & PHILLIPS DRIVE
Attaches wood trim over single or double-layer gypsum
board to 20-25 ga. steel.
PART NO.
SIZE
QTY/CTN
WT/CTN
EZST158
EZST214
EZST300
6 x 1-5/8”
6 x 2-1/4”
8 x 3”
8m
4m
2m
36
27
PART NO.
For attachment to gypsum board to wood, with superior holding power and ease
of penetration. No. 2 Phillips recess.
SIZE
QTY/CTN
WT/CTN
6 x 1”
6 x 1-1/8”
6 x 1-1/4”
6 x 1-5/8”
6 x 2”
6 x 2-1/4”
8 x 2-1/2”
8 x 3”
10m
10m
8m
5m
3.5m
3m
2.5m
2m
37
40
36
30
23
24
26
25
For temporary fastening of gypsum in laminated
drywall construction. No. 2 Phillips recess.
SIZE
EZ112
10 x 1-1/2”
QTY/CTN
WT/CTN
5m
36
SIZE
EZA278
EZA334
11 x 2-7/8”
11 x 3-3/4”
8 x 1/2”
8 x 5/8”
8 x 3/4”
8 x 1”
10 x 1/2”
10 x 5/8”
10 x 3/4”
10 x 1”
10 x 1-1/4”
10 x 1-1/2”
10 x 1-3/4”
10 x 2”
12 x 3/4”
12 x 1”
12 x 1-1/2”
12 x 2”
12 x 2-1/2”
QTY/CTN
WT/CTN
10m
10m
10m
7.5m
10m
7.5m
5m
5m
3.5m
3.5m
3m
2m
5m
3.5m
2.5m
2m
12m
36
41
46
40
50
45
31
38
31
35
33
25
43
35
33
34
38
Attaches fixtures,
backup plates,
door frames and
lathers channel to
structural studs,
metal decks, etc.,
14-20 ga.
6 & 8 ga. screws,
use 1/4” nut setter.
10 & 12 ga.
screws, use 5/16”
nut setter.
14 ga. screws, use
3/8” nut setter.
PHILLIPS
PAN HEAD SELF-DRILL
PART NO.
DPP62012FSZ
DPP62034FSZ
DPP81812FSZ
DPP818134FSZ
DPP8181FSZ
DPP101612FSZ
DPP101634FSZ
DPP10161FSZ
DPP1016112FSZ
SIZE
6 x 1/2”
8 x 3/4”
8 x 1/2”
8 x 3/4”
8 x 1”
10 x 1/2”
10 x 3/4”
10 x 1”
10 x 1-1/2”
QTY/CTN
WT/CTN
15m
10m
10m
10m
7.5m
10m
7.5m
5m
2m
32
31
34
44
38
48
45
36
36
WAFER HEAD SELF-DRILL
PART NO.
SIZE
QTY/CTN
WT/CTN
DOW012
DOW114
8 x 1/2”
8 x 1-1/4”
10m
5m
36
35
OVAL HEAD CABINET SCREW
For cabinet assembly and installation. No. 2 Phillips recess.
PART NO.
45
Attaches
fixtures,
backup plates,
door frames,
plaster grounds,
etc., 14-20 ga.
No. 2 Phillips
recess.
Attaches metal K-lath, wire lath, wood grounds, etc., to lathers channel structural studs, metal decks, etc. Also used for attachment of steel
studs to runners, 14-20 ga. No. 2 Phillips recess.
LAMINATING SCREW
PART NO.
WT/CTN
15m
SIZE
DHH81812FSZ
DHH81858FSZ
DHH81834FSZ
DHH8181FSZ
DHH101612FSZ
DHH101658FSZ
DHH101634FSZ
DHH10161FSZ
DHH1016114FSZ
DHH1016112FSZ
DHH1016134FSZ
DHH10162FSZ
DHH121434FSZ
DHH12141FSZ
DHH1214112FSZ
DHH12142FSZ
DHH1214212FSZ
BUGLE HEAD HI THREAD
EZC100
EZC118
EZC114
EZC158
EZC200
EZC214
EZC212
EZC300
QTY/CTN
7 x 7/16” Pan
HEX WASHER HEAD SELF-DRILL
QTY/CTN
For attaching metal lathe to 20-25 ga. steel studs and
framing. No. 2 Phillips recess.
PART NO.
14-20 ga.
No. 2 Phillips recess
Stud to track - pan head has new flat head design for better recess fit.
DO716
Framing screws for 20-25 ga. Unique grip tight, high
torque pan head. No. 2 Phillips recess.
PART NO.
DUO-DRILLS
QTY/CTN
WT/CTN
2m
1m
30
20
TRIM HEAD SELF-DRILL
Attaches wood trim over single or double-layer gypsum
board to 20-25 ga. steel. No. 1 Phillips recess.
PART NO.
SIZE
QTY/CTN
WT/CTN
JDST158
JDST214
6 x 1-5/8”
6 x 2-1/4”
5m
3m
25
21
ANCHORING
FASTENERS
POWER TOOLS
& ACCESSORIES
Ph: 215-244-1545
Fx: 215-244-1082
CONTRACTOR
SUPPLY
Ph: 631-234-0740
Fx: 631-234-0686
DRYWALL SUPPLY
& HAND TOOLS
Ph: 914-777-3245
Fx: 914-777-3875
ADHESIVES
& SEALANTS
BENSALEM
Long Island
AIR & GAS
NAILERS
ISLANDIA
New York
FASTENERS
MAMARONECK
291
KASS
Headquarters
BRONX, NEW YORK
Ph: 718-299-6060 • Fx: 718-299-1593
Toll Free: 800-255-0910
INDUSTRIAL SUPPLY CORP.
ANCHORING
NAILS & STAPLES
BRIGHT COMMON NAILS
3D (1-1/4”)
7D (2-1/4”)
12D (3-1/4”)
30D (4-1/2”)
60D (6”)
4D (1-1/2”)
8D (2-1/2”)
16D (3-1/2”)
40D (5”)
6D (2”)
10D (3”)
20D (4”)
50D (5-1/2”)
POWER TOOLS
& ACCESSORIES
BRIGHT FINISHING NAILS
3D (1-1/4”)
8D (2-1/2”)
4D (1-1/2”)
10D (3”)
6D (2”)
16D (3-1/2”)
KOLORPINS® STYLE “A”
PLAIN SHANK
WHITE
Cat.
No.
Length
Gauge
Head
Nails
Per Lb.
114KLR
1-1/4”
15
.114
754
These slender, hardened steel nails are used to apply interior
wall coverings made of hardboard, particleboard or woodbacked materials. The button head is inconspicuous when
driven flush. Color.: White
MANSONRY NAILS
(Hardened)
BRIGHT DUPLEX SCAFFOLD NAILS
CONTRACTOR
SUPPLY
6D (2”)
16D (3-1/2”)
8D (2-1/2”)
20D (3-1/2”)
10D (3”)
GALVANIZED
FENCE
STAPLES
DRYWALL SUPPLY
& HAND TOOLS
1-1/4 - 1-1/2
HARDENED CUT FURRING (Masonry) NAILS
3D (1-1/4”)
5D (1-3/4”)
8D (2-1/2”)
12D (3-1/4”)
4D (1-1/2”)
6D (2”)
9D (2-3/4”)
16D (3-1/2”)
4-1/2D (1-5/8”)
7D (2-1/4”)
10D (3”)
20D (4”)
MADE IN U.S.A.
5/8”
1-3/4”
3”
3/4”
1-1/2”
3/4”
2”
3-1/2”
1”
2-1/4”
4”
ROOFING
NAILS,
GALVANIZED
7/8”
1-3/4”
1”
2”
1-1/2”
2-1/2”
1-1/4”
2-1/2”
DRYWALL NAILS
RING BARD®
1-1/4”
1-3/8”
1-1/2”
1-5/8”
1-7/8”
ADHESIVES
& SEALANTS
KLIK-FAST®
COMPLETE LOW PROFILE BLIND RIVETING SYSTEM
AIR & GAS
NAILERS
FASTENERS
292
• Strong, positive assembly, neat
appearance.
• Quick and easy installation – low in
place cost.
• Vibration and tamper resistant.
• Does not mar work surfaces.
• Quickly set by one person from one side
of assembly.
• Fasten metal to metal, wood and
plastics to metal, all materials to
fiberglass, and most other materials.
• Available in steel, aluminum, stainless
steel and copper.
• Available in button head, countersunk,
and large flange.
• AVAILABLE IN WHITE
3”
2”
KASS
INDUSTRIAL SUPPLY CORP.
CONSTRUCTION PRODUCTS
“The Professional’s Choice”
Grabber has the fasteners you need to do the job
INTERIOR WOOD Drywall
Bugle head
Coarse thread
Laminating
HEAVY GAUGE METAL Drywall
Streaker®
Bugle head
Trim head
HEAVY GAUGE METAL Framing
LIGHT GAUGE METAL Drywall
Streaker®
Bugle head
Fine thread
Trim head
Framing
EXTERIOR WOOD General
Particle board
Square drive flat head deep thread
Type 17pt Woody’s
EXTERIOR WOOD Deck Fastening
GrabberGuard® (exterior grade)
305 stainless
316 stainless (marine grade)
Composite deck screws
Collated LOX® drive
Collated deck screws
www.kassind.com
Metal to wood (XtekTM)
Hex washer head self drill
Hex washer head self drill
W/bonded washer (GrabberGard)
Pan head Philips self drill
410 stainless self drill screws
Flat phil. Self Drill
Plymetal
Plymetal w/wings
Reemer self drill
Hex head self drill #4 & #5 point
Stainless steel self drill
Flat head
Hex head
Pan head.
Stitch screws
Dekfast roofing screws
Roofing screws (SFS) w/plates
Clip screws
Zacs
CEMENT BOARD Sheathing
K-lath
Cement board
293
KASS
INDUSTRIAL SUPPLY CORP.
CONSTRUCTION PRODUCTS
“The Professional’s Choice”
SIZE
Bugle Head Streaker
®
Attaches gypsum board to 20-25
ga. steel. Standard bugle head.
No. 2 Phillips recess
COMMERCIAL
CTN PART NO. &
QTY.
1 LB. CTN.
PART NO.
5 LB. CTN.
PART NO.
6X1
168S
10M
X168S
V168S
6 X 1-1/8
268S
10M
X268S
V268S
6 X 1-1/4
368S
8M
X368S
V368S
6 X 1-5/8
468S
5M
X468S
V468S
Note:
Some lengths available in Clear Zinc (Z), Yellow Zinc (YZ) and ACQ compliant GrabberGard (RG) finish.
Bugle Head GRABBER® Coarse Thread
Attaches gypsum board
to wood with superior
holding power and ease of
penetration.
No. 2 Phillips recess.
6 X 1-1/8
200
10M
X200
V200
6 X 1-1/4
300
8M
X308
V308
6 X 1-5/8
400
5M
X408
V408
7X2
500
3.5M
X500
V500
7 X 2-1/4
600
3M
X600
V600
8 X 2-1/2
900
2.5M
X900
V900
8X3
1100
2M
X1100
V1100
Note:
Some lengths available in Clear Zinc (Z), Yellow Zinc (YZ) and ACQ compliant
GrabberGard (RG) finish.
Bugle Head Self-Drilling
Attaches gypsum, insulation
board, wood, etc. to metal
studs. 14-20 ga.
No. 2 Phillips recess.
6X1
13SZ
10M
X13Z
V13Z
6 X 1-1/4
14SZ
8M
X14Z
V14Z
6 X 1-5/8
15SZ
5M
X15Z
V15Z
7 X 1-7/8
16SZ
4M
X16Z
V16Z
8 X 2-3/8
30SSZ
3M
X30SZ
V30SZ
8 X 2-5/8
30MSZ
2M
X30MZ
V30MZ
8X3
30LSZ
2M
X30LZ
V30LZ
Note:
Available in Clear Zinc (Z), GrabberGard (RG), and Black Phosphate.
Other sizes available upon request.
Pan Head Self-Drilling
Framing screw for 14-20 ga.
No. 2 Phillips recess.
294
6 X 7/16
19Z
15M
X19Z
V19Z
6 X 7/16
19 (Black)
15M
X19 (Black)
V19 (Black)
8 X 1/2
20Z
15M
X20Z
V20Z
Toll Free to Bronx, New York 800-255-0910
CONSTRUCTION PRODUCTS
KASS
INDUSTRIAL SUPPLY CORP.
“The Professional’s Choice”
www.kassind.com
295
CONSTRUCTION PRODUCTS
KASS
INDUSTRIAL SUPPLY CORP.
“The Professional’s Choice”
296
Toll Free to Bronx, New York 800-255-0910
CONSTRUCTION PRODUCTS
KASS
INDUSTRIAL SUPPLY CORP.
“The Professional’s Choice”
www.kassind.com
297
CONSTRUCTION PRODUCTS
KASS
INDUSTRIAL SUPPLY CORP.
“The Professional’s Choice”
298
Toll Free to Bronx, New York 800-255-0910