Workstand 1 instructions English v17

3
i)
iii)
Filzer Filzer Pro Engineer Workstand WS-1
Clamp
Arm (J)
INSTRUCTIONS
Warning
The workstand maximum load is 25kg (55 lbs). Do not overload the workstand or you could damage your bike and/or workstand.
Ensure that the workstand is on a stable floor.
Ensure that you position/mount your bike on the workstand so the bike and stand are stable and do not fall over and cause injury or
damage.
Ensure that your bike is fastened to the workstand securely so it does not move, shift or fall off and damage your bike, stand and/or
property.
We recommend that you mount/clamp your bike to the workstand by your seatpost and not by your bike’s frame. If you clamp the
workstand to your bike frame you could crush or damage your bike frame.
Filzer is not responsible for any damage to your bike, stand, and/or property from the use of this workstand. And we are not
responsible for any injury caused by the workstand.
ii) Clamp Arm (J) should
face forwards in same
direction as Front Legs (H)
Main Tube Height
Adjustment
Quick-Release (E)
i) Open Main Tube Height
Adjustment Quick-Release (E),
and twist Clamp Arm (J)
180 degrees so it is
facing forwards
iii) Once Clamp Arm (J) is adjusted
to desired orientation lock the Main Tube
Height Adjustment Quick-Release (E)
Front Legs (H)
The Filzer Workstand comes fully assembled. To unfold and use the workstand follow these steps:
Workstand parts
Clamp Rotation Knob (A)
Clamp Arm (J) Bicycle Clamp Jaws (B)
4
Main Tube (F)
iii)
i)
iii)
ii)
Clamp Arm (J)
Bike Clamp Knob (C)
Clamp Pivot Knob (D)
Main Tube (F)
Main Tube Height
Adjustment
Quick-Release (E)
Main Tube Height Adjustment Quick-Release (E)
i) To adjust Clamp Arm (J) height, open
the Main Tube Height Adjustment
Quick-Release (E) and
Legs’ Quick-Release (G)
iii) Once Clamp Arm (J) is adjusted
to desired height lock the Main Tube
Height Adjustment Quick-Release (E)
ii) slide the Main-Tube (F) upwards
or downwards
5
Opening Workstand
Rear
Leg (I)
Bicycle Clamp
Jaws (B)
Front Legs (H)
1
i) To adjust Bicycle Clamp Jaws (B), turn the Bike Clamp Knob (C)
clock-wise to close or counter-clockwise to open jaws
Legs Quick-Release (G)
i) To open up workstand,
open Legs’ Quick-Release (G)
Bike Clamp Knob (C)
Note: To avoid possible bicycle frame damage,
it is highly recommended to clamp the bicycle
by the seatpost rather than the bicycle frame.
If you must clamp the frame, use minimal clamp
pressure to avoid damaging the frame. We are NOT
responsible for any damage caused to your bicycle
frame if you clamp the jaws to the frame!
ii) Slide Legs’ Quick-Release (G)
downwards and Front Legs (H)
forwards until the quick release
gets to the bottom and stops
iii) Close Legs
Quick-Release (G)
Front Legs (H)
Note if quick release is too
tight or loose, you can adjust
it with a hex wrench
Workstand folded
for storage
2
Clamp
Arm (J)
i) Twist Clamp Pivot Knob (D)
clockwise to loosen it
ii) Once (D) is fully
loosened, slid
Pivot Knob (D)
downwards
Clamp
Rotation
Knob (A)
6
(D)
Clamp Pivot
Knob (D)
i)
Clamp
Arm (J)
Clamp
Rotation
Knob (A)
(A)
Clamp Arm (J)
ii)
Clamp
Arm (J)
iii) Pivot the Clamp Arm (J)
upwards so it is horizontal
iv) Once clamp arm (J) is horizontal,
slide Clamp Pivot Knot (D) upwards
and twist it counter-clock-wise to lock
clamp arm (J) in place securely
i) To rotate the Clamp
Arm (J), loosen the
Clamp Rotation
Knob (A)
ii) Rotate Clamp
Arm (J) to desired
orientation
iii) Then lock the Clamp Arm (J)
by re-tightening the Clamp
Rotation Knob (A) securely
Filzer
Made in China
Fabriqué en Chine
www.filzer.com
Ver. 1