CDX-M700R/M750
Transcription
CDX-M700R/M750
CDX-M700R/M750 SERVICE MANUAL US Model Canadian Model Ver 1.2 2001. 03 CDX-M750 AEP Model UK Model CDX-M700R Photo: CDX-M750 • The tuner and CD sections have no adjustments. SPECIFICATIONS AUDIO POWER SPECIFICATIONS (CDX-M750) POWER OUTPUT AND TOTAL HARMONIC DISTORTION 19 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 1% total harmonic distortion. Other Specifications CD player section System Compact disc digital audio system Signal-to-noise ratio 90 dB Frequency response 10 – 20,000 Hz Wow and flutter Below measurable limit Laser Diode Properties (CDX-M750) Material GaAlAs Wavelength 780 nm Emission Duration Continuous Laser output power Less than 44.6 µW* * This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block. Model Name Using Similar Mechanism NEW CD Drive Mechanism Type MG-383V-121//K Optical Pick-up Name KSS-720A MW/LW (CDX-M700R) Tuning range MW: 531 – 1,602 kHz LW: 153 – 279 kHz Aerial terminal External aerial connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity MW: 30 µV LW: 40 µV Power amplifier section Outputs Speaker outputs Speaker impedance 4 – 8 ohms Maximum power output 50 W × 4 (at 4 ohms) General Outputs Inputs Tuner section FM Tuning range Power requirements 87.5 – 107.9 MHz (CDX-M750) 87.5 – 108.0 MHz (CDX-M700R) Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Usable sensitivity 8 dBf Selectivity 75 dB at 400 kHz Signal-to-noise ratio 66 dB (stereo), 72 dB (mono) Harmonic distortion at 1 kHz 0.6% (stereo), 0.3% (mono) Separation 35 dB at 1 kHz Frequency response 30 – 15,000 Hz AM (CDX-M750) Tuning range Antenna terminal Intermediate frequency Sensitivity 530 – 1,710 kHz External antenna connector 10.7 MHz/450 kHz 30 µV 9-870-134-12 Sony Corporation 2001C0400-1 © 2001. 3 Audio Entertainment Group General Engineering Dept. Audio outputs (3) Power antenna relay control lead (CDX-M750) Power aerial relay control lead (CDX-M700R) Power amplifier control lead Telephone ATT control lead Illumination control lead 12 V DC car battery (negative ground) – Continued on next page – FM/AM COMPACT DISC PLAYER CDX-M750 FM/MW/LW COMPACT DISC PLAYER CDX-M700R 1 CDX-M700R/M750 4-2. BLOCK DIAGRAM — CD SECTION — 4 RF AMP, LD APC, ERROR AMP IC1 OPTICAL PICK-UP KSS-720A A 5 DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR IC501 RF EQ RFO 16 61 RFAC EFM DEM PCMD D/A I/F I-V CONV. 8 LRCK DIGITAL CLV FE E 11 F 10 E F PD 4 TRACKING ERROR TE LD 3 50 13 52 51 PD 10 11 SUB CODE PROCESS SE LD ON 22 HOLD SW 21 AGC CONT 20 LD FOCUS COIL DRIVE 22 42 21 43 25 40 9 24 41 M902 SLED MOTOR 6 7 SLED MOTOR DRIVE 31 32 38 39 M901 SPINDLE MOTOR 12 13 SPINDLE MOTOR DRIVE 8 SQSO SQCK SCOR MD2 XRST DATA XLAT SCLK CLOK SENS GFS FOK TRACKING COIL DRIVE TRACKING COIL 34 19 17 18 14 6 77 BU IN 60 TRACKING/FOCUS COIL DRIVE SLED/SPINDLE/LOADING MOTOR DRIVE IC7 FOCUS COIL BUS CLK 51 BUS SI 52 17 CDM ON 18 CD ON BUS ON 61 RESET 30 46 LOCK FE TE • Signal path 5 ATT 58 CD EJECTOR 59 CD OPENREQ :CD 6 7 24 49 SI2 48 SCK2 64 SCOR 73 11 13 14 17 15 16 22 32 71 21 67 68 45 65 57 55 54 UNI CKO UNI SI UNI SO BUS ON SYS RST BU IN 90 RSTX SIRCS 24 86 HSTX S901 (RESET) IC902 LD AMP LD DRIVE Q101 14 LOCK SYSTEM CONTROL IC801 (1/3) MUTE CONT Q411 DATA CD ON MD ON 79 TO TUNER SECTION (Page 43) A MUT 19 OPEN 6 CLOSE 7 D FOCUS ERROR CD SYSTEM CONTROL IC5 16M BCK 54 RFDC D ATT TO DISPLAY SECTION (Page 44) XTAI 86 BCK 81 LRCK 77 A C 7 B 6 C B 1 18 35 FFDR TRDR BU 5V 1 RESET 2 SW501 (RESET) BATT (H) CHECK Q920 BATT BUS INTERFACE IC802 31 XIN X1 10MHz FRDR TFDR MD2 CD RST CD DATA CD XLAT SCLK CD CKO SENS GFS FOK 10 BATT (L) CHECK 3 13 RESET 2 12 BUS ON CONT 1 SERVO CTL SFDR SRDR MDP SW4 (LIMIT) 11 SSTP SW1 (DOWN) 10 D SW SW3 (DISC IN) 62 IN SW Q804 SW2 (SELF) 8 9 63 SELF SW DATA 6 8 M903 LOADING MOTOR 5 4 LOADING MOTOR DRIVE BATT 32 XOUT 1 2 69 66 40 70 20 22 23 MUTE 1 34 MUTE 2 35 LM EJ LM LOD SLED – DRIVE ON LD ON HOLD AGC CONT BUS SO 53 2 TO DISPLAY SECTION (Page 44) 04 42 42 SRST BUS CLK BUS SI BUS ON BU CHECK UNI SO LINK OFF SIRCS 11 CLK 6 5 4 3 2 1 7 4 CNP801 BUS CONTROL IN Q805 Q806 Q801 CDX-M700R/M750 4-3. BLOCK DIAGRAM — TUNER SECTION — PJ401 –1 (M750) ELECTRONIC VOLUME IC401 1 SEL R-CH 3 TO DISPLAY SECTION (Page 44) TUNER UNIT TU601 (ANTENNA) 1 ANT 2 ANT 34 33 35 24 7 –5 12 PRE AMP OUT RL 29 2 13 12 11 15 14 20 21 17 18 Q601 MUTE CONTROL Q604,606 MPX AM IF AM MP IV S METER SDA SCL QUAL MUTE –4 PJ402 –1 IC409 –2 SWR 25 4 TO CD SECTION (Page 42) (M750) POWER AMP IC903 Q403 MUTE CONTROL Q401, 402 ATT L R L R LINE OUT FRONT LINE OUT REAR L SUB OUT (MONO) R CNP901 1 FL+ 5 FL 12 9 Q410 NOISE FILT 1 IC602 BUS AUDIO IN R (M700R) 31 VOL ATT 32 TU ATT 5 –6 –3 13 R-CH SYSTEM CONTROL IC801 (2/3) BUF Q607 R-CH Q201 MPX 10 AM IF 19 AMDET 8 Q602 ACIFLR AC INLR SWINR OUTSSL L IC402 OUT FL 30 Q202 FL RL SR ADL –2 FL– 3 2 RL+ 9 50 QUALITY RL Q605 11 10 RDS 9 X601 4.3MHz 16 FM DET 4 XO 22 MUTE 4 STBY ST-BY 55 RDS DECODER IC601 TEL ATT ILL IN ACC IN X1A RDS 9 SCL 10 MPTH 2 5 XI 20 S METER DAVN 8 52 MPTH 75 DAVN RL– 7 56 NS MASK 16 95 81 73 X0A 74 Q923 ACC DET Q918 X802 32kHz R-CH ILL DET Q902 (M700R) S METER SDA IC SCL IC FM AGC SDA ROM SCL ROM 14 12 13 4 17 18 53 70 71 51 10 11 VSM I2CSIO I2CCKO FM AGC E2PSIO E2PCKO TEST 84 Q917 PW ON 83 X0 92 X1 93 X801 3.68MHz MD +B POWER CONT Q905, 919 COM 8V 5 6 POWER CONT Q461 BATT 4 FR+ 12 FR– 3 RR+ 11 RR– 13 ATT 14 ILL 7 ACC 15 TEST AMP REM ANT REM Q901 TU ON 114 • Signal path 04 MD +B : FM POWER CONT Q924, 925 : AM/MW 43 43 F901 TU 8V BATT 16 BATT CDX-M700R/M750 4-4. BLOCK DIAGRAM — DISPLAY SECTION — DISPLAY CONTROL IC301 BUS SI 98 UNI SI UNI SO 97 UNI SO 101 38 49 82 BUS CLK BUS ON BU CHECK 2 TO CD SECTION (Page 42) SB-SI 61 DSP CLK 63 SYSTEM CONTROL IC801 (3/3) UNI SCK BUS ON BU IN NMI AD ON CONT. Q807 BU 5V IC405 AD ON EMPH S RST 6 BUF 7 IC303 81 RES DSP 50 LINK OFF LINK OFF SIRCS KEY ACTIVE Q921 BU 5V DSP IC302 79 KEY ACK SO SI CKO RST LAT READY 26 25 27 36 35 78 63 61 59 57 62 60 IR RECEIVE 1 IC903 KEY IN MATRIX LCD DRIVER IC901 85 XTAL INH CLK DATA CEO DIMMER LCD902 86 EXTAL X351 18.43MHz 97 99 100 98 86 66 69 64 70 LCD901 CEO INH CLK CEI LCD DRIVER IC902 SW1 INH CLK DATA CEO MD +B CN502 ILL ON 9V TX (SO) RX (SI) FL SW 46 KEY IN0 47 KEY IN1 LRCK 2 3 76 LRCK BCK 5 6 75 BCK 106 116 115 4 12 13 ILL ON 52 POWER CONT. Q907,908 9 8 BOOT LED SW2 LED SW1 SP LATCH FLS SI FLS SO 1 AND 4 IC352 2 CD ON MD ON SW2 84 98 MOT+ 97 MOT– REG Q914 MD2 89 MD1 88 1 POWER CONT. Q912, 916 POWER CONT. Q901,902 Q906 Q905 3.3V REG 2 IC904 BU 5V BEEP 15 BEEP DRIVE Q803 4 BZ801 LCD9V 3 I DET 7 IC308 I DET Q302 DC/DC CONV. CONTROL IC901 96 I DET SW900 (OPEN/CLOSE) OPEN CLOSE OUT1 7 99 CLOSE SW LED DRIVE Q501,502 SHIFT 37 69 FLASH W 04 44 POWER CONT. Q903, 904 9 VCC 100 OPEN SW LCD 9V 44 ADL R-CH MCK0 40 X302 16MHz SHIFT Q909 1 REG 2 IC905 BU 5V CD 5V 3.3V REG 6 IC305 D 3.3V 3.3V REG Q301 A 3.3V • Signal path : FM 40 FPCRTL POWER CONT. Q903,904 ADL IN 35 DSP 5V 85 MT +B SR BATT BATT MD 5V 3 MOTOR 11 14 DRIVE IC307 6 16 12 IC406 DA2RO 43 58 MCKO POWER CONT. Q913, 915 CDON IN 76 DSP ON 108 MT +B R-CH(RR) 1 2 M601 OPEN/CLOSE MOTOR LCD9V REG IC306 3 RL MCK1 41 16M IC405 DA1RO 29 ADR IN 46 82 FLSWPWON VREF CONT. Q303,304 LCD 9V DATA TO CD SECTION (Page 42) R-CH(FR) 71 DATA 48 RC IN0 1 57 47 46 33 62 60 BATT 97 99 100 98 LATCH IC304 SW504 Z BOOT LED SW2 LED SW1 SP LAT RX TX/FL-SO DA3RO 54 77 MST/SLV 72 RC IN1 CNP803 (REMOTE IN) FL DAILO 27 DA3LO 52 DSPMST 29 IR RECEIVE 2 IC501 RVDT TRDT SCK DSP RST XLAT REDY : CD BATT ON/OFF DRIVE Q906 MD 5V ON/OFF DRIVE Q911 MD +B INA1 3 2 RT OUT2 10 INA2 14 3 TO TUNER SECTION (Page 43) CDX-M700R/M750 (Page 52) (Page 49) • Refer to page 45 for Waveforms. 4-7. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (1/2) — • Refer to page 60 for IC Block Diagrams. Note: • Voltage and waveforms are dc with respect to ground under no-signal conditions. no mark : CD PLAY : Impossible to measure ∗ (Page 49) 48 48 CDX-M700R/M750 • Refer to page 45 for Waveforms. 4-8. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (2/2) — • Refer to page 60 for IC Block Diagrams. (Page 48) (Page 48) Note: • Voltage and waveforms are dc with respect to ground under no-signal conditions. no mark : CD PLAY : Impossible to measure ∗ 49 49 CDX-M700R/M750 4-10. SCHEMATIC DIAGRAM — MAIN SECTION (1/4) — • Refer to page 60 for IC Block Diagrams. (Page 53) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM < > : CD PLAY (Page 48) (Page 54) 52 52 (Page 55) CDX-M700R/M750 (Page 52) 4-11. SCHEMATIC DIAGRAM — MAIN SECTION (2/4) — • Refer to page 60 for IC Block Diagrams. Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM ( ) : AM/MW (Page 54) (Page 55) 53 53 CDX-M700R/M750 4-12. SCHEMATIC DIAGRAM — MAIN SECTION (3/4) — • Refer to page 60 for IC Block Diagrams. (Page 53) (Page 55) (Page 52) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM 54 54 CDX-M700R/M750 4-13. SCHEMATIC DIAGRAM — MAIN SECTION (4/4) — • Refer to page 60 for IC Block Diagrams. (Page 52) (Page 53) (Page 54) (Page 57) (Page 59) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM 55 55 CDX-M700R/M750 4-14. PRINTED WIRING BOARD — SUB SECTION — (Page 51) 56 56 CDX-M700R/M750 4-15. SCHEMATIC DIAGRAM — SUB SECTION — (Page 55) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM 57 57 CDX-M700R/M750 (Page 55) 4-17. SCHEMATIC DIAGRAM — DISPLAY SECTION — 59 59
Similar documents
Aiwa CDC-R504MP, CDC-X504MP Service manual. www.s
US, Canadian Model: 87.5 – 107.9 MHz AEP, UK Model: 87.5 – 108 MHz Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Usable sensitivity 9 dBf Selectivity 75 dB at ...
More informationwalthers life like walthers proto walthers top dealer
SW9/1200 STANDARD DC $139.99 EA. #48403 PB&NE #43 #48418 CONRAIL #9117 #48419 CONRAIL #9118 #48420 N&W #2239 #48421 N&W #2244 #48422 COTTON BELT #1059 #48423 COTTON BELT #1060 #920-48414 SF #1240 #...
More information