BIFOLD HANGAR DOORS

BI-FOLD BARDUVA HANGAR DOORS
Technical Information
BIFOLD
HANGAR
DOORS
BARDUVA APPRECIATE THE QUALITY!
Product datasheet
BI-FOLD BARDUVA HANGAR DOORS
Technical Details
Features
Max size: (W / H)*:
18000/10000 mm
Construction:
Constructed of steel tubing and Cold-formed
steel structural members (Painted RAL 9002)
Lifting belts:
Width – 75 mm, thickness – 3 mm.
Truss:
Steel tube - 80 x 80 x 3 mm (painted).
Side lock:
Mechanical, locks the fully closed door and the gate does not
move in the high winds.
Control unit:
Supplied Voltage for motors - 380V, control unit - 220V
3 buttons on the control unit (open-stop-close).
Seals:
Doors are furnished with a header seal and bottom
loop that hugs the contour of the Ground
Safety devices:
Built-in brake on the engine.
Operation:
Standard: Electrical operator
Doors up to 18 meters long are delivered in a twin-motor version with belt drums.
Additional**: You can order additional feature - door moves with a push of a button and
you do not need to keep the button pressed. With this feature , photocell sensors must be
installed. Sensors are installed on side guide rails, near the floor, to stop the doors in case
of any obstacle. Also an Electric sensing edge that reverses the door in the event it
* Bigger sizes available on request
**Optional
Operating Performance
Operating speed:
0.08m/s
Differential pressure (Wind Load):
0.7—1.6kPa class 3 –5, EN 12424
Sound Reduction (standard):
15dB Rw (ISO 717)
Water resistance:
0.11kPa for closed Door class 2, EN 13241)
Operating environment:
-35°C to +70°C
2
Product datasheet
BI-FOLD BARDUVA HANGAR DOORS
General Information
Quality is our highest priority. We want our customers to know that in the big doors market Barduva is the company providing
the high quality BIFOLD hangar doors at very reasonable prices.
Developments in new technologies, agricultural machinery, bigger and bigger storage buildings are constructed, hangars, which
needs to close entry-exit gates, to protect property from the weather conditions. Whatever that is, hangar for the industry, building for agricultural machinery or any other commercial project. Decision is clear – BIFOLD Hangar doors.
Basic structural and functional
components

Leaf frame (1)

Hinges (2)

Side door locks (3)

Truss (4)

Bearing mounting plates with bearing (5)

Rolling belt drums (6)

Shaft (7)

Electromechanical transmission (8)

Supporting bearing (9)

Control unit (10) (Not shown)

The safety and warning devices; Panel – heat insulation (12)(Not Shown)
Figure 1
2
1
3
4
7
5
8
9
3
6
Product datasheet
BI-FOLD BARDUVA HANGAR DOORS
BI-FOLD Description

Construction: Constructed of steel tubing and
Figure 2
Cold-formed steel structural members

Door finish: According to customer preferences:
insulation panels, aluminum profiles with polycarbonate glass, tin by RAL, etc..

Lifting belts: Belts: width 75mm, thickness – 3mm.

Truss: steel tube – 80x80x3mm

Opening speed: 0.08m/s (up to 2 minutes)

Wind load Pressure: 0.7 – 1.6 kPa depending on
size (Class 3 – 5, EN12424) Higher wind loads on
request.

Side locks: Standard auto-locks automatically Lock
and unlock the door as it opens And closes with a
push of a button

Power operator: Supplied voltage: 308V for motors and 220V for the control unit.

Control box: Momentary contact, 3-button controls (Up/Down/Stop) standard

OPTIONAL CONTROL: Door moves with a push of a button and you do not need to keep the button pressed. With this
future photocell sensors must be installed. Sensors are installed on side guide rails, near the floor, to stop the doors in case
of any obstacle. Manual emergency controls.

SECURITY DEVICES: build – in brake on the engine. And contact sensor in side the bottom rubber shield.
Operation principle
A solid steel drive shaft that runs continuously for the full width of the door, wraps the belts on the drums and the folding door
structure is raised. The shaft with the drums is attached to the door frame near the bottom.
Opening Procedure
While holding the door on-off switch, which is located on the control unit, electromechanical drives turns shaft and at the same
time belts attached to drums begins to raise the gates. Side locks, mounted on a door frame on both sides, embraces the gates
and they start to rise. Gate rises to the top with the help of lifting straps and the upper end rigidly attached to the upper lintel.
When doors reaches the predetermined height of the opening dis-connectors on the electromechanical drives stops them.
Closure Procedure
While holding the door on-off switch, which is located on the control unit, electromechanical drive loosens shaft, cables became loose and lifting belts allows the doors to move slowly downward. After landing, side locks presses and fixates doors to
the building , thereby ensuring the security and stability of the gate
Whole doors perimeter is sealed with rubber. Because of the dense, doubled rubber seal with the cloth inside, doors becomes
resistant to any weather conditions!
The chain drive motor located in the aid, in case of power failure or breakdown of the door electromechanical actuators can lift
or lower doors manually. For such situations there is dedicated emergency release lever and emergency lifting chain.
4
Product datasheet
BI-FOLD BARDUVA HANGAR DOORS
Door leaf Construction
Hinges
The door leaf is deviated in two sections, top section and bot-
Heavy duty Hinges are welded on the door. The number&
tom section. Both sections are constructed of appropriately-
size of hinges varies with door size and wind load require-
sized steel tubing and cold-formed steel structural members
ments. The Top hinges are provided with bolt holes and can
based on the size and wind load.
be bolted or welded to the supporting structure.
A door frame as it is shown on figure 1 with a size of 18x8.2m,
L&R end Door Hinges
will be 620x78
will be deliver at your place in 4 smaller section which they
will be bolt-together by our engineers.
Hinges
Center door
Hinges 310x78
Building Frame
Typical structural beam
side section and a top
steel tube header
Belt System
The door structure is raised by a special polyester lifting
belts (each one's breaking point is 10,000 kg). Lifting belts at
the bottom of the door are wrapped on the drum in several
places evenly over the entire frame of the gate, that gates
would open evenly and easy.
Belts never entangles, nor makes noise, nor rust (as opposed
to of steel cables). Door lifting belts are perhaps the most
important advantage, because you don't need pulleys - less
parts, less problems, less maintenance! Lifting belts are made
Belt Drum
of polyester material, so it is durable and reliable.
Lifting Belts
5
Product datasheet
BI-FOLD BARDUVA HANGAR DOORS
Operating System
The Bi-fold door is always supplied with an electrical operat-
Manual operation handler
ing system, a control unit and two or more electromechanical
drives, depending on the door size/weight. The motors are
Gearbox
placed on the base of the bottom frame section.
The door is opened by an impulse from the three-button door
controller.
Electric motor
Figure 3
Drive shaft
The shaft is mounted on the bottom panel and runs continuously along the entire width of the door in order to properly
support the system. The drive shaft is driven from the gear
reducers by a dual chain drive system and at the same time
belts attached to drums begins to raise or lower the gates. The
shaft is galvanized to prevent corrosion.
Drive shaft
Door closed
Door fully opened
Door opening
Depending on
door size
6
BI-FOLD BARDUVA HANGAR DOORS
Figure 4
Side locking
mechanism
Figure 5
Belt Drums
Motor with
Gearbox
Shaft
Bearing mounting plates
with bearing
7
Product datasheet
BI-FOLD BARDUVA HANGAR DOORS
Guide Rollers
Weather Seals
Barduva uses only the highest quality parts in the market.
Whole doors perimeter is sealed with rubber. Because
Precision sealed Spherical Roller Bearings are installed at
of the dense, doubled rubber seal with the cloth inside,
the bottom of doors at jamb column locations. These bear-
doors becomes resistant to any weather conditions!
ings can absolve much more loading pressure and work
Motor box
longer than the any other bearing in the market.
The motors are sealed with a metallic box, for safety.
Figure 6
Motor inside
Guide Rollers
Bifold Hangar Door Electronic Safety Systems:
1. The upper door height switch switches off electric current when ascending gates reaches the
highest point of the opening
2. Side locks, does not let the doors to move and protects against high wind loads while they are
in a locked position.
3. 3 buttons control system (up/down/stop). Two buttons located on control unit allows the gate
to move up or down by pressing and holding them until gate rises or descend.
4. Photo electric cell sensor is mounted near the floor to stop the doors in the event of any obstacle. In case of an obstacle at the range of photo electric sensor (object, human, vehicle etc.)
doors won't descend. (optional function).
5. Warning light and sound signal is needed to alert people at the door operation area. This security system is particularly recommended for doors that will be equipped with a radio remote
control or other remote controls (optional function).
8
Product datasheet
BI-FOLD BARDUVA HANGAR DOORS
DOOR TRUSSES
There are many ways to strength a bifold door.
Barduva Hangar Doors are provided with an
extra Heavy Duty Truss.
Depending on the door size and wind load requirements we provide two types of trusses,
internal or external, in order to avoid bending's
on your door.
A - INTERNAL TRUSS
Most of the doors are provided with an internal
truss. It gives an extra strength in on the door
frame and nice outside look .
B - EXTERNAL TRUSS
The external truss I usually used in larger doors.
It gives an extra strength to the large frames
without adding extra weight.
9
BI-FOLD BARDUVA HANGAR DOORS
Locking Mechanism
The locking mechanism is connecting the shaft with the side locks through steel wires.
When the door reaches the closing point the locking arms (side locks) lock the door with
the frame and seal the door completely. Protecting it from any weather conditions.
Figure 7
Locking mechanism
Figure 8
Internal Truss
Locking arms
10
BI-FOLD BARDUVA HANGAR DOORS
INSTALLATION
Qualified Barduva professionals with many years of door installation experience, will install
doors quickly and flawlessly, although Barduva will provide you with detailed step by step instructions, in case you want to install your Fabric doors on your own. Our technical office staff
will be happy to answer all your questions.
Installation possibilities
Bifold Doors can be installed in two ways.
1.
Within the building’s door frame (Figure 9,10)
2.
Or with external frame in front for the building. (Figure 11– 16)
Figure 9
Figure 10
11
BI-FOLD BARDUVA HANGAR DOORS
Round Roof buildings
Figure 11
Figure 12
External
Frame
12
BI-FOLD BARDUVA HANGAR DOORS
Figure 13
Hinges (connect door frame
with external frame)
Figure 14
External frame
Building mounting points
Mounting points on ground
13
BI-FOLD BARDUVA HANGAR DOORS
Figure 15
Hinges (connect the two frame
sections together)
Figure 16
Heavy Duty Guide Rollers
14
BARDUVA
HANGARHANGAR
DOORS DOORS
BI-FOLD
BARDUVA
BIFOLD
HANGAR
DOORS
Email: [email protected]
phone: +370 5 231 0770
fax:
+370 5 231 0773
Liepkalnio str. 61
Lt 02120, Vilnius
Lithuania
www.hangardoor.eu
15