1 DOOR MIRROR COVER WITH LED TURN

DOOR MIRROR COVER WITH LED TURN SIGNAL FOR BRZ/86/FR-S
Thank you for purchasing Authentic ChargeSpeed product
Please check that you have all the necessary hardwares from the list below
Please follow this instruction below
Please prepare and use gloves for your protection.
Necessary hardware: Door Mirror Cover LEFT side
Door Mirror Cover RIGHT side
Wire A for driver side DRL & turn signal 3 in 1　195mm
Wire B for right side Foot lamp 2 in 1　195mm
Wire C for passenger DRL & side turn signal 3 in 1　345mm
Wire D for left side Foot lamp 2 in 1　345mm
Spade terminal
Splice terminal
guarantee card
1
1
1
1
1
1
1
8
1
□
□
□
□
□
□
□
□
□
※This is guide for JDM RHD car, LHD car use wire A & D at left side and wire B & C at right side instead of this instruction.
Necessary tools
socket wrench 10mm, a ring wrench 10mm, screw drivers cross slot and straight slot
vinyl tape, handy remover, cable crimper, awl, cutter knife and a wire puller cable tool.
1. Make sure DRL, turn signal and door welcome light.
5. Remove 2 screws from door grip.
Use handy remover from bottom of door grip cover to remove.
2. Disconnect negative terminal from battery.
3. Remove 3 screws at 〇 shown below.
4. Screw at door handle was hidden by round cover.
1
6. Remove clip at 〇 shown below
9. Remove connectors at back side of door lining.
7. Remove door lining panel.
Use handy remover, 10 pins were hidden at 〇 shown below.
10. Remove plastic cover inside of door until half way.
11. Disconnect door mirror connector at ○ shown below.
12. Take picture of door mirror connector so you remember before take off.
This is very important when you reinstall all wires to same location.
Unlock connector as shown below and push terminal by awl to pull out wires.
8. Remove Door lock cable.
2
13. Fold door mirror and take off base cover.
16. Pull mirror from bottom and remove the glass.
14. Remove 3 bolts at 〇 shown below.
17. Remove 3 screws at ○ shown below.
15. Remove rubber at door mirror base and take off 3 bolts at 〇 shown below.
18. Remove bolt at 〇 shown below and take off motor unit.
3
19. Remove vinyl tape at both end of door mirror wire tube.
21. Install motor unit to door mirror cover by 3 bolts at 〇 shown below.
20. Insert all wires from door mirror cover into tube with wire puller cable tool.
Use wire puller cable tool and pull wires about 20mm from tube.
Get vinyl tape back on tube and wires.
22. Reinstall motor unit by bolt at 〇 shown below.
23. Install door mirror cover to door mirror base by 3 bolts at 〇 shown below.
Return rubber to door mirror base.
4
24. Reinstall wiring into door.
25. Reinstall door mirror by 3 bolts at 〇 shown below.
29. Remove door sill cover.
26. Install cover to base of door mirror.
30. Remove clip at 〇 shown below.
27. Reinstall mirror to door mirror unit from top to bottom properly.
28. Return all terminals to connector, refer the picture that took at 12.
Remove cover at shown below.
5
31. Disconnect connector at ○ shown below.
air bag connector
Disconnect connectors for door lock and power window.
34. Reinstall rubber tube and coupler after full wire A & B.
32. Remove rubber tube between door and body, there is coupler at body side.
35. Connect terminals of 3 in 1 DRL and turn signal wire come from
mirror cover to connector of wire A.
Coordinate wire by same color.
36. Connect terminals of 2 in 1 door welcome light wire from mirror cover
to connector of wire B. Coordinate wire by same color.
33. Put terminal side of wire A & B from door side of tube which come in
to rubber. Use wore puller cable tool and pull wires about 200mm from
body side of tube. Connector side of wire A & B is on top.
37. Use wire C & D and work same thing on passenger side.
Pull wire C & D under carpet and center console to driver side.
Wires must not touch to pedals.
6
40. Bring red wire from A for turn signal, red wire from C and blue wire
which connected at 38 to under steering wheel at 〇 shown below.
41. Connect black wire from B and black wire from D by splice terminal.
Connect white wire from B and white wire from D by splice terminal.
Isolate by vinyl tape.
Ref: how to use splice terminal.
38. Connect blue wire from A for DRL and blue wire from C for DRL by splice.
Isolate by vinyl tape.
Ref: how to use splice terminal.
42. Remove side cover of dash board shown below.
39. Connect black wire from A and black wire C by spade terminal and ground
at 〇 shown below. Ref: how to use spade terminal.
43. Remove A pillar cover, remove from top.
7
46. Remove 2 screws at ○ shown below and remove the cover under
steering wheel. Disconnect connectors at back of cover.
44. Dis connect the connector.
Peel open bottom black tube about 50mm.
47. Disconnect connector for turn signal relay.
Connect red wire from C to green wire to connector by splice.
45. Bring black and white wires connected at 41 to bottom of A pillar.
Connect red wire from A to red/blue wire to connector by splice.
Connect black wire from product to blue wire for room lamp by splice terminal
Connect blue wire made at 38 to white/green wire to connector by splice.
Connect white wire from product to orange wire from room lamp by splice terminal. Isolate by vinyl tape, return connector to turn signal relay.
Isolate by vinyl tape, return connector and reinstall to A pillar.
Wires must not touch to pedals.
Ref: how to use splice terminal.
Ref: how to use splice terminal.
8
49. Return vinyl cover inside of door lining which removed at 10.
Fix door lining and return negative connector of battery.
Check and confirm all lighting work properly.
48. Connect connectors at back of cover under steering wheel.
Reinstall cover by 2 screws.
Reinstall side cover of dash board.
9
WIRING DIAGRAM
HOW TO USE SPLICE TERMINAL
HOW TO USE SPADE TERMINAL
1. Remove plastic cover 10mm.
5. Use cable crimper to swage splice terminal.
1. Remove plastic cover 10mm.
2. Remove plastic cover 5mm.
6. Isolate by Vinyl tape.
2. Twist the wires.
3. Twist the wires.
3. Use cable crimper to swage spade terminal properly.
4. Put splice terminal to here
Advance Staff Co., Ltd.
1-13-7 Yuhigaoka Toyonaka Osaka 561-0864 JAPAN
Phone: +81-761-20-2521
10