Hose Catalog

Transcription

Hose Catalog

HOSE
CATALOG
pirtekusa.com
HYDRAULIC HOSES
RUBBER HOSES - INDEX
SELECTION GUIDE
Page
Group
Product Codes
Construction
Normal Usage
Features & Benefits
(See main Specification pages for details and Approvals)
C21
Isobaric 210 bar
17-21
C25, PC25
Isobaric 250 bar
19-22
C35, PC35
Isobaric 350 bar
20-23-24
C42, P42, PC42
Isobaric 420 bar
18
C45
Isobaric 450 bar
11-12
R1AT / R1ATFS
One wire braid
Medium pressure hose for hydraulic fluids
and aqueous emulsions and water
Normally black but R1ATFS has red cover to
indicate use in fire suppression systems
R2AT/2SC
Two wire braid
R2ATHT
High Temp. 2 wire hose
High pressure hose for hydraulic fluids and
aqueous emulsions and water
Synthetic rubber oil resistant liner and
abrasion resistant cover. 2 steel braids
High pressure hose for hydraulic fluids and
aqueous emulsions and water
As above but high temperature rubber
formulation. Blue cover
100R5
Engine & Air Brake
Specifically intended for trucking industry
applications involving diesel fuel / air brakes
Black rubber with poyester textile outer cover
for safe escape of entrapped air
R5HT
Hi-Temp. Truck Hose
Medium pressure air and hydraulic hose
common on American equipment
Internal diameters match the inside diameter
of copper tube to yield an unrestricted flow
6
R4HT
Oil Suction
High temperature hydraulic suction &
delivery hose for fuels & mineral
Synthetic smooth oil resistant inner tube. 2
braids of textile & a steel helix. MSHA
7
100R4
Oil Suction
Hydraulic suction & delivery hose
Synthetic smooth oil resistant inner tube. 2
braids of textile & a steel helix. MSHA
High pressure multi-spiral hose for hydraulic
fluids such as glycol, mineral oils, fuels,
hydrocarbons etc.
Provide flexibility and high temperature
resistance
Compatible with Caterpillar® reusable fittings
High quality black multi-purpose hose with
spiral wound textile reinforcement
Synthetic black rubber inner and outer.
Abrasion and weather resistant. Oil resistant
15
MPH
Multipurpose
JH70
Jacking Hose
High pressure hydraulic hose for jacking
applications
Synthetic rubber oil resistant liner and
abrasion resistant cover. 2 steel braids
25
JBF
Large Bore Hose
Large bore medium pressure hose for
hydraulic fluids incl. aqueous emulsions
Spiral construction. Prolonged usage with
water based fluids will corrode reinforcement
26
LPG
LP Gas Hose
High pressure hose for transfer of LPG,
Woven black poly cover with blue trace over
single st. steel braid / teflon liner. AGA approved.
14
10
9
HYDRAULIC
13
27
R12C
4000-2500 psi Spiral
28
R13C
5000psi Spiral
8
Class 21 hoses suit 210 bar WP
Isobaric (constant working pressure for all
sizes) range of hoses exclusive to PIRTEK.
Simplifies hose selection in circuits of known
working pressure
‘PS’ Suffix denotes extreme abrasion resistant
sheath over the cover
‘PC’ Prefix denotes Komatsu® genuine hoses
butane-propane on stationary and mobile eqpm’t.
This page is part of a complete catalogue containing technical and safety data.
All data must be reviewed when selecting a product.
PIRTEK reserve the right to change technical specifications without notice
SAFETY WARNING
16
1
REV 62116
B
SELECTION GUIDE
Page
Group
Product Codes
Construction
Normal Usage
Features & Benefits
(See main Specification pages for details and Approvals)
29
TPR7
General purpose R7
General hydraulics, material handling,
pneumatics, and agricultural equipment
The original SAE 100R7 design with
polyester tube and polyurethane cover.
30
TPR7X2
General Purpose R7
General hydraulics twinline, material handling,
pneumatics, and agricultural equipment
Polyester core and good cold weather
flexibility. SAE 100R7 performance
31
TPR7NC
Non-Conductive R7
Non conductive hydraulic hose for aerial
lift equipment
Polyester core and good cold weather
flexibility. SAE 100R7 performance
TP1W
Low temperature hydraulic & gas hose.
Recommended for mobile equipment
Good cold weather and cold room flexability
Good bend radius and kink resistance
TP1WX2
One Wire Thermoplastic High Pressure Jacking
Low temperature hydraulic & gas hose.
Recommended for mobile equipment
Good cold weather and cold room flexability
Good bend radius and kink resistance
TPR8
High Pressure R8
Pilot lines, general hydraulics, and machine
tools at higher pressures than 100R7
R8 Performance with compact R7
dimensions
33
TPR8NC
Non-conductive R8
Non conductive hydraulic hose for aerial lift High pressure general hydraulic systems
equipment with higher working pressures
that may contact high voltage sources
36
STH
St. Steel Teflon® hose
Laundry equipment, plastic moulding presses,
steam and hot air discharge
34
RUBBER HOSE
35
32
THERMOPLASTIC
HYDRAULIC HOSES
THERMOPLASTIC HOSES - INDEX
One Wire Thermoplastic High Pressure Jacking
Teflon liner and SS braid allow high
temperature and chemical capability
ORDERING PIRTEK ASSEMBLIES
Should you wish to describe a PIRTEK hose assembly in an abbreviated form, please use the following format. A forward slash is used to
separate each field. Product Codes for fittings can be found in PIRTEK Catalogue Section C (except Mining Fittings Section U).
If spiral guard PSAW-025 were fitted over the full length, the designation would be:
R1AT-12 / JF1-1212J / C614-1212J / 1200 / PSAW-025
If both ends were fitted with the 45° flanged elbow set in alignment, the designation would appear:
R1AT-12 / C614-1212J / 1200 / 0
Generic Pattern : Hose / End A / End B / Length / Protection / Angle
2
B
REV 62116
HYDRAULIC HOSES
WARNING
SAFETY PRECAUTIONS FOR
THE USE OF
PIRTEK® HOSE ASSEMBLIES
Your Personal Safety may directly or indirectly be compromised if the hose assembly is abused.
By following the INSTRUCTIONS below, the more common abuses of hose and hose assemblies can be
avoided.
INSPECT the hose assembly before each use.
RUBBER HOSE
REPLACE the hose assembly immediately if:
A.
The cover appears abnormal
B.
You believe it may be abnormal
C.
There is any fluid leakage
D.
The fittings are damaged
E.
The hose is damaged
F.
Reinforcement is visible through the cover
DO NOT EXCEED the maximum working pressure of the hose.
DO NOT KINK the hose assembly.
DO NOT BEND beyond the specified minimum bend radius of the hose.
DO NOT EXPOSE to temperatures beyond the published maximums for the hose or fluid being conveyed.
DO NOT USE AS A STRENGTH MEMBER for pulling or lifting equipment. Use support cables for vertical
installations.
USE ONLY WITH COMPATIBLE FLUIDS as outlined in the Chemical Compatibility Charts or as specifically
approved in writing by PIRTEK Fluid Systems.
PIN PRICK THE COVER of hoses used for compressed air above 17 bar or 250 psi to allow the safe escape
of air that permeates through the liner and reinforcement (except STH and R5HT). The maximum working
pressure and temperature must also be reduced by 30%.
Use only PIRTEK HOSE AND FITTINGS COMBINATIONS as designated in their current assembly guidelines.
Use only PIRTEK PROCEDURES and ASSEMBLY EQUIPMENT as published and maintained in their
M.A.P.S. documentation.
Relationship between actual working presasure and service life
Experimental pressure waveform
Pressure as a % of
Rated Pressure at 100
90
80
70
% of Service Life
• The use of conventional wire reinforced
rubber hose often entails the pressure
fluctuations of fluid.
• The factors concerned with such pressure
fluctuations are generally classified into two:
those stemming from the pump itself, and
the others ascribable to external impacts
imparted to the hose via the operating
demands. The latter are considered to have
the greater effect on the service life of the
hose.
• External impulse pressure is estimated to
be 150% of the set pressure (actual working
pressure) of a relief valve, and sometimes
exceeds 300%.
100
60
150
125
5% of one cycle
Rated pressure
100
75
50
25
(kgf/cm )
0
50
Peak pressure 150 ± 7%
Pressure rising rate
2
40
15% of one cycle
1/35 minute a cycle
30
20
10
0
100 125 150
200
300
400
Actual working pressure
Recommended working pressure
500
600
%
3
REV 62116
B
HYDRAULIC HOSES
FAST FIND TABLE
SIZE, PRESSURE, TEMPERATURE
Product Code & Hose Type
Dia. (ins.)
mm size
C21
Isobaric 210 bar
C25, PC25
Isobaric 250 bar
C35, PC35
Isobaric 350 bar
Working Pressure PSI
Temp.
⅛
³/₁₆
¼
⁵/₁₆
⅜
½
5/₈
¾
1
1¼
1½
1¾
-003
-004
-006
-008
-010
-013
-016
-019
-025
-032
-038
-045
2
2½
3
3½
4
5
-050
-063
-076
-090
-100
-125
3045
5510
C42, PC42, P42 Isobaric 420 bar
3625
3625
3625
3625
3625
-40°/+212°
-40°/+212°
5076
5076
5076
5076
5076
5076
5076
5076
-40°/+248°
6091
6091
6091
6000
6091
6091
6091
6091
6091
-40°/+248°
1522
1276
913
725
580
6525
FAST FIND TABLE
C45
Isobaric 450 bar
R1AT
1-Wire Hydraulic
3263
2610
2320
R1ATFS
Fire Suppression
3263
2610
2320
R2AT/2SC
2-Wire Hydraulic
5801
4786
3988
3625
3118
2393
2204
1305
1160
-40°/+212°
R2ATHT
2-Wire High Temp
5743
5004
4250
3249
3002
2494
2248
1740
1494
-40°/+302°
100R5
Engine/Air Brake Hose
Unique diameters throughout range 3/16” to 1.13/16”
100R5HT
High Temp 100R5
Unique diameters throughout range 3/16” to 1.13/16”
100R4
Hydraulic Suction/Delivery
300
250
200
150
100
62
56
R4HT
Hydraulic Suction/Delivery
304
289
203
145
145
145
188
R12C
4000-2500 psi Spiral
4000
4000
3002
2495
2495
-40°/+249°
R13C
5000 psi Spiral
5000
5000
5000
5000
5000
-40°/+249°
MPH
Multipurpose
500
500
500
JH70
Jacking Hose
10150
JBF40
Large Bore
LPG
LPG Gas Hose
TPR7
Medium Pressure
3335
3045
2900
2755
TPR7X2
MP Twin Line
3335
3045
2900
2755
TPR7NC
Non-conductive
TP1W
1 Wire Thermoplastic
4712
4350
TP1WX2
Twin 1 Wire thermoplastic
4712
4350
TPR8
High Pressure
5075
TPR8NC
HP Non-conductive
5075
STH
Stainless Steel Teflon Hose
500
1885
-40°/+212°
-40°/+212°
1522
4000
4000
4000
500
500
500
-40°/+212°
-40°/+300°
-40°/+300°
-40°/+200°
188
188
-40°/+212°
2030
377
3000
-40°/+212°
377
-20°/+257°
2537
2030
-65°/+212°
2537
2030
-65°/+212°
2537
2030
-40°/+212°
3480
3262
2755
-65°/+212°
3480
3262
2755
-65°/+212°
4060
3552
-65°/+212°
4060
3552
-65°/+212°
2250
1750
2900
3000
-40°/+275°
-40°/+212°
10150
2500
1500
1100
900
Pg.
Range
min-max
-65°/+466°
16
17,21
19,22
20,23,24
18
11
12
13
14
10
9
7
6
27
28
8
15
25
26
29
30
31
34
35
32
33
36
Chemical Compatibility Tables Begin On Page 39
4
B
REV 62116
HYDRAULIC HOSES
R4HT
HIGH TEMP OIL SUCTION & DELIVERY
Construction
Applications
Reference Specifications
Inner Tube:
Hardwall hose for suction and delivery of oil
Tested in accordance with performance
Black smooth NBR (Nitrile) compound, oil
at high temperatures in hydraulic systems.
specifications: SAE100 R4.
resistant.
Extremely flexible.
Approvals: MSHA
Reinforcement:
Temperature Range:
Prolonged usage with water based fluids at
High strength synthetic cord plus embedded
-40°F up to +275°F mineral oil
temperatures above 158°F will allow wire
steel helix wire.
-40°F up to +158°F water based fluids
corrosion as a result of diffusion through the
inner liner.
Cover:
RUBBER HOSE
6
B
Black, smooth (wrapped finish) Hypalon rubber
Hose Tails:
compound flame retardant, resistant to abrasion,
PIRTEK ‘J’ Series for some sizes
oils and weathering.
L Series, Cam & Groove, Combination Steel
(all with clamps).
PIRTEK R4 HIGH TEMP R4HT-32 2” (50.8mm) 145 PSI (10 BAR) MSHA
Lay line example: Embossed text on black. Comment: Lay line example may not be a true indication of current status. Refer to PIRTEK for current information.
R4HT-12
mm
19.1
ins
3/4
mm
30.5
working
304
min burst
1,203
vacuum
0.9
Min bend
radius
mm
60
R4HT-16
25.4
1
37
289
986
0.9
80
0.56
R4HT-20
31.8
1.1/4
44
203
812
0.9
100
0.68
R4HT-24
38.1
1.1/2
50
145
580
0.9
125
0.89
R4HT-32
50.8
2
63
145
580
0.9
150
1.51
R4HT-40
63.5
2.1/2
80
145
580
0.9
200
1.81
R4HT-48
76
3
92
188
754
0.9
240
2.20
R4HT-56
89
3.1/2
108
188
754
0.9
280
2.88
R4HT-64
102
4
121
188
754
0.9
320
3.22
Product Code
Nominal ID
OD
Pressure PSI
Weight
lb/ft
0.44
REV 62116
HYDRAULIC HOSES
100R4
OIL SUCTION & DELIVERY
Construction
Applications
Inner Tube:
Hardwall hose for suction and delivery of oil in
Black, oil resistant Nitrile (NBR).
hydraulic systems. Extremely flexible.
specifications: SAE100 R4.
Reinforcement:
Temperature Range:
Approvals: MSHA IC-31/5
Two textile braids, pre-treated for tube and
Prolonged usage with water based fluids at
cover adhesion. Helix wires are located between
temperatures above 140°F will allow wire
bending.
inner liner.
Cover:
Hose Tails:
Black, oil and weather resistant Neoprene (CR)
PIRTEK ‘J’ Series for some sizes
MSHA apporved.
Cam & Groove, Combination Steel
RUBBER HOSE
the braids to resist collapse under vacuum or
(all with clamps).
PIRTEK SAE 100R4-20 Suction Hose 1 1/4” (31.75mm) 200 PSI (13.79 BAR) MSHA
Lay line example: Embossed text on black. Comment: Lay line example may not be a true indication of current status. Refer to PIRTEK for current information.
ins
3/4
mm
31.50
working
300
min burst
1,200
in/hg
25.00
Min bend
radius
mm
127
25.4
1
38.90
250
1,000
25.00
153
0.57
31.8
1.1/4
45.20
200
800
25.00
203
0.67
100R4-24
38.1
1.1/2
52.58
150
600
25.00
254
0.84
100R4-32
50.8
2
64.51
100
400
25.00
305
1.03
100R4-40
63.5
2.1/2
79.25
62
250
25.00
356
1.70
100R4-48
76
3
91.95
56
225
25.00
457
1.99
100R4-56
89
3.1/2
105.20
45
180
25.00
533
2.34
100R4-64
102
4
119.40
35
140
25.00
610
3.03
Product Code
Nominal ID
100R4-12
mm
19.1
100R4-16
100R4-20
OD
Pressure PSI
Weight
lb/ft
0.42
7
REV 62116
B
HYDRAULIC HOSES
MPH
MULTIPURPOSE HOSE
Construction
Applications
Inner Tube:
Low pressure hose for fluids such as mineral
Exceeds SAE J 517 (100 R6).
Black, smooth NBR (Nitrile) seamless synthetic
and vegetable oils, aqueous emulsions, water,
Exceeds EN 854 R6
rubber, oil resistant.
air and inert gases.
JIS B 8360.
Reinforcement:
Temperature Range:
Impulse Testing:
Two or four spirals of textile fiber.
Water +32ºF to +122ºF (continuous)
400,000 cycles of JIS waveform @ 133%
Water +32ºF to +158ºF (temporary)
of working pressure (hose only) all sizes
Air -40ºF to +122ºF (in case of air applications,
Safety Factor 4:1.
Cover:
Black CR (Neoprene) synthetic rubber compound pressure should be less than 15bar)
Hose Tails:
resistant to abrasion, oils, ozone and weathering. Other fluid -40°F up to +212°F
RUBBER HOSE
-40°F up to 158°F external ambient
PIRTEK ‘T’ Series option on 3/8, 1/2, 5/8 sizes.
PIRTEK MULTI MPH-12 3/4” (19.1mm) 500 PSI (35 BAR) W.P.
Lay line example: Green text on black. Comment: Lay line example may not be a true indication of current status. Refer to PIRTEK for current information.
Product
Code
MPH-04
MPH-05
MPH-06
MPH-08
MPH-10
MPH-12
MPH-16
8
B
PIRTEK ‘P’ Series
Nominal ID
mm
6.3
8.0
9.5
12.7
15.9
19.0
25.4
in
1/4
5/16
3/8
1/2
5/8
3/4
1
Reinforcement
OD
4 fabric spiral
4 fabric spiral
4 fabric spiral
4 fabric spiral
2 fabric spiral
4 fabric spiral
4 fabric spiral
mm
14.0
15.8
17.4
21.3
23.5
31.4
37.5
Pressure PSI
working
500
500
500
500
500
500
500
min burst
2,000
2,000
2,000
2,000
2,000
2,000
2,000
Min bend
radius
Weight
mm
55
60
65
90
110
135
170
lb/ft
0.10
0.12
0.14
0.19
0.20
0.40
0.50
REV 62116
HYDRAULIC HOSES
100R5HT
LOW PRESSURE HOSE
Construction
Applications
Inner Tube:
Low to medium pressures hose that will handle
Exceeds SAE J 517 (100 R5).
Seamless CPE/AQP rubber, oil resistant.
high temperature hydraulic fluids such as mineral
aqueous emulsions, water, air and inert gases
Impulse Testing:
See Table below for Impulse Test criteria
(hose only).
Temperature Range:
Hose Tails:
and vegetable oils, diesel, B20, petrol, E10,
Reinforcement:
One textile braid and one braid of high tensile
steel wire.
-40°F up to +300°F hydraulic, transmission oils
Cover:
& Diesel
Blue synthetic rubber with blue polyester textile
-40°F up to +212°F E10 & B20 (biodiesel)
outer braid resistant to abrasion, oils, ozone and
+32°F up to +179°F water, water based fluid &
PIRTEK ‘A’ Series (Field Attachable).
of entrapped air when used to conduct high
+32°F up to +158°F air
pressure air.
-40°F up to +249°F ambient
Product
Code
100R5HT-04
100R5HT-05
100R5HT-06
100R5HT-08
100R5HT-10
100R5HT-12
100R5HT-16
100R5HT-20
100R5HT-24
100R5HT-32 †
Nominal ID
mm
5.1
6.8
8.3
10.7
13.2
16.4
22.8
29.2
35.5
46.6
in
3/16
1/4
5/16
13/32
1/2
5/8
7/8
1.1/8
1.3/8
1.13/16
OD
mm
13.2
14.8
17.1
19.5
23.4
27.4
31.4
38.1
44.4
56.2
Pressure PSI
working
3,000
3,000
2,250
2,000
1,750
1,500
800
625
500
300
min burst
12,000
12,000
9,000
8,000
7,000
6,000
3,200
2,500
2,000
1,200
Min bend
radius
Weight
mm
76
86
102
117
140
165
187
229
267
337
lb/ft
0.12
0.16
0.22
0.26
0.36
0.44
0.46
0.52
0.67
0.94
Test Impulses
150 000
150 000
150 000
150 000
150 000
150 000
150 000
100 000
100 000
100 000
RUBBER HOSE
weathering. Permeable cover allows safe escape glycol (anti-freeze)
† Does not comply with SAE 100R5 operating pressure of 348 psi or minimum burst pressure of 1,392 psi.
9
REV 62116
B
HYDRAULIC HOSES
100R5
ENGINE & AIR BRAKE* HOSE
LOW PRESSURE HOSE
Construction
Applications
Inner Tube:
Low to medium pressures hose that will handle
* SAE J1402 Type AII in sizes -04 through -12.
Seamless oil resistant nitrile.
high temperature hydraulic fluids such as mineral
D.O.T. FMVSS106.
and vegetable oils, aqueous emulsions, diesel,
Consult PIRTEK for specific Industry Approvals.
Reinforcement:
lubricating oils, coolants, water, air and inert gases SAE J1402 AII Standard.
One fiber braid and one braid of high tensile
steel wire.
Cover:
Temperature Range:
Hose Tails:
-40°F up to +300°F hydraulic, transmission oils
PIRTEK ‘A’ Series (Field Attachable).
& Diesel
Black synthetic rubber with black polyester textile +32°F up to +179°F water, water based fluid &
outer braid resistant to abrasion, oils, ozone and
RUBBER HOSE
10
B
glycol (anti-freeze)
weathering. Permeable cover allows safe escape +32°F up to +158°F air
of entrapped air when used to conduct high
pressure air.
Product
Code
100R5-04
100R5-05
100R5-06
100R5-08
100R5-10
100R5-12
100R5-16
100R5-20
100R5-24
100R5-32
Nominal ID
mm
4.8
6.4
7.9
10.4
12.7
15.9
22.4
28.7
35.1
46.6
OD
in
3/16
1/4
5/16
13/32
1/2
5/8
7/8
1.1/8
1.3/8
1.13/16
mm
13.7
15.7
17.7
20.1
24.0
27.9
32.3
38.9
46.0
56.4
Pressure PSI
working
3,000
3,000
2,250
2,000
1,750
1,500
800
625
500
350
min burst
12,000
12,000
9,000
8,000
7,000
6,000
3,200
2,500
2,000
1,400
Min bend
radius
Weight
mm
75
85
100
115
140
165
185
230
265
335
lb/ft
0.013
0.16
0.19
0.22
0.34
0.39
0.37
0.46
0.57
0.89
REV 62116
HYDRAULIC HOSES
R1AT
SINGLE WIRE BRAID
Applications
Inner Tube:
Medium pressure hose for hydraulic fluids such
Seamless NBR (Nitrile) rubber, oil resistant.
as mineral oils, aqueous emulsions, water, air
specifications: SAE100 R1AT S
and inert gases.
EN853 1SN.
Temperature Range:
Approvals:
SAE J1942
Cover:
AS2660 test requirements-
Black synthetic rubber resistant to abrasion, oils,
+32°F up to +140°F water
AS1180 10B and AS1180.13A (FRAS)
ozone and weathering.
MSHA approval No. 1C-104/3
-40°F up to 158°F ambient
Prolonged usage with water or water based
Cover must be pin pricked if hose is to be used
fluids at temperatures above 158°F will allow
to convey air above 246 psi.
wire corrosion as a result of diffusion through the
Reinforcement:
One braid of high tensile steel wire.
HF Type B
inner liner.
Hose Tails:
PIRTEK ‘K’ Series to 5/8”
PIRTEK ‘J’ Series 3/4” to 2”
PIRTEK SAE 100R1 AT TYPE S R1AT-04 1/4” (6.4 mm) 3263 PSI (225 BAR) MSHA FRAS
RUBBER HOSE
Construction
HF TYPE B
Lay line example: White text on black. Comment: Lay line example may not be a true indication of current status. Refer to PIRTEK for current information.
Product
Code
R1AT-04 *
R1AT-06
R1AT-08
R1AT-10
R1AT-12
R1AT-16
R1AT-20
R1AT-24
R1AT-32
Nominal Diameter
DN
6
10
13
16
20
25
32
40
50
inch
1/4
3/8
1/2
5/8
3/4
1
1 1/4
1 1/2
2
*Note: R1AT-04 is only included in SAE J1942
mm
6.4
9.5
12.7
15.9
19.1
25.4
31.8
38.1
50.8
Reinforcement
1 braid
1 braid
1 braid
1 braid
1 braid
1 braid
1 braid
1 braid
1 braid
OD mm
Cover
13.7
17.7
20.8
23.6
28.0
36.2
47.6
54.0
68.3
Pressure PSI
working
3,263
2,610
2,320
1,885
1,522
1,276
913
725
580
burst
13,050
10,440
9,280
7,540
6,090
5,104
3,654
2,900
2,320
Min. bend
radius
mm
100
125
180
201
240
300
420
500
630
Weight
lb/ft
0.15
0.24
0.30
0.33
0.41
0.62
0.91
1.14
1.63
HF Type B
11
REV 62116
B
HYDRAULIC HOSES
R1ATFS
SINGLE WIRE BRAID
FIRE SUPPRESSION APPROVAL
Construction
Applications
Inner Tube:
SAE J 517 (SAE 100R1AT)
Seamless synthetic rubber, resistant. to oil.
such as mineral and vegetable oils, aqueous
EN 853 1SN
emulsions and water.
Former DIN 20022 1SN (part 3)
Reinforcement:
Meets hose requirements outlined in AS5062.
Temperature Range:
One braid of high tensile steel wire.
Approvals:
-40°F up to +212°F (257°F intermittent)
Cover:
MSHA 2G in all sizes
Red synthetic rubber resistant to abrasion, oils,
Comment:
Approved within Australia for use on fire
Lay line example may not be a true indication
suppression systems.
of current status. Refer to PIRTEK for current
Impulse Testing:
RUBBER HOSE
information.
All sizes tested to 150,000 cycles
(hose only).
Hose Tails:
PIRTEK ‘J’ Series 3/4”
PIRTEK R1ATFS — DIN EN 853 1SN 25mm (1”) R1AT-16 88 BAR (1,200 PSI) WORK. PRESS. MSHA
Lay line example: White text on red. Comment: Lay line example may not be a true indication of current status. Refer to PIRTEK for current information.
Nominal Diameter
Product Code
R1ATFS-04
R1ATFS-06
R1ATFS-08
R1ATFS-12
12
B
DN
6
10
12
19
inch
1/4
3/8
1/2
3/4
OD mm
mm
6.4
9.5
12.7
19.0
Wire
11.1
15.1
18.3
25.4
Pressure PSI
Cover
13.4
17.4
20.6
27.7
working
3,263
2,610
2,320
1,522
burst
13,050
10,440
9,280
6,090
Min. bend
radius
Weight
mm
100
130
180
240
lb/ft
0.15
0.22
0.27
0.41
REV 62116
HYDRAULIC HOSES
R2AT/2SC
TWO WIRE BRAID
Applications
Inner Tube:
Medium to high pressure hose for hydraulic fluids Tested in accordance with performance
such as mineral oils, aqueous emulsions, water,
specifications: SAE100 R2AT
air and inert gases.
EN853 2SN
Temperature Range:
Approvals:
SAE J1942
Cover:
AS1180.10B and AS1180.13A (FRAS)
MSHA Approval No. IC-104/3
to convey air above 246 psi.
Reinforcement:
Two braids of high tensile steel wire.
HF Type B
inner liner.
Hose Tails:
PIRTEK SAE 100R2AT R2AT-12 3/4” (19.1 mm) 3118 PSI (215 BAR) MSHA FRAS
RUBBER HOSE
Construction
HF TYPE B
Product
Code
R2AT-04
R2AT-06
R2AT-08
R2AT-10
R2AT-12
R2AT-16
R2AT-20
R2AT-24
R2AT-32
Nominal Diameter
DN
6
10
13
16
20
25
32
40
50
inch
1/4
3/8
1/2
5/8
3/4
1
1 1/4
1 1/2
2
mm
6.4
9.5
12.7
15.9
19.1
25.4
31.8
38.1
50.8
Reinforcement
OD mm
2 braids
2 braids
2 braids
2 braids
2 braids
2 braids
2 braids
2 braids
2 braids
15.3
19.3
22.4
25.8
29.8
38.5
49.6
56.0
68.6
Cover
Pressure PSI
working
5,801
4,786
3,988
3,625
3,118
2,393
2,204
1,305
1,160
burst
23,204
19,144
15,952
14,500
12,472
9,572
8,816
5,220
4,640
Min. bend
radius
Weight
mm
lb/ft
100
125
180
205
240
300
420
500
630
0.24
0.33
0.41
0.45
0.59
0.97
1.52
1.75
2.22
13
REV 62116
B
HYDRAULIC HOSES
R2ATHT
TWO WIRE BRAID HIGH TEMP.
Construction
Applications
Inner Tube:
Hydraulic system service with petroleum,
Exceeds SAE J 517 (SAE 100R2AT)
High temp. elastomer rubber, resistant to oil.
fire resistant and water base fluids, fuel and
EN 853 2SN
lubricating systems.
Former DIN 20022 2SN (part 4)
Temperature Range:
Approvals:
-40°F up to +302°F
MSHA
except: air not to exceed 249°F
FRAS AS1180.10B &13A
Reinforcement:
Cover:
Blue elastomer rubber resistant to abrasion, oils,
: water not to exceed 158°F
Limitations:
RUBBER HOSE
to conduct air above 246 psi.
Impulse Testing:
All sizes tested to 200,000 cycles (hose only).
Hose Tails:
PIRTEK SAE 100 R2 AT — DIN EN 853 2SN “HIGH TEMP” 1” (25mm) R2ATHT-16 2494 PSI (172 BAR) WORK.PRESS: 302°F MAX MSHA-25 FRAS AS1180.10B & 13A
Lay line example: White text on dark blue. Comment: Lay line example may not be a true indication of current status. Refer to PIRTEK for current information.
Product
Code
14
B
Nominal Diameter
OD mm
Pressure PSI
Min. bend
radius
Weight
R2ATHT-04
DN
6
inch
1/4
mm
6.4
Wire
12.7
Cover
15.2
working
5,743
burst
22,974
mm
102
lb/ft
0.27
R2ATHT-06
10
3/8
9.5
16.7
19.2
5,004
20,015
127
0.39
R2ATHT-08
12
1/2
12.7
19.8
22.1
4,250
16,998
178
0.46
R2ATHT-10
16
5/8
15.9
23.0
25.1
3,249
12,995
203
0.54
R2ATHT-12
19
3/4
19.0
27.0
29.5
3,002
12,009
241
0.67
R2ATHT-16
25
1
25.4
34.9
37.8
2,494
9,978
305
0.97
R2ATHT-20
31
1 1/4
31.8
44.5
48.8
2,248
8,992
419
1.61
R2ATHT-24
38
1 1/2
38.1
50.8
54.6
1,740
6,962
508
1.74
R2ATHT-32
51
2
50.8
63.5
67.8
1,494
5,975
635
2.27
REV 62116
HYDRAULIC HOSES
JH70
JACKING HOSE
Construction
Applications
Inner Tube:
High pressure hose for hydraulic fluids including
ISO 1307
mineral and vegetable oil in hydraulic systems
for jacking applications.
Approvals: MSHA Approval No. IC-215/0
Temperature Range:
Limitations:
Only for use as jacking hose.
Reinforcement:
Cover:
+257°F intermittent
Note reduced Safety Factor at 2:1
Hose Tails: PIRTEK ‘K’ Series NM1E-0404K,
NM1E-0604K & NM1E-0606K
REFER to M.A.P.S. for WORK INSTRUCTION.
SPECIAL NOTES: Use ONLY NM1E-0404K, NM1E-0604K & NM1E-0606K Hose Tails and fit SRP Strain Relivers. Safety Factor is 2:1
PIRTEK JACKING HOSE JH70-04 6.4mm (1/4”) 700 BAR (10152 PSI) MSHA IC-215/0 ABRASION RESISTANT
Lay line example: Red text on black. Comment: Lay line example may not be a true indication of current status. Refer to PIRTEK for current information.
Product
Code
Nominal Diameter
JH70-04
DN
6
inch
1/4
mm
6.4
JH70-06
10
3/8
9.5
Reinforcement
OD mm
Pressure PSI
Min. bend
radius
Weight
2 braid
Cover
14.8
working
10,150
burst
20,300
mm
80
lb/ft
0.25
2 braid
19.0
10,150
20,300
95
0.38
RUBBER HOSE
Use in conjunction with SRP Strain Relievers.
NOTE: Hose End Fittings: Use ONLY NM1E-0404K, NM1E-0604K & NM1E-0606K
JH70-06 assembly with Strain
Reliever attached to resist kinking of
the hose at the end of the Ferrule
SRP-04 Strain Reliever
SRP-06 Strain Reliever
15
REV 62116
B
HYDRAULIC HOSES
C21
ISOBARIC CLASS HOSE
Construction
Applications
Inner Tube: Seamless synthetic rubber, resistant Isobaric (constant 3,045 psi working pressure
to oil.
JIS K6349-3
across all sizes) hose for hydraulic fluids such as
mineral and vegetable oils, aqueous emulsions,
Approvals:
Reinforcement: 4 spirals of high tensile steel
water and inert gases.
MSHA Approval No. IC-104/1 PAR No. 84844
wire.
FRAS AS1180.10B & 13A
Cover: Abrasion resistant black synthetic rubber
Impulse Testing:
resistant to oils, ozone and weathering.
inner liner.
Tested in accordance with SAE 100 R12
requirements.
Temperature Range:
RUBBER HOSE
PIRTEK ‘J’ Series
PIRTEK C21-32 2” (50 mm) 3,045 PSI (210 BAR) MSHA IC-104/1 ABRASION RESISTANT
C21-32
B
Hose Tails:
Product
Code
16
Nominal Diameter
DN
51
inch
2”
OD mm
mm
50.8
Wire
63.6
Cover
66.7
Pressure PSI
working
3,045
burst
12,180
Min. bend
radius
Weight
mm
500
lb/ft
42.82
Performance
Standard
SAE
R12
REV 62116
HYDRAULIC HOSES
C25
ISOBARIC CLASS HOSE
Construction
Applications
Meets or exceeds SAE J 517 (100 R16).
to oil.
Meets or exceeds EN 857 2SC.
Tested in accordance with SAE J517, EN856,
Reinforcement: Two braids of high tensile steel
AS3791.
wire, or 4 spirals of high tensile steel wire.
Approvals:
Cover: Abrasion resistant black synthetic
SAE J1942
PVC nitrile rubber resistant to oils, ozone and
inner liner.
MSHA Approval No. IC-104/3 PAR
weathering.
HF Type B
No. 84844 applies to all sizes
Temperature Range:
FRAS AS1180.10B & 13A
Impulse Testing:
Braided hoses as per SAE 100 R16.
Spiral hoses as per SAE 100 R12.
RUBBER HOSE
Braided Hoses:
Hose Tails:
PIRTEK C25 1” (25.4 mm) 3625 PSI (250 BAR) MSHA FRAS
HF TYPE B ABRASION RESISTANT
Product
Code
C25-16
Nominal Diameter
DN
25
inch
1
mm
25.4
Type
2 braid
OD mm
Wire
32.9
Cover
35.6
Pressure PSI
working
3,625
burst
14,504
Min. bend
radius
Weight
mm
250
lb/ft
0.87
17
REV 62116
B
HYDRAULIC HOSES
C45
ISOBARIC CLASS HOSE
Construction
Applications
Inner Tube: Synthetic rubber, resistant to oil.
High pressure hose for hydraulic fluids such as
mineral oils, aqueous emulsions, vegetable oils,
specifications:
water, air and inert gases.
DIN EN 856 4SH
wire.
Especially used for “Dynapac” style rollers.
NOTE: THIS HOSE MUST ONLY BE USED FOR Approvals:
STATIC APPLICATIONS – Not recommended for
impulsing applications.
MSHA Approval No. IC-188
Hose Tails:
(2-piece system requires a separate SFB ferrule)
RUBBER HOSE
-40°F up to +158°F ambient
PIRTEK CLASS 45 C45-10 15.9mm (5/8”) 450 BAR (6525 PSI) MSHA
Lay line example: Orange text on black. Comment: Lay line example may not be a true indication of current status. Refer to PIRTEK for current information.
C45-10
B
PIRTEK ‘B’ Series
Product
Code
18
Temperature Range:
Nominal Diameter
DN
16
inch
5/8
mm
15.9
Reinforcement
4 spiral
O.D.
Cover
mm
28.5
Pressure PSI
working
6,525
burst
26,100
Min. bend
radius
Weight
mm
250
lb/ft
0.87
REV 62116
ISOBARIC CLASS HOSE
Construction
Applications
Meets or exceeds SAE J 517 (100 R12, R13 or
to oil.
R16)
Meets or exceeds EN 857 2SC.
Tested in accordance with SAE J 517, EN856,
wire, or 4-6 spirals of high tensile steel wire.
AS3791.
fluids at temperatures above 70°F will allow wire
Cover: Abrasion resistant black synthetic
Approvals:
PVC nitrile rubber resistant to oils, ozone and
inner liner.
SAE J1942
HYDRAULIC HOSES
C35
HF Type B
MSHA Approval No. IC-104/1
weathering.
PAR No. 84844 on all sizes
Spiral hoses:
FRAS AS1180.10B & 13A
RUBBER HOSE
Temperature Range:
Impulse Testing:
Braided hoses as per SAE 100 R16 & R12
Spiral hoses as per SAE 100 R13
Braided hoses:
Hose Tails:
PIRTEK ‘K’, ‘J’ Series 1/2”
PIRTEK ‘H’ Series 2”
PIRTEK Interlock Series 1 1/4” and above
PIRTEK CLASS 35-08 1/2” (12.7 mm) 5076 PSI (350 BAR) MSHA FRAS
Lay line example: White text on braided hose. Comment: Lay line example may not be a true indication of current status. Refer to PIRTEK for current information.
Product
Code
C35-05
C35-06
C35-08 *
C35-10 †
C35-12
C35-16
C35-20
C35-24
C35-32 *
Nominal Diameter
DN
8
10
12
16
19
25
31
38
51
inch
5/16
3/8
1/2
5/8
3/4
1
1 1/4
1 1/2
2
mm
7.9
9.5
12.7
16.1
19.2
25.6
32.2
38.5
51.2
OD mm
Type
Wire
13.0
15.3
20.1
23.7
28.1
35.6
45.6
52.5
68.1
2 braid
2 braid
2 braid
4 spiral
4 spiral
4 spiral
6 spiral
6 spiral
6 spiral
Cover
14.7
17.2
22.2
27.4
30.7
38.7
48.7
55.6
71.1
Pressure PSI
working
5,510
5,076
5,076
5,076
5,076
5,076
5,076
5,076
5,076
burst
22,040
20,305
20,305
20,305
20,305
20,305
20,305
20,305
20,305
Min. bend
radius
Weight
mm
85
90
130
200
220
280
380
480
600
lb/ft
0.23
0.28
0.42
0.67
1.01
1.48
2.49
2.96
4.64
† Meets or exceeds SAE100 R12 except for reinforcement OD
*Note: C35-08 and C35-32 is only included in SAE J1942
HF Type B
19
REV 62116
B
HYDRAULIC HOSES
C42
ISOBARIC CLASS HOSE
Construction
Applications
Tested in accordance with SAE J517, EN856,
to oil.
AS3791
Approvals:
wire (C42-04), or 4-6 spirals of high tensile steel
wire.
(C42EH-32 has MSHA Approval IC-8/13)
FRAS AS1180.10B & 13A
inner liner.
Impulse Testing:
resistant to oils, ozone and weathering (PVC
nitrile rubber on braided hoses).
RUBBER HOSE
Temperature Range:
Braided hoses as per SAE 100 R16
Spiral hoses:
Spiral hoses as per SAE 100 R12, R15
C42EH 2 Million Cycles applicable only in
conjunction with EH Series interlock tails.
Hose Tails:
Braided hoses:
PIRTEK ‘H’ Series1 1/4 to 1 1/2”
Interlock 1 1/4” to 1 1/2”
PIRTEK CLASS C42-12 3/4” (19 mm) 6091 PSI (420 BAR) MSHA IC-104/3 ABRASION RESISTANT
Lay line example: White text on braided hoses. Yellow text on spiral hoses. Comment: Lay line example may not be a true indication of current status.
Refer to PIRTEK for current information.
Product
Code
C42-04
C42-06
C42-08
C42-10
C42-12
C42-16
C42-20
C42-24
C42-32
20
B
Nominal Diameter
DN
6
10
12
16
19
25
31
38
51
inch
1/4
3/8
1/2
5/8”
3/4
1
1 1/4
1 1/2
2
mm
6.4
9.7
12.9
16.0
19.2
25.7
32.2
38.5
51.2
OD mm
Type
2 braid
4 spiral
4 spiral
4 spiral
4 spiral
4 spiral
6 spiral
6 spiral
6 spiral
Wire
12.7
17.2
20.7
24.4
28.1
35.1
46.8
54.0
70.6
Pressure PSI
Cover
14.9
20.2
23.8
26.4
32.0
38.2
49.8
57.2
75.0
working
6,091
6,091
6,091
6,091
6,091
6,091
6,091
6,091
6,091
burst
24,364
24,364
24,364
24,364
24,364
24,364
24,364
24,364
24,364
Min. bend
radius
Weight
mm
75
125
180
140
280
300
400
500
600
lb/ft
0.27
0.47
0.60
0.67
1.01
1.48
2.62
3.16
5.32
REV 62116
HYDRAULIC HOSES
PC25
PIRTEK CLASS HOSE
Construction
Applications
Inner Tube:
Isobaric (constant 3,626 psi working pressure
Seamless synthetic rubber, oil resistant.
specifications:
mineral oils, aqueous emulsions, water, air and
SAE 100R16 (braided hose)
inert gases. Excellent compact bend radius
SAE 100R12 (spiral hose)
Temperature Range:
Approvals:
Cover:
Spiral hoses:
SAE J1942
High abrasion resistance black synthetic rubber
MSHA IC 104/3
Reinforcement:
Two braids, or 4 spirals of high tensile steel wire.
HF Type B
inner liner.
Hose Tails:
PIRTEK ‘J’ Series 3/4”
PIRTEK ‘J’ Series 1 1/4”, 1 1/2”
PIRTEK PC25-12 3/4” (19 MM) 3625 PSI (250 BAR) MSHA FRAS
RUBBER HOSE
Braided hoses:
Product
Code
PC25-10
PC25-12
PC25-20
PC25-24
Nominal Diameter
DN
16
20
32
40
inch
5/8
3/4
1 1/4
1/2
mm
15.9
19.1
31.8
38.1
Reinforcement
OD
(mm)
2 braid
2 braid
4 spiral
4 spiral
26.0
29.1
44.9
52.4
Pressure PSI
W.P.
3,625
3,625
3,625
3,625
Min. Burst
14,500
14,500
14,500
14,500
Min. bend
radius
Weight
mm
140
170
280
330
lb/ft
0.56
0.64
1.58
2.06
21
REV 62116
B
HYDRAULIC HOSES
PC35
PIRTEK CLASS HOSE
Construction
Applications
Inner Tube:
specifications:
SAE R16 (braided hose)
inert gases. Excellent compact bend radius
SAE 100 R12 (spiral hose)
Reinforcement:
Two braids, 4spirals or 6 spirals of high tensile
SAE 100 R13 / R15 (spiral hose)
Temperature Range:
steel wire.
Approvals:
SAE J1942
High abrasion resistant black synthetic rubber
MSHA IC 104/3
RUBBER HOSE
Spiral hoses:
Cover:
HF Type B
Braided hoses:
Prolonged usage with water or water based fluids at
temperatures above 158°F will allow wire corrosion
as a result of diffusion through the inner liner.
Hose Tails:
PIRTEK ‘K’ Series 5/8”
PIRTEK ‘H’ Series 1 1/4” to 1 1/2”
PIRTEK Interlock Series 1 1/4” to 1 1/2”
PIRTEK CLASS PC35-12 3/4” (19 MM) 5076 PSI (350 BAR) MSHA FRAS
Product
Code
PC35-06
PC35-10
PC35-12
PC35-16
PC35-20
PC35-24
22
B
Nominal Diameter
DN
10
16
20
25
32
40
inch
3/8
5/8
3/4
1
1 1/4
1 1/2
mm
9.5
15.9
19.1
25.4
31.8
38.1
Reinforcement
O.D.
mm
2 braids
4 spirals
4 spirals
4 spirals
6 spirals
6 spirals
18.9
26.4
29.0
36.6
48.7
55.6
Pressure PSI
W.P.
5,076
5,076
5,076
5,076
5,076
5,076
Min. Burst
20,305
20,305
20,305
20,305
20,305
20,305
Min. bend
radius
Weight
mm
90
140
170
220
280
330
lb/ft
0.37
0.67
0.76
1.34
2.55
3.09
REV 62116
HYDRAULIC HOSES
PC42
PIRTEK CLASS HOSE
Construction
Applications
Inner Tube:
specifications: SAE 100 R16 (braided hose)
Reinforcement:
inert gases. Excellent compact bend radius.
Approvals:
SAE J1942
HF Type B
Cover:
Spiral hoses:
High abrasion resistance black synthetic rubber
Braided hoses:
inner liner.
Hose Tails:
PIRTEK ‘K’ Series 1/4”
PIRTEK ‘H’ Series 1 1/2”
PIRTEK ‘I’ Series 1 1/2”
PIRTEK CLASS PC42-04 1/4” (6.4 MM) 6091 PSI (420 BAR) MSHA FRAS
RUBBER HOSE
Temperature Range:
Product
Code
PC42-04 *
PC42-24
Nominal Diameter
DN
6
40
inch
1/4
1 1/2
*Note: PC42-04 is only included in SAE J1942
mm
6.4
38.1
Reinforcement
OD
(mm)
2 braids
6 spiral
14.9
55.6
Pressure PSI
W.P.
6,091
6,091
Min. Burst
24,364
24,364
Min. bend
radius
Weight
mm
70
330
lb/ft
0.26
3.16
HF Type B
23
REV 62116
B
HYDRAULIC HOSES
P42
FOUR WIRE SPIRAL HOSE
Construction
Applications
Inner Tube: Synthetic rubber, resistant to oil.
mineral oils, aqueous emulsions, vegetable oils,
specifications: DIN EN 856 4SP
water.
Approvals:
wire.
Temperature Range:
MSHA Approval No. IC 84/19
Hose Tails:
RUBBER HOSE
24
B
PIRTEK P42-10 DN 16 5/8” EXCEEDS EN 856 4SP-SAE 100R12 W,P 420-6000 PSI MSHA
Product
Code
P42-10
Nominal Diameter
DN
16
inch
5/8
mm
15.9
Reinforcement
4 spiral
O.D.
Cover
mm
27.2
Pressure PSI
working
6,000
burst
24,000
Min. bend
radius
Weight
mm
230
lb/ft
0.69
REV 62116
LARGE BORE HOSE
Construction
Applications
Inner Tube: Seamless synthetic
SAE J517 except for reinforcement OD
rubber, resistant to oil.
such as mineral and vegetable oils, aqueous
emulsions and water.
Approvals:
Reinforcement: Four spirals of high
tensile steel wire.
fluids at temperatures above 58°F will allow wire
FRAS AS1180.10B & 13A
HYDRAULIC HOSES
JBF
Hose Tails: PIRTEK
inner liner.
‘BSMS’ Series
Temperature Range:
32°F up to +158°F water
-40°F up to +158°F air / ambient
PIRTEK JUMBO ACE 63mm (2 1/2”) JBF-40 140 BAR (2030 PSI) WP MSHA IC/104/1 FRAS ABRASION RESISTANT
Lay line example: Light yellow text on black. Comment: Lay line example may not be a true indication of current status. Refer to PIRTEK for current information.
Product
Code
JBF-40
Nominal Diameter
DN
63
inch
2.1/2
mm
63.5
Type
4 spiral
OD mm
Cover
82.4
Pressure PSI
working
2,030
burst
8,120
Min. bend
radius
mm
660
Weight
lb/ft
3.69
Test
Impulses
No.
500,000
RUBBER HOSE
25
REV 62116
B
HYDRAULIC HOSES
LPG
LP GAS AS1869 CLASS D
Construction
Applications
Inner Tube:
High pressure hose for transfer of natural
Meets and / or exceeds:
Conductive Teflon®.
gas, town gas, LPG, and butane-propane on
AS1869 Class D
stationary and mobile LPG gas engines. Ideal
Very low extractables and permeation rate.
Reinforcement:
for forklift, automotive, light & medium duty truck
Single braid of stainless steel wire.
and transfer.
Approvals:
AGA (Aust. Gas Association)
Cover:
Temperature Range:
Black and blue fire retardant, abrasion resistant
-4°F up to +257°F
Hose Tails:
aramid polyester.
PIRTEK ‘G’ Series
Special procedures apply using dedicated dies
RUBBER HOSE
and spacers.
Thermoplastic tag required on all hose
assemblies.
Product
Code
LPG-06
LPG-10†
Nominal Diameter
DN
10
16
inch
5/16
1/2
mm
7.9
12.7
Reinforcement
OD
(mm)
1 wire braid
1 wire braid
13.6
19.1
Pressure PSI
W.P.
377
377
Min. Burst
1508
1508
Min. bend
radius
Weight
mm
101.6
165.1
lb/ft
0.12
0.18
† Limited stock available
26
B
REV 62116
HYDRAULIC HOSES
R12C
SPIRAL SAE100 R12 HOSE
Construction
Applications
Inner Tube: Fabric reinforced synthetic rubber,
SAE J 517 (100 R12)
resistant to oil.
glycol, mineral oils, fuels, hydrocarbons etc.
EN 856 R12
Designed for applications where flexibility and
Reinforcement: Four spirals of high tensile steel
high temperature resistance are required.
Approvals:
wire separated by layers of synthetic rubber.
Compatible with Caterpillar® reusable fittings.
US MSHA IC-101
Cover: Black synthetic rubber resistant to
Temperature Range:
Impulse Testing:
abrasion, oils, ozone and weathering.
1,000,000 impulses @ 133% of working pressure
for all sizes. Additionally, hose is aged by heating
and cooling prior to testing, hose only.
PIRTEK ‘J’ or ‘X’ Series 3/4” or upwards
XT® Technology SAE 100R12 ¾” Max WP 4000psi MSHA IC-101/10 Made in USA
Lay line example: Yellow text on black. Comment: Lay line example may not be a true indication of current status. Refer to PIRTEK for current information.
Product
Code
R12C-06
R12C-08
R12C-10
R12C-12
R12C-16
R12C-20
R12C-24
R12C-32
Nominal Diameter
DN
10
12
16
19
25
31
38
51
inch
3/8
1/2
5/8
3/4
1
1.1/4
1.1/2
2
mm
9.5
13
16
19
25
32
38
51
Type
4 spiral
4 spiral
4 spiral
4 spiral
4 spiral
4 spiral
4 spiral
4 spiral
OD mm
Wire
17.2
20.7
24.6
27.6
34.9
43.9
50.4
63.6
Cover
20.2
23.8
27.2
30.7
38
47
53.4
66.7
Pressure PSI
working
4,000
4,000
4,000
4,000
4,000
3,002
2,495
2,495
burst
16,000
16,000
16,000
16,000
16,000
12,009
9,979
9,979
Min. Bend
Radius
mm
64
89
102
121
153
210
254
318
RUBBER HOSE
Hose Tails:
Weight
lb/ft
0.47
0.56
0.81
0.96
1.34
1.88
2.28
2.86
27
REV 62116
B
HYDRAULIC HOSES
R13C
SPIRAL SAE100 R13 HOSE
Construction
Applications
Inner Tube: Fabric reinforced synthetic rubber,
Very high pressure hose for hydraulic fluids such
SAE J 517 (100 R13)
resistant to oil.
as glycol, mineral oils, fuels, hydrocarbons etc.
EN 856 R13
Specifically designed for applications where
Reinforcement: Four or six spirals of high
high pulsating pressure, flexibility and high
Approvals:
tensile steel wire separed by layers of synthetic
temperature resistance are required. Compatible
US MSHA IC-101
rubber.
with Caterpillar® reusable fittings.
Cover: Black synthetic rubber resistant to
Temperature Range:
1 000 000 impulses @ 120% of working pressure
abrasion, oils, ozone and weathering.
for all sizes. Additionally, hose is aged by heating
Impulse Testing:
and cooling prior to testing, hose only.
RUBBER HOSE
Hose Tails:
PIRTEK ‘X’ Series all sizes
Interlock option 1 1/4” upwards
XT® Technology SAE 100R13 1” Max WP 5000psi MSHA IC-101/10 Made in USA
Lay line example: Red text on black. Comment: Lay line example may not be a true indication of current status. Refer to PIRTEK for current information.
Product
Code
R13C-12
R13C-16
R13C-20
R13C-24
R13C-32
28
B
Nominal Diameter
DN
19
25
31
38
51
inch
3/4
1
1.1/4
1.1/2
2
mm
19
25
32
38
51
OD mm
Type
4 spiral
4 spiral
6 spiral
6 spiral
6 spiral
Wire
29.0
35.6
46.8
54.3
68.1
Cover
32.1
38.7
49.8
57.3
71.1
Pressure PSI
working
5,000
5,000
5,000
5,000
5,000
burst
20,000
20,000
20,000
20,000
20,000
Min. Bend
Radius
mm
141
153
210
254
318
Weight
lb/ft
1.18
1.55
2.49
3.12
4.64
REV 62116
MEDIUM PRESSURE THERMOPLASTIC
HOSE
Construction
Applications
Inner Tube:
Medium pressure hydraulic and pneumatic
SAE J517
Smooth seamless thermoplastic polyester.
service. For hydraulic and pneumatic circuits
Construction
and systems found on agricultural, industrial,
SAE 100R7 - EN855
Reinforcement:
and construction equipment. Ideal for use at
Note: REFER to chemical resistance table at the
Polyester fiber braid.
low temperature on fork trucks in refrigerated
back of this section for compatibility.
warehouses and has an excellent bend radius.
Cover:
Vacuum Rating:
Black non perforated antiabrasion polyurethane,
Temperature Range:
-13.5 psi (27.5 in Hg)
stabilized to UV rays.
-65°F up to +212°F
Safety Factor 4:1
Cutting:
fire resistant fluids.
Hand Cutting is recommended for this hose.
Hose Tails:
PIRTEK T Series
PIRTEK® TPR7-06 3/8” (9.7 mm) W.P. 2537 PSI (175 BAR)
TPR7-02
TPR7-03
TPR7-04
TPR7-05
TPR7-06
TPR7-08
Nominal ID
DN
3
5
6
8
10
12
inch
1/8
3/16
1/4
5/16
3/8
1/2
OD
mm
3.5
4.8
6.4
8.0
9.7
13.0
mm
8.5
10.0
11.8
14.3
16.0
20.3
Pressure PSI
working
3,335
3,045
2,900
2,755
2,537
2,030
min burst
13,340
12,180
11,600
11,020
10,150
8,120
Min bend
radius
Weight
mm
25
30
35
45
55
75
lb/ft
.038
.049
.060
.086
.10
.15
THERMOPLASTIC HOSE
Max +158°F with air, water, water based fluids or
Product
Code
HYDRAULIC HOSES
TPR7
29
REV 62116
B
HYDRAULIC HOSES
TPR7X2
MEDIUM PRESSURE THERMOPLASTIC
HOSE
Construction
Applications
Inner Tube:
Medium pressure hydraulic and pneumatic
SAE J517
service. For hydraulic and pneumatic circuits
Construction
and systems found on agricultural, industrial,
SAE 100R7 - EN855
Reinforcement:
and construction equipment. Ideal for use at
low temperature on fork trucks in refrigerated
warehouses and has an excellent bend radius.
Cover:
Temperature Range:
-13.5 psi (27.5 in Hg)
-65°F up to +212°F
Safety Factor 4:1
THERMOPLASTIC HOSE
B
Cutting:
Hose Tails:
PIRTEK T Series
PIRTEK® TPR7X2-06 3/8” (9.7 mm) W.P. 2537 PSI (175 BAR)
Product
Code
TPR7X2-02
TPR7X2-03
TPR7X2-04
TPR7X2-05
TPR7X2-06
TPR7X2-08
30
Vacuum Rating:
Nominal ID
DN
3
5
6
8
10
12
inch
1/8
3/16
1/4
5/16
3/8
1/2
OD
mm
3.5
4.8
6.4
8.0
9.7
13.0
mm
8.5
10.0
11.8
14.3
16.0
20.3
Pressure PSI
working
3,335
3,045
2,900
2,755
2,537
2,030
min burst
13,340
12,180
11,600
11,020
10,150
8,120
Min bend
radius
Weight
mm
25
30
35
45
55
75
lb/ft
.038
.049
.060
.086
.10
.15
REV 62116
NON-CONDUCTIVE THERMOPLASTIC
HOSE
Construction
Applications
Inner Tube:
General hydraulic systems that
ANSI A92.2 for Vehicle Mounted Aerial Devices
may contact high voltage sources.
SAE J517 Non-conductive hose
Aerial equipment
Construction SAE 100R7
Reinforcement:
Mobile hydraulics
Rescue apparatus and tools
Flexible at low temperatures and has an
Vacuum Rating:
excellent bend radius.
Cover:
-13.5 psi (27.5 in Hg)
Orange non perforated antiabrasion
Temperature Range:
polyurethane, stabilized to UV rays.
Safety Factor 4:1
Cutting:
THERMOPLASTIC HOSE
-40°F up to +212°F
Hose Tails:
PIRTEK T Series
PIRTEK® TPR7NC-06 NON-CONDUCTIVE 3/8” (9.7 mm) W.P. 2537 PSI (175 BAR)
Product
Code
TPR7NC-03
TPR7NC-04
TPR7NC-05
TPR7NC-06
TPR7NC-08
Nominal ID
DN
5
6
8
10
12
HYDRAULIC HOSES
TPR7NC
inch
3/16
1/4
5/16
3/8
1/2
OD
mm
4.8
6.4
8.0
9.7
13.0
mm
10.0
11.8
14.3
16.0
20.3
Pressure PSI
working
3,045
2,900
2,755
2,537
2,030
min burst
12,180
11,600
11,020
10,150
8,120
Min bend
radius
Weight
mm
30
35
45
55
75
lb/ft
.049
.06
.086
.10
.15
31
REV 62116
B
HYDRAULIC HOSES
TPR8
HIGH PRESSURE THERMOPLASTIC
HOSE
Construction
Applications
Inner Tube:
High pressure general hydraulic systems,
SAE 100R8 performance with R7 dimensions
Smooth seamless thermoplastic polyamide.
polyols, solvents and compatible gasses.
Note:
Suitable for tank to tank ONLY oxygen and
Refer to chemical resistance table at the back of
Reinforcement:
breathing air mixtures. Not recomended for use
this section for compatibility.
Two leayers of polyester braid.
over the sheave.
Vacuum Rating:
Cover:
Temperature Range:
-13.5 psi (27.5 in Hg)
-65°F up to +212°F
Safety Factor 4:1
THERMOPLASTIC HOSE
Hose Tails:
PIRTEK T Series
PIRTEK® TPR8-06 3/8” (9.7 mm) W.P. 4060 PSI (280 BAR)
Product
Code
TPR8-04
TPR8-06
TPR8-08
32
B
Cutting:
Nominal ID
DN
6
10
12
inch
1/4
3/8
1/2
OD
mm
6.4
9.7
13.0
mm
11.8
16.0
20.3
Pressure PSI
working
5,075
4,060
3,552
min burst
20,300
16,240
14,210
Min bend
radius
Weight
mm
50
70
95
lb/ft
.056
.094
.146
REV 62116
HYDRAULIC HOSES
TPR8NC
NON-CONDUCTIVE THERMOPLASTIC
HOSE
Construction
Applications
Inner Tube:
General hydraulic systems that
SAE J517 Non-conductive hose
Smooth seamless thermoplastic polyamide.
may contact high voltage sources.
Construction
Aerial equipment
SAE 100R8
Reinforcement:
Mobile hydraulics
Note: Refer to chemical resistance table at the
Rescue apparatus and tools
Flexible at low temperatures and has an
Cover:
Vacuum Rating:
excellent bend radius.
Orange non perforated antiabrasion
-13.5 psi (27.5 in Hg)
Temperature Range:
polyurethane, stabilized to UV rays.
Safety Factor 4:1
Cutting:
THERMOPLASTIC HOSE
-65°F up to +212°F
Hose Tails:
PIRTEK T Series
PIRTEK® TPR8NC-06 3/8” (9.7 mm) W.P. 4060 PSI (280 BAR)
Product
Code
TPR8NC-04
TPR8NC-06
TPR8NC-08
Nominal ID
DN
6
10
12
inch
1/4
3/8
1/2
OD
mm
6.4
9.7
13.0
mm
11.8
16.0
20.3
Pressure PSI
working
5,075
4,060
3,552
min burst
20,300
16,240
14,210
Min bend
radius
Weight
mm
50
70
95
lb/ft
.057
.090
.151
33
REV 62116
B
HYDRAULIC HOSES
TP1W
ONE WIRE THERMOPLASTIC HOSE
Construction
Applications
Inner Tube:
TP1W LOW TEMPERATURE series
These hoses meet or exceed standards:-
hoses have been created for hydraulic use at
SAE 100 R1AT - EN 853 1ST,
high pressure. Suitable for gas transfer. This
1SN - EN 857 1SC pressures
Reinforcement:
hose is particularly recommended on mobile
One layer of high tensile steel braid.
hydraulic equipment including lift trucks
Vacuum Rating:
• Refer to chemical resistance
-13.5 psi (27.5 in Hg)
Cover:
table at the back of this section .
Cutting:
Black perforated antiabrasion polyurethane,
THERMOPLASTIC HOSE
34
B
stabilized to UV rays, resistant to micro-
Temperature Range:
organisms and good protection against
-65°F up to +212°F
hydrolysis .
Max 158°F with air, water, water
Hose Tails:
based fluids or fire resistant fluids. T series
Smooth blade recommended for cutting.
PIRTEK TP1W-08 1/2” (12.7 mm) W.P. 2755 P.S.I. (190 BAR)
Product
Code
TP1W-03
TP1W-04
TP1W-05
TP1W-06
TP1W-08
Nominal ID
OD
Pressure PSI
Min bend
radius
Weight
DN
inch
mm
mm
working
min burst
mm
lb/ft
5
6
8
10
12
3/16
1/4
5/16
3/8
1/2
4.8
6.4
8.0
9.7
13.0
10.0
11.9
14.0
16.0
19.2
4,712
4,350
3,480
3,262
2,755
18,850
17,400
13,920
13,050
11,020
30
40
50
60
75
0.09
0.11
0.15
0.18
0.22
REV 62116
HYDRAULIC HOSES
TP1WX2
ONE WIRE THERMOPLASTIC HOSE
Construction
Applications
Inner Tube:
TP1W LOW TEMPERATURE series
These hoses meet or exceed standards:-
hoses have been created for hydraulic use at
SAE 100 R1AT - EN 853 1ST,
high pressure. Suitable for gas transfer. This
1SN - EN 857 1SC pressures
Reinforcement:
hose is particularly recommended on mobile
One layer of high tensile steel braid.
hydraulic equipment including lift trucks
Vacuum Rating:
• Refer to chemical resistance
-13.5 psi (27.5 in Hg)
Cover:
table at the back of this section.
Cutting:
Black perforated antiabrasion polyurethane,
stabilized to UV rays, resistant to micro-
Temperature Range:
organisms and good protection against
-65°F up to +212°F
hydrolysis.
Max 158°F with air, water, water
Hose Tails:
based fluids or fire resistant fluids . T series
Smooth blade recommended for cutting.
PIRTEK TP1WX2-08 1/2” (12.7 mm) W.P. 2755 P.S.I. (190 BAR)
Product
Code
TP1WX2-03
TP1WX2-04
TP1WX2-05
TP1WX2-06
TP1WX2-08
Nominal ID
OD
Pressure PSI
Min bend
radius
Weight
DN
inch
mm
mm
working
min burst
mm
lb/ft
5
6
8
10
12
3/16
1/4
5/16
3/8
1/2
4.8
6.4
8.0
9.7
13.0
10.0
11.9
14.0
16.0
19.2
4,712
4,350
3,480
3,262
2,755
18,850
17,400
13,920
13,050
11,020
30
40
50
60
75
0.09
0.11
0.15
0.18
0.22
THERMOPLASTIC HOSE
35
Rev 4
REV 62116
B
HYDRAULIC HOSES
100STH
PTFE (TEFLON) HOSE
Construction
Applications
Inner Tube:
Medium pressure and laundry equipment
SAE 100 R14
extruded seamless smooth bore Teflon.
Plastic moulding presses
Reinforcement:
Hazardous chemicals
Additional Options: A graphite impregnated
Steam and compressor discharge
(black) Teflon liner is available to special order
AISI 304 stainless steel single wire braid.
Cover:
for applications requiring a core tube capable
Temperature Range:
of safely conducting static electricity. Consult
-65°F up to +446°F* (see notes below)
PIRTEK for details.
Comment:
Impulse Testing:
No lay line present due to the stainless steel
No information available.
The reinforcement braid serves as the outer
cover.
THERMOPLASTIC HOSE
braid.
Hose Tails:
PIRTEK ‘T’ Series
Product
Code
Nominal ID
in
3/16
Average
OD
Wall
Thickness
mm
7.6
mm
0.762
working
3,000
Min bend
radius
Vacuum
Service
min burst
12,000
mm
51
hg
28.90
Pressure PSI
STH-03
Braiding
1 Braid
mm
4.8
STH-04
1 Braid
6.35
1/4
9.4
0.762
3,000
12,000
59
28.90
STH-05
1 Braid
7.94
5/16
10.2
0.762
2,500
10,000
99
28.90
STH-06 +
1 Braid
9.5
3/8
12.5
0.762
2,250
9,000
55
28.90
STH-08 +
1 Braid
12.7
1/2
14.9
0.762
1,750
7,000
135
28.90
STH-10 +
1 Braid
15.9
5/8
20.3
0.762
1,500
6,000
165
15.00
STH-12 +
1 Braid
19.05
3/4
22.1
0.762
1,100
4,400
190
15.00
STH-16 +
2 Braid
25.4
1
29.2
0.762
900
3,600
270
13.00
+ Use of an internal support coil for hoses -06 and larger is recmmended for tube support where continuous or extended service at high temperature
together with low or negative pressure is expected
Not recommended for steam / cold water cycling
*For temperatures above 248°F
Pressure: Reduce working pressure by 1% per additional degree F.
Vacuum: Reduce vacuum rating by 1.5% per additional degree F.
Note: The minimum bend radius quoted is for a static bend at ambient temperature.
Dynamic bending, especially at elevated temperatures, will increase the
minimum bend radius accordingly. Consult PIRTEK for specific applications
36
B
REV 62116
HYDRAULIC HOSES
TECHNICAL DATA
SUMMARY OF PIRTEK HYDRAULIC HOSE MATERIALS
C21
C25
C35
C42
C45
PC25
PC35
PC42
R1AT
R1ATFS
R2AT / 2SC
R2ATHT
100R5
Description
Liner Material
Cover Material
210 bar four spiral hose
250 bar four spiral hose
350 bar braid or spiral hose
420 bar braid or spiral hose
450 bar spiral hose high flexibility
High abrasion resistance 250 bar hose
One wire braid hose
One wire fire suppression hose
Two wire braid hose
High Temp. two wire braid hose
Engine & air brake hose
NBR (Class I)
NBR (Class I)
NBR (Class I)
NBR (Class I)
NBR (Class I)
NBR (Class I)
NBR (Class I)
NBR (Class I)
NBR (Class I)
NBR (Class I)
NBR (Class I)
NBR (Class IV)
NBR (Class I)
NBR (Class I)
NBR (Class I)
NBR (Class I)
NBR (Class I)
NBR (Class I)
NBR (Class I)
NBR (Class I)
NBR (Class I)
NBR (Class I)
NBR (Class I)
NBR (Class I)
NBR (Class IV)
Fiber
NBR (Class IV)
Polyester
Hydraulic Suction Delivery
NBR (Class I)
NBR (Class I)
R4HT
High Temp. Hydraulic Suction / Delivery
NBR (Class IV)
NBR (Class IV)
R12C
SAE 100R12 spiral hose
NBR (Class II)
NBR (Class II)
R13C
SAE 100R13 spiral hose
NBR (Class II)
NBR (Class II)
MPH
Multi-purpose oil and air hose
NBR (Class I)
NBR (Class I)
JH70
Jacking Hose
NBR (Class I)
NBR (Class I)
JBF
Large bore four spiral hose
NBR (Class I)
NBR (Class I)
LPG
Liquid Petroleum Approved Hose
Teflon®
NBR (Class I)
TPR7
General purpose SAE 100R7
Polyester
Polyurethane
TPR7X2
General purpose twinline SAE 100R7
Polyester
Polyurethane
Non-Conductive SAE R7
Polyester
Polyurethane
1 Wire Thermoplastic
Polyester
Polyurethane
1 Wire Thermoplastic twinline
Polyester
Polyurethane
High Pressure compact SAE R8
Polyamide (Nylon)
Polyurethane
High Pressure non-conductive SAE R8
Polyamide (Nylon)
Polyurethane
Stainless steel braid over Teflon®
Teflon®
Stainless steel
TPR7NC
TP1W
TP1WX2
TPR8
TPR8NC
STH
THERMOPLASTIC
High Temp. Air Brake Hose
100R4
TECHNICAL DATA
R5HT
Type
RUBBER
Product Code
37
REV 62116
B
HYDRAULIC HOSES
TECHNICAL DATA
CHEMICAL RESISTANCE TABLE
CAUTION
The data in the following pages has been compiled from generally available sources and should not
be relied upon without consulting and following the specific recommendations of the manufacturers of
particular products
The data is considered valid at 20°F (70°F) except where specified otherwise. Chemical compatibility
can vary greatly with temperature
A good rating does not necessarily indicate the suitability of a particular hose and chemical
combination due to variables such as improper clamp and coupling application, special hose
construction, gasket material etc. Nor does it imply compliance with relevant food standards or safety
standards that may be applicable
SOLVENT INFORMATION
TECHNICAL DATA
Aromatic solvents: benzene, cumene, p-cumene, naphthalene, toluene, xylene, cresol, styrene, cyclohexane
and combinations
Aliphatic solvents: propane, butane, pentane, hexane, heptane, dipetene, tripropylene
Halogenous solvents: chloroform, dichorobenzene, dichloroethylene, methylen bromide, methylen chloride,
benzyl chloride, carbon tetrachloride, trichloroethylene, carbon disulphite, turpentine, perchloroethylene,
dichloroethane
Ketonic solvents: acetone, methyl ketone, isobutyl ketone, methyl ethyl ketone, methyl isobutyl ketone
Esters solvents: butyl acetate, methyl acetate, anyl acetate, isobutyl acetate
Amines: aniline, ethylene diamine , diethanol amine, triethanolamine, dimethyl amine, monoethanolamine
Alcohols: methanol, ethanol, propanol, butanol, glycerol
Common
Elastomers
ASTM
Designation
B
General Properties
brominated butyl
chlorinated butyl
BIIR
CIIR
bromo isobutene-isoprene
chloro isobutene-isoprene
excellent weathering resistance, low permeability to
air and gases, good physical properties, resistant to heat
poor resistance to petroleum based fluids, good resistance to fat
chlorinated
polyethylene
CM (CPE)
chloro polyethylene
excellent ozone and weathering resistance, good oil and chemical
resistance, excellent flame resistance
cross-linked
polyethylene
XLPE
UHMWPE
polyethylene
and cross linking agent
excellent for a very wide range of solvents, chemicals,
acids and oils
ethylene
propylene
EPDM
ethylene propylene
diene-terpolymer
excellent ozone, chemical and ageing resistance, poor resistance to
petroleum based fluids, very good steam resistance
ethylene
propylene
EPM (EPR)
ethylene propylene
copolymer
excellent ozone, weathering, heat, chemical and aging resistance,
poor resistance to petroleum products, very good steam resistance
hypalon ®
CSM
chloro-sulfonylpolyethylene
excellent weathering, ozone and acid resistance, good heat and
abrasion resistance, fair resistance to petroleum based fluids
natural
NR
isoprene natural
excellent physical properties, very good abrasion resistance, poor
resistance to petroleum based fluids
neoprene
CR
chloroprene
good weathering and flame retardant resistance,
good oil reistance, good physical properties
nitrile (buna-n)
NBR
Acrylonitrile-butadiene
excellent petroleum products resistance, moderate resistance to
aromatics, good physical properties
acrylonitrile-butadiene /
polyvinyl-chloride
excellent petroleum products and weathering resistance,
both for tube and cover
buna-n /
PVC / NBR
polyvinyl chloride
38
Composition
polyacrylic
ACM
acrylic monomer
excellent oil and tar resistance at high temperatures
sbr
SBR
styrene butadiene
good physical properties, good abrasion resistance,
poor resistance to petroleum based fluids
viton ®
FKM
fluorocarbon rubber
excellent high temperature resistance, particularly in air and oil, very
good chemical resistance
REV 62116
C
U
U
U
U
G
C
U
C
G
C
G
U
U
U
C
U
U
U
G
U
U
C
U
C
G
C
C
U
G
-
C
U
G
-
PVC
U
G
-
G
G
G
G
G
U
G
U
G
G
G
U
G
C
G
G
C
U
G
G
G
-
-
Polyurethane
U
C
U
G
C
C
G
C
U
G
U
G
G
G
C
G
U
G
G
C
C
G
G
G
G
-
U
U
C
U
C
C
C
U
U
U
C
U
C
G
U
-
Polyester
U
U
G
C
U
G
U
C
C
C
C
G
U
G
G
C
C
G
G
G
G
-
U
G
G
C
C
G
G
U
G
U
G
-
Nylon
U
G
G
U
G
U
U
G
U
G
G
G
G
G
G
C
G
G
G
G
G
G
G
G
-
Barium Salts
Barium Sulphate
Barium Sulphide
Basic Copper Arsenate
Beer
Beet Sugar Liquors
Benzaldehyde
Benzene (Benzol)
Benzenesulphonic Acid
Benzine
Benzine (Petroleum Ether)
Benzine (Petroleum Naphtha)
Benzoic Acid
Benzyl Alcohol
Benzyl Benzoate
Benzyl Chloride
Biodiesel < 92c
Biodiesel > 92c
Bismuth Carbonate
Black Sulphate Liquor
Blast Furnace Gas
Borac Acid
Borax
Bordeaux Mixture
Boric Acid
Boric Copper Sulphate
Brake Oil, Dot 3
Brake Oil, Dot 4
Brake Oil, Dot 5
Brine
Bromine
Bunker Oil
ButAdiene
Butane
Butter Oil
Butyl Acetate
Butyl Alchol (Butanol)
Butyl Amine
Butyl Carbitol
Butyl Cellosolve
Butyl Mercaptan
Butyl Stearate
Butylene (Butene)
Butyraldehyde
Butyric Acid
Calcium Acetate 10% Aq
Calcium Arsenate
Calcium Bisulphate 10% Aq
Calcium Bisulphide
Calcium Bisulphite
Calcium Carbonate
Calcium Chlorate
Calcium Chloride 10% Aq
Calcium Hydroxide 10% Aq
Calcium Hypochlorite 10% Aq
Calcium Nitrate 10% Aq
Calcium Salts
Calcium Silicate
Calcium Sulphate
Calcium Sulphide
Teflon
C
C
U
U
U
U
G
U
U
U
U
-
Class V
C
G
G
G
C
C
U
U
U
G
Class IV
U
U
U
U
U
C
C
U
G
G
G
U
G
C
C
C
U
U
G
Class III
U
C
C
U
C
-
U
G
G
C
G
U
G
C
C
G
U
U
G
THERMOPLASTIC
Class II
G
U
-
U
U
U
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
C
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
Legend:
G = Good
C = Conditional
U = Unsatisfactory
No Data
RUBBER
Class I
C
C
C
C
C
C
C
PVC
C
C
Polyurethane
U
C
C
C
Polyester
Class V
-
Nylon
Class IV
U
U
U
Teflon
Class III
G
G
C
C
U
C
G
G
C
G
G
U
U
C
G
-
AGENT
G
G
G
G
C
C
G
G
G
G
G
G
G
G
G
G
G
G
C
C
C
G
G
G
G
G
G
G
G
G
G
G
G
G
G
C
G
G
G
G
C
C
U
G
G
G
G
G
G
G
G
G
-
G
G
G
C
U
C
G
G
G
G
U
G
C
G
G
G
G
C
C
G
-
G
G
G
C
U
C
G
G
G
G
U
G
C
G
G
G
G
C
C
G
-
G
G
U
U
G
C
C
G
G
G
C
G
U
G
G
C
G
G
G
G
-
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
TECHNICAL DATA
Acetaldehyde
Acetic Acid, Glacial
Acetic Acid, Less Than 10%
Acetic Acid, Over 10%
Acetic Anhydride
Acetone
Acetophenone
Acetyl Acetone
Acetyl Bromide
Acetyl Chloride
Acetylene
Acrylonitrile
Air (Under 20kgf/Cm2)
Alcohols
Aluminium
Aluminium Acetate
Aluminium Bromide
Aluminium Chloride
Aluminium Fluoride 20%
Aluminium Hydroxide
Aluminium Nitrate 10% Aqueous
Aluminium Salts
Aluminium Sulphate
Aluminium Sulphate
Alums
Ammonia Gas, Cold
Ammonia Gas, Hot
Ammonia, Aq
Ammonia, Liquid (Anhydrous)
Ammonium Carbonate
Ammonium Chloride
Ammonium Hydroxide
Ammonium Metaphosphate
Ammonium Nitrate
Ammonium Nitrite
Ammonium Phosphate
Ammonium Sulphate
Ammonium Thiocyanate
Amyl Acetate
Amyl Alchol
Amyl Chloride
Amyl Chloronapthalene
Amyl Napthalene
Anethole
Aniline
Aniline Dyes
Aniline Hydrochloride
Animal Oils
Antirnony Salts
Apoclor Monsanto (Chlorinated Hydrocarbon)
Aqua Regia
Aromatic Hydrocarbons
Arsenic Acid
Arsenic Salts
Askarel
Asphalt <105 C
Automatic Transmission Fluid (ATF)
Barium Carbonate
Barium Chloride
Barium Hydroxide
THERMOPLASTIC
Class II
Legend:
G = Good
C = Conditional
U = Unsatisfactory
No Data
RUBBER
Class I
AGENT
HYDRAULIC HOSES
TECHNICAL DATA CHEMICAL RESISTANCE TABLE
39
REV 62116
B
U
U
C
C
U
U
G
U
U
-
PVC
G
U
G
G
G
-
Polyurethane
G
C
C
Polyester
C
G
G
G
Nylon
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
U
G
G
G
G
G
G
G
G
G
G
G
G
Decalin
Denatured Alcohol
Detergent / Water Solution (Conc)
Diacetone
Diacetone Alcohol
Diammonium Phosphate
Dibenzyl Ether
Dibutyl Ether
Dibutyl Phthalate
Dibutyl Sebacate
Dichlorobenzene
Diesel Fuel
Diesel Oil Light
Diethanolamine (20% Conc.)
Diethyl Ether
Diethyl Phthalate
Diethyl Sebacate
Diethylamine
Diethylene Glycol
Di-Isobutylene
Di-Isopropyl Ketone
Dimethyl Aniline
Dimethyl Formamide
Dimethyl Phthalate
Dioctyl Phosphate
Dioctyl Phthalate (Dop)
Dioxane
Dipentene
Dowtherm A and E
Enamels
Essential Oils
Ethanol
Ethanolamine
Ether
Ethyl Acetate
Ethyl Acetoacetate
Ethyl Acrylate
Ethyl Alchol (Ethanol)
Ethyl Benzene
Ethyl Cellulose
Ethyl Chloride
Ethyl Ether
Ethyl Mercaptan
Ethyl Pentochlorobenzene
Ethyl Silicate
Ethylene Cellulose
Ethylene ChlorhydrIn
Ethylene Chloride
Ethylene Diamine
Ethylene Dichloride
Ethylene Glycol
Ethylene Oxide
Fatty Acid
Ferric Chloride
Ferric Chloride
Ferric Nitrate
Ferric Nitrate 10% Aq
Ferric Sulphate 10% Aq
Ferrous Chloride
Ferrous Nitrate
Teflon
U
U
U
G
C
G
G
G
C
G
C
U
U
C
U
C
G
U
U
C
G
G
G
G
G
G
G
G
C
C
C
G
G
U
-
Class V
G
G
G
G
G
-
U
C
C
G
U
C
C
C
C
C
C
U
U
G
U
U
C
U
U
U
G
G
C
G
G
G
G
G
U
U
U
G
C
G
G
-
Class IV
G
G
C
C
-
U
C
C
G
U
C
C
C
C
C
C
U
U
G
U
U
U
U
U
U
G
G
C
G
G
G
G
G
U
U
U
C
C
G
G
-
THERMOPLASTIC
Class III
U
U
G
U
G
U
G
-
U
G
G
G
G
G
G
G
C
G
C
G
G
G
G
U
C
U
G
U
G
G
G
G
C
G
G
G
U
U
U
G
C
G
G
-
Legend:
G = Good
C = Conditional
U = Unsatisfactory
No Data
RUBBER
Class II
U
G
U
C
U
U
U
G
U
C
U
U
U
U
U
U
C
U
U
G
G
U
U
-
G
AGENT
Class I
G
U
C
G
G
U
U
PVC
C
U
G
U
G
U
U
G
U
C
U
U
U
U
U
U
Polyurethane
-
Polyester
G
-
Nylon
Class V
G
U
C
U
C
U
U
U
U
G
G
C
C
-
Teflon
Class IV
Caliche Liquors (Chile Saltpetre)
Cane Sugar Liquors
Carbitol
Carbolic Acid (Phenol)
Carbon Bisulfide
Carbon Dioxide
Carbon Disulphide
Carbon Monoxide
Carbon Tetrachloride
Carbonates
Carbonic Acid
Castor Oil
Caustic Potash (<20%)
Caustic Potash (>20%)
Caustic Soda (Sodium Hydroxide) <20%
Caustic Soda (Sodium Hydroxide) >20%
Cellosolve Acetate
Cellosolve Butyl
Cellulubes Celanese (Phosphate Ester Base)
Cellusolves Union Carbide
China Wood Oil (Tung)
Chlordane
Chlorinated Solvents
Chlorine Gas, Dry
Chlorine Gas, Wet (<20%)
Chlorine Trifluoride
Chloroacetic Acid
Chloroacetone
Chlorobenzene
Chlorobromomethane
Chloroform
Chloronapthalene
Chlorosulphonic Acid
Chlorotoluene
Chromic Acid 30%
Chromium Salts
Cider
Citric Acid
Coal Gas
Cod Liver Oil
Coke Oven Gas
Compressed Air (< 290 Psi or 2000 Kpa)
Copper Chloride
Copper Chloride 10% Aq
Copper Cyanide 10% Aq
Copper Sulphate 10% Aq
Corn Oil
Corn Syrup
Cottonseed Oil
Creosote Oil
Cresol
Cresylic Acid
Crude Petroleum Oil
Crude Wax
Cupric Sulphate
Cutting Oil White & Bagley No. 2190
Cyclohexane
Cyclohexanol
Cyclohexanone
Cymene
THERMOPLASTIC
Class III
Legend:
G = Good
C = Conditional
U = Unsatisfactory
No Data
RUBBER
Class II
TECHNICAL DATA
B
AGENT
Class I
HYDRAULIC HOSES
40
C
-
G
G
G
C
C
U
G
C
C
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
U
G
U
U
U
U
G
G
G
G
-
C
U
G
U
G
G
U
-
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
U
G
G
G
G
C
G
-
C
C
C
G
C
C
C
C
G
G
C
C
C
C
U
U
U
G
C
G
G
-
C
U
C
G
C
C
C
C
G
G
C
C
C
C
U
U
U
C
C
G
G
-
U
G
C
C
U
U
G
G
C
C
U
C
U
U
U
G
G
G
G
-
G
U
G
G
U
G
G
G
G
G
G
G
G
REV 62116
Polyester
Polyurethane
PVC
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
Nylon
G
G
G
G
G
Hydrogen Peroxide, Dilute
Hydrogen Sulphate, Gaseous
Hydrogen Sulphide, Dry
Hydrogen Sulphide, Wet
Hydrogluosilic Acid
Hydrolube Union Carbide (Hydraulic Fluid Water Glycol Base)
Irus Shell 902 Hydraulic Fluid
(Water-Oil Emulsion)
Iso Octane
Isobutyl Alcohol
IsocyanAtes
Isopropyl Acetate
Isopropyl Alcohol
Isopropyl Ether
Jp-4, Jp-5
Kerosene
Ketones
Lacquer
Lacquer Solvents
Lactic Acid
Lard
Lead Acetate
Lead Arsenate
Lead Sulphate
Lead Tetramethyl
Light Oil
Lime
Lime Sulphur
Linoleic Acid
Linseed Cake
Linseed Oil
Linseed Oil
Liquefied Petroleum Gas (LPG)
Lubricating Oils, Diester Base
Lubricating Oils, Petro Base
Magnesium Chloride 10%Aq
Magnesium Hydroxide 10%Aq
Magnesium Sulphate 10%Aq
Maleic Acid
Mercuric Chloride
Mercury
Mesityl Oxide
Methane
Methy Salicylate
Methyl Acetate
Methyl Alcohol (Methanol)
Methyl Bromide
Methyl Chloride
Methyl Ethyl Ketone (MEK)
Methyl Formate
Methyl Isopropyl Ketone
Methyl Methacrylate
Methyl Sulphate
Methylene Chloride
Methylisobutylketone (MIBK)
MIL-H-46170
MIL-H-5606
MIL-H-6083
MIL-H-83282
Teflon
C
C
C
G
C
C
G
C
C
G
G
C
C
C
G
G
G
G
G
G
C
C
C
U
U
U
G
G
G
G
C
G
C
Class V
U
C
C
U
U
U
C
U
C
G
G
G
G
C
G
G
G
G
G
G
G
G
C
G
G
G
C
G
C
G
G
C
U
G
U
Class IV
G
C
U
G
G
G
G
U
G
G
G
G
U
U
U
U
G
G
C
C
G
G
G
G
G
U
U
C
U
C
G
G
G
G
C
C
G
G
G
G
G
G
G
G
G
G
G
G
C
G
C
C
G
U
U
G
U
Class III
U
C
U
G
U
C
C
G
G
U
U
G
U
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
U
U
G
U
THERMOPLASTIC
Class II
C
C
G
G
-
-
G
Legend:
G = Good
C = Conditional
U = Unsatisfactory
No Data
RUBBER
Class I
G
U
U
U
G
U
G
-
C
C
U
G
G
G
G
C
U
G
G
U
G
U
G
C
G
C
U
U
C
-
PVC
U
G
Polyurethane
U
C
Polyester
Class V
-
Nylon
Class IV
U
U
U
C
-
Teflon
Class III
C
G
C
C
C
C
C
G
G
AGENT
C
G
-
U
U
U
U
-
C
U
-
G
-
G
G
G
G
-
G
C
-
G
C
-
G
-
G
G
-
-
-
-
-
-
-
G
C
G
G
G
U
C
G
G
G
G
G
G
-
C
U
U
U
-
-
G
G
G
G
-
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
C
G
G
G
G
-
G
C
G
C
C
G
G
G
G
G
G
G
G
C
G
C
G
C
G
G
G
C
C
U
U
C
G
C
-
G
C
G
C
C
G
G
G
G
G
G
G
G
C
G
C
G
C
G
G
G
C
C
U
U
C
G
C
-
U
C
U
U
G
G
G
G
G
G
G
G
G
G
G
G
C
G
U
U
U
U
U
U
U
-
G
G
G
U
C
G
C
G
C
U
-
U
U
G
C
G
G
U
U
U
G
G
G
G
G
G
G
G
U
U
U
C
G
G
G
G
G
G
U
U
-
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
-
TECHNICAL DATA
Ferrous Salt Solutions
Ferrous Sulphate
Fluoboric Acid
Fluoboric Acid
Fluorine
Fluorosilicic
Formaldehyde
Formic Acid
Freon 12 (Refrigerant)
Fruit Juices
Fuel Oil
Fuel Oil (Aromatic Gas) 100 Octane
Fuel Oil (Aromatic Gas) 100 Octane
Fumaric Acid
Furan Furfuran
Furfural
Furfuryl Alcohol
Galic Acid (< 20%)
Gas (Natural)
Gas Oil
Gaseous Hydrogen
Gasohol
Gasoline
Gasoline (Aromatic)
Gasoline (Nor-Aromatic)
Gelatine
Glucose
Glue (Depends On Type)
Glycerine, Glycerol
Glycol To Wc
Grease,Petroleum
Green Sulphate Liquor
Heavy Water (D20)
Helium
Heptane
Hexaldehyde
Hexane
Hexene
Hexyl Alcohol
Hydraulic Oil Phos. Ester Blend (MIL L-7808)
Hydraulic Oil, Auto Transmission Fluid
Hydraulic Oil, Chlorine Base
Hydraulic Oil, Ester Blend
Hydraulic Oil, Ordinary Petro
Hydraulic Oil, Phosphate Ester (FR)
Hydraulic Oil, Silicone Oil
Hydraulic Oil, Sodium Silicate Base
Hydraulic Oil, Water & Petrol Emulsion (FR)
Hydraulic Oil, Water Glycol (85c)
Hydraulic,Oil, Water & Oil Emulsion
Hydrobromic Acid
Hydrochloric Acid V%
Hydrocyanic Acid
Hydrofluoric Acid, Cold
Hydrofluoric Acid, Hot
Hydrofluorsilic Acid
Hydrogen (Gaseous)
Hydrogen Peroxide, Concentrated
THERMOPLASTIC
Class II
Legend:
G = Good
C = Conditional
U = Unsatisfactory
No Data
RUBBER
Class I
AGENT
HYDRAULIC HOSES
41
REV 62116
B
G
U
U
C
U
G
G
G
G
G
G
C
G
G
G
G
G
C
G
G
G
G
G
U
U
G
U
U
C
G
C
U
U
U
U
U
-
C
G
U
G
G
U
U
U
U
U
G
C
G
G
G
C
G
U
U
U
U
PVC
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
-
Polyurethane
G
G
-
G
U
G
U
U
U
U
U
U
U
U
-
Polyester
G
G
G
G
G
G
G
G
G
G
-
G
U
C
G
G
C
G
G
C
G
G
G
U
Nylon
G
G
G
Potassium Permanganate (5%. Conc.)
Potassium Sulphate
Propane
Propyl Acetate
Propyl Alcohol
Pydraul (Stauffer) F-9,150, 600, 625
Pyrethrum
Pyridine
Red Oil
Salt Water (Sea Water)
Saturated Steam
Sewage
Silicone Oils
Silver Nitrate
Skydrol Monsanto 500, 7000
Soap Solutions
Soda (Sodium Carbonate)
Soda Water
Sodium Acetate 10% Aq
Sodium Bicarbonate 10% Aq
Sodium Bisulfite
Sodium Bisulphate
Sodium Borate
Sodium Carbonate
Sodium Chloride Solutions
Sodium Cyanide
Sodium Hydroxide <10%
Sodium Hydroxide 40%
Sodium Hypochloride 10%
Sodium Hypochlorite
Sodium Metaphosphate 10% Aq
Sodium Nitrate 10% Aq
Sodium Perborate 10% Aq
Sodium Peroxide 10% Aq
Sodium Phosphates 10% Aq
Sodium Silicate 10% Aq
Sodium Sulphate 10% Aq
Sodium Sulphide
Sodium Sulphite 10% Aq
Sodium Thiosulphate (Hypo) 10% Aq
Solution 2-4D DDT Preparation Hydroxy Quinoline
Soybean Oil
Stannic Chloride
Stannous Chloride
Steam
Steam
Stearic Acid
Stearic Acid, Botanical
Stearin
Stoddard Solvent
Styrene
Sucrose Solution
Sulphur
Sulphur
Sulphur Chloride
Sulphur Dioxide
Sulphur Trioxide
Sulphuric Acid, 10%, Hot
Sulphuric Acid, 10%. Cold
Sulphuric Acid, 75%, Cold
Teflon
G
G
G
U
U
U
G
G
G
U
G
C
G
C
G
G
C
C
G
C
C
C
G
G
C
C
G
G
G
C
G
Class V
G
G
G
G
C
C
G
U
C
U
G
G
G
G
C
C
G
G
C
G
G
U
U
G
C
U
G
U
U
G
U
G
Class IV
U
U
U
U
G
-
G
G
G
G
C
C
U
G
U
C
U
G
G
G
G
C
C
G
G
C
G
G
U
U
G
C
U
C
U
U
G
U
G
THERMOPLASTIC
Class III
U
U
C
U
G
U
-
-
G
G
G
G
G
G
U
G
C
C
G
G
G
G
G
G
G
G
G
G
G
G
U
G
G
G
U
C
G
C
G
C
G
Legend:
G = Good
C = Conditional
U = Unsatisfactory
No Data
RUBBER
Class II
U
U
U
U
G
G
AGENT
Class I
G
U
G
U
U
U
U
U
U
U
-
PVC
G
G
G
G
U
G
G
G
G
U
U
U
G
U
U
C
U
C
U
G
U
U
U
U
U
U
G
G
G
G
G
-
Polyurethane
-
Polyester
U
C
U
U
U
U
U
U
U
C
U
Nylon
Class V
G
C
G
U
C
G
G
G
G
-
Teflon
Class IV
Milk
Mil-L-2104
Mil-L-23699
Mil-L-7808
Mineral Oils
Molasses
Monochlorobenzene
Mustard
Naphtalene
Naphtha
Napthenic Acid
Natural Gas
Nickel Acetate 10% Aq
Nickel Chloride
Nickel Sulphate
Nicotine
Nitric Acid (Conc)
Nitric ACid (Dil)
Nitriuc Acid (Red, Fuming)
Nitrobenzene
Nitrogen / Argon Gaseous
Nitrous Oxide
Octyl Alcohol
Oil
Oil Of Turpentine
Oleic Acid
Oleum Spirits
Olive Oil
Ortho-Dichlorobenzene
OS 45 Monsanto Hyd. Fluid (Silicate Ester Base)
Oxalic Acid
Oxygen (Liquid)
Oxygen Gaseous
Ozone
Paint (Oil Based)
Paint Solvents (Oil Base)
Palmlitic Acid
Peanut Oil
Pentane
Perchloric Acid
Perchloroethylene
Petroleum Oils (Refined)
Petroleum Oils (Sour)
Phenol (Carbolic Acid)
Phenolates
Phenols (Carbolic Acid)
Phosphate Ester Base Oil
Phosphoric Acid (70%)
Phosphoric Acid 10%
Picric Acid (Molten)
Picric Acid (Solution)
Pine Oil
Pinene
Plating Solution, Chrome
Potassium Acetate 10% Aq
Potassium Chloride
Potassium Cyanide
Potassium Dichromate
Potassium Hydroxide (Potash)
Potassium Nitrate
THERMOPLASTIC
Class III
Legend:
G = Good
C = Conditional
U = Unsatisfactory
No Data
RUBBER
Class II
TECHNICAL DATA
B
AGENT
Class I
HYDRAULIC HOSES
42
G
G
G
G
G
G
G
U
G
G
G
G
C
G
G
G
G
G
G
G
G
G
G
G
C
G
G
G
G
G
G
G
C
U
G
G
G
G
G
U
C
C
-
U
G
G
C
G
C
G
U
G
G
G
G
G
G
G
G
C
C
G
G
G
G
G
G
G
U
G
G
U
C
G
U
U
U
-
U
G
G
C
G
G
G
U
G
G
G
G
G
G
G
G
C
C
G
G
G
G
G
G
G
U
C
G
U
C
G
U
U
U
-
G
G
G
U
G
U
G
U
G
G
C
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
U
G
C
G
C
G
G
-
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
REV 62116
PVC
G
G
U
-
Polyurethane
G
C
G
G
U
G
G
Polyester
G
G
-
G
U
U
-
Nylon
G
C
C
C
U
U
U
G
G
G
G
U
U
U
-
Teflon
U
U
U
U
U
G
U
-
Class V
U
U
U
Class IV
U
G
-
Class III
U
U
U
G
G
U
G
U
-
THERMOPLASTIC
G
G
G
G
G
G
G
G
G
G
U
U
G
G
G
G
G
G
U
G
G
G
G
U
U
C
G
G
C
C
C
U
U
C
C
G
U
U
C
G
G
C
C
C
U
U
C
C
G
U
C
G
G
G
U
U
U
C
C
U
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
U
U
C
C
U
G
C
G
G
G
C
C
G
C
C
G
C
U
G
C
G
G
G
C
C
G
C
C
G
G
G
U
G
G
G
G
U
U
G
G
G
G
G
G
G
G
TECHNICAL DATA
Sulphuric Acid, 95%, Cold
Sulphurous Acid
Tannic Acid
Tar
Tartaric Acid
Terpineol
Toluene
Toluol
Transformer Oil
Transmission Fluid Type A
Tributoxyethyl Phosphate
Tributyl Phosphate
Trichloracetic Acid
Trichlorethylene
Tricresyl Phosphate
Trisodium Phosphate Solution
Tung Oil (China Wood Oil)
Turpentine Oil
Ucon Union Carbide
(Hydraulic Fluid Water Glycol Base)
Urea
Uric Acid
Varnish
Vegetable Greases
Versilube
Vinegar
Vinyl Chloride
Water @ 65°C
Water Glycol
Water, Normal Temp
Whiskey
White & Bagley No. 2190 Cutting Oil
Wine
Wool Oil
Xylene
Xylol
Zinc Acetate
Zinc Chloride 10% Aq
Zinc Hydrate
Zinc Sulphate 10% Aq
Class II
Legend:
G = Good
C = Conditional
U = Unsatisfactory
No Data
RUBBER
Class I
AGENT
HYDRAULIC HOSES
43
REV 62116
B
HYDRAULIC HOSES
TECHNICAL DATA
44
B

Hose Catalog

Transcription

Similar documents

Mineflex Brochure - Reel Easy

GOLDENHORN 12S

Napa Unicoil sellsheet Dealer copy.indd

where quality and price meet head-on

Professional Grade Products Available Through Your

DEPAC DEPAC Auto-Dynamic Load (ADL) Control System:

ST 120 LT - Kanaflex

UNICOIL Hose Bender Flyer

RYCO 24•7

TSB 33