LitePanel™ Mounting Hardware Instruction Manual • Item

LitePanel Mounting Hardware Instructions • Item: 870571 (LP-SWVLHRDWR)
Socket Head Screws
LitePanel Mounting Hardware
The LitePanel Swivel Mount Hardware is designed to interface the
LitePanel line of frames with the LiteReach® Plus handheld extension
or the appropriate Photoflex LiteStand.
Upper Cover
Lower Track Mount
Allen Wrench
Before assembly check to make sure you have all of the following parts
• 1ea. Swivel Stand Mount
• 1ea. Upper Cover
Swivel Stand
Mount
• 1ea. Lower track mount
• 2ea. 6mm / .75 x 10mm Socket head screws
• 1ea. 3/16”/5mm allen wrench
Attaching the LitePanel Mounting Hardware to LitePanel Frames:
Note: You should have the assembled LitePanel frame lying on a flat
surface
Step 1 Disassemble the upper cover from the lower track mount
using the allen wrench. Figure 1
Note: There are two mounting options for the LitePanel Mounting
Hardware depending on your application:
A. If you are using the hardware with the LiteReach Plus extension
pole then you will only use one LitePanel hardware set. The
orientation of the lower track plate will have the swivel track in a 90
degree position in relation to the frame tube. Figure 2
Figure 1.
Figure 2.
B. If you are using the LitePanel hardware with two light stands to
mount the LitePanel overhead, two LitePanel hardware sets will be
required. The orientation of the lower track plate will have the swivel
track in a parallel position in relation to the frame tube. Figure 3
Note: For most applications it is recommended that you attach the
hardware in the middle of the width of the frame for the best balance
and stability.
Figure 3.
Figure 4.
Step 2 Place the track plate under the frame tube, making sure the
swivel track is in the desired position. Figure 4
Step 3 Place the Top Cover over the frame tube aligning the holes
with the lower Track plate for the attachment screws. Figure 5
Step 4 Attach the top cover to the lower track plate by securely
tightening both socket screws using the Allen wrench. Figure 6
Figure 5.
Figure 6.
For detailed specifications, product tutorial videos and more, please visit www.photoflex.com
Rev 09/2016
Alternatively, the hardware can be attached so that the track plate is
facing out from the edge of the frame. In this configuration, a second
fabric can be attached on the opposite side for a quick change of
reflector surfaces or for double diffusion. Figure 7
Step 5 With either one or two upper and lower components attached
to the frame. Slide the swivel stand mount onto the swivel track on the
lower plate and tighten the set screw knob. Figures 8-9
Figure 7.
Figure 8.
Tip: When using the LitePanels extended like a boom as shown in figure
10, put the swivel handle on your left side when attaching it to the
mounting track. In this way, gravity works with you allowing the weight
of the LitePanel to further tighten the swivel rather than loosen it.
With the Hardware securely attached, it is now ready to be placed on a
Photoflex LiteStand or the LiteReach Plus hand held extension. Figures 10-12
Figure 9.
Figure 10. 39” x 39” LitePanel/
LiteReach Kit
Figure 12. 39” x 39” PVC LitePanel Kit
Customer Support (831) 786-1370
E-mail: [email protected]
Photoflex is a division of PromarkBRANDS, Bartlett, IL USA.
©2016 ALL RIGHTS RESERVED. LiteReach®, Photoflex® and the Photoflex logo are
trademarks or registered trademarks of Photoflex and/or its affiliates in the U.S.
and other countries.
Figure 11. 77” x 77” LitePanel Kit
PHOTOFLEX® WARRANTY
• Warranties only cover manufacturer’s defects and workmanship.
• We reserve the right to inspect all merchandise returned (end users and dealers) for warranty fulfillment.
•
•
•
•
All returns must be pre-approved with Return Manufacturers Authorization obtained from Photoflex/PromarkBRANDS.
A receipt showing date of purchase will be required for all returns.
Freight must be paid by the customer or dealer.
Warranties are valid only from date of Original Purchase.
For detailed specifications, product tutorial videos and more, please visit www.photoflex.com