PDF Instrucitons - The Atlantic Store

Before proceeding please make sure your kit has the following items.
1 x One Arm TV Mount
(two assembly options)
2 x 8.66 in. (220 mm) Velcro Cable Ties
1 x 6 ft. HDMI 3D+Ethernet
1 x 9 ft. HDMI 3D+Ethernet
1 x Cleaning Spray Bottle (6.8 oz.) with
1 x 8 in. Microfiber Cloth
1x 6 Outlet Surge Protector
1
TV Wall Mount
Parts List
Qty
Part #
A
1
F
4
B
1
G
8
C
2
H
1
D
2
Part #
Item
Item
Qty
Parts A and B are pre-assembled at the factory.
Hardware List
Part #
Item
Qty
Part #
Item
Qty
I
M8X16 mm
4
Q
M4/M5 washer
4
J
M6X12 mm
4
R
M6/M8 washer
4
K
M5X12 mm
4
S
M8/M6 spacer
4
L
M4X12 mm
4
T
M4/M5 spacer
4
M
M8X40 mm
4
N
M6X35 mm
4
O
M5X30 mm
4
P
M4X30 mm
4
2
TV Wall Mount
Tools Needed (not included)
Safety Glasses
1/4”or 7 mm
Wood Drill Bit
¼ in or 7 mm
Drill
Stud Finder
Phillips
Screwdriver
3
TV Wall Mount
Assembly Tips:
1. This TV mount is designed for use on a vertical wall that is constructed with wood studs.
2. Become familiar with the instructions and all parts.
3. Make sure that all parts are in the box and in good condition.
4. Assemble the product on the open flat carton or a rug to protect the product and
your floor.
5. Some heavy products need a second person to assist in the assembly. Do not install on a
sloping surface.
Caution:
1. If you do not understand these instructions, or have doubts about the safety of this
installation, contact customer service or call a qualified contractor. The manufacturer is
not liable for damage or injury caused by incorrect mounting, assembly or use.
2. Never let children climb on product or play with product.
3. Do not sit or stand on product.
4. Do not fasten a TV that is heavier than the recommended load rating to the mount.
5. The size and weight of your TV must not exceed 37 to 64 in. (93.98 to 162.56 cm) diagonally or
. (60 kg). The wall must be capable of supporting five times the weight of TV plus the
132 lbs
mount.
6. The mount allows the TV to tilt +5° to -15°.
Minimum distance from wall: 3.07 in. / 78 mm
Maximum distance from wall: 21.65 in. / 550 mm
7. Improper handling can result in cuts and lacerations.
8. Images are for reference only.
4
TV Wall Mount
Step 1
Disassembling parts
A
B
Remove TV mounting plate (B) from wall bracket (A).
Step 2
Installing wall bracket
”
16
mm
6
/40
stud finder
16 in.
40.64cm
A
Fx4
This mount is designed to be attached into wood studs. DO NOT use wall anchors. Seek the assistance of a professional installer to mount your TV without using wood studs.
Using a stud finder, find the center of two studs. With a pencil, mark the two top hole locations
at te desired height making sure you are LEVEL. Hold wall bracket (A) against the wall and
mark the two lower hole locations. Drill four pilot holes at pencil marks 2.5 in. (64 mm) deep,
using a 1/4 in. or 7 mm diameter drill bit. Attach wall bracket (A) to the wall with four washers
and screws (F). DO NOT MOUNT INTO DRYWALL ONLY. MUST BE BOLTED TO STUDS.
5
TV Wall Mount
OPTION 1
2.95 x 2.95 in/3.94 x 3.94 in (75 x 75 mm/100 x 100 mm)
Choose best installation option based on TV back panel hole spacing. See OPTION 2 on next page.
Step 3a
Attaching mounting plate
B
Carefully lay your TV on a rug or flat carton. Attach TV mounting plate (B) to back of the TV, by
selecting the proper mounting hardware. Spacers are included if screws are too long for screw
holes. (See page 2.) Hand tighten screws until the plate is attached and aligned. Then tighten each
screw snugly.
Step 4a
Installing TV on wall bracket
safety
screws
1. We strongly recommend two people, one on each side, lift the TV.
2. Carefully position TV over the wall bracket (A) until it locks in place.
3. Tighten both safety screws.
4. If you want to remove TV from the wall plate at a later time, you will need two people. One
person must hold the TV, while the second person loosens the two safety screws. Now with
one person on each side of the TV, remove the TV from the wall plate (A).
6
TV Wall Mount
OPTION 2
(7.87 to 23.6 in) x 15.7 in (200 to 600) mm x 400 mm
Choose best installation option based on TV back panel hole spacing.
Step 3b
Assembling TV mount
Gx4
Gx4
H
C
B
D
Measure the hole spacing on the back of your TV. Position two TV mounts (C) onto horizontal
attachment arms (D) at the same spacing you measured. Using Allen wrench (H), attach both
TV mounts (C) to attachment arms (D) with 4 screws (G).
Using Allen wrench (H), attach TV mounting plate (B) to attachment arms (D) with 4 screws (G).
Step 4b
Attaching TV mount
Carefully lay your TV on a rug or flat carton. Attach TV mounting assembly from Step 3b above
to back of the TV, by selecting the proper mounting hardware. Spacers are included if screws
are too long for screw holes. (See page 2.) Hand tighten screws until the plate is attached and
aligned. Then tighten each screw snugly.
7
TV Wall Mount
OPTION 2
Step 5b
Installing TV on wall bracket
safety
screws
1. We strongly recommend two people, one on each side, lift the TV.
2. Carefully position TV over the wall bracket (A) until it locks in place.
3. Tighten both safety screws.
4. If you want to remove TV from the wall plate at a later time, you will need two people. One
person must hold the TV, while the second person loosens the two safety screws. Now with
one person on each side of the TV, remove the TV from the wall plate (A).
8
Surge Protector
Operation Instructions:
Caution:
Plug Surge Protector into wall outlet first,
and then plug in electrical equipment
and connect coax cables.
Disconnect all electrical equipment
before removing Surge Protector from
wall outlet.
Technical Specifications:
Electrical Rating: 15A, 120 VAC, 60 Hz, 1800 Watts
Surge Lines Protected: 3-Line (L-N, L-G, N-G)
UL Clamping Voltage: L-N 500 V, L-G 500 V, N-G 500 V
Maximum Energy Dissipation: 900 Joules
Maximum Spike Current: 45,000 Amps (3 Line Total)
Response Time: <1 Nanosecond
EMI/RFI Noise Filter:
Frequency: 100 kHz ~ 100 mHz
Attenuation: Up to 40 dB
UL Listed to U.S
S tandards: UL 1449, UL 498A
9
Surge Protector
Information/Functions:
Surge Protection LED Indicator
 Protected Indicator - Red light
indicates your Surge Protection is
working properly.
Each outlet has a
cover that swivels
to protect from
electrical shock.
This wall tap surge protector is designed to protect your electronic equipment from AC
power surges up to a certain level. It’s not a lightning arrestor, so it won’t afford protection
while lightning strikes to nearby power lines, house, and/or service entrance antenna’s.
MOV (Metal Oxide Varistor) Technology
MOV component with improved material and surge functions absorbs surges.
Provides common and normal mode protection from high energy spikes. This device
features internal protection that will disconnect the surge protector at the end of its
useful life but will maintain power to the load.
High-Frequency Capacitor
Reduces noise interference.
Surge Protection for Ethernet/3D Coax Cable
Protects your Ethernet or Cable device.
Caution:
Do not plug the included surge protector into a power outlet that is different from the specs
called out. If you don’t know or are not sure about the type of electrical power that is supplied
to your home, please consult your local power company or a professional electrician. Use
indoors and in dry locations. Not for use with aquariums and other water-related products.
This surge protector must be plugged directly into the power source and must not be
'daisy chained' together in serial fashion with other power strips, UPS, other surge protectors
Risk of fire: Do not exceed electrical rating.
or extension cords.
Don’t force your surge protector’s plug into an outlet that isn’t designed to accept a threewire grounded-type AC plug (a three-prong plug). This plug is designed to be inserted into a
grounded-type outlet only. If this plug doesn’t fit directly into your outlet, do not attempt to
force it in. Never attempt to take apart the plug in any way (or alter the power cord). Don’t
attempt to defeat the grounding feature by using a 3-to-2 prong adapter. Don’t use with a
ground-fault circuit-interrupter receptacle. If you have questions about grounding, consult
your local power company or a qualified electrician.
10
HDMI Cables
Information:
This Kit includes 2 HDMI™ cables
The cables are 6 feet (1.83 m) and 9 feet (2.74 m) in length.
Technical Specifications:
1.4 Version
Supports Ethernet and 3D
O.D.: 6.0mm
Double molding
Cleaning Spray and Cloth
Instructions:
The Screen Cleaning Kit in this package includes:
1 Bottle of Anti-Run Anti-Static Screen Cleaning Gel and
1 Cleaning Cloth
6.76 oz (200 ml)
Cleaning Cloth measures 7.87 in. square (20 cm square)
Directions:
This special formula is designed for cleaning any type of screen, including LCD. The
gel does not run down the screen.
Please shake bottle before spraying. Hold screen cleaner about 6 inches (15cm) away
from the area to be cleaned. Spray screen, then use the included microfiber cloth to
clean and polish. Shake or wash the cloth regularly to prevent collected dirt from
making scratches. Do not spray excessive amount of cleaning gel.
Caution: Keep away from children.
Technical Specifications:
Anti-Static Screen Cleaning Gel: IPA Free, 6.76 oz (200 ml)
Cleaning Cloth : 7.87 in. square (20 cm square)
4 First aid measures:
1. After inhalation: Supply fresh air and consult doctor in case of complaints.
2. After skin contact:
Immediately wash with water and soap and rinse thoroughly.
If skin irritation continues, consult a doctor.
3. After eye contact:
Rinse opened eye for several minutes under running water. If symptoms
persist, see a doctor.
4. After swallowing: If symptoms persist consult a doctor
11
Velcro Cables Ties
Information:
This kit includes 2 Velcro cable ties.
Use 2 included Velcro cable ties to help manage your cords.
Each Velcro cable tie measures 8.66 in. (22.0 cm) in length.
Product Warranty:
The manufacturer warrants to the original purchaser that its products are free from defect in
materials and workmanship. If after inspection, we find that the product was defective in
materials or workmanship we shall repair or replace the product at our discretion. This
warranty does not cover accidental damage, misuse, improper care or alteration and
excludes claims for incidental or consequential loss. This limited warranty applies to
product purchased in the U.S. and Canada. This warranty gives you specific legal rights
and you may also have other rights which vary from State to State. The warranty duration
is one year from date of purchase.
Made in China
R1.0 120810 #63607076
12