TANSA GÜVENLİK SİSTEMLERİ ve SAAT SAN. TİC. A.Ş.

TANSA GÜVENLİK SİSTEMLERİ
ve
SAAT SAN. TİC. A.Ş.
SG-312 / SG-112 / SGWMC / LTT343
VIP SWING GATES
OPERATION & MAINTANANCE MANUAL
SG-312
SG-112
SGWMC
LTT-343
SWING GATES
Contents
1
2
3
4
5
6
Introduction
1.a
1.b
1.c
1.d
Page
General Information
Safety Warnings
Hardware Modifications
Packing Contents
1
1
1
1
Technical Specifications
2.a
General Description
2.b
Technical Specifications Chart
2.c
Dimentions
2.d
Options and Standart Specifications
2
3
4
6
Installation
3.a
3.b
3.c
3.d
3.e
3.f
3.g
7
7
7
8
10
11
13
Unpacking
Wiring
Field Arrangement and Positioning
Arm & Wing Installation
Ground Installation
Electrical Connections
Synchronization of Two Swing Gates
Mechanical & Electronical Specifications
4.a
Opening the Lid
4.b
Mechanism and Components
4.c
Control Board and Specifications
4.d
Setting Modes
14
15
16
17
Instructions for Use
5.a
Usage
5.b
Operating Modes
5.c
Operating System Specifications
18
18
19
Maintanance
6.a
Cleaning
6.b
Maintanance
20
20
SWING GATES
1 Introduction
1.a
General Information
Please read this manual carefully before installation. This manual includes
information about installation and maintanance for a long life-time of the
product.
TANSA have rights to make mechanical and electrical equipment changes on
products so there can be minor differences between the information on
operations manual and delivered products. OR TANSA reserves the right to
make changes on the products. The products on the data sheets may have
been upgraded or changed therefore may not reflect the units.
1.b
Safety Warnings
- The access keys to the mechanism must only be used by staff who have been
informed of the electrical and mechanical risks that they would run in the event of
negligent manipulation.
- Before opening the housing, cut off the power supply.
- Any internal element that could be live or in movement must be handled with care.
- The equipment has been configurated in "minimum risk" for its users. Installation,
settings and changings must be carried out with full knowledge of the facts by
qualified personnel and shall in no way invoke any liability for TANSA.
1.c
After Sales Modifications
If there will be a modification, component adding or changing, TANSA should be
informed for confirmation. Additional information can be needed and will be
provided by TANSA.
1.d
Packing Contents
a- 1 Unit SG-112/SG-312/SGWMC/LTT-343 swing gate.
b- 1 Unit 81cm arm (SG-312)
b- 1 Unit 80cm wing (SG-112)
b- 1 Unit 80cm wing (SGWMC)
b- 3 Units Glass wing (LTT-343)
c- 1 Unit Key (SG-112 / SG-312)
d- 2 Units Guidance sticker
e- Installation & Operating Manuel
SWING GATES
2
SPECIFICATIONS
2.a
General Discriptions
Drive
Bi-directional, electronic controlled and motorized
opening and closing.
Cabinet/Housing
AISI 304 (EN10082-2Grade 1G/2G) stainless
steel.
Arms & Wings
Clear acrylic in 10 mm thickness (SG-112, SGWMC,
LTT-343)
Aluminium (SG-312)
Operating Modes
Time setting for automatic closing or closing by a
push button.
Mechanism
All mechanism parts are located at the monobloc body.
body.
Power Supply
220 VAC 50/60Hz, optional 110VAC
Power Consumption
17/30 Watt
Control Board PSU
12VDC / 24VDC
Power Failure &
Emergency
Full integration with fire or alarm systems allowing
automatic sate-free (fail-safe) mode in case of
emergency or power failure (standard feature)
Operating Temperature
-10 to +55°C
Shipping & Storage Temperature
-20 to +55° C
Operating Humidity
95% Max.
SWING GATES
2.b Technical Specifications
You can find the below table regarding the technical specifications of swing gates.
MODEL
MECHANISM
CONTROL BOARD HEIGHT
CABINET
DIMENTIO
WEIGHT
POWER
COMSUMP.
OPERATING
TEMP.
POWER
SUPPLY
SG-112
VIP02v4
ECB-201R03
1050 mm 320X200 mm
35kg
max. 30 watt
- 10°, +55°
220 VAC/50 Hz
SG-312
VIP02v4
ECB-201R03
1050 mm 320X200 mm
31kg
max. 30 watt
- 10°, +55°
220 VAC/50 Hz
SGWMC
VIP04v2
ECB-201R03
1000 mm
170x170 mm
42kg
max. 30 watt
- 10°, +55°
220 VAC/50 Hz
LTT-343
VIP01v2
ECB-201R03
1000 mm
170x170 mm
73kg
max. 30 watt
- 10°, +55°
220 VAC/50 Hz
* All dimentions in milimeters.
* Standard arm length for SG-312 is 810 mm. Optional 1000 mm arm is available.
* Standard arm length for SG-112 is 800 mm. Optional 900 mm arm is available.
* Standard arm length for SGWMC is 800 mm. Optional 950 mm arm is available.
* All products can me manufactured in mild steel and powder coated upon request.
SWING GATES
2.c
Dimensions
SWING GATES
SWING GATES
2.d
Optional Accessories
OPTIONAL ACCESSORIES
MODEL
SG-112
SG-312
SGWMC
LTT-343
OPTIONAL
OPTIONAL
OPTIONAL
--
AUTOMATI
SECURITY
C OPENING
PHOTOCEL COUNTER
PHOTOCEL
L
L
OPTIONAL
-OPTIONAL
OPTIONAL
OPTIONAL
OPTIONAL
--
OPTIONAL
--
OPTIONAL
OPTIONAL
--
OPTIONAL
--
OPTIONAL
--
OPTIONAL
OPTIONAL
--
OPTIONAL STANDARD
--
OPTIONAL
--
REMOTE AUTOMATI
BUTTON
CONTROLL C OPENING CONTROL
ER
SENSOR
BOX
GLASS
WING
Remote Controller: Can be used to control all automatic swing gates. Open and Close functions
can be controlled seperately by two different buttons.
Automatic Opening Sensor: Can be used to control SG112 and SG312 swing gates in entrance
and exit directions seperately. For each direction a small ultrasonic sensor is mounted on the body
to sense the pedestrians from 20 cm up to 1 meter distance.
Button Control Box: Can be used to control all automatic swing gates. With two push buttons
(NO) Open and Close functions can be controlled seperately. Up to 5 different swing gates can be
controlled.
Glass Wing: Glass wing is standard in LTT-343 model. It is not used for other swing gates
because of its weight.
Security Photocell: Can be used in all models except LTT-343. This sensor prevents closing if
there is a pedestrian who stands in front of the closed arm position. Also during closing, if a
pedestrian comes to the closed arm position, the arm will stops and re-opens in order to prevent
hitting. This sensor consists two seperate parts. Transmitter and the reflector.
Counter: Can be used only in LTT-343 model to count the total passages in every direction.
Automatic Opening Photocell: Can be used in all models except LTT-343. This sensor consists
two seperate parts. Transmitter and the reflector. Both parts should be installed face to face from
any distance to swing gate to maintain a corridor. Wiring needed between the transmitter and the
swing gate. The sensor senses the pedestrian when he/she passes through the transmitter and
reflector, and the gate will opened automatically.
SWING GATES
3 INSTALLATION
3.a
Unpacking
Please check the swing gate visually after unpacking. If any damage or missing part is
realized place contact with TANSA.
3.b
Wiring
3x1.5mm power cable and 5A fuse needed for operating. 10A fuse recommended for
earth. Data cables should run on a different line than electrical cables.
3.c
Placing the Swing Gate
Ground should be flat. The body should be installed first and the arms later. 50 mm
distance recommanded between the swing gate and any other object around (See Part
3.e). It is optional to leave the distance more or less than that. Steel or chemical dowel
should be used for ground connections.
SWING GATES
3.d
Arm & Wing Installation
SG 112
1. Remove the bolts on the compression section.
2. Place the acrylic wing between the compression section and the gate body.
3. Screw on the bolts tightly.
SG 312
1. Remove the M4 socket cap bolts.
2. Place the aluminium arm through the arm support grip.
3. Screw on the M4 socket cap bolts tightly.
SWING GATES
SGWMC 1. Pull and remove the top lid.
2. Remove the bolts on the compression section.
3. Place the acrylic wing between the compression sections.
4. Screw on the bolts tightly.
5. Wear the top lid by pushing
SWING GATES
3.e
Ground Installation
SG112 / SG312: 1. Place the swing gate to its installation position. 2. Mark around
bottom of the body. 3. Remove the swing gate 4. Remove the M6 socket head bolts to
release the installation plate. 5. Place the installation plate on the marked surface. 6.
Mark the installation holes. 7. Drill the ground from marked spots. 8. Bolt down the
installation plate. 9. Place the swing gate on the installation plate and thighten the M6
socket head bolts.
2mm Distance
SGWMC / LTT-343: 1. Remove the upper part of the body from the bottom part 2.
Remove the bottom part from the frame which is welded to installation plate. 3. Mark
and drill the installation holes. 4. Place the bottom part of the body and screw on to the
frame. 5. Complete the wiring. 6. Place the upper part of the body and screw on tightly.
Drw 3
Drw 1
Drw 4
Drw 2
Drw 5
Drw 6
SWING GATES
3.f
Electrical Connections (External Connections)
1
1- +24 VDC1
2- GND2
3- +12 VDC2
4- GND1
1- +24VDC Out
2- Direction A-B control input (NO)
3- Direction B-A control input (NO)
4- Optional Input
5- Emergency input (NC)
6- GND
1- +24VDC Out
2- Security photocell input
3- Optional input
4- Optional input
5- Direction switch input
6- GND
1- Direction A output COM
2- Direction A output NO (SG343)
3- Direction B output COM
4- Direction B output NO (SG343)
5- Optional output COM
6- Optional output NO
- NO relays or PNP should be connected for direction control inputs.
- NC relays should be connected for emergency input. On J17 terminal #1 and #2 should be connected by
short-circuit if there will be no emergency control.
SWING GATES
Direction Control Inputs (NO)
Direction Control Inputs (+9/24VDC)
J17
+
OUT +
A-B Reader
J17
+
-
OUT +
A-B B-A
B-A Reader
NC Emergency Input
Connection (If not used
connect with a shortcircuit)
Counter Input SG343
J18
J19
Drawing shows a counter
connection on direction A-B. For
a counter on B-A direction use
#3 and #4 of the J19 terminal.
Counter 24VDC
SWING GATES
3.g
Synchronization of Two Swing Gates
For synchronization of two swing gates which placed face to face below
connections required.
Control Board (1st swing gate)
Control Board (2nd swing gate)
!!! SHOULD
NOT BE
CONNECTED
A-B Direction B-A Direction
Control Input Control Input
(NO)
(NO)
+ - D
24VDC
PNP NO
Security
Photocell
!!! SHOULD
NOT BE
CONNECTED
A-B Direction
Control Input
(NO)
+ - D
24VDC
PNP NO
Free passage
sensor
SWING GATES
4. Mechanical & Electronical Specifications
4.a Openning the Lid (SG-112 / SG-312)
1
2
1. Unlock the lid by turning clockwise.
2. Pull the front part of the lid 1/2 cm.
3. Push the lid to the back side.
4. Pull the complete lid up.
3
4
SWING GATES
4.b Mechanism SG112 / SG312
1
14
2
3
3
12
4
5
11
7
8
10
9
15
6
1- A-B direction locking solenoid
2- B-A direction locking solenoid
3- Solenoid bracket
4- Motor
5- Motor mounting and streching
bracket
6- Motor belt
7- Rotor pulley
8- Sensor plate
9- Sensor mounting plate
10- Optical sensor
11- Lock arm
12- Lock arm spring
13- Motor strecher spring
14- Main mechanism plate
15- Motor pulley
10
13
SWING GATES
4.c
Control Board & Specifications
- Green led ligh always flashes if the microprocessor is on.
- Red led lights always on and shows the power is on.
- The barcode on the microprocessor should never removed. The barcode defines the
version and operatioanl mode of the control board.
ECB-201 R03 Swing Gate Control Board
13
4
3
2
1
6
5
11
10
14
1
7
8
9
1- Control Board Main Power Input 24VDC / 12VDC
2- Swing speed control relay connection
3- Not used
4- Not used
5- A-B direction solenoid output
6- B-A direction solenoid output
7- Control inputs
8- Optional input
9- Counter output relay NO kontak (SG343)
10- Power voltage selection for control
11- Rotation sensor input
12- PC communication port (TTL Optional)
13- Mode setting switches
14-Motor connector
SWING GATES
4.d
Sw1 - Sw2
Setting Modes
Automatic Closing Time Setting
Sw1 ON - Sw2 ON
Sw1 OFF - Sw2 ON
Sw1 ON - Sw2 OFF
Sw1 OFF - Sw2 OFF
Sw3 - Sw4
Sw5
Direction Control
Sw3 ON
Sw3 OFF
Sw4 ON
Sw4 OFF
20 seconds
15 seconds
10 seconds
5 seconds
A-B direction controlled
A-B direction free
B-A direction controlled
B-A direction free
Not Used
Sw5 ON
Sw5 OFF
After the gate is completely opened, an
automatic closing time can be set.
These switches are not used. Should
always be ON position.
Not used. Can be on ON or OFF position.
Sw6
Automatic Closing Setting
Sw6 ON
Automatic closing active When the automatic closing is active, the
Sw6 OFF
Automatic closing passive gate will be closed automatically after the
set time. When the automatic closing is
passive, control signal needed (E.G.push
button) for closing the gate.
Sw7
Minumum control input signal time
Sw7 ON
200mS
Sw7 OFF
20mS
Control input signal
Sw8
Warning Voice Control
Sw8 ON
Warning voice ON
Sw8 OFF
Warning voice OFF
If the control input signal time is too short
or several control signals received for group
entrances or exits, switch should be in OFF
position. For standard use, switch should
be in ON position.
If the switch is ON position, after receiving
an OPEN signal, a continious "beep tone" is
heard.
SWING GATES
5 Instructions for Use
5.a
Usage
Any kind of access control system can be easily connected to swing gate (card or
biometric readers, push botton, remote controller, coin or token acceptor... etc).
Do not push or pull the arm during operation.
Do not put anything such as purse, suitcase etc. on the gate cabinet.
Swing gates are fail-safe during emergency or power failure.
5.b
Operating Modes
Swing gates are fail-safe during emergency or power failure (Standard)
Swing gates are fail-locked during emergency or power failure (Optional)
SWING GATES
5.c
Operating System Specification
Swing gates have full control in both directions by a microprocessor controller and can be easily
connected to any kind of access control system (card or biometric readers, push botton, remote
controller, coin or token acceptor... etc). Can remain OPEN for allotted times. Double units can be
controlled syncronised in face to face installation in order to prevent larger entrances or exits.
MODEL
MECHANICAL SYS.
MANUEL
OPERATING SYSTEM
MATERIAL SPECIFICATION
MOTOR
DRIVE
LOCKING
BRAKE
CABINET/HOUSING
ARMS/WINGS
SHAFT
SG112
YES
Motor
Solenoid
Electronic
Stainless /Powder Coated
10mm Acrylic
Stainless
SG312
YES
Motor
Solenoid
Electronic
Stainless /Powder Coated
10mm Acrylic
Stainless
SGWMC
YES
Motor
Solenoid
Electronic
Stainless /Powder Coated
10mm Acrylic
Stainless
LTT-343
YES
Pushing/Motor Solenoid
Electronic
Stainless /Powder Coated
10mm Tempered Glass
Stainless
SWING GATES
6 Maintanance
6.a
Cleaning
Periodical body, arm and wing cleaning is recommanded.
Cleaning supplies that contain acidic chemicals might damage AISI 304 stainless
steel and leave a stain on it.
Please use liqued cleaners that contain soft chemicals such as stainless steel or
window cleaning sprays.
6.b
Maintanance
Dust and dirt can effect the life-time of the mechanism. Mechanizm should be
cleaned periodically.
- Before opening the housing, cut off the power supply.
SWING GATES
*TANSA reserves the right to modify design and details.
Address
Abdurrahman Gazi Mah. Alparslan Cad.
Selma Sok. No:2
34887 Sancaktepe – Istanbul
TURKEY
Telephones
+90 216 561 96 71-72-73
Fax
+90 216 561 96 74-75